TEMPERATURE CONTROLLER POWER SUPPLY: STATUS LED DESCRIPTION WARNING GUIDELINES

UTC-221P Supply
100 to 270V AC, 50-60Hz
Voltage WARNING : Risk of electric shock.
Power
Consuption
(VA Rating)
4VA @ 230V AC MAX
2 345 1. To prevent the risk of electric shock, power supply to the
equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
being supplied.

2500
1
ENVIRONMENT CONDITION:
2. To reduce electro magnetic interference, use wire with
3 adequate rating and twists of the same of equal size shall
Operating Temp. 0°C to 55°C
be made with shortest connection.
UP to 95% RH
Relative Humidity 2 3. Cable used for connection to power source, must have a
(non-condensing)
cross section of 1mm or greater. These wires should have
Protection Level IP-65 (Front side) As per IS/IEC 1 - Control output indication insulations capacity made of at least 1.5kV.
(As per request) 60529 : 2001
2 - Auto tuning “ON” indication 4. When extending the thermocouple lead wires, always use
thermocouple compensation wires for wiring for the RTD
MECHANICAL INSTALLATION 3 - Blinking DP Will Indicate Delay time Count type, use a wiring material with a small lead resistance
(5 Ω max per line) and no resistance differentials among
Panel Cutout three wires should be present.
PV = Process Value Outline Dimension (mm)
Dimension (mm) KEY OPERATION 5. A better anti-noise effect can be expected by using
SV = Set Value
standard power supply cable for the instrument.
UTC 221P
ºC

TECHNICAL SPECIFICATION R
23 4 PV
68
FUNCTION
OPERATOR MODE
PRESS KEY INSTALLATION GUIDELINES
72 235 SV
INPUT SPECIFICATION: 1. This equipment, being built-in-type, normally becomes a
SET
TUNE

ENT To enter in parameter setting

part of main control panel and in such case the terminals
Input Range 85 68 do not remain accessible to the end user after installation
72 3 For start/stop PID auto tuning Press
J 0 to 600°C, and internal wiring.
6 sec
Input Types K 0 to 1200°C, 2. Do not allow pieces of metal, wire clippings, or fine metallic
PT-100 -99 to 400°C, To go in factory setting mode + fillings from installation to enter the product or else it may
PT.1 -99.9 to 400.0°C, TERMINAL CONNECTION lead to a safety hazard that may in turn endanger life or
Press 3 sec cause electrical shock to the operator.
J,K,PT-100 = 1°C
Resolution PARAMETER SETTING MODE
PT.1 = 0.1°C 3. Circuit breaker or mains switch must be installed between

Sensor input
+
±1% of FSD ± 1°C 1 L 100 ~ 8 To set parameter value power source and supply terminal to facilitate power ‘ON’
Indication 270V AC
Accuracy
TC or ‘OFF’ function. However this mains switch or circuit
(FSD:- Full Scale Deflection) 2 N
50/60 Hz
4VA 9
- breaker must be installed at convenient place normally
! To increment parameter value. accessible to the operator.
DISPLAY AND KEYS: RTD
3 NO 10
Made in India

Upper: 4 digit, 7 segment, 0.70” Red To decrement parameter value. 4. Use and store the instrument within the specified ambient
Display 4 C 11 temperature and humidity ranges as mentioned in this
Lower: 4 digit, 7 segment, 0.50” Green RELAY1
manual.
Set parameter to be save & exit.
Keys SET, INC, DEC, ENT
NC
5 12 MECHANICAL INSTALLATION GUIDELINES
DIMENSION:
6 - O/P 13 ! SAFETY PRECAUTION
Size 72 (H) x 72 (W) x 85 (D) mm 1. Prepare the panel cutout with proper dimensions as shown
S.S.R
above.
7 14
+

