PROJECT :

UPGRADATION OF PARBHANI-GANGAKHED SECTION OF NATIONAL

HIGHWAY-752K (39.375 KM) IN THE STATE OF MAHARASHTRA ON EPC MODE

CLIENT :

MINISTRY OF ROAD TRANSPORT AND HIGHWAYS

EPC Contractor:
SARJAN INFRACON PVT. LTD.

Authority Engineer

EDMAC, Engineering Consultant, New Delhi

Design Consultant :
INFRA DESIGN STUDIO PVT. LTD.
Plot No. DX-10, TTC Industrial Area, MIDC, Shiravane, Nerul,
Navi Mumbai- 400706 Tel: +91 22 6505 0800

TITLE :

Design of Minor Bridge at Ch 35+360 (Box 3 x 4.50 x 4.35 )

DESIGN DOCUMENT NO. REVISION NO.

IDSPL/PAR-GAN/MNB/35+360/09 R1

REV. PREPARED CHECKED

DATE PURPOSE OF ISSUE
NO. INITIAL SIGN INITIAL SIGN
9-Apr-19 00 Original Submission MIS/ APB SPB

12-Apr-19 01 Revision for IRC SP 115:2018 MIS/ APB SPB

 CONTENT

SR. NO. DESCRIPTION

Introduction
1 Data:

2 Calculation of loads:
3 Modulus of subgrade reaction
4 Check for base pressure

5 Load Combination
6 Summary of Moments
Raft Slab Design
7 Ultimate Bending Check for Bottom slab (Raft)
8 Serviceability Limit State Check for Stress at bottom slab (raft)
9 Serviceability Limit State Check for Crack Width (Raft)
10 ULS Shear Check for Bottom Slab
Top Slab Design
11 Ultimate Bending Check for Top slab
12 Serviceability Limit State Check for Stress at Top slab
13 Serviceability Limit State Check for Crack Width (Top slab )
14 ULS Shear Check for Top Slab
Wall Design
15 Ultimate Bending Check for Outer & Inner wall
16 Serviceability Limit State Check for Stress for Outer & Inner wall
17 Serviceability Limit State Check for Crack Width for Outer & Inner wall
18 ULS Shear Check for Top Slab

19 STAAD Input & OUTPUT

 Introduction
The following design note presents the design note for RCC box structure having width as 16 m, clear span as 4.5 m
and clear height as 4.35 m with skew angle 0 degree.

The analysis of box structure has been done considering a slice of unit width for all Dead Loads while box structure
with 12m width is considered for obtaining live load. The box has been analysed for its self weight, superimposed dead
load ( due to wearing coat and guard stone ) and earth pressure using STAAD.Pro. Spring Supports are used in the
design. Spring constant is calculated on the basis of modulus of subgrade reaction of the soil. Cases of earth pressure
for Dry condition is considered . Earth pressure at rest with dry density of earth is considered to produce maximum
earth pressure is considered to produce active earth pressure.

1 Data:

Overall width of Structure for Live load analyis = 16 m

Width of Crash Barrier = 0.5 m
Width of footpath = 1.5 m
Height of kerb = 0 m
Width of railing = 0 m
Width of box = 16.00 m
No. of Cells = 3
Clear Span of the box L = 4.50 m 5.00
Skew Angle = 0.00 deg
Height of overburden = 0.00 m
Thickness of Top slab a = 450.00 mm
Thickness of Raft b = 500.00 mm
Thickness of Outer Web c = 500.00 mm
Thickness of Inner Web d = 400.00 mm
Thickness of wearing coat over top slab = 75 mm
Thickness of crust over Raft = 0.00
Clear Span of end cell = 4.50 m
Clear Span of Intermediate cell = 4.50 m
Clear height of the box H = 4.35 m
Effective height of the box = 4.83 m
Skew width = 16.00 m
Skew span of end cell = 4.50 m
Skew span of intermmediate cell = 4.50 m
Effective span of the end Cell = 5 m
Effective span of the intermmediate cell = 5 m
Size of Haunches in Web = 0.1 x 0.3 m
150 2
SBC of Soil = kN/m

Materails used
Grade of Concrete = M 30
Garde of Steel = Fe 500

Unit Weights and Density

Unit Weight of Concrete = 25 kN/m3
Unit Weight of Wearing Coat 23 kN/m3
Dry Density of Earth = 20 kN/m3
Saturated Density of Earth = 20 kN/m3
Submerged Density of Earth = 10 kN/m3

Page 1
 Clear covers
Top slab Inner face = 40 mm
Outer Face = 75 mm
Bottom slab Inner face = 75 mm
Outer Face = 75 mm
Web Inner face = 40 mm
Outer Face = 75 mm

Reference Codes
IRC 6: 2014
IRC112: 2011

TOP SLAB

OUTER WALL
OUTER WALL

INNER WALL
INNER WALL

c H
d

RAFT SLAB
b

Figure Showing dimensions of the box

2 Calculation of loads:

2.1 Dead load

Top Slab = 15.3 x 0.5 x 25 = 172 kN/m

Bottom Slab = 15.3 x 0.5 x 25 = 191 kN/m
Outer Webs = 2.0 x 4.4 x 0.50 x 25 = 109 kN/m
Inner Webs = 2.0 x 4.4 x 0.40 x 25 = 87 kN/m
Haunches = 12 x 0.1 x 0.15 x 25 = 4.5 kN/m
Weight of Overburden = 0.00 x 20 = 0 kN/m

Total Weight = 562 kN/m

2.2 Superimposed Dead Load (SIDL)

Wearing coat over top slab = 23.0 x 0.075 = 1.725 kN/m2

Wearing coat over Raft (RCC) = 25.0 x 0.00 = 0 kN/m2
2.3 Earth pressure
Earth Pressure at Active State
Saturated Condition :
As per Coulomb's theory, Coefficient of Active Earth Pressure,

SIN2(a+f)
Ka = 2
SIN(f+d) SIN(f-i)
SIN2(a) SIN(a-d) 1+
SIN(a-d) SIN(a+i )

0.750
x 0.940 0.408 2
1 1+

Page 2
Angle of internal friction of soil f = 30 o 0.524 Radian
Angle of incli of stem at back a = 90 o 1.571 Radian
Angle of wall friction d = 20 o 0.349 Radian
Angle of inclination of back fill soil i = 0.00 o 0.000 Radian
Coefficient of Active earth pressure ka = 0.2973

Coefficient of horz.active earth pressure Kah for straight face of stem = 0.2794
Dry Density of Earth = 20 kN/m3

Earth Pressure at
H= 0.225 m, at C/L of Top Slab = 0.279 x 20 x 0.23 = 1.26 kN/m2
5.05 m, at C/L of Bottom Slab = 0.279 x 20 x 5.05 = 28.22 kN/m2

LL Surcharge Pressure ( 1.2m height of Earth ) = 0.279 x 20 x 1.2 = 6.71 kN/m2

As per IRC SP 115 : 2018 Cl 6.4.2 Active earth pressure may be ignored
As per IRC SP 115 : 2018 Cl 6.4.4
When the bridge expand due to rise in temperature, the intensity of earth pressure behind the abutment
depends on the magnitude of the bridge displacement towards the backfill soil.
The actual earth pressure coefficient may change between at rest k0 and passive pressure kp
depending upon the amount of displacement of abutment .
also as per clause 6.4.5 live load surcharge shall be ignore in this case

Passive earth pressure

Sin2(a-f)
Kp  2
 Sin(f +d) Sin(f +i) 
Sin2aSin(a+d) 1- 
 Sin(a+d) Sin(a+i) 

Kp = 6.1054

d thermal displacement at top of abutment

L 7500 mm
t= 17.5 oC
a 0
d= atl = 1.575 mm

H 4.35
k* = (d/0.05H)^0.4*Kp
0.8504 > K0 = 0.50

Earth Pressure at
H= 0.225 m, at C/L of Top Slab = 0.850 x 20 x 0.23 = 3.83 kN/m2
5.05 m, at C/L of Bottom Slab = 0.850 x 20 x 5.05 = 85.89 kN/m2

Earth Pressure at Rest State

Since the side walls are effectively restrained against movement, At rest earth pressure is considered for design.
Saturated Condition :
Coefficient of Earth pressure at rest K0 = 1 - SIN(f)
1 - 0.5
Coefficient of Earth Pressure at rest = 0.50
Dry Density of Earth = 20 kN/m3

Earth Pressure at

Page 3
 H= 0.225 m, at C/L of Top Slab = 0.500 x 20 x 0.23 = 2.25 kN/m2
5.05 m, at C/L of Bottom Slab = 0.500 x 20 x 5.1 = 50.50 kN/m2

LL Surcharge Pressure ( 1.2m height of Earth ) = 0.500 x 20 x 1.2 = 12.00 kN/m2

2.3 Water Pressure

Density of water = 10 kN/m3

Water Pressure at
H= 0 m, at C/L of Top Slab = 10 x 0.00 = 0.00 kN/m2
4.25 m, at end of Bottom Haunch p1 = 10 x 4.25 = 42.50 kN/m2

2.4 Temperature Effect

F = Ec α ∆ t A

Ecm = Modulus of Elasticity of Concrete = 3.10E+07 kN/m2

Ecm for Temp. calculations = 1.55E+07 kN/m2
α = Coefficient of Thermal Expansion = 1.20E-05 / oC ( As per IRC - 6 : 2014 )
∆ t = Temperature Differential
A = X - Sectional Area of section where temperature differential is Dt

Page 4
a. Temperature Raising Gradient

h = 0.45 m

4 13.8

0.14 1 2

3
0.14

0.05

4
0.14
2.1

Force Acting at Eccentri Moment

S.No. ∆t b h A=bxh
F ( kN ) (m) city, (m) (kN-m)
1 4 1 0.135 0.135 100.44 0.0675 0.1575 15.8193
2 13.8 1 0.135 0.0675 173.259 0.045 0.18 31.1866
3 4 1 0.135 0.0675 50.22 0.18 0.045 2.2599
4 2.1 1 0.135 0.0675 26.3655 0.405 -0.18 -4.74579
Total 350.28 44.52

b. Temperature Falling Gradient

h = 0.5 m

9.9 0.7

2 1
0.1

3
0.113

0.05

6 0.113

5 0.09
5.8 4 0.8

Page 5
 Force Acting at Eccentri Moment
S.No. ∆t b h A=bxh
F ( kN ) (m) city, (m) (kN-m)
1 0.7 1 0.1 0.09 11.718 0.045 0.18 2.10924
2 9.9 1 0.1 0.045 82.863 0.03 0.195 16.1583
3 0.7 1 0.113 0.05625 7.32375 0.1275 0.0975 0.71407
4 5.8 1 0.09 0.045 48.546 0.3225 -0.0975 -4.73324
5 0.8 1 0.09 0.09 13.392 0.405 -0.18 -2.41056
6 0.8 1 0.113 0.05625 8.37 0.42 -0.195 -1.63215
Total 172.213 10.206

c. Uniform Temperature
( As per Clause - 218.2, IRC:6 - 2014 )

Maximum Shade Air Temperature = 45 degree

Minimum Shade Air Temperature = 3 degree

Difference between Maximum & Minimum Air Shade Temperature = 42 degree

So, the Bridge Temperature at the time of restraint = 34 degree

( say ) 35 degree

Therefore, Load effect due to Temperature Rise & Temperature Fall = ( +/- ) 35 degree
( E value is considered 50% )
Note: Rather than taking 50%E, loads are reduced by 50%

Therefore, Load effect due to Temperature Rise & Temperature Fall = ( +/- ) 17.5 degree

Shrinkage strain for Deck slab 0 to 30 days = 0.0002

Temp for shrinkage = 0.0002 / 0.000012 = 16.67 degree

2.5 Live loads

Class A loading, Class 70R Wheeled loading, Class 70R tracked loading are applied on the structure. Increment of
0.5m is given to the loads and effective widths are calculated. From the STAAD model, only critical cases are
considered and the corresponding live loads are applied on the structure along with all the other loads.

5 6 7 8

11
13

10

12
9

1 2 3 4

Figure of Box Showing Sections

Figure showing Staad model of box structure with spring support and constraints.

Load 1

Page 6
2.6 Braking Force

Width of Carriageway = 16.00 m

No. of lanes to be considered = This is 4 lane as per IRC : 6 - 2014

Arrangement of Vehicles =
4 lanes of class A or 2 lanes of 70R or 2 lanes of class A + 1 lane of 70R

As per Clause - 211.2, IRC - 6 : 2014 , the braking force shall be 20% for the first two lanes plus 5% for the lanes in
excess of two.

a. 1 lanes of Class 70RT + 2 Lane of Class A

Force due to 70 RT = 0.2 x ( 1000 ) = 200.0 kN

= 0.05 x ( 500 ) = 25.0 kN

Total Load = 225.0 kN

Total Width = 16.00 m

Braking force = 225 / 16.0 = 14.06 kN/m

Moment due to braking = 21.094 kN-m /m

b. 1 lane of Class 70RW + 1 Lane of Class A

Force due to 70 RT = 0.2 x 1000 = 200.0 kN

= 0.05 x 500 = 25.0 kN

Total Load = 225.0 kN

Total Width = 16 m

Braking force = 225 / 16.0 = 14.063 kN/m

Moment due to braking = 21.094 kN-m /m

c. 3 lanes of Class A

Force due to CLASS A = 0.2 x 500 = 100.0 kN

= 0.05 x 1000 = 50.0 kN

Total Load = 150.0 kN

Total Width = 16 m

Braking force = 150 / 16.0 = 9.38 kN/m

Moment due to braking = 14.063 kN-m /m

d. 1 lanes of Class 70 RW

Force due to 70 RT = 0.2 x 1000 = 200.0 kN

= 0.00 x 1000 = 0.0 kN

Total Load = 200.0 kN

Page 7
 Total Width = 16 m

Braking force = 200 / 16.0 = 12.50 kN/m

Moment due to braking = 16.903 kN-m /m

Max braking force = 14.06 kN/m

Braking moment = 21.1 kN-m /m

3 Modulus of subgrade reaction

Allowable Safe Bearing = 150.00 kN/m2

Factor of Safety (S.F) = 2.5
Modulus of Subgrade reaction (Ks=40*S.F.*qa ) (kN/m2) = 15000 kN/m3

Modulus of sub grade Reaction for 0.3 x 0.3 Plate = 2800 T/cu.m
Reduction for width is given by Ks x [ (B + B1) /(2 x B) ]^2
B = 16.00 m
B1 = 0.3 m

Ks ' = 2800 * ( ( 16 + 0.3 ) / ( 2 * 16 ) ) ^ 2 = 726 T/cu.m

Reduction for Length is given by Ks' x [ (m + 0.5 ) / 1.5 m ]

L = 14.00 m
B = 16.00 m

m = L /B = 14 /16 = 0.88

Ks '' = 726 * ( ( 0.88 + 0.5 ) / ( 1.5 * 0.88 )) = 759 T/cu.m

Use ks = 750 T/cu.m in design

4 Check for base pressure

SBC of soil = 150 kN/m2

Summation of reactions at supports = 713 kN LL = 90.9 kN /m

Moment due to unequal reactions on left and right of raft from the center of raft = 357 kN.m
Area of raft = 1 x 14.80 = 14.8 m2
Section modulus = 1 x 14.8 x 14.8 / 6 = 36.51 m3

Base pressure = P M
+
A Z
= 804 357
+
14.8 36.5
= 64 kN/m2 < 150 kN/m2 Safe

Page 8
 5 Check for Stability (For Submerged Condition)

5.1 Dead load

Top Slab = 1 x 16.0 x 0.45 x 15.3 x 15 = 1647 kN

Bottom Slab = 1 x 16.0 x 0.50 x 15.3 x 15 = 1830 kN
Outer Webs = 2 x 4.35 x 0.50 x 16.0 x 15 = 1044 kN
Inner Webs = 2 x 4.35 x 0.50 x 16.0 x 15 = 1044 kN
Haunches = 12 x 0.10 x 0.15 x 16.0 x 15 = 43 kN

Total Weight = = 5608 kN

5.2 Superimposed Dead Load (SIDL)

Wearing coat over top slab= 16.0 x 0.08 x 15.3 x 13.0 = 238 kN

5.3 Water pressure

5.3.1 Horizontal Forces due to Water current on vertical wall

P = 52 x K x V2
P = Intensity of pressure due to water current
V = The velocity of the current at the point where the pressure Intensity is being calculated = 6.36 m/s
Klong = Constant having the values for different shapes of piers 1.50
Ktrans = Constant having the values for different shapes of piers 0.66

Plong = = 52 x 1.50 x 6.36 x 6.36 = 30.96 kN/m2

Ptrans = = 52 x 0.66 x 6.36 x 6.36 = 13.62 kN/m2

HFL = 100.00 m
Raft Top = 95.20 m

Force due to water current

Water Force Moment Moment

Skew Force (Long.)
Pressure (Trans.) (Trans) (Long.)
(degree) (kN) (kN) (kN-m) (kN) (kN-m)
0 30.96 71.10 227.54 0.00 0.00
20 30.96 62.79 200.92 9.45 30.25

5.3.2 Water force on structure

Clause 7.11.2 IRC SP 82: 2008

a.) Pressure Due to Static Load, p1 = ω x h

ω= 1 T/m3 = 10 kN/m3
h= Afflux or depth of superstructre which ever is higher
= 0.45 m or 0.40 m
= 0.45 m

p1 = 0.45 x 10 = 4.5 kN/m2

Total force on Superstructure = 1/2 x 4.50 x 0.45 x 15.3

= 15 kN

Page 9
Lever arm for this force = 4.28
Transverse moment due to this force = 66 kN.m

Total Pressure on wall = 4.50 x 0.40 x 4.35 x 8

= 63 kN
Lever arm for this force = 2.18
Tranverse moment = 136 kN.m

b.) Pressure due to Velocity Head

p2 = 52 x k x V2 30.96
0.45 0.17
k= 1.5 4.80
V= 6.36 m/s

p2 = 31 kN/m2
p2' = 4.80 kN/m2 4.80 4.63

Water Force Moment Force Moment

Skew
Pressure (Trans.) (Trans) (Long.) (Long.)
(degree) (kN) (kN) (kN-m) (kN) (kN-m)
0 36.21 167.63 0.000 0.00
20 31.970 148.02 4.235 19.61

c.) Pressure due to Eddies

p3 = ω x (Vv - V)^2 / (2 g)
ω= 1 T/m3 = 10 kN/m3
Vv = 2.76 m/s
V= 4.5 m/s
2
g= 9.81 m/s

p3 = = 1 x (4.35 -4.5)^2 / (2 x9.81)

= 0.001 T/m2
= 0.01 kN/m2
Force on superstructure = 0.08 kN
Trans moment = 0 kN.m

d.) Pressure due to Friction

2
p4 = f x ρ x ( C x Vv)
ρ= ω/g= 0.10
f= 1.0
C= 0.1
Vv = 2.76 m/s

p4 = 0.0078 T/m2
= 0.0777 kN/m2

Page 10
Friction force against slab = 0.1 x 18 x 16.00 = 22.4 kN
Lever arm for this force = 4.28 m
MT due to this force = 96 kN.m

Friction force against pier = 0.08 ( x ( 0.50 x 4.35 )+( 4.35 x 16.0 )) x8= 45 kN

Lever arm for this force = 2.18 m

MT due to this force = 97 kN.m

e.) Force due to uplift head under super structure.

