-|Transparent Guide|-

Rectangular Inductive Proximity Sensors

(□ 17/25/30/40 mm) Ordering Information Specifications ■ PSN40

PS Series (DC 3-wire)

53 • Bracket
This is only for reference, the actual product does not support all combinations. Standard type /
Installation Standard type 52
For selecting the specified model, follow the Autonics website. Upper side type
47

INSTRUCTION MANUAL
PSN17- PSN17- PSN25- PSN30- PSN30- PSN40-
Model
PSN ❶ - ❷ ❸ ❹ ❺ - ❻ 5D□□-□ 8D□□-□ 5D□ 10D□ 15D□ 20D□ Ø 4, 2 m B, 2-M5

2-5.5
Sensing side length 18 mm 18 mm 25 mm 30 mm 30 mm 40 mm
❶ Sensing side length ❹ Control output Sensing distance 5 mm 8 mm 5 mm 10 mm 15 mm 20 mm

30
Number: Side length of head (unit: mm) N: NPN Normally Open Setting distance 0 to 3.5 mm 0 to 5 mm 0 to 3.5 mm 0 to 7 mm 0 to 10.5 mm 0 to 14 mm

30
40

22
TCD210251AC N2: NPN Normally Closed Hysteresis ≤ 10 % of sensing distance
A 2-Ø 5.5
P: PNP Normally Open Standard sensing 18 × 18 25 × 25 25 × 25 30 × 30 45 × 45 60 × 60
P2: PNP Normally Closed target: iron × 1 mm × 1 mm × 1 mm × 1 mm × 1 mm × 1 mm 6
35
Response
❷ Sensing distance ❺ Sensing side 700 Hz 200 Hz 300 Hz 250 Hz 200 Hz 100 Hz
Thank you for choosing our Autonics product. frequency 01)
Number: Sensing distance (unit: mm) 15.5
Read and understand the instruction manual and manual thoroughly before No-mark: Standard type Affection by

40.8
± 10 % for sensing distance at ambient temperature 20 ℃
using the product. U: Upper side type temperature

25.8
19.8
For your safety, read and follow the below safety considerations before using. Indicator Operation indicator (red)
❸ Power supply ❻ Frequency

24
For your safety, read and follow the considerations written in the instruction Approval ᜢ᜽ᜫ ᜢ᜽ᜫ ᜢ᜽ᜫ ᜢ᜽ᜫ ᜢ᜽ᜫ ᜢ᜽ᜫ 40

2
D: 12 - 24 VDCᜡ No-mark: Standard type

9.3
manual, other manuals and Autonics website. Unit weight ≈ 62 g ≈ 62 g ≈ 71 g ≈ 96 g ≈ 96 g ≈ 135 g Standard type
F: Differential frequency type (package) (≈ 83 g ) (≈ 83 g ) (≈ 103 g ) (≈ 165 g ) (≈ 165 g ) (≈ 225 g )
Keep this instruction manual in a place where you can find easily.
The specifications, dimensions, etc. are subject to change without notice for product
Setting Distance Formula
01) The
 response frequency is the average value. The standard sensing target is used and the width is set as
2 times of the standard sensing target, 1/2 of the sensing distance for the distance.
improvement. Some models may be discontinued without notice.
Product Components Power supply 12 - 24 VDCᜡ (ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDCᜡ Sensing target Sensing target
Follow Autonics website for the latest information. Detecting distance can be changed : Up-Down movement
Current consumption ≤ 10 mA : Right-Left movement
PSN17 PSN25 PSN30 PSN40 by the shape, size or material of the
Control output ≤ 200 mA
target.
Safety Considerations
Product ×1 ×1 ×1 ×1
Residual voltage ≤ 1.5 V Sa Sn Sa Sn
Instruction manual × 1 ×1 ×1 ×1 For stable sensing, install the unit
Surge protection circuit, output short over current protection circuit,
• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards. Bracket ×1 ×1 ×1 ×1 Protection circuit within the 70 % of sensing distance.
reverse polarity protection
• ᜸ symbol indicates caution due to special circumstances in which hazards may occur. Bolt M3 × 2 M4 × 2 M4 × 2 M5 × 2 Setting distance (Sa)
Insulation type ≥ 50 MΩ (500 VDCᜡ megger)
= Sensing distance (Sn) × 70 %
Between the charging part and the case: 1,500 VACᜠ 50/60 Hz for 1
᜸ Warning Failure to follow instructions may result in serious injury or death. Dielectric strength
min
Connections 1 mm double amplitude at frequency 10 to 55 Hz in each X, Y, Z
01. Fail-safe device must be installed when using the unit with machinery that Vibration
direction for 2 hours Mutual-interference & Influence by Surrounding Metals
may cause serious injury or substantial economic loss. (e.g. nuclear power ■ Cable type Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times
control, medical equipment, ships, vehicles, railways, aircraft, combustion
Ambient temp. -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation)
■ Mutual-interference
apparatus, safety equipment, crime/disaster prevention devices, etc.) Brown Brown
Failure to follow this instruction may result in personal injury, economic loss or Ambient humi. 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) When plural proximity sensors are mounted in a close row, malfunction of sensor may
fire. LOAD
Black Protection structure IP67 (IEC standard) be caused due to mutual interference.
02. Do not use the unit in the place where flammable/explosive/corrosive gas, NPN 12-24 VDCᜡ PNP 12-24 VDCᜡ
Black Connection Cable type model Therefore, be sure to provide a minimum distance between the two sensors, as below
high humidity, direct sunlight, radiant heat, vibration, impact, or salinity LOAD
may be present. Wire spec. Ø 4 mm, 3-wire, 2 m table.
Failure to follow this instruction may result in explosion or fire. Blue Blue
Connector spec. AWG 22 (0.08 mm, 60-core), insulator diameter: Ø 1.25 mm [Face to Face] [Parallel]
03. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire. ■ Inner circuit (NPN output) ■ Inner circuit (PNP output) Case: Heat-resistant ABS,
B
Material
04. Do not connect, repair, or inspect the unit while connected to a power standard type cable (black): polyvinyl chloride (PVC)
source. A
Failure to follow this instruction may result in fire.
05. Check 'Connections' before wiring.
LOAD Dimensions

