ASMB-975 LGA 3647 Dual Intel Xeon® Processor Scalable

Family Server Board with 12 DDR4, 4 PCIe x16 + 1 PCIe

x8+4 PCIe x4, 14 SATA3, 8 USB3.0, Dual 10GbE, IPMI
Startup Manual
Packing List Specifications

Before you begin installing your card, please make sure Standard M/B Functions
that the following items have been shipped:
• CPU: Dual LGA3647-P0 Intel Xeon® Processor Scalable
• 1 ASMB-975 Startup Manual Family series
• 1 Driver CD • BIOS: AMI 256 Mb SPI BIOS
• 2 Serial ATA HDD data cables • Chipset: Intel® C620 PCH
• 2 Serial ATA HDD power cables • System Memory: 12* DDR4-1866/2133/2400/2666
• 2 CPU power cables (8P) Registered ECC DIMM, Max. Capacity 384 GB
• 1 I/O port bracket Note 2: Due to the inherent limitations of the PC architec-
• 1 Warranty card ture, the system may not fully detect 384 GB
RAM when 384 GB RAM is installed.
If any of these items are missing or damaged, please • SATA Interface: 14 SATA3 6 Gb/s ports Intel Rapid
contact your distributor or sales representative immediately. Storage (for Windows only) (SATA0-SATA7 support soft-
ware RAID 0,1,10 & 5, SSATA0-SSATA5 support software
RAID 0,1,10 & 5 due to 2 SATA controller design)
Note 1: Acrobat Reader is required to view any PDF file.
• Serial Ports: Two RS-232 ( one on Rear I/O, and another
Acrobat Reader can be downloaded at: one via pin header)
https://www.adobe.com/downloads.html
• Keyboard/Mouse Header (KBMS1): Supports the stan-
(Acrobat is a trademark of Adobe)
dard PS/2 keyboard and mouse via PS/2 cable
• Watchdog Timer: 255 sec/min level timer intervals
• USB Port: Supports up to 8 USB 3.0 ports (4 ports from
onboard 20-pin header) and 3 USB 2.0 ports (1*Type-A,
2 ports from onboard 10-pin header)

VGA Interface
• Chipset: ASPEED AST2500/2510
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate

Ethernet Interface
• Interface: 10/100/1000 Mbps & 10Gb (only for LAN3 &
LAN4)
• Controller: LAN1/2: Intel I210; LAN3/4: Intel X557

Mechanical and Environment

• Dimensions (L x W): 358.1 x 330.2 mm (14.1” x 13”)
• Power Supply Voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
For more information on this and other Advantech • Power Consumption (mainboard only, excluding
products, please visit our website at: IO device): Max. load: [email protected], [email protected],
[email protected], [email protected], [email protected],
http://www.advantech.com [email protected], [email protected]
For technical support and service, please visit our • Operating Temperature: 0 ~ 40° C (depending on CPU)
support website at: • Weight: 1.5 kg (weight of board)

http://support.advantech.com

This manual is for the ASMB-975 series Rev. A1

Part No. 2001097500 1st Edition

Printed in China August 2017

ASMB-975 Startup Manual 1

 Jumpers and Connectors Jumpers and Connectors (Cont.)
The board has a number of jumpers that allow you to con-
PCIEX16_SLOT4 PCIE x16 slot (CPU1)
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors. PCIEX4_SLOT5 PCIE x4 slot (CPU0)
Connectors
PCIEX16_SLOT6 PCIE x16 slot (CPU1)
Label Function
PCIEX4_SLOT7 PCIE x4 slot (CPU0)
ATXPWR1 ATX 24 Pin main power connector PCIEX16_SLOT8 PCIE x16 slot (CPU0)
PCIEX8_SLOT9 PCIE x8 slot (CPU1)
Processor power connector
ATX12V1 SMBUS1 SMBus header
(for CPU0)

Processor power connector(for SPI_CN1 Connector for BIOS update tool

ATX12V2
CPU1)
SPI_SKT1 EC EEPROM
BH2 For optional battery kit
SYS_LED1 System LED connector
BMC_CN1, BMC_CN2 IPMI module header
SYSFAN0-SYSFAN7 System FAN connector
COM2 Serial port: RS-232
USB11 USB 2.0 port 11 (Type-A)
CPUFAN0,CPUFAN1 CPU FAN connector
USB 3.0 port 5,6,7,8 (20 pin
DIMMA1, DIMMB1, USB5_6,USB7_8
header)
DIMMC1, DIMMD1, DDR4 slot for CPU0
DIMME1, DIMMF1 VGA1_COM1 VGA+COM connector

