Scribd
Upload
14 views2 pages

Tylose H 20 P2 Acar Kimya 20151218 135636

Tylose® H 20 P2 is a hydroxyethyl cellulose product with a viscosity of 20 mPa·s, primarily used in self-levelling floor compounds. It has low water retention and sag resistance, but high influence on cement hydration and heat stability. Safety precautions are necessary due to dust explosion hazards, and it should be stored in a dry place to maintain quality.

Uploaded by

Saad Azzouni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
14 views2 pages

Tylose H 20 P2 Acar Kimya 20151218 135636

Tylose® H 20 P2 is a hydroxyethyl cellulose product with a viscosity of 20 mPa·s, primarily used in self-levelling floor compounds. It has low water retention and sag resistance, but high influence on cement hydration and heat stability. Safety precautions are necessary due to dust explosion hazards, and it should be stored in a dry place to maintain quality.

Uploaded by

Saad Azzouni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Tylose® H 20 P2

Technical Data Sheet

O OH CH, CH2, CH3

Product properties

Constitution: Hydroxyethyl cellulose

Etherification: standard etherification Delayed solubility: yes

Particle size: powder

Level of viscosity: 20 mPa·s


according to Höppler

Recommended fields of application

Self levelling floor compounds

This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not
therefore be construed as guaranteeing specific properties of the products described or their suitability for a particular application. Any existing
industrial property rights must be observed. The quality of our products is guaranteed under our General Conditions of Sale.

SE Tylose GmbH & Co.KG · Rheingaustraße 190-196 · D-65203 Wiesbaden · Tel: +49 611 962-8571 · Fax: +49 611 962-9267 · www.SETylose.de · [email protected]

05/2013
Tylose® H 20 P2
Technical Data Sheet

Application performance

Consistency development: moderate Water retention: very low

Final consistency: very low Influence on cement hydration: high

Sag resistance: very low Heat stability: very high

Water demand: very low

Packaging, Storage, Safety instructions

Like all fine-particle organic substances, cellulose ethers constitute a dust explosion hazard. Dust formation
and deposits must be kept to a minimum so that no ignitable dust/air mixtures can form. Ignition sources such
as naked flames, hot surfaces, sparks and static electricity should be avoided. Tylose starts to decompose at
about 200°C. Its ignition temperature is >360°C. Tylose burns easily and the fire may spread.

When stored in closed containers, or in its original packaging in a dry place at room temperature, Tylose can
be kept for a long time. In the case of high viscosity grades, a slow loss of viscosity can be measured after
lengthy storage (>1 year). Tylose absorbs water from moist air. Once opened, container must be resealed and
kept tightly closed.

This Tylose-type is supplied in multi-ply paper bags with polyethylene intermediate layer and/or in big bags.

This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not
therefore be construed as guaranteeing specific properties of the products described or their suitability for a particular application. Any existing
industrial property rights must be observed. The quality of our products is guaranteed under our General Conditions of Sale.

SE Tylose GmbH & Co.KG · Rheingaustraße 190-196 · D-65203 Wiesbaden · Tel: +49 611 962-8571 · Fax: +49 611 962-9267 · www.SETylose.de · [email protected]

05/2013

You might also like