HYDROMASSAGE BATHTUB PUMP

INSTRUCTION MANUAL
LP SERIES PUMPS

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety
precautions should always be followed, including the following:
I.READ AND FOLLOW ALL INSTRUCTIONS
2.WARNING To leduce the risk of injury. Do not permit children to use this product
a unless they are closely supervised at all times.
3.WÀRNING Risk of Electrical Shock . Connected only to grounding type receptacle
protected by a ground fault circuit intenuptel'(GFCI). Contact a qualifred electrician
ifyoucannotverify thatthe receptacle is plotected byGFCI.
4.CAUTION Do not bury cord . Locate cord to minirnize abuse from lawnmowers,
hedge trimmers, and other equipment.
S.CAUTION In case the running parts will injure people, don't make the electric pump
running before then pipeline have been connected.
6.WARNING To reduce the risk of electrical shock, replace darnaged cord immediately.
T.WARNING To reduce the risk of electrical shock, do not use extension cord to connect
unit electric supply; provide a properly located outlet.
S.CAUTION This pump is for used for hx-installed bath tub, It is not suitable for s¡vimm-
ing pool spa.
9.Do not install within an outer enclosure or beneath the skirt of a hot tub unless so marked.
10. This appliance is not intended for use by persons with reduced physical sensory år
mental capabilities, or lack ofexperience and knowledge, unless they have been given
supelvision or instruction concerning use of the appliance by person respon sible for their
safety.
ll.Children should be supervised to ensure that they do not play with the appliance.
l2.Type Y attachrnent -Damaged supply cords to be replaced by the Manufacturer,service
agent or similarly qualified person to avoid haza¡d.
13. FOR INDOOR USE ONLY.
14. SAVE THESE INSTRUCTIONS.

I
 Do not dispose of electrical appliances as unsorted rnunicipal
waste, use separate collection facilities.
Contact you local govenllnent for infonnation regarding the
collection systems available.
Ifelectrical appliances are disposed ofin landfills or dumps,
hazardous substances can leak into the groundwater and get
I into the food chain, damaging your health and well-being.

l.GENERAL
- These instructions are for col'rect installation, and optirnnm performance
ofthe bath purnps, lead carefully.
so they should be
- These are single - stage centrifugal pumps designed to operate with
compact hydromassage equipment, They are equipped with a total
ernptying system to prevent the discharge of residual liquid in each
stopping.
- YlHz esp: See pump nameplate.
- These units are clesigned to operate with clean watel' at a maximum water
temperature of 50oC.
- Storage temperature: - I OoC - +5OoC. Relative Air Humidity :9 5Yo Max.
- Built of top quality materials, they are subjected to strict hydraulic ancl
electrical controls and ale carefully verified.
-Correct installation is ensured by following these instructions and those
of the wiring diagram; otherwise, over loads may be prodr.rced in the rnotor.
We decline responsibility for any damage caused by not follorving these
instructior-rs.
-General notes - ErP (ecological design-) directive
The benchrnark for rnost efficient water pumps is MEI > 0.10
The efficiency of a pump with a trimmed impeller is usually lower than that
of a pump with the full impeller diameter. The trirrming of the impeller:.¡vill
adapt the purnp to a fixed duty point, leading to reduced energy consumption.
The minirnurn efficiency index (MEI) is based on the full irnpeller diameter.
The operation of this water pump with variable duty points may be more,
efficient and economic when controlled, for example, by the use of a variable
speed drive that matches the pump duty to the system.
Information on benchmark efficiency is available at www.lingxiao.coln.cnl
2.INSTALLATION E
- Pumps must the level instalhnent, Dimensions and position of the pump
for supporting and fixing the pump within this space(Pig.2).
- Pump must be fixed by screw on the tub shelf, and fixed with silent block to
lower the noise and libration. Sticking and enlacing is forbiclden.
- The purnp will be getting hot in operating , to speed up cooling, the
minimum distance between the motor of the pump and the surrounding
structure should not be less then 20mm.
- The suction, pipe of the pump should be as short as possible.

