MP ROAD DEVLOPMENT CORPORATION LIMITED

Widening and reconstruction of ……………………………... Road

Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
Rebate
BILL NO.1 GENERAL PROVISIONS
1.01 (i) Providing rental accomodation of 100 Sqm carpet area for Month 19742.40
base office for the employer and his staff complete as per
Technical Specification Clause 122, along with all furniture etc.
detailed therein.
(ii) Maintenance of Base office & its furniture & equipments Month 15193.90

1.02 Providing and maintaining vehicles for the Employer including

providing driver, POL etc. complete as per Technical
Specification Clause 123.
a) Hard top Vehicle with AC, Power Steering, etc. Veh. Days 1376.20

1.03 Supply of colour record photographs two prints of size 6" * 4" No. 48.20
mounted in album complete with DVD as per Technical
Specifications Clause 124.
1.04 Supply of additional prints (24"*48") of coloured photographs as No. 213.00
per Technical Specifications Clause 124.
1.05 Supply of DVD containg details as per Technical Specification No. 2087.85
Clause 124.
TOTAL AMOUNT BILL NO.1 CARRIED TO SUMMARY

Rev-04 PAGE 1 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
BILL NO.2 SITE CLEARANCE
2.01 Cutting of trees, including cutting of trunks, branches and
removal of stumps, roots, stacking of serviceable material with
all leads and lifts and earth filling in the depression/pit as per
Technical Specification relevant clauses of Section-200.

(a) Girth from 300 mm to 600 mm each 180.00

(b) Girth beyond 600 mm to 900 mm each 336.00
(c) Girth beyond 900 mm to 1800 mm each 632.00
(d) Girth beyond 1800 mm Each 1179.00
2.02 Removal of stumps and roots of trees cut by other agencies and
earth filling in the depression/pit as per Technical Specification
Clause 200.

(a) Girth from 300 mm to 600 mm each 171.50

(b) Girth beyond 600 mm to 900 mm each 329.30
(c) Girth beyond 900 mm to 1800 mm Each 585.50
(d) Girth beyond 1800 mm Each 720.85
2.03 Scarification of existing bituminous surface and disposal of Sqm 4.00
scarified material with all lead and lift complete as per clause of
501.8.3.2.

2.04 Dismantling structures and pavement including disposal of

resulting material as per relevant clause of Technical
Specifications Section 200 including salvage value of
dismantelled material.

(a) Cement Concrete Pavement cum 1027.00

(b) Sub base/base course cum 371.00
(Granular/macadam base including GSB and drainage layers)

(c) Stone masonry in lime / cement mortar cum 230.00

(d) Dry rubble stone masonry cum 175.00
(e) Guard stone/ kilometer stone/sign post/hect.stones each 158.00
(f) Deleted
(g) Plain Cement/Lime concrete structures cum 323.00
(h) Prestressed/ RCC structures including reinforcement cum 825.00
(i) Hume pipe of any class
i) Diameter up to 600 mm Liner 120.00
Meter
ii) Diameter beyond 600 mm to 900 mm Liner 162.00
Meter
iii) Diameter over 900 mm Liner
Meter 278.00
(j) Deleted
(k) Brick Masonary Structures cum 230.00
(l) RCC Railing metre 224.92
(m) Deleted
(n) Dry Rubble Masonary/ Stone pitching/boulder apron/brick Cum
soiling/stone soiling
2.05 Dismantling of barbed wire fencing/ wire mesh fencing including metre 36.00
posts, foundation concrete, back filling of pit including disposal
of dismantled material with all lifts and leads, stacking
serviceable material and unserviceable materials separately
including salvage value of dismantled material.

Rev-04 PAGE 2 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
2.06 Removal of telephone / Electric poles including excavation and each 127.00
dismantling of foundation concrete and lines under the
supervision of concerned department, back filling of foundation
pit, stacking the serviceable and unserviceable materials
separately including solvage value of dismantling material
disposal with all lifts and leads.

TOTAL AMOUNT BILL NO.2 SITE CLEARANCE CARRIED TO

SUMMARY
BILL NO.3 EARTH WORK
3.01 Excavations of existing road, embankment, shoulders, ground
and for Cement Concrete drains to designated widths and
depths for the purpose of drain, pavement construction,
trimming of bottom and side slopes in accordance with
requirements of lines, grades and cross Sections, rolling of
bed/ground including loosening and recompaction, if required
and disposal of suitable/surplus and unsuitable materials
through all leads and lifts as per relevant clauses of Section-
300.

(a) In all types of soil cum 50.00

(b) Rock
(i) Ordinary rock cum 63.00
ii) In hard rock (requiring blasting) including salvage value cum 179.00

iii) In hard rock (blasting prohibited) including salvage value cum 344.00

3.02 Construction of embankment/sub-grade/shoulders with cum 73.00

approved materials obtained from roadway cutting , excavation
from drain, foundation of structures and transportation through
all lifts and leads including spreading, grading to required level
and camber and compacting using viabratory roller to meet
requirement of table No. 300-1 & 300-2 and as per relevant
clauses of Section-300 & 400.

3.03 Construction of embankment / sub grade / earthen shoulders

with approved material obtained from borrow pits with all lifts &
leads including excavation, transporting to site, spreading,
grading to required level & Camber and compacting using
viabratory roller to meet requirement of table No. 300-1, 300-2
and as per relevant clauses of Section 300 & 400.

(a) Earth with CBR more than 5% cum 154.00

(b) Earth with CBR more than 12% for shoulders above drainage cum 223.00
layer
3.04 Construction of unlined surface drain of average cross sectional Metre 46.00
area 0.4 Sqm. In all type of Soil to specified lines, grades,
Levels & dimentions to the requirement of clause 301 & 309
including disposal of unsuitable material with all lead & lift and
using suitable material as per the direction of the Engineer.

3.05 Construction of Median above road level with approved material cum 177.00
obtained from borrow pits including excavation & Transportation
through all lead & lift and Spreading, Grading, Compacting as
per relavent clauses of section - 400.

Rev-04 PAGE 3 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
TOTAL AMOUNT BILL NO.3 EARTHWORK CARRIED TO
SUMMARY
BILL NO. 4 SUB-BASE, BASE-COURSE
4.01 Construction of granular sub-base by providing close/coarse
graded crushed material, spreading in uniform layers on
prepared surface and compacting at OMC with vibratory roller
to achieve the desired density, complete in all respect as per
drawing & relevant clauses of Section-400.

(i) For (GSB 2nd/ Top layer) grading-III Material as per Table 400-1. cum 599.00

(ii) For Drainage layer GSB grading- V Material (GSB 1st Layer) as cum 530.00
per Table 400-1.
4.02 Providing, laying, spreading and compacting graded stone cum 1330.00
aggregate to wet mix macadam specification including
premixing the Material with water at OMC in mechanical mix
plant, carriage of mixed Material by tipper to site, laying in
uniform layers on well prepared surface with sensor paver and
compacting with vibratory roller to achieve the desired density
and as per relevant clauses of Section-400.