Uplift Force = ω x h x Asp
ω= 1 T/m =3
10.0 kN/m3
h = Afflux or (Th. of Super Structure - Head loss due to increase in Velocity)
which ever is higher.
h = 0.5 m
Asp = Area of Super structure

Uplift Force = 10 x 0.45 x 18.0 x 16.0

= 1296 kN acting upward

SUMMARY OF FORCES AND MOMENTS

SUBMERGED CONDITION
LOAD P (kN.) ML (kN.m) MT (kN.m) FL (kN.) FT (kN.)
DL 5608 0 0 0 0
Wearing Coat 238 0 0 0 0
Water Current -1296 50 629 14 346
Live Load 1550 21 0 0

LOAD COMBINATIONS (WORKING STRESS METHOD) FOR BASE PRESSURE

Sr. No. LOAD COMBINATION P (kN) ML (kN-m) MT(kN-m)
1 DL+WC+Water Current+ll 4550 71 629

5.4. Check for Base Pressure (WSM)

Plan area of footing at base
A = 16.0 x 15.3 = 244.00 m2

ZL = 16 x 15.3 x 15.3 = 620.17 m3

6
ZT = 16 x 16.0 x 15.3 = 650.67 m3
6
Base pressure at all four nodes of footing due to various load combinations is calculated.
Base pressure
P= ML MT
I+

I+

A ZL ZT
BASE PRESSURE AT
Sr. LOAD
P (T) ML (T-m) MT (T-m) 1 2 3 4
No. COMBINATION
T/m2 T/m2 T/m2 T/m2
1 DL+WC+Water Current+ll 464 7.2 64.1 2.011 1.988 1.791 1.814

5.5. Check for Sliding (WSM)

Dead Load = 4550 kN (Stabilizing force)
Water Pressure = 346 kN (Destabilizing force)

FOS = 0.5 x 4550 = 6.6 > 1.5

346

Page 11
 Summary Forces used is Staad (Without moving load)

1 Self Weigth calculated using following thicknes

Thickness of Slab = 450 mm
Thickness of Raft = 500 mm
Thickness of End wall = 500 mm
Thickness of Interior wall = 400 mm

2 Superimposed Dead Load (SIDL) = 1.725 kN/m2

3 Crash Barrier + Service load = 10.00 kN/m

5 Braking Force = 14.06 kN/m

6 Earth Pressure at Active State = 3.83 kN/m2

at Bottome of slab 85.89
7 Active LL Surcharge Pressure = 0 kN/m2

8 Earth Pressure at Rest State = 2.25 kN/m2

at Bottome of slab 50.50
9 Static LL Surcharge Pressure = 12.00 kN/m2

10 Temperature Effect
a Temperature Raising Gradient
Force = 350.3 kN/m2
Moment = 44.5 kN/m2

b Temperature Falling Gradient

Force = 172.21 kN/m2
Moment = 10.21 kN/m2

c Uniform Temperature fall / rise = 17.5 degree

d Shrinkage of deck slab = 16.67 degree
In Staad only Temperature raising Gradient is considered as it is critical

Base Pressure (Per meter width)

1 Total Dead load of Box = 562 kN/m

2 Superimposed Dead Load (SIDL) = 25.875 kN/m

3 Total Live Load = 125.00 kN/m

4 Maximum Base in Raft (Dry) = 64.11 kN/m2

Summary 12
 SUMMARY OF DEAD LOAD BM (T-m)
ULS DL BM SLS DL BM QP BM
Component Location
NO LL LL (Acc) LL (Lead) NO LL LL (Acc) LL (Lead) NO LL
End Support 5.78 9.94 16.47 3.72 6.2 6.2 10.56
DECK End Span 2.17 5.62 7.26 1.69 3.64 3.64 3.76
SLAB Int Support 5.76 7.59 10.6 4.12 5.3 5.3 5.69
Int Span 2.15 3.72 4.45 1.48 2.53 2.53 3.3

End Support 12.88 18.68 7.42 8.87 12.72 12.72 4.74

RAFT End Span 4.86 8.03 4.61 3.62 5.4 5.4 2.59
SLAB Int Support 7.87 11.49 7.42 5.65 8.05 8.05 3.7
Int Span 4.3 4.85 3.15 3.11 3.48 3.48 1.99
End Wall Bottom 10.91 15.94 14.36 7.7 11.04 11.04 8.79
END
End Wall Mid 9.85 11.89 8.53 6.41 7.3 7.3 6.82
WALL
End Wall Top 4.69 8.39 6.88 3.06 5.45 5.45 4.04
INT Int Wall Bottom 5.27 8.56 8.07 3.58 5.76 5.76 2.65
WALL Int Wall Top 3.91 6.74 6.36 2.72 4.59 4.59 1.92

SUMMARY OF DL + LL BM (T-m)
LOAD COMBINATIONS FOR VERIFICATION 0F STRUCTURAL STRENGTH (ULS)
ULS DL BM ULS LL BM ULS BM (DL + LL)
Location
NO LL LL (Acc) LL (Lead) LL (Acc) LL (Lead) NO LL LL (Acc) LL (Lead) GOVERN
End Support 5.780 9.940 16.470 5.551 7.241 5.780 15.491 23.711 23.711
End Span 2.170 5.620 7.260 8.018 10.458 2.170 13.638 17.718 17.718
Int Support 5.760 7.590 10.600 8.892 11.598 5.760 16.482 22.198 22.198
Int Span 2.150 3.720 4.450 7.723 10.074 2.150 11.443 14.524 14.524

End Support 12.880 18.680 7.420 6.533 8.522 12.880 25.213 15.942 25.213
End Span 4.860 8.030 4.610 4.725 6.164 4.860 12.755 10.774 12.755
Int Support 7.870 11.490 7.420 8.273 10.791 7.870 19.763 18.211 19.763
Int Span 4.300 4.850 3.150 2.358 3.075 4.300 7.208 6.225 7.208

End Wall Bottom 10.910 15.940 14.360 6.489 8.465 10.910 22.429 22.825 22.825
End Wall Mid 9.850 11.890 8.530 -3.590 -4.683 9.850 8.300 3.847 9.850
End Wall Top 4.690 8.390 6.880 5.356 6.986 4.690 13.746 13.866 13.866
Int Wall Bottom 5.270 8.560 8.070 3.307 4.314 5.270 11.867 12.384 12.384
Int Wall Top 3.910 6.740 6.360 4.106 5.355 3.910 10.846 11.715 11.715

LOAD COMBINATIONS FOR VERIFICATION 0F SERVICEABILITY LIMIT STATE (SLS)

SLS DL BM SLS LL BM SLS BM (DL + LL)
Location
NO LL LL (Acc) LL (Lead) LL(Acc) LL(Lead) NO LL LL (Acc) LL (Lead) GOVERN
End Support 3.720 6.200 6.200 3.620 4.827 3.720 9.820 11.027 11.027
End Span 1.690 3.640 3.640 5.229 6.972 1.690 8.869 10.612 10.612
Int Support 4.120 5.300 5.300 5.799 7.732 4.120 11.099 13.032 13.032
Int Span 1.480 2.530 2.530 5.037 6.716 1.480 7.567 9.246 9.246

End Support 8.870 12.720 12.720 4.261 5.681 8.870 16.981 18.401 18.401
End Span 3.620 5.400 5.400 3.082 4.109 3.620 8.482 9.509 9.509
Int Support 5.650 8.050 8.050 5.396 7.194 5.650 13.446 15.244 15.244
Int Span 3.110 3.480 3.480 1.538 2.050 3.110 5.018 5.530 5.530

End Wall Bottom 7.700 11.040 11.040 4.232 5.643 7.700 15.272 16.683 16.683
End Wall Mid 6.410 7.300 7.300 2.342 3.122 6.410 9.642 10.422 10.422
End Wall Top 3.060 5.450 5.450 3.493 4.657 3.060 8.943 10.107 10.107

Int Wall Bottom 3.580 5.760 5.760 2.157 2.876 3.580 7.917 8.636 8.636
Int Wall Top 2.720 4.590 4.590 2.678 3.570 2.720 7.268 8.160 8.160

SUMMERY_MOM 13
Critical SF at Section D from face of Raft / Slab / Wall ( T )
Location ULS DL SF ULS LL SF ULS DL + LL SF GOVERN
NO LL LL (Acc) LL (Lead) LL (Acc) LL (Lead) LL (Acc) LL (Lead)
RAFT 8.25 8.99 8.43 4.302 5.612 13.292 14.042 14.042
SLAB 3.64 4.14 3.35 9.641 7.391 13.781 10.741 13.781
WALL 14.82 17.12 13.87 1.659 2.165 18.779 16.035 18.779

SUIMMARY OF BM FOR RCC DESIGN (KN-m)

Component Location ULS SLS (RC) SLS (QPC)
End Support 23.711 11.027 10.560
DECK End Span 17.718 10.612 3.760
SLAB Int Support 22.198 13.032 5.690
Int Span 14.524 9.246 3.300
End Support 25.213 18.401 4.740
RAFT End Span 12.755 9.509 2.590
SLAB Int Support 19.763 15.244 3.700
Int Span 7.208 5.530 1.990

End Wall Bottom 22.825 16.683 8.790

END
End Wall Mid 9.850 10.422 6.820
WALL
End Wall Top 13.866 10.107 4.040
INT Int Wall Bottom 12.384 8.636 2.650
WALL Int Wall Top 11.715 8.160 1.920

5 6 7 8

11
13

10

12
9

1 2 3 4

SUMMERY_MOM 14
 7 Ultimate Bending Check for Bottom slab (Raft)

Moment fck fyk fctm fcd Cover Width, Es Xlim

Location d (mm) β1 β2 Єyd Єcu x (mm) Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) (MPa) (mm)
Section 1 252.132 30 500 2.501 13.4 75 1000 519 0.8095 0.41597 200000 0.0022 0.0035 46.519 320.15 OK > than x
Section 2 127.554 30 500 2.501 13.4 40 1000 454 0.8095 0.41597 200000 0.0022 0.0035 26.546 280.05 OK > than x
Section 3 197.631 30 500 2.501 13.4 75 1000 519 0.8095 0.41597 200000 0.0022 0.0035 36.151 320.15 OK > than x
Section 4 72.075 30 500 2.501 13.4 40 1000 454 0.8095 0.41597 200000 0.0022 0.0035 14.837 280.05 OK > than x

Lever Ast Provided (mm2/m) Total Ast

Moment Ast min Ast req.
Location Arm, Ast (mm2/m) 2 2 Bar 1 Spacing 1 Bar 2 Spacing 2 Provied Remark
(kN-m) (mm /m) (mm /m)
z(mm) (mm) (mm) (mm) (mm) (mm2/m) Position
Section 1 499.65 252.13 1160.038 590.346 1160.038 12 200 16 200 1571 OK Bottom
Section 2 442.958 127.55 661.974 590.346 661.974 12 150 0 150 754 OK Top
Section 3 503.962 197.63 901.505 674.867 901.505 12 200 12 200 1131 OK Bottom
Section 4 447.828 72.075 369.985 590.346 590.346 12 150 0 150 754 OK Top

Distribution Steel = 20% of Main Steel = 314 mm2

Provide 8 mm @ 150 mm C/C i.e. 335.103 mm2 OK

8 Serviceability Limit State Check for Stress at bottom slab (raft)

Moment of
Moment fck fyk fctm fcm Cover Width, Depth, Ecm Es σtop = σbottom
Location d (mm) Inertia Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) D (mm) (MPa) (MPa) 4 (N/mm2)
(mm )
Section 1 184.01 30 500 2.501 40 75 1000 519 600 31186.6 200000 1.8E+10 3.067 Section is Cracked
Section 2 95.09 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 2.282 Section is Uncracked
Section 3 152.44 30 500 2.501 40 75 1000 519 600 31186.6 200000 1.8E+10 2.541 Section is Cracked
Section 4 55.3 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 1.327 Section is Uncracked

Total Ast Permissible Permissible Cracked

dc σconcrete σsteel
Location Provied Stress in Stress in Moment of Zc (mm )
3
Zs (mm )
3
Remark Remark
(mm) (N/mm2) (N/mm2)
(mm2/m) concrete Steel Inertia (mm4)
Section 1 1570.796 14.400 300.000 92.678 3.27E+08 3.53E+06 7.67E+05 8.14 OK. 240.00 OK.
Section 2 753.982 14.400 300.000 61.601 1.28E+08 2.08E+06 3.27E+05 7.12 OK. 290.95 OK.
Section 3 1130.973 14.400 300.000 79.817 2.45E+08 3.06E+06 5.57E+05 7.76 OK. 273.74 OK.
Section 4 753.982 14.400 300.000 61.601 1.28E+08 2.08E+06 3.27E+05 4.14 OK. 169.20 OK.

Bottom Slab 15
 9 Serviceability Limit State Check for Crack Width (Raft)

Moment of
Moment fck fyk fctm fcm Cover Width, Depth, Ecm Es σtop = σbottom
Location d (mm) Inertia 2 Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) D (mm) (MPa) (MPa) 4 (N/mm )
(mm )
Section 1 47.4 30 500 2.501 40 75 1000 519 600 31186.6 200000 1.8E+10 0.790 Section is Uncracked
Section 2 25.9 30 500 2.501 40 75 1000 454 500 31186.6 200000 1.042E+10 0.622 Section is Uncracked
Section 3 37 30 500 2.501 40 75 1000 519 600 31186.6 200000 1.8E+10 0.617 Section is Uncracked
Section 4 19.9 30 500 2.501 40 75 1000 454 500 31186.6 200000 1.042E+10 0.478 Section is Uncracked

Total Ast Permissible Permissible Cracked

dc σconcrete σsteel
Location Provied Stress in Stress in Moment of Zc (mm3) Zs (mm3) Remark Remark
(mm) (N/mm2) (N/mm2)
(mm2/m) concrete Steel Inertia (mm4)
Section 1 1570.796 10.800 300.000 92.678 3.27E+08 3.53E+06 7.67E+05 2.10 OK. 61.82 OK.
Section 2 753.982 10.800 300.000 61.601 1.28E+08 2.08E+06 3.27E+05 1.94 OK. 79.25 OK.
Section 3 1130.973 10.800 300.000 79.817 2.45E+08 3.06E+06 5.57E+05 1.88 OK. 66.44 OK.
Section 4 753.982 10.800 300.000 61.601 1.28E+08 2.08E+06 3.27E+05 1.49 OK. 60.89 OK.

Ac,eff Bar Crack Permissible

α= hc,eff Min Designed Sr,max
Location ρp,eff kt k1 k2 Єsm - Єcm Dia. Ф Width W k Crack Width Remark
Es/Ecm (mm) (mm ) 2 (Єsm - Єcm) (Єsm - Єcm) (mm)
(mm) (mm) (mm)
Section 1 6.413 169.11 169107 0.00929 1.0 0.8 0.5 -1.12E-03 0.000185 1.85E-04 14.29 516.45 0.096 0.3 OK.
Section 2 6.413 115 115000 0.00656 1.0 0.8 0.5 -1.59E-03 0.000238 2.38E-04 12.00 566.15 0.135 0.3 OK.
Section 3 6.413 173.39 173394 0.00652 1.0 0.8 0.5 -1.66E-03 0.000199 1.99E-04 12.00 567.76 0.113 0.3 OK.
Section 4 6.413 115 115000 0.00656 1.0 0.8 0.5 -1.68E-03 0.000183 1.83E-04 12.00 566.15 0.103 0.3 OK.

Bottom Slab 16
 10 ULS Shear Check for Bottom Slab

A. Elements Not requiring design shear reinforcement.

Cover = 75 mm
D = 500 mm
d = 500 - 75 - 12 /2 = 419.0 mm
bw = 1000 mm
fck = M 30 MPa
fyk = Fe 500 MPa
K = 1 + sqrt (200 / d )= 1.691 Eq. 10.2, Pg.88
Asl = Tensile reinforcement.
= 1571
ρl = Minimum of i.) Asl / (bw x d) = 0.0037
ii.) 0.02
= 0.0037
NEd = Axial force in the cross section from the loading or from prestressing
= 0
Ac = bw x d = 419000 mm2
σcp = NEd / Ac < 0.2 x fcd
σcp = 0
VEd = Design shear force at a cross section resulting from external loading and that
due to prestressing
= 140.415 kN

VRd.c = Maximum of

i.) [ 0.12 x K x (80 x ρl x fck)(1/3) + 0.15 x σcp] x bw x d Eq. 10.1, Pg.88

= 176827.286 N
= 176.83 kN

(3/2) (1/2)
ii.) [0.031 x K x fck + 0.15 x σcp] x bw x d Eq. 10.3, Pg.88
= 156425.954 N
= 156.43 kN

VRd.c = 176.83 kN > VEd

Shear Reinforcement is not required.

Bottom Slab 17
 11 Ultimate Bending Check for Top slab

Moment fck fyk fctm fcd Cover Width, Es Xlim

Location d (mm) β1 β2 Єyd Єcu x (mm) Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) (MPa) (mm)
Section 5 237.11 30 500 2.501 13.4 40 1000 554 0.8095 0.41597 200000 0.0022 0.0035 40.698 341.74 OK > than x
Section 6 177.18 30 500 2.501 13.4 40 1000 454 0.8095 0.41597 200000 0.0022 0.0035 37.248 280.05 OK > than x
Section 7 221.98 30 500 2.501 13.4 40 1000 554 0.8095 0.41597 200000 0.0022 0.0035 38.023 341.74 OK > than x
Section 8 145.24 30 500 2.501 13.4 40 1000 454 0.8095 0.41597 200000 0.0022 0.0035 30.335 280.05 OK > than x

Lever Ast Provided (mm2/m) Total Ast

Moment Ast min Ast req.
Location Arm, Ast (mm2/m) 2 2 Bar 1 Spacing 1 Bar 2 Spacing 2 Provied Remark
(kN-m) (mm /m) (mm /m)
z(mm) (mm) (mm) (mm) (mm) (mm2/m) Position
Section 5 537.071 237.11 1014.892 590.346 1014.892 12 200 12 200 1131 OK Top
Section 6 438.506 177.18 928.860 590.346 928.860 12 100 0 100 1131 OK Bottom
Section 7 538.183 221.98 948.188 720.378 948.188 12 200 12 200 1131 OK Top
Section 8 441.382 145.24 756.454 590.346 756.454 12 100 0 100 1131 OK Bottom

Distribution Steel = 20% of Main Steel = 226 mm2

Provide 8 mm @ 200 mm C/C i.e. 251.327 mm2 OK

12 Serviceability Limit State Check for Stress at Top slab

Moment of
Moment fck fyk fctm fcm Cover Width, Depth, Ecm Es σtop = σbottom
Location d (mm) Inertia Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) D (mm) (MPa) (MPa) 4 (N/mm2)
(mm )
Section 5 110.27 30 500 2.501 40 40 1000 554 600 31186.6 200000 1.8E+10 1.838 Section is Uncracked
Section 6 106.12 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 2.547 Section is Cracked
Section 7 130.32 30 500 2.501 40 40 1000 554 600 31186.6 200000 1.8E+10 2.172 Section is Uncracked
Section 8 92.46 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 2.219 Section is Uncracked

Total Ast Permissible Permissible Cracked

dc σconcrete σsteel
Location Provied Stress in Stress in Moment of Zc (mm )
3
Zs (mm )
3
Remark Remark
(mm) (N/mm2) (N/mm2)
(mm2/m) concrete Steel Inertia (mm4)
Section 5 1130.973 14.400 300.000 82.685 2.81E+08 3.39E+06 5.95E+05 5.07 OK. 185.21 OK.
Section 6 1130.973 14.400 300.000 74.223 1.84E+08 2.48E+06 4.85E+05 6.66 OK. 218.59 OK.
Section 7 1130.973 14.400 300.000 82.685 2.81E+08 3.39E+06 5.95E+05 5.99 OK. 218.88 OK.
Section 8 1130.973 14.400 300.000 74.223 1.84E+08 2.48E+06 4.85E+05 5.80 OK. 190.45 OK.

Top Slab Page 18

 13 Serviceability Limit State Check for Crack Width (Top slab )

Moment of
Moment fck fyk fctm fcm Cover Width, Depth, Ecm Es σtop = σbottom
Location d (mm) Inertia 2 Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) D (mm) (MPa) (MPa) 4 (N/mm )
(mm )
Section 5 105.6 30 500 2.501 40 40 1000 554 600 31186.6 200000 1.8E+10 1.760 Section is Uncracked
Section 6 37.6 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 0.902 Section is Uncracked
Section 7 56.9 30 500 2.501 40 40 1000 554 600 31186.6 200000 1.8E+10 0.948 Section is Uncracked
Section 8 33 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 0.792 Section is Uncracked

Total Ast Permissible Permissible Cracked

dc σconcrete σsteel
Location Provied Stress in Stress in Moment of Zc (mm3) Zs (mm3) Remark Remark
(mm) (N/mm2) (N/mm2)
(mm2/m) concrete Steel Inertia (mm4)
Section 5 1130.973 10.800 300.000 82.685 2.81E+08 3.39E+06 5.95E+05 4.85 OK. 177.36 OK.
Section 6 1130.973 10.800 300.000 74.223 1.84E+08 2.48E+06 4.85E+05 2.36 OK. 77.45 OK.
Section 7 1130.973 10.800 300.000 82.685 2.81E+08 3.39E+06 5.95E+05 2.61 OK. 95.57 OK.
Section 8 1130.973 10.800 300.000 74.223 1.84E+08 2.48E+06 4.85E+05 2.07 OK. 67.97 OK.

