History

Date Version Name Issue Link

Dec192022 TaiM Create UI Spec
Mar282023 TaiM Change function name Charging System Analysis
Apr052023 TaiM Update Spec check BLE and enable Battery VCI Service
Apr142023 TaiM Update Spec Battery Health Check, Charging System Analysis and Submit
May122023 TaiM Update Spec to perform function Battery Service
Jan022024 TaiM Update Some screens
Jan222024 HoangN Update LED Logic
Jan242024 HoangN Update LED Logic for USB mode
Aug 052024 HoangN Update specs SDS43 pair with Battery Tester Module
Aug282024 HoangN Add Memory Mode UI
 Battery Tester Module - SDS43
X0.05 Pair July 30 2024

SDS43 power from DLC Cable or Internal

batteries AA

BLE
 Battery Tester Module - SDS43
X0.05 HomeScreen July 30 2024

From
From
Vehicle
Button Home
Selection

To To To To To To To
OBD2 Diagnostics Previous Vehicles Workshop Tools Tool Library Settings OEM Diagnostics Battery Service
 Battery Tester Module - SDS43
X0.05 LED LOGIC July 30 2024

Start

Has Battery Tester module's Clamp been

NO
connected to Battery terminals?

Intervals: 0.5s On – 0.5s OFF until

LED: OFF
YES
connected

RED : Blink
Check in whole process, whenever BLE
disconnected or USB disconnect, LED
NO must blink
YES

Has battery tester module been

connected to SDS tool via BLE mode?

YES

All LED OFF

Depend on the test result of the

function. LED Status applies for both
Has function completed SDS tool and Battery Tester module
and need LED to show
the test result?

Yes YES

LED Status: ON

NO

Is the user going out of

the result screen?
 Battery Tester Module - SDS43
X0.05 BLE Connect July 30 2024

From
Battery Service

Need create QR code to link to the

Battery Tester Module
pro.repairsolution.com
2.5
Battery Service
Precautions:
Connect the Battery Tester Module clamps to the battery terminals
before performing this test.
Do not shut down or remove power from your Diagnostic Tool during
the test process.

Note: A Battery Tester Module is required to perform this test.

Scan the QR code below for more information.

Back Continue

Continue

From
Start: Scan available
"Retry" button
Battery Tester Module when losing BLE

2.6
Battery Service

Searching for Battery Tester Module

One moment please...

BACK

The latest BLE address device is

Show BLE address has been found highest priority to auto-connect
2.7
Battery Service

Available devices BLE Address

Battery Tester Module AA:BB:CC
To EXIT Is there a closest connected BLE
Battery Tester Module BB:DD:EE NO
HomeScreen address?
...

Back Exit
YES (auto connect)

Select a device

2.8

Battery Service

Pairing …

To
Is BLE connection successful? YES Battery Service

NO

2.9

Battery Service
EXIT
Retry
Couldn’t pair with Battery
Tester Module.
Exit Retry
 Battery Tester Module - SDS43
X0.05 Battery Service July 30 2024

From
Home Screen

Has battery tester module

NO been connected to SDS tool
via BLE mode?

From
BLE Connection
Battery Service icon located at YES
second page Home screen

Battery Service icon located at

2.4 2.1
Home Screen Home Screen first page Home screen
OBD2 Diagnostics OBD2 Diagnostics
OEM Diagnostics OEM Diagnostics
Workshop Tools Workshop Tools
Previous Vehicles Battery Service
Settings Previous Vehicles
Support Settings
Battery Service Support

Battery Service

Battery Service

Has Battery Tester

To
Module been connected NO BLE Connection
to SDS43 ?

YES

Is OBD cable
NO
connecting to DLC ? Check Global OBD2 and Only show DTC for the list below:
P0514 Battery Temperature Sensor Circuit Range/Performance
P0515 Battery Temperature Sensor Circuit
P0516 Battery Temperature Sensor Circuit Low
To
P0517 Battery Temperature Sensor Circuit High
Vehicle Vehicle P0620 Generator Control Circuit
No
confirmed? Selection P0621 Generator Lamp/L Terminal Circuit
P0622 Generator Field/F Terminal Circuit
P0623 Generator Lamp Control Circuit
P0625 Generator Field/F Terminal Circuit Low
P0626 Generator Field/F Terminal Circuit High
Yes
P063A Generator Voltage Sense Circuit
P063B Generator Voltage Sense Circuit Range/Performance
P063C Generator Voltage Sense Circuit Low
2.10 P063D Generator Voltage Sense Circuit High
Battery Service P065A Generator System Performance
P065B Generator Control Circuit Range/Performance
One moment please…
P065C Generator Mechanical Performance
P0A1A Generator Control Module
P2500 Generator Lamp/L-Terminal Circuit Low
P2501 Generator Lamp/L-Terminal Circuit High
P2502 Charging System Voltage
2.11
P2503 Charging System Voltage Low
Battery Service P2504 Charging System Voltage High

PXXXX (X/Y) <DTC Type>

DTCs Definition here if available. Are there DTCs belong to
Yes
WARNING: that list?
A related fault code has been retrieved,
please refer to the appropriate service
information before continuing.
Continue
No/not support

Is this
Continue Hybrid/Electric
YES
Vehicle?

No

2.12
2.3 Battery Service
Battery Service 2.16
Select and press <enter>
Select and press <enter>
Battery Health Check Battery Health Check Battery Service
Starter System Test Starter System Test
Charging System Analysis Charging System Analysis Select and press <enter>
Electrical System Test Electrical System Test
Voltmeter Voltmeter EV/HEV/PHEV Battery Health
Battery Reset Procedures EV/HEV/PHEV Inspection
Battery Initialization Voltmeter
Battery Test Battery Live Data (12 Volt)
Battery Live Data (12 Volt)
Alternator Test
Alternator Live Data

Battery Clamps DLC cable

OBD

To
To To To To To To
To To To To To To EV/HEV/PHEV
Battery Health Charging System Electrical System Battery Reset Battery Live Data EV/HEV/PHEV
Starter System Test Voltmeter Battery Initialization Battery Test Alternator Test Alternator Live Data Inspection
Check Analysis Test Procedure (12V) Battery Health
(reserve)
 Battery Tester Module - SDS43
X0.05 function_BatteryHealthCheck() July 30 2024

Start

User input Rating:

Variable: CCAi

LOCAL NOTE:

SOC < 0% => Show: SOC = 0% Command read CCA

startCCATest
Variable: CCAm
SOC > 100% => Show: SOC = 100%

SOH > 100% => Show: SOH = 100%

minSOH is determined by mapping to the table

and take the lower value minSOH closest to the
calculatePact (unit: %)
batteryVoltage
Variable: Pact = (CCAm/CCAi)*100
All LED status only apply for BHC/ Out vehicle
(regarding to In vehicle - LED status depending on final
status combined)

getCurrentVoltage
getCurrentVoltage
Variable:batteryVoltage

NO ( <= 12.4) Is Battery Voltage > 12.4 ? YES (> 12.4)

AGM/GEL Is BatteryType == Flooded Is BatteryType == Flooded

AGM/GEL
or BatteryType == AGM/GEL ? or BatteryType == AGM/GEL ?

