SC.1000.

10” Table Saw - 3 Wire 110 V - 1 Phase

INSTRUCTION MANUAL

ATTENTION: READ THIS MANUAL BEFORE USING THE MACHINE.

1
Greetings,

Congratulations, you just purchased the SC.1000.I Maksiwa Table Saw, which
was developed with the Maksiwa’s highest standards of technology and quality.
Your SC.1000.I Maksiw Table Saw allows you to have the highest productivity in
woodworking. It should be noted that to use this machine with maximum efficiency,
you should read and understand the instructions in this manual.
Visit our website to know about our launches and other product lines and Technical
Assitance:
www.maksiwa.com/usa
[email protected]

2
! Attention!: The machine must be inspected immediately upon arrival. If the machine has been
damaged during transport, or if any parts are missing, a written record of the problems must be
submitted to the forwarding agent and a damage report compiled. Also be sure to notify your
supplier immediately.

For the safety of all personnel, it is necessary to study this manual thoroughly before assembly
and operation. This manual must be kept in good condition and should be considered as part
of the machine. Furthermore, the manual must be kept to hand and within the vicinity of the
machine so that it is accessible to operators when using, maintaining or repairing the machine.

Maksiwa International Inc.

4100 N Powerline Rd, Suite D3 Pompa-
no Beach, FL

Call us free: 844-319-6594

[email protected]
www.maksiwa.com/usa

3
Contents
1. General.....................................................................................................................................................................05
1.1 Symbol legend ................................................................................................................................................05
1.2 Information on the operating instructions ..................................................................................................05
1.3 Liability and warranty.....................................................................................................................................05
1.4 Copyright........................................................................................................................................................06
1.5 Spare parts.....................................................................................................................................................06
1.6 Disposal .........................................................................................................................................................06
2. Safety Regulations...............................................................................................................................................07
2.1 Workspace.....................................................................................................................................................07
2.2 Maintainance .................................................................................................................................................07
2.3 Machine Safety..............................................................................................................................................08
3.Specifications......................................................................................................................................................13
3.1 Technical Specifications ...................................................................................................................................13
3.2 Electrical Requirements .................................................................................................................................13
4. Installation...............................................................................................................................................................15
4.1 Unpacking and Checking Contents ...............................................................................................................15
4.2 Assembly ..........................................................................................................................................................17
5. Operating Procedures ........................................................................................................................................32
5.1Description ......................................................................................................................................................32
5.2 Starting and Stopping the Saw ......................................................................................................................32
5.3 Adjustments ......................................................................................................................................................33
5.3 Types of Cuts/Operations ...............................................................................................................................39
6. Maintenance ........................................................................................................................................................43
6.1 Safety Instructions ........................................................................................................................................43
6.2 Cleaning .........................................................................................................................................................43
6.3 Lubrication .....................................................................................................................................................43
6.4 Service ...........................................................................................................................................................43
6.5 Changing the Blade Saw .................................................................................................................................44
7. Troubleshooting .................................................................................................................................................45
8. Exploded View ......................................................................................................................................................47
9. Wiring Diagram .....................................................................................................................................................57
10. Terms of Warranty ...............................................................................................................................................58

4
 1 General

1 General

1.1 Symbol legend

Important technical safety instructions in this manual are marked with symbols.
These instructions for work safety must be followed.

In all these particular cases, special attention must be paid in order to avoid accidents, injury to persons or
material damage.

Warning! Risk of injury or death!

This symbol marks instructions that must be followed in order to avoid harm to one’s health, injuries,
permanent impairment or death!

Warning! Danger! Electric current!

This symbol warns of potentially dangerous situations relating to electrical current. Not observing the
safety instructions increases the risk of serious injury or death. All electrical repairs must be carried
out by a qualified electrician!

! Attention! Risk of material damage!

This symbol marks instructions which, if not observed, may lead to material damage, functional
failures
and/or machine breakdown!

1.2 Information on the operating instructions

This manual describes how to operate the machine properly and safely. Be sure to follow the safety tips and
instructions stated here as well as any local accident prevention regulations and general safety regulations.
Before beginning any work on the machine, ensure that the manual, in particular the chapter entitled “Safety”
and the respective safety guidelines, has been read in its entirety and fully understood. This manual is an
integral part of the machine and must therefore be kept in the direct vicinity of the machine and be accessible
at all times. If the machine is sold, rented, lent or otherwise transferred to another party, the manual must
accompany the machine.

1.3 Liability and warranty

The contents and instructions in this manual have been compiled in consideration of current regulations and
state-of-the-art technology as well as based on our know-how and experience acquired over many years. This

5
 1 General

manual must be read carefully before commencing any work on or with this machine. The manufacturer shall
not be liable for damage and/or faults resulting from the disregard of instructions in the manual. The text
and images do not necessarily represent the delivery contents. The images and graphics are not depicted
on a 1:1 scale. The actual delivery contents are dependent on custom-build specifications, add-on options
or recent technical modifications and may therefore deviate from the descriptions, instructions and images
contained in the manual. Should any questions arise, please contact the manufacturer. We reserve the right
to make technical modifications to the product in order to further improve user-friendliness and develop its
functionality.

1.4 Copyright

This manual should be handled confidentially. It is designated solely for those persons who work on or with the
machine. All descriptions, texts, drawings, photos and other depictions are protected by copyright and other
commercial laws. Illegal use of the materials is punishable by law.
This manual, in its entirety or parts thereof, may not be transferred to third parties or copied in any way or
form, and its contents may not be used or otherwise communicated without the express written consent of
the manufacturer.
Infringement of these rights may lead to a demand for compensation or other applicable claims. We reserve
all rights in exercising commercial protection laws.

1.5 Spare parts

Attention: Non genuine, counterfeit or faulty spare parts may result in damage, cause malfunction or
! complete breakdown of the machine.

If unauthorized spare parts are fitted into the machine, all warranty, service, compensation and liability claims
against the manufacturer and their contractors, dealers and representatives shall be rejected. Use only genuine
spare parts supplied by the manufacturer. Unless, specified by manufactor.

1.6 Disposal

Attention!: Used electrical materials, electronic components, lubricants and other auxiliary substances
must be treated as hazardous waste and may only be disposed of by specialised, licensed firms.

If the machine is to be disposed of, separate the components into the various materials groups in order to
allow them to be reused or selectively disposed of. The whole
structure is made of steel and can therefore be dismantled without problem. This material is also easy to
dispose of and does not pollute the environment or jeopardize public health. International environmental
regulations and local disposal laws must always be complied with.

6
 2 Safety Regulations

2 Safety Instructions

For your own safety, read all of the instructions and precautions before operating tool.

• Wear proper apparel. Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry which
may get caught in moving parts of machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with the Standard of your country. Everyday glasses have only impact
resistant lenses. They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools when tired, intoxicated or when taking medications
that cause drowsiness.

2.1 Workspace

• Keep work area clean. Cluttered work areas invite accidents.

• Do not use power tools in dangerous environments. Do not use power tools in damp or wet locations. Do
not expose power tools to rain.
• Work area should be properly lighted.
• Keep visitors at a safe distance from work area.
• Keep children out of workplace. Make workshop childproof. Use padlocks, master switches or remove
switch keys to prevent any unintentional use of power tools.
• Keep power cords from coming in contact with sharp objects, oil, grease and hot surfaces.

2.2 Maintainence

• Always unplug tool prior to inspection.

• Consult manual for specific maintaining and adjusting procedures.
• Keep tool lubricated and clean for safest operation.
• Remove adjusting tools. Form habit of checking to see that adjusting tools are removed before switching
machine on.
• Keep all parts in working order. Check to determine that the guard or other parts will operate properly and
perform their intended function.
• Check for damaged parts. Check for alignment of moving parts, binding, breakage, mounting and any
other condition that may affect a tool’s operation.
• A guard or other part that is damaged should be properly repaired or replaced. Do not perform makeshift
repairs. (Use parts list provided to order replacement parts.)

7
 2 Safety Regulations

• Maintain proper adjustment of rip fence and blade guard.

• Never adjust saw while running. Disconnect power to avoid accidental start-up.
• Have damaged or worn power cords replaced immediately.
• Keep blade sharp for efficient and safest operation.

2.3 Machine Safety

• Use right tool for job. Do not force tool or attachment to do a job for which it was not designed.
• Disconnect tool when changing blade.
• Avoid accidental start-up. Make sure that the tool is in the “off” position before plugging in, turning on safety
disconnect or activating breakers.
• Do not force tool. It will work most efficiently at the rate for which it was designed.
• Keep hands away from blade and moving parts and cutting surfaces.
• Never leave tool running unattended. Turn the power off and do not leave tool until it comes to a complete
stop.
• Do not overreach. Keep proper footing and balance.
• Never stand on tool. Serious injury could occur if tool is tipped or if blade is unintentionally contacted.
• Know your tool. Learn the tool’s operation, application and specific limitations.
• Handle workpiece correctly. Press firmly against table. Protect hands from possible injury.
• Turn machine off if it jams. Blade jams when it digs too deeply into workpiece. (Motor force keeps it stuck
in the work.)
• Feed work into the blade only as recommended in “Operation.”.

WARNING! FOR YOUR OWN SAFETY, DO NOT OPERATE YOUR SAW UNTIL IT IS COMPLETELY
ASSEMBLED AND INSTALLED ACCORDING TO INSTRUCTIONS.

STABILITY OF SAW
If there is any tendency for the saw to tip over or move during certain cutting operations, such as cutting extremely
heavy panels or long heavy boards, the saw should be bolted down. If you attach any kind of extensions over
24″wide to either end of the saw, make sure you either bolt the saw to the floor, as appropriate, or support the
outer end of the extension from the bench or floor, as appropriate.

LOCATION
The saw should be positioned so neither the operator nor a casual observer is forced to stand in line with the
saw blade.

KICKBACKS
A kickback occurs during a rip-type operation when a part or all of workpiece is thrown back violently toward
operator. Keep your face and body to one side of the saw blade, out of line with a possible kickback. Kickbacks

8
 2 Safety Regulations

and possible injury from them can usually be avoided by:

• Maintaining rip fence parallel to saw blade.
• Keeping saw blade sharp. Replace or sharpen anti-kick-back pawls when points become dull.
• Keeping saw blade guard, spreader, and anti-kickback pawls in place and operating properly. The spreader
must be in alignment with the saw blade and the pawls must stop a kickback once it has started. Check their
action before ripping.
• Not ripping work that is twisted or warped or does not have a straight edge to guide along the rip fence.
• Not releasing work until you have pushed it all the way past the saw blade.
• Using a push stick for ripping widths less than 6 inches.
• Not confining the cutoff piece when ripping or crosscutting.