Ac,eff Bar Crack Permissible

α= hc,eff Min Designed Sr,max
Location ρp,eff kt k1 k2 Єsm - Єcm Dia. Ф Width W k Crack Width Remark
Es/Ecm (mm) (mm ) 2 (Єsm - Єcm) (Єsm - Єcm) (mm)
(mm) (mm) (mm)
Section 5 6.413 115 115000 0.00983 1.0 0.8 0.5 -4.65E-04 0.000532 5.32E-04 12.00 343.43 0.183 0.3 OK.
Section 6 6.413 115 115000 0.00983 1.0 0.8 0.5 -9.64E-04 0.000232 2.32E-04 12.00 343.43 0.080 0.3 OK.
Section 7 6.413 115 115000 0.00983 1.0 0.8 0.5 -8.74E-04 0.000287 2.87E-04 12.00 343.43 0.098 0.3 OK.
Section 8 6.413 115 115000 0.00983 1.0 0.8 0.5 -1.01E-03 0.000204 2.04E-04 12.00 343.43 0.070 0.3 OK.

Top Slab Page 19

 14 ULS Shear Check for Top Slab

A. Elements Not requiring design shear reinforcement.

Cover = 40 mm
D = 450 mm
d = 450 - 40 - 12 /2 = 404.0 mm
bw = 1000 mm
fck = M 30 MPa
fyk = Fe 500 MPa
K = 1 + sqrt (200 / d )= 1.704 Eq. 10.2, Pg.88
Asl = Tensile reinforcement.
= 3267.256
ρl = Minimum of i.) Asl / (bw x d) = 0.0081
ii.) 0.02
= 0.0081
NEd = Axial force in the cross section from the loading or from prestressing
= 0
Ac = bw x d = 404000 mm2
σcp = NEd / Ac < 0.2 x fcd
σcp = 0
VEd = Design shear force at a cross section resulting from external loading and that
due to prestressing
= 137.805 kN

VRd.c = Maximum of

i.) [ 0.12 x K x (80 x ρl x fck)(1/3) + 0.15 x σcp] x bw x d Eq. 10.1, Pg.88

= 221956.216 N
= 221.96 kN

(3/2) (1/2)
ii.) [0.031 x K x fck + 0.15 x σcp] x bw x d Eq. 10.3, Pg.88
= 152529.622 N
= 152.53 kN

VRd.c = 221.96 kN > VEd

Shear Reinforcement is not required.

Top Slab Page 20

 14 Ultimate Bending Check for Outer & Inner wall

Moment fck fyk fctm fcd Cover Width,b Es Xlim

Location (mm)
d (mm) β1 β2 Єyd Єcu x (mm) Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) (MPa) (mm)
Section 9 228.25 30 500 2.501 13.4 75 1000 419 0.8095 0.41597 200000 0.0022 0.0035 53.007 258.46 OK > than x
Section 10 148.50 30 500 2.501 13.4 40 1000 454 0.8095 0.41597 200000 0.0022 0.0035 31.036 280.05 OK > than x
Section 11 138.66 30 500 2.501 13.4 75 1000 419 0.8095 0.41597 200000 0.0022 0.0035 31.491 258.46 OK > than x
Section 12 123.84 30 500 2.501 13.4 40 1000 354 0.8095 0.41597 200000 0.0022 0.0035 33.574 218.37 OK > than x
Section 13 117.15 30 500 2.501 13.4 40 1000 354 0.8095 0.41597 200000 0.0022 0.0035 31.687 218.37 OK > than x

Lever Ast Provided (mm2/m) Total Ast

Moment Ast min Ast req.
Location Arm, 2 Provied Remark
(kN-m) Ast (mm /m) (mm2/m) (mm2/m)
Bar 1 Spacing 1 Bar 2 Spacing 2
z(mm) (mm) (mm) (mm) (mm) (mm2/m)
Section 9 396.951 228.25 1322 545 1321.829 12 100 16 200 2136 OK
Section 10 441.09 148.5 774 590 773.945 12 100 0 100 1131 OK
Section 11 405.901 138.66 785 545 785.283 12 100 12 200 1696 OK
Section 12 340.034 123.84 837 460 837.238 12 200 12 200 1131 OK
Section 13 340.819 117.15 790 460 790.186 12 200 12 200 1131 OK

Distribution Steel = 20% of Main Steel = 427 mm2

100 503 2 OK
Provide 8 mm @ mm C/C i.e. mm

15 Serviceability Limit State Check for Stress for Outer & Inner wall

Moment of
Moment fck fyk fctm fcm Cover Width, Depth, Ecm Es σtop = σbottom
Location d (mm) Inertia Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) D (mm) (MPa) (MPa) 4 (N/mm2)
(mm )
Section 9 166.83 30 500 2.501 40 75 1000 419 500 31186.6 200000 1.042E+10 4.004 Section is Cracked
Section 10 104.22 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 2.501 Section is Cracked
Section 11 101.07 30 500 2.501 40 75 1000 419 500 31186.6 200000 1.042E+10 2.426 Section is Uncracked
Section 12 86.36 30 500 2.501 40 40 1000 354 400 31186.6 200000 5.333E+09 3.239 Section is Cracked
Section 13 81.6 30 500 2.501 40 40 1000 354 400 31186.6 200000 5.333E+09 3.060 Section is Cracked

Walls Page 21
 Total Ast Permissible Permissible Cracked
dc σconcrete σsteel
Location Provied Stress in Stress in Moment of Zc (mm3) Zs (mm3) 2 Remark 2 Remark
(mm) (N/mm ) (N/mm )
(mm2/m) concrete Steel Inertia (mm4)
Section 9 2136.283 14.400 300.000 94.32 2.69E+08 2.85E+06 8.28E+05 9.13 OK. 201.50 OK.
Section 10 1130.973 14.400 300.000 74.223 1.84E+08 2.48E+06 4.85E+05 6.54 OK. 214.67 OK.
Section 11 1696.460 14.400 300.000 85.221 2.21E+08 2.60E+06 6.63E+05 6.07 OK. 129.65 OK.
Section 12 1130.973 14.400 300.000 64.773 1.09E+08 1.68E+06 3.76E+05 8.02 OK. 229.71 OK.
Section 13 1130.973 14.400 300.000 64.773 1.09E+08 1.68E+06 3.76E+05 7.58 OK. 217.05 OK.

16 Serviceability Limit State Check for Crack Width for Outer & Inner wall

Moment of
Moment fck fyk fctm fcm Cover Width, Depth, Ecm Es σtop = σbottom
Location d (mm) Inertia Remark
(kN-m) (MPa) (MPa) (MPa) (MPa) (mm) b (mm) D (mm) (MPa) (MPa) 4 (N/mm2)
(mm )
Section 9 87.9 30 500 2.501 40 75 1000 419 500 31186.6 200000 1.042E+10 2.110 Section is Uncracked
Section 10 68.2 30 500 2.501 40 40 1000 454 500 31186.6 200000 1.042E+10 1.637 Section is Uncracked
Section 11 40.4 30 500 2.501 40 75 1000 419 500 31186.6 200000 1.042E+10 0.970 Section is Uncracked
Section 12 26.5 30 500 2.501 40 40 1000 354 400 31186.6 200000 5.333E+09 0.994 Section is Uncracked
Section 13 19.2 30 500 2.501 40 40 1000 354 400 31186.6 200000 5.333E+09 0.720 Section is Uncracked

Total Ast Permissible Permissible Cracked

dc σconcrete σsteel
Location Provied Stress in Stress in Moment of Zc (mm3) Zs (mm3) Remark Remark
(mm) (N/mm2) (N/mm2)
(mm2/m) concrete Steel Inertia (mm4)
Section 9 2136.283 10.800 300.000 94.32 2.69E+08 2.85E+06 8.28E+05 4.81 OK. 106.17 OK.
Section 10 1130.973 10.800 300.000 74.223 1.84E+08 2.48E+06 4.85E+05 4.28 OK. 140.48 OK.
Section 11 1696.460 10.800 300.000 85.221 2.21E+08 2.60E+06 6.63E+05 2.43 OK. 60.97 OK.
Section 12 1130.973 10.800 300.000 64.773 1.09E+08 1.68E+06 3.76E+05 2.46 OK. 70.49 OK.
Section 13 1130.973 10.800 300.000 64.773 1.09E+08 1.68E+06 3.76E+05 1.78 OK. 51.07 OK.

Ac,eff Bar Crack Permissible

α= hc,eff Min Designed Sr,max
Location ρp,eff kt k1 k2 Єsm - Єcm Dia. Ф Width W k Crack Width Remark
Es/Ecm (mm) (mm )
2 (Єsm - Єcm) (Єsm - Єcm) (mm)
(mm) (mm) (mm)
Section 9 6.413 135.23 135227 0.0158 1.0 0.8 0.5 -3.41E-04 0.000319 3.19E-04 14.29 408.73 0.130 0.3 OK.
Section 10 6.413 115 115000 0.00983 1.0 0.8 0.5 -6.49E-04 0.000421 4.21E-04 12.00 343.43 0.145 0.3 OK.
Section 11 6.413 138.26 138260 0.01227 1.0 0.8 0.5 -7.94E-04 0.000183 1.83E-04 12.00 421.26 0.077 0.3 OK.
Section 12 6.413 111.74 111742 0.01012 1.0 0.8 0.5 -9.63E-04 0.000211 2.11E-04 12.00 337.56 0.071 0.3 OK.
Section 13 6.413 111.74 111742 0.01012 1.0 0.8 0.5 -1.06E-03 0.000153 1.53E-04 12.00 337.56 0.052 0.3 OK.

Walls Page 22
 17 ULS Shear Check for Top Slab

A. Elements Not requiring design shear reinforcement.

Cover = 40 mm
D = 500 mm
d = 500 - 40 - 12 /2 = 454.0 mm
bw = 1000 mm
fck = M 30 MPa
fyk = Fe 500 MPa
K = 1 + sqrt (200 / d )= 1.664 Eq. 10.2, Pg.88
Asl = Tensile reinforcement.
= 2136
ρl = Minimum of i.) Asl / (bw x d) = 0.0047
ii.) 0.02
= 0.0047
NEd = Axial force in the cross section from the loading or from prestressing
= 929720 N
Ac = bw x d = 454000 mm2
σcp = NEd / Ac < 0.2 x fcd fcd = 13.4 MPa
σcp = 2.04784
VEd = Design shear force at a cross section resulting from external loading and that
due to prestressing
= 187.795 kN

VRd.c = Maximum of

i.) [ 0.12 x K x (80 x ρl x fck)(1/3) + 0.15 x σcp] x bw x d Eq. 10.1, Pg.88

= 342813.657 N
= 342.81 kN

ii.) [0.031 x K(3/2) x fck(1/2) + 0.15 x σcp] x bw x d Eq. 10.3, Pg.88

= 304882.499 N
= 304.88 kN
VRd.c = 342.81 kN > VEd
Shear Reinforcement is not required.

Walls Page 23
 SUMMARY OF STEEL PROVIDED IN SLAB, RAFT AND WALLS

Description of steel provided in Slab

Depth = 450 Haunch 100 x 300
Sr. No. Description Dia spac Dia spac Steel Steel
Through out Extra Bar position

1 First support 12 200 + 12 200 1130 Top

2 First / Third span 12 100 + 0 100 1130 Bottom

3 Second Support 12 200 + 12 200 1130 Top

4 Second Span 12 100 + 0 100 1130 Bottom

5 Last Support 12 200 + 12 200 1130 Top

Description of Distribution Steel in Deck Slab

Top 8 T @200mm c/c
Bottom 8 T @200mm c/c

Description of steel provided in Raft

Depth = 350 Haunch 100 x 300
Sr. No. Description Dia spac Dia spac Steel Steel
Through out Extra Bar position

1 First support 12 200 + 16 200 1570 Bottom

First / Third
2 12 150 + 0 150 754 Top
span

3 Second Support 12 200 + 12 200 1130 Bottom

4 Second Span 12 150 + 0 150 754 Top

5 Last Support 12 200 + 16 200 754 Bottom

Description of Steel in Raft Slab

Top 8 T @150mm c/c
Bottom 8 T @150mm c/c

Page 24
Calculation of Main steel in wall designed as slab

Depth of End Wall = 500

Depth of Interior Wall = 400

Description of steel provided in Wall

Description Dia spac Dia spac Steel
End Wall Main Steel Extra L bar
On each face On Outer face
1 Top 12 100 + 12 200 1696
2 Middle 12 100 + 0 100 1130
3 Bottom 12 100 + 16 200 2135
Interior wall
4 Top 12 200 + 0 200 565
5 Bottom 12 200 + 0 200 565

Distribution steel
8 T @100mm c/c on each face of wall

Cut off wall be designed for differential earth pressure of 0.5 m Filling
0.5
Overall depth = 300 mm
Cover = 75 mm
Max dia = 8 mm
Effective depth = 300 - 75 - 8/2 = 221 mm

Max Pressure at base = 0.333 * 1.8 * 0.5 = 0.3 t/m2

Pressure Force = 0.5 * 0.2997 * 0.5 = 0.075 t/m
Max Moment = 0.075 * 0.5 / 3 = 0.013 t-m/m

Steel required = 0.0125x 1 e 7 /( 0.91 x 221x 200 )= 3.108 mm^2

Minimum steel 0.12% = 360 mm^2

Steel reqd on one face = 180 mm2

Steel provided 8 T 190 = 264.4 mm2 OK Vertical steel

Provide Tor 8 @ 190 C/C in Both Directions

Provide side face reinforcement of 8 tor @ 190 mm c/c on both face

Page 25
STAAD Input & OUTPUT

Page 26
STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 13-Apr-19
END JOB INFORMATION

UNIT METER MTON

JOINT COORDINATES
* Model for 3 Cell x 5m span x 4.825m Effective height
*RAFT COORDINATE
1 0 0 0;
R 1 0.25 0 0 ; R 1 0.5 0 0 ; R 6 0.59167 0 0 ; R 1 0.5 0 0 ; R 1 0.2 0 0
R 1 0.2 0 0 ; R 1 0.5 0 0 ; R 6 0.6 0 0 ; R 1 0.5 0 0 ; R 1 0.2 0 0
R 1 0.25 0 0 ; R 1 0.5 0 0 ; R 6 0.59167 0 0 ; R 1 0.5 0 0 ; R 1 0.2 0 0
*SLAB COORDINATE
1001 0 4.825 0
R 1 0.25 0 0 ; R 1 0.45 0 0 ; R 6 0.60833 0 0 ; R 1 0.45 0 0 ; R 1 0.2 0 0
R 1 0.2 0 0 ; R 1 0.45 0 0 ; R 6 0.61667 0 0 ; R 1 0.45 0 0 ; R 1 0.2 0 0
R 1 0.2 0 0 ; R 1 0.45 0 0 ; R 6 0.60833 0 0 ; R 1 0.45 0 0 ; R 1 0.25 0 0
*WALL COORDINATE
2001 0 0.25 0
R 1 0 0.5 0 ; R 6 0 0.558 0 ; R 1 0 0.5 0
2201 5 0.2 0
R 1 0 0.4 0 ; R 6 0 0.592 0 ; R 1 0 0.4 0
2401 10 0.2 0
R 1 0 0.4 0 ; R 6 0 0.592 0 ; R 1 0 0.4 0
2601 15 0.25 0
R 1 0 0.5 0 ; R 6 0 0.558 0 ; R 1 0 0.5 0

MEMBER INCIDENCES

1 1 2 30
101 1001 1002 130
1101 1 2001; 1102 2001 2002 1109; 1110 2009 1001
1201 11 2201; 1202 2201 2202 1209; 1210 2209 1011
1301 21 2401; 1302 2401 2402 1309; 1310 2409 1021
1401 31 2601; 1402 2601 2602 1409; 1410 2609 1031

START GROUP DEFINITION

MEMBER
_RAFT 1 TO 30
_SLAB 101 TO 130
_WALL1 1101 TO 1110
_WALL2 1201 TO 1210
_WALL3 1301 TO 1310
_WALL4 1401 TO 1410
_Secl 1 15 30 4 27 10 11 20 21 101 115 130 104 127 110 111 120 121
_Sec2 1101 1401 1105 1405 1110 1410 1201 1301 1210 1310

END GROUP DEFINITION

Page 27 DL_Staad
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 3.1623e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1.2e-005
DAMP 0.05
END DEFINE MATERIAL

CONSTANTS
MATERIAL CONCRETE ALL

MEMBER PROPERTY INDIAN

_RAFT PRIS YD 0.5 ZD 1.0
_WALL1 PRIS YD 0.5 ZD 1.0
_WALL2 PRIS YD 0.4 ZD 1.0
_WALL3 PRIS YD 0.4 ZD 1.0
_WALL4 PRIS YD 0.5 ZD 1.0
_SLAB PRIS YD 0.45 ZD 1.0

SUPPORTS
1 31 FIXED BUT MX MY MZ FZ KFY 375
2 30 FIXED BUT MX MY MZ FX FZ KFY 750
3 9 13 19 23 29 FIXED BUT MX MY MZ FX FZ KFY 818.7525
4 TO 8 14 to 18 24 TO 28 FIXED BUT MX MY MZ FX FZ KFY 887.505
10 12 20 22 FIXED BUT MX MY MZ FX FZ KFY 675
11 21 FIXED BUT MX MY MZ FX FZ KFY 600

LOAD 1 DEAD LOAD

*SELF WT OF MEMBERS
SELFWEIGHT Y -1
MEMBER LOAD
*CRASH BARRIER + SERVICE LOAD (0.1 )
101 TO 130 UNI GY -0.10

LOAD 2 WEARING COAT

MEMBER LOAD
* WEARING COAT
101 TO 130 UNI GY -0.1725

LOAD 3 EARTH PRESSURES AT REST

MEMBER LOAD
* EARTH PRESSURE ON FIRST WALL
1101 TRAP GX 5.050 4.800
1102 TRAP GX 4.800 4.300
1103 TRAP GX 4.300 3.742
1104 TRAP GX 3.742 3.184
1105 TRAP GX 3.184 2.626
1106 TRAP GX 2.626 2.068

Page 28 DL_Staad
1107 TRAP GX 2.068 1.510
1108 TRAP GX 1.510 0.952
1109 TRAP GX 0.952 0.452
1110 TRAP GX 0.452 0.227

* EARTH PRESSURE ON LAST WALL

1401 TRAP GX -5.050 -4.800
1402 TRAP GX -4.800 -4.300
1403 TRAP GX -4.300 -3.742
1404 TRAP GX -3.742 -3.184
1405 TRAP GX -3.184 -2.626
1406 TRAP GX -2.626 -2.068
1407 TRAP GX -2.068 -1.510
1408 TRAP GX -1.510 -0.952
1409 TRAP GX -0.952 -0.452
1410 TRAP GX -0.452 -0.227

* SKEW WATER CURRENT ON INTERMEDIATE WALL

1210 1310 TRAP GX 0.352 0.37
1209 1309 TRAP GX 0.315 0.352
1208 1308 TRAP GX 0.274 0.315
1207 1307 TRAP GX 0.233 0.274
1206 1306 TRAP GX 0.192 0.233
1205 1305 TRAP GX 0.152 0.192
1204 1304 TRAP GX 0.111 0.152
1203 1303 TRAP GX 0.07 0.111
1202 1302 TRAP GX 0.033 0.07
1201 1301 TRAP GX 0.017 0.033

LOAD 4 EARTH PRESSURES ACTIVE

MEMBER LOAD
* EARTH PRESSURE ON FIRST WALL
1101 TRAP GX 8.589 8.183
1102 TRAP GX 8.183 7.370
1103 TRAP GX 7.370 6.464
1104 TRAP GX 6.464 5.557
1105 TRAP GX 5.557 4.650
1106 TRAP GX 4.650 3.743
1107 TRAP GX 3.743 2.837
1108 TRAP GX 2.837 1.930
1109 TRAP GX 1.930 1.117
1110 TRAP GX 1.117 0.752