CIRCUIT
CIRCUIT

Failure to follow this instruction may result in fire.

• Unit: mm, For the detailed dimensions of the product, follow the Autonics web site. ■ Differential frequency
LOAD
᜸ Caution Failure to follow instructions may result in injury or product damage. A Operation indicator (red) B Tap hole When the several proximity sensors are installed closely each other, install standard
type and differential frequency type sensors alternativamently to prevent mutual
■ PSN17
01. Use the unit within the rated specifications. 35.6 • Bracket interference due to frequency interference.
Failure to follow this instruction may result in fire or product damage. 30.8 B, 2-M3 16 Sensing target
02. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Operation Timing Chart

2-3.5
Failure to follow this instruction may result in fire.

18
11
Normally open Normally closed

7.5
18
11
Cautions during Use Presence Presence A
5
Sensing target 10
Nothing Nothing Standarad Standarad
• Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected 32 Differential Differential
accidents. Operation Operation frequency frequency
Load

18

18
• 12-24 VDCᜡ power supply should be insulated and limited voltage/current or Class 2,

1.2
■ Influence by surrounding metals

8.5
Return Return

8.4
SELV power supply device.
18 Standard type / Upper side type
• Use the product, after 0.8 sec of supplying power. NPN H H When sensors are mounted on metallic panel, it must be prevented sensors from being
• Wire as short as possible and keep away from high voltage lines or power lines, to output ■ PSN25
Output L L affected by any metallic object except target. Therefore, be sure to provide a minimum
prevent surge and inductive noise. Do not use near the equipment which generates A
Ø 4, 2 m • Bracket
voltage H H distance as below chart.
strong magnetic force or high frequency noise (transceiver, etc.). PNP B, 2-M4 17.5
In case installing the product near the equipment which generates strong surge (motor, output L L • Standard type • Upper side type
welding machine, etc.), use diode or varistor to remove surge.

18
25
• This unit may be used in the following environments. Operation ON ON
m
- Indoors (in the environment condition rated in ‘Specifications’)

25
18

12
indicator (red) OFF OFF 35.5 2-Ø 4.2 d
- Altitude max. 2,000 m d
39 3.5
- Pollution degree 2 m m Earth-plate

2-4.5
- Installation category II 31.5 m

11.8 c

8.8
25.3

Cautions for Installation (unit: mm)

12.3

2
9.7
25 Model
Standard type PSN17-5 PSN17-8 PSN25 PSN30-10 PSN30-15 PSN40
• Install the unit correctly with the usage environment, location, and the designated Item
■ PSN30 A 30 48 30 60 90 120
specifications.
48.5 2-Ø 4.5 • Bracket B 36 40 40 50 65 70
• Do NOT impacts with a hard object or excessive bending of the wire lead-out. It may Ø 4, 2 m B, 2-M4 17.8 c 4 4 4 5 5 5
cause damage the water resistance.
d 15 24 15 30 45 60
• Do NOT pull the Ø 4 mm cable with a tensile strength of 30 N or over.
m 18 20 20 25 35 35
It may result in fire due to the broken wire.
30

22

30.5
• When extending wire, use AWG 22 cable or over within 200 m.

22

16
A
• Refer to the table below for the screw tightening torque when mounting the bracket.
3.5

2-4.3
PSN17 PSN25 PSN30 PSN40 33.5
Tightening torque 0.49 N m 0.98 N m 0.98 N m 0.98 N m
14
30

20
15.5

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

9

www.autonics.com | +82-2-2048-1577 | [email protected]

30 53
15

2
Standard type