Flooded Flooded

calculateSOCValue(of AGM/GEL) unit: % calculateSOCValue (of Flooded) calculateSOCValue (of Flooded) calculateSOCValue(of AGM/GEL) unit: %

Variable:SOC = 88.649*batteryVoltage – 1041.4 Variable:SOC = 125*batteryVoltage - 1475 Variable:SOC = 125*batteryVoltage - 1475 Variable:SOC = 88.649*batteryVoltage – 1041.4

calculatePswi(of AGM/GEL) unit: % calculatePswi(of Flooded) calculatePswi(of Flooded) calculatePswi(of AGM/GEL) unit: %

Variable:Pswi= 100 – (-34.123*batteryVoltage + 457.77) Variable:Pswi = 100 – (-57.153*batteryVoltage + 738.08) Variable:Pswi = 100 – (-57.153*batteryVoltage + 738.08) Variable:Pswi= 100 – (-34.123*batteryVoltage + 457.77)

Is Pact > Pswi ? Is Pact > Pswi ? YES (Pact > Pswi) Is Pact > Pswi ?
YES (Pact > Pswi)

YES (Pact > Pswi)

Determine minSOH following table: Determine minSOH following table: NO (Pact < Pswi)
minSOH based on batteryVoltage and map to the table and take the
NO (Pact < Pswi) lower value minSOH closest to the batteryVoltage, minSOH based on batteryVoltage and map to the table and take the
NO (Pact < Pswi) lower value minSOH closest to the batteryVoltage,
eg. batteryVoltage = 12.57 => minSOH = 95
eg. batteryVoltage = 12.57 => minSOH = 95

calculatePswi2 (of AGM/GEL) calculatePswi2 (of Flooded) calculatePofPact (Position of Pact) calculatePofPact (Position of Pact)
Variable: Pswi2 = 100 - (-73.733*batteryVoltage + 976.76) Variable: Pswi2 = 100 - (-114.05*batteryVoltage + 1449) Variable: PofPact = (Pact - Pswi)/(100 - Pswi) Variable: PofPact = (Pact - Pswi)/(100 - Pswi)

calculateSOH (unit %) calculateSOH (unit %)

Variable: SOH = minSOH + (PofPact*(100-minSOH)) Variable: SOH = minSOH + (PofPact*(100-minSOH))

Is Pact < Pswi2 ?

NOTE: In case of testing in NO (Pact > Pswi2)

Electrical System Test, the Title
"Battery Health Check" should be
changed to "Electrical System
Test" at this screen

4.11 YES (Pact < Pswi2)

Battery Health Check

Select the charge state of the battery before

performing the test:

After charge Before charge

After Charge

Before Charge
NOTE: LED at this function just
applies for BHC/ Out of vehicle

Turn ON Turn ON
Turn ON Turn ON Turn ON LED GREEN LED RED
LED YELLOW LED RED LED GREEN

Do not calculate SOH Do not calculate SOH

Show: SOH: -- % Show: SOH: -- %

BATTERY RESULT: CHARGE-RETEST BATTERY RESULT: REPLACE BATTERY BATTERY RESULT: GOOD-RECHARGE BATTERY RESULT: GOOD BATTERY BATTERY RESULT: REPLACE BATTERY

End
 From
Battery Service
Battery Tester Module - SDS43
X0.05 Battery Health Check July 30 2024

Always check battery Connection in

whole test process.
4.1
Battery Health Check

Communication Failure
Is BLE still connected ? NO Please double-check the Bluetooth or
Battery Tester VCI clamp connection.

Retry Exit
YES
4.4
Battery Health Check
Charge the battery and RETRY EXIT
retest.
Is Vbatt > 11.8V
NO

To
YES Jump to screen To
Checking
2.6 Battery Service
3.14
BLE Connection
Battery Health Check

3.3 Battery In Vehicle Test Conditions:

Battery Health Check
Parking Brake is ON.
4.11
Transmission in PARK or NEUTRAL.
In Vehicle Test Turn the ignition in the Key ON, Engine OFF position. Battery Health Check
Place the headlights and blower motor in the OFF position.
Out of Vehicle Test For maintenance-type batteries: Check the electrolyte level. Does OBD2 cable Process:
Inspect the battery for damage or corrosion. Is battery voltage above Does PID (01 0C) Is PID YES Turn the engine OFF.
Out of vehicle test NO connected to YES Get VIN (if not yet) YES
In Vehicle Test 12.5 V ? supported ? RPM (01 0C) > 0 ? Turn the key to the ON position, do not start the
DLC ? OBD2 PID 01 0C engine.

Exit NO NO
YES
NO
Note: Do not perform this test on Smart Alternator, Hybrid and Electric vehicles
Does Vin
decoded ? NO
3.29
Back Continue 4.31
Battery Health Check
3.29 Battery Health Check
3.29 Battery Standard
Battery Health Check CCA Battery Health Check
Battery Type CA Enter the battery CCA value (on battery Vehicle selection
Check Surface Voltage... YES done
JIS label), then press OK to perform the test.
Flooded
DIN OK
AGM OK
GEL EN
DIN
Back SAE loop
NO
Back
4.31
Does Surface Voltage NO Vehicle Confirm
Detected? 2018 Ford F150 V6, 3.5L ?

Is this your vehicle ?

YES
4.31
Battery Health Check
Read Voltage (V1)
Testing battery health check ...

YES

11.2
Battery Health Check Does selected vehicle has
Battery Information
Surface voltage detected. Database ?
Turn the headlights and blower ON.
Process (func_BatteryHealthCheck):

measure CCA YES

calulate SOH Reservce (build later)
calulate SOC
Internal resistance 4.31
measure battery voltage Battery Health Check
NO
measure battery temperature 2018 Ford F150 V6, 3.5L
Please select the vehicle's battery
loop information

Option 1:
Battery Type: xx
Battery Standard: xx
Read Voltage (V2) Option select
Battery Rating: xx
CCA result to determine --
Battery Health Check Status Option 2:
NO
Return of: function_BatteryHealthCheck() Battery Type: xx
loop Battery Standard: xx
Battery Rating: xx
--
Not Listed

Is V2 < (V1 - 0.2) ?