TOTAL AMOUNT BILL NO. 4 SUB BASE CARRIED TO

SUMMARY
BILL NO. 5 PAVEMENT
5.01 Providing and applying primer coat with bitumen emulsion on Sqm. 35.00
prepared surface of granular Base with low porosity (WMM or
WBM) including clearing of road surface and spraying primer at
the rate of 0.75 kg/sqm with pressure distributor and as per
relevant clause of Section-500.

5.02 Providing and applying tack coat with bitumen emulsion using
emulsion pressure distributor on the prepared bituminous /
granular surface cleaned with mechanical broom and as per
relevant clauses of Section-500.

( i) @ 0.25 kg per sqm (normal bituminous surfaces) Sqm. 12.00

(ii) @ 0.30 kg per sqm (dry & hungry bituminous surfaces/granular Sqm. 15.00
surfaces treated with primer)
5.03 Providing and laying leveling course/profile corrective course cum 5291.00
with bituminous macadam with hot mix plant using crushed
aggregates of grading-2 premixed with bituminous binder @
3.4% as per clause 504.3.1, transported to site, laid over a
previously prepared surface with sensor paver finisher to the
required grade, level and alignment and rolled as per clauses
501.6 and 501.7 to achieve the desired compaction complete in
all respects and as per relevant clauses of Section-500.

5.04 Providing and laying dense bituminous macadam with hot mix
plant using crushed aggregates of specified grading, premixed
with bituminous binder, transporting the hot mix to work site,
laying with sensor paver finisher to the required grade, level
and alignment, rolling with smooth wheeled, vibratory and
tandem rollers to achieve the desired compaction complete in
all respects and as per relevant clauses of Section-500. (Only
cement will be used as filler).

Rev-04 PAGE 4 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
(i) for Grading II( 50-75mm thickness ) Cum 7398.00
5.05 Providing and laying bituminous concrete with hot mix plant
using crushed aggregates of specified grading, premixed with
bituminous binder, transporting the hot mix to work site, laying
with a sensor paver finisher to the required grade, level and
alignment, rolling with smooth wheeled, vibratory and tandem
rollers to achieve the desired compaction in all respects and as
per relevant clauses of Section-500. (Only cement will be used
as filler).

(i) for Grading II ( 30-45 mm thickness ) with 60/70 bitumen Cum 8493.00

(ii) for Grading I (50-65 mm thickness) with 60/70 bitumen (VG-30) Cum 8499.00
for wearding coat over C.D. Structures

5.06 Construction of dry lean cement concrete Sub- base over a Cum 2383.00
prepared sub-grade with coarse and fine aggregate conforming
to IS: 383, the size of coarse aggregate not exceeding 25 mm,
aggregate cement ratio not to exceed 15:1, aggregate
gradation after blending to be as per table 600-1, cement
content not to be less than 150 kg/ cum, optimum moisture
content to be determined during trial length construction,
concrete strength not to be less than 10 Mpa at 7 days, mixed
in a batching plant, transported to site, laid with paver with
electronic sensor, compacting with 8-10 tonnes vibratory roller,
finishing and curing and as per relevant clauses of Section-600
(including cost of all types of formworks).

5.07 Construction of dowel jointed, plain cement concrete pavement Cum 5847.00
in M-40 grade concrete over a prepared sub base with 43 or
higher grade cement, maximum size of coarse aggregate not
exceeding 25 mm, mixed in a batching and mixing plant as per
approved mix design, transported to site, laid with a fixed form
or slip form paver with electronic sensor, spread, compacted
and finished in a continuous operation including provision of
contraction, expansion, construction and longitudinal joints,
joint filler, separation membrane, sealant primer, joint sealant,
debonding strip, placing of dowel bar and tie rod, admixtures
as approved, curing compound, finishing to lines and grades as
per approved drawings as per IRC-15 2002 and as per relevant
clauses of section-602 of specifications complete but excluding
cost of steel in dowel bar and tie rod etc. Steel in dowel bars
and tie rod as per design of concrete pavement wil be paid as
per item 6.06 (a) & (b).

Rev-04 PAGE 5 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
5.08 Filling Pot- holes and Patch Repairs with open - graded Premix Sqm 129.00
surfacing, 20mm. including removal of all failed material,
trimming of completed excavation to provide firm vertical faces,
cleaning of surface, painting of tack coat on the sides and
base of excavation as per clause 503, back filling the pot holes
with hot bituminous material as per clause 510, compacting,
trimming and finishing the surface to form a smooth continuous
surface, all as per clause 3004.2.(For maintenance of road
only).

5.09 Repair of pot holes/ patch repair with Grading - IV granular Cum 605.00
material meeting requirement in the Table 400-1 & 400-2 of the
specification including its maintenance as directed by the
Engineer. (For maintenance of road only).

TOTAL AMOUNT BILL NO.5 PAVEMENT CARRIED TO

SUMMARY
BILL NO. 6 CROSS DRAINAGE
6.01 Earth work in excavation of foundation of structures as per
drawing and technical specification, for all depths in all types of
soil/rock including setting out, construction of shoring and
bracing, dressing of sides and bottom, back filling with
approved material, disposal of surplus material etc. within all
leads and lifts complete and as per relevant clauses of Section
300 and 2100 of MORT&H Specifications.

i) In all types of soils Cum 57.00

ii) In ordinary rock Cum 100.00
iii) In hard rock (requiring blasting) including salvage value Cum 380.00
iv) In hard rock (blasting prohibited) including salvage value Cum 503.00

6.02 Providing and laying in position plain cement concrete of grade Cum 4261.00
M-15 in levelling course below open foundation, pile caps,
approach slabs, retaining walls, return walls/wing wall, cut off
walls, CC drain and inspection ladders etc. complete as per
drawing and relevant clauses of Section 1100, 1500, 1700,
2100 & 2700 (including cost of all types of formworks).

