ROCK TYPES DESCRIPTION

Notes on Sample Examination & Description

1- Sand/Sandstone:
1. Rock Type.
 SandSD
 Sandstone SST
2. Colour/transparency – use colour charts
 transparent transp
 translucent transl
 opaque opq
The grains can also have colours. Eg. Greyish pink translucent.
3. Grain Size
 1.000-2.000mm Very course v crs
 0.500-1.000mm Coarse crs
 0.250-0.500mm Medium med
 0.250-0.125mm Fine f
 Just able to see grains = very fine v f
4. Sorting
 Very poorly sorted v ply srt
 Poorly sorted ply srt
 Moderately sorted
 Well sorted w srt
 Very well sorted v w srt
5. Roundness
This is how sharp the edges of the grains are.
 Rounded rnd
 Sub rounded sb rnd
 Sub angular sb ang
 Angular ang

Rounded Sub Rounded Sub Angular Angular

6. Sphericity
 Elongate elg
 Sub elongate sb elg
 Sub spherical sb sph
 Spherical sph
7. Cement and matrix.
Cement is deposited chemically and matrix mechanically
1st put the type of cement/matrix.
 Calcareous calc
 Dolomitic dol
 Anhydritic anhy
 Gypsiferous gyp
 Siliceous.silc
2
2nd put degree of cement
 Unconsolidated uncons
 Poorly cemented p cmt
 Moderately cemented mo cmt
 Well cemented w cmt
 Quartzitic qtzc
Eg. Predominantly well cemented, occasionally poorly cemented.
8. Hardness/induration.
 Loose lse
 Friable fri
 Moderately hard mo hd
 Hardhd
 Very hard v hd
9. Accessories
 Chert cht
 Glauconite glauc
 Lignite lig
 Muscovite musc
 Pyrite pyr
 Sulphurs
 Hematite heam
How the accessory mineral is distributed may also be described.
Eg. Fine disseminated pyrite of loose pyrite nodules.
10. Porosity
This is the gaps between the grains.
 None – grains are tight together n v p
 Poor intergranular porosity – pores are not connected p v p
 Fair intergranular porosity – pores present within grains fr v p
 Good intergranular porosity – Some pores between grains are connected
 Excellent intergranular porosity – All pores are connected ex v p
11- OIL SHOWS.
ALWAYS describe the degree of show whether there is a SHOW or NOT.
Example
SANDSTONE: light grey-brown, friable, medium-coarse grain, rounded,
well sorted, trace calcareous cement, trace glauconitic, faint hydrocarbon odour.
SHOW: faint trace light brown oil stain, fair pale yellow direct fluorescence, strong
white streaming cut fluorescence, pale yellow UV residue ring, light brown residue
ring.

3
 2- Limestone/Dolomite:
1. Rock Type.
 Limestone LST
 Dolomite DOL
2. Durhams Classification
 Mudstone mdst
 Wackestone wkst
 Packstone pkst
 Grainstone grst
 Boundstone bdst
 Crystalline carbonate xln CO3
3. Colour of rock – use colour charts.
The dominant colour is first. The least significant colour last.
4. Crystal Size
 1.000-2.000mm very coarse crystalline v crs xln
 0.500-1.000mm coarse crystalline crs xln
 0.250-0.500mm medium crystalline m xln
 0.250-0.125mm Fine crystalline f xlm
 0.125-0.063mm Very fine crystalline v f xln
 0.063-0.004mm Microcrystalline micrxln
 <0.004mm Cryptocrystalline
5. Hardness
 Brittle brit
 Crumbly cmb
 Soft sft
 Friable fri
 Firm frm
 Hard hd
 Very hard v hd
6. Shape of cuttings
 Amorphous amor
 Sub blocky sb blky
 Blocky blky
 Platy (flat and thin) plty
 Splinterysplty
7. Crystal Shape (rarely used)
 Euhedral (well defined crystal sha pe) euh
 Sub Euhedral (Slight shape) sb euh
 Anhedral (no shape) anhed
 Fiberous (like pieces of material) fib