NOT LISTED

Show result YES

3.29
Battery Health Check Process (func_BatteryHealthCheck):
3.29 Battery Standard 3.29
11.2 4.31
Battery Health Check CCA Battery Health Check measure CCA
Battery Health Check Enter the battery CCA value (on battery Battery Health Check
Battery Type CA calulate SOH
JIS label), then press OK to perform the test.
Turn the headlights and blower OFF. Flooded OK
calulate SOC
DIN OK Testing battery health check ...
AGM OK Internal resistance
GEL EN
DIN
measure battery voltage
Back SAE measure battery temperature

Continue Back
Continue

4.4 auto
Battery Health Check
Charge the battery and
retest.
Is Vbatt > 11.8V 4.5
NO Battery Health Check
30s countdown
The engine must be started within 30 seconds

RETEST
3.3
Battery Health Check
3.24 30
Battery Health Check
In Vehicle Test
Out of Vehicle Test
Cancel
Unable to perform the test.

Exit NO
Cancel Retest

Is dectect Start Signal within 30s

YES

Determine the Crank/drop Result following

table:

Combine:
1. CCA result [Battery Health Check Status]
Return of: function_BatteryHealthCheck()
2. Crank result to determine (table)
4.10
Battery Health Check
to determin the Final Battery Health Check Status
Turn the engine and all vehicle accessories OFF following Table:
Turn ON
LED depends Done
on Battery
Status

Done

Battery Standard
YES
= JIS ?

NO

3.27b
3.27b
BATTERY RESULT: <text result>
<status text description>
BATTERY RESULT: <text result>
<status text description>

State of Health (SOH): xxxx %

State of Charge (SOC): xxxx % State of Health (SOH): xxxx %
Measured: xxxx CCA State of Charge (SOC): xxxx %
Resistance: xxxx mΩ Measured: xxxx BBB
JIS NUMBER: xxxx xxxx CCA Resistance: xxxx mΩ
Battery type: xx Rating: xxxx BBB
Battery voltage: xx.xx V Battery type: xxxx
Battery temperature: xx.xx oC Battery voltage: xx.xx V
Battery temperature: xx.xx oC
REPAIR TIPS:
<text> REPAIR TIPS:
<text>
Report Complete
Report Complete

Report Report
Complete

Complete

To
Report Battery To
Service Battery Service
 Battery Tester Module - SDS43
X0.05 Starter System Test July 30 2024

From
Battery Service

Always check battery Connection in

whole test process.
4.1
Starter System Test

Communication Failure
Is BLE still connected ? NO Please double-check the Bluetooth or
Battery Tester VCI clamp connection.

Retry Exit
YES
4.4
Starter System Test
RETRY EXIT
Charge the battery and
retest.
Is Vbatt > 11.8V
NO

To
Exit
YES Jump to screen To
2.6 Battery Service
BLE Connection
checking

4.3
Starter System Test
Starter System Test conditions:
save vehicle infor to report 4.11
• Parking Brake is ON.
• Transmission is in PARK or NEUTRAL. Starter System Test
• Turn the ignition in the Key ON, Engine OFF position.
• Place the accessories in the OFF position and all doors are closed. Does OBD2 cable Process: Is PID Turn the engine OFF.
Continue connected to YES Get VIN (if not yet) YES
RPM (01 0C) > 0 ? Turn the key to the ON position, do not start the
DLC ? OBD2 PID 01 0C engine.
YES

NO

Does PID (01 0C)

Back Continue
support ?

NO

NO Is Vbatt > 11.8V NO

30s countdown

4.5
4.10
Starter System Test
Starter System Test
The engine must be started within 30 seconds
Turn the engine and all vehicle accessories OFF
Time out

30
Done

NO checking

DONE 4.6
STARTER SYSTEM RESULT: NO START
Is dectect Start Signal within 30s Not detect start engine.

Drop voltage: -- V To
Cranking voltage: -- V Battery Service
LED ON Starting time: -- ms Complete
YELLOW
YES

ALL LED OFF

Report Complete

4.10
Starter System Test
To
Turn the engine and all vehicle accessories OFF REPORT Report Battery
Service

4.7
Done STARTER SYSTEM RESULT: CRANKING NORMAL
Starter operation is normal.

Drop voltage: xx.xx V

Cranking voltage: xx.xx V
Starting time: xx.xx ms Complete

DONE

Report Complete

Is Vcrank > 10V ? LED ON REPORT

YES
(more than 10V)
GREEN

4.8
NO STARTER SYSTEM RESULT: CHARGE BATTERY
The starter voltage is low and the battery is not fully charged.

Drop voltage: xx.xx V

Cranking voltage: xx.xx V
Is 9.5V < Vcrank <= 10V ? YES
LED ON Starting time: xx.xxms
Complete
(more than 9.5 and less than or equal 10V)
YELLOW

NO
Report Complete

Is Vcrank V <= 9.5V ? LED ON REPORT

YES
(less than or equal 9.5V)
RED
4.9
STARTER SYSTEM RESULT: LOW VOLTAGE
Starter voltage is too low.

Drop voltage: xx.xx V

Cranking voltage: xx.xx V
Starting time: xx.xxms
Complete

Report Complete

REPORT
 Battery Tester Module - SDS43
X0.05 Charging System Analysis July 30 2024

From
Battery Service

Always check battery Connection in

whole test process.
4.1
Charging System Analysis

Communication Failure
Is BLE still connected ? NO Please double-check the Bluetooth or
Battery Tester VCI clamp connection.

Retry Exit
YES

RETRY EXIT

Is Vbatt > 11.8V

To
YES Jump to screen To
2.6 Battery Service
BLE Connection
checking

5.3
Charging System Analysis
Charging System Test Conditions: 4.11
Charging System Analysis
Parking brake is ON.
The engine of the vehicle must be running during the
Transmission is in PARK or NEUTRAL.
testing process.
Place the headlights and blower motor in the
Does OBD2 cable Process:
OFF position. Is PID
Continue connected to YES Get VIN (if not yet) NO
Start the engine. RPM (01 0C) > 0 ?
DLC ? OBD2 PID 01 0C
YES

Note: Please following the alternator test procedure for

NO NO safety and more accurate test results.
Note: Do not perform this test on Smart Alternator,
Hybrid and Electric vehicles Does PID (01 0C)
Continue supported ?
YES

4.4
Charging System Analysis
Charge the battery and
retest.
NO Is Vbatt > 11.8V NO

Is Vbatt > 11.8V

Exit NO

YES YES

5.4
Charging System Analysis 5.4
Charging System Analysis
Increase engine speed and maintain at
2000-3000 RPM, then press Continue. Increase engine speed and maintain at
2000-3000 RPM.

checking Is RPM > 2000 ?

