3000 Series 3 Error Code List Page 1 of 23

Error Code List

HELP MENU

To search enter an error code:-

Search

A ABS
C Fastrac Central Controller (ECU1)
D EMS Dashboard
H Auxiliary Controls ECU (Hydraulic Controls)
K Engine
M Work Lights
P DECU (Touch Screen Panel)
R Rear Hitch
S Suspension
T Gearbox 6x4
U Front Hitch
V Green Spool Valve
W Blue Spool Valve
X Brown Spool Valve
Y Grey Spool Valve

ABS ECU
A2194 Internal checksum failure
A2195 EEPROM compatibilty failure
A2196 EEPROM checksum error
A2197 Invalid fault code in the DTC container Overwitten secured variable
A2198 EEPROM can not be written
A2199 ECU HW not compatible with the drive SW
A2200 BSL SW not compatible with the drive SW
A2201 CAN message missing
A2203 Front Left Wheel (S-E) Open circuit or Shorted to Battery
A2204 Rear Right Wheel (S-D) Open circuit or Shorted to Battery
A2205 Rear Left Wheel (S-C) Open circuit or Shorted to Battery
A2207 Front Right Wheel (S-F) Open circuit or Shorted to Battery
A2210 Rear Left Wheel (S-C) Shorted to Ground
A2211 Rear Right Wheel (S-D) Shorted to Ground
A2212 Front Left Wheel (S-E) Shorted to Ground
A2213 Front Right Wheel (S-F) Shorted to Ground
A2216 Rear Left Wheel (S-C) Frequency > 15KHz
A2217 Rear Right Wheel (S-D) Frequency > 15KHz
A2218 Front Left Wheel (S-E) Frequency > 15KHz
A2219 Front Right Wheel (S-F) Frequency > 15KHz
A2222 Rear Left Wheel (S-C) speed jump to zero

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 2 of 23

A2223 Rear Right Wheel (S-D) speed jump to zero

A2224 Front Left Wheel (S-E) speed jump to zero
A2225 Front Right Wheel (S-F) speed jump to zero
A2228 Rear Left Wheel (S-C) sensor airgap
A2229 Rear Right Wheel (S-D) sensor airgap
A2230 Front Left Wheel (S-E) sensor airgap
A2231 Front Right Wheel (S-F) sensor airgap
A2234 Rear Left Wheel (S-C) sensor airgap (no signal)
A2235 Rear Right Wheel (S-D) sensor airgap (no signal)
A2236 Front Left Wheel (S-E) sensor airgap (no signal)
A2237 Front Right Wheel (S-F) sensor airgap (no signal)
A2240 Rear Left Wheel (S-C) damaged sensor ring
A2241 Rear Right Wheel (S-D) damaged sensor ring
A2242 Front Left Wheel (S-E) damaged sensor ring
A2243 Front Right Wheel (S-F) damaged sensor ring
A2246 Rear Left Wheel (S-C) Wheel diameter incorrect
A2247 Rear Right Wheel (S-D) Wheel diameter incorrect
A2248 Front Left Wheel (S-E) Wheel diameter incorrect
A2249 Front Right Wheel (S-F) Wheel diameter incorrect
A2250 P21 Backup Solenoid electrical error
A2251 P21 Load Solenoid electrical error
A2252 P21 Exhaust Solenoid electrical error
A2253 P22 Backup Solenoid electrical error
A2254 P22 Load Solenoid electrical error
A2255 P22 Exhaust Solenoid electrical error
A2256 P2 Backup / Hold Solenoid electrical error
A2257 CAN data missing
A2258 P2 Exhaust Solenoid electrical error
A2260 Too long ATC brake control activity
A2261 ATC disturbed wheel speed
A2262 J1939 wheel diameter out of range
A2266 Too long ATC brake control activity
A2267 ATC disturbed wheel speed
A2268 J1939 wheel diameter out of range
A2270 Hill Hold is active due to fault condition
A2291 ABS pressure control valve front axle hold solenoid fault
A2299 ABS pressure control valve front axle release solenoid fault
A2307 ATC information lamp open circuit fault
A2428 P1 Pressure sensor electrical error
A2429 P1 Pressure dynamic error
A2430 P4 Pressure sensor electrical error.
A2431 P4 Pressure dynamic error
A2432 P42 Pressure sensor electrical error
A2433 P42 Pressure dynamic error
A2434 P21 Pressure sensor electrical error
A2435 P21 Pressure dynamic error
A2436 P22 Pressure sensor electrical error
A2437 P22 Pressure dynamic error
A2438 Catastrophic error
A2439 Safety Controller: illegal interrupt occured
A2440 Safety Controller: illegal reset occurred
A2441 Safety Controller: romtest error
A2443 Safety Controller: stack overflow
A2444 Safety Controller: stack underflow

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 3 of 23

A2445 Safety Controller: ALU error

A2446 Safety Controller: ramtest error
Safety Controller: number of ICC communications in 1 second out of
A2447
range
Safety Controller: time between 2 ICC data telegrams too long or too
A2448
short
A2449 Safety Controller: intercontroller communication: timeout occurred
A2450 Safety Controller: intercontroller communication: checksum error
A2452 Pressure Sensor Cross Check: ADC values implausible
A2479 High Voltage; greater than 32 volts
A2482 Low Voltage; disable system functions
A2483 Low Voltage whilst moving; disable system functions
A2484 System pressure below 2.5 bar
A2485 System pressure below 2.5 bar while moving
A2493 Too long Service Brake application
A2495 Valve Plausibility Monitoring: Illegal valve activation detected
Valve Plausibility Monitoring: ABS activation; detected in Safety
A2496
Controller
A2498 Valve Plausibility Monitoring: Dynamic fault
A2527 Acceleration sensor selftest failure; sensor is broken
A2554 P21 Leakage
A2555 P21 Uncontrollable
A2556 P21 Backup Valve
A2557 P22 Leakage
A2558 P22 Uncontrollable
A2559 P22 Backup Valve
A2560 P2 Leakage
A2561 P2 Uncontrollable
A2562 P1 Implausible
A2581 Voltage supply line resistance high
A2582 Ground missing on BCAG Power connector pin3.
A2583 Valve supply missing
A2586 EEPROM Configuration is corrupted
A2587 Main ABS configuration is inconsistent
A2588 Configuration of auxiliary IO & functions is inconsistent
A2589 Intercontroller communication: checksum error
A2590 ABS activity too long (addinfo = 0) or too frequent (addinfo = 1)
A2591 Default config in FLASH corrupted (checksum error)
ECU has not been configured for the ABS or ABS/Hill Hold/Traction
A2601
Control option.
A2602 The automated ABS system test has not been run, and passed.
A2607 P28 Load Solenoid electrical error
A2609 AUX3 internal charge-pump error
A2610 AUX3 internal charge-pump error (EM supply)
Valve Plausibility Monitoring: ABS activation; detected in Main
A2611
Controller
A2612 Valve supply missing
A2615 EBM in Factory Test Mode; don't use on public roads

A C D H K M P R S T U V W X Y

Ý
Top

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 4 of 23

Fastrac Central Controller - ECU1

C0000 General FCC error
C0100 FCC flow divider solenoid driver over current
C0109 FCC theoretical ground speed driver open circuit
C0110 FCC True ground speed driver open circuit
C0120 FCC battery voltage too low
C0121 FCC battery voltage too high
C0122 FCC sensor reference voltage too low
C0123 FCC sensor reference voltage too high
C0130 Valveblock Pilot Valve driver Open circuit
C0131 Valveblock Pilot Valve driver short circuit
C0132 Pilot Valve driver fault
C0150 Valve Block Pressure sensor open circuit
C0151 Valve Block Inlet Pressure Sensor signal low
C0152 Valve Block Inlet Pressure Sensor output high
C0170 Four Wheel Drive Open Circuit
C0171 Four Wheel Drive Over Current
C0172 Four Wheel Drive General Fault
C0175 Diff Lock Open Circuit
C0176 Diff Lock Over Current
C0177 Diff Lock General Fault
C0180 Rear fender spool control switch “in range fault”
C0181 Rear fender spool control switch “out of range fault”
C0182 Rear fender spool control switch “Ignition on operation fault”
C0183 Rear fender spool control switch “Operating time exceeded”
C0190 Front PTO Stop Switch “Ignition on operation fault”
C0191 Front PTO Stop Switch “Operating time exceeded”
C0192 Rear PTO Stop Switch “Ignition on operation fault”
C0193 Rear PTO Stop Switch “Operating time exceeded”
C0194 Front Hitch Raise Switch “Ignition on operation fault”
C0195 Front Hitch Raise Switch “Operating time exceeded”
C0196 Front Hitch Lower Switch “Ignition on operation fault”
C0197 Front Hitch Lower Switch “Operating time exceeded”
C0200 FCC loaded an EEPROM value during power up
C0202 FCC Software Fault
C0203 FCC service master setup invalid
C0205 PTO Front Brake Solenoid Open Circuit
C0206 PTO Front Brake Solenoid Short Circuit
C0207 PTO Front Brake General Fault
C0210 PTO Front Clutch Solenoid Open Circuit
C0211 PTO Front Clutch Solenoid Short Circuit
C0212 PTO Front Clutch General Fault
C0213 PTO Front Clutch Circuit: output over range
C0214 PTO Front Clutch Circuit: Output under range
C0220 PTO Rear Brake Solenoid Open Circuit
C0221 PTO Rear Brake Solenoid Short Circuit
C0222 PTO Rear Brake General Fault
C0225 PTO Rear Clutch Solenoid Open Circuit
C0226 PTO Rear Clutch Solenoid Short Circuit
C0227 PTO Rear Clutch General Fault
C0228 PTO Rear Clutch Circuit: Output over range
C0229 PTO Rear Clutch Circuit: Output under range
C0235 PTO Control Message from DECU Timeout
C0236 PTO Control Message from DECU Plausibility Error
C0237 Front PTO Configuration Change While PTO Running
C0238 PTO Speed Selection Lever moved when PTO running
C0239 Front PTO speed hasn’t increased when PTO ‘On’
C0240 PTO 540/1000 Selector Position Sensor: signal under range error