4
8. Sedimentary structures
 Fiberous fib
 Sucrosic suc
 Vitreous vit
 Gritty grit
 Rough rgh
 Smooth sm
 Bituminous bit
 Chalky chk
 Oolitic ool
 Styolitic styl
 Waxy wxy
 Earthy rthy
 Greasy gsy
9. Major Characteristics
 Carbonaceous (pieces of coal) carb
 Dolomitic dol
 Sandysdy
 Silty slty
 Argilaceous arg
 Glauconitic glauc
 Pyritic (fools gold) pyr
 Micaceous micac
10. Accessories
 Chert cht
 Glauconite glauc
 Lignite (pieces of fossilized wood). lig
 Muscovite musc
 Pyrite pyr
 Sulphurs
 Haematite heam
11. Porosity
 No visible porosity n v p
 Poor visible porosity (fracture) p v p
 Fair porosity (Pin point) fr v p
 Good porosity (Intergranular) gd v p
 Excellent porosity (Vuggy(Interconnecting)) ex v p

5
 3- Anhydrite
1. Rock Type
 Anhydrite ANHY
2. Colour/transparency – use colour charts
 transparent transp
 translucent transl
 opaque opq
3. Crystal Size
 1.000-2.000mm very coarse crystalline v crs xln
 0.500-1.000mm coarse crystalline crs xln
 0.250-0.500mm medium crystalline m xln
 0.250-0.125mm Fine crystalline f xlm
 0.125-0.063mm Very fine crystalline v f xln
 0.063-0.004mm Microcrystalline micrxln
 <0.004mm Cryptocrystalline crypxln
4. Hardness
 Brittle brit
 Soft sft
 Firm frm
 Hard hd
 Very hard v hd
Eg. Firm to moderately hard. Can also be more dominant in one hardness
compared with another. Eg. Predominantly hard, occasionally firm.
5. Shape of cuttings
 Amorphous (has no shape) amor
 Sub blocky sb blky
 Blocky blky
 Platy (flat and thin) plty
 Splintery splty
6. Sedimentary structures
 Fiberous fib
 Sucrosic suc
 Vitreous vit
 Gritty grit
 Rough rgh
 Smooth sm
 Bituminous bit
7. Major Characteristics
 Calcareous calc
 Carbonaceous (pieces of coal) carb
 Sandysdy
 Silty slty
 Argilaceous arg
6
 4- Claystone/Siltstone:
1. Rock Type.
 Claystone CLST
 Siltstone SLTST
2. Colour of rock – use colour charts.
The dominant colour is first. The least significant colour last.
3. Hardness
 Brittle brit
 Plastic plas
 Crumbly cmb
 Soft sft
 Firm frm
 Hard hd
 Very hard v hd
Can grade from one hardness to another. Eg. Firm to moderately hard.
Can also be more dominant in one hardness compared with another.
Eg. Predominantly hard, occasionally firm.
4. Shape of cuttings
 Amorphous (has no shape) amor
 Sub blocky sb blky
 Blocky blky
 Platy (flat and thin) plty
 Splintery splty
5. Sedimentary structures
 Waxy (looks like a candle)wxy
 Earthy (looks like dirt) rthy
 Laminated (thin beds through the sample – beware of PDC cuttings) lam
 Rough rgh
 Greasy gsy
 Smooth sm
6. Major Characteristics
 Calcareous calc
 Carbonaceous (pieces of coal) carb
 Dolomitic dol
 Sandysdy
 Silty (for claystone description only) slty
 Argilaceous (for siltstone description only) arg
 Glauconitic glauc
 Pyritic (fools gold) pyr
 Micaceous micac
7
7. Accessories
 Chert cht
 Glauconite glauc
 Lignite lig
 Muscovite musc
 Pyrite pyr
 Sulphurs
 Haematite heam
How the accessory mineral is distributed may also be described.
Eg. Fine disseminated pyrite of loose pyrite nodules. Lse pyr nod
8- Gradational changes.
If the Claystone is becoming increasingly calcareous:
CLAYSTONE – CALCAREOUS CLAYSTONE – ARGILLACEOUS LIMESTONE.