* EARTH PRESSURE ON LAST WALL

1401 TRAP GX -8.589 -8.183
1402 TRAP GX -8.183 -7.370
1403 TRAP GX -7.370 -6.464
1404 TRAP GX -6.464 -5.557
1405 TRAP GX -5.557 -4.650
1406 TRAP GX -4.650 -3.743

Page 29 DL_Staad
1407 TRAP GX -3.743 -2.837
1408 TRAP GX -2.837 -1.930
1409 TRAP GX -1.930 -1.117
1410 TRAP GX -1.117 -0.752

* SKEW WATER CURRENT ON INTERMEDIATE WALL

1210 1310 TRAP GX 0.352 0.37
1209 1309 TRAP GX 0.315 0.352
1208 1308 TRAP GX 0.274 0.315
1207 1307 TRAP GX 0.233 0.274
1206 1306 TRAP GX 0.192 0.233
1205 1305 TRAP GX 0.152 0.192
1204 1304 TRAP GX 0.111 0.152
1203 1303 TRAP GX 0.07 0.111
1202 1302 TRAP GX 0.033 0.07
1201 1301 TRAP GX 0.017 0.033

LOAD 5 SURCHARGE ONE SIDE

MEMBER LOAD
* EARTH PRESSURE ON FIRST WALL
1101 TO 1110 UNI GX 1.200

LOAD 6 SURCHARGE BOTH SIDES

MEMBER LOAD
* EARTH PRESSURE ON FIRST WALL
1101 TO 1110 UNI GX 1.200
1401 TO 1410 UNI GX -1.200

LOAD 7 BREAKING FORCE

JOINT LOAD
*BREAKING LOAD OF PER UNIT WIDTH
1001 FX 0.703125
1031 FX 0.703125

LOAD 8 TEMPERATURE LOADS(UNIFORM RISE)

TEMPERATURE LOAD
101 TO 130 TEMP 17.5

LOAD 9 TEMPERATURE LOADS(UNIFORM FALL)

TEMP LOAD
101 TO 130 TEMP -17.5
*SHRINKAGE
101 TO 130 TEMP -8.3335

LOAD 10 LOADTYPE None TITLE TEMPERATURE GRADIENT RISE

JOINT LOAD
1001 FX 35.028 MZ 4.452
1031 FX -35.028 MZ -4.452

LOAD 11 LOADTYPE None TITLE TEMPERATURE GRADIENT FALL

JOINT LOAD
1001 FX 17.221275 MZ 1.0205645625

Page 30 DL_Staad
1031 FX -17.221275 MZ -1.0205645625

*LOAD COMBINATIONS FOR VERIFICATION 0F STRUCTURAL STRENGTH

*STRUCTURAL STRENGTH *WITHOUT LIVE LOAD & TEMPERATURE
*COMB : 1.35DL+1.75WC+1.5EP AT REST
LOAD COMB 101 COMBINATION LOAD CASE 101
1 1.35 2 1.75 3 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE
LOAD COMB 102 COMBINATION LOAD CASE 102
1 1.35 2 1.75 3 1.5 5 1.2
*COMB :1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDES
LOAD COMB 103 COMBINATION LOAD CASE 103
1 1.35 2 1.75 3 1.5 6 1.2

*COMB : 1.35DL+1.7WC+1.5EP ACTIVE

LOAD COMB 104 COMBINATION LOAD CASE 104
1 1.35 2 1.75 4 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE
LOAD COMB 105 COMBINATION LOAD CASE 105
1 1.35 2 1.75 4 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDES
LOAD COMB 106 COMBINATION LOAD CASE 106
1 1.35 2 1.75 4 1.5

*STRUCTURAL STRENGTH WITH TEMPERATURE LEAD & LIVE LOAD ACCOMPANY

*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 107 COMBINATION LOAD CASE 107
1 1.35 2 1.75 3 1.5 5 1.2 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 108 COMBINATION LOAD CASE 108
1 1.35 2 1.75 3 1.5 6 1.2 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 109 COMBINATION LOAD CASE 109
1 1.35 2 1.75 4 1.5 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 110 COMBINATION LOAD CASE 110
1 1.35 2 1.75 4 1.5 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 111 COMBINATION LOAD CASE 111
1 1.35 2 1.75 3 1.0 5 1.2 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 112 COMBINATION LOAD CASE 112
1 1.35 2 1.75 3 1.0 6 1.2 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 113 COMBINATION LOAD CASE 113
1 1.35 2 1.75 4 1.5 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 114 COMBINATION LOAD CASE 114
1 1.35 2 1.75 4 1.5 8 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)

Page 31 DL_Staad
LOAD COMB 115 COMBINATION LOAD CASE 115
1 1.0 2 1.0 3 1.5 5 1.2 8 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 116 COMBINATION LOAD CASE 116
1 1.0 2 1.0 3 1.5 6 1.2 8 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 117 COMBINATION LOAD CASE 117
1 1.0 2 1.0 4 1.5 8 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP RISE(Lead)
LOAD COMB 118 COMBINATION LOAD CASE 118
1 1.0 2 1.0 4 1.5 8 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 119 COMBINATION LOAD CASE 119
1 1.35 2 1.75 3 1.5 5 1.2 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 120 COMBINATION LOAD CASE 120
1 1.35 2 1.75 3 1.5 6 1.2 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 121 COMBINATION LOAD CASE 121
1 1.35 2 1.75 4 1.5 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 122 COMBINATION LOAD CASE 122
1 1.35 2 1.75 4 1.5 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 123 COMBINATION LOAD CASE 123
1 1.35 2 1.75 3 1.0 5 1.2 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 124 COMBINATION LOAD CASE 124
1 1.35 2 1.75 3 1.0 6 1.2 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 125 COMBINATION LOAD CASE 125
1 1.35 2 1.75 4 1.5 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 126 COMBINATION LOAD CASE 126
1 1.35 2 1.75 4 1.5 9 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 127 COMBINATION LOAD CASE 127
1 1.0 2 1.0 3 1.5 5 1.2 9 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 128 COMBINATION LOAD CASE 128
1 1.0 2 1.0 3 1.5 6 1.2 9 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 129 COMBINATION LOAD CASE 129
1 1.0 2 1.0 4 1.5 9 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP FALL(Lead)
LOAD COMB 130 COMBINATION LOAD CASE 130
1 1.0 2 1.0 4 1.5 9 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 131 COMBINATION LOAD CASE 131
1 1.35 2 1.75 3 1.5 5 1.2 10 1.5 7 1.15

Page 32 DL_Staad
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 132 COMBINATION LOAD CASE 132
1 1.35 2 1.75 3 1.5 6 1.2 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 133 COMBINATION LOAD CASE 133
1 1.35 2 1.75 4 1.5 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 134 COMBINATION LOAD CASE 134
1 1.35 2 1.75 4 1.5 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 135 COMBINATION LOAD CASE 135
1 1.35 2 1.75 3 1.0 5 1.2 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 136 COMBINATION LOAD CASE 136
1 1.35 2 1.75 3 1.0 6 1.2 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 137 COMBINATION LOAD CASE 137
1 1.35 2 1.75 4 1.5 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 138 COMBINATION LOAD CASE 138
1 1.35 2 1.75 4 1.5 10 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 139 COMBINATION LOAD CASE 139
1 1.0 2 1.0 3 1.5 5 1.2 10 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 140 COMBINATION LOAD CASE 140
1 1.0 2 1.0 3 1.5 6 1.2 10 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 141 COMBINATION LOAD CASE 141
1 1.0 2 1.0 4 1.5 10 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT RISE (Lead)
LOAD COMB 142 COMBINATION LOAD CASE 142
1 1.0 2 1.0 4 1.5 10 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 143 COMBINATION LOAD CASE 143
1 1.35 2 1.75 3 1.5 5 1.2 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 144 COMBINATION LOAD CASE 144
1 1.35 2 1.75 3 1.5 6 1.2 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 145 COMBINATION LOAD CASE 145
1 1.35 2 1.75 4 1.5 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 146 COMBINATION LOAD CASE 146
1 1.35 2 1.75 4 1.5 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 147 COMBINATION LOAD CASE 147
1 1.35 2 1.75 3 1.0 5 1.2 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 148 COMBINATION LOAD CASE 148

Page 33 DL_Staad
1 1.35 2 1.75 3 1.0 6 1.2 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 149 COMBINATION LOAD CASE 149
1 1.35 2 1.75 4 1.5 11 1.5 7 1.15
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 150 COMBINATION LOAD CASE 150
1 1.35 2 1.75 4 1.5 11 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 151 COMBINATION LOAD CASE 151
1 1.0 2 1.0 3 1.5 5 1.2 11 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 152 COMBINATION LOAD CASE 152
1 1.0 2 1.0 3 1.5 5 1.2 11 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 153 COMBINATION LOAD CASE 153
1 1.0 2 1.0 4 1.5 11 1.5 7 1.15
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.15LL(Acc.)+1.15BRAKING(Acc.)+1.5TEMP GRADIENT FALL(Lead)
LOAD COMB 154 COMBINATION LOAD CASE 154
1 1.0 2 1.0 4 1.5 11 1.5 7 1.15

*STRUCTURAL STRENGTH *LIVE LOAD LEAD TEMPERATURE ACCOMPANY

*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 155 COMBINATION LOAD CASE 155
1 1.35 2 1.75 3 1.5 5 1.2 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 156 COMBINATION LOAD CASE 156
1 1.35 2 1.75 3 1.5 6 1.2 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 157 COMBINATION LOAD CASE 157
1 1.35 2 1.75 4 1.0 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 158 COMBINATION LOAD CASE 158
1 1.35 2 1.75 4 1.0 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 159 COMBINATION LOAD CASE 159
1 1.35 2 1.75 3 1.0 5 1.2 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 160 COMBINATION LOAD CASE 160
1 1.35 2 1.75 3 1.0 6 1.2 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 161 COMBINATION LOAD CASE 161
1 1.35 2 1.75 4 1.0 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 162 COMBINATION LOAD CASE 162
1 1.35 2 1.75 4 1.0 8 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 163 COMBINATION LOAD CASE 163
1 1.0 2 1.0 3 1.5 5 1.2 8 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 164 COMBINATION LOAD CASE 164

Page 34 DL_Staad
1 1.0 2 1.0 3 1.5 6 1.2 8 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 165 COMBINATION LOAD CASE 165
1 1.0 2 1.0 4 1.0 8 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP RISE(Acc.)
LOAD COMB 166 COMBINATION LOAD CASE 166
1 1.0 2 1.0 4 1.0 8 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 167 COMBINATION LOAD CASE 167
1 1.35 2 1.75 3 1.5 5 1.2 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 168 COMBINATION LOAD CASE 168
1 1.35 2 1.75 3 1.5 6 1.2 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 169 COMBINATION LOAD CASE 169
1 1.35 2 1.75 4 1.0 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 170 COMBINATION LOAD CASE 170
1 1.35 2 1.75 4 1.0 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 171 COMBINATION LOAD CASE 171
1 1.35 2 1.75 3 1.0 5 1.2 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 172 COMBINATION LOAD CASE 172
1 1.35 2 1.75 3 1.0 6 1.2 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 173 COMBINATION LOAD CASE 173
1 1.35 2 1.75 4 1.0 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 174 COMBINATION LOAD CASE 174
1 1.35 2 1.75 4 1.0 9 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 175 COMBINATION LOAD CASE 175
1 1.0 2 1.0 3 1.5 5 1.2 9 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 176 COMBINATION LOAD CASE 176
1 1.0 2 1.0 3 1.5 6 1.2 9 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 177 COMBINATION LOAD CASE 177
1 1.0 2 1.0 4 1.0 9 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP FALL(Acc.)
LOAD COMB 178 COMBINATION LOAD CASE 178
1 1.0 2 1.0 4 1.0 9 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 179 COMBINATION LOAD CASE 179
1 1.35 2 1.75 3 1.5 5 1.2 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 180 COMBINATION LOAD CASE 180
1 1.35 2 1.75 3 1.5 6 1.2 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)

Page 35 DL_Staad
LOAD COMB 181 COMBINATION LOAD CASE 181
1 1.35 2 1.75 4 1.0 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 182 COMBINATION LOAD CASE 182
1 1.35 2 1.75 4 1.0 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 183 COMBINATION LOAD CASE 183
1 1.35 2 1.75 3 1.0 5 1.2 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 184 COMBINATION LOAD CASE 184
1 1.35 2 1.75 3 1.0 6 1.2 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 185 COMBINATION LOAD CASE 185
1 1.35 2 1.75 4 1.0 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 186 COMBINATION LOAD CASE 186
1 1.35 2 1.75 4 1.0 10 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 187 COMBINATION LOAD CASE 187
1 1.0 2 1.0 3 1.5 5 1.2 10 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 188 COMBINATION LOAD CASE 188
1 1.0 2 1.0 3 1.5 6 1.2 10 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 189 COMBINATION LOAD CASE 189
1 1.0 2 1.0 4 1.0 10 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT RISE (Acc.)
LOAD COMB 190 COMBINATION LOAD CASE 190
1 1.0 2 1.0 4 1.0 10 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 191 COMBINATION LOAD CASE 191
1 1.35 2 1.75 3 1.5 5 1.2 11 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 192 COMBINATION LOAD CASE 192
1 1.35 2 1.75 3 1.5 6 1.2 11 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 193 COMBINATION LOAD CASE 193
1 1.35 2 1.75 4 1.0 11 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 194 COMBINATION LOAD CASE 194
1 1.35 2 1.75 4 1.0 11 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 195 COMBINATION LOAD CASE 195
1 1.35 2 1.75 3 1.0 5 1.2 11 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 196 COMBINATION LOAD CASE 196
1 1.35 2 1.75 3 1.0 6 1.2 11 0.9 7 1.5
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 197 COMBINATION LOAD CASE 197
1 1.35 2 1.75 4 1.0 11 0.9 7 1.5

Page 36 DL_Staad
*COMB : 1.35DL+1.75WC+1.0EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 198 COMBINATION LOAD CASE 198
1 1.35 2 1.75 4 1.0 11 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 199 COMBINATION LOAD CASE 199
1 1.0 2 1.0 3 1.5 5 1.2 11 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP AT REST+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 200 COMBINATION LOAD CASE 200
1 1.0 2 1.0 3 1.5 6 1.2 11 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE ONE SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 201 COMBINATION LOAD CASE 201
1 1.0 2 1.0 4 1.0 11 0.9 7 1.5
*COMB : 1.0DL+1.0WC+1.5EP ACTIVE+1.2SURCHARGE BOTH SIDE+1.5LL(Lead)+1.5BRAKING(Lead)+0.9TEMP GRADIENT FALL(Acc.)
LOAD COMB 202 COMBINATION LOAD CASE 202
1 1.0 2 1.0 4 1.0 11 0.9 7 1.5

*LOAD COMBINATIONS FOR VERIFICATION 0F SERVICEABILITY LIMIT STATE

*RARE COMBINATION
* SLS WITHOUT LIVE LOAD
*COMB : 1.0DL+1.2WC+1.0EP AT REST
LOAD COMB 301 COMBINATION LOAD CASE 301
1 1.0 2 1.2 3 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE
LOAD COMB 302 COMBINATION LOAD CASE 302
1 1.0 2 1.2 3 1.0 5 0.8
*COMB :1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDES
LOAD COMB 303 COMBINATION LOAD CASE 303
1 1.0 2 1.2 3 1.0 6 0.8
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE
LOAD COMB 304 COMBINATION LOAD CASE 304
1 1.0 2 1.2 4 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE
LOAD COMB 305 COMBINATION LOAD CASE 305
1 1.0 2 1.2 4 1.0
*COMB :1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDES
LOAD COMB 306 COMBINATION LOAD CASE 306
1 1.0 2 1.2 4 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST
LOAD COMB 307 COMBINATION LOAD CASE 307
1 1.0 2 1.0 3 1.0
*COMB : 1.0DL+1WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE
LOAD COMB 308 COMBINATION LOAD CASE 308
1 1.0 2 1.0 3 1.0 5 0.8
*COMB :1.0DL+1.WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDES
LOAD COMB 309 COMBINATION LOAD CASE 309
1 1.0 2 1.0 3 1.0 6 0.8
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE
LOAD COMB 310 COMBINATION LOAD CASE 310
1 1.0 2 1.0 4 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE

Page 37 DL_Staad
LOAD COMB 311 COMBINATION LOAD CASE 311
1 1.0 2 1.0 4 1.0
*COMB :1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDES
LOAD COMB 312 COMBINATION LOAD CASE 312
1 1.0 2 1.0 4 1.0

* SERVICEABILITY LIMIT STATE - TEMPERATURE LEAD LIVE LOADACCOMPANY

*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 313 COMBINATION LOAD CASE 313
1 1.0 2 1.2 3 1.0 5 0.8 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 314 COMBINATION LOAD CASE 314
1 1.0 2 1.2 3 1.0 6 0.8 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 315 COMBINATION LOAD CASE 315
1 1.0 2 1.2 4 1.0 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 316 COMBINATION LOAD CASE 316
1 1.0 2 1.2 4 1.0 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 317 COMBINATION LOAD CASE 317
1 1.0 2 1.2 3 1.0 5 0.8 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 318 COMBINATION LOAD CASE 318
1 1.0 2 1.2 3 1.0 6 0.8 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 319 COMBINATION LOAD CASE 319
1 1.0 2 1.2 4 1.0 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 320 COMBINATION LOAD CASE 320
1 1.0 2 1.2 4 1.0 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 321 COMBINATION LOAD CASE 321
1 1.0 2 1.2 3 1.0 5 0.8 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 322 COMBINATION LOAD CASE 322
1 1.0 2 1.2 3 1.0 6 0.8 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 323 COMBINATION LOAD CASE 323
1 1.0 2 1.2 4 1.0 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 324 COMBINATION LOAD CASE 324
1 1.0 2 1.2 4 1.0 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 325 COMBINATION LOAD CASE 325
1 1.0 2 1.2 3 1.0 5 0.8 11 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 326 COMBINATION LOAD CASE 326
1 1.0 2 1.2 3 1.0 6 0.8 11 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)

Page 38 DL_Staad
LOAD COMB 327 COMBINATION LOAD CASE 327
1 1.0 2 1.2 4 1.0 11 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 328 COMBINATION LOAD CASE 328
1 1.0 2 1.2 4 1.0 11 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 329 COMBINATION LOAD CASE 329
1 1.0 2 1.0 3 1.0 5 0.8 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 330 COMBINATION LOAD CASE 330
1 1.0 2 1.0 3 1.0 6 0.8 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 331 COMBINATION LOAD CASE 331
1 1.0 2 1.0 4 1.0 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP RISE(Lead)
LOAD COMB 332 COMBINATION LOAD CASE 332
1 1.0 2 1.0 4 1.0 8 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 333 COMBINATION LOAD CASE 333
1 1.0 2 1.0 3 1.0 5 0.8 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 334 COMBINATION LOAD CASE 334
1 1.0 2 1.0 3 1.0 6 0.8 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 335 COMBINATION LOAD CASE 335
1 1.0 2 1.0 4 1.0 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP FALL(Lead)
LOAD COMB 336 COMBINATION LOAD CASE 336
1 1.0 2 1.0 4 1.0 9 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 337 COMBINATION LOAD CASE 337
1 1.0 2 1.0 3 1.0 5 0.8 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 338 COMBINATION LOAD CASE 338
1 1.0 2 1.0 3 1.0 6 0.8 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 339 COMBINATION LOAD CASE 339
1 1.0 2 1.0 4 1.0 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT RISE(Lead)
LOAD COMB 340 COMBINATION LOAD CASE 340
1 1.0 2 1.0 4 1.0 10 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 341 COMBINATION LOAD CASE 341
1 1.0 2 1.0 3 1.0 5 0.8 11 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 342 COMBINATION LOAD CASE 342
1 1.0 2 1.0 3 1.0 6 0.8 11 1.0 7 0.75
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 343 COMBINATION LOAD CASE 343
1 1.0 2 1.0 4 1.0 11 1.0 7 0.75