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 5 of 23

C0241 PTO 540/1000 Selector Position Sensor: signal in range error

C0242 PTO 540/1000 Selector Position Sensor: invalid position
C0243 PTO 540/1000 Selector Position Sensor: invalid position
C0244 PTO 540/1000 Selector Position Sensor: invalid position
C0245 PTO 540/1000 Selector Position Sensor: invalid position
C0246 PTO 540/1000 Selector Position Sensor: invalid position
C0247 PTO 540/1000 Selector Position Sensor: signal over range error
C0248 PTO Calibration General Fault
C0249 PTO Calibration Failed
C0250 Rear PTO speed hasn't increased when PTO ‘On’
C0251 Front PTO speed present when PTO ‘Off’
C0252 Rear PTO speed present when PTO ‘Off’
C0253 PTO 540/1000 Calibration Required

A C D H K M P R S T U V W X Y

Ý
Top

EMS Dashboard
D0002 EMS Memory Error
D0003 EMS CanBus switched off due to error
D0004 EMS executed COP watchdog reset
D0005 EMS Application ROM Error
D0006 EMS ROM memory error
D0042 EMS detected vehicle voltage exceeded 16V
D0101 Software Error
D0102 Software Error
D0103 Software Error
D0104 Software Error
D0105 Software Error
D0106 Software Error
D0224 Engine oil pressure low with engine running
D0227 Air Filter Blocked
D0228 Trailer ABS fault
D0229 Alternator not charging (engine speed over 1000rpm)
D0230 Brake fluid level low
D0231 Air tank 1 pressure low
D0232 Air tank 2 pressure low
D0233 Air tank 3 pressure low
D0234 Handbrake on when moving
D0236 Radar speed signal inconsistent with Gearbox speed
D0240 EMS has reset due to CanBus error
D0250 EMS Clutch fluid level low

A C D H K M P R S T U V W X Y

Ý
Top

Auxiliary Controls ECU

H0001 Auxiliary Controls ECU EEPROM Error
H0002 Auxiliary Controls ECU EEPROM Error

Engine ECU
K0122 Boost pressure sensor voltage above normal or open circuit

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 6 of 23

K0123 Boost pressure sensor voltage below normal

K0131 Throttle 1 sensor above normal or open circuit (IDLE)
K0132 Throttle 1 sensor below normal (IDLE)
K0135 Oil pressure sensor voltage above normal or open circuit
K0141 Oil pressure sensor voltage below normal
K0143 Oil pressure LOW
K0144 Coolant temp sensor voltage above normal or open circuit
K0145 Coolant temp sensor voltage below normal
K0146 Coolant temperature ABOVE NORMAL (>106C)
K0151 Coolant temperature HIGH, ALARM (>113C)
K0153 Intake air temp sensor voltage above normal or open circuit
K0154 Intake air temp sensor voltage below normal
K0221 Ambient pressure sensor voltage above normal or open circuit
K0222 Ambient pressure sensor voltage below normal
K0284 Internal 12V supply voltage below normal
K0322 Solenoid valve 1, Current below normal: Open circuit
K0323 Solenoid valve 5, Current below normal: Open circuit
K0324 Solenoid valve 3, Current below normal: Open circuit
K0325 Solenoid valve 6, Current below normal: Open circuit
K0331 Solenoid valve 2, Current below normal: Open circuit
K0332 Solenoid valve 4, Current below normal: Open circuit
K0387 Internal 12V supply voltage above normal
K0415 Oil pressure LOW, ALARM
K0449 Rail pressure above normal
K0452 Rail pressure sensor voltage below normal
K0488 Intake air temp ABOVE NORMAL (>90C)
K0553 Rail pressure ABOVE NORMAL
K0554 Rail pressure raw value is intermittent
K0559 Rail pressure below normal
K0753 Number and/or position of the camshaft pulses implausible - disturbed signal
K4005 Number of injections is limited by quantity balance of high pressure pump
K4020 Fuel main filter inlet pressure sensor voltage above normal or open circuit
K4021 Fuel main filter inlet pressure sensor voltage below normal
K4022 Water in fuel
K4023 Fuel main filter inlet pressure ABOVE NORMAL
K4024 Fuel main filter inlet pressure BELOW NORMAL
K4025 Fuel main filter inlet pressure ALARM, out of safe operating range
K4030 Oil pressure ABOVE NORMAL (>9,5 bar / 30C)
K4035 Boost pressure LOW
K4040 Intake manifold pressure drop too HIGH at cranking
K4050 Rail pressure sensor voltage above normal or open circuit
K4054 Rail pressure, Leakage detected by quantity balance
K4055 Rail pressure controller, Positive deviation
K4056 Rail pressure controller, Negative deviation
K4057 Rail pressure raw value is above maximum offset
K4058 Rail pressure raw value is below minimum offset
K4060 Battery voltage ABOVE NORMAL(>17V)
K4061 Battery voltage BELOW NORMAL (<78V)
K4062 Battery voltage sensor voltage above normal
K4063 Battery voltage sensor voltage below normal
K4070 Ambient temperature sensor voltage above normal or open circuit
K4071 Ambient temperature sensor voltage below normal
K4072 Ambient temperature sensor signal abnormal rate of change
K4075 Fuel temp sensor voltage above normal or open circuit
K4076 Fuel temp sensor voltage below normal
K4077 Fuel inlet temperature HIGH, ALARM (>85C)
K4079 Engine Speed ABOVE NORMAL
K4085 Grid heater relay voltage above normal or short to HIGH SOURCE
K4087 Grid heater relay current below normal or open circuit