6.03 Providing and laying plain cement concrete for foundation and
substructure of abutment, piers, retaining wall, return wall,
wing wall, head wall of HP CD's, pillar, guard wall and CC drain
etc.excluding cost of skin reinforcement, but including
treatment of joints between existing & new structures with all
leads and lifts as per drawings and relevant clauses of Sections
1500, 1700, 2100, 2200, and 2900 (including cost of all types of
formworks).

i) PCC Grade M15 Cum 4695.00

ii) PCC Grade M20 Cum 5220.00
iii) PCC Grade M25 Cum 5767.00

Rev-04 PAGE 6 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
6.04 Providing and laying reinforced cement concrete for foundation
and sub-structure of pile cap, abutment, return wall, wing wall,
head wall, pier, pier cap, pedestals, cantilever/counterfort/Box
abutment/Return, cap, dirt wall, splayed wing wall, retaining
wall, median wall, inspection ladders, box cell structures for
under passes, CC drain, CD's and bridges excluding cost of
reinforcement, including treatment of joints between existing
and new structures with all leads and lifts as per drawings and
relevant clauses of Section 1100, 1500, 1700, 2100, 2200.
(including cost of all types of formworks).

i) RCC Grade M20 Cum 5363.00

ii) RCC Grade M25 Cum 6074.00
iii) RCC Grade M30 Cum 5859.00
iv) RCC Grade M35 Cum 6242.00
6.05 Providing and laying reinforced cement concrete for super
structure of all solid slab/ T-Beam slab / approach slab/ R.C.C
Box Girder super structure / wearing coat / railing / kerb etc. for
CD's and bridges excluding cost of reinforcement, including
treatment of joints between existing and new structures with all
leads and lifts as per drawings and relevant clauses of Section
1500, 1700, 2300, 2700 (including cost of all types of
formworks).

i) RCC grade M20 Cum 5959.00

ii) RCC grade M25 Cum 6515.00
iii) RCC grade M30 Cum 6589.00
iv) RCC grade M35 Cum 6619.00
6.06 Supplying, fitting and placing steel reinforcement bar in
foundation substructure, super structure, piles, concrete
pavement, approach slab, wearing coat, kerb, railing, CC drain
etc. complete as per drawing and relevant clauses of Section
1600.

a) HYSD Bar MT 76480.00

b) Mild Steel (Dowel & Tie Bars of CC Pavement of Road) MT 61068.70
6.07 Providing weep holes in Brick masonry/Plain/Reinforced RM 122.00
concrete abutment, wing wall/return wall with 100 mm dia PVC
pipe, extending through the full width of the structure with
slope of 1V :20H towards drawing face complete as per drawing
and Technical specifications and as per clause 2706 of
specifications.

6.08 Providing Back filling behind abutment, wing wall, return wall Cum 739.00
and Hume pipe trench with Granular Material complete as per
drawing and Technical specification and as per relevant clauses
305 of specifications and as per appendix 6 of IRC-78.

Rev-04 PAGE 7 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
6.09 Providing and laying of Filter media with granular Cum 1127.00
materials/stone crushed aggregates satisfying the requirements
laid down in clause 2504.2.2. of MORTH specifications to a
thickness of not less than 600 mm with smaller size towards the
soil and bigger size towards the wall and provided over the
entire surface behind abutment, wing wall and return wall to
the full height compacted to a firm condition complete as per
drawing and technical specification.

6.10 Providing and fixing in position bearings true to line and level
including all accessories complete as per drawings and
technical specification Section 2000.

(a) Elastomeric bearings as per IRC:83 Cu.cm. 0.86

(b) Tar paper bearings as per IS:1398 sqm 48.00
6.11 Providing and Laying Reinforced cement concrete pipe NP4(as
per IS:458) for culverts on first class bedding of granular
material / concrete bedding including fixing collar/flush joint
with cement mortar 1:2, cost of first class bedding but
excluding excavation, protection works, backfilling, concrete
and masonry works in head walls and parapets and as per
relevant clauses of Section-2900.

a) 600 mm (internal) meter 3543.25

b) 900 mm (internal) meter 3807.65
c) 1000 mm (internal) meter 6316.00
d) 1200mm (interna) meter 8818.00
6.12 (a) Providing and laying of asphaltic plug joint to provide for meter 828.00
horizontal movement of 25 mm and vertical movement of 2
mm, depth of joint varying from 75 mm to 100 mm, width
varying from 500 mm to 750 mm (in traffic direction), covered
with a closure plate of 200mm x 6mm of wieldable structural
steel conforming to IS: 2062, asphaltic plug to consist of
polymer modified bitumen binder, carefully selected single size
aggregate of 12.5 mm nominal size and a heat resistant foam
caulking/backer rod, all as per approved drawings and
specifications and as per relevant clauses of Section 2600.

(b) Providing and fixing 2mm thick corrugated copper plate RM 4397.00
expansion joint with 20mm thick compressible fiber board
below the copper plate to protect the edges, filling with 20mm
thick pre-moulded joint filler over copper plate and sealed with
joint sealing compound consisting of coarse sand and 6%
bitumen by weight as per drawings and relevant technical
specification complete.

6.13 Providing and laying of a strip seal expansion joint catering to RM 11581.00
maximum horizontal movement upto 70 mm, complete as per
approved drawings and standard specifications to be installed
by the manufacturer/supplier or their authorised representative
ensuring compliance to the manufacturer's instructions for
installation and as per relevant clauses of Section 2600.

Rev-04 PAGE 8 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
6.14 Construction of RCC railing of M30 Grade with 12 mm nominal RM 1887.00
size aggregate, true to line and grade, tolerance of vertical
RCC post not to exceed 1 in 500, centre to centre spacing
between vertical post not to exceed 2000 mm, leaving
adequate space between vertical post for expansion, complete
as per approved drawings and technical specifications and as
per relevant clauses of Sections 1500, 1600, 1700 and clause
2703 of specifications (as per MORT & H specification drawing
SD/201 or SD/304).

6.15 Providing and fixing and erecting 40mm dia steel pipe (medium RM 1397.00
weight) railing in 3 rows on steel channel ISMC-100mmx50mm
and 0.95 in height and fixed at 1.8m. center to center and duly
painted etc. complete as per standard drawing No.STD-33R.

6.16 Providing Drainage Spouts complete as per drawing and No 911.00

Technical specification and as per clause 2705 of specifications.

6.17 Testing of span of bridge for deflection due to live load with Ton 787.00
platforms for loading arrangements apparatus for meaurement
including unloading etc. complete as per approved drawing.

6.18 Providing and laying boulders apron/toe wall on river bed for Cum 1193.00
protection against scour with stone boulders weighing not less
than 40 kg each complete as per drawing and Technical
specification and as per relevant clauses of Section
2500.Technical specifications and as directed by the Engineer-
in-charge.

6.19 Providing and laying Pitching on slopes laid over prepared filter
media, Dry boulder toe wall complete as per drawing and
Technical specifications and as per relevant clauses of Section
2500.

a) Stone/Boulder weighing not less than 40 kg each Cum 1193.00

6.20 Providing and laying Filter material underneath pitching in Cum 1259.00
slopes complete as per drawing and Technical specification and
as per relevant clauses of Section 2500.

6.21 Providing and laying Flooring comprising of 150mm thk Flat sqm 4438.00
stone laid over 300mm thk cement concrete M15 complete as
per drawing and Technical specifications bedding and as per
relevant clauses of Section 1400, 1700 & 2500.

6.22 Providing Curtain wall complete as per drawing and Technical

specification and as per relevant clauses of Section 1400 , 1700
and 2500.

a) Cement concrete Grade M15 Cum 4438.00

6.23 Construction of flexible apron comprising of loose stone Cum 1223.00
boulders weighing not less than 40 kg beyond curtain wall and
as per relevant clauses of Section 2500.