Page 39 DL_Staad
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+0.75LL(Acc.)+0.75BRAKING(Acc.)+1.0TEMP GRADIENT FALL(Lead)
LOAD COMB 344 COMBINATION LOAD CASE 344
1 1.0 2 1.0 4 1.0 11 1.0 7 0.75

* SERVICEABILITY LIMIT STATE - LIVE LOAD LEAD TEMPERATURE ACCOMPANY

*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 345 COMBINATION LOAD CASE 345
1 1.0 2 1.2 3 1.0 5 0.8 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 346 COMBINATION LOAD CASE 346
1 1.0 2 1.2 3 1.0 6 0.8 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 347 COMBINATION LOAD CASE 347
1 1.0 2 1.2 4 1.0 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 348 COMBINATION LOAD CASE 348
1 1.0 2 1.2 4 1.0 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 349 COMBINATION LOAD CASE 349
1 1.0 2 1.2 3 1.0 5 0.8 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 350 COMBINATION LOAD CASE 350
1 1.0 2 1.2 3 1.0 6 0.8 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 351 COMBINATION LOAD CASE 351
1 1.0 2 1.2 4 1.0 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 352 COMBINATION LOAD CASE 352
1 1.0 2 1.2 4 1.0 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 353 COMBINATION LOAD CASE 353
1 1.0 2 1.2 3 1.0 5 0.8 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 354 COMBINATION LOAD CASE 354
1 1.0 2 1.2 3 1.0 6 0.8 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 355 COMBINATION LOAD CASE 355
1 1.0 2 1.2 4 1.0 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 356 COMBINATION LOAD CASE 356
1 1.0 2 1.2 4 1.0 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 357 COMBINATION LOAD CASE 357
1 1.0 2 1.2 3 1.0 5 0.8 11 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 358 COMBINATION LOAD CASE 358
1 1.0 2 1.2 3 1.0 6 0.8 11 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 359 COMBINATION LOAD CASE 359
1 1.0 2 1.2 4 1.0 11 0.6 7 1.0

Page 40 DL_Staad
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 360 COMBINATION LOAD CASE 360
1 1.0 2 1.2 4 1.0 11 0.6 7 1.0
*COMB : 1.0DL+1.2WC
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 361 COMBINATION LOAD CASE 361
1 1.0 2 1.0 3 1.0 5 0.8 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 362 COMBINATION LOAD CASE 362
1 1.0 2 1.0 3 1.0 6 0.8 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 363 COMBINATION LOAD CASE 363
1 1.0 2 1.0 4 1.0 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP RISE(Acc.)
LOAD COMB 364 COMBINATION LOAD CASE 364
1 1.0 2 1.0 4 1.0 8 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 365 COMBINATION LOAD CASE 365
1 1.0 2 1.0 3 1.0 5 0.8 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 366 COMBINATION LOAD CASE 366
1 1.0 2 1.0 3 1.0 6 0.8 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 367 COMBINATION LOAD CASE 367
1 1.0 2 1.0 4 1.0 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP FALL(Acc.)
LOAD COMB 368 COMBINATION LOAD CASE 368
1 1.0 2 1.0 4 1.0 9 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 369 COMBINATION LOAD CASE 369
1 1.0 2 1.0 3 1.0 5 0.8 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 370 COMBINATION LOAD CASE 370
1 1.0 2 1.0 3 1.0 6 0.8 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 371 COMBINATION LOAD CASE 371
1 1.0 2 1.0 4 1.0 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT RISE(Acc.)
LOAD COMB 372 COMBINATION LOAD CASE 372
1 1.0 2 1.0 4 1.0 10 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 373 COMBINATION LOAD CASE 373
1 1.0 2 1.0 3 1.0 5 0.8 11 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 374 COMBINATION LOAD CASE 374
1 1.0 2 1.0 3 1.0 6 0.8 11 0.6 7 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.8SURCHARGE ONE SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)
LOAD COMB 375 COMBINATION LOAD CASE 375
1 1.0 2 1.0 4 1.0 11 0.6 7 1.0
*COMB : 1.0DL+1WC+1.0EP ACTIVE+0.8SURCHARGE BOTH SIDE+1.0LL(Lead)+1.0BRAKING(Lead)+0.6TEMP GRADIENT FALL(Acc.)

Page 41 DL_Staad
LOAD COMB 376 COMBINATION LOAD CASE 376
1 1.0 2 1.0 4 1.0 11 0.6 7 1.0

*QUASI-PERMANENT COMBINATION
*COMB : 1.0DL+1.2WC+ 1.0 EP
LOAD COMB 401 COMBINATION LOAD CASE 401
1 1.0 2 1.2 3 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST
LOAD COMB 402 COMBINATION LOAD CASE 402
1 1.0 2 1.2 3 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE
LOAD COMB 403 COMBINATION LOAD CASE 403
1 1.0 2 1.2 4 1.0

*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP RISE(Acc.)

LOAD COMB 404 COMBINATION LOAD CASE 404
1 1.0 2 1.2 3 1.0 8 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP RISE(Acc.)
LOAD COMB 405 COMBINATION LOAD CASE 405
1 1.0 2 1.2 4 1.0 8 0.5
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP FALL(Acc.)
LOAD COMB 406 COMBINATION LOAD CASE 406
1 1.0 2 1.2 3 1.0 9 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP FALL(Acc.)
LOAD COMB 407 COMBINATION LOAD CASE 407
1 1.0 2 1.2 4 1.0 9 0.5
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP GRADIENT RISE(Acc.)
LOAD COMB 408 COMBINATION LOAD CASE 408
1 1.0 2 1.2 3 1.0 10 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP GRADIENT RISE(Acc.)
LOAD COMB 409 COMBINATION LOAD CASE 409
1 1.0 2 1.2 4 1.0 10 0.5
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP GRADIENT FALL(Acc.)
LOAD COMB 410 COMBINATION LOAD CASE 410
1 1.0 2 1.2 3 1.0 11 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP GRADIENT FALL(Acc.)
LOAD COMB 411 COMBINATION LOAD CASE 411
1 1.0 2 1.2 4 1.0 11 0.5
*COMB : 1.0DL+1.0WC+1.0 EP
LOAD COMB 412 COMBINATION LOAD CASE 412
1 1.0 2 1.0 3 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST
LOAD COMB 413 COMBINATION LOAD CASE 413
1 1.0 2 1.0 3 1.0
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE
LOAD COMB 414 COMBINATION LOAD CASE 414
1 1.0 2 1.0 4 1.0
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP RISE(Acc.)
LOAD COMB 415 COMBINATION LOAD CASE 415

Page 42 DL_Staad
1 1.0 2 1.0 3 1.0 8 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP RISE(Acc.)
LOAD COMB 416 COMBINATION LOAD CASE 416
1 1.0 2 1.0 4 1.0 8 0.5
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP FALL(Acc.)
LOAD COMB 417 COMBINATION LOAD CASE 417
1 1.0 2 1.0 3 1.0 9 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP FALL(Acc.)
LOAD COMB 418 COMBINATION LOAD CASE 418
1 1.0 2 1.0 4 1.0 9 0.5
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP GRADIENT RISE(Acc.)
LOAD COMB 419 COMBINATION LOAD CASE 419
1 1.0 2 1.0 3 1.0 10 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP GRADIENT RISE(Acc.)
LOAD COMB 420 COMBINATION LOAD CASE 420
1 1.0 2 1.0 4 1.0 10 0.5
*COMB : 1.0DL+1.2WC+1.0EP AT REST+0.5TEMP GRADIENT FALL(Acc.)
LOAD COMB 421 COMBINATION LOAD CASE 421
1 1.0 2 1.0 3 1.0 11 0.5
*COMB : 1.0DL+1.2WC+1.0EP ACTIVE+0.5TEMP GRADIENT FALL(Acc.)
LOAD COMB 422 COMBINATION LOAD CASE 422
1 1.0 2 1.0 4 1.0 11 0.5

PERFORM ANALYSIS

DEFINE ENVELOPE
101 TO 106 ENVELOPE 1 TYPE STRENGTH
107 TO 154 ENVELOPE 2 TYPE STRENGTH
155 TO 202 ENVELOPE 3 TYPE STRENGTH

301 TO 312 ENVELOPE 4 TYPE SERVICEABILITY

313 TO 344 ENVELOPE 5 TYPE SERVICEABILITY
345 TO 376 ENVELOPE 6 TYPE SERVICEABILITY

401 TO 410 ENVELOPE 7 TYPE STRESS

END DEFINE ENVELOPE

LOAD LIST 101 TO 106

PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309
PRINT MAXFORCE ENVOLUPE LIST 3 28 103 128 1103 1403
LOAD LIST 107 TO 154
PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309
PRINT MAXFORCE ENVOLUPE LIST 3 28 103 128 1103 1403
LOAD LIST 155 TO 202
PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115

Page 43 DL_Staad
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309
PRINT MAXFORCE ENVOLUPE LIST 3 28 103 128 1103 1403
LOAD LIST 301 TO 312
PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309

LOAD LIST 313 TO 344

PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309

LOAD LIST 345 TO 307

PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309

LOAD LIST 401 TO 410

PRINT MAXFORCE ENVOLUPE LIST 2 29 5 26 9 11 19 22 15 -
102 129 105 125 109 111 119 122 115
PRINT MAXFORCE ENVOLUPE LIST 1102 1402 1105 1405 1109 1409 1202 1302 1209 1309

FINISH

23.711 22.198 22.198 23.711

13.866 13.866

17.718 11.715 14.524 17.718

9.85 9.85

12.755 12.384 7.208 12.755

22.825 22.825

25.213 19.763 19.763 25.213

Load 0 : Bending Z

Factorised BMD Envolope for ULS (KN-m) (DL + LL)

Page 44 DL_Staad
STAAD OUTPUT FOR ULS DEAD LOAD + NO LIVE LOAD
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -8.47 0 101 -4.86 0.5 101

0 0 101 0 0 101 1.17 T 0 104
MIN -10.29 0.5 106 -12.88 0 106
0 0.5 106 0 0.5 106 2.29 T 0.5 102

29 MAX 10.3 0 104 -1.96 0 102

0 0 101 0 0 101 1.99 C 0 102
MIN 8.48 0.5 101 -11.62 0.5 106
0 0.5 106 0 0.5 106 0.9 C 0.5 101

5 MAX -1.94 0 101 3.27 0.59 101

0 0 101 0 0 101 1.17 T 0 104
MIN -3.91 0.59 102 -0.24 0 102
0 0.59 106 0 0.59 106 2.29 T 0.59 102

26 MAX 3.34 0 104 4.86 0 102

0 0 101 0 0 101 1.99 C 0 102
MIN 0.88 0.59 102 0.84 0.59 106
0 0.59 106 0 0.59 106 0.9 C 0.59 101

9 MAX 5.7 0 101 1.06 0 102

0 0 101 0 0 101 1.17 T 0 104
MIN 3.61 0.5 102 -2.1 0.5 101
0 0.5 106 0 0.5 106 2.29 T 0.5 102

11 MAX -7.97 0 104 -4.39 0.2 104

0 0 101 0 0 101 0.31 C 0 101
MIN -8.95 0.2 102 -7.87 0 102
0 0.2 106 0 0.2 106 0.24 C 0.2 106

19 MAX 6.15 0 101 1.16 0 102

0 0 101 0 0 101 0.31 C 0 101
MIN 4.68 0.5 102 -2.88 0.5 101
0 0.5 106 0 0.5 106 0.24 C 0.5 106

22 MAX -4.96 0 104 -0.02 0.5 103

0 0 101 0 0 101 1.99 C 0 102
MIN -7.45 0.5 102 -4.01 0 102
0 0.5 106 0 0.5 106 0.9 C 0.5 101

15 MAX -0.77 0 104 4.3 0.6 104

0 0 101 0 0 101 0.31 C 0 101
MIN -2.39 0.6 102 2.91 0 102
0 0.6 106 0 0.6 106 0.24 C 0.6 106

102 MAX 4.52 0 104 4.23 0 104

0 0 101 0 0 101 10 C 0 104
MIN 2.75 0.45 102 -0.18 0.45 101
0 0.45 106 0 0.45 106 4.6 C 0.45 101

129 MAX -3.25 0 101 5.78 0.45 104

0 0 101 0 0 101 10.72 C 0 104
MIN -4.98 0.45 106 1.17 0 101
0 0.45 106 0 0.45 106 5.32 C 0.45 101

ULS_ENV 45
 105 MAX 1.27 0 104 -0.6 0 104
0 0 101 0 0 101 10 C 0 104
MIN -0.82 0.61 102 -2.17 0.2 101
0 0.61 106 0 0.61 106 4.6 C 0.61 101

125 MAX 1.51 0 101 -0.44 0 104

0 0 101 0 0 101 10.72 C 0 104
MIN -0.53 0.61 106 -1.5 0.61 101
0 0.61 106 0 0.61 106 5.32 C 0.61 101

109 MAX -3.49 0 104 5.04 0.45 102

0 0 101 0 0 101 10 C 0 104
MIN -5.27 0.45 102 2.11 0 106
0 0.45 106 0 0.45 106 4.6 C 0.45 101

111 MAX 4.69 0 101 4.02 0 101

0 0 101 0 0 101 10 C 0 104
MIN 3.49 0.2 102 1.14 0.2 102
0 0.2 106 0 0.2 106 4.5 C 0.2 101

119 MAX -3.82 0 101 5.76 0.45 102

0 0 101 0 0 101 10 C 0 104
MIN -5.5 0.45 102 1.58 0 106
0 0.45 106 0 0.45 106 4.5 C 0.45 101

122 MAX 4.77 0 101 4.3 0 101

0 0 101 0 0 101 10.72 C 0 104
MIN 3.04 0.45 106 1.81 0.45 106
0 0.45 106 0 0.45 106 5.32 C 0.45 101

115 MAX 1.01 0 101 -1.34 0 101

0 0 101 0 0 101 10 C 0 104
MIN -1.01 0.62 102 -2.15 0.51 106
0 0.62 106 0 0.62 106 4.5 C 0.62 101

1102 MAX 20.65 0 104 10.91 0 102

0 0 101 0 0 101 12.73 C 0 104
MIN 9.23 0.5 101 1.49 0.5 106
0 0.5 106 0 0.5 106 10.99 C 0.5 102

1402 MAX -7.88 0.5 102 -0.23 0.5 104

0 0 101 0 0 101 13.19 C 0 104
MIN -19.93 0 106 -8.71 0 106
0 0.5 106 0 0.5 106 11.49 C 0.5 101

1105 MAX 4.42 0 102 -3.4 0 101

0 0 101 0 0 101 10.01 C 0 104
MIN -0.28 0.56 106 -9.73 0.51 106
0 0.56 106 0 0.56 106 8.17 C 0.56 102

1405 MAX 1 0.56 104 9.85 0.42 104

0 0 101 0 0 101 10.46 C 0 104
MIN -3.28 0 106 3.86 0 101
0 0.56 106 0 0.56 106 8.67 C 0.56 101

1109 MAX -3.96 0 101 3.18 0.5 104

0 0 101 0 0 101 6.24 C 0 104
MIN -9.68 0.5 106 -2.55 0 102
0 0.5 106 0 0.5 106 4.5 C 0.5 102

ULS_ENV 46
 1409 MAX 10.4 0.5 104 0.32 0 103
0 0 101 0 0 101 6.69 C 0 104
MIN 4.68 0 101 -4.69 0.5 106
0 0.5 106 0 0.5 106 5C 0.5 101

1202 MAX 2.57 0 102 5.27 0 102

0 0 101 0 0 101 16.55 C 0 101
MIN 1.38 0.4 106 2.12 0.4 101
0 0.4 106 0 0.4 106 15.16 C 0.4 106

1302 MAX 1.69 0 102 3.1 0 102

0 0 101 0 0 101 16.84 C 0 102
MIN 0.55 0.4 101 0.24 0.4 106
0 0.4 106 0 0.4 106 15.11 C 0.4 106

1209 MAX 1.52 0 102 -1.21 0 104

0 0 101 0 0 101 11.22 C 0 101
MIN 0.15 0.4 106 -3.91 0.4 102
0 0.4 106 0 0.4 106 9.82 C 0.4 106

1309 MAX 0.64 0 102 0.07 0.4 101

0 0 101 0 0 101 11.5 C 0 102
MIN -0.67 0.4 101 -2.27 0.4 102
0 0.4 106 0 0.4 106 9.77 C 0.4 106

3 MAX -6.26 0 101 -0.86 0.59 101

0 0 101 0 0 101 1.17 T 0 104
MIN -8.25 0.59 106 -7.95 0 106
0 0.59 106 0 0.59 106 2.29 T 0.59 102

28 MAX 8.07 0 104 1.81 0 102

0 0 101 0 0 101 1.99 C 0 102
MIN 5.87 0.59 102 -6.68 0.59 106
0 0.59 106 0 0.59 106 0.9 C 0.59 101

103 MAX 3.64 0 104 2.39 0 104

0 0 101 0 0 101 10 C 0 104
MIN 1.56 0.61 102 -1.52 0.61 101
0 0.61 106 0 0.61 106 4.6 C 0.61 101

128 MAX -2.06 0 101 3.74 0.61 104

0 0 101 0 0 101 10.72 C 0 104
MIN -4.1 0.61 106 -0.44 0 101
0 0.61 106 0 0.61 106 5.32 C 0.61 101

1103 MAX 14.82 0 104 3.75 0 102

0 0 101 0 0 101 11.89 C 0 104
MIN 5.87 0.56 101 -5.13 0.56 106
0 0.56 106 0 0.56 106 10.05 C 0.56 102

1403 MAX -4.51 0.56 102 5.99 0.56 104

0 0 101 0 0 101 12.34 C 0 104
MIN -14.1 0 106 -1.97 0 101
0 0.56 106 0 0.56 106 10.55 C 0.56 101

ULS_ENV 47
STAAD OUTPUT FOR ULS DEAD LOAD + LIVE LOAD (ACC)
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -6.87 0 115 -1.94 0.5 112

0 0 107 0 0 107 1.16 T 0 112
MIN -10.8 0.5 138 -18.68 0 126
0 0.5 154 0 0.5 154 3.1 T 0.5 119

29 MAX 10.87 0 133 3.28 0 111

0 0 107 0 0 107 2.77 C 0 115
MIN 6.56 0.5 115 -15.98 0.5 126
0 0.5 154 0 0.5 154 0.76 C 0.5 124

5 MAX -1.25 0 112 5.22 0.59 112

0 0 107 0 0 107 1.16 T 0 112
MIN -5.41 0.59 119 -6.22 0 127
0 0.59 154 0 0.59 154 3.1 T 0.59 119

26 MAX 4.34 0 121 8.03 0.59 111

0 0 107 0 0 107 2.77 C 0 115
MIN -0.51 0.59 111 -3.94 0.59 130
0 0.59 154 0 0.59 154 0.76 C 0.59 124

9 MAX 6.06 0 112 2.01 0 107

0 0 107 0 0 107 1.16 T 0 112
MIN 0.54 0.5 127 -2.53 0.5 124
0 0.5 154 0 0.5 154 3.1 T 0.5 119

11 MAX -5.12 0 117 -2.2 0.2 117

0 0 107 0 0 107 0.91 C 0 123
MIN -10.8 0.2 119 -11.49 0 119
0 0.2 154 0 0.2 154 0.26 T 0.2 118

19 MAX 7.27 0 124 3.4 0 115

0 0 107 0 0 107 0.91 C 0 123
MIN 1.86 0.5 115 -5 0.5 124
0 0.5 154 0 0.5 154 0.26 T 0.5 118

22 MAX -2.77 0 129 0.71 0.5 112

0 0 107 0 0 107 2.77 C 0 115
MIN -8.62 0.5 111 -5.1 0 119
0 0.5 154 0 0.5 154 0.76 C 0.5 124

15 MAX -0.8 0 112 4.85 0.6 109

0 0 107 0 0 107 0.91 C 0 123
MIN -2.9 0.6 119 0.97 0 127
0 0.6 154 0 0.6 154 0.26 T 0.6 118

102 MAX 5.02 0 109 7.05 0 117

0 0 107 0 0 107 62.12 C 0 141
MIN 0.91 0.45 127 -5.63 0.45 123
0 0.45 154 0 0.45 154 3.88 C 0.45 123

129 MAX -2.24 0 128 9.94 0.45 117

0 0 107 0 0 107 61.8 C 0 141
MIN -5.91 0.45 114 -2.38 0 123
0 0.45 154 0 0.45 154 1.16 C 0.45 123

ULS_ENV 48
 105 MAX 1.87 0 117 2 0 117
0 0 107 0 0 107 62.12 C 0 141
MIN -2.39 0.61 123 -5.62 0 123
0 0.61 154 0 0.61 154 3.88 C 0.61 123