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 7 of 23

Grid heater relay current above normal or short to GROUND

K4095 Bus off Vehicle CAN (250k)
K4102 Solenoid valve 1, Short circuit
K4103 Solenoid valve 1, Current above normal: Short circuit between cables
K4107 Solenoid valve 2, Short circuit
K4108 Solenoid valve 2, Current above normal: Short circuit between cables
K4112 Solenoid valve 3, Short circuit
K4113 Solenoid valve 3, Current above normal: Short circuit between cables
K4117 Solenoid valve 4, Short circuit
K4118 Solenoid valve 4, Current above normal: Short circuit between cables
K4121 Solenoid valve 5, Current above normal: Short circuit between cables
K4122 Solenoid valve 5, Short circuit
K4125 Solenoid valve 6, Current above normal: Short circuit between cables
K4127 Solenoid valve 6, Short circuit
K4131 Signal deviation between crankshaft and camshaft too large
K4132 Cam speed sensor signal missing
K4140 MPROP control, High side short circuit to HIGH SOURCE
K4141 MPROP control, Low side short circuit to GROUND
K4142 MPROP control, Low side short circuit to HIGH SOURCE
K4143 MPROP control, High side short circuit to GROUND
K4144 MPROP control, Open circuit
K4150 ECU Internal fault 0101 - MPROP control, Metering unit AD-channel voltage above normal
K4151 ECU Internal fault 0102 - MPROP control, Metering unit AD-channel voltage below normal
K4152 MPROP control, Powerstage over temperature
K4155 ECU temperature sensor voltage above normal or open circuit
K4156 ECU temperature sensor voltage below normal
K4157 ECU over temperature HIGH ALARM
K4170 ECU Internal fault 0100 - ECU internal power off ERROR at previous afterrun
K4171 Main relay early opening at previous afterrun
K4175 DEF tank level sensor voltage above normal or open circuit
K4176 DEF tank level sensor voltage below normal
K4178 DEF tank EMPTY
K4179 DEF tank LEVEL LOW
K4200 DEF tank temperature sensor voltage above normal or open circuit
K4201 DEF tank temperature sensor voltage below normal
K4203 DEF tank maximum defrost time exceeded
K4204 DEF tank temperature ABOVE normal
K4205 DEF tank temperature signal abnormal rate of change
K4220 Torque/Speed Control (TSC1) timeout
K4221 DEF dosing valve low side short circuit to HIGH SOURCE
K4222 DEF dosing valve high side short circuit
K4223 DEF dosing valve high side short circuit to HIGH SOURCE or open load
K4224 DEF dosing valve low side short circuit to GROUND or open load
K4225 DEF dosing valve powerstage driver chip over temperature
K4226 DEF dosing valve current abnormal behaviour
K4230 DEF tank heater coolant valve solenoid short circuit to HIGH SOURCE
K4231 DEF tank heater coolant valve solenoid short circuit to GROUND
K4232 DEF tank heater coolant valve solenoid open circuit
K4233 DEF tank heater ECU power stage over temperature
K4234 5Vdc Supply 1 voltage out of range
K4238 5Vdc Supply 2 voltage out of range
K4239 5Vdc Supply 3 voltage out of range
K4240 12V sensor supply 1 voltage above normal
K4241 12V sensor supply 1 voltage below normal
K4245 SCR system malfunction: NOx emission too HIGH
K4246 SCR system malfunction: Measured Nox emission implausible
K4248 Crank speed signal erratic, too much noise pulses
K4249 Crankshaft speed sensor signal missing
K4250 SCR system ERROR: DEF over pressure detected

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 8 of 23

SCR system ERROR: Pumped-Dosed quantities balance error

K4258 SCR system ERROR: Pressure drop test failure
K4260 SCR system ERROR: DEF dosing pressure above normal
K4261 SCR system ERROR: Emptying not completed at previous shutdown
K4262 SCR system ERROR: DEF dosing pressure below normal
K4263 DEF pressure sensor voltage above normal or open circuit
K4264 DEF pressure sensor voltage below normal
K4265 DEF suction line heater control circuit short circuit to HIGH SOURCE
K4266 DEF suction line heater control circuit short circuit to GROUND
K4267 DEF suction line heater control circuit open circuit
K4269 DEF suction line heater ECU power stage over temperature
K4270 DEF backflow line heater control circuit short circuit to HIGH SOURCE
K4271 DEF backflow line heater control circuit short circuit to GROUND
K4272 DEF backflow line heater control circuit open circuit
K4274 DEF backflow line heater ECU power stage over temperature
K4275 DEF supply module heater temperature signal in invalid range
K4276 DEF supply module heater control circuit short circuit to HIGH SOURCE
K4277 DEF supply module heater control circuit short circuit to GROUND
K4279 DEF supply module heater temperature signal in failure range
K4281 DEF supply module temperature measurement module is not reponding
K4282 DEF supply module heater ECU power stage over temperature
K4285 DEF pressure line heater control circuit short circuit to HIGH SOURCE
K4286 DEF pressure line heater control circuit short circuit to GROUND
K4287 DEF pressure line heater control circuit open circuit
K4288 DEF pressure line heater ECU power stage over temperature
K4290 DEF supply module heater relay low side open circuit
K4291 DEF supply module heater relay high side (heater, main relay) open circuit
K4292 DEF supply module heater relay open circuit
K4293 DEF suction line heater relay low side (line relay) open circuit
K4294 DEF suction line heater relay high side (heater, main relay) open circuit
K4295 DEF pump motor speed deviation
K4296 DEF pump motor speed permanent deviation
K4297 DEF backflow line heater relay low side (line relay) open circuit
K4298 DEF backflow line heater relay high side (heater, main relay) open circuit
K4299 DEF pump motor not available for actuation
K4300 DEF pump motor control signal short circuit to HIGH SOURCE
K4301 DEF pump motor control signal short circuit to GROUND
K4302 DEF pump motor control signal current below normal or open circuit
K4303 SCR catalyst inlet gas temp sensor value abnormal rate of change
K4304 SCR catalyst outlet gas temp sensor value abnormal rate of change
K4305 DEF pressure line heater relay low side (line relay) open circuit
K4306 DEF pressure line heater relay high side (heater, main relay) open circuit
K4307 SCR catalyst inlet gas temp sensor voltage above normal or open circuit
K4308 SCR catalyst inlet gas temp sensor voltage below normal
K4309 SCR catalyst outlet gas temp sensor voltage above normal or open circuit
K4310 SCR catalyst outlet gas temp sensor voltage below normal
K4311 DEF pump motor control powerstage over temperature
K4312 DEF pump direction valve low side short circuit to HIGH SOURCE
K4313 DEF pump direction valve low side short circuit to GROUND
K4314 DEF pump direction valve low side current below normal or open circuit
K4317 DEF pump direction valve low side control powerstage over temperature
K4335 SRC catalyst over temperature
K4340 SRC catalyst NOx sensors cross connected
K4341 SRC catalyst temperature sensors cross connected
K4500 Powerstages could be disabled due to high Battery voltage
K4501 Powerstages could be disabled due to low Battery voltage
K4505 Bus off Engine CAN (1M)
K4510 ECU Main Relay 0 Short circuit to HIGH SOURCE
K4511 ECU Main Relay 0 short circuit to GROUND

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 9 of 23

ECU Main Relay 1 Short circuit to HIGH SOURCE

K4513 ECU Main Relay 1 short circuit to GROUND
K4518 Rail PRV recognised as OPEN
K4520 Error in the plausibility of the injection energizing time
K4521 Error in the plausibility of the start of energising angles
K4525 ECU Internal fault 0103 - Chip error in the CY33x power stage component 0
K4530 ECU Internal fault 0105 - Diagnostic fault check to report the NTP error in ADC monitoring
K4531 ECU Internal fault 0106 - Diagnostic fault check to report the ADC test error
ECU Internal fault 0107 - Diagnostic fault check to report the error in Voltage ratio in ADC
K4532 monitoring
K4533 ECU Internal fault 0108 - Diagnostic fault check to report errors in query-/response-communication
K4534 ECU Internal fault 0109 - Diagnostic fault check to report errors in SPI-communication
ECU Internal fault 0110 - Diagnostic fault check to report multiple error while checking the
complete
K4535 ROM-memory
K4540 ECU Internal fault 0111 - Loss of synchronization sending bytes to the MM from CPU
ECU Internal fault 0112 - DFC to set a torque limitation once an error is detected before MoCSOP's
K4541 error reaction is set
K4542 ECU Internal fault 0113 - Wrong set response time
K4543 ECU Internal fault 0114 - Too many SPI errors during MoCSOP execution
K4544 ECU Internal fault 0115 - Diagnostic fault check to report the error in undervoltage monitoring
K4545 ECU Internal fault 0116 - Diagnostic fault check to report that WDA is not working correct
K4546 ECU Internal fault 0117 - OS timeout in the shut off path test Failure setting the alarm task period
K4547 ECU Internal fault 0118 - Diagnostic fault check to report that the positive test failed
K4548 ECU Internal fault 0119 - Diagnostic fault check to report the timeout in the shut off path test
K4549 ECU Internal fault 0120 - Diagnostic fault check to report the error in overvoltage monitoring
K4550 ECU Internal fault 0121 - Cy320 Multiple Power Supply module SPI/COM-Error
K4555 ECU Internal fault 0120 - Fast A/D Converter calibration error
K4560 Engine specification mismatch
K4570 Bad digital input configuration
ECU Internal fault 0128 - Diagnostic fault check to report "WDA active" due to errors in
K4575
query-/response communication
ECU Internal fault 0129 - Diagnostic fault check to report "ABE active" due to under voltage
K4576 detection
ECU Internal fault 0130 - Diagnostic fault check to report "ABE active" due to overvoltage
K4577 detection
ECU Internal fault 0131 - Diagnostic fault check to report "WDA/ABE active" due to unknown
K4578 reason
K4581 Injector bank 0 short circuit
K4585 Injector bank 1 short circuit
K4590 Rail PRV is forced to open; perform pressure increase
K4591 Rail PRV is forced to open; perform pressure shocK
K4592 Rail PRV reached maximum allowed opening count
K4593 Rail PRV reached maximum allowed open time
K4595 ECU Internal fault 0123 - Reported SPI and COM-Errors of a Cy146
K4596 Rail over pressure monitoring count exceeded
K4597 Rail over pressure monitoring time exceeded
K4598 ECU internal fault 0132
K4599 ECU internal fault 0133
K4600 DEF pump temperature signal duty cycle in invalid range
K4601 DEF pump temperature signal duty cycle in failure range
K4605 DEF heater main relay circuit short circuit to HIGH SOURCE
K4606 DEF heater main relay open circuit
K4607 DEF heater main relay ECU power stage over temperature
K4610 DEF pump direction valve high side short circuit to HIGH SOURCE
K4611 DEF pump direction valve high side short circuit to GROUND
K4612 DEF pump direction valve high side current below normal or open circuit
K4613 DEF pump direction valve high side control powerstage over temperature
K4615 DEF heater main relay control circuit short circuit to HIGH SOURCE
K4616 DEF heater main relay control circuit short circuit to GROUND

