Scribd
Upload
63 views

DMM-II

The R-20 syllabus for Mechanical Engineering at JNTUK outlines the course 'Design of Machine Members-II' for the III Year - II Semester, focusing on the design of bearings, engine parts, curved beams, power screws, and power transmission systems. It includes detailed units on various mechanical components, their design principles, and applications, along with recommended textbooks and references. The course aims to equip students with practical design skills and knowledge applicable in mechanical engineering.

Uploaded by

nallavinodkumar06
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
63 views

DMM-II

The R-20 syllabus for Mechanical Engineering at JNTUK outlines the course 'Design of Machine Members-II' for the III Year - II Semester, focusing on the design of bearings, engine parts, curved beams, power screws, and power transmission systems. It includes detailed units on various mechanical components, their design principles, and applications, along with recommended textbooks and references. The course aims to equip students with practical design skills and knowledge applicable in mechanical engineering.

Uploaded by

nallavinodkumar06
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

R-20 Syllabus for ME JNTUK w. e.f.

2020–21

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY KAKINADA


KAKINADA–533003, Andhra Pradesh, India
DEPARTMENT OF MECHANICAL ENGINEERING

MENTOFMECHANICALENGINEERING
L T P C
III Year - II Semester OFMECHANICALENGINEERING
3 0 0 3
DESIGN OF MACHINE MEMBERS-II

Course objectives:
1) To gain knowledge about the design of bearings.
2) To understand the concepts in designing various engine parts.
3) To gain knowledge to design curved beams and power screws.
4) To understand power transmission systems and to design pulleys and gear drives.
5) To understand the concepts in designing various machine tool elements.

UNIT– I:
BEARINGS: Classification of bearings- applications, types of journal bearings – lubrication –
bearing modulus – full and partial bearings – clearance ratio – heat dissipation of bearings, bearing
materials – journal bearing design – ball and roller bearings – static loading of ball & roller
bearings, bearing life.

UNIT– II:
ENGINE PARTS: Connecting Rod: Thrust in connecting rod – stress due to whipping action on
connecting rod ends – cranks and crank shafts, strength and proportions of over hung and center
cranks – crank pins, crank shafts.
Pistons, forces acting on piston – construction design and proportions of piston, cylinder, cylinder
liners,

UNIT– III:
DESIGN OF CURVED BEAMS: introduction, stresses in curved beams, expression for radius of
neutral axis for rectangular, circular, trapezoidal and t-section, design of crane hooks, c –clamps.
DESIGN OF POWER SCREWS: Design of screw, square ACME, buttress screws, design of nut,
compound screw, differential screw, ball screw- possible failures.

UNIT– IV:
POWER TRANSMISSIONS SYSTEMS, PULLEYS: Transmission of power by belt and rope
drives, transmission efficiencies, belts – flat and V types – ropes - pulleys for belt and rope drives,
materials, chain drives
SPUR & HELICAL GEAR DRIVES: Spur gears- helical gears – load concentration factor –
dynamic load factor, surface compressive strength – bending strength – design analysis of spur
gears – estimation of centre distance, module and face width, check for plastic deformation, check
for dynamic and wear considerations.
R-20 Syllabus for ME JNTUK w. e.f.2020–21

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY KAKINADA


KAKINADA–533003, Andhra Pradesh, India
DEPARTMENT OF MECHANICAL ENGINEERING

MENTOFMECHANICALENGINEERING
UNIT– V:
MACHINE TOOL ELEMENTS: Levers and brackets: design of levers – hand levers-foot lever –
OFMECHANICALENGINEERING
cranked lever – lever of a lever loaded safety valve- rocker arm straight – angular- design of a crank
pin – brackets- hangers- wall boxes.
Wire Ropes: Construction, Designation, Stresses in wire ropes, rope sheaves and drums.

Note: Design data book is permitted for examination

TEXT BOOKS:
1. Machine Design/ V. Bhandari/TMH Publishers
2. Machine Design/ NC Pandya & CS Shaw/ Charotar publishers

REFERENCES:
1. Machine Design: An integrated Approach / R.L. Norton / Pearson Education
2. Mech. Engg. Design / JE Shigley/Tata McGraw Hill education
3. Design of machine elements- spots/Pearson Publications
4. Machine Design-Norton/Pearson Publications.
Course Outcomes: At the end of the course, student will be able to
CO1: Apply knowledge about the design of bearings.
CO2: Explain the concepts in designing various engine parts.
CO3: Utilize the knowledge to design curved beams and power screws.
CO4: Justify power transmission systems and to design pulleys and gear drives.
CO5: Apply the concepts in designing various machine tool elements.

You might also like