PROTECTION: EYES, HANDS, FACE, BODY, EARS

• If any part of your saw is missing, malfunctioning, or has been damaged or broken (such as the motor switch,
electronic controls, other operating control, a safety device or power cord), cease operating immediately
until the particular part is properly repaired or replaced.
• Wear safety goggles that comply with the standard of your country and a face shield or dust mask if operation
is dusty. Wear ear plugs or muffs during extended periods of operation.
• Small loose pieces of wood or other objects that contact the rear of the revolving blade can be thrown back
at the operator at excessive speed. This can usually be avoided by keeping the guard and spreader in place
for all thru-sawing operations (sawing entirely thru work) and by removing all loose pieces from the table
with a long stick of wood immediately after they are cut off.
• Use extra caution when the guard assembly is removed for resawing, dadoing, or rabbeting, replace guard
as soon as that operation is completed.
• Never turn the saw ON before clearing the table of all tools, wood scraps, etc., except the workpiece and
related feed or support devices for the operation planned.
• Never place your face or body in line with the cutting tool.
• Never place your fingers or hands in path of saw blade or other cutting tool.
• For rip or rip-type cuts, the following end of a workpiece to which a push stick or push board is applied must
be square (perpendicular to the fence) in order that feed pressure applied to the workpiece by the push stick
or block does not cause the workpiece to come away from the fence, and possibly cause a kickback.
• During rip and rip-type cuts, workpiece must be held down on table and against fence with a push stick, push
block, or feather boards, as applicable (see following figures).
• Push stick: A safety device used to push the workpiece through a cutting operation. Used most often when
rip cutting thin workpieces.
• The push stick and push block examples shown below are useful for keeping hands and fingers away from
saw blade during ripping, rabbeting and dadoing. Apply downward pressure and push workpiece through
the cut and past the blades. Several other configurations may be suitable for safe operation. Feather boards
are used to keep the work in contact with the rip fence or table during the cutting operation. Use of feather

9
 2 Safety Regulations

boards can help to prevent kickbacks and binding. Feather boards should be used for all “non thru-sawing”
operations.
• Never reach in back of the cutting tool with either hand to hold down or support the workpiece, remove wood
scraps, or for any other reason. Avoid awkward operations and hand positions where a sudden slip could
cause fingers or hand to move into a saw blade or other cutting tool.
• Do not perform layout, assembly, or setup work on the table while the cutting tool is rotating.
• Do not perform any operation freehand—always use either rip fence or miter gauge to position and guide
the work.
• Never use the rip fence when cross-cutting or the miter gauge when ripping. Do not use rip fence as a length
stop. Never hold onto or touch free-end of workpiece or a free-piece that is cut off, while power is ON and/
or saw blade is rotating.
• Shut the saw OFF and disconnect power source when removing the table insert, changing the cutting tool,
removing or replacing the blade guard, or making adjustments.
• Provide adequate support to the rear and sides of the saw table for wide or long workpieces.
• Plastic and composition materials (like hardboard) may be cut on your saw. However, since these are usually
quite hard and slippery, the anti-kickback pawls may not stop a kickback. Therefore, be especially attentive
to following proper setup and cutting procedures for ripping. Do not stand, or permit anyone else to stand,
in line with a potential kickback.
• If you stall or jam the saw blade in the workpiece, turn saw OFF and remove the workpiece from the saw
blade. Check to see if the saw blade is parallel to the miter gauge grooves and if the spreader is in proper
alignment with the saw blade. If ripping at the time, check to see if the rip fence is parallel with the saw
blade. Readjust as required.
• Do not remove small pieces of cutoff material that may become trapped inside the blade guard while the
saw is running. This could endanger your hands or cause kick-back. Turn saw OFF and wait until blade stops.
• Use extra care when ripping wood with twisted grain or wood that is twisted or bowed—it may rock on table
and pinch saw blade.

10
 2 Safety Regulations

11
 2 Safety Regulations

KNOW YOUR CUTTING TOOLS

• Dull, gummy, improperly sharpened or set cutting tools can cause material to stick, jam, stall saw, or kickback
at operator. Minimize potential injury by proper care and machine maintenance.
WARNING: Never attempt to free a stalled saw blade without first turning saw OFF.
• Never use grinding wheels, abrasive cutoff wheels, friction wheels (metal slitting blades), wire wheels or
buffing wheels.

USE ONLY ACCESSORIES DESIGNED FOR SAW

• Crosscutting operations are worked more conveniently and with greater safety if an auxiliary wood facing
is attached to miter gauge using holes provided. However, facing must not interfere with proper functioning
of saw blade guard.
• Make sure the top of the arbor or cutting tool rotates toward you when standing in normal operating position.
Also make sure the cutting tool, blade flange and arbor nut are installed properly. Keep the cutting tool as
low as possible for the operation being performed. Keep all guards in place whenever possible.
• Do not use any blade or other cutting tool marked for operating speed less than 4000 RPM. Never use a
cutting tool larger in diameter than diameter for which saw was designed. For greatest safety and efficiency
when ripping, use maximum diameter blade for which saw is designed, since under these conditions
spreader is nearest the blade.
• Adjust table inserts flush with table top. Never operate saw unless proper insert is installed.
• Never feed material into the cutting tool from the rear of the saw. An accident and serious injury could result.

THINK SAFETY
Safety is a combination of operator common sense and alertness at all times when the saw is being used. Never
use another person as a substitute for a table extension, or as additional support for a workpiece that is longer
or wider than basic saw table, or to assist in feeding, supporting or pulling the workpiece.
Do not pull the workpiece through the saw blade—position your body at the infeed side of the guard; start and
complete the cut from that same side. This will require added table support for long or wide workpieces that
extend beyond the length or width of the saw table.
CAUTION: Follow safety instructions that appear on the front of your saw.

12
 3 Specifications

3 Specifications

3.1 Technical Specifications

Please choose proper power source, voltage and frequency that are shown in the label for your machine.

10” Contractor Table Saw

Motor 2.5 Hp 8 Amp or A 1800W
Table Size 20-1/8″X 27″ (512X685mm)
Extended Table Size 40″ X 27″ (1015X685mm)
Saw Blade 10″ X 5/8″ (254x15.875mm)
Maximum Cut Depth at 90° 3-1/8 ″ (80mm)
Maximum Cut Depth at 45° 2-3/16″ (55mm)
Blade angle 0~45°
Max. Ripping Capacity 30″ (762mm)
Blade Speed 60Hz 3450 RPM

3.1 Electrical Requirements

POWER SUPPLY AND MOTOR SPECIFICATIONS

WARNING: To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a
separate electrical circuit for your tools. To avoid shock or fire, if power cord is worn or cut, or damaged in any
way, have it replaced immediately.

GROUNDING INSTRUCTIONS
WARNING: This tool must be grounded while in use to protect the operator from electrical shock.
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment-
grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly
installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment-grounding conductor can result in risk of electric shock. The
conductor with green insulation (with or without yellow stripes) is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary, DO NOT connect the equipment-grounding conductor
to a live terminal.
CHECK with a qualified electrician or service person if you do not completely understand the grounding
instructions, or if you are not sure the tool is properly grounded.
Refer to nether picture:

13
 3 Specifications

WARNING: Improper connection of equipment grounding conductor can result in the risk of electrical shock.
Equipment should be grounded while in use to protect operator from electrical shock.
WARNING: This machine is for indoor use only. Do not expose to rain or use in damp locations.

GUIDELINES FOR EXTENSION CORDS

USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause
a drop in line voltage, resulting in loss of power and cause overheating.
Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension
cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.

ELECTRICAL CONNECTIONS
WARNING: Make sure unit is off and disconnected from power source before inspecting any wiring. The power
lines are inserted directly onto the switch. The green ground line must remain securely fastened to the frame
to properly protect against electrical shock.

14
 4 Installation

4 Installation

4.1 Unpacking and Checking Contents

Carefully unpack the table saw and all its parts, and compare against the illustration following.
WARNING:
• To avoid injury from unexpected starting, do not plug the power cord into a power source receptacle during
unpacking and assembly. This cord must remain unplugged whenever you are assembling or adjusting the
machine.
• If any part is missing or damaged, do not plug the machine until the missing or damaged part is replaced,
and assembly is complete.
TABLE OF LOOSE PARTS
Unpack carton; check you machine
to see parts listed below:

Item Parts Name Item Parts Name

1 TABLE SAW 15 CASTER (4)
2 EXTENSION TABLE (2) 16 FOOT (4)
3 BRACE 17 ANTI-KICKBACK PAWL ASSEMBLY
4 TABLE INSERT 18 BALDE GUARD ASSEMBLY
5 DUST CHUTE 19 PUSH STICK
6 RIP FENCE ASSEMBLY 20 LINK PLATE
7 MITER GAUGE ASSEMBLY 21 FRONT CASTER SUPPORT ASSEMBLY
8 FRONT RAIL (2) 22 REAR CASTER SUPPORT ASSEMBLY
9 REAR RAIL (2) 23 CORNER SUPPORT
10 HAND WHEEL WITH KNOB (2) 24 BASE PANEL “A” (2)
11 RIP FENCE STORAGE HOOKS (2) 25 BASE PANEL “B”
12 BLADE GUARD STORAGE HOOKS (2) 26 BASE PANEL “C”
13 PUSH STICK STORAGE HOOKS (2) 27 AAA BATTERY (2) The batteries are used for laser.
They will not be supplied, if your table saw is not
14 LINE CORDS HOOKS (2)
supplied lase

15
 4 Unpacking and Checking Contents

Hardware Bag #1 (For extension table assembly)

