Bulletin No.

ITMS-B
Drawing No. LP0494
Released 1/07
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net

MODEL ITMS - INTELLIGENT TEMPERATURE TO MODBUS CONDITIONER W/ ALARMS

O TEMPERATURE TO MODBUS CONVERSION
O ACCEPTS THERMOCOUPLE, RTD, mV OR RESISTANCE
SIGNALS
O PROCESSOR BASED SCALING
O PC CONFIGURATION SOFTWARE
O DUAL SETPOINT RELAY ALARMS
O FOUR WAY SIGNAL ISOLATION

UL Recognized Component,
File # E179259

GENERAL DESCRIPTION SAFETY SUMMARY

The ITMS4037 Intelligent Temperature to MODBUS™ Conditioner with All safety related regulations, local codes and instructions that appear in the
Alarms accepts a wide range of temperature sensors (thermocouple and RTD manual or on equipment must be observed to ensure personal safety and to
elements), and converts the signal into a register format that can be read using prevent damage to either the instrument or equipment connected to it. If
either ASCII or RTU MODBUS protocol. equipment is used in a manner not specified by the manufacturer, the protection
The ITMS allows a choice of either Fahrenheit or Celsius readout with 0.1 or provided by the equipment may be impaired.
1 degree of resolution. An offset value can be programmed to scale the input
signal to meet most process requirements. Additionally, two setpoint values can
be entered for dual relay process monitoring alarms.
The ITMS is programmed with Windows™ based SFIMS software. The
software allows configuration, calibration, and storage of ITMS program files. CAUTION: Read complete CAUTION: Risk of electric shock.
Additionally, all setup parameters can be interrogated and modified through instructions prior to installation
MODBUS register and coil commands. and operation of the unit.
The RS485 port allows the ITMS to be multidropped, with Baud rates up to
38400. The CBPRO007 programming cable converts the RS232 port of a PC to
RS485, and is terminated with an RJ-11 connector. The bidirectional capability
of the CBPRO007 allows it to be used as a permanent interface cable as well as
a programming cable. DIMENSIONS In inches (mm)
The ITMS’s two relay alarms can be configured independently for absolute
high or low acting with balanced or unbalanced hysteresis. Alarm 2 can also be
configured for deviation and band alarms. In these modes, Setpoint 2 tracks
Setpoint 1. Adjustable alarm trip delays can be used for delaying output
response. The alarms can be programmed for Automatic or Latching. Latched
alarms can be reset with a serial command or a user input. A standby feature
suppresses the alarm during power-up until the temperature stabilizes outside
the alarm region. Standby eliminates power-up tripping for low acting alarms.
A user input can be used to set and reset non-latching alarms. The output relays
can also be manually controlled with register commands.
The module’s high density packaging and DIN rail mounting saves time and
panel space. The module is equipped with a universal mounting foot for
attachment to standard DIN rails, including top hat (T) profile or G profile rail.

ORDERING INFORMATION
MODEL DESCRIPTION PART NUMBER

ITMS Temperature to MODBUS Conditioner w/Alarms ITMS4037

SFIMS PC Configuration Software for Windows SFIMS
CBPRO Programming Interface Cable CBPRO007
Cable RJ11 to Unterminated 7 foot length CBJ11A07
CBJ
Cable RJ11 to RJ11 6 inch jumper CBJ11BD5
RJ Connector to Terminal Adapter DRRJ11T6

1
SPECIFICATIONS 11. MEMORY: Nonvolatile E2PROM retains all programmable parameters.
1. POWER: 18-36 VDC, 3.0 W max. or 24 VAC, ±10%, 50/60 Hz, 4 VA max. 12. ENVIRONMENTAL CONDITIONS:
2. INPUT: Operating Temperature Range: -20 to +65 °C
Sample Rate: 67 msec. (15 Hz) Storage Temperature Range: -40 to +85 °C
Failed Sensor Response: Open or shorted (RTD only) sensor coils indication, Operating and Storage Humidity: 85% max. relative humidity (non-
error code returned in Process Value condensing) from -20 to +65 °C
Common Mode Rejection: 50/60 Hz, 110 dB min. Altitude: Up to 2000 meters
Overvoltage: 30 VDC 13. CERTIFICATIONS AND COMPLIANCE:
Response Time: 150 msec. max. SAFETY
3. THERMOCOUPLE INPUTS: UL Recognized Component, File # E179259, UL3101-1, CSA 22.2 No. 1010-1
Types: T, E, J, K, R, S, B, N, C, linear mV Recognized to U.S. and Canadian requirements under the Component
Input Impedance: 20 MΩ Recognition Program of Underwriters Laboratories, Inc.
Lead Resistance Effect: 0.22 µV/Ω IECEE CB Scheme Test Certificate # US/5141A/UL,
Resolution: 1° or 0.1° for all types CB Scheme Test Report # 01ME11540-0702001
Issued by Underwriters Laboratories, Inc.
WIRE COLOR
TC TYPE DISPLAY RANGE
ANSI BS 1843
IEC 1010-1, EN 61010-1: Safety requirements for electrical equipment
-200 to +400°C (+) blue (+) white
for measurement, control, and laboratory use, Part 1.
T ELECTROMAGNETIC COMPATIBILITY
-328 to +752°F (-) red (-) blue
-200 to +750°C (+) violet (+) brown Immunity to EN 50082-2
E -328 to +1382°F (-) red (-) blue Electrostatic discharge EN 61000-4-2 Level 2; 4 KV contact
J -200 to +760°C (+) white (+) yellow Level 3; 8 KV air1
-328 to +1400°F (-) red (-) blue Electromagnetic RF fields EN 61000-4-3 Level3; 10 V/M
K -200 to +1372°C (+) yellow (+) brown 80 MHz - 1 GHz
-328 to +2502°F (-) red (-) blue Fast transients (burst) EN 61000-4-4 Level 4; 2 KV I/O
0 to +1768°C (+) white Level 3; 2 KV power
R No Standard
+32 to +3214°F (-) blue
RF conducted interference EN 61000-4-6 Level 3; 10 V/rms
0 to +1768°C (+) white 150 KHz - 80 MHz
S No Standard
+32 to +3214°F (-) blue
Simulation of cordless telephone ENV 50204 Level 3; 10 V/m
+200 to +1820°C 900 MHz ± 5 MHz
B No Standard No Standard
+392 to +3308°F
200 Hz, 50% duty cycle
-200 to +1300°C (+) orange (+) orange Emissions to EN 55011
N -328 to +2372°F (-) red (-) blue
RF interference EN 55011 Enclosure class A
C 0 to +2315°C Power mains class A
No Standard No Standard
W5/W26 +32 to +4199°F
mV -10 mV to 65 mV NA NA Notes:
1. This device was designed for installation in an enclosure. To avoid
4. RTD INPUTS:
electrostatic discharge to the unit in environments with static levels above
Type: 2 or 3 wire
6 KV, precautions should be taken when the device is mounted outside an
Excitation: 150 µA
enclosure. When working in an enclosure (ex. making connections, etc.),
Lead Resistance: 10 Ω max.
typical anti-static precautions should be observed before touching the module.
Resolution: 1° or 0.1° for all types
Refer to the EMC Installation Guidelines section of this bulletin for
RTD TYPE INPUT TYPE RANGE additional information.
100 Ω platinum, -200 to +800°C 14. CONSTRUCTION: Case body is black high impact plastic. Installation
385
Alpha=.00385 -328 to +1472°F
Category II, Pollution Degree 2.
100 Ω platinum, -200 to +800°C
392 15. CONNECTIONS: Wire clamping screw terminals.
Alpha=.003919 -328 to +1472°F
120 Ω nickel, -80 to +260°C 16. MOUNTING: Universal mounting foot for attachment to standard DIN
672
Alpha=.00672 -112 to +500°F style mounting rails, including top hat (T) profile rail according to EN50022
Ohms Linear Resistance 0 to 440 Ω - 35 x 7.5 and -35 x 15, and G profile rail according to EN50035 - G32.
5. INDICATION ACCURACY: ±(0.3% of span, +1°C), includes NIST 17. WEIGHT: 4.5 oz. (127.57 g)
conformity, cold junction effect, A/D conversion errors, tempco and
linearization conformity at 23°C after 20 minute warm-up.
Span Drift (max) : 0.01% /°C
BLOCK DIAGRAM
6. USER INPUT: Internally pulled up to +5 VDC. VIL = 0.78 V max.,
VIH = 1.8 V min. IOFF = 9 µA max. 30 V max. over voltage continuously.
7. ISOLATION LEVEL: 1.5 KV @ 50/60 Hz, 1 minute (150 V working)
between input, RS485 and power supply. 2300 Vrms, 1 minute (300 V
working) to relay contacts.
8. SERIAL COMMUNICATIONS:
Type: RS485; RTU and ASCII MODBUS modes
Baud: 300, 600, 1200, 2400, 4800, 9600, 19200, and 38400
Format: 7/8 bit, odd, even and no parity
Transmit Delay: Programmable. (See Transmit Delay explanation in Step 6)
Transmit Enable (TXEN): (primarily for 20 mA loop converter) open
collector VOH = 10 VDC max. VOL = 0.5 VDC @ 5 mA max. current limit
9. A/D CONVERTER: 16 bit resolution
10. RELAY OUTPUTS:
Type: 1 Form A N.O. contacts, 1 Form C DPDT
Rating: 5A @ 30 VDC or 250 VAC max. (resistive)
1/10 HP @ 120 VAC (inductive)
Response Time: 155 msec. max. to close including step response, 153 msec.
max. to open.
Output On Delay Time: Programmable from 0 to 32000 sec ±0.01% - 1 sec. max.