6.24 Removal of existing cement concrete wearing coat including its sqm 117.00
disposal complete as per Technical specification without causing
any detrimental effect to any part of the bridge structure and
removal of dismantled material with all lifts and leads and as
per relevant clauses of Section 2800.

Rev-04 PAGE 9 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
6.25 Providing and inserting nipples with approved fixing compound
after drilling holes for grouting as per Technical specifications
including subsequent cutting/removal and sealing of the hole as
necessary of nipples after completion of grouting and as per
relevant clauses of Section 2800.

a) Epoxy / Cement grouting No 102.00

6.26 Sealing of cracks/porous concrete by injection process through
nipples/Grouting complete as per Technical specification and as
per relevant clauses of Section 2800.

a) Epoxy kg 1675.00
b) Cement grouting kg 64.00
6.27 Patching of damaged concrete surface with 25mm thick sqm 1921.00
(Average) polymer concrete and curing compounds, initiator
and promoter, available in present formulations, to be applied
as per instructions of manufacturer and as approved by the
Engineer and as per relevant clauses of Section 2800.

6.28 Guniting concrete surface with 25mm thick (Average) cement sqm 1491.00
mortar applied with compressor after cleaning surface and
spraying with epoxy complete as per Technical specification and
as per relevant clauses of Section 2800.

6.29 Removal of defective concrete, 40mm thick (Average) cleaning sqm 353.00
the surface thoroughly, applying the shotcrete mixture
mechanically with compressed air under pressure, comprising
of cement, sand, coarse aggregates, water and quick setting
compound in the proportion as per clause 2807.1., sand and
coarse aggregates conforming to IS: 383 and table 1 of IS: 9012
respectively, water cement ratio ranging from 0.35 to 0.50,
density of gunite not less than 2000 kg/cum, strength not less
than 25 Mpa and workmanship conforming to clause 2807.6
and as per relevant clauses of Section 2800.

6.30 Providing and Applying 10mm thick (Average) epoxy mortar sqm 1019.00
over leached, honey combed and spalled concrete surface and
exposed steel reinforcement complete as per Technical
specification and as per relevant clauses of Section 2800.

6.31 Providing Epoxy bonding of new concrete to old concrete as per sqm 1210.00
Section 2800.
6.32 Providing and laying new drainage spout including making the Nos. 911.00
joint of drainage spout with slab water tight with non shrink,
free flow cement grout and drilling hole in RCC slab and cutting
chaases in slab of required size for fixing drainage spout
complete as per drawings and technical specificaions section
2700 and 2800.

6.33 Providing Stone masonry work in cement mortar 1:3 for

foundation, substructure, superstructure complete as per
drawing and Technical Specifications and as per relevant
clauses of Sections 1400.

(a)Random Rubble Masonry cum 3912.00

Rev-04 PAGE 10 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
6.34 Providing pointing with cement mortar (1:3 ) on stone/brick sqm 54.00
work in substructure and superstructure as per Technical
specifications and as per relevant clauses of Sections 1300 and
1400.
6.35 Providing Plastering with cement mortar (1:3 ) on stone/brick sqm 115.00
work in substructure and superstructure as per Technical
specifications and as per relevant clauses of Sections 1300 and
1400.

6.36 Repair of damaged stone masonry work in head wall, abutment, cum 1740.25
wing wall, return wall, piers, parapet etc. with CM 1:3
(cement:sand) mortar by placing and setting of displaced
masonary blocks including supplying missing blocks, pointing
and finishing with mortar, to bring the repaired area in line,
level cleaning of the area and scaffolding etc. as required
complete in all respects as per technical specification 200,
1400, 2800.

6.37 Construction of drainage chute on embankment slopes of Nos. 651.70

approaches of bridges/hill slopes in cement concrete M-20 with
M-15 foundation concrete as per drawing and technical
specification Section 1700.
6.38 Replacement of expansion joint: removing existing expansion
joints in weared out condition by chipping out the concrete
around the joints exposing the anchors (if any), installing new
expansion joint as per manufactures specification and as per
approval of Engineer-in-charge. The rate shall include chipping
of the concrete, removal of wearing coats of the area, disposal
of the same, putting additional reinforcement (if required as per
Engineer in Charges specification), supplying and providing of
all the materials, concreting back the chipped of portion of the
concrete deck, installation of the expansion joint, complete as
per the direction of the engineer-in-charge without endangering
the safety of the existing structure.

a) Asphaltic plug joint as per clause 2816 of Technical metre 3293.00

specification.
6.39 Painting two coats after filling the surface with synthetic enamel sqm 51.00
paint in all shades on new/old plastered/concrete surfaces and
as per relevant clauses of section-800 & I.R.C.-67 including cost
of paint etc. complete.

6.40 Deleted sqm

6.41 Provision of an Reinforced cement concrete crash barrier at the Meter 4707.80
edges of the road, approaches to bridge structures and
medians, constructed with M-40 grade concrete with HYSD
reinforcement conforming to IRC:21/ IRC 112 and dowel bars 25
mm dia, 450 mm long at expansion joints filled with pre-
moulded asphalt filler board, keyed to the structure on which it
is built and installed as per design and approved drawing by the
Engineer.

6.42 Providing and filling annular space around footing in rock with cum 4261.00
lean cement concrete M-15 nominal mix in foundation with
crushed stone agreegate 40m nominal size and as per relevant
clauses of sec. 1500, 1700 & 2100.

Rev-04 PAGE 11 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
TOTAL AMOUNT BILL NO. 6 CROSS DRAINAGE CARRIED
TO SUMMARY
BILL NO.7 TRAFFIC SIGNS, MARKINGS AND ROAD
APPURTENANCES
7.01 Providing and fixing of retro- reflectorised cautionary,
mandatory and informatory sign as per IRC :67 made of
encapsulated lens type reflective sheeting vide clause 801.3,
fixed over aluminium sheeting, 1.5 mm thick supported on mild
steel angle iron post75 mm x 75 mm x 6 mm (height from
crown level of the road and bottom of the sign board shall not
be less than 1.5 m.) firmly fixed to the ground by means of
properly designed foundation with M15 grade cement concrete
45 cm x 45 cm x 60 cm, 90 cm below ground level as per
approved drawing including painting of vertical post as per
Technical specification section 800.

i ) 90 cm equilateral triangle each 3946.00

Cautionary/Warning Sign
ii) 60 cm equilateral triangle each 2772.00
Cautionary/Warning Sign
iii) 60 cm circular each 3540.00
'Mandatory/Regulatory Signs
iv) 80 cm x 60 cm rectangular each 4732.00
Informatory Signs
v) 60 cm x 45 cm rectangular each 3462.00
Informatory Signs/Cheveron Sign
vi) 60 cm x 60 cm square each 4006.00
Informatory Signs
vii) 90 cm high octagon each 5894.00
Stop Signs
7.02 Direction and Place Identification signs upto 0.9 sqm size board. sqm 8074.00
(Providing and erecting direction and place identification retro-
reflectorised sign as per IRC:67 made of encapsulated lens type
reflective sheeting vide clause 801.3, fixed over aluminium
sheeting, 2 mm thick with area not exceeding 0.9 sqm
supported on a mild steel single angle iron post 75 x 75 x 6 mm
(height from crown level of the road and bottom of the sign
board shall not be less than 1.5 m.) firmly fixed to the ground
by means of properly designed foundation with M15 grade
cement concrete 45 x 45 x 60 cm, 90 cm below ground level as
per approved drawing including painting of vertical post as per
specification.