Panel Cutout 68 (H) x 68 (W) mm www.multispanindia.com

All safety related codifications, symbols and instructions that 2. Fit the unit into the panel with the help of clamp given.
CONTROL METHOD: appear in this operating manual or on the equipment must be 3. The equipment in its installed state must not come in close
Sensor Input strictly followed to ensure the safety of the operating personnel proximity to any heating source, caustic vapors, oil steam,
1) PID control with Auto-Tuning as well as the instrument.
Heating or other unwanted process byproducts.
2) ON-OFF control 8 8
If all the equipment is not handled in a manner specified by 4. Use the specified size of crimp terminal (M3.5 screws) to
Cooling ON-OFF control the manufacturer, it might impair the protection provided by the wire the terminal block. Tightening the screws on the
9 9 terminal block using the tightening torque of the range of
OUTPUT SPECIFICATION: equipment.
1.2 N.m.
Install jumper
Relay Output 10 10 when using 5. Do not connect anything to unused terminals.
Read complete instructions prior to installation
2 Wire RTD
Relay 1 Nos 3-Wire RTD 2-Wire RTD and operation of the unit.
MAINTENANCE
Relay Type 1C/O (NO-C-NC) WARNING : Risk of electric shock.
Rating 10A, 230V AC / 28V DC 1. The equipment should be cleaned regularly to avoid blockage
+

8 of ventilating parts.
SSR Drive Output
2. Clean the equipment with a clean soft cloth. Do not use
12V DC, 30mA DC isopropyl alcohol or any other cleaning agent.
9
Output Signal (On-Off condition)
Thermocouple 3. Fusible resistor must not be replaced by operator.
Relay parallel to SSR Page 1
 Auto Tuning:-
ERROR DISPLAY PARAMETER SETTING Control Parameter
The Auto-tuning function automatically computes
When an error has occurred the display indicates error codes Password and sets the Proportional band (Pb) , Integral time (It),
as given below. To ENTER CONTROL
Message PARAMETER Derivative time (dt), and cycle time as per process
ERROR MEANING
Set Point Setting characteristics.
IF PID SELECTED SET SETTING, ENTER “37”
Sensor is not connected or 34 Process Value PID
Tuning LED will turn “ON” during Auto-Tuning
OPEN Over range condition or
sensor break
234 Set Value Parameters If the power goes off before auto-tuning is completed,

key
auto-tuning will be restarted at next power ON.

ENT
SRE Sensor connection is reversed
set Set Point
Proportional
34 °C

Press
Band PID AUTO-TUNING
PV Press
234 234 SV key for 6 sec to start/stop
CORRECTIVE ACTION: Press SET key for 3 sec to PID auto-tuning
enter password Integral
Tuning
Check the sensor and the input wiring. If problem still exists, time LED Indication

key
Password Message
replace the sensor. And still if problem is not solved yet by the
user, then please contact company person
pass

SET
50 Derivative

Press
time
FACTORY SETTING
Basic Configuration Cycle time
34 To ENTER BASIC
234 Press + key
Password
CONFIGURATION
for 3 sec Message SETTING, ENTER “73” Manual Reset
fCst
YES no
Input
yes : Press ENT key to apply factory set
Press ENT key to save & exit
values as shown in table.
CONTROL FUNCTION
no : Press ENT key to escape
from factory setting.
Relay Mode
ON - OFF control (Heating)

RLY-OFF RLY-OFF
FACTORY SETTING
SR. PARAMETER VALUES Control Action S.V
Hysterisis
1 PB 20.0°C
2 IT 300 HYST

Temp.
key

RLY-ON
3 DT 75 RLY-ON
Delay Time
SET

4 CT 15 Sec RLY-OFF
Press

5 MR 0°C
RLY-ON
6 Offset 0°C
7 Hysteresis 3°C
8 Delay Time 6 Sec Time
Set Low Limit
ON OFF ON OFF

PARAMETER RANGE
ON - OFF control (Cooling)
Set High Limit
Sr. Parameter Range for J, K, PT100 Range for PT.1
1 PB 0.0 to 999.9 0 to 999.9
2 IT 0 to 9999 0 to 9999
3 DT 0 to 9999 0 to 9999
Offset HYST
4 CT 4 Sec to 99 Sec 4 Sec to 99 Sec
5 MR -9°C to +9°C -9.0°C to +9.0°C
6 OffSet -20°C to +20°C -20.0°C to +20.0°C S.V
Temp.

7 Hysteresis 1°C to 100°C 0.1°C to 100.0°C

RLY-OFF
8 Delay Time 1 Sec to 999 Sec 1 Sec to 999 Sec
Press ENT key to save & exit delay delay delay Specifications are subject to change, since development is a continuous process,
RLY-ON
Time Time Time So for more updated operating information and Support,
Please contact our Helpline: 9978991474/76/82 or
Time Email at [email protected] Ver:191201

OFF ON OFF ON OFF ON

Page 2