Basics Handover 1
Uploaded by
virmajesitaBasics Handover 1
Uploaded by
virmajesitaHandover
in
Mobile systems
Agenda
• Introduction
• Handover theory
• GSM Handover
• UMTS Handover
• Inter RAT Handover
• Handover and performance
Introduction
What is Handover (Handoff)?
• Changing the point of connection while communicating
• In another words:
When a mobile user travels from one area of
coverage or cell to another cell within a call’s duration
the call should be transferred to the new cell’s base
station
Why handover is needed?
• Mobility
• User preferences
Introduction – Use Case 1
BSC
BS1 BS2 BS3
1.
2.
4. Connectout
Moving to BS1
3. Conversation BS1’s
and start
ofended
BS2’s – stillconversation
coveragewithin
– connect BS2
BS3’s coverage
to BS3
Tor K Moseng, Handoff in Wireless Internet Access
Handover
• When will a handoff occur?
• Initiated when received signal level drops below a certain
threshold value.
• Not as simple as it seems
• Actually consider a time average of the received signal instead of
the instantaneous level.
Handover Theory
• Define
• PMIN_USABLE as the minimum usable signal
level
• PHANDOFF as the threshold received signal
level at which a handoff will be initiated
• ∆ = PHANDOFF – PMIN_USABLE
Handover
• Must optimize ∆.
• Too large => too many handoffs
• Too small => too many lost calls
• Value of ∆ depends on
• Environment
• Expected mobile speeds
• Time required to perform a handoff
Handover- Successful
Handover- Unsuccessful
Handover in GSM
Horizontal Handover
Handover in GSM
Network-controlled, mobile terminal assisted handover
The network takes the handover decisions
The mobile terminal supervises and reports its signal quality
MSC
Four types of handover
Intra BTS handover BSC
MSC
Intra-BSC handover
BSC BSC
Inter-BSC handover
Inter-MSC handover
Tor K Moseng, Handoff in Wireless Internet Access
Intra BTS Handover
• The ME remains attached to the BTS transciever.
• Changing just the frequency or the slot used by the ME
Intra BSC Handover
• Or named as Inter BTS Handover
• Occures when moving from one BTS coverage area into another BTS
• Both BTS are controlled by the same BSC
• The BSC assigns the new channel and slot for the ME.
Inter BSC Handover
• Occures when moving from one BTS coverage area into
another BTS.
• Both BTS are controlled by different BSC.
• This Handover is manged by the MSC
Inter MSC Handover
• Occures when moving from one BTS coverage area into another BTS.
• Both BTS are controlled by different BSC.
• Both BSC are controlled by different MSC.
• The two MSC negotiate to handle the handover.
Handover in UMTS
For purely inter W-CDMA technology, there are three
basic types of handover:
• Hard Handover
• Soft Handover
• Softer Handover
Hard Handover
• Break Before Make
• The network decides a handover is required dependent upon
the signal strengths of the existing link, and the strengths of
broadcast channels of adjacent cells.
• The link between the existing NodeB and the UE is broken.
• A new link is established between the new NodeB and the UE.
Soft Handover
• Occures when the ME is moving in the overlaping coverage
area.
• The ME communicate and recieve the signals from the
NodeB’s which their signals are overlaping.
• The rake reciever is needed in the UE (ME) to combine the
two signals
• In the uplink , the best quality frame of the two signals is
selected. The selection is made by the outer loop power control
algorithm measurment.
• Negatives: It need to indicate rescources(capacity) on both
NodeBs
Softer Handover
• Softer handover is a special case of soft handover where the
radio links that are added and removed belong to the same
Node B.
• In softer Handover , the NodeB can receive the signal in macro
diversity with maximum ratio combining.
• In soft handover macro diversity with selection combining is
selected.
Handover between GSM-WCDMA
• Limited UMTS coverage
• UMTS network busy whereas spare capacity is available on GSM
network
• Two types of Inter RAT handover:
1-GSM to UMTS
2-UMTS to GSM
UMTS to GSM handover
1- Compressed mode handover: Using compressed mode handover the
UE uses the gaps in transmission that occur to analyse the reception of
local GSM base stations. The UE uses the neighbour list provided by
the UMTS network to monitor and select a suitable candidate base
station. Having selected a suitable base station the handover takes
place, but without any time synchronisation having occurred.
2- Blind handover: This form of handover occurs when the base station
hands off the UE by passing it the details of the new cell to the UE
without linking to it and setting the timing, etc of the mobile for the
new cell. In this mode, the network selects what it believes to be the
optimum GSM based station. The UE first locates the broadcast
channel of the new cell, gains timing synchronisation and then carries
out non-synchronised intercell handover.
GSM to UMTS
• Handover from GSM to UMTS : This form of handover is supported
within GSM and a "neighbour list" was established to enable this occur
easily. As the GSM / 2G network is normally more extensive than the 3G
network, this type of handover does not normally occur when the UE leaves
a coverage area and must quickly find a new base station to maintain contact.
The handover from GSM to UMTS occurs to provide an improvement in
performance and can normally take place only when the conditions are right.
The neighbour list will inform the UE when this may happen.
Handoff and performance
• Handoffs are expensive to execute, so unnecessary handoffs should
be avoided.
• If the handoff criteria are not chosen appropriately, then in the
overlapping region between the two BS coverage area boundaries,
the call might be handed back and forth several times between them.
• If the criteria are too conservative, then the call may be lost before
the handoff can take place.
• The handoff decision-making criteria become even more critical
with the evolution to smaller cell sizes, which is happening to
increase the capacity of systems and to reduce power requirements of
MSs.
• Unreliable and inefficient handoff procedures will reduce the quality
and reliability of the system.
Handoff Failures
• The reason of handoff failures
• No channel is available on selected BS.
• Handoff is denied by the network for reasons such as
lack of resources. For example, no bridge or no
suitable channel card; the MS has exceeded some limit
on the number of handoffs that may be attempted in
some period of time.
• It takes the network too long to set up the handoff after
it has been initiated.
• The target link fails in some way during the execution
of handoff.
Q&A
Thank You
