Scribd
Upload
20 views

20151707 박기중 HW1

This document is a homework assignment for a structural analysis course, due on March 19, 2025. It includes problems related to calculating normal stress, determining load magnitudes, and finding required diameters for rods under specific stress limits. The document contains calculations and results for various structural scenarios involving loads and materials.

Uploaded by

qkrrlwnd123455
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
20 views

20151707 박기중 HW1

This document is a homework assignment for a structural analysis course, due on March 19, 2025. It includes problems related to calculating normal stress, determining load magnitudes, and finding required diameters for rods under specific stress limits. The document contains calculations and results for various structural scenarios involving loads and materials.

Uploaded by

qkrrlwnd123455
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Structural Analysis (2)

HW 1
Due date: 2025.03.19 (Wed) 11:59 pm.

Answer sheet

1.
(a) .
2 546 MPa
(b) :000N

2. 4 .
4Imm

3. 16877 5N/m .

4. 0 .
001625
1. A solid circular post ABC (see figure) supports a
load P1=1800 N acting at the top. A second load P2 is
uniformly distributed around the shelf at B. The
diameters of the upper and lower parts of the post are
dAB=30 mm and dBC=70 mm, respectively.
(a) Calculate the normal stress σAB in the upper part of
the post.
(b) If it is desired that the lower part of the post have
the same compressive stress as the upper part,
what should be the magnitude of the load P2?

1800N
9) - 546MPa
= 2 .

(30mm)

Pe)
b) 1800N ( +

150mm
= (Commi
9800N = 1800N +P2

- P2 = 800ON
2. Rods AC and BC are used to suspend the 300-kg mass. If each rod is
made of a material for which the average normal stress cannot exceed
150 MPa, determine the minimum required diameter of each rod to the
nearest mm. (θ=50°)

DP =
300ky x 9 .

8 m/sc (f) 2943N =

②FAC = FBC (IHE)

Fy FACX 10358 x2-2943N :


= 0 = 0

= FAC = 2289 .
24761N
24761
2209 .

/50MPa
Ed
: do 4 4/mm.
3. The uniform beam is supported by two rods AB and CD that have
cross-sectional areas of 10 mm2 and 15 mm2, respectively. Determine
the intensity w of the distributed load so that the average normal stress
in each rod does not exceed 300 MPa. (L=8 m)

v
IP
↑3
↑
FAB =
300 X10 = 3000N

F(D =
4500N
300X15 =

4W
P =
twX6 =

[Mazo FIX8 0
PxEx8
- =

&
=
D
- : FLD =
Epow ,
Fab

D w - 2250
& :1687 .
5

- < /687 5 .
N/m
4. When force P is applied to the rigid arm ABC, point B displaces
vertically downward through a distance of 0.4 mm. Determine the normal
strain developed in wire CD. (L1=800 mm, L2=500 mm, L3=400 mm)

800
400
500

O
. 4 MM

a
O
= 0 .
0005

1300 x 0 .
0005 =
0 65
.

0 65
E
.

normalStrain
- =

400

= 0 ,
001622

You might also like