Scribd
Upload
15 views3 pages

Module 0

The document outlines a technical training course for Cummins authorized technicians focused on HHP natural gas engine and genset controls using PowerCommand® 3.3. It aims to equip participants with skills for servicing, troubleshooting, and configuring gas genset control systems. The course is intended for individuals with prior knowledge of related technical materials and includes various modules covering safety, genset controls, engine controls, and service tools.

Uploaded by

agvass
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views3 pages

Module 0

The document outlines a technical training course for Cummins authorized technicians focused on HHP natural gas engine and genset controls using PowerCommand® 3.3. It aims to equip participants with skills for servicing, troubleshooting, and configuring gas genset control systems. The course is intended for individuals with prior knowledge of related technical materials and includes various modules covering safety, genset controls, engine controls, and service tools.

Uploaded by

agvass
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

CUMMINS CONFIDENTIAL

Technical Training

Our energy working for you. ™

HHP Natural Gas Engine & Genset Controls


With PowerCommand® 3.3

C1000 N6C
C1100 N6C
C1250 N6C
C1400 N6C
C1750 N6C
C2000 N6C
C995 N5C
C1160 N5C
C1370 N5C
C1400 N5C
C1540 N5C
C1570 N5C
C1750 N5C
C2000 N5C
Course Objective
The purpose of this course is to educate Cummins authorized DFSE’s, Service Engineers and Technicians with a
foundation of familiarity and broad system knowledge to successfully develop, at site, skills needed to conduct the
following tasks on HHP gas genset control systems:
• Service, Troubleshooting & Repair
• Detail Configurations, Setups & Control Features
• Identify Different Modes of Site Operation

With this information, our technical force will be better prepared to meet our customers’ varying needs.

Course Audience
The primary audience for this course is Cummins Power Generation distributor technicians, DFSE’s and service
engineers. We assume the student’s of this course have prior familiarization of the following materials:

• (CMT6068) PC3.3 (Paralleling) Phase 1 (optional)


• (CVC 091824) Fundamentals of Natural Gas
• (CVC 0441) HHP NG Lean Burn Control Systems
• (PGU CMT0449) Utility Paralleling
• (PGU CMT6035) InPower Pro Familiarization
• (PGU CMT0694) Electrical Safety (Medium Voltage)
• (PGU CMT0134) Electrical Safety (Low Voltage)
• (CVC 1003) Introduction to Electrical Troubleshooting
• (CVC 1004) Basic Electrical Theory
• (CVC 1005) Digital Multimeter Usage
• (CVC 1006) Electrical Circuits
• (CVC 1008) Electronic Control System Inputs
• (CVC 1009) Electronic Control System Processors
• (CVC 1010) Electronic Control System Outputs
• (CVC 1011) Electronic Control System Identification
• (CVC 1012) Electrical Diagrams
• (CVC 1013) Electrical Wiring
• (CVC 1014) Multiplexing
• (CVC 1015) Troubleshooting Techniques for Electronic Control Systems
• (CVC 1027) InSite – Windows Familiarization
• (CVC 1028) InSite – Registration & Functionality
• (CVC 1029) InSite - Operation
• (CVC 1030) InSite – Read & Reset Fault Codes
• (CVC 1031) InSite – Diagnostic Operation
• (CVC 1032) InSite – Reading & Adjusting Features & Parameters
• (CVC 1033) InSite – ECM Calibration
• (CVC 1034) InSite – Multimodule Calibration
• (CVC 1035) InSite – ECM Data
• (CVC 1036) InSite – Work Orders
• (CVC 1037) InSite – Printing & File Manipulation
Table of Contents / Course Agenda:
Module 1: Introduction

Module 2: Safety & Isolation

Module 3: Genset Controls

Module 4: Engine Controls

Module 5: HMI’s

Module 6: Service Tools

Revision History:
March 27, 2009: Draft Complete

You might also like