*** Lead chart ***

NAME OF WORK:- Name of Work: Providing CAD for LIS Dulehar (T/well No.112) and LIS Pubowal in Teh.
Haroli Distt. Una(HP). (SH: System deficiency correction by drilling and developing of 1
No. T/well in place of defunct T/well Pubowal (T/well Aujle).

1) Carriage of M.S Pipe 300mm and 200mm dia from Gaziabad :-

Gaziabad Nangal Dam Railway station Site of work
BY RAIL BY Mechanical Transport
372 20
KM KM
1) Carriage of V-wire screen 300mm and 200mm dia from Divisional store :-
Divisional store Site of work
BY Mechanical Transport
25
KM

Certified that the lead taken in the lead chart is shotest and economical routes by all means.

sd/-
ASSISTANT ENGINEER EXECUTIVE ENGINEER,
JAL SHAKTI DIVISION TAHLIWAL JAL SHAKTI DIVISION 1 UNA

*** CARRIAGE OF MATERIALS ***

NAME OF WORK :- Name of Work: Providing CAD for LIS Dulehar (T/well No.112) and LIS Pubowal in Teh.
Haroli Distt. Una(HP). (SH: System deficiency correction by drilling and developing of 1
No. T/well in place of defunct T/well Pubowal (T/well Aujle).

300mm dia M.S. Pipe . 200mm dia M.S. Pipe .

Unit : 100 Rmt Unit : 100 Rmt
LEAD : By Mech. 20.00 Km. LEAD : By Mech. 20.00 Km.
By Head : 0.00 Km. By Head : 0.00 Km.
1) By Mech. Nos. Rate/ Km. 1) By Mech. Nos. Rate/ Km.
1 Km. 0 1405.30 0.00 1 Km. 0 796.34 0.00
2 Km. 0 1635.97 0.00 2 Km. 0 927.05 0.00
3 Km. 0 1864.26 0.00 3 Km. 0 1056.41 0.00
4 Km. 0 2086.66 0.00 4 Km. 0 1182.44 0.00
5 Km. 1 2299.36 2299.36 5 Km. 1 1302.97 1302.97
5- 10 Km. 5 197.93 989.65 5- 10 Km. 5 112.16 560.80
10-20 Km. 10 167.90 1679.00 10-20 Km. 10 95.15 951.50
Beyond 20 Km. 0 143.60 0.00 Beyond 20 Km. 0 81.38 0.00
4968.01 2815.27
Cost of 100 Rmt. 4968.01 Cost of 100 Rmt. 2815.27
Cost of 1 Rmt. 49.68 Cost of 1 Rmt. 28.15
300mm dia V-wire screen. 200mm dia V-wire screen.
Unit : 100 Rmt Unit : 100 Rmt
LEAD : By Mech. 25.00 Km. LEAD : By Mech. 25.00 Km.
By Head : 0.00 Km. By Head : 0.00 Km.
1) By Mech. Nos. Rate/ Km. 1) By Mech. Nos. Rate/ Km.
1 Km. 0 1405.30 0.00 1 Km. 0 796.34 0.00
2 Km. 0 1635.97 0.00 2 Km. 0 927.05 0.00
3 Km. 0 1864.26 0.00 3 Km. 0 1056.41 0.00
4 Km. 0 2086.66 0.00 4 Km. 0 1182.44 0.00
5 Km. 1 2299.36 2299.36 5 Km. 1 1302.97 1302.97
5- 10 Km. 5 197.93 989.65 5- 10 Km. 5 112.16 560.80
10-20 Km. 10 167.90 1679.00 10-20 Km. 10 95.15 951.50
Beyond 20 Km. 5 143.60 718.00 Beyond 20 Km. 5 81.38 406.90
5686.01 3222.17
Cost of 100 Rmt. 5686.01 Cost of 100 Rmt. 3222.17
Cost of 1 Rmt. 56.86 Cost of 1 Rmt. 32.22

sd/-
ASSISTANT ENGINEER EXECUTIVE ENGINEER,
JAL SHAKTI DIVISION TAHLIWAL JAL SHAKTI DIVISION 1 UNA
CARRIAGE OF MATERIAL BY MECHANICAL TRANSPORT
Sl.No Average speed No.of No.of Litre of Litre of Litres of Cost of Cost of Hire Total Cost per Increas Average
.Lea Km/hour(s) Trips No. Km. diesel Diesel @ M.Oil M.Oil @ 6 Charges cost trip e in cost per
d done consumed per Ltr. consume per litre Beldarof Truck Col.No6 Cost addition
inK. 2NL+6 d @ per @ per +8+9+1 per Km al
M.(L) day day 0 over Km.after
previou five Km.
s Km.
79.00 270.00 350.00 2325.00
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 12.00 5.65 17.30 5.77 455.83 0.22 59.40 2100.00 2325.00 4940.23 874.38
2 12.75 5.12 26.48 8.83 697.57 0.33 89.10 2100.00 2325.00 5211.67 1017.90 143.52
3 13.12 4.69 34.14 11.38 899.02 0.43 116.10 2100.00 2325.00 5440.12 1159.94 142.04
4 13.50 4.34 40.72 13.57 1072.03 0.51 137.70 2100.00 2325.00 5634.73 1298.32 138.38
5 13.88 4.06 46.60 15.53 1226.87 0.58 156.60 2100.00 2325.00 5808.47 1430.66 132.34
6 14.25 3.82 51.84 17.28 1365.12 0.65 175.50 2100.00 2325.00 5965.62 1561.68 131.02
7 14.63 3.62 56.68 18.89 1492.31 0.71 191.70 2100.00 2325.00 6109.01 1687.57 125.89
8 15.10 3.46 61.36 20.45 1615.55 0.77 207.90 2100.00 2325.00 6248.45 1805.91 118.34
9 15.38 3.31 65.58 21.86 1726.94 0.82 221.40 2100.00 2325.00 6373.34 1925.48 119.57
10 15.75 3.17 69.40 23.13 1827.27 0.87 234.90 2100.00 2325.00 6487.17 2046.43 120.95 123.15
11 16.13 3.06 73.32 24.44 1930.76 0.92 248.40 2100.00 2325.00 6604.16 2158.22 111.79
12 16.50 2.96 77.04 25.68 2028.72 0.96 259.20 2100.00 2325.00 6712.92 2267.88 109.66
13 16.88 2.87 80.62 26.87 2122.73 1.01 272.70 2100.00 2325.00 6820.43 2376.46 108.58
14 17.25 2.78 83.84 27.95 2208.05 1.05 283.50 2100.00 2325.00 6916.55 2487.97 111.51
15 17.63 2.71 87.30 29.10 2298.90 1.09 294.30 2100.00 2325.00 7018.20 2589.74 101.77
16 18.00 2.64 90.48 30.16 2382.64 1.13 305.10 2100.00 2325.00 7112.74 2694.22 104.48
17 18.38 2.58 93.72 31.24 2467.96 1.18 318.60 2100.00 2325.00 7211.56 2795.18 100.96
18 18.75 2.52 96.72 32.24 2546.96 1.21 326.70 2100.00 2325.00 7298.66 2896.29 101.11
19 19.13 2.47 99.86 33.29 2629.91 1.25 337.50 2100.00 2325.00 7392.41 2992.88 96.59
20 19.50 2.42 102.80 34.27 2707.33 1.29 348.30 2100.00 2325.00 7480.63 3091.17 98.29 104.47
21 19.88 2.38 105.96 35.32 2790.28 1.32 356.40 2100.00 2325.00 7571.68 3181.38 90.21
22 20.25 2.34 108.96 36.32 2869.28 1.36 367.20 2100.00 2325.00 7661.48 3274.14 92.76
23 20.63 2.30 111.80 37.27 2944.33 1.40 378.00 2100.00 2325.00 7747.33 3368.40 94.26
24 21.00 2.26 114.48 38.16 3014.64 1.43 386.10 2100.00 2325.00 7825.74 3462.72 94.32
25 21.38 2.23 117.50 39.17 3094.43 1.48 399.60 2100.00 2325.00 7919.03 3551.13 88.41
26 21.75 2.20 120.40 40.13 3170.27 1.51 407.70 2100.00 2325.00 8002.97 3637.71 86.58
27 22.13 2.17 123.18 41.06 3243.74 1.54 415.80 2100.00 2325.00 8084.54 3725.59 87.88
28 22.50 2.14 125.84 41.95 3314.05 1.57 423.90 2100.00 2325.00 8162.95 3814.46 88.87
29 22.88 2.11 128.38 42.79 3380.41 1.60 432.00 2100.00 2325.00 8237.41 3903.99 89.53
30 23.25 2.09 131.40 43.80 3460.20 1.64 442.80 2100.00 2325.00 8328.00 3984.69 80.70 89.35
 CARRIAGE OF MATERIAL BY MECHANICAL TRANSPORT INCLUDING LOADING/UNLOADINGAND STACKING OF MATERIALS
S.No MATERIALS CAPACITY NET UNITS COST PER UNIT MATERIAL/DISTANCE GIVEN BELOW
QTY.TO BE BEYOND BEYOND
PAID 1 Km. 2Km. 3Km. 4Km. 5Km. BEYOND 20Km
5Km.UP 10Km.UP
AFTER TO 10 Km. TO 20 Km.
/Km.
DEDUCTIO
N OF
VOIDS. 874.38 1017.90 1159.94 1298.32 1430.66 123.15 104.47 89.35
1 2 3 4 5 6 7 8 9 10 11 12 13
1 Lime, moorum , 6 cu.m 6.00 1 cu.m 145.73 169.65 193.32 216.39 238.44 20.53 17.41 14.89
building rubish.
2 Earth work. 6 cu.m 4.80 1 cu.m 182.16 212.06 241.65 270.48 298.05 25.66 21.76 18.61

