Technical Data for EPC and EPCD-Series OEM Pressure Controllers

1–500 PSI single-valve and dual-valve controllers for absolute and gauge pressure
+1 (888) 290-6060
Standard specifications shown. Consult Alicat for available options.
alicat.com/epc • alicat.com/epcd

SENSOR AND CONTROL PERFORMANCE

Absolute: 15–500 PSIA
Available Pressure Ranges
Gauge: 1–500 PSIG
Accuracy at calibration conditions1 ±0.125% of full scale
Repeatability (2σ)1 ±0.08% of full scale
Steady State Control Range 0.01–100% of full scale
Typical Control Response Time As fast as 30 ms, flow rate and valve size dependent, user adjustable
Valve Function Normally closed
Zero shift: 0.02% full scale per °C from tare temperature2
Temperature Sensitivity
Span shift: 0.02% full scale per °C from calibration temperature
Operating Temperature Range −10–60°C
Sensor Response Time <1 ms
Typical Indication Response Time <10 ms
Typical Warm-Up Time <1 s
1 Stated accuracy is after tare under equilibrium conditions; includes repeatability and linearity.
2 Tare is not available on absolute pressure devices.

MECHANICAL
≤100 PSI models: 3× full scale range
Sensor Burst Pressure
>100 PSI models: 1.5× full scale range
Gas Compatibility Compatible with dry, non-corrosive gases
Mounting Attitude Sensitivity None
2× through holes accepting #4 cap head screws and
Mounting Options
2× 4-40 UNC tapped holes with a depth of 0.200″ [5.08 mm]
Relative Humidity Range 0–95%, non-condensing
≤100 PSI models: 300 and 430FR stainless steel, hard-anodized aluminum, FKM, alumina ceramic, glass,
gold, heat-cured epoxy, heat-cured silicone rubber, brass, nickel plated brass 360 HT, polyamide, silicon
Wetted Materials
>100 PSI models: 316L, 300 and 430FR stainless steel, hard-anodized
aluminum, FKM, brass, nickel plated brass 360 HT
EPC and EPCD inlet and outlet: 1/8″ NPT female
Process Connections
EPCD exhaust: M5×0.8 female
Ingress Protection None (default), IP66/67 (optional)

COMMUNICATIONS AND ELECTRICAL

Analog I/O Options 0–5 Vdc, 1–5 Vdc, 0–10 Vdc, 4–20 mA
RS-232 Serial and Modbus RTU (default)
Digital I/O Options
RS-485 Serial and Modbus RTU (optional)
Standard models: 6-pin Molex® Micro-Fit®
Electrical Connection
IP66/67 models: 6-pin M8 connector
24 Vdc, 290 mA (default)
Power Requirements
12 Vdc, 290 mA (optional)
Analog Data Update Rate 1 kHz
Analog Signal Accuracy ±0.1% of full scale additional uncertainty
Digital Data Update Rate 60 Hz at 19200 baud

DOC-SPECS-EPC-EPCD · REV 8, 17 Jan 2022 1 ⁄ 4

 Technical Data for EPC and EPCD-Series OEM Pressure Controllers
1–500 PSI single-valve and dual-valve controllers for absolute and gauge pressure
+1 (888) 290-6060
Standard specifications shown. Consult Alicat for available options.
alicat.com/epc • alicat.com/epcd

EPC-Series

2× ⌀ #4 cap head
F

D E

6-pin
Micro-Fit

6-Pin Micro-Fit Pinout

1 Power in
2 Analog output
H 3 Ground
4 RS-232TX or RS-485(+)
Valve 5 RS-232RX or RS-485(−)
6 Analog setpoint input

A A
IN OUT

B W B
E
1⁄8″ NPT 1⁄8″ NPT
Inlet Port Outlet Port

F
2× 4-40 UNC ↧ 0.200″ [5.08 mm]

