Revision Assignment 1 (Sunday Only)

INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD

Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on 8 Jan 2024.
 It is compulsory to write assignment in drawing book for all
Q. Write answer to following questions (2marks for each)

(a) Compare front engine front wheel drive (FEFWD) with front engine rear
wheel drive (FERWD) (Any four points).
(b) What is Superstructure of vehicle?
(c) Define vehicle layout. And its types

Q. Write answer to following questions (4 marks for each)

(a) Draw and explain vehicle layout of front engine rear wheel drive.
(b) List different frames used in automobile construction. Write functions of
frame
(c) Compare the FWD and RWD
(d) Draw four wheel drive vehicle state the advantages and disadvantage.
(e) .

Q. Write answer to following questions (6 marks for each)

(a) State the various types of automobiles?

(b) What are the major components of automobile and state the functions of
components?
(c) State the various requirements of automobile body.

“Teachers can open the door, but you must enter it yourself.”
 Revision Assignment 2 (Sunday Only)
INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD
Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on 15 Jan 2024.
 It is compulsory to write assignment in drawing book for all
Q. Write answer to following questions (2marks for each)

(a) Enlist the load acting on frame

(b) Define coefficient of drag and lift
(c) State the function and location of any four components of an automobile.
(d) Draw the diagram of Commercial chassis.

Q. Write answer to following questions (4 marks for each)

(a) Explain the need and the characteristics of CNG.

(b) Explain the working principle of electric vehicles?
(c) Differentiate between Front mount engine and Rear Mount engine
vehicle.
(d) Explain articulated vehicles and rigid vehicles.

Q. Write answer to following questions (6 marks for each)

(a) Differentiate between framed and frameless vehicle.

(b) Explain Hydrogen fuel cell with neat sketch, advantage application
disadvantages and Application.
(c) Explain Frame and construction its type and functions.
(d) With neat sketch give the nomenclature of car body.

“Education is the passport to the future, for tomorrow belongs to those who
prepare for it today.”
 Revision Assignment 3 (Sunday Only)
INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD
Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on 17 FEB 2024.
 It is compulsory to write assignment in drawing book for all
Q. Write answer to following questions (2marks for each)
(a) State working principle of centrifugal clutch
(b) List components of a vehicle counted in sprung and un-sprung weight.
(c) State functions of clutch in automobile.
(d) State working principle of clutch.
(e) State function of transmission system
(f) State the function of clutch
(g) Classify transmission system

Q. Write answer to following questions (4 marks for each)

1. Explain following terms related with car Aerodynamics. i) Drag ii) Lift
2. Write classification frictional clutches
3. List various parts of constant mesh gear box with role of each component.
4. Draw a neat sketch of front engine front wheel type vehicle layout and label it.
5. State four advantages and disadvantages of LPG as a fuel.
6. Difference between single plate clutch and multi plate clutch
7. Draw neat sketch and explain Single plate clutch

Q. Write answer to following questions (6 marks for each)

1) Explain constant mesh gearbox with double Declutching with construction and
working
2) Draw neat sketch and explain multi plate clutch with its advantage, disadvantage and
application.
3) Draw neat sketch of following i)Diaphragm clutch. ii) all-wheel drive iii)FEFWD

“Perfection is not attainable, but if we chase

perfection we can catch excellence.”
 Revision Assignment 4
INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD
Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on .
 It is compulsory to write assignment in drawing book for all
Q. Write answer to following questions (2marks for each)
(h) State need of universal joint and slip joint used in propeller shaft
(i) Define under steering and over steering.
(j) List various parts of synchromesh gear box with role of each component.
(k) State brake fades.
(l) Enlist any four requirements of suspension system in automobile
(m) State factors to be considered while selecting transmission.

Q. Write answer to following questions (4 marks for each)

8. Explain Rack and Pinion type steering gear box with neat sketch
9. Describe working of Disk Brake. Draw a neat sketch.
10. State function and need of independent suspension system.
11. Explain working of ABS.
12. Draw neat sketch and explain Single plate clutch

Q. Write answer to following questions (6 marks for each)

4) Describe torque converter with neat sketch. Compare it with fluid flywheel. (Any 2
points)..
5) State need of ABS. Draw typical layout of ABS. Write in brief role different
components.
6) State significance of live and dead axle. Describe semi floating axle with sketch
7) Sketch the layout of air braking system. Explain its working.
8) Sketch telescopic shock absorber and label main parts.
9) Explain construction and working of bendix drive.
10) Explain construction and working of synchromesh gearbox.