2
MODULE ISOLATION LED FUNCTIONALITY
The ITMS features “4-way” signal isolation. The 4-way isolation is a
CONDITION GREEN LED 2 RED LEDS
combination of optical, transformer and relay barriers, providing common mode
voltage (CMV) isolation to 1.5 KV for 1 minute between input, RS485, and Power Applied On ———
power supply. Isolation between relay contacts and all other inputs is 2300 Vrms
Communication Received Flashing ———
for 1 minute.
Respective Alarm On On
Checksum error Flashing Flashing
Calibration Off On

EMC INSTALLATION GUIDELINES

Although this module is designed with a high degree of immunity to Electro- 3. Signal or Control cables within an enclosure should be routed as far away as
Magnetic Interference (EMI), proper installation and wiring methods must be possible from contactors, control relays, transformers, and other noisy
followed to ensure compatibility in each application. The type of the electrical components.
noise, source or coupling method into the unit may be different for various 4. In extremely high EMI environments, the use of external EMI suppression
installations. Cable length, routing, and shield termination are very important devices, such as ferrite suppression cores, is effective. Install them on Signal
and can mean the difference between a successful or troublesome installation. and Control cables as close to the unit as possible. Loop the cable through the
Listed below are some EMC guidelines for successful installation in an core several times or use multiple cores on each cable for additional
industrial environment. protection. Install line filters on the power input cable to the unit to suppress
1. Use shielded (screened) cables for all Signal and Control inputs. The shield power line interference. Install them near the power entry point of the
(screen) pigtail connection should be made as short as possible. The enclosure. The following EMI suppression devices (or equivalent) are
connection point for the shield depends somewhat upon the application. recommended:
Listed below are the recommended methods of connecting the shield, in order Ferrite Suppression Cores for signal and control cables:
of their effectiveness. Fair-Rite # 0443167251 (RLC # FCOR0000)
a. Connect the shield only at the rail where the unit is mounted to earth TDK # ZCAT3035-1330A
ground (protective earth). Steward # 28B209-0A0
b. Connect the shield to earth ground at both ends of the cable, usually when Line Filters for input power cables:
the noise source frequency is above 1 MHz. Schaffner # FN610-1/07 (RLC # LFIL0000)
c. Connect the shield to common of the unit and leave the other end of the Schaffner # FN670-1.8/07
shield unconnected and insulated from earth ground. Corcom # 1 VR3
2. Never run Signal or Control cables in the same conduit or raceway with AC Note: Reference manufacturer’s instructions when installing a line filter.
power lines, conductors feeding motors, solenoids, SCR controls, and 5. Long cable runs are more susceptible to EMI pickup than short cable runs.
heaters, etc. The cables should be run in metal conduit that is properly Therefore, keep cable runs as short as possible.
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter.