3 Manure or sludge 6 cu.m 5.52 1 cu.m 158.40 184.40 210.13 235.20 259.18 22.31 18.93 16.19

4 Excavated rock. 6 cu.m 3.00 1 cu.m 291.46 339.30 386.65 432.77 476.89 41.05 34.82 29.78
5 Sand,stone agg. below 5 cu.m 5.00 1 cu.m 174.88 203.58 231.99 259.66 286.13 24.63 20.89 17.87
40mm
6 Stone agg.40mm & 5 cu.m 4.62 1 cu.m 189.26 220.32 251.07 281.02 309.67 26.66 22.61 19.34
above,build. Stones.
7 Soling stone, stone 5 cu.m 4.25 1 cu.m 205.74 239.51 272.93 305.49 336.63 28.98 24.58 21.02
block & stone for filling
crates
8 Bricks. 2000Nos. 2000.00 1000 Nos. 437.19 508.95 579.97 649.16 715.33 61.58 52.24 44.68

9 Bricks tiles. 3200Nos. 3200.00 1000 Nos. 273.24 318.09 362.48 405.73 447.08 38.48 32.65 27.92

10 Slates. 14450Nos. 14450.00 1000 Nos. 60.51 70.44 80.27 89.85 99.01 8.52 7.23 6.18

11 Terrazzo Tiles. 2500Nos. 2500.00 1000 Nos. 349.75 407.16 463.98 519.33 572.26 49.26 41.79 35.74

12 Cement G.I. CI. AC. CC 7.50 Tonne 7.50 1 Tonne 116.58 135.72 154.66 173.11 190.75 16.42 13.93 11.91
pipes below 100mm dia
& other heavy
materials.
13 Steam Coal 5.5 Tonne 5.50 1 Tonne 158.98 185.07 210.90 236.06 260.12 22.39 18.99 16.25
14 Steel i/c C.G.I & 7.50 Tonne 7.50 1 Tonne 116.58 135.72 154.66 173.11 190.75 16.42 13.93 11.91
A.C.sheet.

15 Timber 5 cu.m 5.00 1 cu.m 174.88 203.58 231.99 259.66 286.13 24.63 20.89 17.87

16 Tar Bitumen etc. 4.50 Tonne 4.50 1 Tonne 194.31 226.20 257.76 288.52 317.92 27.37 23.22 19.86

17 R.C.C.,A.C. Hume, steel 329.40m 329.40 100m 265.45 309.02 352.14 394.15 434.32 37.39 31.72 27.13
C.I.Pipes:- 80 mm dia
18 100 mm dia 292.80m 292.80 100m 298.63 347.64 396.15 443.42 488.61 42.06 35.68 30.52

19 125 mm dia 219.6m 219.60 100m 398.17 463.52 528.21 591.22 651.48 56.08 47.57 40.69

20 150 mm dia 183m 183.00 100m 477.80 556.23 633.85 709.46 781.78 67.30 57.09 48.83

21 200 mm dia 109.80m 109.80 100m 796.34 927.05 1056.41 1182.44 1302.97 112.16 95.15 81.38
22 250 mm dia 80.52m 80.52 100m 1085.92 1264.16 1440.56 1612.42 1776.78 152.94 129.74 110.97

23 300 mm dia 62.22m 62.22 100m 1405.30 1635.97 1864.26 2086.66 2299.36 197.93 167.90 143.60

24 350 mm dia 43.92m 43.92 100m 1990.85 2317.62 2641.03 2956.10 3257.42 280.40 237.86 203.44

25 400 mm dia 32.94m 32.94 100m 2654.46 3090.16 3521.37 3941.47 4343.23 373.86 317.15 271.25

26 450 /500mmdia 25.62m 25.62 100m 3412.88 3973.07 4527.48 5067.60 5584.15 480.68 407.77 348.75

27 600, 700, 750 & 800 18.30m 18.30 100m 4778.03 5562.30 6338.47 7094.64 7817.81 672.95 570.87 488.25
mm dia
28 900,1000,1100 & 1200 11.00m 11.00 100m 7948.91 9253.64 10544.91 ### 13006.00 1119.55 949.73 812.27
mm dia.

EXECUTIVE ENGINEER,
JAL SHAKTI DIVISION 1 UNA
 CARRIAGE OF MATERIAL BY MANUAL LABOUR INCLUDING LOADING/UNLOADINGAND STACKING OF MATERIALS
S. MATERIALS CAPACIT NET UNITS COST OF COST OF CARRIGE INCLUDING LOADING AND STACKING
No Y QTY.TO 8
FOR FOR FOR 100 FOR 1 BEYOND
BE PAID HOURS
FIRST 50 EVERY MTR KM. 1
AFTER
MTR ADD. LEAD KM./EVE
DEDUCT
OF 50 RY 1/2
ION OF
MTRS OR KM.
VOIDS.
PART
THERE OF
BEYOND
1 2 3 4 5 6 7 8 9 10 11
LIGHT MATERIALS 7.67 No's Beldar @ 320.83 2460.77 B : =(Col.No.7/2+Col.No.7*1.40/2) 2952.92
1 Lime, moorum and building 35 cu.m 35.00 1 cu.m 2460.77 84.37 35.15 119.52 752.22 376.11
2 rubish.
.Earth work. 35 cu.m 28.00 1 cu.m 2460.77 105.46 43.94 149.40 940.32 470.16
3 Manure or sludge 35cu.m 32.20 1 cu.m 2460.77 91.71 38.21 129.92 817.70 408.85
4 Excavated rock. 35 cu.m 17.50 1 cu.m 2460.77 168.74 70.31 239.05 1504.63 752.32
5 Sand,stone agg.below 40mm 28 cu.m 28.00 1 cu.m 2460.77 105.46 43.94 149.40 940.32 470.16
size.
6 Stone agg.40mm & above,build. 28 cu.m 25.90 1 cu.m 2460.77 114.01 47.51 161.52 1016.70 508.35
Stones.
7 Soling stone, stone block & 28 cu.m 28.00 1 cu.m 2460.77 105.46 43.94 149.40 940.32 470.16
stone for filling crates
8 Bricks. 15000 15000.00 1000 2460.77 196.86 82.03 278.89 1755.43 877.72
Nos Nos.
9 Bricks tiles. 24000 24000.00 1000 2460.77 123.04 51.27 174.31 1097.17 548.59
10 Slates. Nos.
80000 80000.00 Nos.
1000 2460.77 36.91 15.38 52.29 329.13 164.57
Nos. Nos.
11 Terrazzo Tiles. 15000 15000.00 1000 2460.77 196.86 82.03 278.89 1755.43 877.72
HEAVY MATERIALS Nos
9.20 Nos.
No's Beldar @ 320.83 2951.64 B : =(Col.No.7/2+Col.No.7*1.40/2) 3541.97
1 Stone blocks G.I,C.C. pipes 46 Tonne 46.00 1 Tonne 2951.64 77.00 32.08 109.08 686.52 343.26
below 100mm dia and other
heavy materials.
2 cement 57 Tonne 57.00 1 Tonne 2951.64 62.14 25.89 88.03 554.05 277.03
3 Steel including C.G.I & asbestos 27 Tonne 27.00 1 Tonne 2951.64 131.18 54.66 185.84 1169.72 584.86
sheet.
4 Timber 42 cu.m 42.00 1 cu.m 2951.64 84.33 35.14 119.47 751.99 376.00
5 Tar Bitumen etc. 46 Tonne 46.00 1 Tonne 2951.64 77.00 32.08 109.08 686.52 343.26
6 Concrete, R.C.C. Hume, steel 1702m 1702.00 100m 2951.64 208.11 86.71 294.82 1855.60 927.80
C.I.Pipes:- 100mm dia
7 Concrete, R.C.C. Hume, steel 1391m 1391.00 100m 2951.64 254.63 106.10 360.73 2270.53 1135.27
C.I.Pipes:- 125mm dia
8 Concrete, R.C.C. Hume, steel 1208m 1208.00 100m 2951.64 293.21 122.17 415.38 2614.44 1307.22
C.I.Pipes:- 150mm dia
9 Concrete, R.C.C. Hume, steel 805m 805.00 100m 2951.64 440.00 183.33 623.33 3923.27 1961.64
C.I.Pipes:- 200mm dia
10 Concrete, R.C.C. Hume, steel 458m 458.00 100m 2951.64 773.36 322.23 1095.59 6895.73 3447.87
C.I.Pipes:- 250mm dia
11 Concrete, R.C.C. Hume, steel 366m 366.00 100m 2951.64 967.75 403.23 1370.98 8629.12 4314.56
C.I.Pipes:- 300mm dia
12 Concrete, R.C.C. Hume, steel 256m 256.00 100m 2951.64 1383.58 576.49 1960.07 12336.89 6168.45
C.I.Pipes:- 350mm dia
13 Concrete, R.C.C. Hume, steel 220m 220.00 100m 2951.64 1609.99 670.83 2280.82 14355.76 7177.88
C.I.Pipes:- 400mm dia
14 Concrete, R.C.C. Hume, steel 165m 165.00 100m 2951.64 2146.65 894.44 3041.09 19141.01 9570.51
C.I.Pipes:- 450mm,500mm dia

15 Concrete, R.C.C. Hume, steel 150m 150.00 100m 2951.64 2361.31 983.88 3345.19 21055.03 10527.52
C.I.Pipes:- 600,700,750 &
800mm dia
16 Concrete, R.C.C. Hume, steel 125m 125.00 100m 2951.64 2833.58 1180.66 4014.24 25266.12 12633.06
C.I.Pipes:-
900,1000,1100&1200mm dia
17 Asbestes cement pipes: - 10064m 10064.00 100m 2951.64 35.19 14.66 49.85 313.73 156.87
50mm dia =5032 pipes of 2m
length 10064m
18 As bestes cement pipes: - 80mm 3660m 3660.00 100m 2951.64 96.78 40.32 137.10 862.86 431.43
dia 1620 pipes of 2m
length=3660
19 As bestes cement pipes:- 2562m 2562.00 100m 2951.64 138.25 57.60 195.85 1232.65 616.33
100mm dia 1281 pipes of 2m
length=2562m
20 As bestes cement pipes:- 2200m 2200.00 100m 2951.64 161.00 67.08 228.08 1435.52 717.76
125mm dia 1100 pipes of 2m
length= 2200m
21 As bestes cement pipes:- 1830m 1830.00 100m 2951.64 193.55 80.65 274.20 1725.90 862.95
150mm dia 915 pipes of 2m
length =1830m
22 As bestes cement pipes:- 1600m 1600.00 100m 2951.64 221.37 92.24 313.61 1973.93 986.97
200mm dia 800 pipes of 2m
length= 1600m

23 As bestes cement pipes:- 1400m 1400.00 100m 2951.64 253.00 105.42 358.42 2255.98 1127.99
250mm dia 700 pipes of 2m
length= 1400m

24 As bestes cement pipes:- 1200m 1200.00 100m 2951.64 295.16 122.99 418.15 2631.97 1315.99
300mm dia 600 pipes of 2m
length= 1200m
RATE OF AIR VALVE 4148 Each
CLASS OF A.VALVE PN-10
DIA. OF A.VALVE 25 mm
RATE OF G.I. PIPE (M) 75 Rmt

ANALYSIS OF RATE
P/F C.I. air valve ( PN-10) of Leader make, test pr. 11.22 Kg/cm2.
( BS 1452-90)
( Detail for 10 Nos.)
S.No. DESCRIPTION OF ITEM QTY. RATE UNIT AMT.

