Paging Adapter Amplifier Integration Guide

Algo Support, 604-454-3792

[email protected]
www.algosolutions.com 2020-07-10 v2.6 1
 Table of Contents
➢ Paging Adapter Hardware Interface
▪ 8301 Paging Adapter & Scheduler………………….………………...6
▪ 8373 Zone Paging Adapter………………………………….……….....7
▪ Hybrid IP & Analog Infrastructure Integration……………………...9
➢ Paging Amplifier Wiring Diagrams
▪ Adastra RM60/120/240S with 8301……………………..……..………11
▪ Adastra RM60/120/240S with 8373……………………..……..………12
▪ AT&T/Lucent PagePal with 8301……………………………..…….…13
▪ AT&T PagePac 20 PowerMate ……………………………………...…14
▪ Bogen C35/C60/C100 with 8301………...………….………………….15
▪ Bogen GS35/GS60/GS100/GS150/GS250 with 8301………………..16
▪ Bogen PCM2000 with 8301……………...………….…………………..17
▪ Bogen TPU-35/60/100/250 with 8301…………………….……………18
▪ Bogen TPU-35/60/100/250 with 8373…………………………….……19 2
 Table of Contents
➢ Paging Amplifier Wiring Diagrams (continued)
▪ Bogen UTI with 8301…………………………………….….……………20
▪ Crown 135MA/160MA with 8301……………….....………….………...21
▪ Crown CDI 1000/2000/4000 with 8301……………...……….………...22
▪ Inter-M PA-920/935 with 8301………………......…...……….………...23
▪ Inter-M PA-60/120/240 with 8301………………........……….………...24
▪ Paso 3000 Series with 8301………………......…...……….…...……...25
▪ TOA BG-115/130 with 8301…………...……………………….………...26
▪ TOA BG-220/235 with 8301………………….…………………………..27
▪ TOA BG-1015/1030/1060/1120 with 8301…............…….…………....28
▪ TOA BG-2035/2060/2120 with 8301………………...……….………....29
▪ TOA 500 Series with 8301………………............…...……….………...30
▪ Valcom V-2000a with 8301………………...………………….………...31
3
 Table of Contents
➢ Paging Amplifier Wiring Diagrams (continued)
▪ Valcom V-2001a with 8301………………...………………….………...32
▪ Valcom V-2003A with 8301…………………………………….………..33
▪ Valcom V-2006A with 8301……………………………………….……..34
▪ Valcom V-9940 with 8301………………………………………………..35
▪ Valcom V-9941A with 8301 ……………………………………………..36
▪ Valcom V-1094A with 8301…………………………………….………. 37
▪ Valcom V-2924A with 8301 ……………………………………………..38
▪ Valcom VIP-801A with 8301 ……………………………..……………..39
▪ Viking PA-2A with 8301………………………………………….………40
▪ Viking PA-15 with 8301………………………………………….……….41
▪ Viking PA-60 with 8301………………………………………….……….42

4
 Paging Adapter
Hardware Interface

5
 8301 Paging Adapter & Scheduler

➢ SIP (50 Page ext., 10 Music Input

Emergency Alert ext. &
10 Ring ext.)
➢ Multicast Send &
Receive
➢ Scheduler for
Automated Tones &
Announcements
➢ 1GB Memory
6
 8373 Zone Paging Adapter

➢ SIP (50 Page ext.)

➢ Switches up to:
➢ 500W at 70V
➢ 180W at 25V
➢ 720W at 100V
➢ Multicast Send & Receive

7
8373 Zone Paging Adapter

8
 Hybrid IP & Analog Infrastructure
Integration

SIP Call
Simultaneous
Line Level Output
to Amplifier

Simultaneous Multicast
To Speakers, Strobes &
Phones

Analog Amplifier &

Speakers

9
Paging Amplifier
Wiring Diagrams

10
 8301 Installation Example with
Adastra RM60/120/240S

Recommended: use an aux cable and strip the leads

on one end. Connect the positive and negative
(usually red and black) terminals to the Line Out. On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
To connect the other end to the amplifier input
Mic/Line 2, use a 3.5 mm to 6.3 mm adapter.

11
 8373 Installation Example with
Adastra RM60/120/240S

Output from
Amplifier
(25/70/100V)
Output to Analog
Speaker Channels

Recommended: use an aux cable and strip the leads

on one end. Connect the positive and negative
(usually red and black) terminals to the Line Out. On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
To connect the other end to the amplifier input
Mic/Line 2, use a 3.5 mm to 6.3 mm adapter.

12
 8301 Installation Example with
AT&T/Lucent PagePal

Set the PagePal to DL (Dry Loop) mode using the

switch in the front

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

13
 8301 Installation Example with
AT&T PagePac 20 PowerMate

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

14
 8301 Installation Example with
Bogen C35/C60/C100

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.

15
 8301 Installation Example with
Bogen GS35/GS60/GS100 &
GS150/GS250
Set the switch to the
“TEL” position

Ensure JP1 Phantom

Power Jumper is in
the OFF position

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.

16
8301 Installation Example with
Bogen PCM2000

Before connecting, power off PCM2000 system. Set the dip switch as
demonstrated above (CC switch down and P/P switch middle).

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.

To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).

17
8301 Installation Example with
Bogen TPU-35/60/100/250

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.