If the Claystone is becoming siltier:

CLAYSTONE – SILTY CLAYSTONE – ARGILLACEOUS SILTSTONE.

CLAYSTONE: dark grey, occasionally dark green/grey, firm to hard, slightly fissile,
trace calcareous, rare glauconitic, slight earthy texture

8
 5- Halite

1. Rock Type
 Halite HAL
2. Colour/transparency – use colour charts
 transparent transp
 translucent transl
 opaque opq
3. Crystal Size
 >2.000mm Massive crystalline mass xln
 1.000-2.000mm very coarse crystalline v crs xln
 0.500-1.000mm coarse crystalline crs xln
 0.250-0.500mm medium crystalline m xln
 0.250-0.125mm Fine crystalline f xlm
 0.125-0.063mm Very fine crystalline v f xln
 0.063-0.004mm Microcrystalline micrxln
 <0.004mm Cryptocrystalline crypxln
4. Hardness
 Brittlebrit
 Soft sft
 Firm frm
 Hard hd
 Very hard v hd
Can grade from one hardness to another. Eg. Firm to moderately hard. Can also
be more dominant in one hardness compared with another. Eg. Predominantly
hard, occasionally firm.
5. Shape of cuttings
 Amorphous amor
 Sub blocky sb blky
 Blocky blky
 Platy (flat and thin) plty
 Splinterysplty
6. Major Characteristics
 Calcareous calc
 Carbonaceous (pieces of coal) carb
 Sandysdy
 Silty slty
 Argilaceous arg

9
 6- Tuff/Igneous Intrusions
1. Rock Type
 Tuff TF
2. Colour/transparency
Use colour charts
3. Hardness
 Brittlebrit
 Softsft
 Firmfrm
 Hardhd
 Veryhardvhd
Can grade from one hardness to another. Eg. Firm to moderately hard. Can also
be more dominant in one hardness compared with another. Eg. Predominantly
hard, occasionally firm.
4. Shape of cuttings
 Amorphous amor
 Sub blocky sb blky
 Blocky blky
 Platy (flat and thin) plty
 Splinterysplty
5. Accessories
 Chert cht
 Glauconite glauc
 Lignite lig
 Pyrite pyr
 Sulphurs

10
 7- Coal/Lignite
1. Rock type
 Coal COAL
 Lignite LIG
2. Colour –
Use colour charts
3. Lustre
 Dull dull
 Vitreous vit
 Waxy wxy
 Earthy rthy
4. Fracture
 Angular ang
 Conchoidal conch
 Sub conchoidal sb conch
5. Hardness
 Brittle brit
 Soft sft
 Firm frm
 Hard hd
 Very hard v hd
Can grade from one hardness to another. Eg. Firm to moderately hard. Can also
be more dominant in one hardness compared with another. Eg. Predominantly
hard, occasionally firm.
6. Compaction
 Poorly compacted p cpt
 Moderately compacted mo cpt
 Well compacted w cpt
7. Major Characteristics
 Bituminous bit
 Argillaceous arg
 Pyritic (fools gold) pyr
8. Fossils
 Occasionally plant remains

11
 Oil Show Evaluation
1-ODOUR
The smell should be described in the range of faint, fair to strong, as this will
normallydistinguish between condensates, light oils and heavy oils.
2-Check the wet sample under microscope
Color [light brown to dark brown]
Distribution [spotty, streaky, patchy or uniform]
3-Check the sample under fluoroscope (Fluorescence)
Intensity and Brightness[color depth]
4-Sample Cut with solvent (leaching out of hydrocarbons from rock)
- Normal Cut (for permeable rocks)
- Crush Cut (for impermeable rocks)
Nature [diffuse, streaming, blooming]
Speed [slow, fast]
Color [pale blue, blue/white to pale white, milky white or pale yellow]
5-Natural cut (solvent color in natural light immediately after cut)
Color [Slight discoloration to dark brown]
6-Residue (after solvent evaporation)
Natural Residue (In natural light)
UV Residue (Under fluoroscope)
Color [Light to dark brown]
EXAMPLE1 :

