Scribd
Upload
11 views

3.3.12-packet-tracer - -vlan-configuration

The document outlines the configuration of VLANs in a network using Packet Tracer, detailing the addressing table for devices and objectives for verifying and configuring VLANs. It includes steps for creating VLANs, assigning them to ports, and ensuring connectivity between devices on the same VLAN. The document emphasizes the benefits of VLANs, such as improved security and reduced broadcast traffic.

Uploaded by

mearckfrancisvoughnlol
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views

3.3.12-packet-tracer - -vlan-configuration

The document outlines the configuration of VLANs in a network using Packet Tracer, detailing the addressing table for devices and objectives for verifying and configuring VLANs. It includes steps for creating VLANs, assigning them to ports, and ensuring connectivity between devices on the same VLAN. The document emphasizes the benefits of VLANs, such as improved security and reduced broadcast traffic.

Uploaded by

mearckfrancisvoughnlol
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Packet Tracer - VLAN Configuration

Addressing Table
Device Interface IP Address Subnet Mask VLAN

PC1 NIC 172.17.10.21 255.255.255.0 10


PC2 NIC 172.17.20.22 255.255.255.0 20
PC3 NIC 172.17.30.23 255.255.255.0 30
PC4 NIC 172.17.10.24 255.255.255.0 10
PC5 NIC 172.17.20.25 255.255.255.0 20
PC6 NIC 172.17.30.26 255.255.255.0 30

Objectives
Part 1: Verify the Default VLAN Configuration
Part 2: Configure VLANs
Part 3: Assign VLANs to Ports

Background
VLANs are helpful in the administration of logical groups, allowing members of a group to be easily moved,
changed, or added. This activity focuses on creating and naming VLANs, and assigning access ports to
specific VLANs.

Part 1: View the Default VLAN Configuration


Step 1: Display the current VLANs.
On S1, issue the command that displays all VLANs configured. By default, all interfaces are assigned to
VLAN 1.

Step 2: Verify connectivity between PCs on the same network.


Notice that each PC can ping the other PC that shares the same subnet.
• PC1 can ping PC4
• PC2 can ping PC5
• PC3 can ping PC6
Pings to hosts on other networks fail.

What benefits can VLANs provide to the network?

- There are a lot benefits that having VLAN can provide, it make the security more secure, to have less cost ,
for management of designated network . To avoid the broadcast to all devices.

© 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 3 www.netacad.com
Packet Tracer - VLAN Configuration

Part 2: Configure VLANs


Step 1: Create and name VLANs on S1.
a. Create the following VLANs. Names are case-sensitive and must match the requirement exactly:
• VLAN 10: Faculty/Staff
S1#(config)# vlan 10
S1#(config-vlan)# name Faculty/Staff
b. Create the remaining VLANS.
• VLAN 20: Students
• VLAN 30: Guest(Default)
• VLAN 99: Management&Native
• VLAN 150: VOICE

Step 2: Verify the VLAN configuration.


Which command will only display the VLAN name, status, and associated ports on a switch?
In the privileged exec mode, enter the command show vlan brief

Step 3: Create the VLANs on S2 and S3.


Use the same commands from Step 1 to create and name the same VLANs on S2 and S3.

Step 4: Verify the VLAN configuration.

Part 3: Assign VLANs to Ports


Step 1: Assign VLANs to the active ports on S2.
a. Configure the interfaces as access ports and assign the VLANs as follows:
• VLAN 10: FastEthernet 0/11
S2(config)# interface f0/11
S2(config-if)# switchport mode access
S2(config-if)# switchport access vlan 10
b. Assign the remaining ports to the appropriate VLAN.
• VLAN 20: FastEthernet 0/18
• VLAN 30: FastEthernet 0/6

Step 2: Assign VLANs to the active ports on S3.


S3 uses the same VLAN access port assignments as S2. Configure the interfaces as access ports and assign
the VLANs as follows:
• VLAN 10: FastEthernet 0/11
• VLAN 20: FastEthernet 0/18
• VLAN 30: FastEthernet 0/6

© 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 3 www.netacad.com
Packet Tracer - VLAN Configuration

Step 3: Assign the VOICE VLAN to FastEthernet 0/11 on S3.


As shown in the topology, the S3 FastEthernet 0/11 interface connects to a Cisco IP Phone and PC4. The IP
phone contains an integrated three-port 10/100 switch. One port on the phone is labeled Switch and connects
to F0/4. Another port on the phone is labeled PC and connects to PC4. The IP phone also has an internal port
that connects to the IP phone functions.
The S3 F0/11 interface must be configured to support user traffic to PC4 using VLAN 10 and voice traffic to
the IP phone using VLAN 150. The interface must also enable QoS and trust the Class of Service (CoS)
values assigned by the IP phone. IP voice traffic requires a minimum amount of throughput to support
acceptable voice communication quality. This command helps the switchport to provide this minimum amount
of throughput.
S3(config)# interface f0/11
S3(config-if)# mls qos trust cos
S3(config-if)# switchport voice vlan 150

Step 4: Verify loss of connectivity.


Previously, PCs that shared the same network could ping each other successfully.
Study the output of from the following command on S2 and answer the following questions based on your
knowledge of communication between VLANS. Pay close attention to the Gig0/1 port assignment.
S2# show vlan brief
VLAN Name Status Ports

1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4


Fa0/5, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/12, Fa0/13, Fa0/14
Fa0/15, Fa0/16, Fa0/17, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig0/1, Gig0/2
10 Faculty/Staff active Fa0/11
20 Students active Fa0/18
30 Guest(Default) active Fa0/6
99 Management&Native active
150 VOICE active

Try pinging between PC1 and PC4.

Although the access ports are assigned to the appropriate VLANs, were the pings successful? Explain.
- No, because the ports between the switches are in vlan 1 and pc1 and pc4 are in vlan 10,

What could be done to resolve this issue?


- The ports should be configured between the switches as trunk ports so it can carry multiple vlans.

© 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 3 www.netacad.com

You might also like