M10X25 Socket head bolt (6)
10mm Lock washer
10mm Flat washer
Hardware Bag #2 (For guide rail and brace assembly)
M8X30 Hex head bolt (16)
M8X16 Hex head bolt (4)
8mm Lock washer (20)
8mm Flat washer (20)
M8 Hex nut (16)
M8 Acorn hex nut (4)
Hardware Bag #3
M10X25 Socket head bolt (4) (For assembling stand to main machine)
10mm Lock washer (4)
10mm Flat washer (4)
M8X16 Socket pan head screw (8) (For assembling caster supports to corner support)
M6X12 Socket pan head screw (24) (For assembling corner support to base panel)
M6X20 Socket pan head screw (4) (For assembling fence storage hooks and line cord hooks)
6mm Flat washer (4)
M6 Hex nut (4)
M4X8 Pan head screw (8) (For assembling push stick storage and blade guard storage hooks)
4mm Flat washer (8)
Hardware Bag #4
10/13mm Open end wrench
2.5 mm Hex wrench
4mm Hex wrench
5mm Hex wrench
6mm Hex wrench
8mm Hex wrench
IMPORTANT: Table is coated with a protectant. To ensure proper fit and operation, remove coating. Coating
is easily removed with mild solvents, such as mineral spirits, and a soft cloth. Avoid getting solution on paint
or any of the rubber or plastic parts. Solvents may deteriorate these finishes. Use soap and water on paint,
plastic or rubber components. After cleaning, cover all exposed surfaces with a light coating of oil. Paste wax
is recommended for table top.
WARNING: Never use highly volatile solvents. Non flammable solvents are recommended to avoid

16
 4 Unpacking and Checking Contents

4.2 Assembly

CAUTION: Do not attempt assembly if parts are missing. Use this manual to order replacement parts. Be certain
all parts are clean and free of shipping preservative. Also, completely remove all parts of packing. Saw cabinet
should be directly on the floor.

SAW INSTALLATION
Positioning the saw on a level surface will improve stability and accuracy and prevent warpage and failure of
cast components and welds.
WARNING: Make certain that the saw is disconnected from the power source.

INSTALL HANDWHEELS
Refer to following figure
• Remove saw cabinet and place upside down on cardboard on floor.
• Place one of the handwheels onto the blade raise/lower shaft located on the front of the cabinet. Align the
groove in the back of the handwheel with the pin.
• Thread the washer and locking knob onto the threaded end of the shaft.
• Repeat the steps above to assemble the remaining handwheel and locking knob onto the blade tilt shaft
located on the side of the cabinet.

REMOVE PACKING MATERIAL

Refer to following figure
• Use the blade tilt handwheel to tilt the motor completely to45°.
• Remove the packing material from behind the motor.
• Return motor to the 0° position.

17
 4 Unpacking and Checking Contents

ASSEMBLE MOBILE BASE PANELS

Refer to following figure
Tools Required: 4mm Hex wrench
Hardware Required: Twenty-four M6 x 12 socket pan head bolts (Hardware bag #3).
• Attach the four panels to four corner supports using M6 x 12 socket pan head screws.
NOTE: Place the panel edges INSIDE the corner support surfaces.
NOTE: Front panel and rear panel are both stamped ‘A’. Front panel has warning label.
• Turn all panels upside down to perform base assembly.

ASSEMBLE CASTER SETS

Refer to following figure
Tools Required: 6mm Hex wrench, 13mm Open End Wrenches
• Remove casters (4), link plate and caster supports (2) from carton.
• Loosen and remove the bolt and hex nut from the bracket.

18
 4 Unpacking and Checking Contents

• Rotate foot pedal bar so that kick plate cam is inside bracket.
• The kick plate cam must be underneath the caster to function properly.
• Place caster onto the bracket and secure in position with bolt and hex nut.
• Repeat above steps for the second caster set.

ATTACH CASTER SETS TO BASE

Refer to following figure
Tools Required: 5mm Hex wrench, 6mm Hex wrench and 13mm Open end wrench
Hardware Required: Eight M8 x 16 socket pan head screws (Hardware bag #3).
• Attach one caster set to the two front corner supports using four M8 x 16 socket pan head screws.
• Attach the remaining caster set to the two rear corner supports.
• Remove the socket head bolt and hex nut form the foot pedal, insert the link plate to the slot of foot pedal

19
 4 Unpacking and Checking Contents

and fix it by replacing the socket bolt and hex nut.

• Remove the socket head bolt and hex nut form the link block of rear caster set, insert the link plate to the
slot of link block and fix it by replacing the socket bolt and hex nut.

ATTACH CORD WRAP HOOKS

Refer to following figure
Tools Required: 4mm Hex wrench, 10mm Open end wrench
Hardware Required: Two M6 x 20 socket pan head bolts, two M6 flat washers and two M6 hex nuts (Hardware
bag #3).
• Insert a bolt into a cord wrap hook and place against the holes on the left side of the saw cabinet.
• Secure hook in position using flat washer and hex nut.
• Repeat for other hook.

Line cord hook

20
 4 Unpacking and Checking Contents

ATTACH BASE TO CABINET

Refer to following figure.
Tools Required: 8mm Hex wrench
Hardware Required: Four M10 x 25 socket head bolts, four 10mm lock washers and four 10mm flat washers
(Hardware bag #3).
• Place dust chute over the cabinet as shown. Make sure the holes in the corners are aligned with the slots in
the dust chute.
• Place the base assembly over the dust chute and secure the base assembly to the cabinet using the flat
washers, lock washers and bolts.
• Secure all fasteners in the base assembly fully tight.

ATTACH RIP FENCE STORAGE BRACKETS

Refer to following figure.
Tools Required: 4mm Hex wrench and 10mm Open end wrench
Hardware Required: Two M6 x 20 socket pan head screws, two 6mm flat washers and two 6mm hex nuts
(Hardware bag #3).
• Install the rip fence storage brackets to the right side panel of the base using two bolts, flat washers and
hex nuts.

21
 4 Unpacking and Checking Contents

BLADE GUARD AND PUSH STICK STORAGE BRACKETS

Refer to following figure.
Tools Required: Phillips screwdriver
Hardware Required: Eight M4 x 8 pan head screws, eight 4mm flat washers (Hardware bag #3).
• Install the push stick storage brackets to the left side panel of the base using four screws and flat washers.
• Install the blade guard storage brackets to the left side panel of the base using four screws and flat washers.
NOTE: Attach the slotted bracket to the front side of the saw.
• Press the four rubber feet to the base legs.
• With the aid of an assistant turn the saw upright.
WARNING: To avoid injury, Do Not attempt to turn saw upright by yourself.

ATTACH EXTENSION TABLES

Refer to following figure.
Tools Required: 8mm Hex Wrench and Straight Edge
Hardware Required: Six M10 x 25 socket head bolts, six 10mm lock washers and six 10mm flat washers
(Hardware bag #1).
• Assemble extension table to the table using socket head bolts, lock washers and flat washers.
• Wipe surface clean.
• Hand tightens only. Do not tighten completely until tables are level. Use a straightedge to level tables.
• Repeat above procedure for the other extension table.
• Use a straight edge to check level and flatness between main and extension tables.
• After tables are adjusted level and flat, secure the extension tables by tightening the bolts completely.

22
 4 Unpacking and Checking Contents

INSTALL BLADE
Refer to following figure.
Tools Required: 24mm Open end Wrench
• Loosen knob on right side of cabinet.
• Remove blade and wrench. Replace knob.
• Raise blade assembly all the way up.
• Depress arbor lock and use wrench to loosen flange nut. Remove flange and nut from arbor.
• Place blade on arbor. Make sure arrow on blade and teeth point towards front of saw.
• Replace flange and nut on arbor and securely snug blade in position.

CHECK TABLE ALIGNMENT

Refer to following figure.
• Saws are shipped from the factory with the table adjusted so the miter gauge slots are parallel to the saw
blade. However, in order to obtain the best results from the saw, it is suggested this adjustment be checked
before operating.
• A simple method of checking alignment is as follows: Bolt or clamp a dowel rod or similar object to miter

23
 4 Unpacking and Checking Contents

gauge (a combination square can be substituted). Pick out a tooth on front of blade and set the dowel to it
so it is just touching. Move same tooth to back of blade.

• Gauge this tooth with the dowel rod. If the tooth is in the same position, relative to the miter gauge slot, the
table is parallel with the blade. In short, the miter gauge slots must be parallel with the blade. This means
that when measuring distance between blade and miter gauge slot at the front and rear of the blade, the
distances will be equal.
NOTE: Be sure to measure the distance or make the test on the same tooth of the saw blade in both front
and rear positions.
• If an adjustment is necessary, proceed as follows: Loosen and remove the six socket pan head screws and
the rear panel. Loosen the four socket head bolts on the trunnion and shift trunnions until a position is found
where the saw blade is parallel to the miter gauge slots.
NOTE: Saw blade should also be centered within its table insert opening.
• Tighten the four socket head bolts and lock washers very securely. This procedure will set the table and
blade in parallel position and prevent the trunnion from shifting.
NOTE: If you perform this adjustment, leave the back panel off to perform rear rail assembly as described
in the next section.

24
 4 Unpacking and Checking Contents

RAIL ASSEMBLY
Tools Required: 13mm Open end Wrench
Hardware Required: Sixteen M8 x 30 hex head bolts, four M8 x 16 hex head bolts, twenty 8mm lock washers,
twenty 8mm flat washers, sixteen M8 hex nuts and four M8 acorn nuts. (Hardware bag #2).
• Insert four M8 x 30 hex head bolts into the T-slot of the right front guide rail.
• Attach right front rail to the table and right table extension using flat washers, lock washers and hex nuts.
NOTE: Hand tighten all hardware during rail assembly. Do not completely tighten hardware until all rails are
mounted.
• Attach left front rail in the same manner.
NOTE: You may have to shift right rail as far right as it will go to attach left rail.
• Position rails so that rails are butted together and the joint between rails is aligned with right side of the
blade. You may need a mallet to lightly tap rails together. Make sure rails are completely butted together at
the joint.
• Use a straight edge as shown to check level and flatness between right and left rail. Use a combination
square as shown to make certain that both front rails are parallel to the table surface.
• After front rails are adjusted level and flat, tighten the screws completely.
• Secure all hardware completely.

25
 4 Unpacking and Checking Contents

• Loosen and remove six socket pan head screws and the back panel. This will allow easier attachment of
the rear rails.
• Install the rear rails in the same manner as the front rails and align the rail joint to the blade.
• Replace back panel of the cabinet.