EXAMPLE2 :
SS: CLR-WH, F-MGN, MOD SRT, SBANG,HD, W/CAIC CMT, HI GLAUC, FRI,
GD POR, W/ 50% STK, LT BRN O STN, STK,BRI YEL FLU, STRG YEL STRM
CUT, BRI YEL RING.
Sandstone: Clear to white, fine to medium grained, moderately sorted, sub
angular, hard, with calcareous cement, highly gluconitic, friable, good porosity,

12
with 50% streaky, light brown oil staining, streaky, bright yellow fluorescence,
strong yellowstreaming cut, bright yellow ring.
NOTES
-If there is little or no cut then a crush cut can be performed. This is when a
sample iscrushed slightly before adding the solvent. A crush cut will indicate a rock
with lowpermeability.
- A crush cut is described as a normal cut but it must be noted that a crush cut
wasperformed.
- If performing a cut on chalk, the sample must be DRY before attempting the cut,
aswet chalk will always produce a weak cut due to poor permeability and surface
tension
-Chemicals Used for Solvent Cut Test
• Trichloroethane, Propanol, Acetone and Chloroform

SUMMARY

13
 Chemical Tests
1-HCl Effervescence
A quick test can be made with 10% hydrochloric acid to distinguish between calcite
and dolomite.
Separate the cuttings from the sample tray and place in a porcelain spot tray. Add
a few drops ofacid to the sample and view the results: -
Calcite: Immediate and violent effervescence, completely dissolving the sample.
Dolomite: Delayed and slow effervescence, increasing on heating the sample.
Mixture: Intermediate reaction.

2-HCl Oil Reaction

If oil is present, large bubbles will form on a cutting when it is immersed in dilute
HCl.
3-Swelling
Significant swelling or flaking in water is characteristic of montmorillonite or
smectite clays anddistinguishes them from kaolinite and illite clays.
On adding distilled water to clay, the swelling can be described as follows:
Non swelling -No break up
Hygroturgid-Random swelling
Hygroclastic -Swelling into irregular pieces
Hygrofissile - Swelling into flakes (Flaking)
Cryptofissile - Swelling into flakes after adding dilute HCl
Swelling clays will also tend to be soft and sticky (although oil-based and inhibitive
mud systemswill prevent swelling) making sample washing and sample description
very difficult.

4-Sulphate test – Gypsum and Anhydrite

To determine the presence of gypsum or anhydrite use the following procedure:
- Crush 2g of washed, dried sample and place in a test tube.
- Add 5ml of dilute 10% HCl acid.
- Heat
- Filter off residue and place in a clean test tube.
- Add approximately 10 drops of Barium Chloride (BaCl2)
If a white precipitate forms, then the sample is indeed a Sulphate – either
gypsum or anhydrite.
To distinguish between the two, it should be noted that gypsum is not so common
in thesubsurface, therefore, the sample will typically be anhydrite. Also anhydrite is
commonlyassociated with dolomite.
However, to confirm the distinction use the following procedure:
- Heat the same residue until evaporations begins
- Leave for 15mins
If the sample is gypsum, fine fibrous crystals will form.

14
5-Chloride Test
To confirm the presence of salt or Halite (NaCl) the following test can be used:
- Crush 2g of washed, dried sample and place in a test tube.
- Heat in distilled water and filter off the residue
- Place the residue in a clean test tube
- Add 10 drops of Silver Nitrate (AgNO3)
If a white precipitate forms then chlorides are present.