Rev-04 PAGE 12 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
7.03 Direction and Place Identification signs with size more than 0.9 sqm. 14087.00
sqm size board. (Providing and erecting direction and place
identification retro- reflectorised sign as per IRC :67 made of
encapsulated lens type reflective sheeting vide clause 801.3,
fixed over aluminium composite sheet 3mm thick supported on
two pultruded composite channel sections 50 x 100 x 50 x 5mm
/ aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm
supported on a mild steel channel post 35mm x 75 mm x 35
mm x 6 mm (height from crown level of the road and bottom of
the sign board shall not be less than 1.5 m.) , 2 Nos. firmly fixed
to the ground by means of properly designed foundation with M
15 grade cement concrete45 cm x 45 cm x 60 cm, 90 cm below
ground level as per approved drawing including painting of
vertical post as per specification.

7.04 Supply and fixing tubular gantry mounted Overhead/cantilever

signs. All components of signs & supports, other than the
reflective portion shall be thoroughly descaled, cleaned, primed
and painted with two coats of epoxy paints. The sign back side
shall be with grey colour and post shall be in black & white
alternate bands. The post below ground shall be painted with
three coats of red lead paint. The sign shall be made as per
IRC-67-2001 and Technical Specification Section 800.

i) Erection of overhead gantry/cantilever structure as per drawing tonnes 72888.20

including steel work in trusses, steel tubes cutting, fixing in
position with welding and bolted complete in all respect and
type as per structural design requirements and approved plans
including cost of excavation, concerte and steel for foundations.

ii) The sign board made out of 2 mm thick alluminium sheet, face sqm 7825.50
to be fully covered by high intensity grade white retro reflective
sheeting of encapsulated lens type. The
background/border/simples/legend/arrows shall be made by
transparent overlay film of desired colour as per sign details
except those in black which shall be of non reflective type. The
sign place shall be fixed with 6 mm dia alluminium rebate on
MS angle iron frame. The angle iron frame shall be made with
angle of size 75 mm x 75 mm x 6 mm with additional bracing at
every 600 mm c/c, if any dimension in more than 1200 mm.

7.05 Providing reinforced cement concrete M15 grade kilometre

stone of standard design as per IRC:8-1980, fixing in position
including painting and printing etc as per relevant clauses of
Section-800 of specifications.

i) 5th kilometre stone (precast) each 2964.00

ii) Ordinary Kilometer stone (Precast) each 1789.00
iii) Hectometer stone (Precast) each 530.00

Rev-04 PAGE 13 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
7.06 Road Marking with Hot Applied Thermoplastic Compound with
Reflectorising Glass Beads on Bituminous Surface (Providing
and laying of hot applied thermoplastic compound 2.5 mm thick
including reflectorising glass beads @ 250 gms per sqm area,
thickness of 2.5 mm is exclusive of surface applied glass beads
as per IRC:35 .The finished surface to be level, uniform and free
from streaks and holes and as per relevant clauses of Section-
800.

i Lane/centreline/edge marking/transverse and any other sqm 636.00

marking
ii) Directional arrows, lettering, etc., as per drawings of MORT & H Nos. 777.40
type design and interSection for National Highways.

7.07 Providing and fixing road delineators complete as per technical

specification Section 800.
a) Triangular object marker 300 mm side with four red reflector, Nos. 1688.10
made out of 2 mm thick alluminium sheet, face to be fully
covered by high intensity grade white retro reflective sheeting
of encapsulated lens type. The background/border/symbols
shall be made by screen printing of desired colour as per sign
details. The sign plate shall be fixed with 6 mm dia alluminium
rebates on MS angle iron frame. The angle iron frame shall be
made with the angle iron of size 40 mm x 40 mm x 5 mm. The
sign shall be fixed with nut bolts and welding on 50 mm (NB)
dia medium weight 500 mm high MS pipe. All components of
signs and supports shall be thoroughly descaled, cleaned,
primed and painted with two coats of epoxy paint. The sign
back side shall be with grey colour and post shall be white
colour. The post below ground shall be painted with 3 coats of
red lead paint.

b) Rectangular hazard marker 600 mm x 300 mm made out of 2 Nos. 2341.40

mm thick alluminium sheet, face to be fully covered by
high intensity grade white retro reflective sheeting of
encapsulated lens type. The background/border/symbols shall
be made by screen printing of desired colour as per sign details.
The sign plate shall be fixed with 6 mm dia alluminium rebates
on MS angle iron frame. The angle iron frame shall be made
with angle of size 40 mm x 40 mm x 5 mm. The sign shall be
fixed to 80 mm dia (NB) MS pipe (MW) support with nut bolts
and welding.

c) Providing and fixing of 1 m RCC guide post 200 mm dia of NP-2 each 980.45
type HP confirming to IS:458-1988 for guard stone, formation
indicators, etc. duly filled with earth except 0.15 m from top,
cement concrete of M-15 topping in 0.075 m and 0.075 m in
pipe embedded in cement concrete block of M-15 size 450 mm
x 450 mm x 500 mm complete in all respects including cost of
painting with white and black paint.

Rev-04 PAGE 14 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
7.08 Road Delineators (Supplying and installation of delineators each 274.00
(road way indicators, hazard markers, object markers), 80-100
cm high above ground level, painted black and white in 15 cm
wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia
circular reflectorised panels at the top, buried or pressed into
the ground and confirming to IRC-79 and the drawings as per
relevant clauses of section-800 of specifications.

7.09 Providing and fixing in position Reinforced cement concrete M- each 483.00
15 grade boundary pillars of standard design as per IRC:25-
1967, including finishing ,painting and lettering etc. complete.

7.10 Road Markers/Road Stud with Lense Reflector (Providing and each 670.00
fixing of road stud 100x 100 mm, die cast in aluminium,
resistant to corrosive effect of salt and grit, fitted with lense
reflectors, installed in concrete or asphaltic surface by drilling
hole 30 mm upto a depth of 60 mm and bedded in a suitable
bituminous grout or epoxy mortar, all as per BS 873 part
4:1973).

7.11 Construction of cement concrete kerb with top and bottom meter 236.00
width 115 and 165 mm respectively, 250 mm high in M 20
grade PCC on M-10 grade foundation 150 mm thick, foundation
having 50 mm projection beyond kerb stone, kerb stone laid
with kerb laying machine, foundation concrete laid manually, all
complete and as per clause 408 of specifications.