Continue

xx RPM

2 command: 2 command: YES (delay 3s)

Get voltage (1.5s first) 5.5 Get voltage (1.5s first)
Get ripple (1.5s next) Charging System Analysis Get ripple (1.5s next) 5.5
Charging System Analysis

Testing charging system at engine RPM

with accessories OFF. Testing charging system at engine RPM
with accessories OFF.

5.6
Charging System Analysis 5.6
Charging System Analysis
Return engine to idle speed, then press
Continue. Return engine to idle speed, then press
Continue.

checking Is RPM < 2000 ?

Continue
XX RPM

2 command: 2 command: YES (delay 3s)

Get voltage (1.5s first) Get voltage (1.5s first)
5.7
Get ripple (1.5s next) Charging System Analysis Get ripple (1.5s next) 5.7
Charging System Analysis

Testing charging system at idle with

accessories OFF. Testing charging system at idle with
accessories OFF.

5.8
Charging System Analysis 5.8
Charging System Analysis
Turn the headlights and blower ON, then
press Continue. Turn the headlights and blower ON, then
press Continue.

Continue
Continue

2 command:
Get voltage (1.5s first) 2 command:
Get ripple (1.5s next) Get voltage (1.5s first)
5.9 Get ripple (1.5s next)
Charging System Analysis 5.9
Charging System Analysis

Testing charging system at idle with

accessories ON. Testing charging system at idle with
accessories ON.

5.10
Charging System Analysis 5.10
Charging System Analysis
Increase engine speed and maintain at NO
2000-3000 RPM, then press Continue. Increase engine speed and maintain at
2000-3000 RPM, then press Continue.

checking Is RPM > 2000 ?

Continue
XX RPM
2 command:
Get voltage (1.5s first)
Get ripple (1.5s next) 2 command: YES
5.11 Get voltage (1.5s first)
Charging System Analysis 5.11
Get ripple (1.5s next) Charging System Analysis

Testing charging system at engine RPM

with accessories ON. Testing charging system at engine RPM
with accessories ON.

5.12
Charging System Analysis

Turn the engine and all vehicle

accessories OFF, then press Continue.

Continue

Determine final test result

REPORT

5.13
CHARGING SYSTEM RESULT: GOOD
The charging system is good.

LOADED: x.xxV
NO LOAD: x.xxV
LED ON AC Ripple Voltage: x.xxmV
Final status = PASS
YES GREEN Continue

REPAIR TIPS:
Charging voltage is within specification.
Report Complete

REPORT

No
5.14
CHARGING SYSTEM RESULT: OUTPUT TOO HIGH
The charging voltage is above the acceptable limit.

LOADED: x.xxV
NO LOAD: x.xxV
AC Ripple Voltage: x.xxmV
Final status
LED ON
= OUTPUT TOO YES RED REPAIR TIPS:
Continue
HIGH Verify the ground connection is proper, if there are no
loose connections. Replace the voltage regulator or
replace the alternator it is equipped with a built-in
regulator.

Report Complete

REPORT
No
5.15
CHARGING SYSTEM RESULT: OUTPUT TOO LOW
Alternator not providing sufficient current to charge the battery and power
the vehicle′s electrical systems.

LOADED: x.xxV
NO LOAD: x.xxV
AC Ripple Voltage: x.xxmV
Final status LED ON
= OUTPUT TOO YES Continue
LOW
RED
REPAIR TIPS:
- Check the condition of the alternator drive belts. Verify the alternator
rotates while the engine running. Replace worn or slipping belts and
retest.
- Inspect all charging system connections, particularly the cable connection
to the battery. Clean the cable as needed. Replace the cable if damaged,
then retest.

Report Complete

REPORT
No

5.16
CHARGING SYSTEM RESULT: EXCESSIVE RIPPLE
An excessive amount of AC ripple voltage has been
detected.

LOADED: x.xxV
LED ON NO LOAD: x.xxV
Final status
AC Ripple Voltage: x.xxmV Continue
= EXCESSIVE
YES
RED
REPAIR TIPS:
- The diodes in the alternator are defective or the communication diodes
are damaged
- The stator is damaged

Report Complete

REPORT
No

5.17
CHARGING SYSTEM RESULT: NO OUTPUT
No alternator output detected.

LOADED: x.xxV
NO LOAD: x.xxV
LED ON AC Ripple Voltage: x.xxmV
Final status Continue
ALL LED OFF
= NO OUTPUT
YES
RED REPAIR TIPS:
- Inspect all charging system connections, particularly the cable connection at the
battery terminal. Clean the cable as needed. Replace the cable if damaged, then
retest.
- If the cable and belts are in good condition, replace the alternator or voltage
regulator.

Report Complete

To To
Battery Service Report Battery
Service
 Battery Tester Module - SDS43
X0.05 Electrical System Test July 30 2024
From
Battery Service

Always check battery Connection in

whole test process.
4.1
ELectrical System Test

Communication Failure
Is BLE still connected ? NO Please double-check the Bluetooth or
Battery Tester VCI clamp connection.

Retry Exit
YES
4.4
ELectrical System Test
Charge the battery and RETRY EXIT
retest.
Is Vbatt > 11.8V
NO

To
YES Jump to screen To
2.6 Battery Service
BLE Connection

3.14 Checking
Electrical System Test
Battery In Vehicle Test Conditions:

Parking Brake is ON.

Transmission in PARK or NEUTRAL. Back
Turn the ignition in the Key ON, Engine OFF position.
Place the headlights and blower motor in the OFF position.
4.11
For maintenance-type batteries: Check the electrolyte level. Electrical System Test
Inspect the battery for damage or corrosion.
Does OBD2 cable Process:
Is battery voltage above Does PID (01 0C) Is PID YES Turn the engine OFF.
Continue NO connected to YES Get VIN (if not yet) YES
12.5 V ? supported ? RPM (01 0C) > 0 ? Turn the key to the ON position, do not start the
DLC ? OBD2 PID 01 0C engine.

NO NO
YES
NO
Note: Do not perform this test on Smart Alternator, Hybrid and Electric vehicles Does Vin
decoded ? NO

Back Continue
4.31
Electrical System Test

Check Surface Voltage... Vehicle selection

YES done

loop
NO

4.31
Does Surface Voltage NO Vehicle Confirm
Detected? 2018 Ford F150 V6, 3.5L ?

Is this your vehicle ?

YES

Read Voltage (V1)

YES

11.2
Electrical System Test Does selected vehicle has
Battery Information
Surface voltage detected. Database ?
Turn the headlights and blower ON.

YES

Reserve (build later)

4.31
Battery Health Check
NO
2018 Ford F150 V6, 3.5L
Please select the vehicle's battery
loop information

Option 1:
Battery Type: xx
Battery Standard: xx
Read Voltage (V2) Option select
Battery Rating: xx
--
Option 2:
NO
Battery Type: xx
loop Battery Standard: xx
Battery Rating: xx
--
Not Listed

Is V2 < (V1 - 0.2) ?