6-Alizarin Red
This is another test to distinguish between calcite and dolomite.
This can simply be dropped on to the cuttings – if calcite is present it will turn a
deep red Colourwhile everything else remains uncolored.

7-Cement Test
After drilling through casing shoes at the start of a new hole section, it is useful to
confirm thepresence of cement.
As it is alkaline, this can be done by adding phenolphthalein (pH indicator) after
washing thesample. If the “cuttings” turn bright purple then they are cement.

15
 SAND STONE CLASSIFICATION
1- MINERALOGICAL COMPOSTION
Sand stone mineralogically consist of the following:-
1- Quartz (SiO2) silica 2- Feldspars 3- Rock fragment 4- Clay minerals
5- Heavy minerals
There are three factors play very important rule in the distribution, spreading and
presence of these minerals in any sand stone sample
1-Availability: it means how much the mineral present in the pre-exiting rock
(quantity)
2- Stability: it refers to the chemical stability of the mineral (its resistance to
attack by chemical solutions)
3- Durability: it refers to the physical or mechanical stability of the rock.
2- SAND STONE MATURITY
It means how much the sand stone sample is matured:
1- Mineralogical maturity: - it depend on the amount of the minerals which had
high stability and durability in the sample where as this ratio increase the maturity
increase
2- Textural maturity:
Most of rocks consist of a-framework b-matrix c-cement - so textural maturity
depends on:
1- The ratio between the framework and matrix
(If matrix ratio less than 15% the rock be texturally mature- If matrix ratio more
than 15% the rock be texturally immature)
2- Sorting (If rock is well sorted it called texturally mature rock – If rock is poorly
sorted it called texturally immature rock)
3- Roundency (If rock grains are well rounded it called texturally mature rock – If
rock grains are angular it called texturally immature rock)
3-SAND STONE CLASSIFICATION
Depending on the ratio between framework and matrix in the sample sand stone
can be classified into:
1- Arenite group: in which the matrix ratio be less than 15 %.( high energy
media of deposition and coarse grains sample)
2-Wacky group:in which the matrix ratio be more than 15 %.( low energy media
of deposition and fine grains sample with high clay content)

4- SAND STONE DIAGENESIS

1-Compaction process lead to decrease in porosity and permeability
2-Cementation by the chemically precipitated matter (calcareous, siliceous,
Ferreganous, kaolinitic). Depend on the ph of the medium.
16
 LIMESTONE CLASSIFICATION
Dunham’s Classification
It is textural classification, depending on the ratio between framework (allochems)
and matrix (Micrite) in the sample.

1. Mudstone
Composed of lime mud (smaller than 20 microns) and less than 10% grains
Mud supported.
2. Wackestone
Composed primarily of lime mud, with more than 10% grains(larger than 20
microns) Mud supported.
3. Packstone
Composed primarily of grains, and grain supported. Greater than10% interstitial
mud matrix and occasionally sparry calcite orpore space.
4. Grainstone
Composed of grains, and grain supported. Less than 10%interstitial mud matrix.
5. Boundstone
Original constituents were bound together and supported inplace, by organic
growth.
6. Crystalline
All original textures are lacking due to the effects ofrecrystallization. Distinct crystal
faces, with occasional relicts.
LIME STONE DIGENESIS
1-Dolomitization process by replacement of Ca with Mg ions which lead to increase
the secondary porosity
2-Dissolution by the action of acidic solution or change in PH of the medium
Flow chart to determine the limestone type