18
8373 Installation Example with
Bogen TPU-35/60/100/250
The 8373 is designed to provide a Line Out for audio to
a traditional amplifier.

Loop the power of the amplifier into the 8373 to

switch up to 500W (for 70V output) into 1-3 audio
channels. At 25V the 8373 can switch up to 180W and
720W at 100V.

The speaker runs will be connected to the channel

outputs on the 8373.

On the 8373 web interface, go to Basic Settings -> Features and set the Line Out
Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

19
 8301 Installation Example with
Bogen UTI1

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Set the horizontal switch to “CONT” and the vertical to “Page Port”. Output Level to “0dBm 600 ohm (0.775 Vrms)”.

20
 8301 Installation Example with
Crown 135MA/160MA

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Set switch 1 to “Line” position.
Out Analog Output Level to “0dBv 10k (1.0 Vrms)”.

21
 8301 Installation Example with
Crown CDI 1000/2000/4000

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “+4dBu 10k (1.23 Vrms)”.

Note: Channel 1 or 2 may be used.

22
 8301 Installation Example with
Inter-M PA-920/935

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

23
 8301 Installation Example with
Inter-M PA-60/120/240

Connect the Line Out pair on the 8301 to

the + and – terminals on one of the Inter-M On the 8301 web interface, go to Basic Settings -> Features and set the Line
inputs. Move the input selection switch to Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
the “Line” position.

24
 8301 Installation Example with
Paso 3000 Series

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

25
 8301 Installation Example with
TOA BG-115/130

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Set the highlighted switch to the TEL position
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

26
 8301 Installation Example with
TOA BG-220/235

Set DIP switch 8 to the OFF position and be On the 8301 web interface, go to Basic Settings -> Features and set the Line
sure to turn off the power before performing Out Analog Output Level to “-10dBm 600 ohm (0.245 Vrms)”.
this step.

27
 8301 Installation Example with
TOA BG-1015/1030/1060/1120

The impedance is set from factory to 10 kΩ. To switch to On the 8301 web interface, go to Basic Settings -> Features and set the Line
600 Ω, change the position of the unit's internal jumper Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
switch JP204 as per diagram below.

28
 8301 Installation Example with
TOA BG-2035/2060/2120

Set the DIP switches as per below:

Function Switches A (upper terminal)

• Switch 2 – Off On the 8301 web interface, go to Basic Settings -> Features and set the Line
• Switch 4 – On Out Analog Output Level to “-20dBm 600 ohm (0.077 Vrms)”.

Function Switches B (lower terminal)

• DIP Switch 2 – On

29
 8301 Installation Example with
TOA 500 Series

Set the Phantom switch above the input to

the off position.
On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “-10dBm 600 ohm (0.245 Vrms)”.
Recommended: Algo 2504 Output XLR-Mini
Female to XLR Male

30
 8301 Installation Example with
Valcom V-2000a
Set the Battery Feed switch off
before connecting the 8301

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “-10dBm 600 ohm (0.245 Vrms)”.

31
 8301 Installation Example with
Valcom V-2001a
SW1 Off for Page Port Access

The 8301 Line Out (terminal 3 and 4) connects to either the

Tip and J3) using an RJ11 modular connector or the Page T
and Page R inputs on the Valcom V-2001A via a 2-wire
connection to the terminal strip.

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “-10dBm 600 ohm (0.245 Vrms)”.

32
8301 Installation Example with
Valcom V-2003a

On the Valcom V2003a switch SW3, set 4, 7 and 10 to

the off position (up position). Also set SW2 to off
position.

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “-10dBm 600 ohm (0.245 Vrms)”.

To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).

33
8301 Installation Example with
Valcom V-2006a

Set the Battery Feed switch to the off position for Page
Port access on the V2006a.

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “-10dBm 600 ohm (0.245 Vrms)”.

To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).

34
 8301 Installation Example with
Valcom V-9940

Ensure that only DIP Switches 1 and 8 are ON. If the

device is not working try turning DIP Switch 1 OFF.

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “-20dBm 600 ohm (0.077 Vrms)”.

35
 8301 Installation Example with
Valcom V-9941A

Note there will be no talk back from the Valcom

speakers.

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.

36
8301 Installation Example with
Valcom V-1094A

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.

37
8301 Installation Example with
Valcom V-2924A

Set the Battery Feed switch (SW4) to off for Page Port
access.

Note there will be no talkback via the Valcom V-2924A.

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “-10dBm 600 ohm (0.245 Vrms)”..

To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).

38
 8301 Installation Example with
Valcom VIP-801A

On the 8301 web interface, go to Basic Settings -> Features and set the Line Out Analog
Output Level to “-10dBm 600 ohm (0.245 Vrms)”..

39
8301 Installation Example with
Viking PA-2A

Set DIP switch 4 for talk battery to the OFF position on

the PA-2A to prevent damaging the 8301.

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

40
8301 Installation Example with
Viking PA-15

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

41
 8301 Installation Example with
Viking PA-60

On the 8301 web interface, go to Basic Settings -> Features and set the Line
Out Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.

If there are speakers connected to both channels, then an 8301 per channel
will be required. One 8301 can be SIP registered and configured to Multicast
to the second for zone paging including All Call.

42
Please contact us if there are additional amplifier
models you wish to see included in this guide.

Support (604) 454-3792

[email protected]

43