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 10 of 23

K4620 Downstream NOx sensor missing

K4621 Upstream NOx sensor missing
K4630 SCR system ERROR: DEF backflow line blocked or implausible
K4631 SCR system ERROR: DEF pressure line or dosing valve blocked
K4632 SCR system ERROR: DEF pressure stabilisation failure
K4633 SCR system ERROR: DEF pressure reduction failure
K4634 SCR system ERROR: DEF pressure build up failure
K4640 DEF tank temperature abnormal rate of change at heating cycle
K4641 DEF dosing valve overheat protection
K4642 SCR catalyst inlet gas temp sensor value implausible
K4643 SCR catalyst outlet gas temp sensor value implausible
K4644 Downstream NOx sensor value implausible
K4645 Downstream NOx sensor stability time exceeded
K4646 Upstream NOx sensor value implausible
K4647 Upstream NOx sensor stability time exceeded
K4648 Nox conversion implausible
K4649 Downstream NOx sensor supply voltage out of range
K4650 Upstream NOx sensor supply voltage out of range

A C D H K M P R S T U V W X Y

Ý
Top

Work Light Error Codes

M0010 Work Light Relay 1 open circuit
M0011 Work Light Relay 1 shorted to ground
M0012 Work Light Relay 1 ground not low
M0013 Work Light Relay 1 no coil power
M0020 Work Light Relay 2 open circuit
M0021 Work Light Relay 2 shorted to ground
M0022 Work Light Relay 2 ground not low
M0023 Work Light Relay 2 no coil power
M0030 Work Light Relay 3 open circuit
M0031 Work Light Relay 3 shorted to ground
M0032 Work Light Relay 3 ground not low
M0033 Work Light Relay 3 no coil power
M0040 Work Light Relay 4 open circuit
M0041 Work Light Relay 4 shorted to ground
M0042 Work Light Relay 4 ground not low
M0043 Work Light Relay 4 no coil power
M0050 Work Light Relay 5 open circuit
M0051 Work Light Relay 5 shorted to ground
M0052 Work Light Relay 5 ground not low
M0053 Work Light Relay 5 no coil power
M0060 Work Light Relay 6 open circuit
M0061 Work Light Relay 6 shorted to ground
M0062 Work Light Relay 6 ground not low
M0063 Work Light Relay 6 no coil power
M0070 Work Light Relay 7 open circuit
M0071 Work Light Relay 7 shorted to ground
M0072 Work Light Relay 7 ground not low
M0073 Work Light Relay 7 no coil power
M0080 Work Light Relay 8 open circuit
M0081 Work Light Relay 8 shorted to ground
M0082 Work Light Relay 8 ground not low
M0083 Work Light Relay 8 no coil power

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 11 of 23

M0403 Software fault

M0404 Software fault
M0405 Software fault

A C D H K M P R S T U V W X Y

Ý
Top

DECU Touch Screen

P0000 This fault code is for information only
P0001 CAN error: EMS stops communicating with the DECU
P0002 CAN error: ABS stops communicating with the DECU
P0003 CAN error: Engine ECU stops communicating with the DECU
P0004 CAN error: ECU1 stops communicating with the DECU
P0005 CAN error: EHR stops communicating with the DECU
P0006 CAN error: Gearbox ECU stops communicating with the DECU
P0007 DECU Service Master Settings Failed To Save
P0008 Trip Min / Max Log reset by the service laptop
P0009 Min / Max Log has been reset by the service laptop
P0010 Transmission Operating Characteristics reset by the service laptop
P0011 Engine Operating Characteristics reset by the service laptop
P0012 DECU calibration value reset on power up
P0013 DECU calibration value failed to save
P0014 Hand Throttle Idle Position Calibration Failed
P0015 Hand Throttle Maximum Speed Calibration Failed
P0016 Foot Throttle Idle Position Calibration Failed
P0017 Foot Throttle Maximum Speed Calibration Failed
P0018 Joystick Centre Position Calibration Failed
P0019 Joystick Right Position Calibration Failed
P0020 Joystick Left Position Calibration Failed
P0029 DECU ‘Front PTO’ Configuration failed to load
P0030 DECU ‘Rear PTO’ Configuration failed to load
P0031 DECU ‘Front PTO’ Configuration failed to save
P0032 DECU ‘Rear PTO’ Configuration failed to save
P0033 DECU ‘4WD’ Configuration failed to save
P0034 DECU ‘4WD’ Configuration failed to load
P0035 DECU ‘Area cutout’ Configuration failed to save
P0036 DECU ‘Area cutout’ Configuration failed to load
P0037 Steering Angle ‘Left’ Calibration Failed
P0038 Steering Angle ‘Right’ Calibration Failed
P0039 Rear PTO Calibration Failed
P0040 Rear PTO Calibration Passed
P0041 Front PTO Calibration Failed
P0042 Front PTO Calibration Passed
P0043 Joystick Calibration Value Failed To Save
P0044 Joystick Calibration Value Failed To Load
P0045 DECU User Settings Failed to Save
P0046 DECU User Settings Failed to Load
P0047 DECU Internal Temperature Sensor low
P0048 DECU Internal Temperature Sensor under range
P0049 DECU Internal Temperature Sensor high
P0050 DECU Internal Temperature Sensor over range
P0051 Hand Throttle 5 volt Sensor Supply low
P0052 Hand Throttle 5 volt Sensor Supply under range
P0053 Hand Throttle 5 volt Sensor Supply high
P0054 Hand Throttle 5 volt Sensor Supply over range

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 12 of 23

P0055 Should not occur

P0056 Should not occur
P0057 Should not occur
P0058 Should not occur
P0059 DECU detected Ignition Supply Voltage is Low
P0060 DECU detected Ignition Supply Voltage is Low
P0061 DECU detected Ignition Supply Voltage is High
P0062 DECU detected Ignition Supply Voltage is High
P0063 Steering Angle ‘Straight Ahead’ Calibration Failed
P0064 DECU ‘Spool Value’ Configuration Load Failed
P0065 DECU ‘Spool Configuration’ Failed To Save
P0066 DECU ‘Transmission Control’ Configuration Load Failed
P0067 DECU ‘Transmission Control’ Configuration Value Failed To Save
P0068 DECU engine preset configuration failed to load
P0069 DECU engine preset configuration failed to save
P0070 DECU lost CanBus communication with Work Lights
P0071 DECU BCA SS1 no CAN
P0072 Incomplete Power Down
P0073 DECU Differential lock value failed to save
P0074 DECU Differential lock configuration load failed
P0075 DECU Ignition Voltage Low
P0076 DECU and BCAG configuration mismatch.
P0080 GPS Steering Hydraulic Pressure Low Error
P0081 GPS Steering Hydraulic Pressure Sensor Open Circuit Error
P0082 GPS Steering Hydraulic Pressure High Error
P0083 GPS Steering Hydraulic Over Pressure Error
P0084 GPS Steering ESV solenoid High Side Driver supply error
P0085 GPS Steering ESV solenoid High Side Driver short circuit error
P0086 GPS Steering ESV solenoid High Side Driver open circuit error
P0087 GPS Steering ESV Solenoid High Side Driver Over Temperature Error
P0092 Handbrake on when moving.
P0130 Foot Throttle Signal Under Calibration
P0131 Foot Throttle Signal Under Range
P0132 Foot Throttle Signal Over Calibration
P0133 Foot Throttle Signal Over Range
P0150 Hand Throttle Signal Under Calibration
P0151 Hand Throttle Signal Under Range
P0152 Hand Throttle Signal Over Calibration
P0153 Hand Throttle Signal Over Range
P0170 Steering Angle Sensor Under Calibration
P0171 Steering Angle Sensor Under Range
P0172 Steering Angle Sensor Over Calibration
P0173 Steering Angle Sensor Over Range
P0180 Joystick Forwards / Backwards Under Calibration
P0181 Joystick Forward / Backwards Under Range
P0182 Joystick Forward / Backwards Over Calibration
P0183 Joystick Forward / Backwards Over Range
P0190 Joystick Left / Right Under Calibration
P0191 Joystick Left / Right Under Range
P0192 Joystick Left / Right Over Calibration
P0193 Joystick Left / Right Over Range
P0300 Foot Throttle Sensor Signal Plausibility Error
P0303 Engine Speed Signal Plausibility Error
P0304 Maximum vehicle speed occurred – information only
P0305 Maximum engine speed occurred – information only
P0306 Maximum vehicle voltage occurred – information only
P0307 Maximum Engine Coolant Temperature occurred – information only
P0308 Maximum Transmission temperature occurred – information only
P0309 DECU reached maximum internal temperature – information only

