Scribd
Upload
243 views3 pages

Fomapan 100

FOMAPAN CLASSIC 100 is a panchromatically sensitized, black-and-white negative film designed for taking photographs. The film meets high requirements for low granularity, high resolving power and contour sharpness and a wide range of halftones. FOMAPAN 100 Classic is compatible with all major processing systems.

Uploaded by

hxbxrt
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
243 views3 pages

Fomapan 100

FOMAPAN CLASSIC 100 is a panchromatically sensitized, black-and-white negative film designed for taking photographs. The film meets high requirements for low granularity, high resolving power and contour sharpness and a wide range of halftones. FOMAPAN 100 Classic is compatible with all major processing systems.

Uploaded by

hxbxrt
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

FOMAPAN CLASSIC 100

DEVELOPING INSTRUCTIONS
Foma B&W film is compatible with all major processing systems. Recommended developing times are for normal contrast negatives (based on intermittent agitation.) All developing times are standardized for 68F / 20C. Your developing time may vary based on environment and equipment used. DEVELOPER Arista 76 Powder Arista 76 Powder Arista Premium Powder Arista Premium Powder Arista Liquid Film Developer Arista Premium Liquid Developer Marathon Film Developer Ilford ID-11, Kodak D-76 Ilford ID-11, Kodak D-76 Kodak XTOL Kodak TMAX Developer Kodak HC 110 Agfa Rodinal DILUTION Stock 1:1 Stock 1:1 Working Solution 1:9 1:9 Stock 1:1 (Straight) 1:4 1:31 1:25 TIME @ 68F / 20C 6-7 8 - 10 6 7 7 7 6 6-7 8 - 10 5-6 5-6 NR 3 1/2

Recommended Agitation: Agitate continuously for first 30 seconds of development, then provide agitation of 5 to 7 inversion cycles for 5 seconds every 30 seconds for remainder of development time. Where continuous agitation is used for rotary processor, reduce the developing times by 15%. Development times may need adjusting to suit individual processing systems and working practices. If an established system is producing good results, adjust the recommended development times until the desired contrast is obtained. This material will be replaced if found defective in manufacture, labeling or packaging. Except for such replacement, this product is sold without warranty or other liability. Developer and film manufacturers can and do change their product specifications from time to time and the development times may change as a result.

FOMAPAN 100 Classic


BLACK-AND-WHITE NEGATIVE FILM
In general FOMAPAN 100 Classic is a panchromatically sensitized, black-and-white negative film designed for taking photographs. The film meets high requirements for low granularity, high resolving power and contour sharpness and a wide range of halftones. FOMAPAN 100 Classic has a nominal speed rating of ISO 100/21 o, but due to its wide exposure latitude the film gives good results even when overexposed by 1 EV (exposure value) (as ISO 50/18 o) or underexposed by 2 EV (as ISO 400/27o) without any change in processing, i.e. without lengthening the development time or increasing the temperature of the developer used. To make prints or enlargements, Extrabrom- and Fomaspeed-type enlarging papers are recommended; however, all sorts of black-and-white enlargement papers can be used. Speed ISO 100/21 o, 21 o SN Schwarzschild effect Exposure (seconds) Lengthening of exposure Correction of aperture number Processing Safelighting Total darkness or infrared light; for a short time an indirect safelighting can be use d (using e.g. an Agfa 108 filter with 15 Watt lamp at a distance of not less than 75 cm. Development FOMAPAN 100 Classic can be processed in all common negative developers. Recommended development times are shown in the table below (the development times are related to development in a spiral developing tank - agitation or turning over continuously during the first 30 seconds, then during the first 10 seconds in every minute). In this way, medium-contrast negatives can be obtained. Developer Development time (minutes) 20 oC 30 oC Fomadon LQN (1+10) 78 2,5 Fomadon R09 (1+40) 67 Fomadon P 78 4 Fomadon Excel 5 6 1,5 Kodak Xtol 56 1,5 Ilford Microphen 57 2 Ilford Perceptol 8 3 Ilford ID 11 stock / Kodak D76 67 3 Tetenal Emofin Liquid 45 When the development time has elapsed, the film is recommended to be shortly rinsed in distilled water or dipped in a 2 % acetid acid solution for 10 seconds. Fixing At a temperature ranging from 18 to 25 oC for 10 minutes in any common type of an acid fixing bath, or for at least 3 minutes in Fomafix rapid fixer. Washing The film should be washed in running water: for 30 minutes and 15 minutes the temperature of water being below 15 oC and over 15 oC respectively. It is recommended to finish the processing with the film being rinsed in distilled water, or dipped in a wetting agent solution. Storage Unexposed films should be stored in the original packaging in a cool, dry place (temperature ranging from 5 to 20 oC, relative humidity from 50 to 60 %), out of reach of harmful vapours, gases and ionizing radiations. Films stored in a refrigerator and a freezer should be acclimatized to room temperature for approx. 2 and approx. 6 hours respectively. Exposed films should be processed as soon as possible. Packaging FOMAPAN 100 Classic is available in the following sorts: - 120 rollfilm 60 mm wide, exlusively on a 120 spool - double-edge perforated 35 mm film in 135-36, 135-24 and 135-12 cartridges for 36, 24 and 12 exposures 24 x 36 mm; bulk length s of 17, 30,5 and 50 m in a darkroom packaging - sheet film (for large-format cameras) sized: 9 x 12, 10 x 15, 12 x 16,5 13 x 18 and 18 x 24 cm in a box of 50 sheets. Other sizes are subject of an agreement with the manufacturer. 1/10001/2 1x 0 1 2x -1 10 8x -3 100 16x -4 Relative spectral sensitivity (wedge spectrogram at 2850 K)
S