3
 STEP 1 WIRING THE MODULE
WIRING CONNECTIONS RELAY OUTPUT CONNECTIONS
All conductors should meet voltage and current ratings for each terminal.
Also, cabling should conform to appropriate standards of good installation, local Relay 1
Relay 1 is a Form A output relay. Wiring is connected between terminal 9
codes and regulations. When wiring the module, use the numbers on the label to
(COMM.) common and terminal 8 (N.O.) the normally open contact.
identify the position number with the proper function. Strip the wire, leaving
approximately 1/4" (6 mm) of bare wire exposed. Insert the wire into the
terminal, and tighten the screw until the wire is clamped tightly. (Pull wire to Relay 2
verify tightness.) Each terminal can accept up to one #14 AWG (2.55 mm), two Relay 2 is a Form C output relay. Wiring is connected between terminal 4
#18 AWG (1.02 mm), or four #20 AWG (0.61 mm) wires. (COMM.) common and either terminal 5 (N.O.), the normally open contact, or
terminal 3 (N.C.), the normally closed contact.
To prolong contact life and suppress electrical noise interference due to the
MODULE POWER CONNECTIONS switching of inductive loads, it is good installation practice to install a snubber
AC module power is connected to terminals 1 and 2. DC module power is across the contacts. Follow the manufacturer’s instructions for installation.
connected with (+) to terminal 1 and (-) to terminal 2. For best results, the power
Note: Snubber leakage current can cause some high impedance loads to be held ON.
should be relatively “clean” and within the specified limits. Drawing power
from heavily loaded circuits or from circuits that also power loads that cycle on
and off should be avoided. It is recommended that power supplied to the module DEFAULT SERIAL SETTING CONNECTION
be protected by a fuse or circuit breaker. If the ITMS settings are unknown, or forgotten, they can be reset to the
factory defaults by connecting the Serial Default terminal 7 to Input Comm.
terminal 12 with a jumper, and then cycling power.
INPUT CONNECTIONS
Thermocouple Input Defaults:
Thermocouple leads are connected to terminals 11 (+) and 12 (-). Protocol: RTU Data Bits: 8
Address: 247 Parity: none
RTD Input
Baud Rate: 9600
For 3-wire RTD elements, connect the sense leads to terminals 11 and 12. The
excitation lead is connected to terminal 10 (EXC).
For 2-wire RTD elements, connect the sense leads to terminals 11 and 12.
Install a copper sense lead of the same gauge and length as the RTD leads. USER INPUT CONNECTION
Attach one end of the wire at the probe and the other end to terminal 10. The user input is activated when terminal 6 is pulled low (connected to Input
Complete lead wire compensation is obtained. This is the preferred method. If a Comm. terminal 12).
sense wire is not used, then Terminal 11 should be shorted to terminal 10. A
temperature offset error will exist. The error may be compensated by RS485 SERIAL CONNECTIONS
programming a temperature offset. There are two RJ-11 connectors located on the bottom for paralleling
communications. For single device communications, either connector can be
used. When used in conjunction with Red Lion Control Paradigm HMI products,
reverse A+ and B- wiring.

RJ11 ITMS
1 Not used
2 B-
3 A+
4 COMM 2 3 4 5
5 TXEN
ITMS CONNECTOR
6 Not used

STEP 2 INSTALLING SFIMS (Software for Intelligent Modules)

Insert the SFIMS diskette into the A: or B: drive. Then Run A:\SETUP
(or B:\SETUP) to install RLCPro onto the hard drive. An icon labeled
RLCPro will be created under the group RLCPro.

4
STEP 3 PROGRAMMING - Getting Started

You will be prompted to

select the proper device,

Run RLCPro by double-clicking the icon, or use the start menu.

Use the FILE pull-down menu

to select a NEW file. and then the model.

STEP 4 PROGRAMMING THE INPUT

The ITMS receives a temperature sensor input, converts it to a raw digital value, and stores this number in the ADC Value (register 40001). This number
is scaled into degrees, and a programmable Offset Value (register 40012), that can be used for sensor correction, is applied. The result is stored as the
Temperature Value (register 40002). It is also stored in the IEEE 754 Standard 32-bit floating decimal format (register 40003 and 40004). The non-scaled
ADC, the scaled Process Temperature Value, or the Floating Point Value may be accessed for the purpose of monitoring the input level.

IEEE STANDARD 754

FLOATING DECIMAL POINT
LO Order Byte Register 40003
HI Order Byte Register 40004

PROCESS
OFFSET TEMPERATURE
INPUT INTERNAL
ADC READING Register VALUE
SIGNAL MATH
Register 40001 40012 Register 40002

Input Type: Select the proper input type from the pull down menu.

Scale: Select Fahrenheit or Celsius. In linear millivolt or resistance modes, this has no
effect.
Resolution: For thermocouple, RTD, or linear resistance modes, low resolution selects
whole degrees or ohms. In these same modes, high resolution selects tenth of degrees
or ohms. In linear mV mode, low selects hundredths of mV, and high selects
thousandths of mV.
Offset: The Offset value can be used as a sensor correction value.

Filter Response: The Filter Response is a time constant, in tenth of second increments,
that is used to stabilize an erratic input. The Process Value stabilizes to 99% of the final
value within approximately 5 time constants. A value of ‘0’ disables digital filtering.
Filter Band: Filter Band is a value expressed in Temperature (degrees or tenths) units.
When a fluctuating signal remains within the band value, the Digital Filter is active,
and therefore stabilizes the Process Temperature Value. When a fluctuating signal
exceeds the Filter Band value, the Digital Filter is momentarily disabled to allow for
quick response to valid process changes. Once the signal variation is less than the Filter
Band value, the Digital Filter is reactivated.

5
STEP 5 PROGRAMMING THE ALARMS
Action: Alarm 1 can be programmed for 5 modes of operation, Alarm 2 has 9 possible modes. See
Setpoint Alarm figures for illustration.
Manual: In Manual mode, the Alarms are forced on and off by writing ‘0’ or ‘1’ to the appropriate
MODBUS register (Alarm 1 state = 40027, Alarm 2 state = 40028). The alarms are
configured for this action from the factory. In this mode, the alarms will not respond to their
setpoint or hysteresis values.
Absolute HI: (with balanced or unbalanced hysteresis) The Alarm energizes when the Temperature
Value exceeds the Setpoint Limit Value.
Absolute LO: (with balanced or unbalanced hysteresis) The Alarm energizes when the Temperature
Value falls below the Setpoint Limit Value.
Deviation HI, Deviation LO, Band Inside or Outside: In these modes, Alarm 2 “tracks”
Alarm/Setpoint 1.
Setpoint: The alarm Setpoint value, entered in degrees. If the ITMS is programmed for mV or resistance modes, then the Setpoint is in mV or Ohms,
respectively.

Hysteresis: Hysteresis is used to eliminate output chatter. The Hysteresis Amount is the difference between the points where an Alarm will turn on
and turn off. In Unbalanced modes, the alarm turns on at the Setpoint, and turns off at Setpoint minus hysteresis for HI alarms, and Setpoint plus
hysteresis for LO alarms. In Balanced modes, the hysteresis is evenly divided above and below the Setpoint value. (See the Setpoint Alarm
Figures.)
Note: The Setpoint, along with the Hysteresis, MUST NOT produce a “trigger point” higher than 32,000, or less than -32,000. (See the Setpoint
Alarm Figures.)

Trigger Points: Trigger Points are the Process Values where the alarm state changes. Their values cannot be entered directly, but are shown as a
reference in the SFIMS software. The Setpoint Value, Hysteresis Value, and Setpoint Alarm Type determine the trigger points. With Deviation or
Band modes, Setpoint 1 and Setpoint 2 are combined to determine the trigger points. Trigger Points cannot be greater than +32000 or less than -
32000. If these limits are exceeded, the alarm is disabled and an alarm threshold over range error is set. The Trigger Points can be outside the
Temperature Value range for a given sensor type without receiving an error, but the alarm will not change state for that trigger point.
Reset: The alarms can be programmed for Automatic or Latched. In Automatic mode, an energized alarm turns off by itself once the Process Value
leaves the alarm region. In Latched mode, an energized alarm requires a reset from the User input, or a serial reset command. This is done by
writing a ‘0’ to the appropriate MODBUS register. (Alarm 1 state = 40027, Alarm 2 state = 40028)

On Delay: The time, in whole second increments, that the alarm will take to energize when the Process Value enters into an alarm region.