Material:-
1 CI air valve 25 mm 10.00
Add 16% EXCIDE DUTY.
Add 4% HP S.T.
Inspection charges @ 1%

2 GMS tube 25 mm dia (M) for installing air valve

1.50
3 Making hole in R/main of diff. Dia & welding
of 25 mm dia pipe in two layers Job

4 Carriage Job

5 Labour for fixing air valve I/c white lead & spun yarn
Job

Total

Add 10% C.P. & 5% O.H.C. on all

except 3, 4 & 5 i.e. on Rs. 45392.07
 Test Pressure of 52.00 kg/cm^2
Class ASA-300
Rate of R/valve 28832.00 each
Reflux valve 125 mm dia
Sluice valve 125 mm dia
F. table 28
Wt of joint 19.592 Kg
Rate of flanges 59.00 Kg
welding rate 1.50 cm
Gasket sheet 40.00 each
Fitter 121.33 each
A/Fitter 96.25 each
Beldar 75.83 each
Outer dia 139.70 mm
Wt. of valve 100.00 Kg

ANALYSIS OF RATE

P/F Reflux valve Class ASA-300 of Leader make

Test Pressure of 52.00 kg/cm^2

Detail for 10 Nos.

S.No. Description Qty.

Material:_

1) ASA-300 125 mm 10.00

Reflux valve Add 16.32 % Excise duty

Add 4 % H.P.S.T.+4 % C.S.T

Add 1 %Inspection Charges

Add Freight charges(from factory to

nearest road side/site of work)

2) MS flanges table 28

Wt.of joints for 195.92 Kg 195.92

Nos.valves Add 4% S.T.

3) Welding charges =2 x2x2x10x3.141x 139.70 3510.38

4) Gasket sheet 20.00

5) Carriage of flanges & valves

BY MECH ANICAL TPT. 14.00 KM 0.19592

BY HEAD LOAD 1.00 KM 0.19592

6) Labour

Labour for fixing valves for 700 Kg

Fitter 1.12 121.33 each 135.89

A/Fitter 0.74 96.25 each 71.23

Beldar 2.98 75.83 each 225.97

Sundries LS 43.31

Total 476.40

Cost per Kg 0.681

Cost for fixing 10 No. Valves 1000.00

7) Labour for 10 No. joints

Fitter 0.30 121.33 each 36.40

A/Fitter 0.30 96.25 each 28.88

Beldar 1.20 75.83 each 91.00

Total 156.27 10.00

 Add 10% CP on all amount 363514.49

Add 5% OHC on all amount 375536.15

DRILLING EQUIPMEN 2100.00 /DAY

DETONATOR 200.00 /100 Nos.
S.F.COIL. 20.00 /COIL
SPECIAL GELATINE 45.00 KG
BELDAR 75.83 /DAY
BHISTI 75.83 /DAY
HOLE DRILLER 75.83 /DAY
BLASTER 75.83 /DAY

ANALYSIS OF RATE
Exc. In foundation & trenches etc. in earth work, lift upto 1.50 mts.
in P.J. work (50% each) in all leads & lifts
Detail for 10 Cum
SNo. Description of item Qty

PICK WORK:-
(A) Labour Beldar 8.32
Bhisti 0.28
 Add 1.5% water charges

Add 10% CP & 5% OHC

COST PER CUM

B Jumper work
a) Material:Drilling equipment 0.045
Special gelatine(80 %) 0.63
Detonator(Ordinary) 3.00
SF Coil (10 Mts.length) 0.25
b) Labour:-Driller 0.135
Blaster 0.09
Beldar 16.00

Add 10% CP & 5% OHC

Average rate for P.J.W.

50% each (a+b)/2

ANALYSIS OF RATE

DISMENTALLING OF OLD GMS TUBES FROM TRENCHES ETC

(Excluding earth work)
GMS TUBES 50 mm dia.
S.No. DECRIPTION QTY.
(A) LABOUR

Beldar 0.40

Plumber/Fitter 0.19

Add 10% CP & 5% OHC= 53.38

DIESEL 26.84 / LTS.

M/OIL 90.00 / LTS.
HIRING CHARGES 300.00 / DAY
OF PUMP
P.OPERATER 121.33 PER DAY

ANALYSIS OF RATE
BAILING OUT OR PUMPING OUT WATER DURING EXCAVATION IN FOUNDATION &
TRENCHES IN EARTH WORK. (QTY.OF.WATER CLOSING IN FOUND
PUMPING OPERATION :- (200 CUSECS)
PUMPS ARE TO BE APPLIED (ONE ACT AS STAND BY)
COST OF BAILING OUT WATER IN 12 HOURS i.e. ONE PUMP FOR 12 HOURS
SNo. Description Qty.

(A) MATERIAL
DIESEL 36.00
M/OIL 0.50
 HIRE CHARGES OF PUMPS 2.00
(B) LABOUR
P.OPERATER
(1 NO. FOR 8 HOURS) 1.50

ADD 10 %C.P. & 5% O.H.C. 1793.24

COST FOR 14 CUM

COST PER ONE CUM

EXCAVATION IN EARTH WORK (P.J. 50 % EACH)

DEWATERING/BAILNG OUT WATER DURING EXCAVATION

WT. OF PIPE 6.16 KG

DIA. OF PIPE 65 mm
PLUMBER/FITTER 121.33 /DAY
BELDAR 75.83 /DAY
PLUMBER/FITTER 0.30 EACH
BELDAR 0.79 EACH
M.LEAD FOR GMS T 32.00 KM
H.LEAD FOR GMS T 0.50 KM
RATES BY MECH.TPT 198.24 /MT
RATES BY HEAD LO 86.42 /MT

ANALYSIS OF RATE

LAYING,JOINTING AND TESTING IN TRENCHES G.M.S. TUBE (LIGHT

CLASS) INCLUDINGTUBE FITTING (EARTH WORK IN TRENCHES

TO BE MEASURED & PAID FOR SEPARATLY

S.No. DECRIPTION

(A) LABOUR

Beldar

Plumber/Fitter
 ADD FOR WHITE STIFF & HEMP OIL

(B) EXTRA CARRIAGE OF GMS TUBE

M.LEAD FOR GMS TUBE 32.00 KM

H.LEAD FOR GMS TUBE 0.50 KM

ADD 10 % CP & 5 % OHC ON ALL AMOUNT

WT. OF PIPE 10.51 KG

DIA. OF PIPE 100 mm 15mm TO 20 mm
PLUMBER/FITTER 121.33 /DAY 25mm TO 32 mm
BELDAR 75.83 /DAY 40mm TO 50 mm
PLUMBER/FITTER 0.40 EACH 65mm TO 80 mm
BELDAR 1.19 EACH 100mm
M.LEAD FOR GMS T 32.00 KM 125mm
H.LEAD FOR GMS T 0.50 KM 150mm
RATES BY MECH.TPT 508.00 MT
RATES BY HEAD LO 233.70 MT
ANALYSIS OF RATE
LAYING,JOINTING AND TESTING IN TRENCHES G.M.S. TUBE (LIGHT CLASS) INCLUDING
TUBE FITTING (EARTH WORK IN TRENCHES TO BE MEASURED & PAID FOR SEPARATL

S.No. DECRIPTION QUANTITY

MATERIAL

DETAILS OF GMS TUBES 10.00 RMT

ADD 2 % FOR BENDS ETC. 0.20 RMT

TOTAL 10.20 RMT

(A) LABOUR
Beldar
Plumber/Fitter
ADD FOR WHITE STIFF & HEMP OIL

(B) EXTRA CARRIAGE OF GMS TUBE

M.LEAD FOR GMS TUBE 32.00 KM
H.LEAD FOR GMS TUBE 0.50 KM

ADD 10 % C.P. & 5 % O.H.C. ON ALL AMOUNT

BROKEN STONE 50 232.80 CUM RATE BY MECH.LEAD FOR B/STONE 50

BAZRI 20 TO 25 mm 288.60 CUM RATES BY HEAD LEAD FOR B/STONE 50
BAZRI 6 TO 20 mm 343.80 CUM RATES BY MECH.LEAD FOR BAJRI 20 T
 COURSED SAND 3 m 132.00 CUM RATES BY HEAD LEAD FOR BAJRI 20 TO
FINE SAND 0.2 mm 144.00 CUM RATES BY MECH.LEAD FOR BAJRI 6 TO
MECH.LEAD FOR B/S 40.00 KM RATES BY HEAD LEAD FOR BAJRI 6 TO
HEAD LEAD FOR B/S 0.50 KM RATES BY MECH.LEAD FOR COURSED S
MECH.LEAD FOR BAJ 40.00 KM RATES BY HEAD LEAD FOR COURSED S
HEAD LEAD FOR BAJR 0.50 KM RATES BY MECH.LEAD FOR FINE SAND 0
MECH.LEAD FOR BAJ 40.00 KM RATES BY HEAD LEAD FOR FINE SAND 0
HEAD LEAD FOR BAJR 0.50 KM
MECH.LEAD FOR CO 40.00 KM
HEAD LEAD FOR COU 0.50 KM
MECH.LEAD FOR FINE 17.00 KM
HEAD LEAD FOR FINE 0.50 KM

