GPS Tracker Software Platform User Manual Content

I.Preparation ............................................................................................................................................................................................1 II. Manual track on google earth .............................................................................................................................................................1 III. Track on PDA & cell phone ..............................................................................................................................................................1 IV. Get location in real street/address name by cell phone. .....................................................................................................................2 V. Track on Web-based Monitor Center by GPRS ..................................................................................................................................2 VI. Track on PC Installation monitor Software in CD by GPRS. ...........................................................................................................5

I. Preparation
Load a GSM SIM card into the tracker and subscribe the GPRS service. Please make sure that the SIM card is able to execute the function of incoming calls display, no calls can be diverted and the PIN code is locked. And switch the tracker on.

II. Manual track on Google Earth

2.1 Dial the SIM card number in tracker, it will hang up and reply a SMS with http link and real-time latitude and longitude automatically.

2.2. Install the software

in CD in your pc, and open google earth, type the lat/long. from SMS in your cell phone

replied from tracker on the blank of google earth,

and click OK to get the detailed position of target tracker. As shown

III. Track on PDA & cell phone

3.1 The SMS received from tracker including an http link, enter the link through your PDA or cell phone to get the detailed position anywhere and anytime. As shown below:

3.2. PDA or cell phone for this function must/support pictures viewing/and internet capability.

IV. Get location in real street/address name by cell phone.

4.1 You must set up the APN of your local GSM network for the SIM card in tracker first before using this function, if there is user name and password for GPRS login, Please refer to 5.3 and 5.4 to configure the APN, user name and password for GPRS login. 4.2 After configure the APN, send address+password to device, it will reply SMS including real street/address name. For example: No.113, Nantou Guankou 2nd Rd. Nanshan district, Shenzhen, Guangdong, china.

V. Track on Web-based Monitor Center by GPRS

5.1. The default APN, IP & Port (Default APN is CMNET; IP is 202.104.150.75 5.2. Obtain IMEI Number 5.2.1 Switch the GPS tracker on, text the tracker a SMS imei123456 via a cell phone, (123456 is the default password, If you changed the password, pls send SMS with new 6 digits password),a imei number in 15 digits will be return to your cell phone. port is 9000)

5.2.2. All trackers active for tracking on web based monitor center when depart from factory with 7 days free time. If you want to continue after 7 days, please send your IMEI to us, we will active it for one years after your payment, and pay again next year.
5.3. APN Configuration 5.3.1. APN standards for Access Point Name and differs from country to country. For more information about the local APN, inquire with your local GPRS network operator. 5.3.2. Text the tracker a SMS APN123456 + Space +APN of your local GSM net operator via a cell phone after obtaining your correct APN, and if succeeded in setup, the tracker will return the message APN OK e.g. send SMS command apn123456 cmnet to tracker device, If succeeded, APN OK is returned by the tracker in SMS. Notes: 123456 refers to password of tracker and CMNET is the APN of China Mobile (One of GSM network operator in china).

5.4. GPRS Login User Name and Password Configuration 5.4.1 In most countries, the user name and password involving GPRS login are not compulsorily necessary. Therefore, the entry can be skipped. For those countries requiring user name and password, please configure as follows: 5.4.2 Send SMS command up+123456+Space+User+Space+Password. If succeeded, user, password OK is returned by the tracker in SMS. E.g. Send SMS up123456 Jonnes 666666 to the tracker, and if succeeded, the tracker returns "user, password OK". Notes: 123456 refers to password of the tracker, Jonnes user name and 666666 GPRS password.

5.5IP Address and Port Setup 5.5.1 Send SMS as below via a cell phone: adminip+123456+Space+IP Address+Space+Port Number. The configuration for all subscribers in our

web-server monitor center should with our unique IP and port. IP is: 202.104.150.75 port is: 9000. So the SMS command sent by cell phone as following: adminip123456 202.104.150.75 9000 If configuration goes smoothly, the tracker returns "adminip OK"

5.6 Modes switch between SMS and GPRS 5.6.1 Send SMS GPRS+password to the unit, and it will reply GPRS ok! and switch to GPRS mode. 5.6.2 Send SMS SMS+password to the unit, it will reply SMS ok! and restore to SMS mode.
5.7. Sign up user ID and password Enter www.gpstrackerxy.com , click register, setting up a user ID and password and save, and be sure to keep the user ID and password in mind.