• Insert M8 x 16 hex bolts through holes in bracket at each end of brace. Attach brace to the far right end of
the rails by sliding hex bolts into the rail T-slots. Secure bolts in position with flat washers, lock washers and
nuts.

ATTACH SWITCH ASSEMBLY

Refer to following figure.
Tools Required: 10mm Open end Wrench

26
 4 Unpacking and Checking Contents

Hardware Required: Two M6 x 16 hex head bolts, two 6mm flat washers, two 6mm lock washers and two M6 hex
nuts. (Attached on the switch assembly support bracket.)
• Insert bolt heads into T-slot on bottom of left front rail.
• Slide switch assembly 6″to 8″from left end of rail as shown in figure.
• Fully tighten flat washers, lock washers and hex nuts to secure switch assembly in place.

POSITION AND ADJUST RIVING KNIFE

Refer to following figure.
• Riving knife is installed on the saw. Raise the blade completely to access the riving knife.
• Loosen the locking knob and raise the riving knife to its highest position. Riving knife has three holes for
three positions. The highest position is for all thru cuts. The middle position is for rabbets and other non-thru
cuts, (with guard and pawls removed). The lowest position is for dado cuts.
• Make sure locking pin is aligned with riving knife hole and secure in position by tightening locking knob.
• Riving knife must be in line with blade. Make sure riving knife sits flat against mounting bracket and lock
plate.

27
 4 Unpacking and Checking Contents

RIVING KNIFE TO BLADE ADJUSTMENT

• Riving knife to blade clearance: the gap between the riving knife and the saw blade should be an even
distance across the entire radius.
• The riving knife should also be in line with the saw blade. If adjustment is necessary:
1. Locate the riving knife bracket.
2. Loosen the two socket head screws slightly enough to move the bracket, bringing the riving knife in line with
the saw blade. Make sure the gap between the blade and knife is even and from 1⁄4 to 5⁄16″in distance.
3. Once the riving knife is aligned with the blade, tighten the socket head cap screws.

INSTALL TABLE INSERT

Refer to following figure.
• Make sure that the riving knife is raised to its highest position.
• Place table insert into throat of table.
• Insert is held in position by magnet in table.
• To adjust insert level with table, adjust leveling screws up or down.

ATTACH BLADE GUARD WITH LASER AND ANTI-KICKBACKPAWLS

Refer to following figure.
• Remove the thread forming screw and the battery cover. Insert the two AAA batteries and replace the battery
cover and thread forming screw.
The laser is an optional accessory. If your machine has not this part, skip this step.

• Place the slot of blade guard body over the riving knife. Slot of bushing is placed in the notch indicated in
following figure.
• The bushings have a beveled edge and must be located in the center of the notch to lock properly.

28
 4 Unpacking and Checking Contents

• Position guard completely down on riving knife and press latch to lock in position.
• Blade guard body should be parallel to the table. If not, adjust the 2mm set screws as necessary.
• Place anti-kickback pawl set onto riving knife at notches indicated. The spring pin is placed in the front notch
and bolt is placed in the rear notch.
• Press pawl set completely down and press latch to secure in position.
NOTE: The teeth of anti-kickback pawls should touch table surface. Use set screws to adjust if needed.

29
 4 Unpacking and Checking Contents

CHECK AND ADJUST THE LASER

The laser is an optional accessory. If your machine has not this part, skip this step.
• Turn on the switch, check if the laser line is in the middle of the blade and rail jointer. If not, some adjustments
are needed.(The rail jointer should have been aligned with blade)
• To adjust the laser line:
• Loosen the two set screw.
• Move and rotate the laser generator to adjust the laser line, make it is in the middle of the blade and rail
jointer.
• Retighten the two set screw.

INSTALL MITER GAUGE

Refer to following figure.
• The miter gauge comes preassembled. Unpack the miter gauge and clean thoroughly. Insert into storage
slots on right side of cabinet.

INSTALL PUSH STICK

Refer to following figure.

30
 4 Unpacking and Checking Contents

• Insert the push stick into brackets on left side of base.

•

INSTALL RIP FENCE

Refer to following figure.
• Position rip fence assembly at end of saw. Be certain locking lever is in UP unlocked position.
• Place rip fence assembly onto rails, positioning clamp over rear rail and then placing rip fence onto front
guide rail.
• Rip fence should now ride freely on rip fence rails. Once rip fence is completely installed, it should be parallel
with the miter gauge and perpendicular to the table. If not, refer to “Rip Fence Adjustment” in the Operation
section of this manual.

31
 5 Operating Procedures

5 Operating Procedures

5.1 Description

The 10″ contractor saw offers precise cutting performance for all woods up to 3-1⁄8″ thick. The saw is designed
for the professional user and is ruggedly constructed for continuous service. The 10″Saw is recommended for
use with a 10″ blade.
The saw features an extra large cast iron table. Saw body has on board storage for push stick, miter gauge, rip
fence and saw blades. Saw is equipped with a riving knife and a clear acrylic blade guard with anti-kickback
feature. Cabinet is constructed of heavy gauge welded steel, totally enclosed and is ported for a 4″vacuum hose.
Rip Fence Assembly features a heavy-duty precision rip fence that is designed for simple and one-hand
maneuverability. Front rail is calibrated in inches and millimeters with a magnified window for close tolerances.

Warning! Danger – Disconnect power before attempting any of the following procedures. Be certain
switch is in OFF position and safety disconnect (or breaker) is in OFF or open position. Saw blade must
not be moving. Saw blade will rotate freely after motor is turned off. Allow blade to come to a complete
stop before attempting any of the following procedures.
Warning! The operation of any power tool can result in foreign objects being thrown into the eyes, which
can result in severe eye damage. Always wear safety goggles complying with the standard of your country
before commencing power tool operation.

5.2 Starting and Stopping the Saw

Refer to following figure.
WARNING: Never operate saw without blade guards in place. Be sure blade is not in contact with workpiece
when motor is started. Start motor and allow saw to come to full speed.
WARNING: Make sure the electrical characteristics of motor nameplate and power source are the same.

• The ON/OFF switch is located under the front rail of the table saw at the left side.
• To turn saw on, stand to either side of the blade—never inline with it. Turn on the switch. Always allow saw
blade to come up to full speed before cutting.
• Do not turn motor switch ON and OFF rapidly. This action overheats the motor and may cause saw blade to
loosen.
• Never leave saw while the power is on.
• To turn the table saw off, press the large red OFF paddle or turn off the switch. Never leave saw until cutting
tool has come to a complete stop.

WARNING: Never operate saw without blade guards in place. Be sure blade is not in contact with workpiece
when motor is started. Start motor and allow saw to come to full speed.

32
 5 Operating Procedures

5.3 Adjustment

BLADE HEIGHT ADJUSTMENT

Refer to following figure.
• Blade height is controlled by handwheel on the front of the saw.
• To adjust height, loosen locking hand knob. Rotate knob counterclockwise approximately three turns. Turn
handwheel to desired blade height.
CAUTION: For safety, blade should be raised only 1/8″above the surface of the material to be cut. However, if
hollow ground blades are used, raise blade to its maximum height to allow for greater blade clearance.
• Lock blade height into position. Lock handwheel by tightening locking knob clockwise. Tighten only until
snug.
IMPORTANT: Do not over tighten. Only a small amount of pressure is necessary to lock handwheel securely.

BLADE TILT ADJUSTMENT

Refer to following figure.
• Blade height is controlled by handwheel on the front of the saw.
• To adjust height, loosen locking hand knob. Rotate knob counterclockwise approximately three turns. Turn
handwheel to desired blade height.
CAUTION: For safety, blade should be raised only 1/8″above the surface of the material to be cut. However, if
hollow ground blades are used, raise blade to its maximum height to allow for greater blade clearance.
• Lock blade height into position. Lock handwheel by tightening locking knob clockwise. Tighten only until
snug.
IMPORTANT: Do not over tighten. Only a small amount of pressure is necessary to lock handwheel securely.

33
 5 Operating Procedures

90° STOP ADJUSTMENT

Refer to following figure.
• Raise saw blade above table as far as possible. Set blade at 90° to table by turning the tilting handwheel.
Place a square on table and check to see if blade is perpendicular to the table. When checking put square
flush against saw blade. Do not put square on teeth of saw blade.
• If the blade will not tilt to 90°, turn (counterclockwise) the set screw at the left front of the table insert until
the blade can be positioned to 90°.
• Once the blade has been tilted to 90° (confirm this using your square), tighten the bevel handwheel lock
knob, located on the side of the cabinet. This will keep the blade from tilting further.
• Turn the set screw (clockwise) until it comes in contact with the positive stop.
• Check tilt indicator pointer. If necessary, adjust pointer so it points to 0° mark on scale. To adjust pointer,
remove handwheel and loosen screw on pointer. Be sure to tight-en screw securely after adjustment is
completed.

45° STOP ADJUSTMENT

Refer to following figure.
• Tilt the saw blade to 45°. Using a combination square, check to see if blade is 45° to the table.
• If the blade will not tilt to 45°, turn (counterclockwise) the set screw located at the right of the table insert,
until the blade can be positioned to 45°.
• With the blade at 45°, tighten the bevel handwheel lock knob to keep the blade from further tilting.
• Turn the set screw clockwise until it comes in contact with the positive stop.

TABLE INSERT ADJUSTMENT

Refer to following figure.
• The table insert must always be level with the saw table.
• Place a straight edge across the front and rear of the table insert. Check that the insert is perfectly level with

34
 5 Operating Procedures

the saw table.

• To level the table insert, turn one or more adjusting setscrews as needed and recheck.
• The table insert is equipped with two finger holes for easy removal.

MITER GAUGE ADJUSTMENT

Refer to following figure.
• Miter gauge supplied with saw is equipped with individually adjustable index stops at 0° and 45°, right
and left, and can be manually adjusted up to 60° right and left. Adjustment to index stops can be made by
loosening locking nut and tightening or loosening three adjusting screws. Be sure to tighten locking nut after
adjustment is made.
• Face of miter gauge has two holes for purpose of attaching auxiliary facing.
• Miter gauge is accurately constructed for precision work. Miter gauge is guided through T-slot with a roller
guide mounted at front of guide bar. Roller guide adds to miter gauge’s stability and prevents the guide bar
from leaving T-slot.
• To operate miter gauge, simply loosen locking knob and move miter gauge to desired angle. The miter
gauge will stop at 0° and 45°, both right and left. To position miter gauge past these points, simply pull out
gauge stop. Position miter gauge at desired angle and tighten locking knob.
• Be positive the edge of workpiece next to face of miter gauge is straight and tight against miter gauge so
that the workpiece does not rock or rotate. Always use both hands when operating the miter gauge.
• The miter gauge is used for cross-cutting, compound miter cutting, miter cutting, rabbeting, bevel cutting
and dadoing.