ANALYSIS OF RATE

PROV. & PLACING IN HORIZENTAL LAYERS FILTERING MEDIA DULY GRADED,

SCREENED,WASHED & CLEANED AS SPECIFIED BY ENGINEER -IN -CHARGE

SNo. DESCRIPTION OF ITEM QTY.
1) MATERIAL:-
A) IST LAYER:-BROKEN STONE DULY SCREENED,WASHED 1.00
& GRADED FROM 50 mm TO 75 mm
B) CARRIAGE:-
MECH.LEAD FOR B/STONE 50 T 40.00 KM 1.00
HEAD LEAD FOR B/STONE 50 T 0.50 KM 1.00

C) LABOUR:-

ADD 10 % C.P. & 5 % O.H.C. ON Rs. 789.18

2) MATERIAL:-
A) 2nd LAYER:-BROKEN STONE DULY SCREENED, 1.00
 WASHED& GRADED FROM 20 mm TO 25 mm
B) CARRIAGE:-
MECH.LEAD FOR BAJRI 20 TO 25 mm 40.00 KM 1.00
HEAD LEAD FOR BAJRI 20 TO 25 mm 0.50 KM 1.00

C) LABOUR:-

ADD 10 % C.P. & 5 % O.H.C. ON Rs. 806.99

3) MATERIAL:-
A) 3rd LAYER:-BROKEN STONE DULY SCREENED,WASHED 1.00
& GRADED FROM 6 mm TO 20 mm
B) CARRIAGE:-
MECH.LEAD FOR BAJRI 6 TO 2 40.00 KM 1.00
HEAD LEAD FOR BAJRI 6 TO 20 0.50 KM 1.00

C) LABOUR:-

ADD 10 % C.P. & 5 % O.H.C. ON Rs. 862.19

4) MATERIAL:-
A) 4th LAYER:-BROKEN STONE DULY SCREENED,WASHED 1.00
& GRADED FROM 3 mm TO 6 mm
B) CARRIAGE:-
MECH.LEAD FOR COURSED SAN 40.00 KM 1.00
HEAD LEAD FOR COURSED SAN 0.50 KM 1.00

C) LABOUR:-
 ADD 10 % C.P. & 5 % O.H.C. ON Rs. 637.28

5) MATERIAL:-
A) BOTTOM LAYER:-BROKEN STONE DULY SCREENED,WASHE 1.00
& GRADED FROM .02 mm TO 0.4 mm
B) CARRIAGE:-
MECH.LEAD FOR FINE SAND 0.2 17.00 KM 1.00
HEAD LEAD FOR FINE SAND 0.2 0.50 KM 1.00

C) LABOUR:-

ADD 10 % C.P. & 5 % O.H.C. ON Rs. 501.91

4148.00 each ###
###
###
414.80
TOTAL ### 1)

75.00 Rmt 112.50 2)

L.S. Job 450.00 3)

L.S. Job 30.00 4)

L.S. Job 150.00 5)

(1 To 5) ###

###

G.Total ###

Cost for 1No. A ###

Say Rs. ###

 EXECUTIVE ENGINEER,
I&PH DIVISION,GHUMARWIN.

f Leader make 125 mm having

Rate Unit Amount

### each ###

### % ###

### % ###

###

LS 500.00

Total ### 1)
 59.00 KG ###

462.37

Total ### 2)

1.50 Cm ### 3)

40.00 each 800.00 4)

118.68 MT 23.25

162.22 MT 31.78

TOTAL 55.03 5)

0.681 QTL. 680.57

156.27/10 Nos 156.27

 TOTAL 836.84 6)

TOTAL ###

###

###

G.TOTAL ###

Cost per valve ###

Say Rs ###

EXECUTIVE ENGINEER,

I & P H DIV. GHUMARWIN.

Rate Unit Amount

75.83 each 630.91

75.83 each 21.23
Total 652.14
 9.78
Total 661.92
99.29
TOTAL 761.21

OST PER CUM = 76.12

SAY Rs 76.10 (a)

2100.00 P/day 94.50

45.00 Kg 28.35
200.00 / 100 6.00
20.00 P.Coil 5.00
75.83 each 10.24
75.83 each 6.82
75.83 each 1213.3

TOTAL ###
204.63
TOTAL ###

COST PER CU 156.88 (b)

verage rate for P.J.W. 116.50

0% each (a+b)/2
SAY Rs 116.50

EXECUTIVE ENGINEER,

I & P H DIV. GHUMARWIN.

 50 mm dia.
RATE UNIT AMOUNT

75.83 each 30.33

121.33 each 23.05

TOTAL 53.38

+ 8.01

TOTAL 61.39

Cost per Rmt 6.14

SAY 6.10

E
N IN FOUNDATION &
ATER CLOSING IN FOUNDATION)
(200 CUSECS)
( 14 CUM OF SATURATED SOIL)
OR 12 HOURS
Rate Unit Amount

26.84 26.84 966.24

90.00 90 45.00
 300.00 300 600.00
TOTAL ###

121.33 121.3 182.00

TOTAL 182.00

TOTAL ###
268.99
G. TOTAL ###
OST FOR 14 CUM ###
OST PER ONE CUM 147.30
SAY 147.30

###
###
TOTAL ### PER CUM

EXECUTIVE ENGINEER,
I & P H DIV. HAMIRPUR.

S. TUBE (LIGHT

TRENCHES

GMS TUBES 65 mm dia

QTY. RATE UNITAMOUNT

0.79 75.83 each 59.91

0.30 ### each 36.40

 LS 6.50

TOTAL ###

0.0628 198.2 MT 12.46

0.0628 86.42 MT 5.43

TOTAL 17.89

G.TOTAL ###

LL AMOUNT

120.69 18.10

G.TOTAL ###

Cost per Rmt 13.88

SAY 13.90

EXECUTIVE ENGINEER,

I &P H DIV. GHUMARWIN.

FITTERELDAR FOR W/LEAD & HEMP OIL

0.10 0.19 .41-1.79
0.14 0.30 .22-2.79
0.19 0.40 .61-4.35
0.30 0.79 .13-6.93
0.40 1.19 (L)7.69
 0.54 1.79 -(M)9.5
0.73 2.69 -M)11.2

LIGHT CLASS) INCLUDING

ED & PAID FOR SEPARATLY
GMS TUBES 100 mm dia

QUANTITYRATE UNITAMOUNT

1.19 75.83 each 90.24

0.40 ### each 48.53
LS 6.50
TOTAL ###

10.20 ### 00 RMT 51.82

10.20 ### 00 RMT 23.84
TOTAL 75.65
G.TOTAL ###

N ALL AMOUNT
220.92 33.14
G.TOTAL ###

Cost per Rmt 25.41

SAY 25.40

EXECUTIVE ENGINEER,
I &P H DIV. GHUMARWIN.

FOR B/STONE 50 376

D FOR B/STONE 50 127.9
D FOR BAJRI 20 T 347.6
D FOR BAJRI 20 TO 118.3
D FOR BAJRI 6 TO 347.6
D FOR BAJRI 6 TO 118.3
D FOR COURSED S347.6
D FOR COURSED S 118.3
D FOR FINE SAND 0200.3
D FOR FINE SAND 0118.3

Y GRADED,

CHARGE
RATE UNIT AMOUNT

232.80 CUM 232.80

TOTAL 232.80 1)

376.04 CUM 376.04

127.92 CUM 127.92
TOTAL 503.96 2)
LS 52.42
TOTAL 52.42 3)
G.TOTAL 789.18
0.00
G.TOTAL 789.18
SAY Rs. 789.00

288.60 CUM 288.60

 TOTAL 288.60 1)

347.63 CUM 347.63

118.34 CUM 118.34
TOTAL 465.97 2)
LS 52.42
TOTAL 52.42 3)
G.TOTAL 806.99
0.00
G.TOTAL 806.99
SAY Rs. 807.00

343.80 CUM 343.80

TOTAL 343.80 1)

347.63 CUM 347.63

118.34 CUM 118.34
TOTAL 465.97 2)
LS 52.42
TOTAL 52.42 3)
G.TOTAL 862.19
0.00
G.TOTAL 862.19
SAY Rs. 862.00

132.00 CUM 132.00

TOTAL 132.00 1)

347.63 CUM 347.63

118.34 CUM 118.34
TOTAL 465.97 2)
LS 39.31
TOTAL 39.31 3)
G.TOTAL 637.28
 95.59
G.TOTAL 732.87
SAY Rs. 733.00

144.00 CUM 144.00

TOTAL 144.00 1)

200.26 CUM 200.26

118.34 CUM 118.34
TOTAL 318.60 2)
LS 39.31
TOTAL 39.31 3)
G.TOTAL 501.91
75.29
G.TOTAL 577.20
SAY Rs. 577.00

EXECUTIVE ENGINEER,
I & P H DIVISION, GHUMARWIN.
 ANALYSIS OF RATES.
Drilling as per specification laid down in IS-2800-1991 percussion Rig/ combination drilling Rig starting with 650mm diametres M.S.
pipe reduced to 450/400mm dia pipe confirming to IS-specification No.4270-1992 in all kind of soil i/c cost of all consumable store
fuel and lubricats etc complete in all respect within all lead and lift i/c transporation errection and levelling of rig at site i/c electricity
and water charges.
SNo. DESCRIPTION Unit. Qty. Rate Amount.
1 Drilling from 0 to 30 metres below ground level approximate
working hours @5hrs per mtr = 125 hrs from nominal starata with Rig @ Rs. 1030.00
per hours per metres (out turn rate attached).
Cost of 30 metres. P/Hour. 150.00 1030.00 154500.00
Cost of 1 metre. 5150.00
Say Rs. 5150.00 only.

2 Drilling from 30 to 60 metres below ground level approximate

working hours @5.5hrs per mtr = 165 hrs from nominal starata with Rig @ Rs. 1030.00
per hours per metres.
Cost of 30 metres. P/Hour. 165.00 1030.00 169950.00
Cost of 1 metre. 5665.00
Say Rs. 5665.00 only.

3 Drilling from 60 to 90 metres below ground level approximate

working hours @6.0hrs per mtr = 180 hrs from nominal starata with Rig @ Rs. 1030.00
per hours per metres.
Cost of 30 metres. P/Hour. 180.00 1030.00 185400.00
Cost of 1 metre. 6180.00
Say Rs. 6180.00 only.