DIMENSIONS3 WEIGHT4
Model Height Width Depth A B E F G
EPC (all ranges), 3.041 in 2.000 in 1.322 in 0.375 in 0.650 in 0.115 in 1.035 in 1.885 in 6.2 oz
EPCD (≤100 PSI) 77.24 mm 50.80 mm 33.58 mm 9.53 mm 16.51 mm 2.92 mm 26.29 mm 47.88 mm 177.0 g
3 Port type, port locations, and other body dimensions may be customized. Contact Alicat for more information.
4 Maxmium product weights shown. Total device weight may vary depending on actual model configuration. Contact Alicat for more information.

DOC-SPECS-EPC-EPCD · REV 8, 17 Jan 2022 2 ⁄ 4

 Technical Data for EPC and EPCD-Series OEM Pressure Controllers
1–500 PSI single-valve and dual-valve controllers for absolute and gauge pressure
+1 (888) 290-6060
Standard specifications shown. Consult Alicat for available options.
alicat.com/epc • alicat.com/epcd

EPCD-Series
2× ⌀ #4 cap head F

E G
D

6-pin
Micro-Fit

Valves
6-Pin Micro-Fit Pinout
1 Power in
2 Analog output
H 3 Ground
4 RS-232TX or RS-485(+)
5 RS-232RX or RS-485(−)
6 Analog setpoint input

A A A
IN EXH OUT

B C B
1⁄8″ NPT M5×0.8 1⁄8″ NPT
Inlet Port Exhaust Port Outlet Port

F
2× 4-40 UNC ↧ 0.200″ [5.08 mm]

DIMENSIONS3 WEIGHT4
Model Height Width Depth A B C E F G
3.041 in 2.625 in 1.322 in 0.375 in 0.650 in 2.101 in 0.115 in 1.035 in 2.510 in 13.4 oz
EPCD (>100 PSI)
77.24 mm 66.68 mm 33.58 mm 9.53 mm 16.51 mm 53.37 mm 2.92 mm 26.29 mm 63.75 mm 377.0 g
3 Port type, port locations, and other body dimensions may be customized. Contact Alicat for more information.
4 Maxmium product weights shown. Total device weight may vary depending on actual model configuration. Contact Alicat for more information.

DOC-SPECS-EPC-EPCD · REV 8, 17 Jan 2022 3 ⁄ 4

 Technical Data for EPC and EPCD-Series OEM Pressure Controllers
1–500 PSI single-valve and dual-valve controllers for absolute and gauge pressure
+1 (888) 290-6060
Standard specifications shown. Consult Alicat for available options.
alicat.com/epc • alicat.com/epcd

EPC & EPCD

IP66/67
D

M8
W

M8 Pinout
1 Power in
2 Analog output
3 Ground
4 RS-232TX or RS-485(+)
H 5 RS-232RX or RS-485(−)
6 Analog setpoint input

A A A
IN
B C B
M5×0.8 Exhaust Port
(EPCD models only) 1⁄8″ NPT
1⁄8″ NPT G Outlet Port
Inlet Port

4× 4-40 UNC ↧ 0.250″ [6.35 mm]

DIMENSIONS3 WEIGHT4
Model Height Width Depth A B C E F G I
EPC, EPCD 4.203 in 2.250 in 1.700 in 0.313 in 0.850 in 0.775 in 0.390 in 1.310 in 0.275 in 1.975 in 15.0 oz
(IP66/67) 106.76 mm 57.15 mm 43.18 mm 7.95 mm 21.59 mm 19.69 mm 9.91 mm 33.27 mm 6.99 mm 50.17 mm 425.2 g
3 Port type, port locations, and other body dimensions may be customized. Contact Alicat for more information.
4 Maxmium product weights shown. Total device weight may vary depending on actual model configuration. Contact Alicat for more information.

DOC-SPECS-EPC-EPCD · REV 8, 17 Jan 2022 4 ⁄ 4