F 3349 (0602)

F 3349

F 3349: 8-channel output module

safety-related, applicable up to SIL 3 according to IEC 61508
• resistive or inductive load up to 500 mA (at L+ 24 V or 48 V)
• lamp load up to 10 W
• with integrated safety shutdown
• with safe isolation, with line monitoring

d32 24 V
z2 EL+
z4 WD
I/O bus

d2 L-
d30
z30
d6
z6

Z 7150 / 3349 / C5
L-

L-
b18

b20

b22

b24

b10
b26

b12
b28

b14
b30

b16
b32
z10

z22

z24

z26

z28

z12
z32

z14
z18
z20
b2

b4

b6

b8
z8

z2
z4

z6

Z 7150 / 3349
Front
- cable plug
+
24 V or 48 V

Figure 1: Block diagram and front cable plug

Appertaining function block: HB-BLD-3 or HB-BLD-4

The module is automatically tested during operation. The main test routines are:
• Reading back of the output signals. The operating point of the 0-signal read back
is ≤ 6.5 V,
• Switching capability of the safety shutdown, cross-talking (walking-bit test),
• Line monitoring.

Nominal output voltage 24 V or 48 V, acc. to supply of L+ via cable plug,

500 mA, short-circuit-proof
Space requirement 4 SU
Operating data 5 VDC / 0.15 A,
24 VDC / 200 mA (via rear bus system)
24/48 VDC / 50 mA plus load (via cable plug)

All rights reserved. Equipment subject to change without notice: 1/4

HIMA Paul Hildebrandt GmbH + Co KG, P.O. Box 1261, 68777 Brühl
F 3349 (0602)

Cable plug for outputs 24 VDC

Channel Connection Color
1 b2 BN
b18 WH
2 b4 YE
b20 GN
3 b6 PK
b22 GY
4 b8 RD
b24 BU
5 b10 VT Cable
b26 BK LiYY 16 x 0.5 mm2
6 b12 WHGN
b28 WHBN
7 b14 WHGY
b30 WHYE
8 b16 WHBU
b32 WHPK
L- 24 V z2 BK Flat pin plug 6.3 x 0.8 mm
L+ 24 V z12 RD
Wire: q = 1 mm2, l = 750 mm

Lead marking of the cable plug Z 7150 / 3349 / C5 / 24P2

2-pole connection of the load
Figure 2: Lead marking of the cable plug for outputs 24 VDC

Cable plug for outputs 48 VDC

Channel Connection Color
1 b2 BN
b18 WH
2 b4 YE
b20 GN
3 b6 PK
b22 GY
4 b8 RD
b24 BU
5 b10 VT Cable
b26 BK LiYY 16 x 0.5 mm2
6 b12 WHGN
b28 WHBN
7 b14 WHGY
b30 WHYE
8 b16 WHBU
b32 WHPK
-48 V z2 BN Cable
+48 V z12 WH
LiYY 2 x 1 mm2

Lead marking of the cable plug Z 7150 / 3349 / C5 / 48P2

2-pole connection of the load
Figure 3: Lead marking of the cable plug for outputs 48 VDC

2/4
F 3349 (0602)

b18

b16

b32
z28

z32

z12
b2

z4

z2
10 W

* required with
inductive load

2-pole connection of the loads required!

Figure 4: 2-pole connection

Additional technical data

Current input WD 1 mA
Monitored switching time max. 200 µs (without extension by
the function block)

Internal voltage drop max. 2 V at 500 mA load

Admissible line resistance max. 11 Ω
max. lamp load 10 W
max. inductivity 1H
max. capacity 100 µF
Output leakage current max. 500 µA
Operating points of the line moinitoring
Line short-circuit 0.7...0.8 A
Line break 2...8 mA

Reaction of the module to errors

• Module error:
A outputs are switched off.
• Line error:
If an external line break or a short-circuit is detected, the module only makes an
annunciation.
At a line break and an overcurrent > 0.2 A the overcurrent tripping is activated after at
last 50 ms. For smaller overloads (> 0.7 A) the reaction time can last up to several
seconds.
After every approx. 4.5 seconds the channel of the module is reconnected again.
• The error codes for the module are shown in the display of the corresponding central
module. For further informations see operating system manual.

3/4
F 3349 (0602)

Engineering notes
• In case of line monitoring the appertaining function blocks HB-BLD-3 (for single chan-
nel operation) or HB-BLD-4 (for redundant operation) enable enhanced configuration
possibilities for the module.
• The extension of the time for the inrush current for lamp loads by the appertaining
function block is valid for all channels. So inductive and lamp loads may not be opera-
ted on one module at the same time.
• The line break monitoring requires an output load of at least 10 mA.
• The short-circuit and line break can be evaluated in the user program as line faults by
means of the function blocks HB-BLD-3 or HB-BLD-4. The evaluation of the signal “line
break” is made up to SIL 1.
• The outputs of the module and their supply voltage must be connected with two poles.
The use of common lines can produce coupling loops with interferences, including a
module fault or a failure of the safety shutdown of the outputs.
• The outputs can be connected in parallel without additional external decoupling diodes.
• An external short-circuit of a channel does not trigger the integrated safety shutdown,
i. e. the remaining channels continue their function.
• If the line is longer than 10 m or if a power supply unit not manufactured by HIMA is
used, for a faultless operation with 48 V the supply voltage must be filtered with an
additional module Z 6019.
• Lines for outputs not used may not be extended to the plant without any termination
loads.
• In one I/O subrack max. 10 output modules with nominal load may be used.
• At maximum power dissipation a forced cooling with a fan module is required.

Note for the redundant use of modules

• In case of a line short-circuit the double current can flow, until this line short-circuit is
diagnosed.
• In case of a line break the required minimum current is twice the value (20 mA) to pre-
vent an indication of a line break.

Note The connection of capacitive loads is not permitted. A length of the

connection line up to 3 km is possible. The line capacity, however, is
limited to a maximum of 1 µF.
With an interruption of the supply line L- the safe shutdown of the out-
puts is no longer ensured.

4/4