7.12 Metal Beam Crash Barrier

(a) Type - A, "W" : Metal Beam Crash Barrier (Providing and erecting meter 4323.00
a "W" metal beam crash barrier comprising of 3 mm thick
corrugated sheet metal beam rail, 70 cm above road/ground
level, fixed on ISMC series channel vertical post, 150 x 75 x 5
mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below
ground/road level, all steel parts and fitments to be galvanised
by hot dip process, all fittings to conform to IS:1367 and
IS:1364, metal beam rail to be fixed on the vertical post with a
spacer of channel Section 150 x 75 x 5 mm, 330 mm long
complete as per clause 810 of specifications.

(b) End Terminal/Anchors Nos. 7304.85

7.13 Providing painting of structure number, span arrangement and Nos. 256.05
flow directions etc.complete as per drawings and technical
specifications Section 800.

Rev-04 PAGE 15 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
7.14 Providing and fixing sign boards made out of 2mm aluminum Nos. 2937.35
sheet/ composite panel size 60x45 cms rectangle plus 30x25
cms additional plate as per the drawing attached (IRC).
Pretreated with phospheting process and acid etching; coated
with one coat of epoxy premier and two coats of best quality
epoxy paint; reflectorised with retro reflective sheeting as per
latest M.O.S.T. Specifications; 3.1 m long Stand post and frame
fabricated from suitable size iron angle of 35x35x3 mm & NB65
MS Pipe as required, painted with best quality epoxy coating in
black and white bends. The details of numerals for each board
shall be as per the instruction of the engineer incharge. The
fixing at site shall be in 1:2:4 CC block of size 45x45x60 cms for
each leg. including excavation curing etc. complete under the
supervision of engineer in charge.

7.15 Providing and laying 80mm thick factory made cement Sqm 691.00
concrete interlocking paver block of M -40 grade made by
block making machine with strong vibratory compaction and of
approved size and design/ shape laid in required colour and
pattern over and including 50mm thick laid compacted bed
of course sand, filling the joints with coarse sand, cement
mortar/concrete etc. with all lead and lifts complete as per the
direction of Engineer.

TOTAL AMOUNT BILL NO. 7 TRAFFIC SIGNS, MARKINGS

AND ROAD APPURTENANCESCARRIED TO SUMMARY
BILL NO. 8 MISCLLANEOUS
8.01 Providing and laying utility duct of 300 mm dia NP-4 pipe in metre 1355.00
urban/rural areas as per technical specification Section 2900
and as directed by the engineer.

8.02 Providing, fixing, laying and jointing 150 mm dia. medium class
PVC Pipe as per relevant IS code including excavation of
trenches in grade and level including cost of couplers and
testing of pipes at factory as per the stipulation in relevant IS
codes etc. complete.

a) 150mm inner diameter metre 281.40

8.03 Re-location of hand pumps including boring , providing hand Nos. 25208.10
pump of approved make and quality, if required complete with
drainage accessibility to the satisfaction of the concerned
department and salvage of dismanteled materials.

8.04 Shifting and relocating utility services such as water supply line,
sewer line, OFC or telecom or electric underground cables as
per Utility relocation plans and with the approval and technical
specifications of concerned authority including salvage value of
dismantled materials.

i) Water supply line of all types and sizes metre 2423.70

ii) Underground telecom/electric cables metre 1260.05
8.05 Deleted

Rev-04 PAGE 16 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
8.06 Planting of Trees and their Maintenance for two years: Each 542.00
Providing, planting of trees (Avenue trees), height not less than
1.80 meter, digging a hole 0.60 meter in dia and 1.0 meter
deep in the ground by the road side, mixing the soil with
decayed farm yard/sludge mannure, planting the saplings,
backfilling the trench, watering, fixing the tree guard and
maintaining the plants for two years. 50% payment for this item
will be made after one year and remain after two years for the
plants service at that time. The payment made after one year
shall be deducted for plants found dead after two years.

TOTAL AMOUNT BILL NO.8 MISCLLANEOUS CARRIED TO

SUMMARY
BILL NO 9 ELECTRICAL WORKS
9.01 Supply and erection of support of IS standard for over head
lines in truely vertical position including welding, drilling of
required hole etc. including excavation of pole pit, providing
and compacting M-10 Grade concrete in base padding and in
refilling of pole pit , priming with red oxide and painting with
two coat of aluminum paint complete as per MPSEB
specifications.

(A) H, beam 152x152mm,37.1 Kg/mtr

(1) 11 mtr long Each 29934.00
(2) 13 mtr long Each 34867.00
(3) 15 mtr long Each 40016.00
(B) RS JOIST 175X85 MM SIZE
(1) 9.3 mtr long Each 13184.00
9.02 Supply and erection of stay set on existing pole made of GI stay
wire, 19 mm dia. 1.8 mtr. Long stay rod, anchor plate of size
300x300x6.4 mm, thimbale, stay clamp turn buckle,
7/4.00mm dia GI stay wire etc complete including excavation
and refiling the same with concrete of M-10 Grade as per
MPSEB specification.

(A) 16 mm stay set complete Each 1395.00

(B) 20mm stay set complete. Each 2311.00
9.3 Supply and erection of insulator on existing pole with its hard
ware for LT/11kv/33KV lines etc. complete as per MPSEB
specifications.

(a) 11 Kv strain insulator with hardware Each 292.00

(b) 33 Kv pin insulator with hardware Each 522.00
(c ) 11Kv pin insulator with GI Pin Each 194.00
(d) 33 Kv Strain insulator with hard ware (Set of 3) Each 425.00

(e) LT shackle Insulator with hardware, 75X90 mm Each 63.00

(f) 11 KV Polymer Pin Insulator Each 195.00

(g) 33 KV Polymer Pin Insulator Each 522.00
(h) 11 KV Disc Insulator Polymer Each 182.00
(i) 33 KV Disc Insulator Polymer Each 328.00
9.4 Supply and erection fixing of MS angle/channel/flat iron fitting
for existing over head line poles such as cross arms , clamps,
brackets ,nuts bolts etc. including required holes ,welding and
necessary material including priming with red oxide and
painting with two coat of aluminum paint etc complete as per
MPSEB specification.