17
 BASIC TERMS
1-Sphericity:Refers to a comparison of the surface area of a sphere of the same
volume asthe grain,with the surface area of the grain itself.
2-Roundness: Roundness, which refers to the sharpness of the edges and
corners of a fragment, is animportant characteristic that deserves careful attention
in detailed logging.
3-Sorting:Sorting is a measure of dispertion of the size frequency distribution of
grains in asediment or rock. It involves shape, roundness, specific gravity and
mineralcomposition as well as size.
4-Cement: Is a chemical precipitate deposited around the grains and in the
interstices ofsediment as aggregates of crystals or as growths on grains of the
same composition.
5-Matrix:Consists of small individual grains that fill intersections between the
largergrains.(Cement is deposited chemically and matrix mechanically).
6-Luster
- Describes the surface features of a cutting under reflected light
- Observe features with naked eye and under microscope and when wet and dry
- Rotating the sample tray under the light source also helps in describing luster
7-Hardness and Indurations
1-Hardness is a physical parameter based on the amount of force required to break
apart the cutting using a simple probe
2-Indurations is the process by which a sediment is converted into a sedimentary
rock. It is function of the type and quantity of the cement
Sample Hardness

Hardness Definition
Loose Grains fall apart in dry conditions
Friable Grains can be detached by fingernails, or a rock
sample crumbles between the fingers
Moderately Grains can be detached using a knife or needle.
hard Small chips are easily broken by hand
Hard Grains cannot be detached using knife of needle.
Rock sample fractures between grains
Very hard Rock fractures through grains
Soft as in swelling clays
Plastic plastic clay, deforms easily
Brittle as in coal

18
Hardness is a reflection of degree of cementation.
1-Soft or friable 2-Moderately hard; fairly cemented.
3-Hard; moderately cemented. 4-Very hard; well cemented.
8-Micrite & Sparite
1-Micrite: abbreviation of “microcrystalline ooze”; a precipitate formed within the
basin of deformation and showing no or little evidence of transport; consists of
crystals 1-4 μm diameter occuring as matrix (dull and opaque ultra fine-grained
material that forms the bulk of limestones and the matrix of chalk)
2-Sparite: cement consists of clean calcite crystals, generally longer than micrite,
forming pore filling cement between grains and within cavities
9-Porosity Classification of Carbonate Rocks
- Intergranular – pore space between grains or particles of a rock
- Intercrystal – pore space between crystals of a rock
- Vuggy – pore space between grains or crystals of a rock wherein the space is
equal or larger than the size of the individual grains or crystals. It usually has the
form of irregular voids.
- Moldic – due to the leaching of soluble grains
- Fracture
10-Crystal Structure Terminology
- Anhedral - no visible crystal form
- Subhedral - partly developed crystal form
- Euhedral - well developed crystal form
11-MOH’S SCALE OF MINERAL HARDNESS

1-TALC 2- GYPSUM 3- CALCITE 4- FLUORITE

5- APATITE 6-FELDSPAR 7- QUARTZ 8- TOPAZ
9- CORUNDUM 10-DIAMOND
12-CLEAVAGEis the property of a mineral that allows it to break repeatedly along
smooth, flat surfaces.
13-FRACTUREis defined as the way a mineral breaks other than cleavage.
14-STREAK is defined as the colour of the mineral in powder form
Percentage of Accessory Minerals