Enable Standby Delay: Standby prevents nuisance (typically low level) alarms after a power up. After powering up the unit, the temperature must
leave the alarm region. Once this has occurred, the standby is disabled, and the alarm responds normally until the next module power up.

User Input Action: The User Input can be programmed to Reset, or Set, either Alarm 1, Alarm 2, or both. The User Input is activated when terminal
6 is pulled low. (Connected to the Common terminal 12.)

User Input Activation: The User Input can be programmed to respond as a Level (maintained) or Edge (momentary) input. See the User Input Mode
Operation Table below.

Sensor Failure Action: This setting allows different alarm responses when the temperature sensor fails. The ITMS can be programmed to turn one
or both alarms on or off.

USER INPUT MODE OPERATION

INPUT INPUT AUTOMATIC ALARM LATCHED ALARM
ACTION ACTIVATION IN ALARM REGION OUTSIDE ALARM REGION IN ALARM REGION OUTSIDE ALARM REGION
Resets and puts the alarm in Resets and puts the alarm in
Reset Edge Standby mode; resets alarm if in No action Standby mode; resets alarm if in Resets alarm if on
Hysteresis band Hysteresis band

Set Edge No action No action No action Sets alarm latched

Resets alarm while input is active, Resets alarm while input is active,
resumes normal operation when resumes normal operation when
Reset Level No action Resets alarm if on
input is inactive; resets alarm if in input is inactive; resets alarm if in
Hysteresis band Hysteresis band

Sets alarm while input active,

Set Level No action resumes normal operation when No action Sets alarm latched
input is inactive

6
SETPOINT ALARM FIGURES

STEP 6 PROGRAMMING THE ITMS COMMS PORT

MODBUS Protocol: RTU or ASCII BAUD RTU ASCII
Unit Address: 1-247 38400 2 msec. 2 msec.
Baud Rate: 300, 600, 1200, 2400, 4800, 9600, 19200, or 38400 19200 3 msec. 2 msec.
Data Bits: 7 or 8 9600 5 msec. 2.3 msec.
Parity: odd, even, or none 4800 9 msec. 4.6 msec.
Transmit Delay: Programmable from 1-255 milliseconds. The Transmit 2400 17 msec. 9.2 msec.
Delay is the time the ITMS waits to respond to a serial command, 1200 33 msec. 18.4 msec.
UNLESS the values in the table are larger. 600 65 msec. 36.7 msec.
300 129 msec. 73.4 msec.
Note: If the communication settings are changed and then a download is
performed, the module will now respond to the new settings. Any further attempts to communicate to the module
must target the new address, with the new settings. If you do not know or cannot recall the ITMS settings, they
can be reset to factory defaults. Connect the Serial Default terminal to Common, and cycle power. The Defaults
button in the SFIMS software will update the category display to these settings.
Communications Diagnostics: The Communications Diagnostics function can be used to troubleshoot systems that are
experiencing communication errors. Press the Read button to retrieve the diagnostics information. The Commands
Received and the Commands Processed values are automatically reset when the values are read, and at each unit power-up.
Commands Received: The number of messages received that started with the units own address.
Commands Processed: The number of “good” messages received. A “good” message is considered one that contained the
correct unit address, parity, and checksum (CRC or LRC).

7
STEP 7 PC PORT CONFIGURATION

Go to the SETTINGS pull-down menu, and select PC PORT SETTINGS.

The Communications Settings window allows you to set up the software properly to perform a download.

Connection: Select the computer port (COMM 1-4) that the ITMS is connected to.
Note: The following settings must match the ITMS. If you do not know or cannot recall the ITMS settings, they can
be reset back to factory defaults. Simply jumper the Serial Default terminal to Common, and cycle power. The
serial settings will default to RTU mode, 9600 baud, 8 data bits, No parity, with an address of 247.
Protocol: RTU or ASCII
Unit Address: 1-247
Baud Rate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400
Data Bits: 7 or 8
Parity: odd, even, or none

Connect the ITMS to the computer with the CBPRO007 interface cable (or any suitable RS232/RS485 converter).
Apply 18-36 VDC to the supply terminals of the ITMS.

Note: The CBPRO007 download cable DOES NOT

typically require power. In most cases it will derive
its power from the PC. If communications can not be
established, follow the troubleshooting guide. If it is
determined that the converter requires power, attach
a 12 VDC power supply to the VDC and common
terminals of the cable.

STEP 8 DOWNLOADING
Go to the FILE pull-down menu, and select DOWNLOAD.

The following screen prompts you to

ensure that the proper file is downloaded
to the correct module. Click “OK” to
continue.

8
STEP 9 SCRATCH PAD MEMORY
The Scratch Pad category can be used to read or write to the Scratch Pad memory locations (41101-
41116). The Scratch Pad locations can be used to store user information.

Data Format: Allows registers to be viewed in decimal or hexadecimal format.

Upload: The Upload button causes SFIMS software to read the Scratch Pad registers from the module.

Download: The Download button causes SFIMS software to write to the Scratch Pad registers in the
module.
Note: Downloading new values to the module Scratch Pad locations overwrites the information that is
currently stored in those registers.

STEP 10 VIEW REGISTERS

The View Registers category can be used as a method of diagnostics. Use the ITMS Register Table
as a reference of register assignments and data.

First Register: This specifies the first, or only, register to be read in a block.

# of Registers: This is the length of the block to be read. The module supports block read and write
commands up to 16 registers in length.

Data Format: Allows registers to be viewed in decimal or hexadecimal format.

Read: Clicking the Read button causes SFIMS software to read the selected register from the module.

Write: Clicking the Write button causes SFIMS software to write the selected registers to the module.

Note: The Write button overwrites the existing register values, and may change the module setup and
operation.

STEP 11 CALIBRATION
The ITMS is fully calibrated from the factory. Recalibration is recommended every two years. Each
range has its own internal references that are recalled when the range is selected. This allows
independent calibration for each range. All calibration settings are stored in the E2PROM. Calibration
may be performed by using SFIMS software or MODBUS commands.
RTD and CJ calibrations are dependent on the millivolt calibration and, therefore, must be performed
after a millivolt calibration has been completed. RTD or CJ calibration may be performed independently
of the millivolt calibration.

Calibration Type: This specifies the type of calibration to be performed.

Cold Junction Calibration:

TC Type: This selects the type of TC that is being used to calibrate the cold junction.
Scale: This selects the scale in which the Thermometer temperature is entered and the Module
temperature is displayed.
Thermometer: Enter the reference thermometer temperature here.
Module: This displays the ITMS process temperature value after a cold junction calibration is
completed to verify the accuracy.

Calibrate: The Calibrate button initiates the calibration process after the appropriate settings are
selected.