NOT LISTED

YES
3.29
Electrical System Test Process (func_BatteryHealthCheck):
Battery Standard 3.29
3.29
11.2 Electrical System Test 4.31 measure CCA
Electrical System Test CCA
Electrical System Test Enter the battery CCA value (on battery Electrical System Test
Battery Type CA calulate SOH
JIS label), then press OK to perform the test.
Turn the headlights and blower OFF. Flooded OK Testing battery health check ...
calulate SOC
DIN OK
AGM OK Internal resistance
GEL EN
DIN measure battery voltage
Back SAE measure battery temperature

Continue Back
Continue

4.4
Electrical System Test CCA result to determine
Charge the battery and Battery Health Check Status
retest. Return of: function_BatteryHealthCheck()
Is Vbatt > 11.8V
NO

Is CCA Result == CHARGE RETEST

NO (=Good Battery or Good Recharge) YES
or REPLACE BATTERY ?

30s countdown

Battery Standard
4.5 YES
4.10
= JIS ?
Electrical System Test
The engine must be started within 30 seconds Electrical System Test

Turn the engine and all vehicle accessories OFF

Time out NO

30
3.27b
Done
Electrical System Test 3.27b
Electrical System Test
BATTERY RESULT: <text result>
<status text description>
BATTERY RESULT: <text result>
NO checking <status text description>

State of Health (SOH): xxxx %

DONE State of Health (SOH): xxxx %
Is dectect Start Signal within 30s State of Charge (SOC): xxxx %
Measured: xxxx CCA State of Charge (SOC): xxxx %
Resistance: xxxx mΩ Measured: xxxx BBB
JIS NUMBER: xxxx xxxx CCA Resistance: xxxx mΩ
Battery type: xx Rating: xxxx BBB
Battery voltage: xx.xx V Battery type: xxxx
3.27b
Battery temperature: xx.xx oC Battery voltage: xx.xx V
Electrical System Test
Battery temperature: xx.xx oC

BATTERY RESULT: <text result> REPAIR TIPS:

REPAIR TIPS:
<status text description> 4.6 <text>
<text>
Electrical System Test
Report Complete
Report Complete
STARTER SYSTEM RESULT: NO START
Not detect start engine.
To
State of Health (SOH): xxxx % Battery Service Report
Drop voltage: -- V Report
State of Charge (SOC): xxxx % NEXT Cranking voltage: -- V Complete
Measured: xxxx CCA Starting time: -- ms
YES
Resistance: xxxx mΩ Complete
JIS NUMBER: xxxx xxxx CCA Complete
Battery type: xx
Battery voltage: xx.xx V
Battery temperature: xx.xx oC To
Report Battery To
REPAIR TIPS: Report Complete Service Battery Service
<text>

Next To
REPORT Report Battery
Service

Save the Starter System result of the

Starter System Test

checking

4.11
Charging System Analysis
The engine of the vehicle must be running during the
testing process.
Does OBD2 cable
Process Is PID NO
connected to YES
OBD2 PID 01 0C RPM (01 0C) > 0 ?
DLC ?
YES

Note: Please following the alternator test procedure for

NO safety and more accurate test results.
Does PID (01 0C)
supported ? YES

NO

5.4 5.4
Charging System Analysis Charging System Analysis

Increase engine speed and maintain at Increase engine speed and maintain at
2000-3000 RPM, then press Continue. 2000-3000 RPM.

checking Is RPM > 2000 ?

Continue
xx RPM
2 command:
Get voltage (1.5s first)
YES (delay 3s)
2 command: Get ripple (1.5s next)
Get voltage (1.5s first) 5.5 5.5
Get ripple (1.5s next) Charging System Analysis Charging System Analysis

Testing charging system at engine RPM Testing charging system at engine RPM
with accessories OFF. with accessories OFF.

5.6 5.6
Charging System Analysis Charging System Analysis

Return engine to idle speed, then press Return engine to idle speed, then press
Continue. Continue.

checking Is RPM < 2000 ?

Continue XX RPM

2 command: YES (delay 3s)

2 command: Get voltage (1.5s first)
Get voltage (1.5s first) Get ripple (1.5s next) 5.7
5.7
Get ripple (1.5s next) Charging System Analysis Charging System Analysis

Testing charging system at idle with Testing charging system at idle with
accessories OFF. accessories OFF.

5.8 5.8
Charging System Analysis Charging System Analysis

Turn the headlights and blower ON, then Turn the headlights and blower ON, then
press Continue. press Continue.

Continue Continue

2 command: 2 command:
Get voltage (1.5s first) Get voltage (1.5s first)
Get ripple (1.5s next) Get ripple (1.5s next)
5.9 5.9
Charging System Analysis Charging System Analysis

Testing charging system at idle with Testing charging system at idle with
accessories ON. accessories ON.

5.10 5.10
Charging System Analysis Charging System Analysis
NO
Increase engine speed and maintain at Increase engine speed and maintain at
2000-3000 RPM, then press Continue. 2000-3000 RPM, then press Continue.

checking Is RPM > 2000 ?

Continue XX RPM

2 command:
Get voltage (1.5s first) 2 command: YES
Get ripple (1.5s next) Get voltage (1.5s first)
5.11 5.11
Charging System Analysis
Get ripple (1.5s next) Charging System Analysis

Testing charging system at engine RPM Testing charging system at engine RPM
with accessories ON. with accessories ON.

5.12
Charging System Analysis 3.27b
BATTERY RESULT: <text result>
Turn the engine and all vehicle <status text description>
accessories OFF, then press Continue.

State of Health (SOH): xxxx %

Continue State of Charge (SOC): xxxx %
Measured: xxxx CCA
Resistance: xxxx mΩ
JIS NUMBER: xxxx xxxx CCA
Battery type: xx
Battery voltage: xx.xx V
Save the result of the Battery temperature: xx.xx oC
Charging System Analysis
REPAIR TIPS:
<text>

Next

Determine final test result

4.7
STARTER SYSTEM RESULT: CRANKING NORMAL
Starter operation is normal.

Drop voltage: xx.xx V

Cranking voltage: xx.xx V
Starting time: xx.xx ms

Back Next

5.13
CHARGING SYSTEM RESULT: GOOD
The charging system is good.

LOADED: x.xxV
NO LOAD: x.xxV To
Battery Service
AC Ripple Voltage: x.xxmV Complete

REPAIR TIPS:
Charging voltage is within specification.
To
Report Complete Report Battery
Service

REPORT
 Battery Tester Module - SDS43
X0.05 Voltmeter July 30 2024

From
Battery Service

To
RETRY Jump to screen
Always check battery Connection in 2.6
BLE Connection
whole test process.