2
- The rating Label must be visible after installation.
- Parts containing live parts, except parts supplied with safety extra low
voltage<12V, rnust be inaccessible to a person in the bath.
- Class I appliances must be perrnanently connected to fixed wiring. Part
including electrical components except remote control devices must be
located or fixed so that they cannot into bath.
3.PIPE ASSBMBT,Y
- The maximum inlet water pressure(0. 15MPa. ,.
- The suction pipes shoulcl have a diarneter equal to ol lalger than of the
dischalge pipes. lt can avoid the loss ofthe head and improve the efficiency.
- The suction and discharge pipes should not rest above the pump in any case.
- Seal all the conneçtors and unions well. Avoid any dripping on the motor,
which would unfailingly darnage it.
- Should be use the new hose module which supplements along with
the bathtub, the old hose module cannot be reusçd.
4.ELECTRICAL CONNECTION A
- The electrical install action should have a rnultiple separation systern with
contacts opening at least 3mm.
- For continued protection against possible electric shock this unit is to be
rlounted to the base in accordance with the installation instructions.
1) The protection of the system should be basedon aresidualcurrent
device (RCD) with a rated tripping current not exceeding 30m4.
The supply cable should comply with EMC standards.
2) Single-phase motors have built-in thermal protection.
- The electric connection must be carried out by qualified staff following
strictly the "EN60335-2-60' standard.
- Be sure that the earth cable connection is correctly rnade. t .

- Vy'ires serving as equipotential bonding conductors shall have a cross

sectional area between2.5mm2 and6mm2and shall be equipped with
the terminal suitable receptacle.
s.CONTROLS PRIOR TO INITIAL START.UP
- Verify that the purnp shaft turns freely.
- Check that the mains voltage and frequency are according to the name
plate.
- The hydromassage assembly should be equipped with a system to prevent
the pump from starting up if a minimum water level is not present.
- Check the rotating direction of the motor, which should concur with that
indicated on the fan cover.
- If the motor does not start up, try to locate the problem in the table of most
common faults and their possible solutions that is provided further on.
_THE PUMPSHOULD NEVER OPERATE DRY.

-J
 6.START-UP
- Start electrically the pump only when the suction and discharge pipes are
connected to the corresponding inlets and outlets.
-Apply voltage to the motor and suitably adjust the jets to obtain the
desired flow.
T.MAINTENANCE AND CTEAN E
- Our pumps for hydromassage facilities do nqt require any special
maintenance or programming. If the pump will be idle for a long period of
time , it is recommended to disassemble , clean and store it in a dry, well
ventilated place. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person to ahazard.
S.TROUBLB SHOOTING GUIDE
t
SYMPTOM POSSIBLE CAUSE CHECK
-Incoming power to the pump?
NO POV/ER -Is circuit breaker on?
TO PUMP -Is GFCI operating properly?
PUMP -Is the air switch plugged in?
DOES
NO TURN -Is the air switch hose connected to the
AIR SV/ITCH pump?
DISCONNECTED -Is the air switch hose connected to the
actuator button on the tub deck?
-Jets should be pointed away from the
suction inlet so air is not forced into
pump suction.
-Is the in tub suction inlet blocked
BLOCKAGE OR
or covered?
LEAK
PUMP -Is there any debris in the pump
NOT housing?
PUMPING -Is there a leak in the piping or the
PROPERLY pump?

-Is the proper voltage applied to the

LOW VOLTAGE pump?
-Is there an extension cord being used?

-4-
 9.INSTALLATION DIAGRAM
Suction Discharge pipe

Minimum water leve1 for the pump operation

a Fig.l
1 2:00 Location 1:30 Location
9:00 Location

2
_il

@
N
t-
dì
I

100

Fig.2

Power(P')
Model
L
KW HP

LP1s0(r) 1.10 1.5 382

1P200(T) 1.50 2.0 382

LP2s0(T) 1.85 2.5 382

1P300(T) 2.20 3.0 397

-5-
 L ooC] O
I o()v (Ð
O
() ú)
N $
O
a

o
æ
o
s
o
<f
o
N
o
o
a

{)
CD

o
o N
<r

(â
I I (]
O
t)
¡i
o
N
o
O
I
I
I
I I
I t- I l o
0)
I o
ro I
N
o
o N I I ()
o -fLJ
N
O
co
I
L I I o
N

¡r
o
co O
O I I
() O O N
fL
Êi o O
cf)
fL
I J I I o
Ò
I
J I I
I
Õ
.f
O
O fL
J
r)
N
I
o
C c I I
(D (}
u2
d- s
l E
E
o o O O
oÊ @ € N O (o
c!: a æ

(ru) pua¡1

Edition: 2019-07@

-6-