Computer Aided Engineering TE 2024-25

Savitribai Phule Pune University

Faculty of Science & Technology

LAB MANUAL

OF

COMPUTER AIDED ENGINEERING

Third Year
Bachelor of Engineering
(Choice Based Credit System)
Mechanical Engineering
(2019 Course)
Board of Studies – Mechanical and
Automobile Engineering
Zeal College of Engineering and Research

NARHE, PUNE- 411041

Zeal College of Engineering & Research, Pune Page 1

 Computer Aided Engineering TE 2024-25

Laboratory Plan

Pra
ctic
Title of Experiment Session
al
No.

1. 1D Bar Element – Structural Linear Analysis I

2. Truss Analysis using 1D Element II
Plate/Shell Element – Structural Linear and Non-Linear
3. III
Analysis
4. Beam Element – Non-Linear Buckling Analysis IV
5. Thermal Analysis – Static/Transient Analysis V
6. Coupled Analysis- (Structural + Thermal) VI
7. Analysis of Machine Component using 3D Elements VII
8. Non-Linear Analysis of Assembly using Contact Elements VIII
Modal Analysis – Spring -Mass system,
9. IX
simplysupported/Cantilever beam, etc.
Presentation on advanced applications of FEA, NVH, CFD,
10. X
Crash, Fatigue, Manufacturing, etc.

Note:
 Practical 1, 2, 3, 4 and 10 are compulsory.
 Perform any three practical among 5, 6, 7, 8 and 9.
 The lab report shall consist of completion of Practical’s and
Presentations.
 Practical examination shall be based on the practical undertaken
during the semester.
 Practical examination shall cover 20 marks among practical 1 to 4
and 30 marks among practical 5 to 9.
Use of Open-Source Analysis Software is highly recommended.

Zeal College of Engineering & Research, Pune Page 2

 Computer Aided Engineering TE 2024-25

PRACTICAL 1
1D Bar Element – Structural Linear Analysis

Zeal College of Engineering & Research, Pune Page 3

 Computer Aided Engineering TE 2024-25

COMPUTER AIDED ENGINEERING

PRACTICAL - 01

Student Name: ______________________________________________ Roll No.: ___________

Title: 1D Bar Element – Structural Linear Analysis

Problem Statement:

Find deformation, stress, for the 1D bar element using following specifications

Cross section area, A=0.5m*0.5m; Length of Element, Le=5m

P= 1000 N

Geometry or Model:

Zeal College of Engineering & Research, Pune Page 4

 Computer Aided Engineering TE 2024-25

Meshing:

Boundary Condition:

Zeal College of Engineering & Research, Pune Page 5

 Computer Aided Engineering TE 2024-25

Result 1: Deformed Undeformed Shape

Result 2: Nodal Solution Plot

Zeal College of Engineering & Research, Pune Page 6

 Computer Aided Engineering TE 2024-25
Result 3: List Nodal Solution

Result 4: Plot Stresses

Zeal College of Engineering & Research, Pune Page 7

 Computer Aided Engineering
Result 4: List Elemental Stresses TE 2024-25

Zeal College of Engineering & Research, Pune Page 8

 Computer Aided Engineering TE 2024-25

PRACTICAL 2
Truss Analysis using 1D Element

Zeal College of Engineering & Research, Pune Page 9

 Computer Aided Engineering TE 2024-25

PRACTICAL - 02
Student Name: ______________________________________________ Roll No.: ___________

Title: Truss Analysis using 1D Element

Problem Statement:

Determine the displacement, stresses at each element and reaction at support for the
following 2-D truss subjected to plane forces.

Geometry or Model:

Meshing:

Zeal College of Engineering & Research, Pune Page 10

 Computer Aided Engineering TE 2024-25

Boundary Condition:

Result 1: Deformed Undeformed Shape

Zeal College of Engineering & Research, Pune Page 11

 Computer Aided Engineering TE 2024-25

Result 2: Nodal Solution Plot

Zeal College of Engineering & Research, Pune Page 12

 Computer Aided Engineering TE 2024-25

PRACTICAL 3
Plate/Shell Element – Structural Linear and Non-Linear Analysis

Zeal College of Engineering & Research, Pune Page 13

 Computer Aided Engineering TE 2024-25

COMPUTER AIDED ENGINEERING

PRACTICAL - 03

Student Name: ______________________________________________ Roll No.: ___________

Title: Plate/Shell Element – Structural Linear and Non-Linear Analysis

Problem Statement:

Determine the stress distribution over hole plate shown in fig

Geometry or Model:

Zeal College of Engineering & Research, Pune Page 14

 Computer Aided Engineering TE 2024-25

Meshing:

Boundary Condition:

Result 1: Deformed Undeformed Shape

Zeal College of Engineering & Research, Pune Page 15

 Computer Aided Engineering TE 2024-25

Result 2: Nodal Solution Plot

Result 3: List Nodal Solution

Zeal College of Engineering & Research, Pune Page 16

 Computer Aided Engineering TE 2024-25

Zeal College of Engineering & Research, Pune Page 17

 Computer Aided Engineering TE 2024-25

PRACTICAL 4
Beam Element – Non-Linear Buckling Analysis

COMPUTER AIDED ENGINEERING

Zeal College of Engineering & Research, Pune Page 18

 Computer Aided Engineering TE 2024-25

PRACTICAL - 04

Student Name: ______________________________________________ Roll No.: ___________

Title: Beam Element – Non-Linear Buckling Analysis

Problem Statement:

Determine the mode shapes for the cantilever beam shown below of length 1000 mm , cross
sectional area 10*10 mm. E= 2e5, Density 7800.