4 Drilling from 90 to 140 metres below ground level approximate

working hours @6.3hrs per mtr = 325hrs from nominal starata with Rig @ Rs. 1030.00

per hours per metres.

Cost of 50 metres. P/Hour. 325.00 1030.00 334750.00
Cost of 1 metre. 6695.00
Say Rs. 6695.00 only.

5 Drilling from 140 to 190 metres below ground level approximate

working hours @6.3hrs per mtr = 350hrs from nominal starata with Rig @ Rs. 1030.00

per hours per metres.

Cost of 50 metres. P/Hour. 350.00 1030.00 360500.00
Cost of 1 metre. 7210.00
Say Rs. 7210.00 only.

6 Drilling from 190 to 240 metres below ground level approximate

working hours @6.3hrs per mtr = 375hrs from nominal starata with Rig @ Rs. 1030.00

per hours per metres.

Cost of 50 metres. P/Hour. 375.00 1030.00 386250.00
Cost of 1 metre. 7725.00
Say Rs. 7725.00 only.

7 Drilling from 240 to 290 metres below ground level approximate

working hours @7.9hrs per mtr = 395hrs from nominal starata with Rig @ Rs. 1030.00

per hours per metres.

Cost of 50 metres. P/Hour. 395.00 1030.00 406850.00
Cost of 1 metre. 8137.00
Say Rs. 8137.00 only.

8 Drilling from 290 to 340 metres below ground level approximate

working hours @8.3hrs per mtr = 475hrs from nominal starata with Rig @ Rs. 1030.00

per hours per metres.

Cost of 50 metres. P/Hour. 415.00 1030.00 427450.00
Cost of 1 metre. 8549.00
Say Rs. 8549.00 only.
Executive Engineer
Jal Shakti Division 1 Una
 ANALYSIS OF RATE
Pdg and Lowering of site Electric Resistance welded (ERW) stainless steel cage type "V" wire
wound screens size of 300 mm dia. 8 mm thick with slot opening as per IS 8110-2000 i.e
lowering in the bore hole in vertical position i/c cost of all scafolding .

Rate of 300mm dia 8mm thick (as per RC No. 4-Ind/SP-3-M-11(03) 24542.00
29/08 (29) dt 25.10.08 valid up to 30/7/09.
24542.00

Fabrication of assembly such as cutting threading and packer seal etc. LS 125.00

Lowering of slotted pipe 1/4 hours mtrs depth @ Rs. 1030/ hours. 1030.00 0.25 257.50

2% for wastage. 24542.00 2% 490.84

Carriage of pipe. 25.00 KM 56.86
Total:- 25472.20
5 %over head charge on Rs. 24542.00 5% 1227.10
26699.30
Add 12% GST on Rs. 25472.20 3056.66
Add 1% LC on Rs. 26699.30 266.99
30022.96

Say Rs. 30022.95

ANALYSIS OF RATE
Pdg. and 'Lowering of site Electric Resistance welded (ERW) stainless steel cage type "V"
wire wound screens size of 200 mm dia.6.4 mm thick with slot opening as per IS 8110-2000
i.e lowering in the bore hole in vertical position i/c cost of all scafolding .

Rate of 200mm dia 6.4mm thick (as per RC No. 4-Ind/SP-3-M-11(03) 11722.00
29/08 (29) dt 25.10.08 valid up to 30/7/09.
11722.00

Fabrication of assembly such as cutting threading and packer seal etc. LS 100.00

Lowering of slotted pipe 1/4 hours mtrs depth @ Rs. 1030/ hours. 1030.00 0.25 257.50

2% for wastage. 11722.00 2% 234.44

Carriage of pipe. 25.00 KM 32.22
Total:- 12346.16
5 %over head charge on Rs. 11722.00 5% 586.10
12932.26
Add 12% GST on Rs. 12346.16 1481.54
Add 1% LC on Rs. 12932.26 129.32
14543.12

Say Rs. 14543.10

Executive Engineer,
Jal Shakti Division 1 Una

ANALYSIS OF RATE

Providing and lowering of ERW/EAW 300 mm nominal size bevelled edge M.S pipes 8mm thick
conforming to ISI specification No.4270/1992 in random length to 4 to 7 mtrs.
Unit 1 Rmt.
Description of item Qty Rate Unit Amount

Rate of 300 mm dia M.S. pipe 3240.63

 3240.63

Febrication charges of assembly such as cutting threading welding and packer L.S. 125.00
seat etc.

Lowering of pipe 1/4 hours mtrs depth @ Rs. 1030/ hours. 1030.00 0.25 257.50

Carriage of pipe from Amb store to site of work. 49.68

Total 3672.81

Add 10% CP and 5% Over Head Charges except cost of pipe on Rs. 432.18 64.83

Add 5% Over Head Charges on cost of pipe on Rs. 3240.63 162.03

3899.67
Add 12% GST 3672.81 440.74
Add 1% LC 3672.81 36.73
Total:- 4377.13
Say Rs. 4377.15

Rate of supplying and lowering of 3oomm dia 8.0mm thick M.S. pipe. 4377.15

Add 30% convertion of Blind Pipe into Slotted pipe Total:- 1313.15
5690.30
Say Rs. 5674.40

Executive Engineer,
Jal Shakti Division Amb

ANALYSIS OF RATE

Providing and lowering of ERW/EAW 175 mm nominal size bevelled edge M.S pipes 6.4mm
thick conforming to ISI specification No.4270/1992 in random length to 4 to 7 mtrs.

Unit 1 Rmt.

Rate of 175 mm dia M.S. pipe ( As per price list of Gaurang Products Pvt Ltd) 1507.40

1507.40

Febrication charges of assembly such as cutting threading welding and packer L.S. 100.00
seat etc.

Lowering of pipe 1/4 hours mtrs depth @ Rs. 1030/ hours. 1030.00 0.25 257.50

Carriage of pipe from Amb store to site of work. 28.15

Total 1893.05

Add 10% CP and 5% Over Head Charges except cost of pipe on Rs. 385.65 57.85

Add 5% Over Head Charges on cost of pipe on Rs. 1507.40 75.37

 2026.27
Add 12% GST 1893.05 227.17
Add 1% LC 1893.05 18.93
Total:- 2272.37
Say Rs. 2272.35

Rate of supplying and lowering of 175mm dia 6.4mm thick M.S. pipe. 2272.35

Add 30% convertion of Blind Pipe into Slotted pipe Total:- 681.70
2954.06
Say Rs. 2954.05

Executive Engineer,
Jal Shakti Division Amb
Division Amb
Division Amb
 ASSEMBLY CHART
Name of Work: Providing CAD for LIS Dulehar (T/well No.112) and LIS Pubowal in Teh. Haroli
Distt. Una(HP). (SH: System deficiency correction by drilling and developing of 1 No. T/well in
place of defunct T/well Pubowal (T/well Aujle).

200 mtrs deep T/well.

NOT TO SCALE

40.00 Mtr

4.00 Mtr

18.00 Mtr

V-wire 1.00 Mtr

30.00 Mtr

5.00

10.00 Mtr

34.00 Mtr

200 Mtr 7.00 Mtr

5.00 Mtr

V-wire 1.00 Mtr

10.00 Mtr

8.00 Mtr

20.00 Mtr

5.00 Mtr
 2.00 Mtr

300 MM Dia M.S. Slotted Pipe 9 Mtr

300 MM Dia V-wire 1 Mtr
300 MM Dia MSERW pipe 98 Mtr
200 MM Dia M.S. Slotted Pipe 20 Mtr
200 MM Dia V-wire 1 Mtr
200 MM Dia MSERW pipe 71 Mtr Executive Engineer,
200 Mtr JAL SHAKTI Division No.1 Una

Ans. 140 125 100 150 110 300

300 MS pipe 50.00 45.00 40.00 40.00 50.00 50.00 62.00
300 MM V wire 5.00 5.00 5.00 5.00 5.00 5.00 1.00
300 MS pipe 10.00 10.00 15.00 10.00 10.00 10.00 28.00
200 MS pipe 20.00 20.00 20.00 10.00 20.00 10.00 20.00
200 MM V wire 7.50 7.50 5.00 3.00 7.50 3.00 7.50
200 MS pipe 20.00 20.00 15.00 10.00 20.00 10.00 20.00
200 MM V wire 7.50 7.50 5.00 2.00 7.50 2.00 7.50
200 MS pipe 23.50 18.50 13.50 13.50 23.50 13.50 23.50
200 MM V wire 5.00 5.00 5.00 5.00 5.00 5.00 5.00
200 MS pipe 1.50 1.50 1.50 1.50 1.50 1.50 1.50

150.00 140.00 125.00 100.00 150.00 110.00

 BASIC RATE OF MATERIAL
Name of Work: Providing CAD for LIS Dulehar (T/well No.112) and LIS Pubowal in Teh. Haroli
Distt. Una(HP). (SH: System deficiency correction by drilling and developing of 1 No. T/well in
place of defunct T/well Pubowal (T/well Aujle).

1 Transportation of Rig. Rs. 30000.00 Job

2 Sample box Rs. 1000.00 Each

3 M.S. Taper Reducer Rs. 2000.00 Each

4 Centrelized guids. Rs. 320.00 Each

5 Bail plug Rs. 2000.00 Each

6 Iron cap looking arrangement Rs. 1500.00 Each

7 S/packing of gravel Rs. 450.00 Mtrs

8 Dev. of T/well bu back washing Rs. 1500.00 Per Hour up to 150m

method with Air compression. Rs. 2500.00 Per Hr above to 150m

9 Dev.of T/well & establishment of Rs. 1292.00 Per Hour up to 150m

discharge with high capacity V.T/ Rs. 2000.00 Per Hr above to 150m
submerssible pump

10 Extraction :
in contact with soil Rs. 375.00 Mtrs
Freely hanging Rs. 187.50 Mtrs

11 Testing of verticalitily Rs. 5000.00 Job

12 Dismentalling Rs. 5000.00 Job

13 C/O Barbed wire fencing Rs. 4000.00 Each job

14 Handing over of T/well. Rs. 1000.00 Each

It is cetified that these rates are prevailing lowest market rates.