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 13 of 23

P0310 DECU internal temperature reached limit – information only

P0311 DECU LCD display shut down because the temperature was too hot
P0312 Hand Throttle signal Plausibility error
P0313 Engine speed received by the DECU out of range or not updated
P0315 Engine speed reduced due to very cold hydraulic oil temperature
P0320 Front PTO Cab Switch signal plausibility error
P0321 Rear PTO Cab Switch signal plausibility error
P0322 Control Panel Switch signals not received by DECU
P0335 VIN Number Invalid
P0336 Setup tool version invalid
P0340 The joystick position appears to be implausible.
P0341 Arm rest button implausible.
P0380 Power Boost Override Manually Enabled
P0385 Operator Present Implausibility
P0386 Secondary operator present input is out of range low
P0387 Secondary operator present input is out of range high
P0388 Secondary operator present input is out of normal range
P0395 DECU EHR43 Parameter set incorrect
P0400 6x4 Transmission: Direction Plausibility error
P0401 6x4 Transmission: failed to change Neutral within timeout
P0402 6x4 Transmission: failed to change gear within timeout
P0403 6x4 Transmission: failed to respond to gear request
P0404 6x4 Transmission: TECU gear is out of range
P0405 Transmission current gear is invalid
P0406 Transmission failed to change Range within the specified time
P0407 Transmission internal test did not complete with in required time.
P0410 Transmission Output Shaft Speed Sensor fault
P0411 Transmission Output Shaft speed invalid to available gears
P0415 Mismatch between the VIN number and DECU software
P0416 DECU Configuration Implausible
P0417 Gearbox Not Calibrated At Correct Temperature
P0420 12V Transmission sensor supply fault
P0421 Brake Pedal Signal plausibility fault detected by DECU
P0422 6X4 transmission not compatible with engine ID
P0423 6X4 transmission: Calibration mode entered unexpectedly
P0424 6X4 transmission software: DECU requested gear out of range
P0425 6X4 transmission software: DECU Reversal gear flag not available
P0426 6X4 transmission software: DECU Reversal gear flag not available
P0427 Transmission calibration successfully passed
P0428 Transmission calibration failed
P0429 The operator left the seat during the calibration sequence
P0430 Speed Limiter exceeded for more than 5 minutes continuously
P0431 The 2 brake pedal switches do not agree
P0432 The vehicle speed exceeds that valid for the current gear
P0433 The driver is allowing the vehicle to coast at too high a speed
P0434 Implausible gearbox shaft speeds
P0435 Operator Controls have not entered Neutral at start-up
P0436 Vehicle Speed implausible to selected gear
P0438 Insufficient Vehicle Deceleration During a Reversal
P0439 Gearbox Speed Signal indicates implausible or erratic vehicle speeds
P0440 DECU Touch Screen Calibration fault
P0441 DECU CanBus message frozen
P0442 No operator when vehicle moving
P0443 DECU ‘Apply Parkbrake’ Warning active
P0444 Transmission timed out when DECU ‘Apply Parkbrake’ Warning active
P0445 The absolute gearbox energy count limit has been exceeded during reversals
P0448 Excessive Slip Energy Limit when Xtradrive NOT active
P0454 DECU BCA Hill hold driver not present

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 14 of 23

P0455 DECU Resume button fault

P0456 DECU Joystick black button fault
P0457 DECU Joystick white button fault
P0458 DECU Joystick trigger button fault
P0460 BCA Front brakes, air pressure fault
P0461 BCA Rear brakes, air pressure fault
P0462 BCA accelerometer fault
The joystick has been held in the forward or backward positions to an
P0463
extended period.
P0468 Energy slip calculation threshold exceeded at ignition on
P0470 Front PTO speed implausible to engine speed
P0471 Rear PTO speed implausible to engine speed
P0472 DECU to Engine CanBUS message EEC1 anomoly.
P0475 Range Gears Synchronizer: protection warning
P0478 Forced Change Down Anomaly During A Reversal
P0480 Engine stalled – ‘Power Down’ DECU before restarting
P0484 Clutch System plausibility error
P0485 Transmission Master Clutch Slipping as Clutch Pedal not fully returned
P0486 Transmission Master Clutch Slipping
P0487 Xtradrive Excessive Slip Energy Warning
P0488 Xtradrive Excessive Slip Energy Limit
P0489 Xtradrive Excessive Slip Time Warning
P0490 Transmission Oil filter blocked
P0495 Transmission Oil Temperature has not changed
P0496 Transmission Bulk Oil Temperature above normal operating level
P0497 Master Clutch Oil Temperature above normal operating level
Transmission Oil temperature difference above normal operating level when
P0498
the engine is running
Transmission Oil Temperature difference above normal operating level at
P0499
Engine start up
P0510 Transmission configuration error.
P0990 DECU software fault
P0991 DECU software fault
P0992 DECU software fault
P0993 DECU software fault
P0994 DECU software fault
P0995 DECU software fault
P0996 DECU software fault
P0997 DECU software fault
P0998 DECU software fault
P0999 DECU software fault

A C D H K M P R S T U V W X Y

Ý
Top

Rear Hitch
R0101 Rear Hitch Solenoid Valve: Raise Fault
R0102 Rear Hitch Solenoid Valve: Lower Fault
R0103 Rear Hitch Raise/Lower Solenoid Valve circuit shorted
R0104 Rear Linkage Raise Over-ride Control fault
R0105 Rear Linkage Lower Over-ride Control fault
R0106 Rear Hitch Draft Control (EHR) supply fault
R0107 Rear Hitch Draft Control (EHR) Battery Voltage Too High
R0108 Rear Hitch Main Control Switch fault
R0202 Rear Hitch Position Sensor Fault
R0203 Rear Hitch Control Working Depth Potentiometer Fault

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 15 of 23

R0204 Rear Hitch Control Maximum Lift Height Potentiometer Fault

R0205 Rear Hitch Draft Control (EHR) CanBus Fault
R0206 Rear Hitch Draft Control (EHR): external sensor fault
Rear Hitch Draft Control (EHR) lost CanBus communication with
R0207
DECU
R0301 Rear Hitch Right Draft Pin Fault
R0302 Rear Hitch Left Draft Pin Fault
R0303 Rear Hitch Draft Control (EHR) Battery Voltage Too Low
R0304 Rear Hitch Control: Working Depth Potentiometer Fault
R0306 Rear Hitch Controls: Draft Mixture Potentiometer Fault
R0307 Rear Hitch failed to move to required position
R0401 Radar Speed Signal Fault detected by EHR Draft Control
EHR detected a fault with the Transmission Crownwheel Speed
R0402
signal
R0407 Rear hitch potentiometer requires calibration
R0500 Rear Hitch Working Depth Control: Signal Plausibility fault
R0501 Rear Hitch Draft Mixture Control: Signal Plausibility fault
Rear Hitch Maximum Raise Height Controls: Signal Plausibility
R0502 Fault
R0503 Rear Hitch Drop Rate: Signal Plausibility Fault
R0504 Rear Hitch Draft Mixture Potentiometer: Signal 1 Open or Shorted
Rear Hitch Maximum Raise Height Controls: Signal 1 Open or
R0505 Shorted
R0506 Rear Hitch Drop Rate Controls: Signal 1 Open or Shorted
R0507 Rear Hitch Draft Mixture Controls: Signal 2 Open or shorted
Rear Hitch Maximum Raise Height Controls: Signal 2 Open or
R0508 Shorted
R0509 Rear Hitch Drop Rate Controls: Signal 2 Open or Shorted
R0510 Rear Hitch Working Depth Control: Signal 1 Open or Shorted
R0511 Rear Hitch Working Depth Control: Signal 2 Open or Shorted
R0512 Rear Linkage Main Raise/Lower Switch: Signal 1 Open or Shorted
R0513 Rear Linkage Main Raise/Lower Switch : Signal 2 Open or Shorted
R0514 Rear Linkage Main Raise/Lower Switch : Signal 3 Open or Shorted