35
 5 Operating Procedures

RIP FENCE ADJUSTMENT

• The saw’s rip fence is precision manufactured, incorporating fine adjustments for accurate cuts. The saw is
built to allow the operator to accurately adjust the rip fence without problems in a matter of seconds.

LEVELING THE FENCE TO THE TABLE

• Lift the lock handle to unlock the fence.
• Observe the space between the fence bottom and the table. The space should be equal along the entire
length of the fence.
• If the space is not equal, the rails need to be adjusted so that rails are at the same vertical position with
respect to the table. See Rail Assembly.

SETTING CLAMPING PRESSURE

Refer to following figure.
Rip fence has been adjusted at the factory to lock securely when the lock handle is pushed down. To adjust:
• Unlock fence and remove it from the rails.
• Adjust the hex nut until the fence is held securely when the lock handle is pushed down,

SETTING FENCE PERPENDICULAR AND PARALLEL

Refer to following figure.

PERPENDICULAR ADJUSTMENT
• Position fence anywhere on table and lock it down.
• Place a square on the table next to the fence and check to see that the fence is at 90° to the table.
• If an adjustment is necessary, unlock the fence and turn either of the two adjusting screws.
NOTE: This is for micro-adjustment only. If fence cannot be adjusted square, recheck rail adjustment.
• Lock fence in position and recheck. Continue this procedure until fence is square to the table.

36
 5 Operating Procedures

PARALLEL ADJUSTMENT
• Position fence so that fence edge is aligned with slot edge.
• Slot and fence edge should be parallel.
• If an adjustment is necessary, unlock the fence and turn either of the two adjusting screws.
• Lock fence in position and recheck. Continue this procedure until fence is square to the table.

CURSOR ADJUSTMENT
Refer to following figure.
• Raise the saw blade above the table.
• Position the fence several inches to the right of the saw blade.
• Lock the fence down and measure the exact distance between the saw blade and the inside of the fence.
• Loosen the two screws on the lens and slide it left or right until the cursor (red line) equals the measurement
obtained in the previous step.
• Retighten the screws and make a test cut. Measure the cut piece to verify that the cursor is set correctly.
NOTE: This adjustment should be checked whenever a new blade is installed.

37
 5 Operating Procedures

RIP FENCE OPERATION

Refer to following figure.
• Unlock the fence by lifting the locking lever. Using the scale for placement, position the rip fence. Lock the
rip fence into position by placing the locking lever in the down position.
• The rip fence is used for the following operations: ripping, bevel ripping, ploughing, resawing, rabbeting and
dadoing

INSTALLING AND REMOVING THE RIVING KNIFE

Refer to following figure.
Install
• Line up the riving knife in the proper direction to the mounting bracket.
• Push the riving knife all the way down into the mounting bracket. Make sure the lock pin is locked in the hole
of the riving knife. (The lock hole is on the button side of the riving knife).
• If the riving knife is not locked properly, hold the locking knob and pull the lock pin out; then re-insert the pin
securely in the hole of the riving knife. While raising or lowering the knife, pin will snap in the hole of the knife
when located atone of the three positions.
• Tighten the locking knob.
Remove
• Loosen the locking knob.
• Hold the knob and pull the locking pin out.
• Remove the riving knife out of the mounting bracket.
NOTE: Make sure blade is at the highest position before adding or removing the riving knife.

WARNING: For your own safety, always observe the following safety precautions.
• Never make any cut freehand (without using miter gauge or rip fence). Blade can bind in the cut and cause
a kick-back.
• Always lock miter gauge or rip fence securely when in use.
• Remove rip fence from the table when miter gauge is in use.
• Remove miter gauge from table when rip fence is in use.

38
 5 Operating Procedures

• Make sure blade guard is installed for all “through sawing” operations. Through sawing operations are
those operations in which the saw blade cuts completely through thethickness of the wood. Replace guard
immediately after completion of resawing, rabbeting and dadoing. Frequently check action of anti-kickback
pawls by passing the workpiece alongside the spreader while saw is off. Pull the workpiece toward you. If
the pawls do not dig into the workpiece and hold it, the pawls must be sharpened. (See Maintenance section)
• Have blade extend approximately 1/8″above top of workpiece. Additional blade exposure increases hazard
potential.
• Do not stand directly in front of blade in case of a kick-back. Stand to either side of the blade.
• Keep your hands clear of the blade and out of the path of the blade.
• If the blade stalls or stops while cutting, turn switch OFF and safety disconnect OFF before attempting to
free the blade.
• Do not reach over or behind the blade to pull the work-piece through the cut, to support long or heavy work-
pieces, to remove small cut-off pieces of material or for any other reason.
• Do not pick up small pieces of cut-off material from the table. Remove them by pushing them off table with
a long stick. Otherwise they could be thrown back at you by the rear of the blade.
• Do not remove small pieces of cut-off material that may become trapped inside blade guard while saw is
on. This could endanger your hands or cause a kickback. Turn saw off. After blade has stopped turning, lift
guard and remove the piece.
• Always lower blade below the table level when machine is not in use.

5.4 Types of Cuts/Operations

CROSSCUTTING
WARNING: Use caution when starting the cut to prevent binding of the guard against the workpiece.
This cut is performed with the miter gauge set at “0”, and is used for cutting across the workpiece grain at 90°
(blade square with both the edge and flat side of wood).

MITER CUTTING
WARNING: Miter angles greater than 45° may force the blade guard assembly into the saw blade causing damage
to the blade guard assembly and personal injury. Before starting the motor, test the operation by feeding the
workpiece into the blade guard assembly. If the blade guard assembly contacts the blade, place the workpiece
under the blade guard assembly, not touching the blade, before starting the motor.
WARNING: Certain workpiece shapes, such as molding may not lift the blade guard assembly properly. With the
power off, feed the workpiece slowly into the blade guard area and until the workpiece touches the blade. If the
blade guard assembly contacts the blade, place the workpiece under the blade guard assembly, not touching
the blade, before starting the motor.
This cut is performed with the miter gauge, and is used for cutting at an angle other than 90° square with the
edge of the workpiece.

BEVEL CROSSCUTTING
WARNING: When possible, use the right miter gauge slot when bevel crosscutting so that the blade tilts away

39
 5 Operating Procedures

from the miter gauge and your hands.

WARNING: Use caution when starting the cut to prevent binding of the guard against the workpiece.
This cut is performed with the miter gauge, and is the same as crosscutting, except that the workpiece is also
cut at an angle other than 90° square to the flat side of the wood (blade is at an angle).

COMPOUND MITER CUTTING

This cut is performed with the miter gauge, and is a combination of miter cutting and bevel crosscutting. The cut
is made at angle other than 90° to both the edge and flat side of wood.

RIPPING
WARNING: When bevel ripping and whenever possible, place the fence on the side of the blade so that the
blade is tilted away from the fence and hands. Keep hands clear of the blade and use a push stick to feed the
workpiece if there is less than 6″between the fence and the blade.
This cut is performed with the rip fence, and is used to cut the workpiece lengthwise with the grain. Position the
fence to the desired width of rip and lock in place. When ripping long boards or large panels, always use a work
support.

BEVEL RIPPING
WARNING: Before connecting the table saw to the power source or operating the saw, always inspect the blade
guard assembly and riving knife for proper alignment and clearance with saw blade. Check alignment after each
change of bevel angle.
WARNING: When possible, place the fence on the right side of the blade so that the blade is tilted away from the
fence and hands. Keep your hands clear of the blade and use a push stick to feed the workpiece if there is less
than 6″between the fence and the blade.
This cut is performed with the rip fence, and is the same as ripping, except that the blade is set at an angle other
than 90°.

RESAWING
This cut is performed with the rip fence, and is used to rip a workpiece through its thickness rather than across
its flat width. Do not attempt to resaw bowed or warped material.
NOTE: It may be necessary to remove blade guard and use work supports as well as push blocks when performing
this operation.
WARNING: Install blade guard immediately upon completion of resawing operation.

PLOUGHING
This cut is performed with the rip fence, and is used to make a groove lengthwise with the grain of the workpiece.
Use proper hold downs and feed devices.

RABBETING
This cut is performed with either the miter gauge or rip fence. Rabbeting is used to cut out a section of the corner

40
 5 Operating Procedures

of a workpiece, across an end or along an edge. To make a rabbet requires cuts which do not go all the way
through the material. Therefore, blade guard must be removed. Install blade guard immediately upon completion
of rabbeting operation. Rabbet cuts can also be made using dado head.

DADOING
This cut is performed with either the miter gauge or rip fence. Dadoing is done with a set of blades (dado set)
rather than standard saw blades. The dado set is used to groove wood similar to ploughing and rabbeting.
However, the dado set allows operator to remove more material in one pass. The operator, with a dado set, can
vary width of cut up to 13⁄16″.
Instructions for operating dado set are contained in owner’s manual furnished with dado set. Dadoing requires
cuts which do not go all the way through material. Therefore, blade guard must be removed. Dado sets have
different characteristics than saw blades. As a result, saw must be fitted with special parts that are furnished
with saw.
When using a dado set, the following parts must be substituted dado table insert (not included).
IMPORTANT: Always use correct insert. When using the dado set, use caution. Use feather boards and push
sticks as applicable.
WARNING: Always immediately replace the standard blade, blade guard and blade insert when you are finished
dadoing.

FREEHAND
Freehand is a very dangerous operation of making a cut with-out using the miter gauge or rip fence. Freehand
cuts must never be performed on a Table Saw.

CUTTING OVERSIZED WORKPIECES

When cutting long workpieces or large panels, always support workpiece that is not on table. Use adjustable
roller stand or make simple support by clamping a piece of plywood to sawhorse. Add facings to miter gauge
or rip fence as needed.
IMPORTANT: Do not allow facings to interfere with operation of blade guard.