Assistant Engineer Executive Engineer,

J.S. sub Division Tahliwal JAL SHAKTI Division 1 Una
 LEAD CHART.

Name of work :- Providing LWSSto PC/NC Hab (Cap-2003) to Vill Talwal in Tehsil Amb & Di
0
(Sub Head :- Drilling, lowering of assembly & Development of Tube well

Carriage of V- wire wound screen from Nangal R/ Station

Carriage of ERW pipe of 300 mm dia & 200 mm dia

Nangal R/ Station By Mechanical Transport

Average 52.00
K.M.

Certified that the lead has been taken in the lead chart is
Per Hour up to 150m shortest, economical and feasible route.
Per Hr above to 150m Sd/-
Assistant Engineer,
Per Hour up to 150m IPH Sub Dvision No.2 Una
Per Hr above to 150m
300mm dia Unit: 100 mt. 200mm dia
BY M/T BY M/T
Cost upto Ist 5 km. 1259.90 Cost upto Ist 5 km.
5 10 5 104.27 521.35 5 10
10 20 10 87.8 878.00 10 20
20 52 32 74.9 2396.80 20 52

Cost for 100 mtr 5056.05 Cost for 100 mtr

Cost for 1 mt. 50.56 Cost for 1 mt.

KTI Division 1 Una

LEAD CHART.
Name of work :- Providing LWSSto PC/NC Hab (Cap-2003) to Vill Talwal in Tehsil Amb & Di
0
(Sub Head :- Drilling, lowering of assembly & Development of Tube well

Carriage of ERW pipe of 300 mm dia & 200 mm dia

Nangal R/ Station By Mechanical Transport

Average 52.00
K.M.
Certified that the lead has been taken in the lead chart is
shortest, economical and feasible route.
Sd/-
Assistant Engineer,
IPH Sub Dvision No.2 Una

300mm dia Unit: 100 mt. 200mm dia

BY M/T BY M/T
Cost upto Ist 5 km. 1259.90 Cost upto Ist 5 km.
5 10 5 104.27 521.35 5 10
10 20 10 87.8 878.00 10 20
20 52 32 74.9 2396.80 20 52

Cost for 100 mtr 5056.05 Cost for 100 mtr

Cost for 1 mt. 50.56 Cost for 1 mt.

 ANALYSIS OF RATE

Item:-Drilling as per specification laid down is IS 2800-1964 with percus

Vill Talwal in Tehsil Amb & Distt Una (HP). or compination rig starting with 650 mm dia pipe and reducing 450/400
MS pipe ' (conforming to ISI specification No. 4270-1992 )in all kind of s
lopment of Tube well 100 Mtr. Deep. the cost of all consumable stores POL etc. complete in all respect in all

lead and lift i/c ttransportation erection and levelling of Rig at stite i/c
electricity and water charge etc. 0-5 m. mannual

i) Drilling from 5.00 mtrs. to 30.00 mtrs below ground level approximate
working hours 100 from nominal strata with 941.28
Site of work per hours (out turn rate of Rig. for 2006-07 0f T/well Gagret.)

Cost for 25 mtr 100 941.28 94128

Cost per mt 25 3765.12
Say Rs.
ii) Drilling from 30.00 mtrs. to 60.00 mtrs below ground level approximate
working hours 160 from nominal strata with 941.28
per hours (out turn rate of Rig. for 2006-07 0f T/well Gagret.)

Cost for 30 mtr 160 941.28 ###

Dvision No.2 Una Cost per mt 30 5020.16
Say Rs.
Unit: 100 mt. iii) Drilling from 60.00 mtrs. to 100 mtrs below ground level approximate
working hours 270 from nominal strata with 941.28
713.49 per hours (out turn rate of Rig. for 2006-07 0f T/well Gagret.)
5 59.08 295.40
10 49.75 497.50 Cost for 40 mtr 270 941.28 ###
32 42.44 1358.08 Cost per mt 40 6353.64
Say Rs.
iv) Drilling from 100. mtrs. to 150.00 mtrs below ground level approximate
2864.47 working hours 340 from nominal strata with 941.28
per hours (out turn rate of Rig. for 2006-07 0f T/well Gagret.)

28.64 Cost for 50 mtr 340 941.28 ###

Cost per mt 50 6400.7
Say Rs.

Executive Engineer,
IPH Division No II Una.
Executive Engineer,
I&PH Divn.No.II,Una.
Vill Talwal in Tehsil Amb & Distt Una (HP).

lopment of Tube well 100 Mtr. Deep. Analysis of rate

S/Lowering of ERW/EAW stainless steel cage type 'V' wire wound screens
of size 300mm, 8mm thick with slot opening 1.00mm as per IS 8110-2000 i.e

lowering in the bore hole in vertical position i/c cost of all scafolding.
1. Rate of 300 mm dia MS pipe ( As per rate contract No.4- IND/SP-3 (M-II(0
29/08(29) opened on 25.10.2008 and valid upto 30.07.2009.
ii)Add 4 % Vat.

Site of work iii) Fabrication of assembly such as cutting threading and welding etc.

iv) Lowering of slotted pipe 1/4 hours mrs. D 941.28

2% wastage for cutting ,threading of pipe according to the design of assemb
25523.68
Carriage average lead. 52 KM

Dvision No.2 Una

Unit: 100 mt. Add 5% over head charges except carriage 26419.47

713.49
5 59.08 295.40 Say Rs.
10 49.75 497.50
32 42.44 1358.08 S/Lowering of ERW/EAW stainless steel cage type 'V' wire wound screens of
size 200mm 6.40 mm thick with slot opening 1.00mm as per IS -8110-2000 i
lowering in the bore hole in vertical position i/c cost of all scafolding.
2864.47
1. Rate of 300 mm dia MS pipe ( As per rate contract No.4- IND/SP-3 (M-II(0
29/08(29) opened on 25.10.2008 and valid upto 30.07.2009.
28.64
ii)Add 4 % Vat.

Executive Engineer, iii) Fabrication of assembly such as cutting threading and welding etc.
IPH Division No II Una.
iv) Lowering of slotted pipe 1/4 hours mrs. D 941.28
2% wastage for cutting ,threading of pipe according to the design of assemb
12190.88
Carriage average lead. 52 KM

Add 5% over head charges except carriage 12745.02

Say Rs.

ANALYSIS OF RATE
Febrication and lowering of ERW/EAW 300 mm nominal screwed and
 socketed M.S pipes 8mm thick conforming to ISI specification No.
4270/1992 in random length to 4 to 7 mtrs. without any circumfrential joint in
bore hole in vertical position i/c cost of scafolding derricks and embeded in
foundation etc. complete in all respect to the entire satisfaction of the Engine
Charge i/c cost of cutting threading and welding of pipe where required on so
i) Febrication charges of assembly such as cutting threading welding and pac
seat etc.
ii) Handing joint coupling and lowering of MS. pipe in the bore hole 1/4 hours
mtrs. depth @ Rs. 941.28 only per hour (out turn rate of
Rig for the year 2006-07 i.e. Rs. 941.28
iii) 2 % wastage for cutting threading of pipe according t

Add 5% over head charges except carriage 291.70

Providing ERW/EAW 300 mm nominal size screwed and

socketed M.S pipes 8mm thick conforming to ISI specification No.
4270/1992 in random length to 4 to 7 mtrs.

1. Rate as per price list Attached.

Cost of pipe of 300 mm dia 8.00 62.50 Kg per Mtr.

Carriage from Dehli to Nangal Rai 0.625 407.5

Cost per Mtr. 62.5 Kg

Carriage from Railway station Nangal 52.00 Km.

Freight unloading/stacking at site.

Add 5% over head charges except carriage 2919.10

Total Rs.
Say Rs.

Executive Engineer
'IPH Div. No.II Un

ANALYSIS OF RATE

Providing ERW/EAW 200 mm nominal size screwed and

socketed M.S pipes 6.4 mm thick conforming to ISI specification No.
4270/1992 in random length to 4 to 7 mtrs.

1. As per supply order

Cost of pipe of 200 mm dia 6.40 33.57 Kg per Mtr.

Carriage from Dehli to Nangal Rai 0.3357 407.5

Carriage from Railway station Nangal 52 Km.

Freight unloading/stacking at site.

Add 5% over head charges except carriage 1751.00

Febrication and lowering of ERW/EAW 200 mm nominal screwed and

4270/1992 in random length to 4 to 7 mtrs. without any circumfrential joint in
bore hole in vertical position i/c cost of scafolding derricks and embeded in
foundation etc. complete in all respect to the entire satisfaction of the Engine
Charge i/c cost of cutting threading and welding of pipe where required on so
i) Febrication charges of assembly such as cutting threading welding and pac
seat etc.
ii) Handing joint coupling and lowering of MS. pipe in the bore hole 1/4 hours
mtrs. dept 941.28 only per hour (out turn rate of
Rig for the year 2006-07 i.e. Rs. 941.28
iii) 2 % wastage for cutting threading of pipe according to the

Add 5% over head charges except carriage 272.91

Say Rs.

Executive Engineer
'IPH Div. No.1I Un
 Analysis of rate
own is IS 2800-1964 with percussion Lowering of ERW/EAW stainless steel cage type 'V' wire wound screens of size 300mm,
m dia pipe and reducing 450/400 mm dia 8mm thick with slot opening 1.00mm as per IS 8110-2000 i.e. lowering in the bore hole in
n No. 4270-1992 )in all kind of soil i/c vertical position i/c cost of all scafolding.
etc. complete in all respect in all

and levelling of Rig at stite i/c

Fabrication of assembly such as cutting threading and w 150

ow ground level approximate
only. Lowering of slotted pipe 1/4 hou 941.28 0.25 235.32
0f T/well Gagret.)
Carriage Average lead 52.00 KM 50.56

3765.10 only. 435.88

elow ground level approximate
only.
0f T/well Gagret.) 435.88
Say Rs. 435.88 only.

Lowering of ERW/EAW stainless steel cage type 'V' wire wound screens of
5020.16 only. size 200mm 6.40 mm thick with slot opening 1.00mm as per IS -8110-2000 i.e.
ow ground level approximate lowering in the bore hole in vertical position i/c cost of all scafolding.
only.
0f T/well Gagret.)