A C D H K M P R S T U V W X Y

Ý
Top

Suspension
S0001 Rear Left Suspension Ride Height Potentiometer over range
S0002 Rear Left Suspension Ride Height Potentiometer under range
S0003 Rear Right Suspension Ride Height Potentiometer over range
S0004 Rear Right Suspension Ride Height Potentiometer under range
S0007 Rear Left Suspension value less than the allowable limit for calibration
S0008 Rear Left Suspension value greater than the allowable limit for calibration
S0009 Rear Right Suspension signal less than the allowable limit for calibration
S0010 Rear Right Suspension signal greater than the allowable limit for calibration
S0011 Rear Suspension calibration required
S0020 Rear Left Suspension Raise Solenoid valve: open or shorted to supply
S0021 Rear Left Suspension Raise Solenoid valve: short circuit
S0022 ECU1 Internal fault: Rear Left Suspension Driver fault
S0030 Rear Left Suspension Lower Solenoid Valve: open or shorted to supply
S0031 Rear Left Suspension Lower Solenoid valve: short circuit
S0032 ECU1 Internal fault: Rear Left Suspension Driver fault
S0040 Rear Right Suspension Raise Solenoid Valve: open or shorted to supply
S0041 Rear Right Suspension Raise Solenoid valve: short circuit
S0042 ECU1 Internal fault: Rear Right Suspension Driver fault
S0050 Rear Right Suspension Lower Solenoid Valve: open or shorted to supply

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 16 of 23

S0051 Rear Right Suspension Lower Solenoid valve: short circuit

S0052 ECU1 Internal fault: Rear Right Suspension Driver fault
S0101 Front Suspension Ride Height Potentiometer over range
S0102 Front Suspension Ride Height Potentiometer under range
S0103 FCC Electronics front suspension errors
S0104 FCC Electronics front suspension errors
S0107 Front Suspension signal less than the allowable limit for calibration
S0108 Front Suspension signal greater than the allowable limit for calibration
S0109 FCC Electronics front suspension errors
S0110 FCC Electronics front suspension errors
S0111 FCC Electronics front suspension errors
S0120 Front Suspension Raise Solenoid valve: open circuit or shorted to supply
S0121 Front Suspension Raise Solenoid valve: short circuit
S0122 ECU1 Internal fault: Front Suspension Driver fault
S0130 Front Suspension Lower Solenoid valve: open or shorted to supply
S0131 Front Suspension Lower Solenoid valve: short circuit
S0132 ECU1 Internal fault: Front Suspension Driver fault
S0140 FCC Electronics front suspension errors
S0141 FCC Electronics front suspension errors
S0142 FCC Electronics front suspension errors
S0150 FCC Electronics front suspension errors
S0151 FCC Electronics front suspension errors
S0152 FCC Electronics front suspension errors

A C D H K M P R S T U V W X Y

Ý
Top

Gearbox 6x4
T1000 Transmission Output Shaft Speed Sensor: under range
T1001 Transmission Output Shaft Speed Sensor: signal over-range
T1010 Transmission Intermediate shaft speed sensor: signal under range
T1011 Transmission Intermediate shaft speed sensor over-range
T1020 Transmission ‘Rail 1’ Range Position Sensor: signal under range
T1021 Transmission ‘Rail 1’ Range Position Sensor: over-range
T1022 Transmission ‘Rail 1’ Range Position Sensor: signal not plausible
T1030 Transmission ‘Rail 2’ Range Position Sensor: signal under range
T1031 Transmission ‘Rail 2’ Range Position Sensor: signal over-range
T1032 Transmission ‘Rail 2’ Range Position Sensor: signal not plausible
T1040 Transmission Oil Temperature Sensor: signal under range
T1041 Transmission Bulk Oil Temperature sensor: signal over-range
T1042 Transmission Bulk Oil Temperature sensor: signal has not changed in 30
minutes
T1044 Transmission Bulk Oil Temperature exceeded limit
T1050 Master Clutch Temperature Sensor: signal under range
T1051 Master Clutch Oil Temperature Sensor: signal over-range
T1052 Master Clutch Oil Temperature Sensor: signal value has not changed
T1053 Transmission Oil temperature difference too high.
T1054 Master Clutch Oil Temperature exceeded limit
T1060 Clutch Pedal Position Sensor: signal under range
T1061 Clutch Pedal Position Sensor: signal over-range
T1062 Powershift Relay not disengaged when Clutch Pedal is fully depressed
T1070 Clutch Activation Switch not detected when Clutch Pedal at 0%
T1071 Clutch Activation Switch ‘On’ when Clutch Pedal above 60%
T1080 Transmission Oil Pressure Low

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 17 of 23

T1200 Powershift Solenoid Valve ‘A’: short-circuit

T1201 Powershift Solenoid Valve ‘A’: open-circuit
T1210 Powershift Solenoid Valve ‘B’: short-circuit
T1211 Powershift Solenoid Valve ‘B’: open-circuit
T1220 Powershift Solenoid Valve ‘C’: short-circuit
T1221 Powershift Solenoid Valve ‘C’: open-circuit
T1230 Powershift Solenoid Valve ‘D’: short-circuit
T1231 Powershift Solenoid Valve ‘D’: open-circuit
T1240 Powershift Solenoid Valve ‘E’: short-circuit
T1241 Powershift Solenoid Valve ‘E’: open-circuit
T1250 Powershift Solenoid Valve ‘Reverse’: short-circuit
T1251 Powershift Solenoid Valve ‘Reverse’: open-circuit
T1260 Master Clutch Solenoid Valve: short-circuit
T1261 Master Clutch Solenoid Valve: open-circuit
T1270 Master Clutch Lubrication Valve: short-circuit
T1271 Master Clutch Lubrication Valve: open circuit
T1280 Master Clutch ‘Brake’ Solenoid Valve: short-circuit
T1281 Master Clutch ‘Brake’ Solenoid valve: open-circuit
T1290 Range Solenoid ‘B’: short-circuit
T1291 Range Solenoid ‘B’: open-circuit
T1300 Range Solenoid ‘A’: short-circuit
T1301 Range Solenoid ‘A’: open circuit
T1310 Range Solenoid ‘D’: short-circuit
T1311 Range Solenoid ‘D’: Open-circuit
T1340 Range Solenoid ‘C’: short-circuit
T1341 Range Solenoid ‘C’: open-circuit
T1350 Transmission Buzzer Output Open Circuit
T1351 Transmission Buzzer Output Short Circuit
T1400 Transmission Range Change failed
T1401 Invalid CanBus message received by TECU
T1402 Invalid CanBus message received by TECU
T1403 Invalid CanBus message received by TECU
T1404 Invalid CanBus message received by TECU
T1405 Invalid CanBus message received by TECU
T1406 Transmission ECU Control software fault
T1407 Transmission ECU Control software fault
T1408 Transmission ECU Control software fault
T1409 Transmission ECU Control software fault
T1410 Transmission ECU Control software fault
T1411 Transmission ECU Control software fault
T1412 Transmission ECU Control software fault
T1413 Transmission ECU Control software fault
T1414 Transmission ECU Control software fault
T1415 Gearbox Speeds signals from the Intermediate and Output shaft speeds are
implausible
T1416 Intermediate Shaft Speed and engine speed not plausible
T1417 Transmission Speed Sensor fault during Start-up check
T1418 Transmission Master Clutch has been slipping excessively
T1419 Transmission ECU Software fault
T1420 Transmission ECU Software fault
T1421 TECU detected engine RPM exceeds 3750RPM
T1422 TECU detected Engine RPM has not changed in 2 minutes
T1423 TECU detected Engine RPM message has not been received in 2 seconds
T1424 TECU detected Engine torque has exceed 125%
T1425 TECU detected Engine torque has not changed in 2 minutes
T1426 TECU detected Engine torque message has not been received in 2 seconds
T1427 TECU detected DECU communication had not been received in 2 seconds
T1450 Transmission fault detected – for DECU information
T1451 Transmission fault detected – for DECU information

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 18 of 23

T1452 Transmission ECU Software fault (Invalid gear request)