19
MINERAL PROPERTIES:
FLUORESCENCE and PHOSPHORESCENCE
Fluorescence is a phenomenon that causes a mineral to "glow" in the within the visible spectrum
when exposed to ultraviolet light. Minerals that exhibit fluorescence are known as "fluorescent
minerals". Fluorescent minerals contain particles in their structure known as activators, which
respond to ultraviolet light by giving off a visible glow. One of the most common activators is
Manganese. Ultraviolet light is a form of electromagnetic radiation invisible to the human eye.
This light is given off by the sun and by common fluorescent lamps, which also give off
considerable white light (visible light), preventing the fluorescence from being seen. The
ultraviolet reaction is only visible with a special fluorescent lamp with a filter that blocks white
light but allows ultraviolet light to pass through. This lamp is known as an ultraviolet fluorescent
lamp, or UV lamp. Obviously, the reaction will only be visible in a dark area, where the presence
of white light is minimal.
There are two classified ultraviolet wavelengths: longwave (3600 Å) and shortwave (2700 Å).
Some minerals fluoresce the same color in both wavelengths, others fluoresce in only one
wavelength, and yet others fluoresce different colors in different wavelengths. Some UV lamps
have two separate filters: one for longwave and the other for shortwave. Many more minerals
fluoresce in shortwave than in longwave; only a small amount fluoresce in longwave. Longwave
fluorescent lamps are fairly inexpensive, whereas shortwave lamps are more costly. When this
guide labels a mineral as fluorescent without specifying longwave or shortwave, shortwave
fluorescence is implied.
Fluorescence is not always reliable method for mineral identification, since certain minerals of the
same species may fluoresce different colors from different localities, but it can still be an
indicator. Once a mineral has been identified, its fluorescent color is sometimes used to identify
its place of origin. Similarly, if an unidentified mineral from a certain locality glows a specific
color, it can often be identified by the color of its fluorescence.
Color and intensity of the fluorescence varies among specimens of a particular mineral. However,
specimens from the same locality virtually always fluoresce the same color. Calcite may fluoresce
red, orange, yellow, white, and green, but it will always fluoresce red at Franklin, New Jersey,
and bluish-white at Terlingua, Texas.
When a fluorescent lamp is lit, never look directly at the light source, as it can permanently
damage the eyes. In addition, skin should not be exposed to the light source for extended
periods, as it can cause sunburns and long term skin problems.
Below is a fluorescent Willemite and Calcite specimen from the Sterling Hill Mine in Ogdensburg,
in the Franklin District, New Jersey. The Willemite fluoresces green, and the Calcite red.

Specimen under UV Illumination: Specimen under standard Illumination:

(Collection and photos: Hershel Friedman)

20
Phosphorescence is a phenomenon exhibited in several fluorescent minerals where the mineral
continues to glow even after the UV light source has been removed. The glow slowly fades, and
after several seconds (or minutes in a few cases) is no longer visible to the eye. Only few
minerals phosphoresce; phosphorescence is only noted as interesting mineral property, rarely as
a diagnostic identification property. Certain mineral specimens from specific localities all
phosphoresce. Calcite specimens from Terlingua, Texas fluoresce bluish-white with a strong
phosphorescence.

21
Mineral UV Fluorescence Colors Summary Chart
This simplified fluorescence color chart summarizes the colors produced, when minerals are
irradiated with Ultraviolet light. Short Wave UV light causes fluorescence in more rocks than Long
Wave UV light.
.Mineral Ultraviolet Fluorescence Table
Short Wave
Ultraviolet White
SW UV Fluorescence LW UV Light
Color Color Mineral Elements Color Color

13 Light Red . . . .

15 Dark Red Halite Sodium chloride . Various

FFCC00 Light Orange Sodalite NA, Al Silicate Chloride . .

24 Dark Orange . . . .

27 Brown Wulfenite Lead molybdate . Various

32 Light Yellow . . . .

35 Bright Yellow Esperite Ca, Pb, Zn silicate . White

36 Dark Yellow . . . .

43 Light Green Opal Hydrated silicon dioxide . White

44 Bright Green Uranium phosphate . Yellow-

Autunite green
45 Green Willemite Zinc silicate . White

46 Dark Green . . . .

62 Pale Blue Selenite Hydrated calcium sulfate . Clear

65 Light Blue Benitoite Barium titanium silicate . Blue, none

75 Dark Blue Fluorite Calcium fluoride . .

6600FF Bluish Violet Hardystonite Calcium zinc silicate none White

82 Light Violet . . . .
85 Dark Violet . . . .

92 Light Pink Calcite Calcium carbonate . .

95 Dark Pink . . . .

19 White . . . .
70 Blue White . . . .
22
There is a vast range of UV fluorescence colors. This summary "lumps together" more
subtle colors into general color categories, shown on the left.

Some minerals fluoresce at multiple colors, depending upon impurities ("activators") present,
and UV wavelength used. Some minerals will only flouresce using Short Wave UV light,
and some only using Long Wave UV light.