Fabrication of assembly such as cutting threading and we 75.00

6353.60 only. Lowering of slotted pipe 1/4 hou 941.28 0.25 235.32
elow ground level approximate
only.
0f T/well Gagret.) Carriage Average lead 52 KM 28.64

338.96

6400.70 only.

338.96
Executive Engineer, Say Rs. 338.96 only.
I&PH Divn.No.II,Una.

Executive Engineer,

I&PH Divn.No.II,Una.
age type 'V' wire wound screens
ng 1.00mm as per IS 8110-2000 i.e.

n i/c cost of all scafolding.

ate contract No.4- IND/SP-3 (M-II(03)
upto 30.07.2009. 24542 Analysis of rate
981.68 Lowering of ERW/EAW stainless steel cage type 'V' wire wound screens of size 300mm,
8mm thick with slot opening 1.00mm as per IS 8110-2000 i.e. lowering in the bore hole in
25523.68 vertical position i/c cost of all scafolding.
threading and welding etc. 150.00
Welding of V-wire with MS pipe 3.14*32.31*2*2.00 405.81
Per hours 235.32
according to the design of assembly. Fabrication of assembly such as cutting threading and we 150.00
0.02 510.47
50.56 iv) Lowering of slotted pipe 1/4 hours mrs. D 941.28 235.32
Per hours.
26470.03 Carriage Average lead 52 KM 50.56

1320.97
841.69
27791.00 Add 5% over head charges except carriage 791.13 39.56
27791.00 only.
881.25
age type 'V' wire wound screens of Say Rs. 881.25 only
ng 1.00mm as per IS -8110-2000 i.e.
n i/c cost of all scafolding. Lowering of ERW/EAW stainless steel cage type 'V' wire wound screens of
size 200mm 6.40 mm thick with slot opening 1.00mm as per IS -8110-2000 i.e.
ate contract No.4- IND/SP-3 (M-II(03) lowering in the bore hole in vertical position i/c cost of all scafolding.
upto 30.07.2009. 11722.00
Welding of V-wire with MS pipe 3.14*21.91*2*2.00 275.19
468.88
12190.88 Fabrication of assembly such as cutting threading and we 100.00

threading and welding etc. iv) Lowering of slotted pipe 1/4 hours mrs. D 941.28 235.32
75.00 Per hours.
Per hours 235.32
according to the design of assembly. Carriage Average lead #REF! KM #REF!
0.02 243.82
28.64 #REF!
12773.66
Add 5% over head charges. #REF! #REF!

637.25
#REF!
13410.91 Say Rs. #REF! only.
13410.90 only.

Executive Engineer,
I&PH Divn.No.II,Una.
Executive Engineer,
I&PH Divn.No.II,Una.

ANALYSIS OF RATE

0 mm nominal screwed and Febrication and lowering of ERW/EAW 300 mm nominal screwed and
 to ISI specification No. socketed M.S pipes 8mm thick conforming to ISI specification No.
without any circumfrential joint into the 4270/1992 in random length to 4 to 7 mtrs. without any circumfrential joint into the
folding derricks and embeded in bore hole in vertical position i/c cost of scafolding derricks and embeded in
he entire satisfaction of the Engineer-in- foundation etc. complete in all respect to the entire satisfaction of the Engineer-in-
lding of pipe where required on socket. Charge i/c cost of cutting threading and welding of pipe where required on socket.
cutting threading welding and packer i) Febrication charges of assembly such as cutting threading welding and packer
150.00 I seat etc. 150.00
MS. pipe in the bore hole 1/4 hours per ii) Handing joint coupling and lowering of MS. pipe in the bore hole 1/4 hours per
mtrs. depth @ Rs. 941.28 only per hour (out turn rate of Rig for the
235.32 ii year 2006-07 941.28 235.32
2819.10 56.38 iii Carriage from Railway station Nangal 52.00 Km. 50.56

441.70 435.88
14.59

456.28 i 435.88
Say Rs. 435.88 only.

e screwed and Executive Engineer,

to ISI specification No. 'IPH Div. No.1I Una.

Rate /KG 45.11 ANALYSIS OF RATE

Febrication and lowering of ERW/EAW 200 mm nominal screwed and

socketted MS pipe 6.4 mm thick confirming to ISI specification No
45.11 4270/1992 in random length to 4 to 7 mtrs. without any circumfrential joint into the
Kg per Mtr. 2819.10 bore hole in vertical position i/c cost of scafolding derricks and embeded in
Tonne 254.69 foundation etc. complete in all respect to the entire satisfaction of the Engineer-in-
Charge i/c cost of cutting threading and welding of pipe where required on socket.
i) Febrication charges of assembly such as cutting threading welding and packer
45.11 2819.10 seat etc. 75.00
ii) Handing joint coupling and lowering of MS. pipe in the bore hole 1/4 hours per
50.56 mtrs. dept 941.28 only per hour (out turn rate of Rig for the
year 2006-07 941.28 235.32
100.00
2969.66 Carriage from Nangal Railway to site 52.00 Km. 28.64
310.32
145.96
2969.66 ii
310.32
(i+ii) 3425.94 Say Rs. 310.32 only.
3425.90 only.

Executive Engineer, Executive Engineer,

'IPH Div. No.II Una. IPH Div. No.1I Una.

e screwed and
ng to ISI specification No.

Rate /KG 45.11

45.11
Kg per Mtr. 1514.20
 136.80

28.64

100.00
1779.64

87.55
1879.64

0 mm nominal screwed and

without any circumfrential joint into the
folding derricks and embeded in
he entire satisfaction of the Engineer-in-
lding of pipe where required on socket.
cutting threading welding and packer
75.00
MS. pipe in the bore hole 1/4 hours per

235.32
1879.64 37.59

347.91

13.65

361.56
Total:- 2241.19
2241.19 only.

Executive Engineer,
'IPH Div. No.1I Una.
 INPUT DATA FOR TUBE WELL.

Name of work :- Providing LWSSto PC/NC Hab (Cap-2003) to Vill Talwal in Tehsil Amb & Distt Una (HP).
screens of size 300mm,
wering in the bore hole in
(Sub Head :- Drilling, lowering of assembly & Development of Tube 100 Mtr

1 Total depth recommended as per Senier Hydrogeolog 100 Mtr. &

Vide his letter No as attached with the estimate. Rate of K 39.53
Excise du 4.07
2 Rate of ERW M.S.pipe 300 mm dia 8 mm thinkness 43.60
having outer dia 323.9 mm at Divisional store. Add 3% CST. 1.31
Add 0.5% Insp Charge. 0.20
3 Rate of ERW M.S.pipe 200 mm dia 6.4 mm thinkness Copy attached. 45.11 / Kg.
having outer dia 323.9 mm at Divisional store.

4 Rate of ERW Stainless Steel Cage type "V" wire wou 24542.00 Per mtr.
screen of size 300 mm, 8 mm with slot opening 1.0 mm.

5 Rate of ERW Stainless Steel Cage type "V" wire wou 11722.00 Per mtr.
screen of size 200 mm, 6.3 mm with slot opening 1.0 mm.

6 Out turn rate of rig for the year 2006-07 of Rs. 941.28 Copy attached.

7 Fabrication of assembly such as cutting threading and welding etc.

For 300 mm dia. LS rate R 150.00
For 200 mm dia. LS rate R 75.00

8 Carriage of ERW pipe & V wire wound screen pipeNangal

f R/ Station 52.00 K.M.

Executive Engineer
I&PH Division No. II Una

V wire wound screen pipe from Railway station Nagal

Carriage of ERW pipe from Divisional store Brnoh
screens of size 300mm,
wering in the bore hole in

8110-2000 i.e.
ntial joint into the

the Engineer-in-
quired on socket.
ing and packer

e 1/4 hours per

ntial joint into the

the Engineer-in-
quired on socket.
ing and packer

e 1/4 hours per

 GENERAL ABSTRACT O
Name of work :- Providing LWSSto PC/NC Hab (Cap-2003) to Vill Talw
0
(Sub Head :- Drilling, lowering of assembly & Development o
0

0
S.No.
Sub head and item of work.
1 2
1 Cost for Drilling, lowering of assembly & Development of 1 NoTube we
Dilwan 145 mtrs deep & T/Well at Churru 125 mtrs deep.
2 Cost for Drilling, lowering of assembly & Development of 1 NoTube w
Takarla (New Abadi) 125 mtrs deep

24542 May be corrected Say Rs.

ERAL ABSTRACT OF COST
Hab (Cap-2003) to Vill Talwal in Tehsil Amb & Distt Una (HP).
(C/O 3 Nos T/Wells.)
assembly & Development of Tube well

Amount
3
& Development of 1 NoTube well at ###
125 mtrs deep. (As per Annexure "A)
& Development of 1 NoTube well at ###
(As per Annexure "B)

Total ###

49,75,000/-Only

Executive Engineer
I&PH Division no. II Una
 ABSTRACT OF COST
NAME OF WORK:-C/O separate LWSS to village Saloi & Pramb , Bharobar, Behli in Tehsil Amb Distt. Una (HP).
#REF!
S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1 2 3 4 5 6
1 Transportation of Rig along with allied accessories etc. complete including 1 Job. 30000.00 each 30000.00
errection and levelling at site, through all kinds of roads, approaches fields
etc. in all leads and lifts completed in all respects as per the directions of
Engineer - in-Charge.

2 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with

upto-date amnedments,if any,with Direct Rotary Rig drilling
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia
M.S pipe confirming to IS 4270-2001 with up-to-date amendements,if any,
in all kind of soils,boulders,rocks,collapsible strata,sturated soils,artesian
conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions
of the Engineer -in -Charge.
i) Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
0-30 mtrs below ground level within all leads and lifts. 30 mtrs. 5150.00 mtr. 154500.00

ii) Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
30-60 mtrs below ground level within all leads and lifts. 30 mtrs. 5460.00 mtr. 163800.00

iii) 'Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
60- 90 mtrs below ground level within all leads and lifts. 30 mtrs. 6180.00 mtr. 185400.00

iv) 'Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
90-150 mtrs below ground level within all leads and lifts. 60 mtrs. 6490.00 mtr. 389400.00
 3 Collection ,preservaion and display of suitable size sample box with top lid 1 No. 1000.00 each 1000.00
and locking arrangement till handing over of the tube well to the department
complete in all respects as per direction of the Engineer -in-Charge.