T1453 Invalid value set in for Double de-clutching message
T1454 During double de-clutching the range box rails took too long to get to
Neutral
T1455 Hold Stationary Requested
T1456 Tractor Moved When Hold Stationary Selected
T1457 Output shaft speed sensors have speed difference greater than 10%
T1458 Sensed vehicle direction implausible vs current gear
T1459 Hold stationary requested when moving
T1500 Transmission Range Calibration Fault: Clutch Pedal ‘Down’ value too low
T1501 Transmission Range Calibration Fault: Clutch Pedal ‘Down’ value too high
T1502 Transmission Range Calibration Fault: Clutch Pedal ‘Up’ value too low
T1503 Transmission Range Calibration Fault: Clutch Pedal ‘Up’ value too high
T1510 Transmission Range Calibration Fault: ‘Rail 1’ (point 1) too low
T1511 Transmission Range Calibration Fault: ‘Rail 1’ (point 1) too high
T1512 Transmission Range Calibration Fault: ‘Rail 1’ (point 2) too low
T1513 Transmission Range Calibration Fault: ‘Rail 1’ (point 2) too high
T1520 Transmission Range Calibration Fault: ‘Rail 2’ (point 1) too low
T1521 Transmission Range Calibration Fault: ‘Rail 2’ (point 1) too high
T1522 Transmission Range Calibration Fault: ‘Rail 2’ (point 2) too low
T1523 Transmission Range Calibration Fault: ‘Rail 2’ (point 2) too high
T1530 Transmission Clutch Calibration Fault: Master Clutch bite point current too
low
T1531 Transmission Clutch Calibration Fault: Master Clutch bite point current too
high
T1532 Transmission Clutch Calibration Fault: Master Clutch time too low
T1533 Transmission Clutch Calibration Fault: Master Clutch time too high
T1534 Transmission Calibration Fault: Powershift Valve ‘A’ bite point too low
T1535 Transmission Calibration Fault: Powershift Valve ‘A’ bite point too high
T1536 Transmission Calibration Fault: Powershift Valve ‘B’ bite point too low
T1537 Transmission Calibration Fault: Powershift Valve ‘B’ bite point too high
T1538 Transmission Calibration Fault: Powershift Valve ‘R’ bite point too low
T1539 Transmission Calibration Fault: Powershift Valve ‘R’ bite point too high
T1540 Transmission Calibration Fault: Powershift Valve ‘C’ bite point too low
T1541 Transmission Calibration Fault: Powershift Valve ‘C’ bite point too high
T1542 Transmission Calibration Fault: Powershift Valve ‘D’ bite point too low
T1543 Transmission Calibration Fault: Powershift Valve ‘D' bite point too high
T1544 Transmission Calibration Fault: Powershift Valve ‘E’ bite point too low
T1545 Transmission Calibration Fault: Powershift Valve ‘E’ bite point too high
T1550 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘A’
T1551 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘B’ bite point
T1552 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘R’ bite point
T1553 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘C’ bite point
T1554 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘D’ bite point
T1555 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘E’ bite point
T1556 Transmission calibration Fault: failed to achieve high range for PS calibration
T1560 ECU has no calibration values for transmission
T1570 Transmission Calibration failed: Handbrake is disengaged
T1571 Transmission Calibration failed: Output Shaft Speed is not zero
T1572 Transmission Calibration failed: engine RPM outside calibration range
T1573 Transmission Calibration occurred when oil temperature too low
T1574 Transmission Calibration occurred when oil temperature too high
T1575 Transmission Calibration Fault: change in engine torque not detected for
Master Clutch
T1576 Transmission Calibration Fault: change in engine torque not detected for

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 19 of 23

Master Clutch
T1580 Transmission Calibration Fault: Speed Plausibility error for Powershift
Reverse Gear
T1581 Transmission Calibration Fault: Speed Plausibility error for Powershift Speed
1
T1582 Transmission Calibration Fault: Speed Plausibility error for Powershift Speed
2
T1583 Transmission Calibration Fault: Speed Plausibility error for Powershift Speed
3
T1584 Transmission Calibration Fault: Speed Plausibility error for Powershift Speed
4
T1585 Transmission Calibration Fault: Speed Plausibility error for Powershift Speed
5
T1586 Transmission Calibration Fault: Speed Plausibility error for Powershift Speed
6
T1590 Transmission Calibration Fault: Powershift Clutch ‘A’ calibration time too
low
T1591 Transmission Calibration Fault: Powershift Clutch ‘A’ calibration time too
high
T1592 Transmission Calibration Fault: Powershift Clutch ‘B’ calibration time too
low
T1593 Transmission Calibration Fault: Powershift Clutch ‘B’ calibration time too
high
T1596 Transmission Calibration Fault: Powershift Clutch ‘C’ calibration time too
low
T1597 Transmission Calibration Fault: Powershift Clutch ‘C’ calibration time too
high
T1598 Transmission Calibration Fault: Powershift Clutch ‘D’ calibration time too
low
T1599 Transmission Calibration Fault: Powershift Clutch ‘D’ calibration time too
high
T1600 Transmission Calibration Fault: Powershift Clutch ‘E’ calibration time too low
T1601 Transmission Calibration Fault: Powershift Clutch ‘E’ calibration time too
high
T1602 Clutch Activation Switch ‘On’ when Clutch Position percentage too low
T1603 Clutch Activation Switch ‘On’ when Clutch Position signal voltage too high
T1610 Transmission Calibration Fault: Powershift Clutch ‘R’ calibration time too
low
T1611 Transmission Calibration Fault: Powershift Clutch ‘R’ calibration time too
high
T1650 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘A’ cal time
T1651 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘B’ cal time
T1652 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘R’ cal time
T1653 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘C’ cal time
T1654 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘D’ cal time
T1655 Transmission Calibration Fault: change in engine torque not detected for
Powershift Valve ‘E’ cal time

A C D H K M P R S T U V W X Y

Ý
Top

Front Hitch Slice

U0000 Valve block CanBus Communication fault - Front Hitch Slice
U0001 Valve block CanBus Communication fault – Front Hitch Slice
U0002 Implausible CanBus Data Received Message - Front Hitch Slice
U0003 Implausible CanBus receive Message – Front Hitch Slice

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 20 of 23

U0004 Front Hitch Slice internal fault

U0005 EEPROM Inconsistent - Front Hitch Slice
No faults but valve has switched off for >4 seconds - Front Hitch
U0006
Slice
U0007 Valve Slice Supply Voltage < 11 volts: Front Hitch Slice
U0008 Valve Slice Supply Voltage > 16 volts – Front Hitch Slice
U0010 Excessive Internal Spool Movement - Front Hitch Slice
U0011 Internal Spool Float Position Not Reached - Front Hitch Slice
U0012 Spool Valve Operated Manually - Front Hitch Slice
U0013 Supply Voltage < 8 Volts - Front Hitch Slice
U0014 Supply > 36 but < 45 volts - Front Hitch Slice
U0015 High Over Voltage Supply > 45 volts - Front Hitch Slice
U0016 Output Stage Fault - Front Hitch Slice
U0017 Valve block internal Position transducer fault – Front Hitch Slice
Spool Valve Cannot return To The Neutral Position – Front Hitch
U0018
Slice
U0019 Spool Not In Neutral When Powered Up – Front Hitch Slice
U0020 Program Memory Error – Front Hitch Slice
U0021 Spool valve Off Line: Front Hitch Slice
U0066 Front Hitch Position Sensor: signal over-range
U0067 Front Hitch Position Sensor: signal under-range
U0068 Front Hitch Position Sensor input open circuit
U0071 Spool Valve very high temperature – Front Hitch Slice
U0073 Front Hitch calibration required
U0124 Front Hitch Controls message from ACE not received by ECU1
U0201 Spool movement too short – Front Hitch Slice
U0500 Front Hitch Working Depth Control: Signal Plausibility Fault
U0502 Front Hitch Maximum Raise Height Controls: Signal Plausibility Fault
U0503 Front hitch Drop Rate : signal plausibility fault
Front Hitch Maximum Raise Height Controls: Signal 1 Open or
U0505 Shorted
U0506 Front Hitch Drop Rate Controls: Signal 1 Open or Shorted
Front Hitch Maximum Raise Height Controls: Signal 2 Open or
U0508 Shorted
U0509 Front Hitch Drop Rate Controls: Signal 2 Open or Shorted
U0510 Front Hitch Working Depth Control: Signal 1 Open or Shorted
U0511 Front Hitch Working Depth Control: Signal 2 Open or Shorted
Front Hitch Main Raise/Lower Switch: Signal 1 Open circuit or
U0512 Shorted
Front Hitch Main Raise/Lower Switch : Signal 2 Open circuit or
U0513 Shorted
U0514 Front Hitch Main Raise/Lower Switch : Signal 3 Open or Shorted

