1N5400 THRU 1N5408

GENERAL PURPOSE PLASTIC RECTIFIER

Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes

DO-201AD FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ High surge current capability
1.0 (25.4) ♦ Construction utilizes void-free molded plastic technique
♦ 3.0 Ampere operation at
MIN.

0.210 (5.3) TL=105°C with no thermal runaway

0.190 (4.8)
DIA. ♦ Typical IR less than 0.1µA
♦ High temperature soldering guaranteed:
0.375 (9.5)
0.285 (7.2) 250°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension

0.052 (1.32)
MECHANICAL DATA
0.048 (1.22) 1.0 (25.4) Case: JEDEC DO-201AD molded plastic body
DIA. MIN.
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Dimensions in inches and (millimeters)
Weight: 0.04 ounce, 1.1 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

1N 1N 1N 1N 1N 1N 1N 1N 1N
SYMBOLS 5400 5401 5402 5403 5404 5405 5406 5407 5408 UNITS

*Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 500 600 800 1000 Volts
*Maximum RMS voltage VRMS 35 70 140 210 280 350 420 560 700 Volts
*Maximum DC blocking voltage to TA=150°C VDC 50 100 200 300 400 500 600 800 1000 Volts
*Maximum average forward rectified current
I(AV) 3.0 Amps
0.5” (12.5mm) lead length at TL=105°C
*Peak forward surge current
8.3ms single half sine-wave superimposed on IFSM 200.0 Amps
rated load (JEDEC Method) at TL=105°C
*Maximum instantaneous forward voltage at 3.0A VF 1.2 Volts
*Maximum DC reverse current TA=25°C 10.0
IR µA
at rated DC blocking voltage TA=150°C 500.0
*Maximum full load reverse current full cycle
IR(AV) 500.0 µA
average, 0.5" (12.5mm) lead length at TL=105°C
Typical junction capacitance (NOTE 1) CJ 30.0 pF
*Typical thermal resistance (NOTE 2) RΘJA 20.0 °C/W
Maximum DC blocking voltage temperature TA +150 °C
*Operating junction temperature range TJ -50 to +170 °C
*Storage temperature range TSTG -50 to +170 °C

NOTES:
(1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(2) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, P.C.B. mounted with 0.8 x 0.8” (20 x 20mm) copper heatsinks
*JEDEC registered value

4/98
 RATINGS AND CHARACTERISTIC CURVES 1N5400 THRU 1N5408
FIG.1 - FORWARD CURRENT DERATING CURVE
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
8.0 SURGE CURRENT
AVERAGE FORWARD RECTIFIED CURRENT,

400

INSTANTANEOUS FORWARD CURRENT,

L=0.31” (0.79mm) L=0.25” (6.3 mm) 8.3ms SINGLE HALF SINE WAVE
7.0 (JEDEC Method)
TL=LEAD TEMPERATURE
with BOTH LEADS HEAT TL=105°C
6.0 SINK MOUNTED with
LENGTH (L) AS SHOWN 1.0 CYCLE
5.0 60 Hz RESISTIVE OR

AMPERES
AMPERES

INDUCTIVE LOAD
4.0
L=0.50” (12.7 mm)
100
3.0

2.0
TA=AMBIENT TEMPERATURE
1.0 0.375” (9.5mm) LEAD LENGTH
P.C. B. MOUNTING 40
0 1.0 10 100
40 60 80 100 120 140 160 180
NUMBER OF CYCLES AT 60 HZ
TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS

FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
100 100

INSTANTANEOUS REVERSE CURRENT,

10
INSTANTANEOUS FORWARD CURRENT,

10
TJ=25°C
TJ=150°C
PULSE WIDTH=300µs

MICROAMPERES
1% DUTY CYCLE
AMPERES

1
1
TJ=100°C

0.1

0.1
TJ=25°C

0.01
0 20 40 60 80 100

0.01 PERCENT OF RATED PEAK REVERSE

0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 VOLTAGE,%

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100
TRANSIENT THERMAL IMPEDANCE, °C/W

100
TJ=25°C
70 f=1.0 MHz
Vsig=50mVp-p
JUNCTION CAPACITANCE, pF

10

10
1

0.1
1 0.01 0.1 1 10 100
0.1 1 10 100
t, PULSE DURATION, sec.
REVERSE VOLTAGE, VOLTS