VOLT1 Voltage display

DIMMG1, DIMMH1,
DIMMI1, DIMMJ1, DDR4 slot for CPU1
VROC1 Intel Virtual RAID (VROC) key
DIMMK1, DIMML1
Jumper list
EX_THR1 Connector for external thermistor
Label Function
GPIO1 GPIO connector
JCMOS1 CMOS clear
HDAUD1 Audio header
JME1 ME update
JFP1, JFP2, JFP3 Front panel header
JWDT1 Watch Dog Reset
External keyboard and mouse
KBMS1 PSON1 AT(1-2) / ATX(2-3)
connector (6 pin)
JCASE1 Alarm detection
RJ-45 LAN port 1 + USB 3.0 port
LAN1_USB1_2
1/2 connector JTHR_SEL To select on board or external thermistor
RJ-45 LAN port 2 + USB 3.0 port
LAN2_USB3_4
3/4 connector
JCMOS1/JME1: CMOS clear/ME update function
LPC1 TPM connector
Closed pins Result
SATA port 4/5 for M.2 2242 SATA
SSATA4, SSATA5 1-2 Keep CMOS data/Disable ME update*
SSD

PMBUS connector to 2-3 Clear CMOS data/Enable ME update

PMBUS1
communicate with power supply
*: Default
SATA0_1, SATA2_3,
Serial ATA0~7 1 2 3
SATA4_5, SATA6_7 1 2 3
SSATA0_1, SSATA2_3 sSATA port 0~3

SGPIO1,2 sSATA SGPIO header Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update

PCIEX4_SLOT1 PCIE x4 slot (CPU1)

PCIEX16_SLOT2 PCIE x16 slot (CPU0)

PCIEX4_SLOT3 PCIE x4 slot (CPU1)

2 ASMB-975 Startup Manual

 Jumpers and Connectors (Cont.) Software Installation
The CD disc contains a driver installer program that will
JFP1 3 6 9 12 PWRSW RESET lead you through the installation of various device drivers
SNMP
needed to take full advantage of your motherboard.
& 2(+) 5(-) 8 11 HDDLED SM_BUS
The computer is supplied with a battery-powered realtime
JFP2 1(+) 4 7 10(-) SPEAKER clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
JFP3 1(+) 2 3(-) 4 5 PWRLED & KEYLOCK
type recommended by the manufacturer. Discard used
batteries according to manufacturer’s instructions.
JFP1, JFP2

Pin.3 #PWR_SW Declaration of Conformity

Pin.6 GND
The device complies with the requirements in Part 15 of
Pin.9 #RST_SW the FCC rules. Operation is subject to the following two
conditions:
Pin.12 GND
1. This device may not cause harmful interference;
Pin.8, Pin.11 HWM_SMB_DATA, HWM_SMB_CLK 2. This device must accept any interference received,
including interference that may cause undesired
*Power button pin is located in Pin 3 & 6 of front panel
operation.
connector.

Board Layout

LAN2_USB3_4
PCIEX16 PCIEX4 PCIEX16 PCIEX4 PCIEX8
IPMI Module _Slot 4 _Slot 5 _Slot 6 _Slot 7 _Slot 9 SYSFAN5 LAN3_4
LAN1_USB1_2

COM2 VGA1_COM1
SYSFAN6 SYSFAN4
SYSFAN7
DIMMG1
PCIEX4_SLOT3
PCIEX16_SLOT2 DIMMH1
PCIEX4_SLOT1 DIMMI1
BH2
PCIEX16_Slot 8
KBMS1
GPIO1
SPI_SKT1 DIMMJ1
SMBUS1 DIMMK1
SSATA0_1 DIMML1
SSATA2_3
SP1_CN1
LPC1
JME
JCOMS1
SSATA4
SATA0_1
VROC1
SATA2_3
VOLT1 PMBUS1
SATA4_5
CPUFAN1
SATA6_7 SSATA5
JWDT1 ATX12V2 SGPIO2
USB9_10
USB11 ATXPWR1 SGPIO1
SYS_LED1 DIMMC1
JTHR_SEL1
SLOT12V1 DIMMB1
USB7_8 DIMMA1
SYSFAN0
EX_THR1
SYSFAN1 ATX12V1 DIMMF_E_D
SYSFAN2 SYSFAN3 CPUFAN0 JFP1_JFP2 JFP3 USB5_6 HDAUD1

Figure 1: Board Layout: Jumper and Connector Locations

ASMB-975 Startup Manual 3