A C D H K M P R S T U V W X Y

Ý
Top

Green Slice
V0000 Valve block CanBus Communication fault - Green Slice
V0001 Valve block CanBus Communication fault – Green Slice
V0002 Implausible CanBus Data Received Message - Green Slice
V0003 Implausible CanBus Data Received Message – Green Slice
V0004 Potentiometer / PWM Fault - Green Slice
V0005 EEPROM Inconsistent - Green Slice
V0006 No faults but valve has switched off for >4 seconds - Green Slice
V0007 Valve Slice Supply Voltage < 11 volts: Green Hitch Slice
V0008 Valve Slice Supply Voltage > 16 volts - Green Slice
V0010 Excessive Internal Spool Movement - Green Slice

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 21 of 23

V0011 Internal Spool Float Position Not Reached - Green Slice

V0012 Spool Valve Operated Manually - Green Slice
V0013 Supply Voltage < 8 Volts - Green Slice
V0014 Supply > 36 but < 45 volts - Green Slice
V0015 High Over Voltage Supply > 45 volts - Green Slice
V0016 Output Stage Fault - Green Slice
V0017 Valve block internal Position transducer fault – Green Slice
V0018 Spool Valve Cannot return To The Neutral Position – Green Slice
V0019 Spool Not In Neutral When Powered Up – Green Slice
V0020 Program Memory Error – Green Slice
V0021 Spool valve Off Line: Green Slice
V0050 Main lever electrical input too low – Green slice
V0051 Main lever electrical input too high – Green slice
V0054 Flow or duration control driver open circuit -Green slice
V0055 Flow or duration control too low - Green slice
V0056 Flow or duration control too high - Green slice
V0070 Implausible main control lever position – Green Slice
V0071 Spool valve very high temperature – Green Slice
V0100 Green Slice Spool Lever : Signal Plausibility Fault
V0101 Green Slice Spool Lever : Signal Fault
V0102 Green Slice Spool Lever : Signal Fault
V0124 Green Slice Controls message from ACE not received by ECU1
V0201 Spool Movement Too short - Green Slice

A C D H K M P R S T U V W X Y

Ý
Top

Blue Slice
W0000 Valve block CanBus Communication fault - Blue Slice
W0001 Valve block CanBus Communication fault – Blue Slice
W0002 Implausible CanBus Data Received Message - Blue Slice
W0003 Implausible CanBus Data Received Message - Blue Slice
W0004 Potentiometer / PWM Fault - Blue Slice
W0005 EEPROM Inconsistent - Blue Slice
W0006 No faults but valve has switched off for >4 seconds - Blue Slice
W0007 Valve Slice Supply Voltage < 11 volts: Blue Slice
W0008 Valve Slice Supply Voltage > 16 volts - Blue Slice
W0010 Excessive Internal Spool Movement - Blue Slice
W0011 Internal Spool Float Position Not Reached - Blue Slice
W0012 Spool Valve Operated Manually - Blue Slice
W0013 Supply Voltage < 8 Volts - Blue Slice
W0014 Supply > 36 but < 45 volts - Blue Slice
W0015 High Over Voltage Supply > 45 volts - Blue Slice
W0016 Output Stage Fault - Blue Slice
W0017 Valve block internal Position transducer fault – Blue Slice
W0018 Spool Valve Cannot return To The Neutral Position –Blue Slice
W0019 Spool Not In Neutral When Powered Up – Blue Slice
W0020 Program Memory Error – Blue Slice
W0021 Spool valve Off Line: Blue Slice
W0050 Main lever electrical input too low – Blue slice
W0051 Main lever electrical input too high – Blue slice
W0054 Flow or duration control driver open circuit - Blue slice
W0055 Flow or duration control too low – Blue slice
W0056 Flow or duration control too high – Blue slice
W0070 Implausible main control lever position – Blue Slice

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 22 of 23

W0071 Spool valve very high temperature – Blue Slice

W0100 Blue Slice Spool Lever : Signal Plausibility Fault
W0101 Blue Slice Spool Lever : Signal Fault
W0102 Blue Slice Spool Lever : Signal Fault
W0124 Blue Slice Controls message from ACE not received by ECU1
W0201 Spool movement too short – Blue Slic

A C D H K M P R S T U V W X Y

Ý
Top

Brown Slice
X0000 Valve block CanBus Communication fault - Brown Slice
X0001 Valve block CanBus Communication fault – Brown Slice
X0002 Implausible CanBus Data Received Message - Brown Slice
X0003 Implausible CanBus Data Received Message - Brown Slice
X0004 Potentiometer / PWM Fault - Brown Slice
X0005 EEPROM Inconsistent - Brown Slice
X0006 No faults but valve has switched off for >4 seconds - Brown Slice
X0007 Valve Slice Supply Voltage < 11 volts: Brown Slice
X0008 Valve Slice Supply Voltage > 16 volts - Brown Slice
X0010 Excessive Internal Spool Movement - Brown Slice
X0011 Internal Spool Float Position Not Reached - Brown Slice
X0012 Spool Valve Operated Manually - Brown Slice
X0013 Supply Voltage < 8 Volts - Brown Slice
X0014 Supply > 36 but < 45 volts - Brown Slice
X0015 High Over Voltage Supply > 45 volts - Brown Slice
X0016 Output Stage Fault - Brown Slice
X0017 Valve block internal Position transducer fault – Brown Slice
X0018 Spool Valve Cannot return To The Neutral Position – Brown Slice
X0019 Spool Not In Neutral When Powered Up – Brown Slice
X0020 Program Memory Error – Brown Slice
X0021 Spool valve Off Line: Brown Slice
X0050 Main lever electrical input too low – Brown slice
X0051 Main lever electrical input too high – Brown slice
X0054 Flow or duration control driver open circuit - Brown slice
X0055 Flow or duration control too low - Brown slice
X0056 Flow or duration control too high - Brown slice
X0059 Lever kick-out solenoid high side driver output disconnected Slice 3
X0070 Implausible main control lever position – Brown Slice
X0071 Spool valve very high temperature – Brown Slice
X0100 Brown Slice Spool Lever : Signal Plausibility Fault
X0101 Brown Slice Spool Lever : Signal Fault
X0102 Brown Slice Spool Lever : Signal Fault
X0124 Green Slice Controls message from ACE not received by ECU1
X0201 Spool movement too short – Brown Slic

A C D H K M P R S T U V W X Y

Ý
Top

Grey Slice

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024
3000 Series 3 Error Code List Page 23 of 23

Y0000 Valveblock CanBus Communication fault - Grey Slice

Y0001 Valveblock CanBus Communication fault – Grey Slice
Y0002 Implausible CanBus Data Received Message - Grey Slice
Y0003 Implausible CanBus Data Received Message – Grey Slice
Y0004 Potentiometer / PWM Fault - Grey Slice
Y0005 EEPROM Inconsistent - Grey Slice
Y0006 No faults but valve has switched off for >4 seconds - Grey Slice
Y0007 Valve Slice Supply Voltage < 11 volts: Grey Slice
Y0008 Valve Slice Supply Voltage > 16 volts - Grey Slice
Y0010 Excessive Internal Spool Movement - Grey Slice
Y0011 Float Position Not Reached - Grey Slice
Y0012 Spool Valve Operated Manually - Grey Slice
Y0013 Supply Voltage < 8 Volts - Grey Slice
Y0014 Supply > 36 but < 45 volts - Grey Slice
Y0015 High Over Voltage Supply > 45 volts - Grey Slice
Y0016 Output Stage Fault - Grey Slice
Y0017 Valveblock internal Position transducer fault – Grey Slice
Y0018 Spool Valve Cannot return To The Neutral Position – Grey Slice
Y0019 Spool Not In Neutral When Powered Up – Grey Slice
Y0020 Program Memory Error – Grey Slice
Y0021 Spool valve Off Line – Grey Slice
Y0050 Main lever electrical input too low – Grey slice
Y0051 Main lever electrical input too high – Grey slice
Y0054 Flow or duration control driver open circuit -Grey slice
Y0055 Flow or duration control too low - Grey slice
Y0056 Flow or duration control too high - Grey slice
Y0070 Implausible main control lever position – Grey Slice
Y0071 Spool valve very high temperature – Grey Slice
Y0100 Grey Slice Spool Lever : Signal Plausibility Fault
Y0101 Grey Slice Spool Lever : Signal Fault
Y0102 Grey Slice Spool Lever : Signal Fault
Y0124 Grey Slice Controls message from ACE not received by ECU1
Y0201 Spool movement too short – Grey Slice

A C D H K M P R S T U V W X Y

Ý
Top

mk:@MSITStore:C:\JCB_Servicemaster_2\SM4Tools\Help\LP3000s3Help.chm::/eng/... 6/12/2024