Note: Millivolt calibration requires a precision voltage source with an accuracy of 0.025% or better.
Allow the ITMS to warm up for 30 minutes minimum and follow the manufacturer’s warm-up
recommendations for the calibration source. RTD calibration requires a 0.1% precision 300 ohm
resistor. CJ calibration should be performed with a TC of known accuracy of types T, E, J, K, C or N
only. When using SFIMS for calibration, select the type of calibration to be performed, and press the
Calibrate button. Follow the calibration procedures in the software.

9
TROUBLESHOOTING
PROBLEM CAUSE REMEDIES
Green LED will not light Module power Check module power connections and voltage level
Process Value not changing Input signal Check input signal connections and signal level
Process Value not changing or incorrect Incorrect scaling Check input setup, scaling values, and re-download
Alarms disabled Alarm threshold over range*; checksum Adjust alarm Setpoint and Hysteresis to ensure trigger
error; Input over/under range; open or point is within -32000 to +32000 (See Alarm setup). For
shorted probe*; calculated results over other possible causes, see the remaining remedies
+32000 or -32000; in Calibration Mode
Process Value stays at 32001 or -32001 Input over or under range* due to:
Wrong TC, or RTD Check input level
Incorrect input type Check input type, and re-download
Process Value stays at 32002 Open TC or RTD:* Check input signal connections and probe
Process Value stays at -32002 Shorted RTD:* Check input signal connections and probe
Process Value stays at +32003 or -32003 Calculated Temp. value over +32000 or Check offset value, Register 40012
-32000
Process Value stays at 32100, Flashing Parameter checksum*, loss of Re-download SFIMS file (reconfigures each parameter)
LEDs, alarms disabled parameter settings
Calibration checksum* Perform calibration procedure
Will not communicate Incorrect serial settings (ITMS port) Verify ITMS communications setup
(Green LED not flashing) Incorrect serial settings (computer port) Go to pull down menu SETTINGS, PC PORT SETTINGS
Incorrect wiring Try switching A+ and B- lines
Provide a common connection
NOTE: The ITMS’ serial settings must match the device that it is communicating with. If you do not know or
cannot recall the ITMS settings, they can be reset back to factory defaults. Simply jumper the Serial Default
terminal to Common, and cycle power. The serial settings will default to RTU mode, 9600 baud, 8 data bits, no
parity, with an address of 247.
* Can be monitored by accessing coils 9-16, or register 40025.
For further technical assistance, contact technical support.

INSTALLATION
The unit is equipped with a universal mounting foot for attachment to standard DIN style mounting rails, including G profile rail
according to EN50035 - G32 , and top hat (T) profile rail according to EN50022 - 35 x 7.5 and 35 x 15. The unit should be installed in a
location that does not exceed the maximum operating temperature and provides good air circulation. Placing the unit near devices that
generate excessive heat should be avoided.

G Rail Installation T Rail Installation

To install the ITMS on a “G” To install the ITMS on a “T”
style DIN rail, angle the module style rail, angle the module so
so that the upper groove of the that the top groove of the “foot”
“foot” catches under the lip of the is located over the lip of the top
top rail. Push the module toward rail. Push the module toward the
the rail until it snaps into place. rail until it snaps into place. To
To remove a module from the remove a module from the rail,
rail, push up on the bottom of the insert a screwdriver into the slot
module while pulling out and on the bottom of the “foot”, and
away from the rail. pry upwards on the module until
it releases from the rail.

APPLICATION
A chemical company wanted to remotely monitor the
temperature of several holding tanks. Using the ITMS, the
customer was able to receive, interpret, and store the
temperature readings via standard thermocouples. To provide a
remote display, the customer chose a Red Lion Paradigm HMI
(Human Machine Interface). The HMI communicates with the
ITMS modules and displays the information graphically,
providing an intuitive interface. As an added benefit, the ITMS
alarm setpoints can be adjusted from the HMI, while providing
reliable local alarm outputs.

10
 MODBUS INFORMATION
The remaining sections of this bulletin list ITMS Register Format information and MODBUS conformity.