DUST COLLECTING
• Saw is fitted with a 4″male exhaust port.
• Before starting saw, see that all adjustments are properly made and guards in place. With power disconnected,
turn pulley by hand to make sure everything is correct before connecting power and starting saw.
•
BLADE SELECTION
Blade selection is based on type of material being cut and how it will be cut. There are three general types of saw
blades: rip saw blades cut with grain of wood, cut-off saw blades cut across grain, and combination saw blades
cut with grain, across grain and any angle to grain.
Blades vary in many aspects. When selecting a blade, the following blade characteristics should match up with
operation to be performed and type of material to be cut: type of steel; quality of steel; tooth style; tooth set;

41
 5 Operating Procedures

carbide tipped; grind; number of teeth and size.

IMPORTANT: Your saw is only as accurate and efficient as blade or cutting tool used.
First, be certain to use the appropriate type of cutting tool for the operation to be performed. Second, it is
strongly recommended that high-quality blades and cutting tools be used. Be certain blades and cutting tools
are kept sharp and in good working order. Check blades periodically and replace or sharpen if necessary.

42
 6 Maintenance

6 Maintenance

6.1 Safety instructions

Warning! Risk of injury: improper maintenance can cause serious injury or damage. For this reason, this
work may only be carried out by authorised, trained personnel who are familiar with how to operate the
machine and in strict observance of all safety instructions.

• Before beginning any maintenance work on the machine, switch it off and secure it against accidentally
being switched on again.
• Ensure that there is sufficient space to work around the machine.
• Keep the work area orderly and clean. Components and tools that are not put in their correct place or put
away may be the cause of accidents!

Warning! Danger – Do not attempt under any circumstances, to service, repair, dismantle, or disassemble
any mechanical or electrical components without physically disconnecting all power sources.

6.2 Cleaning

• Clean off any preservative on bright (machined ) parts with appropriate solvent (mineral spirits). Avoid
getting cleaning fluid on any rubber parts as they tend to deteriorate rubber.
• Use soap and soft water on rubber and plastic parts.
• After cleaning, lubricate unpainted surfaces with a light application of medium consistency machine oil.
This lubrication should be repeated at least once every six months.
NOTE: Instead of oil, a good quality paste wax can be applied to rip fence and table surface. Paste wax will
enhance movement of workpieces. In addition to providing lubrication, paste wax will help prevent rusting.
• Keep your machine and your workshop clean. Do not allow sawdust to accumulate on saw or inside cabinet.
Frequently vacuum or blow out any sawdust that may accumulate within cabinet.
• Be certain motor and internal mechanisms are clean and are frequently vacuumed or blown free of any dirt.

6.3 Lubrication
All bearings on the arbor are shielded ball bearings. These bearings are permanently lubricated at the factory.
• As needed, clean the grease off the rack and worm gears of height and tilt mechanism. Lubricate rack and
gears with a medium viscosity machine oil.
• Be sure to lubricate trunnion ways and all bushings.
• Occasionally oil all other bearing points, including blade guard assembly, miter gauge and rip fence.

6.4 Service
• Replace belts and worn parts as needed. If power cords are worn, cut, or damaged in any way, have them

43
 6 Maintenance

replaced immediately.
• Make sure teeth of anti-kickback pawls are always sharp.
• Sharpen dull teeth using a few light strokes of a smooth cut flat file.

6.5 Changing the Saw Blade

Refer to following figure.
WARNING: Turn the power switch “OFF” and unplug the power cord from its power source when changing the
saw blade.
WARNING: When replacing blades, check the thickness stamped onto the riving knife. You must select a blade
with a kerf width larger than the thickness of the riving knife. Thinner blades may cause the workpiece to bind
during cutting.
WARNING: USE ONLY 10″diameter blades with 5⁄8″arbor holes, rated at or higher than 3800 R.P.M.
• Remove blade guard assembly and pawl assembly.
• Remove the table insert.
• Unlock the raise/lower handwheel lock and raise saw blade to maximum height.
• Depress locking pin and slowly rotate blade toward you until pin engages into arbor. Hold arbor in locked
position.
• Place supplied open-end wrench on the arbor nut. Turn wrench counterclockwise to loosen nut. Remove
arbor nut, blade flange and saw blade.
• Place new blade on arbor. Make sure saw blade teeth point down at the front side of saw table. Place flange
and nut on arbor and securely snug blade in position.
• Replace table insert.
• Replace blade guard assembly and pawl assembly.

44
 7 Troubleshooting

7 Troubleshooting

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Saw stops or will not start 1.Overload tripped 1.Allow motor to cool and reset by pushing
reset switch
2.Saw unplugged from wall or motor 2.Check all plug connections
3.Fuse blown or circuit breaker tripped 3.Replace fuse or reset circuit breaker
4.Cord damaged 4.Replace cord
5.Defective capacitor 5.Replace capacitor
Excessive vibration 1.Stand on uneven floor 1.Reposition on flat, level surface
2.Damaged saw blade 2.Replace saw blade
3.Bad drive V-belts 3.Replace drive V-belts
4.Bent pulley 4.Replace pulley
5.Improper motor mounting 5.Check and adjust motor
6.Loose hardware 6.Tighten hardware
7.Loose set screw in pulley 7.Tighten set screw
Cannot make square cut when Miter gauge not adjusted properly Adjust miter gauge
crosscutting
Blade stalls (however, motor 1.Drive belts not tight 1.Adjust drive belt tension
turns) 2.Drive belts worn 2.Replace drive belts
Blade does not come up to 1.Extension cord too light or too long 1.Replace with adequate size cord
speed 2.Low shop voltage 2.Contact your local electric company
3.Motor not wired for correct voltage 3.Refer to motor junction box
Cut binds, burns or stalls when 1.Dull blade with improper tooth set 1.Sharpen or replace blade
ripping 2.Blade is binding at one end of 2.Adjust table and rip fence parallel to blade
cut(heeling) 3.Make sure concave or hollow side is
3.Warped board facing down; feed slowly
4.Rip fence not parallel to blade 4.Adjust rip fence
5.Riving knife out of alignment 5.Adjust riving knife to fall in line with blade
6.Excessive feed rate 6.Reduce feed rate
Cut not true at 45 or 90° Positive stops not properly adjusted Adjust blade tilt
positions
Tilt and elevating handwheel 1.Sawdust on rack and worm gears 1.Clean and relubricate
difficult to turn 2.Bushings and bearing surfaces dirty 2.Clean thoroughly and lubricate
Rip fence binds on guide tube 1.Guide rails or extension wing not 1.Reassemble guide rails
properly installed
2.Guide of rip fence not adjusted 2.Adjust guides
properly

45
 7 Troubleshooting

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Frequent opening of fuses or 1.Motor overloaded 1.Feed work slower into blade
circuit breakers 2.Fuses or circuit breakers do not 2.Install proper size fuses or circuit breakers
have sufficient capacity
Material kicked back from 1.Rip fence out of alignment 1.Align rip fence with miter slot
blade 2.Riving knife not aligned with blade 2.Align riving knife with blade
3.Feeding stock without rip fence 3.Always use rip fence or miter gauge
4.Riving knife not in place 4.Install riving knife
5.Dull blade 5.Replace blade
6.Letting go of material before it is 6.Push material all the way past blade
past blade before releasing work
7.Anti-kickback fingers dull 7.Replace or sharpen anti-kickback fingers
Saw makes unsatisfactory cut 1.Dull blade 1.Sharpen or replace blade
2.Blade mounted backwards 2.Turn blade around
3.Gum or pitch on blade 3.Remove blade and clean
4.Incorrect blade for cut 4.Change blade to correct type
5.Gum or pitch on table 5.Clean table