5.8Add IMEI Number

Sign in the system with your user ID and password; add IMEI number in menu of terminal management

5.9. Control command operation

5.9.1. Clicking the terminal (IMEI) you added in terminal list, the upper side of the map.

and then you can manage all the terminals by clicking the menu on

5.9.2 Real time tracking, please click 5.9.3 Cancel tracking, please track 5.9.4 Setting up movement alarm, please click

; and choose intervals as 10S or 20S. . .

5.9.5 Setting up over speed alarm, please click 5.9.6 Cancel alarms, please click

. , click this menu to cancel all alarms.

5.9.7 Setting up terminal time, please click 5.9.8 Cut off the oil and power system, please click operating with caution to avoid dangerous. 5.9.9 Resume the oil and power system, please click

. , this function is only for vehicle GPS tracker; please

, this function is only for vehicle GPS tracker.

5.9.10 ARM, please click 5.9.11 DISARM, please click

, this function is only for vehicle GPS tracker. , this function is only for vehicle GP tracker.

5.9.12 Trace Playback, please click click play.

, select the time period you want to check

, click search and then

5.9.13 Alarm and tracking history, please click

5.9.14. Account password modification, please click

5.9.15. Add sub-account, please click

5.9.16. Manage sub-account, you can assign trackers to sub-accounts and set up permissions.

5.9.17 Switching the mode from GPRS into SMS, please send SMS command SMS+password to tracker via your cell phone, it will reply SMS OK and restore to SMS mode.

VI. Track on PC Installation monitor Software in CD by GPRS.

6.1. Your pc is a mini server, and dont restrict any mid-server operator, the software in one computer can monitor 255 target trackers at most, GPRS data transfer through pc to tracker device real time. the operation steps as following: 6.2. IMEI checking:

Send SMS command "imei+password" to the unit. E. g.: Send SMS command "imei123456" to the unit, a IMEI number in 15 digits will be returned to your cell phone. 6.3. Setting up APN 6.3.1 APN standards for Access Point Name and differs from country to country. For more information about the local APN, inquire with your local GPRS network operator. 6.3.2 Text the tracker a SMS APN123456 + Space + your local APN via a cell phone and if succeeded in setup, the tracker will return the message APN OK. 6.3.3 e. g. Send SMS command APN123456 CMNET. If succeeded, APN OK is returned by the tracker in SMS. Notes: 123456 refers to password of tracker and CMNET is the APN of China Mobile( one of GSM network operator in china.)
6.4 GPRS Login User Name and Password Configuration 6.4.1 In most countries, the user name and password involving GPRS login are not compulsorily necessary. Therefore, the entry can be skipped. For those countries requiring user name and password, please configure as follows: 6.4.2 Send SMSup + 123456 + Space + User + Space + Password. If succeeded, user, password OK is returned by the tracker in SMS. 6.4.3 For instance, send SMSup123456 Jonnes 666666 to the tracker, and if succeeded, the tracker returns user, password OK

Notes: 123456 refers to password of the tracker, Jonnes user name and 666666 GPRS password. 6.5 IP Address and Port Setup 6.5.1. Send SMS as below via a cell phone: adminip + 123456 + Space + IP Address + Space + Port Number. If succeeded, adminip OK is returned by the device in SMS. 6.5.2 For example, send SMS command "adminp123456 21.34.116.58 7070" to the tracker. If configuration goes smoothly, the tracker returns "adminip OK"; If there is something wrong then SMS adminip fail is received, check out the format of commands sent and password as well. Note: 123456 refers to password, 21.34.116.85 IP address of the public network to which the computer installed the monitor center software pertains, 7070 the port receiving GPRS data of the monitor center software. The above mentioned port corresponds to an idle computer port. 6.5.3. How to obtain a public IP address? 6.5.3.1 For ADSL subscribers with routing function disenabled, right-click the My Network Place in the Windows NT/2000/2003/XP, click Properties and then select Local Connection in the subsequently popped up window for network connection. At this movement, your public IP address appears in the left lower corner. 6.5.3.2 For ADSL subscribers with routing function enabled, the current IP address refers to an internal IP address such as 192.168.1.103 is internal subscribers. In order to obtain a public IP address, it is required first of all to find out the IP address of the router (the router IP address is a proprietary IP address rather than a public IP address). Type in the router IP address into the location field of the IE explorer and then log into the configuration interface of the router following entering the user name and password of the router. Due to different manufacturers, the router configuration interface may differ from each other. It is strongly recommended you to read through the users manual of router. Attention: As your public IP address is not fixed but dynamic, it changes each time when surfing the internet via dial-up internet access, thus directly resulting in failure of GPRS connection. In such a case, it needs to set up current IP address via following the Step III. If your IP address is fixed, there is no need to consider troubles mentioned before and once set up, it can remain valid for a long-term. 6.5.4 Which are ports that can be configured? They range from 1024 to 65535 in number and are not allocated to certain service without alteration, this is to say, many services can use one port. Deploy the command Netstat in the Windows 2000/XP/Server 2003 to examine ports in use. Click Start/Run in turn and then put cmd into the field to open the command prompt symbol window. Type in netstat a -n and then press Enter to display the number and status of port in connection with TCP and UDP in the format of digits