125 MAX 2.37 0 124 1.99 0.61 117

0 0 107 0 0 107 61.8 C 0 141
MIN -1.9 0.61 118 -3.58 0.61 123
0 0.61 154 0 0.61 154 1.16 C 0.61 123

109 MAX -1.53 0 117 5.97 0.45 123

0 0 107 0 0 107 62.12 C 0 141
MIN -6.84 0.45 123 1.25 0 130
0 0.45 154 0 0.45 154 3.88 C 0.45 123

111 MAX 4.44 0 112 4.4 0 112

0 0 107 0 0 107 61.71 C 0 141
MIN 1.85 0.2 127 -2.39 0.2 127
0 0.2 154 0 0.2 154 1.15 C 0.2 123

119 MAX -3.13 0 116 7.59 0.45 111

0 0 107 0 0 107 61.71 C 0 141
MIN -5.85 0.45 119 0.04 0 130
0 0.45 154 0 0.45 154 1.15 C 0.45 123

122 MAX 5.63 0 124 4.29 0 124

0 0 107 0 0 107 61.8 C 0 141
MIN 0.65 0.45 118 0.52 0.45 130
0 0.45 154 0 0.45 154 1.16 C 0.45 123

115 MAX 0.76 0 112 -0.43 0.62 115

0 0 107 0 0 107 61.71 C 0 141
MIN -1.36 0.62 127 -3.72 0.36 126
0 0.62 154 0 0.62 154 1.15 C 0.62 123

1102 MAX 22.95 0 121 15.94 0 119

0 0 107 0 0 107 13.23 C 0 109
MIN 8.02 0.5 112 -1.73 0.5 118
0 0.5 154 0 0.5 154 6.98 C 0.5 127

1402 MAX -3.87 0.5 111 3.91 0.5 117

0 0 107 0 0 107 14.12 C 0 109
MIN -21.65 0 126 -12.54 0 126
0 0.5 154 0 0.5 154 8.32 C 0.5 128

1105 MAX 6.72 0 119 -1.81 0 123

0 0 107 0 0 107 10.5 C 0 109
MIN -1.74 0.56 118 -11.88 0.56 142
0 0.56 154 0 0.56 154 4.89 C 0.56 127

1405 MAX 3.03 0.56 117 11.89 0.51 141

0 0 107 0 0 107 11.4 C 0 109
MIN -5 0 126 0.72 0 123
0 0.56 154 0 0.56 154 6.22 C 0.56 128

1109 MAX -1.6 0 123 5.58 0.5 117

0 0 107 0 0 107 6.73 C 0 109
MIN -11.14 0.5 118 -6.76 0 139
0 0.5 154 0 0.5 154 2.17 C 0.5 127

ULS_ENV 49
 1409 MAX 12.44 0.5 117 3.51 0 140
0 0 107 0 0 107 7.63 C 0 109
MIN 1.54 0 123 -8.39 0.5 118
0 0.5 154 0 0.5 154 3.51 C 0.5 128

1202 MAX 3.98 0 119 8.56 0 119

0 0 107 0 0 107 17.45 C 0 124
MIN 1.04 0.4 112 1.47 0.4 112
0 0.4 154 0 0.4 154 9.61 C 0.4 118

1302 MAX 2.97 0 115 5.95 0 115

0 0 107 0 0 107 18.37 C 0 123
MIN -0.16 0.4 124 -0.93 0 124
0 0.4 154 0 0.4 154 9.82 C 0.4 118

1209 MAX 2.96 0 123 -0.76 0 117

0 0 107 0 0 107 12.11 C 0 124
MIN -0.09 0.4 118 -6.74 0.4 119
0 0.4 154 0 0.4 154 5.66 C 0.4 118

1309 MAX 1.91 0 115 1.04 0.4 124

0 0 107 0 0 107 13.03 C 0 123
MIN -1 0.4 120 -4.96 0.4 115
0 0.4 154 0 0.4 154 5.87 C 0.4 118

3 MAX -5.07 0 116 1.84 0.59 112

0 0 107 0 0 107 1.16 T 0 112
MIN -8.99 0.59 126 -13.76 0 130
0 0.59 154 0 0.59 154 3.1 T 0.59 119

28 MAX 8.62 0 121 6.52 0 111

0 0 107 0 0 107 2.77 C 0 115
MIN 4.03 0.59 115 -10.99 0.59 126
0 0.59 154 0 0.59 154 0.76 C 0.59 124

103 MAX 4.14 0 109 5.31 0 117

0 0 107 0 0 107 62.12 C 0 141
MIN -0.01 0.61 123 -5.99 0.61 123
0 0.61 154 0 0.61 154 3.88 C 0.61 123

128 MAX -1.2 0 124 7.8 0.61 117

0 0 107 0 0 107 61.8 C 0 141
MIN -5.03 0.61 114 -3.5 0 123
0 0.61 154 0 0.61 154 1.16 C 0.61 123

1103 MAX 17.12 0 121 8.26 0 123

0 0 107 0 0 107 12.38 C 0 109
MIN 4.97 0.56 112 -7.53 0.56 118
0 0.56 154 0 0.56 154 6.28 C 0.56 127

1403 MAX -1.62 0.56 111 8.99 0.56 117

0 0 107 0 0 107 13.28 C 0 109
MIN -15.82 0 126 -5.46 0 124
0 0.56 154 0 0.56 154 7.62 C 0.56 128

ULS_ENV 50
STAAD OUTPUT FOR ULS DEAD LOAD + LIVE LOAD (LEAD)
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -6.69 0 165 -3.53 0.5 160

0 0 155 0 0 155 1.34 T 0 165
MIN -10.06 0.5 180 -16.47 0 167
0 0.5 202 0 0.5 202 3.14 T 0.5 167

29 MAX 10.14 0 180 2.14 0 159

0 0 155 0 0 155 2.84 C 0 163
MIN 6.59 0.5 163 -11.75 0.5 168
0 0.5 202 0 0.5 202 1.03 C 0.5 172

5 MAX -1.67 0 160 4.2 0.59 160

0 0 155 0 0 155 1.34 T 0 165
MIN -4.99 0.59 167 -4.78 0 175
0 0.59 202 0 0.59 202 3.14 T 0.59 167

26 MAX 3.27 0 168 7.26 0 159

0 0 155 0 0 155 2.84 C 0 163
MIN -0.24 0.59 159 -1.05 0.59 176
0 0.59 202 0 0.59 202 1.03 C 0.59 172

9 MAX 5.69 0 160 1.76 0 155

0 0 155 0 0 155 1.34 T 0 165
MIN 0.78 0.5 175 -2.15 0.5 172
0 0.5 202 0 0.5 202 3.14 T 0.5 167

11 MAX -5.55 0 165 -3.09 0.2 165

0 0 155 0 0 155 0.68 C 0 171
MIN -10.28 0.2 167 -10.6 0 167
0 0.2 202 0 0.2 202 0.06 T 0.2 164

19 MAX 6.65 0 172 3.07 0 163

0 0 155 0 0 155 0.68 C 0 171
MIN 2.11 0.5 163 -3.77 0.5 172
0 0.5 202 0 0.5 202 0.06 T 0.5 164

22 MAX -3.65 0 176 0.34 0.5 160

0 0 155 0 0 155 2.84 C 0 163
MIN -8.5 0.5 159 -4.93 0 167
0 0.5 202 0 0.5 202 1.03 C 0.5 172

15 MAX -0.85 0 165 4.45 0.6 156

0 0 155 0 0 155 0.68 C 0 171
MIN -2.92 0.6 167 1.28 0 175
0 0.6 202 0 0.6 202 0.06 T 0.6 164

102 MAX 4.23 0 156 4.13 0 164

0 0 155 0 0 155 39.83 C 0 188
MIN 1.26 0.45 175 -4.19 0.45 171
0 0.45 202 0 0.45 202 4.84 C 0.45 171

129 MAX -2.45 0 177 7.42 0.45 164

0 0 155 0 0 155 39.19 C 0 188
MIN -5.31 0.45 155 -0.59 0 171
0 0.45 202 0 0.45 202 1.81 C 0.45 171

ULS_ENV 51
 105 MAX 1.08 0 164 0.39 0 164
0 0 155 0 0 155 39.83 C 0 188
MIN -2.04 0.61 171 -4.61 0 171
0 0.61 202 0 0.61 202 4.84 C 0.61 171

125 MAX 1.88 0 172 0.97 0.61 164

0 0 155 0 0 155 39.19 C 0 188
MIN -1.3 0.61 163 -2.68 0.61 171
0 0.61 202 0 0.61 202 1.81 C 0.61 171

109 MAX -2.32 0 164 5.96 0.45 171

0 0 155 0 0 155 39.83 C 0 188
MIN -6.49 0.45 171 1.7 0 176
0 0.45 202 0 0.45 202 4.84 C 0.45 171

111 MAX 4.34 0 160 3.74 0 160

0 0 155 0 0 155 39.22 C 0 188
MIN 1.75 0.2 175 -2.02 0.2 175
0 0.2 202 0 0.2 202 2.31 C 0.2 171

119 MAX -3.15 0 165 7.42 0.45 159

0 0 155 0 0 155 39.22 C 0 188
MIN -5.94 0.45 167 1.1 0 178
0 0.45 202 0 0.45 202 2.31 C 0.45 171

122 MAX 5.14 0 172 4.08 0 172

0 0 155 0 0 155 39.19 C 0 188
MIN 1.26 0.45 163 0.62 0.45 175
0 0.45 202 0 0.45 202 1.81 C 0.45 171

115 MAX 0.66 0 160 -0.84 0.62 165

0 0 155 0 0 155 39.22 C 0 188
MIN -1.46 0.62 175 -3.15 0 167
0 0.62 202 0 0.62 202 2.31 C 0.62 171

1102 MAX 18.01 0 167 14.36 0 167

0 0 155 0 0 155 12.44 C 0 156
MIN 8.65 0.5 160 0.56 0.5 166
0 0.5 202 0 0.5 202 7.34 C 0.5 175

1402 MAX -4.32 0.5 159 2.41 0.5 163

0 0 155 0 0 155 13.52 C 0 155
MIN -15.9 0 168 -9.82 0 168
0 0.5 202 0 0.5 202 8.53 C 0.5 178

1105 MAX 6 0 167 -2.23 0 171

0 0 155 0 0 155 9.71 C 0 156
MIN -0.5 0.56 166 -8.53 0.56 187
0 0.56 202 0 0.56 202 5.24 C 0.56 175

1405 MAX 2.4 0.56 163 8.48 0.51 188

0 0 155 0 0 155 10.79 C 0 155
MIN -3.9 0 168 1.23 0 171
0 0.56 202 0 0.56 202 6.43 C 0.56 178

1109 MAX -2.31 0 171 3.06 0.5 164

0 0 155 0 0 155 5.94 C 0 156
MIN -8.42 0.5 164 -5.46 0 187
0 0.5 202 0 0.5 202 2.53 C 0.5 175

ULS_ENV 52
 1409 MAX 9.9 0.5 164 1.9 0 188
0 0 155 0 0 155 7.02 C 0 155
MIN 2.44 0 171 -6.88 0.5 163
0 0.5 202 0 0.5 202 3.72 C 0.5 178

1202 MAX 3.78 0 167 8.07 0 167

0 0 155 0 0 155 17 C 0 172
MIN 1.27 0.4 166 2.09 0.4 166
0 0.4 202 0 0.4 202 9.95 C 0.4 163

1302 MAX 2.89 0 163 5.74 0 163

0 0 155 0 0 155 17.98 C 0 171
MIN 0.35 0.4 172 0.11 0.4 174
0 0.4 202 0 0.4 202 10.58 C 0.4 164

1209 MAX 2.76 0 171 -1.45 0 165

0 0 155 0 0 155 11.66 C 0 172
MIN 0.37 0.4 164 -6.36 0.4 167
0 0.4 202 0 0.4 202 6C 0.4 163

1309 MAX 1.83 0 163 0.02 0.4 172

0 0 155 0 0 155 12.64 C 0 171
MIN -0.49 0.4 168 -4.81 0.4 163
0 0.4 202 0 0.4 202 6.63 C 0.4 164

3 MAX -4.99 0 165 0.37 0.59 160

0 0 155 0 0 155 1.34 T 0 165
MIN -8.43 0.59 167 -11.84 0 175
0 0.59 202 0 0.59 202 3.14 T 0.59 167

28 MAX 7.81 0 168 5.46 0 159

0 0 155 0 0 155 2.84 C 0 163
MIN 4.18 0.59 163 -7.03 0.59 168
0 0.59 202 0 0.59 202 1.03 C 0.59 172

103 MAX 3.35 0 156 2.74 0 164

0 0 155 0 0 155 39.83 C 0 188
MIN 0.34 0.61 171 -4.76 0.61 171
0 0.61 202 0 0.61 202 4.84 C 0.61 171

128 MAX -1.6 0 177 5.57 0.61 164

0 0 155 0 0 155 39.19 C 0 188
MIN -4.43 0.61 155 -2.01 0 171
0 0.61 202 0 0.61 202 1.81 C 0.61 171

1103 MAX 13.87 0 167 7.04 0 171

0 0 155 0 0 155 11.59 C 0 156
MIN 5.61 0.56 160 -4.27 0.56 164
0 0.56 202 0 0.56 202 6.64 C 0.56 175

1403 MAX -2.08 0.56 159 5.91 0.56 164

0 0 155 0 0 155 12.67 C 0 155
MIN -11.77 0 168 -3.94 0 172
0 0.56 202 0 0.56 202 7.83 C 0.56 178

ULS_ENV 53
STAAD OUTPUT FOR SLS DEAD LOAD + NO LIVE LOAD
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -6.1 0 307 -3.25 0.5 301

0 0 301 0 0 301 0.79 T 0 310
MIN -7.43 0.5 306 -8.87 0 306
0 0.5 312 0 0.5 312 1.54 T 0.5 302

29 MAX 7.44 0 304 -1.34 0 302

0 0 301 0 0 301 1.31 C 0 308
MIN 6.11 0.5 307 -8.05 0.5 306
0 0.5 312 0 0.5 312 0.58 C 0.5 301

5 MAX -1.33 0 301 2.57 0.59 301

0 0 301 0 0 301 0.79 T 0 310
MIN -2.72 0.59 308 0.14 0 308
0 0.59 312 0 0.59 312 1.54 T 0.59 302

26 MAX 2.35 0 310 3.62 0 302

0 0 301 0 0 301 1.31 C 0 308
MIN 0.63 0.59 302 0.84 0.59 312
0 0.59 312 0 0.59 312 0.58 C 0.59 301

9 MAX 4.3 0 301 0.75 0 308

0 0 301 0 0 301 0.79 T 0 310
MIN 2.77 0.5 308 -1.61 0.5 301
0 0.5 312 0 0.5 312 1.54 T 0.5 302

11 MAX -5.76 0 310 -3.17 0.2 310

0 0 301 0 0 301 0.23 C 0 301
MIN -6.52 0.2 302 -5.65 0 302
0 0.2 312 0 0.2 312 0.19 C 0.2 312

19 MAX 4.57 0 301 0.7 0 308

0 0 301 0 0 301 0.23 C 0 301
MIN 3.46 0.5 308 -2.23 0.5 301
0 0.5 312 0 0.5 312 0.19 C 0.5 312

22 MAX -3.66 0 310 0.03 0.5 309

0 0 301 0 0 301 1.31 C 0 308
MIN -5.45 0.5 302 -2.87 0 302
0 0.5 312 0 0.5 312 0.58 C 0.5 301

15 MAX -0.52 0 310 3.11 0.6 304

0 0 301 0 0 301 0.23 C 0 301
MIN -1.69 0.6 302 2.13 0 308
0 0.6 312 0 0.6 312 0.19 C 0.6 312

102 MAX 3.19 0 304 2.68 0 304

0 0 301 0 0 301 6.55 C 0 304
MIN 1.89 0.45 308 -0.33 0.45 301
0 0.45 312 0 0.45 312 2.95 C 0.45 307

129 MAX -2.23 0 307 3.72 0.45 304

0 0 301 0 0 301 7.04 C 0 304
MIN -3.49 0.45 306 0.58 0 301
0 0.45 312 0 0.45 312 3.43 C 0.45 307

SLS_ENV 54
 105 MAX 0.8 0 304 -0.6 0 310
0 0 301 0 0 301 6.55 C 0 304
MIN -0.67 0.61 302 -1.69 0.15 301
0 0.61 312 0 0.61 312 2.95 C 0.61 307

125 MAX 1.2 0 301 -0.37 0 310

0 0 301 0 0 301 7.04 C 0 304
MIN -0.25 0.61 312 -1.2 0.61 301
0 0.61 312 0 0.61 312 3.43 C 0.61 307

109 MAX -2.61 0 310 3.76 0.45 302

0 0 301 0 0 301 6.55 C 0 304
MIN -3.92 0.45 302 1.61 0 312
0 0.45 312 0 0.45 312 2.95 C 0.45 307

111 MAX 3.45 0 301 3.04 0 301

0 0 301 0 0 301 6.51 C 0 304
MIN 2.55 0.2 308 0.99 0.2 308
0 0.2 312 0 0.2 312 2.84 C 0.2 307

119 MAX -2.72 0 307 4.12 0.45 302

0 0 301 0 0 301 6.51 C 0 304
MIN -3.96 0.45 302 1.19 0 312
0 0.45 312 0 0.45 312 2.84 C 0.45 307

122 MAX 3.59 0 301 3.26 0 301

0 0 301 0 0 301 7.04 C 0 304
MIN 2.3 0.45 312 1.4 0.45 312
0 0.45 312 0 0.45 312 3.43 C 0.45 307

115 MAX 0.75 0 301 -0.89 0 307

0 0 301 0 0 301 6.51 C 0 304
MIN -0.67 0.62 308 -1.48 0.51 306
0 0.62 312 0 0.62 312 2.84 C 0.62 307

1102 MAX 13.88 0 310 7.7 0 302

0 0 301 0 0 301 9.27 C 0 304
MIN 6.27 0.5 301 1.34 0.5 312
0 0.5 312 0 0.5 312 7.97 C 0.5 308

1402 MAX -5.36 0.5 302 -0.49 0.5 310

0 0 301 0 0 301 9.57 C 0 304
MIN -13.4 0 312 -6.22 0 306
0 0.5 312 0 0.5 312 8.3 C 0.5 307

1105 MAX 3.06 0 308 -2.02 0 301

0 0 301 0 0 301 7.25 C 0 304
MIN -0.07 0.56 306 -6.33 0.56 312
0 0.56 312 0 0.56 312 5.87 C 0.56 308

1405 MAX 0.55 0.56 304 6.41 0.47 310

0 0 301 0 0 301 7.55 C 0 304
MIN -2.3 0 312 2.33 0 301
0 0.56 312 0 0.56 312 6.21 C 0.56 307

1109 MAX -2.52 0 307 2.06 0.5 304

0 0 301 0 0 301 4.46 C 0 304
MIN -6.34 0.5 306 -1.74 0 308
0 0.5 312 0 0.5 312 3.16 C 0.5 308

SLS_ENV 55
 1409 MAX 6.82 0.5 304 0.25 0 309
0 0 301 0 0 301 4.76 C 0 304
MIN 3 0 307 -3.06 0.5 306
0 0.5 312 0 0.5 312 3.49 C 0.5 307