46
 8 Exploded View

8 Exploded View

47
 8 Exploded View

Part A
PARTS NUMBER ITEM PARTS NAME QTY

SPMAK-SC1-A01 1 FENCE REAR SUPPORT 1

SPMAK-SC1-A02 2 10X50MM SPRING PIN 1

SPMAK-SC1-A03 3 3.5-1.3X13MM THREAD FORMING SCREW 2

SPMAK-SC1-A04 4 FENCE 1

SPMAK-SC1-A05 4.1 GUIDE PLATE 2

SPMAK-SC1-A06 4.2 6-1.0X12MM SOCKET PAN HEAD SCREW 8

SPMAK-SC1-A07 4.3 6-1.0MM HEX NUT 8

SPMAK-SC1-A08 5 8-1.25X20MM SOCKET HEAD BOLT 2

SPMAK-SC1-A09 6 8MM LOCK WASHER 2

SPMAK-SC1-A10 7 8MM FLAT WASHER 2

SPMAK-SC1-A11 8 4-0.7X10MM PAN HEAD SCREW 2

SPMAK-SC1-A12 9 4MM FLAT WASHER 2

SPMAK-SC1-A13 10 POINTER 2

SPMAK-SC1-A14 11 FENCE FRONT SUPPORT 1

SPMAK-SC1-A15 12 RETAINING RING 2

SPMAK-SC1-A16 13 LOCKING HANDLE 1

SPMAK-SC1-A17 14 8X50MM SPRING PIN 1

SPMAK-SC1-A18 15 BUSHING 1

SPMAK-SC1-A19 16 SHAFT 1

SPMAK-SC1-A20 17 5X50MM SPRING PIN 1

SPMAK-SC1-A21 18 ADJUSTING SCREW 2

SPMAK-SC1-A22 19 ADJUSTING BLOCK 2

SPMAK-SC1-A23 20 RETAINING RING 2

SPMAK-SC1-A24 21 SLIDING PAD 2

SPMAK-SC1-A25 21.1 4-0.7X6MM PAN HEAD SCREW 2

SPMAK-SC1-A26 22 NYLON SCREW 2

SPMAK-SC1-A27 23 FRONT LOCKING PLATE 1

SPMAK-SC1-A28 24 8X50MM SPRING PIN 1

SPMAK-SC1-A29 25 ROD 1

SPMAK-SC1-A30 26 5-0.8X8MM PAN HEAD SCREW 1

SPMAK-SC1-A31 27 REAR LOCKING PLATE 1

SPMAK-SC1-A32 28 6MM FLAT WASHER 1

SPMAK-SC1-A33 29 SPRING 1

SPMAK-SC1-A34 30 6MM FLAT WASHER 1

SPMAK-SC1-A35 31 CLAMP 1

SPMAK-SC1-A36 32 6MM FLAT WASHER 1

SPMAK-SC1-A37 33 LOCK NUT 1

SPMAK-SC1-A38 34 LOCK NUT 1

SPMAK-SC1-A39 35 FLAT WASHER 2

SPMAK-SC1-A40 36 RETAINING RING 2

SPMAK-SC1-A41 37 KICKBACK PAWL 2

48
 8 Exploded View

Part A

PARTS NUMBER ITEM PARTS NAME QTY PARTS NUMBER ITEM PARTS NAME QTY

SPMAK-SC1-A42 38 BUSHING 2 SPMAK-SC1-A81 77 4MM FLAT WASHER 1

SPMAK-SC1-A43 39 SPRING 1 SPMAK-SC1-A82 78 4-0.7X20MM PAN HEAD SCREW 1

SPMAK-SC1-A44 40 3-0.5X10 PAN HEAD SCREW 1 SPMAK-SC1-A83 79 LASER SWITCH 1

SPMAK-SC1-A84 80 LASER AND BOX ASSEMBLY 1

SPMAK-SC1-A45 41 SUPPORT BRACKET 1
SPMAK-SC1-A85 81 BATTERY BOX ASSEMBLY 1
SPMAK-SC1-A46 42 4X30MM SPRING PIN 1
SPMAK-SC1-A86 82 BATTERY COVER 1
SPMAK-SC1-A47 43 PIVOT PIN 1
SPMAK-SC1-A87 83 THREAD FORMING SCREW 2
SPMAK-SC1-A48 44 4X12MM SPRING PIN 1
SPMAK-SC1-A88 84 AAA BATTERY 2
SPMAK-SC1-A49 45 LATCH 1

SPMAK-SC1-A50 46 6-1.0X60MM HEX HEAD BOLT 1

SPMAK-SC1-A51 47 6MM FLAT WASHER 1

SPMAK-SC1-A52 48 LEFT BLADE GUARD 1

SPMAK-SC1-A53 49 LOCK NUT 1

SPMAK-SC1-A54 50 6MM FLAT WASHER 1

SPMAK-SC1-A55 51 5-0.8X20MM SET SCREW 2

SPMAK-SC1-A56 52 4-0.7X10MM FLAT HEAD SCREW 2

SPMAK-SC1-A57 53 SUPPORT PLATE 1

SPMAK-SC1-A58 54 GUARD CASE 1

SPMAK-SC1-A59 55 BUSHING 2

SPMAK-SC1-A60 56 PLATE 1

SPMAK-SC1-A61 57 PIVOT PIN 1

SPMAK-SC1-A62 58 4X12MM SPRING PIN 1

SPMAK-SC1-A63 59 LATCH 1

SPMAK-SC1-A64 60 RIGHT BLADE GUARD 1

SPMAK-SC1-A65 61 6MM FLAT WASHER 1

SPMAK-SC1-A66 62 LOCK NUT 1

SPMAK-SC1-A67 63 KNOB 1

SPMAK-SC1-A68 64 8MM FLAT WASHER 1

SPMAK-SC1-A69 65 MITER GAUGE 1

SPMAK-SC1-A70 66 4-0.7MM HEX NUT 3

SPMAK-SC1-A71 67 4-0.7X16MM PAN HEAD SCREW 3

SPMAK-SC1-A72 68 4-0.7X10MM PAN HEAD SCREW 1

SPMAK-SC1-A73 69 POINTER 1

SPMAK-SC1-A74 70 BLOCK 1

SPMAK-SC1-A75 71 PIN 1

SPMAK-SC1-A76 72 4-0.7X12MM PAN HEAD SCREW 2

SPMAK-SC1-A77 73 SCREW 1

SPMAK-SC1-A78 74 BAR 1

SPMAK-SC1-A79 75 WASHER 1

SPMAK-SC1-A80 76 6-1.0X8MM FLAT HEAD SCREW 1

49
 8 Exploded View

50
 8 Exploded View

Part B
PARTS NUMBER ITEM PARTS NAME QTY PARTS NUMBER ITEM PARTS NAME QTY

SPMAK-SC1-B01 1 LEFT REAR RAIL CAP 1 SPMAK-SC1-B36 35 6-1.0MM HEX NUT 2

SPMAK-SC1-B02 2 LEFT REAR RAIL 1 SPMAK-SC1-B37 36 SWITCH MOUNTING PLATE 1

SPMAK-SC1-B03 3 REAR RAIL CONNECTOR 1 SPMAK-SC1-B38 37 3.5-1.3X9.5MM THREAD FORMING SCREW 3

SPMAK-SC1-B04 4 RIGHT REAR RAIL 1 SPMAK-SC1-B39 38 STRAIN RELIEF 3

SPMAK-SC1-B05 5 RIGHT REAR RAIL CAP 1 SPMAK-SC1-B40 39 POWER CORD 1

SPMAK-SC1-B06 6 8-1.25X30MM HEX HEAD BOLT 8 SPMAK-SC1-B41 40 4MM SERRATED WASHER 2

SPMAK-SC1-B07 7 8MM FLAT WASHER 20 SPMAK-SC1-B42 41 4MM FLAT WASHER 2

SPMAK-SC1-B08 8 8MM LOCK WASHER 20

SPMAK-SC1-B43 42 4MM LOCK WASHER 2
SPMAK-SC1-B09 9 8-1.25MM HEX NUT 16
SPMAK-SC1-B44 43 4-0.7X8MM PAN HEAD SCREW 2
SPMAK-SC1-B10 10 8-1.25X30MM HEX HEAD BOLT 8
SPMAK-SC1-B45 44 SWITCH BOX 1
SPMAK-SC1-B11 11 8-1.25X16MM SOCKET HEAD BOLT 4
SPMAK-SC1-B46 45 CIRCUIT BREAKER 1
SPMAK-SC1-B12 12 TABLE INSERT 1
SPMAK-SC1-B47 46 SWITCH 1
SPMAK-SC1-B13 13 TABLE EXTENSION 2
SPMAK-SC1-B48 47 PADDLE 1
SPMAK-SC1-B14 14 10-1.5X25MM SOCKET HEAD BOLT 6

SPMAK-SC1-B15 15 10MM LOCK WASHER 6 SPMAK-SC1-B49 48 8MM FLAT WASHER 4

SPMAK-SC1-B16 16 10MM FLAT WASHER 6 SPMAK-SC1-B50 49 8MM LOCK WASHER 4

SPMAK-SC1-B17 17 5-0.8X16MM FLAT HEAD SCREW 4 SPMAK-SC1-B51 50 8-1.25X20MM SOCKET HEAD BOLT 4

SPMAK-SC1-B18 18 8-1.25X16MM SET SCREW 2 SPMAK-SC1-B52 51 6-1.0X20MM SOCKET PAN HEAD SCREW 2

SPMAK-SC1-B19 19 MAGNET 1
SPMAK-SC1-B53 52 LINE CORD HOOK 2

SPMAK-SC1-B20 19.1 4-0.7X8MM SOCKET HEAD BOLT 1

SPMAK-SC1-B54 53 6MM FLAT WASHER 2
SPMAK-SC1-B21 20 TABLE 1
SPMAK-SC1-B55 54 6-1.0MM HEX NUT 2
SPMAK-SC1-B22 21 BRACE 1
SPMAK-SC1-B56 55 FRONT CORNER COVER 2
SPMAK-SC1-B23 22 LOCK NUT 4
SPMAK-SC1-B57 56 6-1.0X12MM SOCKET PAN HEAD SCREW 18
SPMAK-SC1-B24 23 3.5-1.3X13MM THREAD FORMING SCREW 6
SPMAK-SC1-B58 57 BOX BASE 1
SPMAK-SC1-B25 24 LEFT FRONT RAIL CAP 1
SPMAK-SC1-B59 58 REAR CORNER COVER 2
SPMAK-SC1-B26 25 LEFT FRONT RAIL 1