Rev-04 PAGE 17 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
(A) 33 Kv V cross arm 75x75x6mm, 24.6 kg Each 1874.00
(B) 33 Kv top clamp 75x75x6mm, 3.57 Kg Each 524.00
(C) 11Kv V cross arm, 65X65X6mm angle type 12.34 Kg Each 974.00
(D) 11Kv V Top clam 65X65X6mm angle type 3 Kg Each 279.00
(E) LT 5 pin cross arm 65X65X6mm angle type 22 kg Each 2092.00
(F) LT 4 pin cross arm 50X50X5mm, 8.28 kg Each 1762.00
(G) DC cross arm 5 fit centre 100X50 mm, 65 kg Each 4960.00
(I) DC cross arm 8 fit centre 100X50 mm, 56.31kg Each 2813.00
(J) DO and LA Mounting channel 19.37 kg Each 1476.00
(K) Transformer mounting cross arm 100X50 mm, 52.62 kg Each 4010.00

(L) Transformer belting set 31.0 kg Each 2736.00

(M) Transformer claping set 31kg Each 2736.00
(N) MS Channel 100 X50 mm size KG 63.00
(O) MS nuts and bolts KG 97.00
(P) 33 KV guarding channal, 45.24 kg Set 3447.00
(Q) 11 KV guarding channal, 37.57 kg Set 2863.00
(R) Bracing set for 4" center DP structure Set 3707.00
(S) Bracing set for 8" center DP structure Set 5512.00
(T) H Beam Back Clamp Pair 194.00
(U) Stay Clamp for R.S. Joist/ Stay Clamp A-type/ B-Type Pair 231.00
(V) 11 KV bird Guard Stool Pair 214.00
(W) 33 KV Bird Guard Stool Pair 237.00
(X) Single Pole Cut Point Fitting Set 2312.00
9.5 Supply and drawing of stranded ACSR/AAAC, conductor
confirming to IS –398-1961 of approved make including
stringing, laying, making of complete winding at existing
insulator, jointing, jump-ring, tearing, connecting, testing etc.
complete on existing pole, as per MPSEB specifications.

(A) 100 sq. mm ACSR/AAAC Dog conductor Km 64419.00

(B) 80 Sqmm. ACSR Conductor raccoon Km 50872.00
(C) 55 Sqmm. ACSR Conductor Rabbit Km 34142.00
(D) 34 Sqmm. Weasel Conductor km 22162.00
9.6 Supply and drawing of GI guard wire 13 sqmm (4mm dia)
including stringing winding at existing insulator or brackets,
jointing, with horizontal licingis, connecting etc. as required and
clearing all obstacles, if any, as per MPSEB specifications.

(A) For 33 kv Line Meter 77.00

(B) For 11kv Line Meter 77.00
9.7 Providing and fixing of anticlimbing device of GI barbed wire 2 Each 279.00
ply 12 SWG up to the height of 3.5 mtr. around the pole as per
MPSEB specification.

9.8 Supply and laying spiral-earthing coil made of 13 sq mm. Each 158.00
(4mm)dia GI wire , having spiral dia. 50 mm. with 115 turns,
continuous lead up to 2.5 mtr. fixing on existing pole with MS
nuts and Bolts as per MPSEB specification.

9.9 Supply and fixing of danger caution board enameled marked Each 73.00
for 11 Kv and 33 kv on existing pole as per MPSEB
specification.

9.10 Supply and erection of drop out fuse unit (1 set of 3 nos) as
per MPSEB specification.
(a) 11 KV DO FUSE Set 1652.00
9.11 Supply, installation and testing of (1 set of 3 nos) lightening Each
arrester complete with its hard ware as per MPSEB spcification.

Rev-04 PAGE 18 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
(a) for 11 kv line type Each 425.00
9.12 Supply and erection of aluminum bobbin of LT line on existing Each 36.00
structure etc. complete as per MPSEB specifications.

9.13 Supply and erection of Air break switch as per IS 9920 part I to
V for a normal current rating 400 AMP, spring loaded fixed and
knife type moving contact with complete fitting as per MPSEB
specifications.

(b) 11 KV AB switch Each 6585.00

9.14 Providing,fixing and testing of earthing arrangement with 38.1 Each 5468.00
mm dia. 2.5 mtr. long B class GI pipe electrode including
excavation, packing of char coal and salt as per MPSEB
specification including GI watering pipe 19 mm dia connection
and refilling the pit etc. complete as per MPSEB specification.

9.15 Supply and erection of LT distribution box suitable for 200 kva Each 29245.00
pole mounted distribution transformer complete with mounting
channel, bus bar and MCCB etc. complete as per MPSEB
specification.

9.16 Supply and erection of distribution box suitable for pole

mounted distribution transformer complete with mounting
channel bus bar and MCCB etc. complete as per MPSEB
specification.
(A) 100 KVA Each 16475.00
(B) 63 KVA Each 16345.00
(C) 315 KVA Each 35657.00
(D) 25 KVA Each 6196.00
9.17 Supply erection and testing of PVC insulated heavy duty power
cable confirming to (IS1554-1964 ) of aluminum stranded solid
conductor of 1100 volt grade armoured/ unarmoured.

(a) 4 core 6 SQ mm unarmoured cable Meter 61.00

(b) 3.5 core 70 sqmm Meter 295.00
(c) 3.5 core 150 sqmm Meter 548.00
(d) 3.5 core 300 sqmm Meter 1034.00
9.18 Dismantling and removing of pole by excavation and gas Each Job 1215.00
cutting ,pin/disc insulator ,guarding. angle ,Vcross,top clamp,
ACSR Conductor, any other fitting and placing to MPSEB store
as directed by Engineer and clearing the site including labour
,transportation etc. complete.

9.19 Shifting, installation and testing of distribution transformer of

11/o.4 kv on existing DP structure including connection and
disconnection from HT line and LT panel as required as per
MPSEB specification.

(1) 63 KVA Transformer Each Job 3986.00

(2) 100 KVA Transformer Each Job 3986.00
9.20 Providing and fixing of LT AB Cable Fitting for laying cable on
the pole as per MPSEB specification.
(A)AB Cable Hanging Clamp & Tension Clamp No. 643.95
(B) Suspension Clamp with Attachment No. 437.40
(C ) Clamp for Neutral No. 30.40
(D) LT Dead End Clamp for L.T.A.B CABLE No. 97.20
(E) TENSION CLAMPS (Dead End) No. 546.75
(F) Piercing Connector Type-I No. 91.15
(G) Piercing Connector Type-II No. 109.35
Rev-04 PAGE 19 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
(H) J-Hook for Laying LT AB Cable No. 91.15
(I) J-Hook clamp for Laying LT AB Cable No. 97.20
(J) LT Service connection Ring half round No. 133.65
(K) Spring loaded three Phase bus-bar in insulated box 1 in 5 No. 2965.80
out
(L) Spring loaded single Phase bus-bar in insulated box 1 in 6 No. 1093.00
out
(M) Spring loaded single Phase bus-bar in insulated box 1 in 9 No. 1215.00
out
(N) Spring loaded three Phase bus-bar in insulated box 1 in 3 No. 1517.00
out
(O) Al. Lugs for 150 Sq. Mm. Cable No. 38.88
(P)LT XLPE A.B. cable 3x150+1x95+1x35 sqmm. 1100 v km. 450425.00
(Q)LT XLPE A.B. cable 3x95+1x16+1x50 sqmm. 1100 v km. 212588.55
(R)LT XLPE A.B. cable 3x70+1x16+1x35 sqmm. 1100 v km. 168581.25
9.21 Supply and laying under ground 11/33KV cable for road
crossing with all fitting fixing on existing pole with nuts and
bolts as per MPSEB specification .