All the ports displayed in the interface are occupied and not available for use. Select any number within the range of 1024~65535 other than those numbers displayed in the interface.

6.5.5 Attention: The ports in the tracker, router and system setup of the map monitor center should be identical. 6.6. Modes switch between SMS and GPRS 6.6.1 Send SMS GPRS+password to the unit, and it will reply GPRS ok! and switch to GPRSmode. 6.6.2 Send SMS SMS+password to the unit, it will reply SMS ok! and restore to SMS mode. 6.7. Router Port Mapping Method 6.7.1 For ADSL subscribers with routing function disenabled, there is no need for port mapping. 6.7.2 For internal subscribers surfing the internet via ADSL router automatic dial-up or co-shared internet access, it is compulsory to map ports. 6.7.3. What is necessity for port mapping? Lets focus on how GPS data in the tracker to transfer to the personal computer with the monitor platform software installed.

The tracker transfers GPS information to the network operator's machine room via GPRS first of all. Through wireless network, the GPS information is sent to internet and then a public IP associated with the router. The personal PC is connected with the internal network allocated by the router. In order to realize transferring GPS information to a personal PC correctly, the router must be able to transfer information received from WAN to the PCs in a LAN. 6.7.4 . In the first place, open the IE explorer and type in the router IP address in the address column. This IP address refers to neither a non-public IP IP in the personal PC but the router IP address which can be obtained from the users manual of router. nor

Enter the IP address mentioned above and then

put the default user name and password as well into the password entry dialogue box shown up subsequently. The user name and password can be found in the users manual of router. Log into the router configuration interface and find out the option of port mapping or transfer protocol. Set up the transfer port according to the tracker port configuration. Put in 7070 and then the internal IP address for information transfer. For example, enter 192.168.1.10 192.168.1.10 is the internal IP address for the computer where the monitor center software is installedand select TCP or ALL as protocol. Click Save and quit. The configuration is done at this point. 6.7.5 The following takes ALCATEL511 as an example to demonstrate how to map a port.

6.7.5.1 Open the IE explorer and enter 10.0.0.138 (IP address of ALCATEL511's Control Interface) into the address column. When the IP address is typed
incorrectly, IE displays corresponding information about the built-in control interface of ALCATEL511 as shown below.

6.7.5.2 When logging in, the basic interface of ALCATEL511 appears and then click the column ADVANCED in the left of the screen

An interface pops up subsequently. Here we can set up the port mapping function. Click NAPT in the left menu.

6.7.5.3 Although the router operation interface differs from manufacturer to manufacturer, the function of transfer or mapping is common for various
routers. If unable to complete configuration alone, seek for technical support from network technicians or router manufacturers.

Following NAPT control interface login, an interface shown above appears and some fields must be filled out.

6.7.5.4 Select the TCP mode and then enter 10.0.0.1 into the column of Internal IP that is identical to that in the PC. Type in 7070 into the fields in connection with Inside Port and Outside Port respectively. When configuration is done, click Apply to save.

Finally, click Save All in the left upper corner of the screen to save those settings. All the configuration information is stored in the firmware of ALCATEL511 and remains retained when no power is supplied to the ALCATEL511. However, the configuration information gets lost in the process of setting up router or updating firmware. When configuration is over, the port mapping function of ALCATEL511 ADSL adapter is available following reboot

6.8 Map can be installed subsequently, monitor software run in the circumstance of Windows NT/2000/2003/XP

6.9Click

in the CD ROM to initiate installation that only takes several minutes.