MODBUS SUPPORTED FUNCTION CODES 03: Illegal Data Value

Issued when an attempt is made to read or write more registers or coils than
FC01: Read Coils
the unit can handle in one request.
1. Valid coil addresses are 1-16.
2. Only 16 coils can be requested at one time. 07: Negative Acknowledge
3. Block starting point can not exceed coil 16. Issued when a write to coil or register is attempted with an invalid string
FC05: Force Single Coil length.
1. Valid write (force) coil addresses are 1-10. CHECKSUM ERRORS
2. <8001>HEX is echoed back that the coil did not change during the request to 1. Calibration checksum covers the E2 PROM that contains calibration values
write to a read only coil. for all ranges. When a calibration checksum error occurs, coil 10 becomes a
FC15: Force Multiple Coils 1. (See Coils Table)
1. Valid write (force) coil addresses are 1-10. 2. Parameter checksum covers the E2 PROM that contains the stored Holding
2. Block starting point can not exceed coil 10. register settings. When a parameter checksum error occurs, coil 9 becomes a
3. If a multiple write includes read only coils, then only the write coils will change. 1. (See Coils Table)
3. All of the LEDs will flash as long as either error occurs.
FC03: Read Holding Registers 4. The alarms are disabled as long as either error occurs.
1. Valid addresses are 40001-40029, 41001-41010, 41101-41116. 5. Either error can be cleared or activated manually by writing to the appropriate
2. Only 16 registers can be requested at one time. coil. (This does not correct the reason for the error. It may be necessary to
3. Block starting point can not exceed the register boundaries. reconfigure or calibrate.)
4. <8000>HEX is returned in registers beyond the boundaries. 6. Both checksums are verified at power up.
5. Holding registers are a mirror of Input registers.
FC06: Preset Single Register CALIBRATION
1. Valid write (preset) addresses are 40006-40029, 41101-41116. Calibration may be performed by using SFIMS software, or MODBUS
2. <8001>HEX is echoed back that the register did not change during the commands. Review Calibration explanation in Step 11, before performing these
request to write to a read only register. steps.
3. If the write value exceeds the register limit (see Register Table), then that
register value changes to its exceeded high or low limit. It is also returned in mV Calibration
the response. 1. Connect the signal source to proper ITMS terminals.
2. To set Input Type, enter 9 into register 40008.
FC16: Preset Multiple Registers 3. To start calibration, enter <7777> HEX into register 40029.
1. Valid write (force) register addresses are 40006-40029, 41101-41116. 4. To start ADC calibration, enter <0001> HEX into register 40029.
2. No response is given with an attempt to write to more than 16 registers at a time. 5. Apply the appropriate voltage and enter the corresponding <>HEX value into
3. Block starting point can not exceed the read and write boundaries. register 40029 for each range to be calibrated.
4. If a multiple write includes read only registers, then only the write registers 0 mV <0002>, 14 mV <0003>, 28 mV <0004>, 42 mV <0005>, 56 mV <0006>
will change. 6. To save the values and end calibration, enter <0000> HEX into register 40029.
5. If the write value exceeds the register limit (see Register Table), then that
register value changes to its exceeded high or low limit. CJ Calibration
Note: In this procedure, write functions are performed in HEX and a write to a
FC04: Read Input Registers
register is monitored by a read in a different register.
1. Valid addresses are 30001-30029, 31001-31010, 31101-31116.
1. Connect the thermocouple probe source to the proper ITMS terminals. (Types
2. Only 16 registers can be requested at one time.
T, E, J, K, N and C only).
3. Block starting point can not exceed register boundaries.
2. To set Input Type, enter connected TC type into register 40008.
4. <8000>HEX is returned in registers beyond the boundaries.
3. To set Scale, enter 1 for °C or 0 for °F into register 40006.
5. Input registers are a mirror of Holding registers.
4. To set High Resolution, enter 1 into register 40009.
FC08: Diagnostics 5. Place an external reference thermometer probe at the end of the ITMS probe.
The following is sent upon FC08 request: The two probes should be shielded from air movement and allow sufficient
Unit Address, 08 (FC code), 04 (byte count), “Total Comms” 2 byte count, time to equalize in temperature. (As an alternative, the ITMS probe may be
“Total Good Comms” 2 byte count, checksum of the string. placed in a calibration bath of known temperature.)
“Total Comms” is the total number of messages received that were addressed to 6. To start calibration, enter <7777> HEX into register 40029.
the ITMS. “Total Good Comms” is the total messages received by the ITMS 7. To start CJ calibration, enter <0010> HEX into register 40029.
with good address, parity and checksum. Both counters are reset to 0 upon 8. Read the Process Temperature Value register 40002 (Read as an Integer).
response to FC08. 9. Subtract the external reference reading from the Process Temperature Value
FC17: Report Slave ID register 40002 reading. Adjust the results to hundredths position, drop
The following is sent upon FC17 request: decimal point, and maintain the results sign. (If the difference is -2.0 degrees,
Unit Address, 17 (FC code), RLC-ITMS4037, 0100 (for code version 1.00), 16 then adjust to -2.00 and remove decimal point yielding a value of -200.)
(number of read supported registers), 16 (number of writes supported 10. Enter <0011> HEX into register 40029.
registers), 16 (number of registers available for GUID/ Scratch pad memory), 11. Add the value from step 9 (maintain the sign) to the value existing in register
checksum of the string. 40007 (Read as an Integer).
12. If necessary, continue to adjust register 40007 value until the Process
The following is the HEX of the above (with unit address of 247): Temperature Value register 40002 matches the external reference reading.
<F7><11><14><52><4C><43><2D><49><54><4D><53><34><30><33> 13. To save the values and end calibration, enter <0000> HEX into register
<37><01><00><00><10><00><10><00><10><8D><9F> 40029.
RTD Calibration
SUPPORTED EXCEPTION CODES 1. Connect precision 300 ohm resistor to terminals 11 & 12. Short terminals 10 & 11.
01: Illegal Function 2. To set Input Type, enter 13 (Integer) or <000D> HEX into register 40008.
Issued whenever the requested function is not implemented in the unit. 3. To start calibration, enter <7777> HEX into register 40029.
02: Illegal Data Address 4. To start 0 ohm RTD calibration, enter <0015> HEX into register 40029.
Issued whenever an attempt is made to access a single register or coil that 5. Apply 0 ohms by shorting terminals 11 & 12 for 10 seconds.
does not exist (outside the implemented space) or to access a block of registers 6. To start 300 ohm RTD calibration, enter <0016> HEX into register 40029.
or coils that falls completely outside the implemented space. 7. Apply 300 ohms by removing short from terminal 11 for 10 seconds.
8. To save the values and end calibration, enter <0000> HEX into register 40029.

11
 REGISTER TABLE
The below limits are shown as Integers or HEX < > values. Read and write functions can be performed in either Integers or HEX as long as the conversion was
done correctly. Negative numbers are represented by two’s complement.
REGISTER
REGISTER NAME LOW LIMIT† HIGH LIMIT† ACCESS COMMENTS
ADDRESS *
40001 ADC reading N/A N/A Read Only ADC (Analog to Digital Converter) reading of present input level.
40002 Process Temperature Value N/A N/A Read Only Process Value (with scale and offset) of present input level.
IEEE Standard 754 Floating Decimal Point, low order of Temperature Value.
40003 Floating Point LO N/A N/A Read Only
(Allows 32 bit accuracy for external monitoring.)
IEEE Standard 754 Floating Decimal Point, high order of Temperature Value.
40004 Floating Point HI N/A N/A Read Only
(Allows 32 bit accuracy for external monitoring.)
40005 User Input Pin State N/A N/A Read Only 0 = Active, 1 = Inactive.
40006 Temperature Scale 0 1 Read/Write 0 = °F, 1= °C.
40007 CJ Temp -32000 32000 Read/Write Cold Junction calibration temp (1 = 0.01°C).
40008 Input Type 0 13 Read/Write See Input Type Register Table.
40009 High Resolution 0 1 Read/Write 0 = 1 degree, 1 = 0.1 degree.
40010 Filter Band 0 32000 Read/Write See Filter Band explanation.
40011 Filter Response Time 0 1000 Read/Write See Filter Response Time explanation (1 = 0.1 second).
40012 Offset Value -32000 32000 Read/Write See Offset explanation.
40013 User Input Action <0000> <0015> Read/Write See User Input Action Register Table.
40014 Alarm 2 Action <0000> <0038> Read/Write See Alarm 1 & 2 Action Register Table.
40015 Setpoint 2 Value -32000 32000 Read/Write Alarm 2 setpoint value based on Process Value.
40016 Alarm 2 Hysteresis 1 32000 Read/Write Alarm 2 hysteresis value based on Process Value.
40017 Alarm 2 Delay 0 32000 Read/Write Alarm 2 delay trip on time (1 = 1 second).
40018 Alarm 1 Action <0000> <0034> Read/Write See Alarm 1 & 2 Action Register Table.
40019 Setpoint 1 Value -32000 32000 Read/Write Alarm 1 setpoint value based on Process Value.
40020 Alarm 1 Hysteresis 1 32000 Read/Write Alarm 1 hysteresis value based on Process Value.
40021 Alarm 1 Delay 0 32000 Read/Write Alarm 1 delay trip on time (1 = 1 second).
40022 Sensor Failure Action 0 3 Read/Write See Sensor Failure Action For Alarm State Table.
40023 Transmit Delay 1 255 Read/Write Delay before serial transmission (1 = 1 msec). See Transmit Delay Explanation.
40024 Node (Unit) Address 1 247 Read/Write Node serial ITMS address.
40025 Error Coils <0000> <0003> Read/Write Mirror of Coils 9-16. See Coil Table.
40026 Comm. Coils <0020> <00FF> Read/Write Mirror of Coils 1-8. See Coil Table and Communications Table.
40027 Alarm 1 State 0 1 Read/Write Alarm 1 state (1 = on).
40028 Alarm 2 State 0 1 Read/Write Alarm 2 state (1 = on).
40029 Factory Calibration <0000> <7777> Read/Write See MODBUS Calibration explanation.
ITMS-4037, 0100 (ver. 1.00), 16 reads, 16 writes, 16 scratch. The version value
41001- 41010 Slave ID See FC17. See FC17. Read Only
could be higher.
This area is for the user to store any related information.
41101- 41116 GUID/Scratch <0000> <FFFF> Read/Write
This register area does not affect ITMS operations.