6.1
Voltmeter

Was the SDS connected to Communication Failure

Battery Tester Module via NO
Please double-check the BLE or Battery
BLE ?
Tester Module clamps connection.

Retry Exit

YES

EXIT

6.3
Voltmeter
Exit To
Xx.xx V
Battery Service
Exit

YES

auto check

Is the BLE still connecting ? NO

 Battery Tester Module - SDS43
X0.05 REPORT PAGE July 30 2024

From
From From
From Report of
Report of Report of
Report of Charging
Starter System Electrical
Battery Health System
Test System Test
Check Analysis

5.5
REPORT

Battery TestID: (xxx)- random number

Date: MM/DD/YYYY
Time: HH:MM
5.5 Store Info:
5.5
REPORT
Print does not need to REPORT ELECTRICAL SYSTEM TEST
Graph Battery TestID: (xxx)- random number
Date: MM/DD/YYYY Battery TestID: (xxx)- random number
Date: MM/DD/YYYY BATTERY RESULT: <text result>
Time: HH:MM <status text description>
Store Info: Time: HH:MM
Store Info:

STARTER SYSTEM RESULT: <text result>

CHARGING SYSTEM RESULT: <text result>
<status text description>
<status text description>
State of Health (SOH): xxxx %
Drop voltage: xx.xx V State of Charge (SOC): xxxx %
Cranking voltage: xx.xx V LOADED: x.xxV Measured: xxxx CCA
Starting time: xx.xx ms NO LOAD: x.xxV Resistance: xxxx mΩ
AC Ripple Voltage: x.xxmV JIS NUMBER: xxxx xxxx CCA
Battery type: xx
REPAIR TIPS: Battery voltage: xx.xx V
<text> Battery temperature: xx.xx oC

REPAIR TIPS:
<text>
Share Print Share Print
STARTER SYSTEM RESULT: <text result>
<status text description>
Drop voltage: xx.xx V
Cranking voltage: xx.xx V
Starting time: xx.xx ms

CHARGING SYSTEM RESULT: <text result>

<status text description>
LOADED: x.xxV
NO LOAD: x.xxV
AC Ripple Voltage: x.xxmV
Report

REPAIR TIPS:
<text>

Share Print

8.27 5.5
Sign in To Your Wi-Fi Network REPORT

No Wi-Fi network found. Please check and Battery TestID: (xxx)- random number
Date: MM/DD/YYYY
try again EXIT Time: HH:MM
Store Info:
BATTERY RESULT: <text result>
Exit <status text description>

8.27
Printer Setting

State of Health (SOH): xxxx % EXIT No printer found. Please check for printer
State of Charge (SOC): xxxx % and Bluetooth connection.
Measured: xxxx CCA
Resistance: xxxx mΩ
JIS NUMBER: xxxx xxxx CCA Exit
Back Battery type: xx
Battery voltage: xx.xx V
Battery temperature: xx.xx oC

NO REPAIR TIPS:
<text> Exit
NO
Share Print

5.5 Share
5.5 5.5
Sign in To Your Wi-Fi Network Sign in To Your Wi-Fi Network Sign in To Your Wi-Fi Network Rescan
Password Innova 01 One moment please...
5.5 5.5 5.5
Innova 02 Print
Printer Setting Printer Setting Printer Setting
xxxx
My Printer Searching for printer ... Available Printer
OK Has the SDS tool connected to
YES Is any Wi-Fi network found ? NO
Wi-Fi ? Bluetooth printer's name 1 Bluetooth printer's name new 1
Bluetooth printer's name 2 Bluetooth printer's name new 2
Is there a saved printer in SDS YES
YES Is any printer found ?
tool ?
Back
YES
Rescan

Exit Other Printer

5.5
REPORT
Sumitting Data...
NO

OK

OK Is pasword correct ? YES Dont show OK

this again

5.5 5.5 5.5

REPORT REPORT Printer Setting
Exit
Print completed. Printing...
Connecting to printer ...
NO

YES Has priting been completed ?

OK

8.7 EXIT
5.5
Sign in To Your Wi-Fi Network REPORT
NO
The report will be automatically saved on the server, YES

Try again and it can be viewed using RSPro

The tool was unable to connect to Wi-Fi, please verify 5.5
network signal strength, remain close to the router, and
REPORT
try again. EXIT Printing incomplete, please check and try
again Can the SDS tool connect to RETRY
Try Again
printer ?

Dont show this again OK NO

EXIT
8.29
Printer Setting
Back
Couldn’t pair with Printer.
exit

Exit Retry
 From
HomeScreen

5.5
PREVIOUS VEHICLE

2020 Ford F150 (1FTxxxxxxxx)

2014 Toyota Camry (xxxxxxxxx)

Diagnostics Test Battery Test

Battery Test

No Are there saved battery test?

Diagnostics Test

After complete the test, save a report

Yes

5.5
5.5
PREVIOUS VEHICLE
PREVIOUS VEHICLE

1. Vehicle Information
There are currently no saved battery test in the
Funciton Test: Result (Data/Time)
tool.
2. Function Test: Result (Data/Time) Electrical System Test

Diagnostics Test Battery Test

Diagnostics Test Battery Test

Batetry Health Check

3.27b
3.27b
REPORT
REPORT
Battery TestID: (xxx)- random number
Battery TestID: (xxx)- random number
Date: MM/DD/YYYY
Date: MM/DD/YYYY
Time: HH:MM
Time: HH:MM
Store Info:
Store Info:

BATTERY RESULT: <text result> BATTERY RESULT: <text result>

<status text description>
<status text description>

State of Health (SOH): xxxx %

State of Health (SOH): xxxx %
State of Charge (SOC): xxxx %
State of Charge (SOC): xxxx %
Measured: xxxx CCA
Measured: xxxx CCA
Resistance: xxxx mΩ
Resistance: xxxx mΩ
JIS NUMBER: xxxx xxxx CCA
JIS NUMBER: xxxx xxxx CCA
Battery type: xx
Battery type: xx
Battery voltage: xx.xx V
Battery voltage: xx.xx V
Battery temperature: xx.xx oC
Battery temperature: xx.xx oC
REPAIR TIPS:
REPAIR TIPS:
<text>
<text>

Submit Data

4.7
STARTER SYSTEM RESULT: CRANKING NORMAL
Starter operation is normal.

Drop voltage: xx.xx V

Cranking voltage: xx.xx V
Starting time: xx.xx ms

Back Next

5.13
CHARGING SYSTEM RESULT: GOOD
The charging system is good.

LOADED: x.xxV
NO LOAD: x.xxV
AC Ripple Voltage: x.xxmV

REPAIR TIPS:
Charging voltage is within specification.