1202 MAX 1.76 0 302 3.58 0 308

0 0 301 0 0 301 12.26 C 0 301
MIN 0.96 0.4 312 1.47 0.4 301
0 0.4 312 0 0.4 312 11.1 C 0.4 312

1302 MAX 1.08 0 308 1.99 0 302

0 0 301 0 0 301 12.44 C 0 302
MIN 0.32 0.4 301 0.1 0.4 312
0 0.4 312 0 0.4 312 11.06 C 0.4 312

1209 MAX 1.05 0 302 -0.9 0 310

0 0 301 0 0 301 8.3 C 0 301
MIN 0.14 0.4 312 -2.72 0.4 302
0 0.4 312 0 0.4 312 7.15 C 0.4 312

1309 MAX 0.38 0 308 0.17 0.4 301

0 0 301 0 0 301 8.49 C 0 302
MIN -0.5 0.4 301 -1.39 0.4 308
0 0.4 312 0 0.4 312 7.11 C 0.4 312

SLS_ENV 56
STAAD OUTPUT FOR SLS DEAD LOAD + LIVE LOAD (ACC)
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -6.33 0 329 -2.38 0.5 314

0 0 313 0 0 313 0.99 T 0 331
MIN -7.77 0.5 324 -12.72 0 320
0 0.5 344 0 0.5 344 2.07 T 0.5 317

29 MAX 7.82 0 323 1.42 0 313

0 0 313 0 0 313 1.78 C 0 329
MIN 6.13 0.5 329 -10.97 0.5 320
0 0.5 344 0 0.5 344 0.73 C 0.5 318

5 MAX -1.2 0 314 3.37 0.59 314

0 0 313 0 0 313 0.99 T 0 331
MIN -3.71 0.59 333 -2.93 0 333
0 0.59 344 0 0.59 344 2.07 T 0.59 317

26 MAX 3.01 0 335 5.4 0 313

0 0 313 0 0 313 1.78 C 0 329
MIN -0.1 0.59 313 -1.48 0.59 336
0 0.59 344 0 0.59 344 0.73 C 0.59 318

9 MAX 4.21 0 314 1.38 0 329

0 0 313 0 0 313 0.99 T 0 331
MIN 1.9 0.5 333 -1.65 0.5 318
0 0.5 344 0 0.5 344 2.07 T 0.5 317

11 MAX -5.27 0 331 -2.5 0.2 331

0 0 313 0 0 313 0.62 C 0 317
MIN -7.75 0.2 317 -8.05 0 317
0 0.2 344 0 0.2 344 0.08 T 0.2 332

19 MAX 5.18 0 318 1.91 0 329

0 0 313 0 0 313 0.62 C 0 317
MIN 2.67 0.5 329 -3.27 0.5 318
0 0.5 344 0 0.5 344 0.08 T 0.5 332

22 MAX -3.33 0 335 0.44 0.5 330

0 0 313 0 0 313 1.78 C 0 329
MIN -6.12 0.5 313 -3.59 0 317
0 0.5 344 0 0.5 344 0.73 C 0.5 318

15 MAX -0.64 0 331 3.48 0.6 315

0 0 313 0 0 313 0.62 C 0 317
MIN -2.03 0.6 317 1.38 0 333
0 0.6 344 0 0.6 344 0.08 T 0.6 332

102 MAX 3.52 0 315 4.28 0 315

0 0 313 0 0 313 41.03 C 0 323
MIN 1.05 0.45 333 -3.36 0.45 317
0 0.45 344 0 0.45 344 3.82 C 0.45 333

129 MAX -1.95 0 334 6.2 0.45 315

0 0 313 0 0 313 40.84 C 0 323
MIN -4.12 0.45 316 -0.92 0 317
0 0.45 344 0 0.45 344 2.18 C 0.45 333

SLS_ENV 57
 105 MAX 1.13 0 315 0.45 0 331
0 0 313 0 0 313 41.03 C 0 323
MIN -1.51 0.61 317 -3.64 0 317
0 0.61 344 0 0.61 344 3.82 C 0.61 333

125 MAX 1.49 0 318 0.59 0.61 331

0 0 313 0 0 313 40.84 C 0 323
MIN -0.87 0.61 332 -2.24 0.61 317
0 0.61 344 0 0.61 344 2.18 C 0.61 333

109 MAX -2.28 0 331 4.15 0.45 317

0 0 313 0 0 313 41.03 C 0 323
MIN -4.77 0.45 317 1.62 0 336
0 0.45 344 0 0.45 344 3.82 C 0.45 333

111 MAX 3.23 0 314 3.01 0 314

0 0 313 0 0 313 40.63 C 0 323
MIN 2.32 0.2 333 -0.52 0.2 333
0 0.2 344 0 0.2 344 2.07 C 0.2 333

119 MAX -2.93 0 330 5.3 0.45 313

0 0 313 0 0 313 40.63 C 0 323
MIN -4.18 0.45 317 0.59 0 336
0 0.45 344 0 0.45 344 2.07 C 0.45 333

122 MAX 3.87 0 318 2.95 0 318

0 0 313 0 0 313 40.84 C 0 323
MIN 1.68 0.45 332 1.12 0.45 336
0 0.45 344 0 0.45 344 2.18 C 0.45 333

115 MAX 0.54 0 314 -0.49 0.62 329

0 0 313 0 0 313 40.63 C 0 323
MIN -0.89 0.62 333 -2.53 0.36 320
0 0.62 344 0 0.62 344 2.07 C 0.62 333

1102 MAX 15.41 0 335 11.04 0 317

0 0 313 0 0 313 9.6 C 0 315
MIN 7.17 0.5 314 0.1 0.5 332
0 0.5 344 0 0.5 344 7.12 C 0.5 333

1402 MAX -4.26 0.5 313 1.37 0.5 331

0 0 313 0 0 313 10.19 C 0 315
MIN -14.55 0 336 -8.78 0 320
0 0.5 344 0 0.5 344 8.02 C 0.5 334

1105 MAX 4.59 0 333 -2.49 0 317

0 0 313 0 0 313 7.58 C 0 315
MIN -0.79 0.56 316 -7.29 0.56 340
0 0.56 344 0 0.56 344 5.03 C 0.56 333

1405 MAX 1.66 0.56 315 7.3 0.56 339

0 0 313 0 0 313 8.17 C 0 315
MIN -3.45 0 336 1.85 0 317
0 0.56 344 0 0.56 344 5.92 C 0.56 334

1109 MAX -2.17 0 333 3.58 0.5 315

0 0 313 0 0 313 4.79 C 0 315
MIN -7.06 0.5 316 -4.5 0 337
0 0.5 344 0 0.5 344 2.31 C 0.5 333

SLS_ENV 58
 1409 MAX 7.93 0.5 315 2.34 0 338
0 0 313 0 0 313 5.38 C 0 315
MIN 2.27 0 333 -5.45 0.5 316
0 0.5 344 0 0.5 344 3.21 C 0.5 334

1202 MAX 2.69 0 317 5.76 0 333

0 0 313 0 0 313 12.6 C 0 318
MIN 0.89 0.4 332 1.34 0.4 314
0 0.4 344 0 0.4 344 10.56 C 0.4 332

1302 MAX 1.82 0 329 3.7 0 313

0 0 313 0 0 313 13.22 C 0 317
MIN 0.1 0.4 318 -0.44 0.4 336
0 0.4 344 0 0.4 344 10.66 C 0.4 332

1209 MAX 1.98 0 317 -0.83 0 331

0 0 313 0 0 313 8.65 C 0 318
MIN 0.07 0.4 332 -4.59 0.4 317
0 0.4 344 0 0.4 344 6.61 C 0.4 332

1309 MAX 1.12 0 329 0.47 0.4 318

0 0 313 0 0 313 9.27 C 0 317
MIN -0.72 0.4 318 -2.88 0.4 329
0 0.4 344 0 0.4 344 6.7 C 0.4 332

SLS_ENV 59
STAAD OUTPUT FOR SLS DEAD LOAD + LIVE LOAD (LEAD)
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -6.1 0 307 -2.38 0.5 314

0 0 307 0 0 307 0.79 T 0 310
MIN -7.77 0.5 324 -12.72 0 320
0 0.5 345 0 0.5 345 2.07 T 0.5 317

29 MAX 7.82 0 323 1.42 0 313

0 0 307 0 0 307 1.84 C 0 345
MIN 6.11 0.5 307 -10.97 0.5 320
0 0.5 345 0 0.5 345 0.58 C 0.5 307

5 MAX -1.2 0 314 3.37 0.59 314

0 0 307 0 0 307 0.79 T 0 310
MIN -3.71 0.59 333 -2.93 0 333
0 0.59 345 0 0.59 345 2.07 T 0.59 317

26 MAX 3.01 0 335 5.4 0 313

0 0 307 0 0 307 1.84 C 0 345
MIN -0.1 0.59 313 -1.48 0.59 336
0 0.59 345 0 0.59 345 0.58 C 0.59 307

9 MAX 4.23 0 307 1.38 0 329

0 0 307 0 0 307 0.79 T 0 310
MIN 1.9 0.5 333 -1.65 0.5 318
0 0.5 345 0 0.5 345 2.07 T 0.5 317

11 MAX -5.27 0 331 -2.5 0.2 331

0 0 307 0 0 307 0.62 C 0 317
MIN -7.75 0.2 317 -8.05 0 317
0 0.2 345 0 0.2 345 0.08 T 0.2 332

19 MAX 5.18 0 318 1.91 0 329

0 0 307 0 0 307 0.62 C 0 317
MIN 2.67 0.5 329 -3.27 0.5 318
0 0.5 345 0 0.5 345 0.08 T 0.5 332

22 MAX -3.33 0 335 0.44 0.5 330

0 0 307 0 0 307 1.84 C 0 345
MIN -6.12 0.5 313 -3.59 0 317
0 0.5 345 0 0.5 345 0.58 C 0.5 307

15 MAX -0.52 0 310 3.48 0.6 315

0 0 307 0 0 307 0.62 C 0 317
MIN -2.03 0.6 317 1.38 0 333
0 0.6 345 0 0.6 345 0.08 T 0.6 332

102 MAX 3.52 0 315 4.28 0 315

0 0 307 0 0 307 41.03 C 0 323
MIN 1.05 0.45 333 -3.36 0.45 317
0 0.45 345 0 0.45 345 2.95 C 0.45 307

129 MAX -1.95 0 334 6.2 0.45 315

0 0 307 0 0 307 40.84 C 0 323
MIN -4.12 0.45 316 -0.92 0 317
0 0.45 345 0 0.45 345 2.18 C 0.45 333

SLS_ENV 60
 105 MAX 1.13 0 315 0.45 0 331
0 0 307 0 0 307 41.03 C 0 323
MIN -1.51 0.61 317 -3.64 0 317
0 0.61 345 0 0.61 345 2.95 C 0.61 307

125 MAX 1.49 0 318 0.59 0.61 331

0 0 307 0 0 307 40.84 C 0 323
MIN -0.87 0.61 332 -2.24 0.61 317
0 0.61 345 0 0.61 345 2.18 C 0.61 333

109 MAX -2.28 0 331 4.15 0.45 317

0 0 307 0 0 307 41.03 C 0 323
MIN -4.77 0.45 317 1.61 0 312
0 0.45 345 0 0.45 345 2.95 C 0.45 307

111 MAX 3.36 0 307 3.01 0 314

0 0 307 0 0 307 40.63 C 0 323
MIN 2.32 0.2 333 -0.52 0.2 333
0 0.2 345 0 0.2 345 2.07 C 0.2 333

119 MAX -2.72 0 307 5.3 0.45 313

0 0 307 0 0 307 40.63 C 0 323
MIN -4.25 0.45 345 0.59 0 336
0 0.45 345 0 0.45 345 2.07 C 0.45 333

122 MAX 3.87 0 318 3.2 0 307

0 0 307 0 0 307 40.84 C 0 323
MIN 1.68 0.45 332 1.12 0.45 336
0 0.45 345 0 0.45 345 2.18 C 0.45 333

115 MAX 0.73 0 307 -0.49 0.62 329

0 0 307 0 0 307 40.63 C 0 323
MIN -0.96 0.62 345 -2.53 0.36 320
0 0.62 345 0 0.62 345 2.07 C 0.62 333

1102 MAX 15.41 0 335 11.04 0 317

0 0 307 0 0 307 9.6 C 0 315
MIN 6.27 0.5 307 0.1 0.5 332
0 0.5 345 0 0.5 345 7.12 C 0.5 333

1402 MAX -4.26 0.5 313 1.37 0.5 331

0 0 307 0 0 307 10.19 C 0 315
MIN -14.55 0 336 -8.78 0 320
0 0.5 345 0 0.5 345 8.02 C 0.5 334

1105 MAX 4.59 0 333 -2.05 0 307

0 0 307 0 0 307 7.58 C 0 315
MIN -0.79 0.56 316 -7.29 0.56 340
0 0.56 345 0 0.56 345 5.03 C 0.56 333

1405 MAX 1.66 0.56 315 7.3 0.56 339

0 0 307 0 0 307 8.17 C 0 315
MIN -3.45 0 336 1.85 0 317
0 0.56 345 0 0.56 345 5.92 C 0.56 334

1109 MAX -2.17 0 333 3.58 0.5 315

0 0 307 0 0 307 4.79 C 0 315
MIN -7.06 0.5 316 -4.5 0 337
0 0.5 345 0 0.5 345 2.31 C 0.5 333

SLS_ENV 61
 1409 MAX 7.93 0.5 315 2.34 0 338
0 0 307 0 0 307 5.38 C 0 315
MIN 2.27 0 333 -5.45 0.5 316
0 0.5 345 0 0.5 345 3.21 C 0.5 334

1202 MAX 2.69 0 317 5.76 0 333

0 0 307 0 0 307 12.6 C 0 318
MIN 0.89 0.4 332 1.34 0.4 314
0 0.4 345 0 0.4 345 10.56 C 0.4 332

1302 MAX 1.82 0 329 3.7 0 313

0 0 307 0 0 307 13.22 C 0 317
MIN 0.1 0.4 318 -0.44 0.4 336
0 0.4 345 0 0.4 345 10.66 C 0.4 332

1209 MAX 1.98 0 317 -0.83 0 331

0 0 307 0 0 307 8.65 C 0 318
MIN 0.07 0.4 332 -4.59 0.4 317
0 0.4 345 0 0.4 345 6.61 C 0.4 332

1309 MAX 1.12 0 329 0.47 0.4 318

0 0 307 0 0 307 9.27 C 0 317
MIN -0.72 0.4 318 -2.88 0.4 329
0 0.4 345 0 0.4 345 6.7 C 0.4 332

SLS_ENV 62
STAAD OUTPUT FOR QP DEAD LOAD + NO LIVE LOAD
MEMB FY/ DIST LD MZ/ DIST LD
FZ DIST LD MY DIST LD FX DIST LD

2 MAX -6.14 0 404 -2.11 0.5 404

0 0 401 0 0 401 0.73 T 0 405
MIN -7.61 0.5 409 -10.56 0 407
0 0.5 410 0 0.5 410 0.92 T 0.5 406

29 MAX 7.62 0 409 -1.25 0 404

0 0 401 0 0 401 0.67 C 0 405
MIN 6.15 0.5 404 -9.74 0.5 407
0 0.5 410 0 0.5 410 0.48 C 0.5 406

5 MAX -1.04 0 404 3.31 0.59 404

0 0 401 0 0 401 0.73 T 0 405
MIN -3.09 0.59 407 -1.06 0 407
0 0.59 410 0 0.59 410 0.92 T 0.59 406

26 MAX 2.76 0 407 3.76 0 404

0 0 401 0 0 401 0.67 C 0 405
MIN 0.71 0.59 404 -0.46 0.59 407
0 0.59 410 0 0.59 410 0.48 C 0.59 406

9 MAX 4.5 0 404 0.66 0 405

0 0 401 0 0 401 0.73 T 0 405
MIN 2.87 0.5 407 -1.84 0.5 406
0 0.5 410 0 0.5 410 0.92 T 0.5 406

11 MAX -5.5 0 405 -2.65 0.2 405

0 0 401 0 0 401 0.43 C 0 406
MIN -6.67 0.2 406 -5.69 0 406
0 0.2 410 0 0.2 410 0.06 C 0.2 405

19 MAX 5 0 406 0.6 0 405

0 0 401 0 0 401 0.43 C 0 406
MIN 3.58 0.5 405 -3.07 0.5 406
0 0.5 410 0 0.5 410 0.06 C 0.5 405

22 MAX -3.43 0 407 0.26 0.5 405

0 0 401 0 0 401 0.67 C 0 405
MIN -5.05 0.5 404 -2.51 0 406
0 0.5 410 0 0.5 410 0.48 C 0.5 406

15 MAX -0.49 0 405 3.3 0.6 405

0 0 401 0 0 401 0.43 C 0 406
MIN -1.36 0.6 406 2.02 0 406
0 0.6 410 0 0.6 410 0.06 C 0.6 405

102 MAX 3.43 0 405 3.7 0 405

0 0 401 0 0 401 23.62 C 0 409
MIN 1.63 0.45 406 -1.67 0.45 406
0 0.45 410 0 0.45 410 2.28 C 0.45 406

129 MAX -1.93 0 406 4.74 0.45 405

0 0 401 0 0 401 24.11 C 0 409
MIN -3.73 0.45 405 -0.77 0 406
0 0.45 410 0 0.45 410 2.76 C 0.45 406

QP_ENV 63
 105 MAX 1.04 0 405 -0.02 0 405
0 0 401 0 0 401 23.62 C 0 409
MIN -0.99 0.61 406 -2.59 0 406
0 0.61 410 0 0.61 410 2.28 C 0.61 406

125 MAX 1.55 0 406 -0.05 0.61 405

0 0 401 0 0 401 24.11 C 0 409
MIN -0.48 0.61 405 -1.91 0.61 406
0 0.61 410 0 0.61 410 2.76 C 0.61 406

109 MAX -2.44 0 405 3.7 0.45 406

0 0 401 0 0 401 23.62 C 0 409
MIN -4.25 0.45 406 1.57 0 407
0 0.45 410 0 0.45 410 2.28 C 0.45 406

111 MAX 3.45 0 404 3.39 0 404

0 0 401 0 0 401 23.57 C 0 409
MIN 3.16 0.2 407 1.5 0.2 407
0 0.2 410 0 0.2 410 1.87 C 0.2 406

119 MAX -2.78 0 404 3.31 0.45 404

0 0 401 0 0 401 23.57 C 0 409
MIN -3.43 0.45 407 0.72 0 407
0 0.45 410 0 0.45 410 1.87 C 0.45 406

122 MAX 3.94 0 406 3.35 0 406

0 0 401 0 0 401 24.11 C 0 409
MIN 2.14 0.45 405 1.36 0.45 407
0 0.45 410 0 0.45 410 2.76 C 0.45 406

115 MAX 0.75 0 404 -0.58 0 404

0 0 401 0 0 401 23.57 C 0 409
MIN -0.13 0.62 407 -1.99 0.51 407
0 0.62 410 0 0.62 410 1.87 C 0.62 406

1102 MAX 14.55 0 407 8.79 0 407

0 0 401 0 0 401 9.5 C 0 405
MIN 5.81 0.5 404 0.59 0.5 405
0 0.5 410 0 0.5 410 7.72 C 0.5 406

1402 MAX -5.33 0.5 404 0.26 0.5 405

0 0 401 0 0 401 9.81 C 0 405
MIN -14.07 0 407 -7.7 0 407
0 0.5 410 0 0.5 410 8.03 C 0.5 406

1105 MAX 3.45 0 407 -1.63 0 406

0 0 401 0 0 401 7.48 C 0 405
MIN -0.52 0.56 405 -6.77 0.56 409
0 0.56 410 0 0.56 410 5.63 C 0.56 406

1405 MAX 1.01 0.56 405 6.82 0.51 409

0 0 401 0 0 401 7.79 C 0 405
MIN -2.97 0 407 1.94 0 406
0 0.56 410 0 0.56 410 5.93 C 0.56 406

1109 MAX -1.85 0 406 3.03 0.5 405

0 0 401 0 0 401 4.69 C 0 405
MIN -6.79 0.5 405 -2.15 0 409
0 0.5 410 0 0.5 410 2.91 C 0.5 406

QP_ENV 64
 1409 MAX 7.28 0.5 405 1.38 0 409
0 0 401 0 0 401 5C 0 405
MIN 2.33 0 406 -4.04 0.5 405
0 0.5 410 0 0.5 410 3.22 C 0.5 406