“Don’t give up on your dream.”

 Revision Assignment 5
INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD
Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on .
 It is compulsory to write assignment in drawing book for
Q. Write answer to following questions (4marks for each)

1. Compare Hydraulic brake system and Pneumatic brake system.

2. Compare disc brake and drum brake system.
3. Compare disc brake and drum brake system.
4. Explain Need, requirements and function of steering system.
5. Explain Wheel Geometry :Toe in and Toe out.
Q. Write answer to following questions (4 marks for each)
A. Classify automobiles on the basis of :- i) On the basis of fuel used.ii) On
the basis of capacity.iii) On the basis of Transmission.iv) On
the basis of Drive.
B. Explain working of semi floating rear axle with neat sketch.
C. Explain working of master cylinder with neat sketch.
D. Describe working of wishbone type suspension system with neat sketch.
E. Compare CNG vehicle with LPG vehicle on the basis of following
parameters :-i) Energy content of fuel .ii) Density iii) Chemical formula
of fuel .iv) Application
Q. Write answer to following questions (6 marks for each)
A. Explain construction and working of Epicyclic gear box with neat sketch..
B. Draw the layout of air braking system. Explain it's working.
C. Explain construction and working of differential with neat sketch.
D. Explain the working of Steering linkage for rigid axle suspension vehicle
with neat sketch.

“There are no secrets to success. It results from preparation, hard

work, and learning from failure.”
 Revision Assignment 6
INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD
Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on
 It is compulsory to write assignment in drawing book for all.
Q. Write answer to following questions (4 marks for each)
1. Explain working of gas filled shock absorbers in brief. Draw a simple sketch for the
same
2. Sketch telescopic shock absorber and label main parts.
3. Draw a labled sketch of indicator light circuit and explain its working
4. Explain working of starting system of a vehicle with neat sketch

Q. Write answer to following questions (6 marks for each)

1. Differentiate tubed and tubless tyres.

2. Explain wire harness and describe colour coding used in automobile wiring system
3. Explain passenger comfort and safety
4. List factors affecting tyre life. State the meaning of all terms involved in following tyre
designation. P215 / 65R16 95 H
5. Draw electronic ignition system. Compare it with conventional ignition systems. (Any
four Points).
6. Describe in brief different passenger safety systems adapted in modern vehicles.
7. Explain necessity and importance of Cable Color Codes in automobile.
8. Explain Charging system of a vehicle with neat sketch.
9. Write silent features of Motor Vehicle Act 1989. DraW traffic signs and state meaning.
10. Enlist any four gauges and sensors with their functions.
11. Draw organization structure of Motor Vehicle (RTO) department. Write role of RTO

“Success is the sum of all efforts, repeated day-in & day

out."
 Revision Assignment 7 (Sunday Only)
INSTITUTE OF ENGINEERING AND TENCHOLOGY KANNAD
Course Name: Mechanical Engineering (ME) Semester: ME -6I

Subject: AEN 22656 Prof. Butte Vinod Y.

Instructions:
 Write it on Sunday only.
 It will check on 8 Jan 2024.
 It is compulsory to write assignment in drawing book for all
Q. Write answer to following questions (2marks for each)

1. Write principle of working lead acid battery

2. Enlist any four electrical components of Automobile
3. State necessity of vehicle registration
4. State factors to be considered while selecting transmission.
5. Write principle of working lead acid battery
6. Define HGV and MGV

Q. Write answer to following questions (4 marks for each)

1. Explain working of gas filled shock absorbers in brief. Draw a simple sketch for the
same
2. Explain working of starting system of a vehicle with neat sketch.

Q. Write answer to following questions (6 marks for each)

1. Explain necessity and importance of Cable Color Codes in automobile

2. Explain Charging system of a vehicle with neat sketch
3. Write silent features of Motor Vehicle Act 1989. Draw any 04 traffic signs and state
meaning
4. Enlist any four gauges and sensors with their functions
5. Draw organization structure of Motor Vehicle (RTO) department. Write role of RTO
6. Describe organization structure of motor vehicle department (RTO).
7. Sketch circuit diagram for magneto ignition system
8. Write salient features of motor vehicles Act 1988

"An ounce of patience is worth more than tons of

preaching." – Mahatma Gandhi