Submit Data
 Battery Tester Module - SDS43
X0.05 Battery Test July 30 2024
-------------------------------English---------------------------------- From
Battery Test Battery Service
Battery Test Conditions:
• Parking Brake is ON
• Transmission in PARK or NEUTRAL
• Inspect the battery for damage or corrosion
• Check electrolyte level on maintenance-type battery
• Ignition in Key ON, Engine OFF position

--------------------------------Spain-----------------------------------

• Condiciones de prueba de la batería: 83.1

• El freno de mano está activado Battery Test
• Transmisión en PARK o NEUTRAL
• Inspeccione la batería en busca de daños o corrosión. Battery Test Conditions:
• Verifique el nivel de electrolito en la batería de tipo • Parking Brake is ON
mantenimiento • Transmission in PARK or NEUTRAL
• Inspect the battery for damage or corrosion • Check
• Encendido en posición de llave en ON, motor APAGADO electrolyte level on maintenance-type battery • Ignition in
Key ON, Engine OFF position
---------------------------------France---------------------------------
Back Continue
•Conditions de test de la batterie:
• Le frein de stationnement est activé
• Transmission en PARC ou NEUTRE
• Inspectez la batterie pour détecter tout dommage ou
corrosion
• Vérifier le niveau d′électrolyte sur la batterie de type Enter
entretien
• Contact en position clé ON, moteur OFF

83.2
Battery Test
Is RPM PID greater
Yes Turn the engine OFF.
than 0? Turn the key to the ON
position, do not start the
engine.

No

83.3
Battery Test

Turn ON head lights.

Continue

Enter
Count down from 20s. When Retest
timer gets to 1 capture voltage
83.4 for test result.
Battery Test

One moment please…

20

83.5 -------------------------------English----------------------------------
Battery Test Battery Test

Turn OFF head lights. Charge the battery before performing Battery Test
--------------------------------Spain-----------------------------------
Continue
Cargar la batería antes de realizar la prueba de la batería
---------------------------------France---------------------------------
Enter
Chargez la batterie avant d′effectuer le test de batterie
-------------------------------English---------------------------------- 83.6
Battery Test
Battery Test
Battery voltage is low, this may affect the accuracy of the test results.
Battery voltage
<= 11.8V Charge the battery before performing Exit
(Vbatt)?
Battery Test
--------------------------------Spain-----------------------------------
Exit
El voltaje de la batería es bajo, esto puede afectar la
precisión de los resultados de la prueba. 11.8V < Vbatt < 12.1V

---------------------------------France---------------------------------
83.12
La tension de la batterie est faible, cela peut affecter la Battery Test To
>= 12.1V
précision des résultats du test. Battery Service
Battery voltage is low, this may
affect the accuracy of the test
results.

Continue RETEST

Tool will auto detect 1 time start

-------------------------------English----------------------------------
83.7 engine for 30 seconds.
Battery Test
Start the engine -------------------------------English----------------------------------
The engine must be started within 30 seconds of Start the engine
Battery Test
beginning the test.
The engine must be started within 30
Unable to perform the test
--------------------------------Spain----------------------------------- seconds of beginning the test. --------------------------------Spain-----------------------------------
El motor debe arrancarse dentro de los 30 segundos Incapaz de realizar la prueba
posteriores al inicio de la prueba. ---------------------------------France---------------------------------
---------------------------------France--------------------------------- 83.8 Impossible d′effectuer le test
Battery Test
Le moteur doit être démarré dans les 30 secondes Does tool detect
suivant le début du test. Cranking Status No
after 30s timeout ?
Unable to perform the test

Exit Retest -------------------------------English----------------------------------

Battery Test

Battery Status: Pass

Yes
--------------------------------Spain-----------------------------------
83.9
Battery Test Estado de la batería: Aprobar
---------------------------------France---------------------------------
Battery Status: Pass
État de la batterie : Réussi
Is battery Good? Yes Exit

Exit

-------------------------------English----------------------------------
No Battery Test

Battery Status: Marginal

83.10 Charge and retest.
Battery Test --------------------------------Spain-----------------------------------
Battery Status: Marginal
Charge and retest. Estado de la batería: marginal
Is battery Warning? Yes Exit Cargue y vuelva a probar.
---------------------------------France---------------------------------

État de la batterie : marginal

Exit Chargez et retestez.

No

83.11 -------------------------------English----------------------------------
Battery Test Battery Test

Battery Status: Fail

Battery Status: Fail No Replace Battery.
Yes Replace Battery.
Is battery Bad? Exit --------------------------------Spain-----------------------------------

Estado de la batería: Falla

Reemplazar la batería.
---------------------------------France---------------------------------
Exit

État de la batterie : échec

Remplacer la batterie.
 Battery Tester Module - SDS43
X0.05 Battery Livedata (12 Volt) July 30 2024

From
Battery Service

2.13

Battery Live Data (12 Volt)

One moment please …

2.14

Battery Live Data (12 Volt)

Battery Live Data (12 Volt) is not supported

for this vehicle. Is this vehicle
No supported this
function ?
Exit

Yes
EXIT

To
Battery Service 2.15
Battery Live Data (12 Volt)
1/XX
Battery Voltage V
Battery Current A
EXIT
Battery Temperature °C / °F
Battery State of Charge %
Battery State of health (SOH) %
…..
Exit
 Battery Tester Module - SDS43
X0.05 Alternator Test July 30 2024

From
Alternator Test

26.1
Alternator Test

Alternator Test Conditions:

Parking brake is ON
Transmission is in PARK or
Continue Back
NEUTRAL
The engine is running
Turn ON the headlights

Note: Do not perform this test on

Smart Alternator, Hybrid and Electric
26.10
Continue Alternator Test
26.11
The engine of the vehicle must be Alternator Test
running during the testing process.
Is RPM (01 0C) PID Increase and keep the engine speed at
NO Continue
supported? Note: Please following the user 2000-3500 then press continue.
interface for safety and more accurate
test results.
Continue
Back Continue
26.15
Alternator Test
YES
The engine of the vehicle must be
Continue
running during the testing process.
Is RPM PID greater
Note: Please following the alternator No
than 0RPM?
test procedure for safety and more ADC read: get 1 sample/second (1s
accurate test results. 26.12 interval), get continuously for 20s. And
Alternator Test calculate the mean (average) => get this
Continue
value as the result to compare
(XX.XX Volts)
The FW must run 2 tasks at the same time:
- ADC read: get 1 samples/second (1s Keep the engine speed at 2000-3500 RPM
26.2
interval), get continuously for 20s. And until the countdown reaches zero.
Alternator Test
calculate the mean (average) => get this Because the RPM PID does not support, FW
(XX.XX Volts)
value as the result to compare 20 just check ADC, and countdown timer to
- RPM check: check PID 01 0C continuously reach zero, resetting timer is no needed.
(Engine RPM XXXX) >2000RPM, reset timer to 20s if RPM <
2000 After countdown
Increase and keep the engine speed at
2000-3500 RPM until the countdown
reaches zero.
20sec countdown when RPM is equal to or
greater than 2000rpm. Countdown reset if 26.13
20 RPM return to idle at anytime during test. Alternator Test Show screen after the countdown timer
reaches zero
Turn OFF the headlights, and return
After Countdown
engine to idle speed then press
continue.

