Microbrain ITS-TX3 barrier gate arm opener trigger sensor User Manual (installation)
Uploaded by
josepherik1970Microbrain ITS-TX3 barrier gate arm opener trigger sensor User Manual (installation)
Uploaded by
josepherik1970Oblique-mounted trigger radar
User Manual
Please carefully read this manual before installation
Please carefully read this manual
before installation
Thank you for purchasing our radar products. To
ensure that the radar can achieve optimal perfor-
mance, please read this user manual carefully and
install and operate strictly according to the
manual.
The copyright of this product's hardware, software
design, etc. is protected by law and shall not be
infringed by any unit or individual.
In order to further improve the quality and
performance, the specifications and design of this
product may be changed without notice. Please
understand without further notice.
1
Content
1.Introduction...................................... 3
2.Technical Specifications................ 4
3.Features.............................................. 5
4.Installation Instructions.................. 6
5.Cable interface Definition............. 8
6.Configuration Instructions............. 9
7.Precautions......................................... 11
2
1.Introduction
The oblique-mounted trigger radar is developed for
the application needs of entrance and exit
management in parking lots and underground
garages. It can detect whether there are typical targets
such as cars and pedestrians in the entrance and exit
areas in various complex environments, thereby
guiding the camera system to complete functions such
as license plate recognition of incoming vehicles;
ITS-TX3 radar adopts a highly integrated solution, with
the
characteristics of small size, high precision, simple
debugging and installation, and high stability.
The barrier gate arm opener radar adopts a highly
integrated RF chip SoC
solution, which has the characteristics of small size, low
cost, all-day and all-weather operation, high detection
sensitivity, high accuracy, simple debugging and
installation, and stable and reliable.
The radar operates at a frequency of 79GHz and uses
a linear frequency modulation continuous waveform.
The available bandwidth is up to 3.3GHz, and the
distance resolution can reach 4cm. The millimeter
wave antenna adopts a multi-transmit and
multi-receive mode, which has a high angular
resolution and angle measurement accuracy. Through
the joint optimization design of software and
hardware, this product can accurately identify and
3
distinguish targets such as people and vehicles in the
parking lot entry and exit area, and guide the camera
system to perform license plate recognition.
3
2.Technical Specifications
Feature Parameter Technical indicators
9-24V
Operating Voltage
(12V/1A)
Operating
temperature -40℃~ +85℃
System Power < 0.5W
Properties
Protect level IP55
Communication
interface RS485；Bluetooth
Shell Size 107.6*73.3*18.3mm
3-6m configurable,
Horizontal width
Detect default 4m
Range 3-6m configurable,
Vertical length
default 6m
Upgrade Online debug 485；Bluetooth
& debug Online upgrade 485；Bluetooth
4
3.Features
The appearance of the radar is shown in Figure 1. Its main
features are:
. LED indicator：
There are two LED indicators on the front of the sensor. The
red one is the power light, which stays on after the power is
turned on; the green one is the status light, which turns on
when a target is detected in the area and turns off when the
target disappears；
. Detection area configuration:
The default sensing area of the sensor is 3 meters forward, and
different detection areas can be set through the mobile phone
app or computer debugging software;
. Configuration parameter saving:
Can automatically save the detection area and other
configurations, and use the most recently saved configuration
parameters after power failure and restart;
. Firmware upgrade:
No need to disassemble and install, upgrade the firmware
online through 485/Bluetooth interface, and restart the sensor
after the upgrade is completed to take effect;
. Stable performance:
The sensor operation is not affected by external environment
such as light, dust, rain and snow.
Figure 1. Appearance and dimensions of barrier radar products
5
4.Installation Instructions
This gate arm opener radar needs to be installed on
the barrier gate box or stand pole (as shown in Figure
2). The installation
steps are as follows:
Figure 2. Schematic diagram of radar installation location
6
The trigger radar is installed on the side of the barrier
gate or on the stand pole, and the radar beam is
directed to the best recognition area for the camera to
take pictures.