* For Input Registers, replace the 4xxxx with a 3xxxx in the above register address. The 3xxxx are a mirror of the 4xxxx Holding Registers.
† An attempt to exceed a limit will set the register to its high or low limit value.

COILS TABLE (COMMUNICATION AND ERRORS)

COIL ADDRESS COIL NAME ACCESS COMMENTS
1 Baud B0 Read/Write See Communication Register and Coils Table.
2 Baud B1 Read/Write See Communication Register and Coils Table.
3 Baud B2 Read/Write See Communication Register and Coils Table.
4 Parity B3 Read/Write See Communication Register and Coils Table.
5 Parity B4 Read/Write See Communication Register and Coils Table.
6 Data Bits B5 Read/Write See Communication Register and Coils Table.
7 Mode B6 Read/Write See Communication Register and Coils Table.
8 Change B7 Read/Write “1” = Change ITMS communications to above settings.
9 P. Checksum Error Read/Write “1” = Parameter checksum error, disables alarms, causes flashing LEDs.
10 C. Checksum Error Read/Write “1” = Calibration checksum error, disables alarms, causes flashing LEDs.
11 AL 1 Over Range Read Only “1” = Alarm 1 Threshold over range, disables alarms, causes no LED indication.
12 AL 2 Over Range Read Only “1” = Alarm 2 Threshold over range, disables alarms, causes no LED indication.
13 Open Input Read Only “1” = Open RTD or TC, causes Process Temp. Value to be 32002, disables alarms, causes no LED indication.
14 Over Range Read Only “1” = Over Range, causes Process Temp. Value to be 32001, disables alarms, causes no LED indication.
15 Under Range Read Only “1” = Under Range, causes Process Temp. Value to be -32001, disables alarms, causes no LED indication.
16 Shorted RTD Read Only “1” = Shorted RTD, causes Process Temp. Value to be -32002, disables alarms, causes no LED indication.

Coils 1-7 mirror register 40026 and Coils 9-16 mirror register 40025.

12
 INPUT TYPE REGISTER (40008) TABLE USER INPUT ACTION REGISTER (40013) TABLE
MODE TYPE MODE TYPE MODE TYPE MODE ACTION ALARM INPUT ACTIVATION
0 Tc - T 5 Tc - S 10 RTD - 385 <0000> Reset 1 Level (Maintained)
1 Tc - E 6 Tc - B 11 RTD - 392 <0001> Reset 2 Level (Maintained)
2 Tc - J 7 Tc - N 12 RTD - 672 <0002> Reset 1&2 Level (Maintained)
3 Tc - K 8 Tc - C 13 LIN Ohms <0003> Set 1 Level (Maintained)
4 Tc - R 9 LIN mV <0004> Set 2 Level (Maintained)
<0005 Set 1&2 Level (Maintained)
<0010> Reset 1 Edge (Momentary)
SENSOR FAILURE ACTION REGISTER (40022) TABLE
FOR ALARM STATE CONDITION <0011> Reset 2 Edge (Momentary)
<0012> Reset 1&2 Edge (Momentary)
MODE ALARM 1 ALARM 2
<0013> Set 1 Edge (Momentary)
0 Off Off
<0014> Set 2 Edge (Momentary)
1 On On
2 Off On <0015> Set 1&2 Edge (Momentary)

3 On Off

ALARM 1 (40018) & 2 (40014) ACTION REGISTER TABLE

Latched 2nd Nibble 1st Nibble
ACTION MODE ALARMS B3 B2 B1 B0
Stand By Off=Auto B7 B6 B5 B4 HEX HEX
Manual 0 1 2 0 0 0 0 < 0>
off off 0 0 0 0 <0 >
off on 0 0 0 1 <1 > Absolute Hi, balanced 1 1 2 0 0 0 1 < 1>

on off 0 0 1 0 <2 > Absolute Lo, balanced 2 1 2 0 0 1 0 < 2>

on on 0 0 1 1 <3 > Absolute Hi, unbalanced 3 1 2 0 0 1 1 < 3>

Examples: Absolute Lo, unbalanced 4 1 2 0 1 0 0 < 4>

Alarm 1 (40018): Deviation Hi 5 2 0 1 0 1 < 5>
Stand-by off, Latch on = 0 0 0 1 <1 > Deviation Lo 6 2 0 1 1 0 < 6>
Absolute Lo, Balanced = 0 0 1 0 < 2>
<1 2> Band Outside 7 2 0 1 1 1 < 7>
Alarm 2 (40014): Band Inside 8 2 1 0 0 0 < 8>
Stand-by on, Latch off = 0 0 1 0 <2 >
Band Outside = 0 1 1 1 < 7> See Setpoint Alarm Figures, Page 5, for illustrations of alarm operation.
<27>

COMMUNICATIONS REGISTER (40026) AND COILS 1-8 TABLE

Coil 8 Coil 7 Coil 6 Coil 5 Coil 4 Coil 3 Coil 2 Coil 1 Coil 8 =0 Coil 8 =1
Mode Parity Baud
B7* B6 B5 B4 B3 B2 B1 B0 HEX HEX
RTU 8N1,2 300 0/1 0 1 0 0 0 0 0 <20> <A0>
RTU 8N1,2 600 0/1 0 1 0 0 0 0 1 <21> <A1>
RTU 8N1,2 1200 0/1 0 1 0 0 0 1 0 <22> <A2>
RTU 8N1,2 2400 0/1 0 1 0 0 0 1 1 <23> <A3>
RTU 8N1,2 4800 0/1 0 1 0 0 1 0 0 <24> <A4>
RTU 8N1,2 9600 0/1 0 1 0 0 1 0 1 <25> <A5>
RTU 8N1,2 19200 0/1 0 1 0 0 1 1 0 <26> <A6>
RTU 8N1,2 38400 0/1 0 1 0 0 1 1 1 <27> <A7>
RTU 8E1 300 0/1 0 1 0 1 0 0 0 <28> <A8>
RTU 8E1 600 0/1 0 1 0 1 0 0 1 <29> <A9>
RTU 8E1 1200 0/1 0 1 0 1 0 1 0 <2A> <AA>
RTU 8E1 2400 0/1 0 1 0 1 0 1 1 <2B> <AB>
RTU 8E1 4800 0/1 0 1 0 1 1 0 0 <2C> <AC>
RTU 8E1 9600 0/1 0 1 0 1 1 0 1 <2D> <AD>
RTU 8E1 19200 0/1 0 1 0 1 1 1 0 <2E> <AE>
RTU 8E1 38400 0/1 0 1 0 1 1 1 1 <2F> <AF>
RTU 8O1 300 0/1 0 1 1 1 0 0 0 <38> <B8>
RTU 8O1 600 0/1 0 1 1 1 0 0 1 <39> <B9>
RTU 8O1 1200 0/1 0 1 1 1 0 1 0 <3A> <BA>
RTU 8O1 2400 0/1 0 1 1 1 0 1 1 <3B> <BB>
RTU 8O1 4800 0/1 0 1 1 1 1 0 0 <3C> <BC>
RTU 8O1 9600 0/1 0 1 1 1 1 0 1 <3D> <BD>
RTU 8O1 19200 0/1 0 1 1 1 1 1 0 <3E> <BE>
RTU 8O1 38400 0/1 0 1 1 1 1 1 1 <3F> <BF>