6.10Click

on the desktop following installation and then log in.

6.11 6.12Click Login to enter the map interface.

Type admin and admin as the default user ID and password as shown above.

6.13Right-click Terminal List and select Add Groups to add a group. When a certain group is chosen, click Add Group Branches to

supplement a sub-group. Select the ideal sub-group and click Add Terminal. The following window pops up instantly.

Type in the terminal IMEI number in the field of Terminal ID, then click Save to store the users information filled out as shown in figure. AttentionEach trackers IMEI number is unique and can only be allowed to add and use in one computer exclusively which means once such a number is added in one computer successfully, it is not allowed to be added into another computer. If the case of adding the IMEI number via another computer is inevitable, please contact your supplier or dealer and give your IMEI for assistance, then you can add the IMEI in any computer to operate after getting our authorized confirmation.

6.14. System Port Number Configuration: Click

and Select a current valid IP in personal computer in the server

field, 0 is invalid IP. type in a port number identical with the number of a mapping port in the terminal and router as well in point NO.field. and click Save to save ultimately

Attention: The corresponding system IP will be changed when you use the wired router, wireless router and wireless network card. IP will be shown in server field automatically, you only need to select one valid IP. If you the monitor software in the running status, pls stop running to change the IP address, it will be valid after changing and saving the system IP address.

6.15. Click

to launch the monitor map software. Operation can only be made after 1 minute following software opening as the GPRS connection takes around 1 minute to complete.

6.16. . Select a terminal in the Terminal List as shown below to check out. As shown below:

6.17. Single Locating: Click

to load the terminal control window and click Single Track to execute the mentioned

function once.

The following window displays information like name, latitude and longitude of the terminal being located and the map skips to the location where the terminal locates, namely, the place indicated by the red point in the map as shown below.

Plain Map

Hybrid Map

Satellite Map

6.18. Multiple Locating: Click Multi-track to select an interval from options including 10s, 15s, 20s, 30s, 1m, 5m, 10m, 30m, 1h, 5h,

10h and 24h to execute the said function.

6.19. Multi-track Cancellation: Click Cancel Multi-track to disenable the function of Multi-track and the message "Multi-track

Cancellation OK" appears in the column of Alarm Code if succeeded.

6.20. Alarm Halt: Click Stop Alarm to disenable all the alarm tasks being selected and the message "Stop Alarm OK" appears in

the column of Alarm Code if succeeded.

6.21. Move Alarm: Click move Alarm to enable the said function. Once the terminal is moved outside the 200m range as the

function in question is available, the corresponding alarm will be sent to the monitor center in every 3m. To disenable the said function, click stop alarm.
6.22. Overspeed Alarm: Fill out the column of Speed Limitation with a value between 10~300 and then click Overspeed Alarm to

send this command. When the terminal speed exceeds such a preset value, the corresponding alarm will be sent to the monitor center in every 3m. To disenable the said function, click stop alarm.
6.23. Time Change: Click Terminal Time to change GPS time to the local time. 6.24. SOS: When SOS is required, press and hold Tracker SOS for at least 3s and the terminal will send SOS information to

the monitor center every 3m accompanied by beeps. To disenable the said function, click Stop Alarm.

6.25. Group Management: Select an established group from the Terminal List drop-down list box and then click the right button.

Users are allowed to add a new IMEI number or edit/delete the said group etc. as shown below:

6.26. Terminal Management: Select an established terminal from the Terminal List drop-down list box and then click the right button.

Users are allowed to modify the terminal/check out alarm records/add or remove terminals etc. as shown below:

6.27. Trace Playback: Click Route Repeat to operate.

6.28. Manual Locating: Click Manual Track to operate.

6.29. Password Modification: Change the monitor center login password via Quit System.

6.30. Operation Interruption: Click Stop Receiving to terminate the data receiving process of the monitor center.

6.31. One monitor center can several port at the same time, but the map only display one current position of port.pls select the port

you want from terminal list If you want to check the position of another current port. 6.32. Multiple Locating function only used for one port for one time, If you want to Multi-track for another port, please cancel the multiple location function for the first port.
6.33. Switching the mode from GPRS into SMS, please send SMS command SMS+password to tracker via your cell phone, it will reply SMS OK and restore to SMS mode.