Trigger radar installation steps:
1. Radar installation position
The radar is 0.65-0.75m from the ground; the front of
the radar is consistent with the camera recognition
area, and ensure that there are no obstacles in the
radar detection area. If the green light flashes or is
always on, fine-tune the installation height and find a
position where there is no detection target and the
green light is off as the installation hole position;
2. Radar detection range setting
The maximum radar trigger distance is set to 6m. The
trigger area can be set according to the actual
environment. It is recommended to cover the optimal
recognition area. The horizontal width detection is
recommended to be 0.5m narrower than the road
width.
7
5.Cable interface definition
No Ca b le ID Colo r Description
1 12V Red Positive
2 G ND Bla c k Negative
3 B - /R X White 485 B-
4 A+ / T X Gra y 485 A+
5 NO Bl u e No r m a l l y o p e n 1
6 NO Green No r m a l l y o p e n 2
6 NC Brown No r m a l l y cl o s e
6 NC Pu r p l e No r m a l ly
The wiring harness functions and connection
relationships are as follows:
Power connection
The red wire "12V" is connected to the positive output
terminal of the 12 V power supply;
▲ The black wire "GND" is connected to the negative output
terminal of the 12 V power supply
Barrier Gate lever control signal
▲ The green and blue wires are normally open signals of the
relay, connecting the ground sensor coil terminal and the
common terminal (not distinguishing between positive and
negative) of the barrier gate control box.
48 5 cable connection
▲ The gray wire is connected totheT/R+ terminal of the 485 wire;
▲ The white wire is connected totheT/R- end of the 485 wire.
Bluetooth connection
▲ Bluetooth name: "Radar..." or "Mbit...";
User password: 88888888.
8
6.Configuration Instructions
The barrier gate arm opener radar can be debugged
through the mobile app. How to download the
mobile app:
Mobile App configuration:
After installing the mobile debugging app, openthe software
and click Connect Device.After the radar is successfully
connected, the interfacewill be shown in Figure 4.
Figure4 Figure5
9
After the connection is successful, click to setthe radar
parameters, as shown in Figure 5, and enter the radar
debugging interface, as shown in Figure 6.
Figure6 Figure7
You can set the installation method and trigger distance
according tothe actual environment onsite.After the
settings are completed, click Save as shown in Figure 7.
Figure8 Figure9
10
7.Precautions
The powersupplyvoltage isstabletoavoidaffectingthe
performanceoftheradar. It is recommendedtousea
separateexternal12V/1Apoweradapterforpowersupply.
. The radarantenna is integratedinside.Whentheradarsurface
iscoveredwithforeign matter(suchaswaterdroplets,frost,
rain,snow,dust,etc.), itaffectsthe normaloperationofthe
radar andshould becleanedintime.
Afterthedetectionenvironmentchanges(suchas installing
guide columns, icecreamcones,etc. inthedetectionarea),
please re-learnand recordtheenvironment.
The radar'sdetectionfieldofviewcannothaveobjectsthat
affecttargetdetection(suchasmetalfences, billboards, license
platerecognitioncameras,walls,etc.)toavoidinterference
withthe radar.
This product isnot recommendedtobedeployedon muddy
roads. Extremeweather(heavyrain, heavysnow) mayaffect
thestabilityoftheradar performance.
Ifyouneedto installthe radar inaspecialenvironment,please
contactourcompanyfirst,andthen installitcorrectly
according tothesuggestions.
11
Common fault description:
Faultphenomenon:Thegreenlightdoesnot lightupwhena
personstands infrontofthe radar.
Possible cause:Thehuman-vehicledistinctionfunctionis
enabled.Afterthevehicletriggersthe radargreen light,the
radarstartstodetect human-vehicle indistinguishable
detection.
Fault phenomenon:Afterthe radar isconnectedtothe12V
powersupplyofthecameracontrolboard,the red light
flashesandthepowersupply isinsufficient.
Possiblecause: It is recommendedtoconnectanexternal
12V-1Apoweradapterfor powersupply.
8.Packing list
No Parts QTY
1 Radarsensor 1
2 M16 Nut 1
3 Gasket 1
4 Wire harness 1
5 Certificate 1
6 User Manual 1
12