(A)33 kv xlpe armoured cable 3x300 sq.mm km. 1846800.00

(B) 33 kv Arial Bunch cable 200 sq.mm km. 1357641.00
(C ) Bimetallic clamp for 33 kv ME Terminal No. 534.60
(D) Indoor heat shrinkable cable jointing kit with lugs for 33kv Set 31152.60
xlpe 3 core 300sq.mm
(E) 33kv Polymer lightening arrestor gapeless type No. 3827.25
(F) Double Gate set of m.s.angle with mesh & locking No. 1822.50
(G) Double suspension strain set Panther conductor No. 3063.00
(H) 11kv Polymer lightening arrestor gapeless type No. 425.25
(I) M.S.Flate 50x6mm MT. 62086.50
(J) 11KV XLPE Armoured cable 3x300 sq.mm km. 1335187.80
(K) 11KV Arial Bunch cable 3x185+1x150 sq.mm. km. 894227.85
(L) 11KV Arial Bunch cable 200x3 sq.mm. mtr. 894.24
(M) Bimetallic clamp No. 534.60
(N) 11KV cable jointing kit with lugs for xlpe 3* 300sq.mm Set 5017.95

(O) G.I.Pipe 150mm B Grade meter 1397.25

(P) G.I.Pipe 150mm A Grade along DP. meter 1172.50
(Q) G.I.Pipe 15mm 3mtr. Length for earthing No. 15185.07
(R ) Hume pipe 150 mm inner dia 30 mm thick meter 498.15
(S) Cable Marker No. 872.00
(T) Boring P/bored 600mm. Dia piles meter 1139.65
9.22 Supply and erection of Isolator switch with handle and Each 18942.00
mechanical locking arrangment 3 phase of multi capacity (1
set of 3 nos ) 3 insulator type 600 Amp.complete as per MPSEB
specifications.

9.23 Supply erecting and testing of PVC/ XLPE insulated heavy duty
power cable conforming to (IS 1554-1964) of alluminum
standerd solid conductor of 1100 V grade armoured/
unarmoured.

(a) PVC 2 core armoured 4 sq.mm. Al. 1100 volts Mtr 48.60
(b) PVC 4 core armoured 10 sq.mm. Al. 1100 volts Mtr 75.00
(c) PVC 3.5 core armoured 35 sq.mm. Al. 1100 volts km 174231.00
(d) PVC 4 core armoured 6 sq.mm. Al. 1100 volts Mtr 60.75
(e) PVC 3.5 core armoured 16 sq.mm. Al. 1100 volts km 94721.40
(f) Xlpe 1 Core Cable 50sq.mm km 42306.30
(g) Erthing set 40mm /ss No. 5467.50
Rev-04 PAGE 20 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
Widening and reconstruction of ……………………………... Road
Bill of Quantities
Item No. Item Unit Quantity Rate (Rs.)
(h) Carpat guarding span 6318.00
(i) 11KV Isolator complete 600 Amp. No. 18941.85
(j) PVC 3.5 core armoured 70Sq.mm Al. conductor 1100V Km. 294759.00
(k) PVC 3.5 core armoured 150Sq.mm Al. conductor 1100V Km. 547661.25

Total Bill No 09

TOTAL GROSS AMOUNT (BILL 1 TO 9)

Rev-04 PAGE 21 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount

Rev-04 PAGE 22 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount

-
-
-
-

-
-
-
-
-

-
-

-
-
-
-
-
-

-
-
-
-
-

Rev-04 PAGE 23 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-

-
-

Rev-04 PAGE 24 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-

Rev-04 PAGE 25 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

Rev-04 PAGE 26 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-
-
-

-
-
-

Rev-04 PAGE 27 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount

-
-
-
-

-
-
-

-
-
-

Rev-04 PAGE 28 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-

-
-
-
-
-

Rev-04 PAGE 29 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-

-
-

Rev-04 PAGE 30 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount

-
-
-

Rev-04 PAGE 31 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-

Rev-04 PAGE 32 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
0.00

Rev-04 PAGE 33 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-
-

Rev-04 PAGE 34 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount

Rev-04 PAGE 35 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

-
-

Rev-04 PAGE 36 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

0.00

-
-

-
-

Rev-04 PAGE 37 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-

0.00

-
-
-

-
-

-
-
-
-

-
-
-
-

Rev-04 PAGE 38 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-
-
-
-
-
-
-
-
-
-

-
-
-
-
-
-
-
-
-
-
-
-
-

-
-
-
-

-
-
-

Rev-04 PAGE 39 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-
-

-
-

-
-
-
-

-
-
-
-
-

-
-
-

-
-
-
-
-
-
-
Rev-04 PAGE 40 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-
-
-
-

-
-
-
-

-
-
-
-

-
-
-
-
-
-
-
-
-
-

-
-
-
-
-
-
-

-
-
-
-
-
-
-
Rev-04 PAGE 41 OF 44
 MP ROAD DEVLOPMENT CORPORATION LIMITED
tion of ……………………………... Road

Amount
-
-
-
-

Rev-04 PAGE 42 OF 44
 MADHYA PRADESH ROAD DEVELOPMENT CORPORATION LIMITED
Widening & Reconstruction of ………………………….. Road
Intermediate Lane
SUMMARY,
Bill Description ORIGINAL CONTRACT
No. Amount in Figure (INR)
A Civil Works
1 Geneal Provision 0.00
2 Site­Clearance 0.00
3 Earthwork 0.00
4 Sub­base, Base Courses 0.00
5 Bituminious & Cement Concrete Pavement 0.00
6 Cross­Drainage structures (Bridges & Culverts) 0.00
7 Traffic Signs, Marking and Road Appurtenances 0.00
(A) Total Cost of Civil Works 0.00
Modifications, if any
Sub­total for Civil Works (A) 0.00
Cost per km for Civil Works 0.00
(B) Non­civil Works
8 Miscellaneous Items 0.00
9 Electric Item 0.00
10 Forest and Environment Clearance
Sub­total for Non­civil Works (B) 0.00
Cost per km 0.00
C Total Cost (A+B) 0.00
D Centages
Provision for variation (Physical Contingencies)@ 5% 0.00
Provision for Escalation (Price Contingencies)@11.25% 0.00
Total Cost of (D) 0.00
E Total Cost (C+D) 0.00
F Maintenace @0.75% per Year of E for 5 Years 0.00
G Total Cost (E+F) 0.00
H Supervision Charges @ 5% of E 0.00
Grand Total (G+I+J) 0.00
Cost per km 0.00

Rev-04
ESH ROAD DEVELOPMENT CORPORATION LIMITED
Length= 65.26 Kms

SUMMARY,
ORIGINAL CONTRACT

Amount in Words (INR)

Rev-04