Geometry or Model:

Meshing:

Zeal College of Engineering & Research, Pune Page 19

 Computer Aided Engineering TE 2024-25

Boundary Condition:

Result 1: Deformed Undeformed Shape for set 1

Zeal College of Engineering & Research, Pune Page 20

 Computer Aided Engineering TE 2024-25

Result 2: Deformed Undeformed Shape for set 2

Result 3: Deformed Undeformed Shape for set 3

Zeal College of Engineering & Research, Pune Page 21

 Computer Aided Engineering TE 2024-25

Result 4: Deformed Undeformed Shape for set 4

Result 5: Deformed Undeformed Shape for set 5

Zeal College of Engineering & Research, Pune Page 22

 Computer Aided Engineering TE 2024-25

Result 6: Result Summary

Zeal College of Engineering & Research, Pune Page 23

 Computer Aided Engineering TE 2024-25

PRACTICAL 5
Thermal Analysis – Static / Transient Analysis

Zeal College of Engineering & Research, Pune Page 24

 Computer Aided Engineering TE 2024-25

COMPUTER AIDED ENGINEERING

PRACTICAL - 05

Student Name: ______________________________________________ Roll No.: ___________

Title: Thermal Analysis – Static / Transient Analysis

Problem Statement:

The Simple Conduction Example is constrained as shown in the

following fig. Thermal conductivity (k) of the material is 10 W/m C and
block is assumed to be infinitely long .

Geometry or Model:

Meshing:
Zeal College of Engineering & Research, Pune Page 25
 Computer Aided Engineering TE 2024-25

Boundary Condition:

Result 1: Solution window

Zeal College of Engineering & Research, Pune Page 26

 Computer Aided Engineering TE 2024-25

Result 2: Nodal Solution Plot

Zeal College of Engineering & Research, Pune Page 27

Result 3: List Nodal Solution Computer Aided Engineering TE 2024-25

Zeal College of Engineering & Research, Pune Page 28

 Computer Aided Engineering TE 2024-25

PRACTICAL 6
Coupled Analysis- (Structural + Thermal)

Zeal College of Engineering & Research, Pune Page 29

 Computer Aided Engineering TE 2024-25

COMPUTER AIDED ENGINEERING

PRACTICAL - 06

Student Name: ______________________________________________ Roll No.: ___________

Title: Coupled Analysis- (Structural + Thermal)

Problem Statement:
A steel link, with no internal stresses, is pinned between two solid structures at a reference
temperature of 0 C (273 K). One of the solid structures is heated to a temperature of 75 C (348
K). As heat is transferred from the solid structure into the link, the link will attempt to expand.
However, since it is pinned this cannot occur and as such, stress is created in the link. A steady-
state solution of the resulting stress will be found to simplify the analysis. Loads will not be
applied to the link, only a temperature change of 75 degrees Celsius. The link is steel with a
modulus of elasticity of 200 GPa, a thermal conductivity of 60.5 W/m*K and a thermal
expansion coefficient of 12e-6 /K.

Geometry or Model:

Zeal College of Engineering & Research, Pune Page 30

 Computer Aided Engineering TE 2024-25

Meshing:

Boundary Condition: Thermal Boundary condition. Temperature on

keypoint 1 = 348 K

Boundary Condition: Structural Boundary condition.

Zeal College of Engineering & Research, Pune Page 31

 Computer Aided Engineering TE 2024-25

Result 1: Deformed Undeformed Shape

Zeal College of Engineering & Research, Pune Page 32

 Computer Aided Engineering TE 2024-25
Result 2: Plot Element table

Zeal College of Engineering & Research, Pune Page 33

 Computer Aided Engineering TE 2024-25

PRACTICAL 7
Modal Analysis –Simply supported/Cantilever beam, etc

COMPUTER AIDED ENGINEERING

Zeal College of Engineering & Research, Pune Page 34

 Computer Aided Engineering TE 2024-25

PRACTICAL - 07
Student Name: ______________________________________________ Roll No.: ___________

Title: Modal Analysis – Spring -Mass system, simply supported/Cantilever

beam

Problem Statement:

Determine the mode shapes for the cantilever beam shown below of length 1000 mm , cross
sectional area 100*120 mm. E= 2e5, Density 7800.

Geometry or Model:

Zeal College of Engineering & Research, Pune Page 35

 Computer Aided Engineering TE 2024-25
Meshing:

Boundary Condition:

Zeal College of Engineering & Research, Pune Page 36

 Computer
Result 1: Deformed Undeformed Aided
Shape for setEngineering
1 TE 2024-25

Result 2: Deformed Undeformed Shape for set 2

Zeal College of Engineering & Research, Pune Page 37

 Computer
Result 3: Deformed Undeformed Shape for Aided
set 3 Engineering TE 2024-25

Result 4: Deformed Undeformed Shape for set 4

Result 5: Deformed Undeformed Shape for set 5

Zeal College of Engineering & Research, Pune Page 38

 Computer Aided Engineering TE 2024-25

Zeal College of Engineering & Research, Pune Page 39