SPMAK-SC1-B27 26 LEFT SCALE 1 SPMAK-SC1-B60 59 REAR PANEL 1

SPMAK-SC1-B28 27 FRONT PARTITION 1 SPMAK-SC1-B61 60 6-1.0X12MM SOCKET PAN HEAD SCREW 6

SPMAK-SC1-B29 28 CONNECTING PIN 3 SPMAK-SC1-B62 61 8-1.25X35MM HEX HEAD BOLT 1

SPMAK-SC1-B30 29 RIGHT FRONT RAIL 1 SPMAK-SC1-B63 62 8MM LOCK WASHER 1

SPMAK-SC1-B31 30 RIGHT SCALE 1 SPMAK-SC1-B64 63 SUPPORT BLOCK 1

SPMAK-SC1-B32 31 RIGHT FRONT RAIL CAP 1 SPMAK-SC1-B65 64 WRENCH 1

SPMAK-SC1-B33 32 6-1.0X16MM HEX HEAD BOLT 2 SPMAK-SC1-B66 65 KNOB 1

SPMAK-SC1-B34 33 6MM FLAT WASHER 2 SPMAK-SC1-B67 66 DUST CHUTE 1

SPMAK-SC1-B35 34 6MM LOCK WASHER 2

51
 8 Exploded View

52
 8 Exploded View

Part C
PARTS NUMBER ITEM PARTS NAME QTY

SPMAK-SC1-C01 1 LOCK NUT 1

SPMAK-SC1-C02 2 16MM FLAT WASHER 1

SPMAK-SC1-C03 3 MOTOR 1

SPMAK-SC1-C04 4 5X5X30MM KEY 1

SPMAK-SC1-C05 5 6-1.0X8MM SET SCREW 1

SPMAK-SC1-C06 6 MOTOR PULLEY 1

SPMAK-SC1-C07 7 6-1.0X10MM SOCKET HEAD BOLT 4

SPMAK-SC1-C08 8 6MM FLAT WASHER 4

SPMAK-SC1-C09 9 8-1.25X16MM HEX HEAD BOLT 1

SPMAK-SC1-C10 10 8MM LOCK WASHER 1

SPMAK-SC1-C11 11 8MM FLAT WASHER 1

SPMAK-SC1-C12 12 MOTOR SUPPORT BRACKET 1

SPMAK-SC1-C13 13 BELT 1

SPMAK-SC1-C14 14 LOCK NUT 1

SPMAK-SC1-C15 15 SPINDLE PULLEY 1

SPMAK-SC1-C16 16 SPACER 1

SPMAK-SC1-C17 17 6202ZZ BALL BEARING 1

SPMAK-SC1-C18 18 BLADE AND MOTOR SUPPORT CASE 1

SPMAK-SC1-C19 19 5-0.8X12MM PAN HEAD SCREW 2

SPMAK-SC1-C20 20 5MM FLAT WASHER 2

SPMAK-SC1-C21 21 BLADE LOCKING ASSEMBLY 1

SPMAK-SC1-C22 22 SPRING 1

SPMAK-SC1-C23 23 SPACER 1

SPMAK-SC1-C24 24 10-1.5X20MM SET SCREW 1

SPMAK-SC1-C25 25 MAIN TRUNNION 1

SPMAK-SC1-C26 26 10-1.5X40MM SOCKET HEAD BOLT 1

SPMAK-SC1-C27 27 10-1.5MM HEX NUT 1

SPMAK-SC1-C28 28 TRUNNION 2

SPMAK-SC1-C29 29 10MM FLAT WASHER 4

SPMAK-SC1-C30 30 10MM LOCK WASHER 4

SPMAK-SC1-C31 31 10-1.5X35 SOCKET HEAD BOLT 4

SPMAK-SC1-C32 32 6-1.0X20MM SOCKET PAN HEAD SCREW 2

SPMAK-SC1-C33 33 6MM LOCK WASHER 2

SPMAK-SC1-C34 34 6MM FLAT WASHER 2

SPMAK-SC1-C35 35 RIVING KNIFE SUPPORT ASSEMBLY 1

SPMAK-SC1-C36 36 RIVING KNIFE 1

SPMAK-SC1-C37 37 CLAMP 1

SPMAK-SC1-C38 38 6MM FLAT WASHER 1

SPMAK-SC1-C39 39 LOCK KNOB 1

SPMAK-SC1-C40 40 MOUNTING PLATE 1

SPMAK-SC1-C41 41 RIVET 1

53
 8 Exploded View

Part C

PARTS NUMBER ITEM PARTS NAME QTY PARTS NUMBER ITEM PARTS NAME QTY

SPMAK-SC1-C42 42 CONNECTING PLATE 1 SPMAK-SC1-C81 81 5-0.8X12MM PAN HEAD SCREW 2

SPMAK-SC1-C43 43 SCREW 1 SPMAK-SC1-C82 82 5MM FLAT WASHER 2

SPMAK-SC1-C44 44 SPRING 1 SPMAK-SC1-C83 83 5-0.8X8MM SOCKET HEAD BOLT 1

SPMAK-SC1-C45 45 5-0.8X6MM SET SCREW 3

SPMAK-SC1-C46 46 RETAINING RING 1

SPMAK-SC1-C47 47 BUSHING 1

SPMAK-SC1-C48 48 6203ZZ BALL BEARING 1

SPMAK-SC1-C49 49 KEY 2

SPMAK-SC1-C50 50 ARBOR 1

SPMAK-SC1-C51 51 BLADE 1

SPMAK-SC1-C52 52 FLANGE 1

SPMAK-SC1-C53 53 ARBOR NUT 1

SPMAK-SC1-C54 54 LOWER BLADE GUARD 1

SPMAK-SC1-C55 55 6MM FLAT WASHER 3

SPMAK-SC1-C56 56 6-1.0X10MM SOCKET HEAD BOLT 3

SPMAK-SC1-C57 57 SHAFT 1

SPMAK-SC1-C58 58 LOCK WASHER 1

SPMAK-SC1-C59 59 BEVEL NUT 1

SPMAK-SC1-C60 60 BEVEL SCREW 1

SPMAK-SC1-C61 61 3X20MM SPRING PIN 1

SPMAK-SC1-C62 62 BEARING FIXING PLATE 1

SPMAK-SC1-C63 63 BEARING 1

SPMAK-SC1-C64 64 RETAINING RING 1

SPMAK-SC1-C65 65 BEVEL LOCKING PLATE 1

SPMAK-SC1-C66 66 HANDWHEEL 2

SPMAK-SC1-C67 67 8MM FLAT WASHER 2

SPMAK-SC1-C68 68 LOCK NUT 2

SPMAK-SC1-C69 69 POINTER SUPPORT 1

SPMAK-SC1-C70 70 6MM FLAT WASHER 2

SPMAK-SC1-C71 71 6-1.0X10MM SOCKET HEAD BOLT 2

SPMAK-SC1-C72 72 ANGLE POINTER 1

SPMAK-SC1-C73 73 4MM FLAT WASHER 1

SPMAK-SC1-C74 74 4-0.7X8 PAN HEAD SCREW 1

SPMAK-SC1-C75 75 RETAINING RING 2

SPMAK-SC1-C76 76 16MM FLAT WASHER 2

SPMAK-SC1-C77 77 ELEVATION SHAFT 1

SPMAK-SC1-C78 78 3X20MM SPRING PIN 1

SPMAK-SC1-C79 79 BUSHING 1

SPMAK-SC1-C80 80 SPRING 1

54
 8 Exploded View

55
 8 Exploded View

Part D
PARTS NUMBER ITEM PARTS NAME QTY

SPMAK-SC1-D01 1 4-0.7X8MM PAN HEAD SCREW 8

SPMAK-SC1-D02 2 4MM FLAT WASHER 8

SPMAK-SC1-D03 3 PUSH STICK BRACKET 2

SPMAK-SC1-D04 4 REAR BLADE GUARD BRACKET 1

SPMAK-SC1-D05 5 FRONT BLADE GUARD BRACKET 1

SPMAK-SC1-D06 6 10MM FLAT WASHER 4

SPMAK-SC1-D07 7 10MM LOCK WASHER 4

SPMAK-SC1-D08 8 10-1.5X25MM SOCKET HEAD BOLT 4

SPMAK-SC1-D09 9 LEFT BASE PANEL 1

SPMAK-SC1-D10 10 LEG 4

SPMAK-SC1-D11 11 FRONT/REAR BASE PANEL 2

SPMAK-SC1-D12 12 RIGHT BASE PANEL 1

SPMAK-SC1-D13 13 6-1.0MM HEX NUT 2

SPMAK-SC1-D14 14 6MM FLAT WASHER 2

SPMAK-SC1-D15 15 RIP FENCE BRACKET 2

SPMAK-SC1-D16 16 6-1.0X20MM SOCKET PAN HEAD SCREW 2

SPMAK-SC1-D17 17 6-1.0X12MM SOCKET PAN HEAD SCREW 24

SPMAK-SC1-D18 18 FOOT 4

SPMAK-SC1-D19 19 8-1.25X16MM SOCKET PAN HEAD SCREW 8

SPMAK-SC1-D20 20 FRONT CASTER SUPPORT ASSEMBLY 1

SPMAK-SC1-D21 21 SCREW 1

SPMAK-SC1-D22 22 8-1.25MM LOCK NUT 1

SPMAK-SC1-D23 23 CONNECTING PLATE 1

SPMAK-SC1-D24 24 SCREW 1

SPMAK-SC1-D25 25 8-1.25MM LOCK NUT 1

SPMAK-SC1-D26 26 REAR CASTER SUPPORT ASSEMBLY 1

SPMAK-SC1-D27 27 8-1.25MM LOCK NUT 4

SPMAK-SC1-D28 28 CASTER 4

SPMAK-SC1-D29 29 8-1.25X60MM SOCKET HEAD BOLT 4

SPMAK-SC1-D30 30 PUSH STICK 1

SPMAK-SC1-D31 31 OPEN END WRENCH 1

SPMAK-SC1-D32 32 4MM HEX WRENCH 1

SPMAK-SC1-D33 33 5MM HEX WRENCH 1

SPMAK-SC1-D34 34 6MM HEX WRENCH 1

SPMAK-SC1-D35 35 8MM HEX WRENCH 1

56
 9 Wiring Diagram

9 Wiring Diagram

WIRING DIAGRAM
3-Wire 110V 1Phase

57
 10 Terms of Warranty

10 Terms of Warranty

MAKSIWA assures the owner that their equipment, identified by the Serial number issued on the Warranty Terms.

The equipment under warranty, for two (2) years, is as followed:

1. The warranty period begins on the date of the Warranty Terms below.
2. Within the warranty period, the manual labor and the components replaced by manufacturing defect will be
provided for free if duly proved by Maksiwa Service.
3. Third-party manufacturing equipment that makes up the MAKSIWA equipment (such as motors, electrical
equipment, belts etc.) are subject to the terms and conditions of warranty of their respective manufacturers.
4. In case an exchange of machine is needed, please return the defective part or machine to MAKSIWA.
5. All workplace adaptations for the equipment are under the responsibility of the machine owner.
6. If you notice any defect or malfunction when receiving the equipment, get in touch immediately with the
manufacturer or Dealer. Do not turn it on.
7. Not included in this warranty is any technical visits aimed at cleaning or adjustments caused by wear,
resulting from normal use of the equipment.
8. The warranty does not cover problems caused by mistreatment, carelessness, misuse or inappropriate
use of the functions designed for this equipment in this manual, as well as poorly executed operations by
untrained operators to operate it.
9. MAKSIWA is not responsible for lost productivity, direct or indirect damages caused to the owner of the
equipment or to third parties, or any other expense, including lost profits.
10. Even under warranty, you may lose its validity as follows:
a) Application of non-original components;
b) Alteration of its original features;
c) Lack of proper maintenance;
d) Improper use of the equipment;
e) Change in equipment or electronic connections;
f) Damage caused by mechanical shock or exposure to unsuitable conditions (humidity, salt spray, corrosive
agents, etc.);
g) Damage caused by bad weather (floods, flooding, lightning, power outages etc.);
h) Maksiwa is not responsible for damages to electrical components cause by power variation in your area.

For your safety, trust the repairs, maintenance and adjustments (including inspection and replacement) for
technical assistance recommended by MAKSIWA, always use genuine spare parts and accessories, reassembling
to its original machine the same way.

MODEL: SERIAL NUMBER: DATE: LOT NUMBER:

58
Imported by:
Maksiwa International Inc.
4100 N Powerline Rd, Suite D3
Pompano Beach, Florida
ZIP Code: 33073
Telephone: +1 (754) 205-6717 | Call us free: +1 (844) 319-6594
E-mail: [email protected]
www.maksiwa.com

59