Confirmed that the engine speed Continue

is below 1000RPM before
26.3
displaying the result.
Alternator Test
Continue
Turn OFF the headlights, and return
engine to idle speed.

26.14
The FW read ADC Voltage (1s interval)
NO Alternator Test
within 3 seconds to display.
One moment please…

(XX.XX Volts)
RPM value < 1000 ?

After 3s

26.4 The FW read ADC Voltage (1 Interval)

Alternator Test and RPM PID within 3 seconds to
display.
One moment please…

(XX.XX Volts)
(Engine RPM XXXX)

After 3s

26.5
Alternator Status: Voltage High

(Voltage PID XX.XXv)

Is voltage PID above The charging voltage is above the acceptable
Yes limit. This could cause damage to the battery or Exit
14.9v? other electrical components. Refer to the
appropriate service information or have the
charging system inspected by a certified repair
facility.

Exit
NO

26.8
Alternator Status: Good

Is voltage PID between

(Voltage PID XX.XXv) To
Yes Exit
13.3v to 14.9v? Battery Service
The charging voltage is within
specification.

Exit

No

26.9
Alternator Status: Voltage Low

(Voltage PID XX.XXv)

Is voltage PID below The charging voltage is under the acceptable
Yes limit. This could cause damage to the battery Exit
13.3v?
or other electrical components. Refer to the
appropriate service information or have the
charging system inspected by a certified
repair facility.

Exit
Battery Tester Module - SDS43
X0.05 Alternator Live Data July 30 2024

From
Battery Service

2.17

Alternator Live Data

One moment please …

2.18

Alternator Live Data

Alternator Live Data is not supported for
Is this supported? No this vehicle.

Exit

Yes

EXIT

2.19
Alternator Live Data
1/XX
Actual Alternator Current A
Alternator Voltage V To
EXIT
Alternator charge status YES/NO Battery Service
Alternator fault lamp Off/ On
Alternator Load %
…..
Exit
 Battery Tester Module - SDS43
X0.05 Battery Reset July 30 2024

From
Battery Service

2.14

Battery Reset Procedures

Does this vehicle There are no reset procedures available.

have any Battery
Reset Procedure? NO
Exit

YES

Exit

2.14

Battery Reset Procedures

This function should only be used when:

1. The battery replacement function has
not been used after the battery has been To
replaced. Battery Service
2. The battery has been disconnected from
the vehicle.

Exit

Continue

2.14

Battery Reset Procedures

General Information
Battery Disconnection Precautions
Battery Connection Precautions
Battery Connection Procedures Back

Exit

2.14
Battery Reset Procedures
General Information

1. Turn on the ignition but do not start the engine

2. Using the squares and circle button behind the
steering wheel, use squares to cycle to setting and
press circle
General Information 3. Select maintenance, press circle
4. Select desired maintenance item and reset Back
mileage intervals
5. Repeat for different items
6. Turn off ignition when done

Back

2.14

Battery Reset Procedures

Battery Disconnection Precautions
Battery Disconnection
1. Turn on the ignition but do not start the Back
Precautions
engine
2. Using the squares and circle button
behind the steering wheel, use squares to
cycle to setting and press circle Back
3. Select maintenance, press circle

2.14

Battery Reset Procedures

Battery Connection Precautions
Battery Connection
Precautions 1. Turn on the ignition but do not start the
engine Back
2. Using the squares and circle button
behind the steering wheel, use squares to
cycle to setting and press circle
3. Select maintenance, press circle

2.14

Battery Reset Procedures

Battery Connection Precautions
Battery Connection
1. Turn on the ignition but do not start the
Procedures
engine
2. Using the squares and circle button
behind the steering wheel, use squares to
cycle to setting and press circle
3. Select maintenance, press circle
 Battery Tester Module - SDS43
X0.05 Battery Initialization July 30 2024

Erase – Disable
From System Menu – Disable
Battery DTC/FF – Disable
Initialization Live Data – Disable
Main Menu – Disable
Up/Down Arrow – Disable
Enter – Disable
Power/Re-link – Disable

37.1

OBD Service OEM Item Name

<Description/Instruction Display
Here>

Exit Next

Next

37.2

OBD Service OEM Item Name Live data item

displayed if available

LD ID_1 xx
LD ID_2 xx

Back Next

Next

37.3

OBD Service OEM Item Name

Resetting. One moment please...

Successful Fail

37.4
37.5
OBD Service OEM Item Name
OBD Service OEM Item Name
Live data item
<Successful Result Text Display Here> <Failure Result Text Display Here>
displayed if available
LD ID_1 xx LD ID_1 xx
LD ID_2 xx LD ID_2 xx

Exit Exi

Exit
Exit

To
Battery Service
 Battery Tester Module - SDS43
X0.05 EV/HEV/PHEV Battery Health July 30 2024

From
Battery Service

2.20

To EV/HEV/PHEV Battery
Battery Service Health

One moment please …

2.21

EV/HEV/PHEV Battery Health

EV/HEV/PHEV Battery Health is not Is this vehicle
Exit supported for this vehicle. No supported this
function ?

Exit

Exit
Yes
Show Livedata 2.22

EV/HEV/PHEV Battery Health

X/X
Hybrid State of Charge XX.XX % No Does this vehicle support
Hybrid Pack Voltage XX.XX V Hybrid Battery Cells?
Sum of Cell Voltages XX.XX V
xx

Exit
Yes

2.23

EV/HEV/PHEV Battery Health

Exit
 Battery Tester Module - SDS43
X0.05 EV/HEV/PHEV Inspection July 30 2024

From
Battery Service

2.24

EV/HEV/PHEV
Inspection

One moment please …

2.25

EV/HEV/PHEV Inspection

EV/HEV/PHEV Inspection is not supported Is this vehicle

for this vehicle. No supported this
function ?

Exit

Yes

EXIT

2.26
EV/HEV/PHEV Inspection
HV Battery Charge Level xx %
HV Battery Temperature xx o F
To
EXIT Remaining Distance Available xx miles
Battery Service
HV Battery State of Health (SOH) xx %

Exit