Scribd
Upload
15 views

Column Base Design - 2

The document outlines the design calculations for a column base for the ELLA PLAZA project, specifying loading conditions, soil bearing capacity, and required base area. It includes detailed calculations for shear stress, punching shear, and bending reinforcement, ensuring compliance with structural safety standards. The final checks confirm that the design meets the necessary criteria for ultimate shear stress.

Uploaded by

Ncho Ukot
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views

Column Base Design - 2

The document outlines the design calculations for a column base for the ELLA PLAZA project, specifying loading conditions, soil bearing capacity, and required base area. It includes detailed calculations for shear stress, punching shear, and bending reinforcement, ensuring compliance with structural safety standards. The final checks confirm that the design meets the necessary criteria for ultimate shear stress.

Uploaded by

Ncho Ukot
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Project: ELLA PLAZA Job Ref:

COLUMN BASE DESIGN Date:


Sheet No:
Structure: COLUMN BASE TYPE I Made by: T.J
Checked by:

REF CALCULATIONS OUTPUT

LOADING
Total ultimate load from superstructure = 309.65 KN Col: 225 x 225
Total Service load = 221.18 KN h = 225 mm
Soil bearing capacity = 150 KN/m 2 b = 225 mm
Assume footing weight is 10% of total service load
Area of base required = (243.30 ÷ 150) = 1.62 m2 Base :
Prov. = 1.00 m x 1.00 m = 1.00 m2 L = 1.00 m
Perimeter = 2 x 225 + 225 = 900 mm B = 1.00 m
Net pressure = (309.65 ÷ 1.00 ) - (0.3 x 24 x 1.4) = 299.57 KN/m 2 h= 300 mm
d = 244
DESIGN
Shear strees,vc = 309.7 x 10 3 = 1.41 N/mm 2 <0.8 √fcu
900 x 244
Punching shear : h= 300 Ø= 12 d = 244
critical perimeter = 900 + 12 x 244 = 3828 mm
2
Area within crit. perimeter = ( 225 + 3 x 244 ) = 9.16E+05 mm
Punching shear force,V = 299.57 x ( 1.00 - 0.92 ) = 25.21 KN
3 2 2
Punching shear stress,v c = 25.21 x 10 = 0.03 N/mm < 0.34 N/mm
3828 x 244
1.00 m

225

1.00 m 225

Bending Reinforcement
fcu = 20 N/mm² fy = 400 N/mm²
h = 300 mm b = 1000
d = 244 mm Ø = 12 mm

Spans 0.98
Reinf. Limit As min = 0.13 % As max = 4 % 229.60
Moment M = 22.49 KN.m 189.10
k = M / (bd² fcu) = 0.019 k < 0.156
'Requires only tension reinforcement' z = 229.6 mm
As = M / (0.95fyz) = 258 mm²
< 390 390 As < As min 390 As = 390 mm² T12 @ 200 Btm
12000 2386.76 (BW) 565 mm²

Final check for punching shear


100As/bd = 0.23
Ultimate shear stress
At critical section 1.0d from the column face
V = 299.57 x 1 x 0.1 = 42.99 KN 0.34
v = 42.99 x 10 3 = 0.18 N/mm 2 < 0.34 N/mm 2
1000 x 244 Ok

You might also like