1202 MAX 1.34 0 406 2.65 0 407

0 0 401 0 0 401 12.61 C 0 406
MIN 0.76 0.4 405 1.07 0.4 404
0 0.4 410 0 0.4 410 11.05 C 0.4 405

1302 MAX 0.61 0 405 0.79 0 404

0 0 401 0 0 401 12.56 C 0 406
MIN 0.03 0.4 406 -0.48 0.4 407
0 0.4 410 0 0.4 410 11 C 0.4 405

1209 MAX 0.64 0 406 -0.59 0 405

0 0 401 0 0 401 8.65 C 0 406
MIN -0.06 0.4 405 -1.92 0.4 406
0 0.4 410 0 0.4 410 7.1 C 0.4 405

1309 MAX -0.1 0 405 0.75 0.4 406

0 0 401 0 0 401 8.61 C 0 406
MIN -0.79 0.4 406 -0.64 0 405
0 0.4 410 0 0.4 410 7.05 C 0.4 405

QP_ENV 65
STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 13-Apr-19
END JOB INFORMATION
* Model for 3 Cell x 5m span x 4.825m Effective height
UNIT METER MTON

JOINT COORDINATES
*RAFT COORDINATE
1 0 0 0 13 0 0 12
R 10 0.5 0 0
R 10 0.5 0 0
R 10 0.5 0 0

*DECK SLAB COORDINATE

1001 0 4.825 0 1013 0 4.825 12
R 30 0.5 0 0
*FIRST WALL COORDINATE
2001 0 0.4825 0 2013 0 0.4825 12
R 8 0 0.4825 0
*SECOND WALL COORDINATE
2201 5 0.4825 0 2213 5 0.4825 12
R 8 0 0.4825 0
*THIRD WALL COORDINATE
2401 10 0.4825 0 2413 10 0.4825 12
R 8 0 0.4825 0
*FOURTH COORDINATE
2601 15 0.4825 0 2613 15 0.4825 12
R 8 0 0.4825 0

MEMBER INCIDENCES
*RAFT MEMBERS
1 1 2 12
R 30 12 13
501 1 14 530 1 13
R 12 30 1

*SLAB MEMBERS
5001 1001 1002 5012
R 30 12 13
5501 1001 1014 5530 1 13
R 12 30 1

*Z MEMBER FIRST WALL

3001 2001 2002 3012
R 8 12 13
*Z MEMBER SECOND WALL
3201 2201 2202 3212

LL_Staad Page 66
R 8 12 13
*Z MEMBER THIRD WALL
3401 2401 2402 3412
R 8 12 13
*Z MEMBER FOURTH WALL
3601 2601 2602 3612
R 8 12 13

*Y MEMBER FIRST WALL

4001 1 2001 4121 10 1
4002 2001 2014 4009 1 13
R 12 10 1
4010 2105 1001 4130 10 1

*Y MEMBER SECOND WALL

4201 131 2201 4321 10 1
4202 2201 2214 4209 1 13
R 12 10 1
4210 2305 1131 4330 10 1

*Y MEMBER THIRD WALL

4401 261 2401 4521 10 1
4402 2401 2414 4409 1 13
R 12 10 1
4410 2505 1261 4530 10 1

*Y MEMBER FOURTH WALL

4601 391 2601 4721 10 1
4602 2601 2614 4609 1 13
R 12 10 1
4610 2705 1391 4730 10 1

START GROUP DEFINITION

MEMBER
_01_Raft_E_SUP 501 TO 861 BY 30 530 TO 890 BY 30
_02_Raft_E_SPAN 504 TO 864 BY 30 526 TO 886 BY 30
_03_RAFT_I_SUP 510 TO 870 BY 30 511 TO 871 BY 30 -
520 TO 880 BY 30 521 TO 881 BY 30
_04_Raft_I_SPAN 515 TO 875 BY 30 516 TO 876 BY 30
_05_Raft_E_SUP 5501 TO 5861 BY 30 5530 TO 5890 BY 30
_06_Raft_E_SPAN 5504 TO 5864 BY 30 5526 TO 5886 BY 30
_07_RAFT_I_SUP 5510 TO 5870 BY 30 5511 TO 5871 BY 30 -
5520 TO 5880 BY 30 5521 TO 5881 BY 30
_08_Raft_I_SPAN 5515 TO 5875 BY 30 5516 TO 5876 BY 30
_07_EWALL_BOT 4001 TO 4121 BY 10 4601 TO 4721 BY 10
_08_EWALL_MID 4005 TO 4125 BY 10 4605 TO 4725 BY 10 -
4006 TO 4126 BY 10 4606 TO 4726 BY 10
_09_EWALL_TOP 4010 TO 4120 BY 10 4610 TO 4720 BY 10

LL_Staad Page 67
_10_IWALL_BOT 4201 TO 4321 BY 10 4401 TO 4521 BY 10
_11_IWALL_TOP 4210 TO 4320 BY 10 4410 TO 4520 BY 10

_RAFTZ1 1 TO 12 361 to 372

_RAFTZ2 13 TO 360
_RAFTX1 501 TO 530 861 TO 890
_RAFTX2 531 TO 860
_SLABZ1 5001 TO 5012 5361 TO 5372
_SLABZ2 5013 TO 5360
_SLABX1 5501 TO 5530 5861 TO 5890
_SLABX2 5531 TO 5860
_WALLZ1 3001 TO 3108
_WALLZ2 3201 TO 3308
_WALLZ3 3401 TO 3508
_WALLZ4 3601 TO 3708

_WALLY11 4001 TO 4010 4121 TO 4130

_WALLY12 4011 TO 4120
_WALLY21 4201 TO 4210 4321 TO 4330
_WALLY22 4211 TO 4320
_WALLY31 4401 TO 4410 4521 TO 4530
_WALLY32 4411 TO 4520
_WALLY41 4601 TO 4610 4721 TO 4730
_WALLY42 4611 TO 4720

END GROUP DEFINITION

DEFINE MATERIAL START

ISOTROPIC CONCRETE
E 3.1623e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1e-005
DAMP 0.05

ISOTROPIC CONC0
E 3.1623e+006
POISSON 0.17
DENSITY 0
ALPHA 1e-005
DAMP 0.05

END DEFINE MATERIAL

CONSTANTS

MATERIAL CONCRETE ALL

LL_Staad Page 68
MATERIAL CONC0 MEMB _RAFTZ1
MATERIAL CONC0 MEMB _RAFTZ2
MATERIAL CONC0 MEMB _SLABZ1
MATERIAL CONC0 MEMB _SLABZ2
MATERIAL CONC0 MEMB _WALLZ1
MATERIAL CONC0 MEMB _WALLZ2
MATERIAL CONC0 MEMB _WALLZ3
MATERIAL CONC0 MEMB _WALLZ4

MEMBER PROPERTY INDIAN

_RAFTZ1 PRIS YD 0.5 ZD 0.5

_RAFTZ2 PRIS YD 0.5 ZD 1.0
_RAFTX1 PRIS YD 0.5 ZD 0.5
_RAFTX2 PRIS YD 0.5 ZD 1.0

_WALLZ1 PRIS YD 0.5 ZD 0.4825

_WALLZ2 PRIS YD 0.4 ZD 0.4825
_WALLZ3 PRIS YD 0.4 ZD 0.4825
_WALLZ4 PRIS YD 0.5 ZD 0.4825

_WALLY11 PRIS YD 0.5 ZD 0.5

_WALLY12 PRIS YD 0.5 ZD 1.0
_WALLY21 PRIS YD 0.4 ZD 0.5
_WALLY22 PRIS YD 0.4 ZD 1.0
_WALLY31 PRIS YD 0.4 ZD 0.5
_WALLY32 PRIS YD 0.4 ZD 1.0
_WALLY41 PRIS YD 0.5 ZD 0.5
_WALLY42 PRIS YD 0.5 ZD 1.0

_SLABZ1 PRIS YD 0.45 ZD 0.5

_SLABZ2 PRIS YD 0.45 ZD 1.0
_SLABX1 PRIS YD 0.45 ZD 0.5
_SLABX2 PRIS YD 0.45 ZD 1.0

SUPPORTS
2 TO 12 14 TO 390 392 TO 402 ELASTIC MAT DIRECT YONLY SUBGRADE 750
1 13 391 403 FIXED BUT MX MY MZ KFY 750

DEFINE MOVING LOAD

* CLASS A IMPACT FACTOR 43% 15% Congestion Factor 1.58
TYPE 1 LOAD 5.372 5.372 5.372 5.372 9.006 9.006 2.133 2.133
DIST 3 3 3 4.3 1.2 3.2 1.1
* CLASS 70R WHEEL 25% 15% Congestion Factor 1.4
TYPE 2 LOAD 5.6 8.4 8.4 11.9 11.9 11.9 11.9
DIST 3.96 1.52 2.13 1.37 3.05 1.37
* CLASS 70R TRACK 25% 15% Congestion Factor 1.4
TYPE 3 LOAD 10*4.9

LL_Staad Page 69
DIST 0.508 0.508 0.508 0.508 0.508 0.508 0.508 0.508 0.508

* THREE CLASS A MOVING IN X DIRECTION

LOAD GENERATION 67
TYPE 1 -18.8 4.825 0.9 XINC 0.5
TYPE 1 -18.8 4.825 2.7 XINC 0.5
TYPE 1 -18.8 4.825 4.4 XINC 0.5
TYPE 1 -18.8 4.825 6.2 XINC 0.5
TYPE 1 -18.8 4.825 7.9 XINC 0.5
TYPE 1 -18.8 4.825 9.7 XINC 0.5

* ONE CLASS 70 R l + CLASS A MOVING IN X DIRECTION

LOAD GENERATION 67
TYPE 1 -18.8 4.825 0.9 XINC 0.5
TYPE 1 -18.8 4.825 2.7 XINC 0.5

TYPE 2 -13.4 4.825 4.4 XINC 0.5

TYPE 2 -13.4 4.825 6.33 XINC 0.5

* ONE 70R TRACK LOAD MOVING IN X DIRECTION

LOAD GENERATION 67
TYPE 1 -18.8 4.825 0.9 XINC 0.5
TYPE 1 -18.8 4.825 2.7 XINC 0.5

TYPE 3 -8.45 4.825 4.4 XINC 0.5

TYPE 3 -8.45 4.825 6.33 XINC 0.5

PERFORM ANALYSIS

FINISH

LL_Staad Page 70
 STAAD OUTPUT FOR LIVE LOAD

7.732 7.732

4.827 4.827

3.57 4.657

6.972 6.716 6.972

4.109 2.05 4.109 5.643

5.681 5.681

7.194 7.194

Typical Unfactored Bending Moment Envolupe for Live Load (T-m)

Axial
Shear-Y Shear-Z Torsion Moment-Y Moment-Z
Beam L/C Node Force
Mton Mton MTon-m MTon-m MTon-m
MTon
531 12 2 1.351 -6.804 -0.503 -0.212 0.105 -5.681
556 172 327 -0.038 0.649 -0.164 0.332 0.012 4.109
550 167 262 0.032 -5.212 -0.394 -0.232 -0.134 7.194
546 39 197 0.808 0.125 -0.013 0.082 0.006 2.05

5651 153 1006 1.27 8.906 0.606 0.115 0.005 4.827

5594 150 1056 -0.187 -4.57 0.269 -0.223 -0.024 6.972
5671 173 1266 0.158 10.044 1.041 0.167 -0.344 7.732
5605 161 1199 -1.221 -4.011 0.003 -0.531 -0.038 6.716

4011 12 2 7.728 1.519 0.906 0.037 -0.528 5.643

4615 172 2641 7.659 -0.478 1.494 -0.366 -0.424 -3.122
4060 153 1006 -8.829 1.325 -0.669 -0.165 -0.183 -4.657

4511 146 272 -1.47 -1.26 0.434 0.041 -0.369 -2.876

4260 163 1136 -9.806 1.503 -0.287 0.086 -0.103 -3.57
 SUMMARY OF LIVE LOAD BM (T-m)
ULS BM SLS BM ULS SF
BM(LL) LL(Lead) LL(Acc) LL(Lead) LL(Acc) LL(Lead) LL(Acc)
End Support 4.827 7.2405 5.55105 4.827 3.62025 9.641 7.391
DECK End Span 6.972 10.458 8.0178 6.972 5.229
SLAB Int Support 7.732 11.598 8.8918 7.732 5.799
Int Span 6.716 10.074 7.7234 6.716 5.037

End Support 5.681 8.5215 6.53315 5.681 4.26075 5.612 4.302

RAFT End Span 4.109 6.1635 4.72535 4.109 3.08175
SLAB Int Support 7.194 10.791 8.2731 7.194 5.3955
Int Span 2.05 3.075 2.3575 2.05 1.5375

End Wall Bottom 5.643 8.4645 6.48945 5.643 4.23225 2.165 1.659
END WALL End Wall Mid 3.122 4.683 3.5903 3.122 2.3415
End Wall Top 4.657 6.9855 5.35555 4.657 3.49275
Int Wall Bottom 2.876 4.314 3.3074 2.876 2.157
INT WALL
Int Wall Top 3.57 5.355 4.1055 3.57 2.6775
STAAD PLANE
START JOB INFORMATION
ENGINEER DATE 13-Apr-19
END JOB INFORMATION

UNIT METER MTON

JOINT COORDINATES
* Model for 3 Cell x 5m span x 4.825m Effective height

1 0 0 0;
R 1 0.25 0 0 ; R 1 0.5 0 0 ; R 6 0.59167 0 0 ; R 1 0.5 0 0 ; R 1 0.2 0 0
R 1 0.2 0 0 ; R 1 0.5 0 0 ; R 6 0.6 0 0 ; R 1 0.5 0 0 ; R 1 0.2 0 0
R 1 0.25 0 0 ; R 1 0.5 0 0 ; R 6 0.59167 0 0 ; R 1 0.5 0 0 ; R 1 0.2 0 0

1001 0 4.825 0
R 1 0.25 0 0 ; R 1 0.45 0 0 ; R 6 0.60833 0 0 ; R 1 0.45 0 0 ; R 1 0.2 0 0
R 1 0.2 0 0 ; R 1 0.45 0 0 ; R 6 0.61667 0 0 ; R 1 0.45 0 0 ; R 1 0.2 0 0
R 1 0.2 0 0 ; R 1 0.45 0 0 ; R 6 0.60833 0 0 ; R 1 0.45 0 0 ; R 1 0.25 0 0

2001 0 0.25 0
R 1 0 0.5 0 ; R 6 0 0.558 0 ; R 1 0 0.5 0
2201 5 0.2 0
R 1 0 0.4 0 ; R 6 0 0.592 0 ; R 1 0 0.4 0
2401 10 0.2 0
R 1 0 0.4 0 ; R 6 0 0.592 0 ; R 1 0 0.4 0
2601 15 0.25 0
R 1 0 0.5 0 ; R 6 0 0.558 0 ; R 1 0 0.5 0

MEMBER INCIDENCES

1 1 2 30
101 1001 1002 130
1101 1 2001; 1102 2001 2002 1109; 1110 2009 1001
1201 11 2201; 1202 2201 2202 1209; 1210 2209 1011
1301 21 2401; 1302 2401 2402 1309; 1310 2409 1021
1401 31 2601; 1402 2601 2602 1409; 1410 2609 1031

START GROUP DEFINITION

MEMBER
_sRaft 3 8 13 18 23 28
_sSlab 103 108 113 118 123 128
_sWall 1103 1108 1203 1208 1303 1308 1403 1408
_RAFT 1 TO 30
_SLAB 101 TO 130
_WALL1 1101 TO 1110
_WALL2 1201 TO 1210
_WALL3 1301 TO 1310
_WALL4 1401 TO 1410
END GROUP DEFINITION

DEFINE MATERIAL START

ISOTROPIC CONCRETE
E 3.1623e+006
POISSON 0.17
DENSITY 2.5
ALPHA 1.2e-005
DAMP 0.05
END DEFINE MATERIAL

CONSTANTS
MATERIAL CONCRETE ALL

MEMBER PROPERTY INDIAN

_RAFT PRIS YD 0.5 ZD 12.0
_WALL1 PRIS YD 0.5 ZD 12.0
_WALL2 PRIS YD 0.4 ZD 12.0
_WALL3 PRIS YD 0.4 ZD 12.0
_WALL4 PRIS YD 0.5 ZD 12.0
_SLAB PRIS YD 0.45 ZD12.0

SUPPORTS
1 31 FIXED BUT MX MY MZ FZ KFY 375
2 30 FIXED BUT MX MY MZ FX FZ KFY 750
3 9 13 19 23 29 FIXED BUT MX MY MZ FX FZ KFY 818.7525
4 TO 8 14 to 18 24 TO 28 FIXED BUT MX MY MZ FX FZ KFY 887.505
10 12 20 22 FIXED BUT MX MY MZ FX FZ KFY 675
11 21 FIXED BUT MX MY MZ FX FZ KFY 600

DEFINE MOVING LOAD

* CLASS A IMPACT FACTOR 43% 15% Congestion Factor 1.58
TYPE 1 LOAD 5.372 5.372 5.372 5.372 9.006 9.006 2.133 2.133
DIST 3 3 3 4.3 1.2 3.2 1.1
* CLASS 70R WHEEL 25% 15% Congestion Factor 1.4
TYPE 2 LOAD 5.6 8.4 8.4 11.9 11.9 11.9 11.9
DIST 3.96 1.52 2.13 1.37 3.05 1.37
* CLASS 70R TRACK 25% 15% Congestion Factor 1.4
TYPE 3 LOAD 10*4.9
DIST 0.508 0.508 0.508 0.508 0.508 0.508 0.508 0.508 0.508

* THREE CLASS A MOVING IN X DIRECTION

LOAD GENERATION 67
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5

* ONE CLASS 70 R l + CLASS A MOVING IN X DIRECTION

LOAD GENERATION 67
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 2 -13.4 4.825 0 XINC 0.5
TYPE 2 -13.4 4.825 0 XINC 0.5

* ONE 70R TRACK LOAD MOVING IN X DIRECTION

LOAD GENERATION 67
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 1 -18.8 4.825 0 XINC 0.5
TYPE 2 -8.45 4.825 0 XINC 0.5
TYPE 2 -8.45 4.825 0 XINC 0.5

PERFORM ANALYSIS

FINISH

Axial Force Shear-Y Shear-Z Torsion Moment-Y Moment-Z

Beam L/C Node
Mton Mton Mton MTon-m MTon-m MTon-m
3 12 3 0.471 -44.892 0 0 0 -14.859
108 18 1009 -9.422 77.121 0 0 0 15.771
1108 12 2007 80.532 17.316 0 0 0 1.565

Per meter
Shear-Y
Beam Shear-Y
Mton
Remark Mton
8 Raft -44.892 3.741 Considering 12m width
113 Slab 77.121 6.427
1108 Wall 17.316 1.443
 BOX OPENING 3 X 4500 X 4350 mm
Bar Bar
Shape of Bars Spacing Length
Mark Diameter
Remark
a 12 100 14420 14420 Slab Bottom
b 12 200 15320 450 + 14420 + 450 Slab Top

c 12 200 3170
1585 + 1585 Slab top end

d 12 100 6025
420 + 5185 + 420 End wall exterior

d1 12 100 5185
5185 End wall Interior

d2 12 200 6025 Interior wall

420 + 5185 + 420 exterior

d3 12 200 5185 interior wall

5185 Interior

e 16 200 3170
1585 + 1585 Raft Bottom end

e1 12 200 3170 Raft Bottom

1585 + 1585 Interior support

e2 12 200 3170 Slab top Interior

1585 + 1585 support
f 12 150 14420 9920 Raft Top
g 12 200 15320 450 + 14420 + 450 Raft Bottom
h 10 200 1248
200 + 848 + 200 Haunch bar
i 8 150 15920 15920 Dist steel Raft
i2 8 200 15920 15920 Dist steel Slab
i1 8 100 15920 15920 Dist steel Wall
HAUNCH SIZE 100 X 300 mm
End wall T1 = 500 mm Interior wall T2 = 400 mm Concrete 366.48
Slab = 450 mm Raft = 500 mm Steel 19412
kg/m^3 52.97