Wavelength [nm]

Characteristic curves Exposure: Daylight (5500 K), 1/20 s Developer: Microphen at 20 oC


Optical density
3 2

1
1 5 min 2 7 min 3 11 min

-3

-2

-1 Log rel. exposure

Modulation transfer function


MTF 1,0

0,5

0,1

10

20

50

Spatial frequency [lines per mm]

Resolving power 110 lines per mm Granularity RMS = 13,5 (Microphen at 20 oC, developed to G = 0,6. Measured at D = 1,0. Base The following bases are used for manufacturing the particular sorts of the film: - 120 rollfilm - a bluish polyester base 0,1 mm thick, furnished with a matted colour backing which will decolourize during processing. The backing has anti-halation and anti-curling properties and prevents the incidence of Newton rings during enlarging. - 35 mm film - a gray or gray-blue cellulose triacetate base 0,135 mm thick, - sheet film - a clear polyester base 0,175 mm thick furnished with a matted colour backing which will decolourize during processing. The backing has anti-halation and anti-curling properties and prevents the incidence of Newton rings during enlarging.

The product has been produced and marketed in conformity with a quality system according to the international standard ISO 9001.

DEVELOPMENT CURVES FOR FOMAPAN 100 Classic


Ilford Microphen developer
Dmin/S/G development time curves at 20 and 30 oC - daylight Tc = 5500 K - spiral developing tank - agitation or turning over continuously during the first 30 seconds, then during the first 10 seconds in every minute.
S (o ISO) 125 100 80 64 56 40 16 15
D min 0,30 0,20 0,10

20 oC

G S

S (o ISO) 125 100

30 oC

S 80 1,2 1,0 0,8 G 0,6 0,4 64 56 40 16 15


Dmin 0,40

1,0 G 0,8 0,6 0,4

Dmin

Dmin 0,30
0,20 0,10

4 S (o ISO) 125 100 80 64 56 40 16 15


Dmin 0,30 0,20 0,10

10

12

t (min)

t (min)

Ilford ID 11stock Kodak D 76 developer


Dmin/S/G development time curves at 20 and 30 oC - daylight Tc = 5500 K - spiral developing tank - agitation or turning over continuously during the first 30 seconds, then during the first 10 seconds in every minute.

20 oC

S (o ISO) 125 100 80

30 oC

S 1,2 1,0 G 0,8 0,6 0,4

64 56 40 16 15

1,0 G 0,8 0,6 0,4

Dmin

Dmin

Dmin 0,30
0,20 0,10

0,40

10

12

t (min)

t (min)

Fomadon Excel Kodak Xtol developer


Dmin/S/G development time curves at 20 and 30 oC - daylight Tc = 5500 K - spiral developing tank - agitation or turning over continuously during the first 30 seconds, then during the first 10 seconds in every minute.

S (o ISO) 125 100

20 oC

S (ISO) 160 125

30 oC

S 80 64 G 56 40 16 15
Dmin 0,20 0,10 0,00

100 0,9 0,8 0,7 0,6 0,5


Dmin 0,30

80 G 64 40 16

1,0 0,8 0,6 0,4

Dm in

Dmin 0,20
0,10 0,00

11

t (min)

t (min)

Fomadon LQN developer (1+10)


Dmin/S/G development time curves at 20 and 30 oC - daylight Tc = 5500 K - spiral developing tank - agitation or turning over continuously during the first 30 seconds, then during the first 10 seconds every minute.

S (o ISO) 125 100 80 64 56 40

20 oC

S (o ISO) 125 100

30 oC

S 1,2 1,0 G 0,8 0,6 0,4


Dmin

S 80 64 56 40 16 15
Dmin 0,40 0,20 0,10

1,0 G 0,8 0,6 0,4

16 15
D min 0,30 0,20 0,10

Dmin 0,30

10

12

t (min)

t (min)

FOMA
Bohemia Ltd.

FOMA 7/02

501 04 Hradec Krlov Czech Republic

Tel.: +420 495 733 258 Fax: +420 495 733 376

[email protected] www.foma.cz

You might also like