* When reading register 40026, B7 will be a 0. When writing (changing ITMS communications to the new setting), change B7 to a 1.

13
 COMMUNICATIONS REGISTER (40026) AND COILS 1-8 TABLE (continued)
Coil 8 Coil 7 Coil 6 Coil 5 Coil 4 Coil 3 Coil 2 Coil 1 Coil 8 =0 Coil 8 =1
Mode Parity Baud B7 * B6 B5 B4 B3 B2 B1 B0 HEX HEX
ASCII 7N2 300 0/1 1 0 0 0 0 0 0 <40> <C0>
ASCII 7N2 600 0/1 1 0 0 0 0 0 1 <41> <C1>
ASCII 7N2 1200 0/1 1 0 0 0 0 1 0 <42> <C2>
ASCII 7N2 2400 0/1 1 0 0 0 0 1 1 <43> <C3>
ASCII 7N2 4800 0/1 1 0 0 0 1 0 0 <44> <C4>
ASCII 7N2 9600 0/1 1 0 0 0 1 0 1 <45> <C5>
ASCII 7N2 19200 0/1 1 0 0 0 1 1 0 <46> <C6>
ASCII 7N2 38400 0/1 1 0 0 0 1 1 1 <47> <C7>
ASCII 7E1 300 0/1 1 0 0 1 0 0 0 <48> <C8>
ASCII 7E1 600 0/1 1 0 0 1 0 0 1 <49> <C9>
ASCII 7E1 1200 0/1 1 0 0 1 0 1 0 <4A> <CA>
ASCII 7E1 2400 0/1 1 0 0 1 0 1 1 <4B> <CB>
ASCII 7E1 4800 0/1 1 0 0 1 1 0 0 <4C> <CC>
ASCII 7E1 9600 0/1 1 0 0 1 1 0 1 <4D> <CD>
ASCII 7E1 19200 0/1 1 0 0 1 1 1 0 <4E> <CE>
ASCII 7E1 38400 0/1 1 0 0 1 1 1 1 <4F> <CF>
ASCII 7O1 300 0/1 1 0 1 1 0 0 0 <58> <D8>
ASCII 7O1 600 0/1 1 0 1 1 0 0 1 <59> <D9>
ASCII 7O1 1200 0/1 1 0 1 1 0 1 0 <5A> <DA>
ASCII 7O1 2400 0/1 1 0 1 1 0 1 1 <5B> <DB>
ASCII 7O1 4800 0/1 1 0 1 1 1 0 0 <5C> <DC>
ASCII 7O1 9600 0/1 1 0 1 1 1 0 1 <5D> <DD>
ASCII 7O1 19200 0/1 1 0 1 1 1 1 0 <5E> <DE>
ASCII 7O1 38400 0/1 1 0 1 1 1 1 1 <5F> <DF>
ASCII 8N1 300 0/1 1 1 0 0 0 0 0 <60> <E0>
ASCII 8N1 600 0/1 1 1 0 0 0 0 1 <61> <E1>
ASCII 8N1 1200 0/1 1 1 0 0 0 1 0 <62> <E2>
ASCII 8N1 2400 0/1 1 1 0 0 0 1 1 <63> <E3>
ASCII 8N1 4800 0/1 1 1 0 0 1 0 0 <64> <E4>
ASCII 8N1 9600 0/1 1 1 0 0 1 0 1 <65> <E5>
ASCII 8N1 19200 0/1 1 1 0 0 1 1 0 <66> <E6>
ASCII 8N1 38400 0/1 1 1 0 0 1 1 1 <67> <E7>
ASCII 8E1 300 0/1 1 1 0 1 0 0 0 <68> <E8>
ASCII 8E1 600 0/1 1 1 0 1 0 0 1 <69> <E9>
ASCII 8E1 1200 0/1 1 1 0 1 0 1 0 <6A> <EA>
ASCII 8E1 2400 0/1 1 1 0 1 0 1 1 <6B> <EB>
ASCII 8E1 4800 0/1 1 1 0 1 1 0 0 <6C> <EC>
ASCII 8E1 9600 0/1 1 1 0 1 1 0 1 <6D> <ED>
ASCII 8E1 19200 0/1 1 1 0 1 1 1 0 <6E> <EE>
ASCII 8E1 38400 0/1 1 1 0 1 1 1 1 <6F> <EF>
ASCII 8O1 300 0/1 1 1 1 1 0 0 0 <78> <F8>
ASCII 8O1 600 0/1 1 1 1 1 0 0 1 <79> <F9>
ASCII 8O1 1200 0/1 1 1 1 1 0 1 0 <7A> <FA>
ASCII 8O1 2400 0/1 1 1 1 1 0 1 1 <7B> <FB>
ASCII 8O1 4800 0/1 1 1 1 1 1 0 0 <7C> <FC>
ASCII 8O1 9600 0/1 1 1 1 1 1 0 1 <7D> <FD>
ASCII 8O1 19200 0/1 1 1 1 1 1 1 0 <7E> <FE>
ASCII 8O1 38400 0/1 1 1 1 1 1 1 1 <7F> <FF>

* When reading register 40026, B7 will be a 0. When writing (changing ITMS communications to the new setting), change B7 to a 1.

14
This page intentionally left blank

15
 LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained
herein and relies on no other warranties or affirmations.

Red Lion Controls AP

Red Lion Controls Red Lion Controls BV 31, Kaki Bukit Road 3,
20 Willow Springs Circle Basicweg 11b #06-04/05 TechLink
York PA 17406 NL - 3821 BR Amersfoort Singapore 417818
Tel +1 (717) 767-6511 Tel +31 (0) 334 723 225 Tel +65 6744-6613
Fax +1 (717) 764-0839 Fax +31 (0) 334 893 793 Fax +65 6743-3360