Minerals with Multiple UV Fluorescent Colors

Wave
Mineral Length # Red Orange Yellow Green Blue Violet White

Apatite LW 3 . X X . L . .
(calcium phosphate) SW 2 . X X . . . .

Aragonite LW 2 . . . X . . X
(calcium carbonate) SW 3 . . S X . . X

Barite LW 5 X L X . . X X
(barium sulfate) SW 4 X . X . . X X

Calcite LW 7 X X X X X X X
(calcium carbonate) SW 6 X . X X X X X

Celestite LW 3 . . X . X . X
(strontium sulfate) SW 3 . . X . X . X

Cerussite LW 3 . X X . . . L
(lead carbonate) SW 2 . X X . . . .

Fluorite LW 3 . . X . X . X
(calcium fluoride) SW 3 . . X . X . X

Gypsum LW 3 . . X . X . X
(calcium sulfate) SW 3 . . X . X . X
. .
Scapolite LW 3 . L X . L . .
(Ca, Na, Al silicate
carbonate chloride sulfate) SW 3 S S X . . . S

Scheelite LW 2 . L X . . . .
(calcium tungstate) SW 3 . . X . S . X

Sphalerite LW 4 L X L . L . .
(zinc iron sulphide) SW 1 . X . . . . .
Witherite LW 3 . . X . X . X
23
 (barium carbonate) SW 3 . . X . X . X

Wollastonite LW 4 . X X . X . X
(calcium silicate) SW 4 . X X . X . X

Zircon LW 2 . X X . . . .
(zirconium silicate) SW 2 . X X . . . .

X = Fluorescent under BOTH LW and SW Ultraviolet

L = Fluorescent under Long Wave UV light sources
S = Fluorescent under Short Wave UV light sources

Top 2 Minerals for Fluorescence

Most colors: Calcite can fluoresce in just about all colors, depending upon impurities.
2nd most colors: Barite can fluoresce in various colors.

To be added
Adamite (green),
Clinohedrite (orange),
Diopside (yellow, blue),
Tugtupite (red)

24
 Color
Color of rocks may be a mass effect of the colors of the component grains, orresult from the color of
the cement or matrix, or staining of these. Colors mayoccur in combinations and patterns, e.g., mottled,
banded, spotted, variegated. It isrecommended that colors be described on wet samples under ten-
powermagnification. If is important to use the same source of light all the time and touse constant
magnification for all routine logging. General terms, such as darkgrey and medium brown, generally
suffice.

Ferruginous, carbonaceous, siliceous, and calcareous matter are the mostimportant staining or
coloring agents. From limonite or hematite come yellow,red, or brown shades. Gray to black color can
result from the presence ofcarbonaceous or phosphatic material, iron sulfide, or manganese.
Glauconite,ferrous iron, serpentine, chlorite, and apatite impart green coloring. Red or orangemottling is
derived from surface weathering or subsurface oxidation by theaction of circulating waters.

The colors of cuttings may be alerted, after the

samples are caught, by oxidation caused by storage in a
damp place, insufficient drying after washing, or by
overheating. Bit or pipe fragments in samples can rust
and stain the samples. Drilling mudadditives may also
cause staining.
Place a wet samplenext to color swatches,to
determine whichcolor most closelymatches the
dominantcolor of the sample.

25
26
27
28
29
30
31
 Grain or crystal sizes

Size, grades and sorting of sediments are important characteristics. They have abearing on the
porosity and the permeability of the rocks and may be a reflectionof the environment in which sediment
was deposited. Size classifications are tobe based on a Wentworth scale. The surface data logger
should not try to recordsize grades without reference to a standard comparator of mounted sieved
sandgrains. Other comparators are photomicrographs of thin sections showing bothgrain size and
sorting. Both simple and useful is a photographic grid ofhalf-millimeter squares, which may be placed
near the microscope.

32