4(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 60 mtrs. 3692.95 mtr. 221577.00
Socketed M.S.pipe 300 mm dia nominal size housing, 8 mm thick having out side
dia mtrs.323.9 mm (Screwed End Socketted), confirming to I.S 4270-2001 with
up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without
any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and
lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 5 mtrs. 4800.85 mtr. 24004.00
Socketed M.S.slotted pipe (1020 slots per mtrs) 300 mm dia nominal size housing,
8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), confirming to
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded
without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete
in all respects as per the directions of the Engineer -in-Charge.

5 Providing and fixing M.S taper/reducer as per lengths approved by 1 No. 2000.00 each 2000.00
Engineer -in-Charge ,the material of M.S taper/reducer shall be equivalent
to parent pipe material and shall conform to chemical composition as per
clasue 5.2 and mechanical properties as per clasue 6.1and table 1 of IS
4270-2001 with upto date amendments,if any, complete in all respect as
per directions of the Engineer -in -Charge.
6(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 65 mtrs. 1991.90 mtr. 129474.00
Socketed M.S.pipe 200 mm dia nominal size housing, 6.4 mm thick having out side
dia mtrs. 219.10 mm (Screwed End Socketted), confirming to I.S 4270-2001 with
up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without
any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and
lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 20 mtrs. 2589.45 mtr. 51789.00
Socketed M.S.slotted pipe (1020 slots per mtrs) 200 mm dia nominal size housing,
6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), confirming to
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded
without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete
in all respects as per the directions of the Engineer -in-Charge.

7 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well 5 Nos. 800.00 each. 4000.00
as per IS 226-1991 with up-to-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions
of the Engineer -in-Charge.

8 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 1 No. 2000.00 each. 2000.00
200 mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up -to
date amendements ,ifany, within all leads and lifts, complete in all respects
per directions of the Engineer -in- Charge.

9 Pdg. and fixing in position threaded iron cap with locking arrangements of 1 No. 1500.00 each. 1500.00
approved design to prevent foreign matter from getting into bore hole,as
required, within all leads and lifts, complete in all respects as per directions
of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable 150 mtrs. 450.00 mtr. 67500.00
material with an average specific gravity of not less than 2.5,not containing
more than 2% by weight of thin flat of elangated pieces, shall be of sub
rounded to rounded grains with minimum angular features of size 2-3.35 mm ,
shall be free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt
loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of
shroud around screen generally 100 mm to the entire depth of the bore as
per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads
and lifts complete in all respects as per direction of the Engineer -in- Charge.

11 Development of tubewell by back washing method,with air compressor of 30 Hours. 1500.00 Hour. 45000.00
minimum 750 CFM capacity, pumping pipe of 200 mm size and air line of
minimum 65 mm size or with other suitable method,till the well is thoroughly
developed as per clause 4.2 of IS 11189-1985, with upto date anebdnebts,if
any, complete in all respects as per direction of the Engnieer -in- Charge.

12 Development of tubewell by continous over pumping method,with VT pump/ 20 Hours. 1292.00 Hour. 25840.00
submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is
sand free as per IS-11189-1985 up -to- date amendments, if any, complete
in all respects as per directions of the Engineer -in- Charge .The draw down
and discharge to be established by running the VT/ Submersible pump contin
-uosuly for 8 hours in the presence of officer not less than the rank of Assistant
Engineer.

13 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1 Job 5000.00 Job 5000.00
1979 with upto date amendments, if any, using plumb or plunger 6 mm smaller
in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II)
1979 with up-to-date amendments, if any, as appended with the tender
documents and handed over complete in all respect as the directions of the
Engineer -in- Charge.
14 Dismentalling of Rig or other allied accesssories after completion of job within 1 No. 4000.00 Each. 4000.00
all leads and lifts, complete in all respects as per the directions of the Engineer
-in- Charge.

15 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe 1 No. 4000.00 Each. 4000.00
gaurd the bore of tubewell with angle iron of size 40x40x6 mm 1.5 mtrs in
height, ambedded in concrete block of 30x30x30 cm in all leads and lifts,
complete in all respects as per the directions of the Engineer -in- Charge.

16 Handing over of the tubewell in complete shape as per appendex "B" of 1 Job. 1000.00 Each 1000.00
clause 7 of IS 2800 (Part-II) -1979 with upto date amendmentes if any, as
appended with the tender documents, in laminated form , in triplicate,
complete in all respect as per the directions of the Engineer-in-Charge. 1512784.00

Say Rs. 15,12,785/- only.

Executive Engineer
IPH Division No.II Una.
 ABSTRACT OF COST
NAME OF WORK:-Aug. of LWSS Chintpurni (SH: Drilling lowering assembly and development of T/well 80 mtrs 200mm)
0
S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1 2 3 4 5 6
1 Transportation of Rig along with allied accessories etc. complete including 1 Job. 15000.00 each 15000.00
errection and levelling at site, through all kinds of roads, approaches fields
etc. in all leads and lifts completed in all respects as per the directions of
Engineer - in-Charge.

2 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with

upto-date amnedments,if any,with Direct Rotary Rig drilling
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia
M.S pipe confirming to IS 4270-2001 with up-to-date amendements,if any,
in all kind of soils,boulders,rocks,collapsible strata,sturated soils,artesian
conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions
of the Engineer -in -Charge.
i) Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
0-30 mtrs below ground level within all leads and lifts. 30 mtrs. 5150.00 mtr. 154500.00

ii) Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
30-60 mtrs below ground level within all leads and lifts. 30 mtrs. 5460.00 mtr. 163800.00

iii) 'Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
60- 90 mtrs below ground level within all leads and lifts. 20 mtrs. 6180.00 mtr. 123600.00

3 Collection ,preservaion and display of suitable size sample box with top lid 1 No. 700.00 each 700.00
and locking arrangement till handing over of the tube well to the department
complete in all respects as per direction of the Engineer -in-Charge.
4(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 65 mtrs. 1991.90 mtr. 129474.00
Socketed M.S.pipe 200 mm dia nominal size housing, 6.4 mm thick having out side
dia mtrs. 219.10 mm (Screwed End Socketted), confirming to I.S 4270-2001 with
up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without
any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and
lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 15 mtrs. 2589.45 mtr. 38842.00
Socketed M.S.slotted pipe (1020 slots per mtrs) 200 mm dia nominal size housing,
6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), confirming to
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded
without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete
in all respects as per the directions of the Engineer -in-Charge.

5 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well 3 Nos. 800.00 each. 2400.00
as per IS 226-1991 with up-to-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions
of the Engineer -in-Charge.

6 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 1 No. 2000.00 each. 2000.00
200 mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up -to
date amendements ,ifany, within all leads and lifts, complete in all respects
per directions of the Engineer -in- Charge.

7 Pdg. and fixing in position threaded iron cap with locking arrangements of 1 No. 1500.00 each. 1500.00
approved design to prevent foreign matter from getting into bore hole,as
required, within all leads and lifts, complete in all respects as per directions
of the Engineer -in- Charge.
8 Supplying and packing of gravel, consisting of hard quartz or other suitable 90 mtrs. 450.00 mtr. 40500.00
material with an average specific gravity of not less than 2.5,not containing
more than 2% by weight of thin flat of elangated pieces, shall be of sub
rounded to rounded grains with minimum angular features of size 2-3.35 mm ,
shall be free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt
loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of
shroud around screen generally 100 mm to the entire depth of the bore as
per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads
and lifts complete in all respects as per direction of the Engineer -in- Charge.

9 Development of tubewell by back washing method,with air compressor of 20 Hours. 1500.00 Hour. 30000.00
minimum 750 CFM capacity, pumping pipe of 200 mm size and air line of
minimum 65 mm size or with other suitable method,till the well is thoroughly
developed as per clause 4.2 of IS 11189-1985, with upto date anebdnebts,if
any, complete in all respects as per direction of the Engnieer -in- Charge.

10 Development of tubewell by continous over pumping method,with VT pump/ 15 Hours. 1292.00 Hour. 19380.00
submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is
sand free as per IS-11189-1985 up -to- date amendments, if any, complete
in all respects as per directions of the Engineer -in- Charge .The draw down
and discharge to be established by running the VT/ Submersible pump contin
-uosuly for 8 hours in the presence of officer not less than the rank of Assistant
Engineer.
721696.00

Say Rs.7,21,700/- only.

Executive Engineer
IPH Division No.II Una.
 ABSTRACT OF COST
NAME OF WORK:-IMPROVEMENT OF LWSS BADOLI TIURI - 2ND IN TEHSIL AMB DISTT. UNA (HP)
(SH: Drilling lowering assembly and development of T/well 150 mtrs deep).
S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1 2 3 4 5 6
1 Transportation of Rig along with allied accessories etc. complete including 1 Job. 30000.00 each 30000.00
errection and levelling at site, through all kinds of roads, approaches fields
etc. in all leads and lifts completed in all respects as per the directions of
Engineer - in-Charge.

2 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with

upto-date amnedments,if any,with Direct Rotary Rig drilling
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia
M.S pipe confirming to IS 4270-2001 with up-to-date amendements,if any,
in all kind of soils,boulders,rocks,collapsible strata,sturated soils,artesian
conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions
of the Engineer -in -Charge.
i) Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
0-30 mtrs below ground level within all leads and lifts. 30 mtrs. 5150.00 mtr. 154500.00

ii) Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
30-60 mtrs below ground level within all leads and lifts. 30 mtrs. 5460.00 mtr. 163800.00

iii) 'Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
60- 90 mtrs below ground level within all leads and lifts. 30 mtrs. 6180.00 mtr. 185400.00

iv) 'Drilling and lowering of M.S. Casing pipe confirming to IS 4270-2001 with
up-to-date amendments,if any, of suitable sizes as mentioned above,from
90-150 mtrs below ground level within all leads and lifts. 60 mtrs. 6490.00 mtr. 389400.00
 3 Collection ,preservaion and display of suitable size sample box with top lid 1 No. 1000.00 each 1000.00
and locking arrangement till handing over of the tube well to the department
complete in all respects as per direction of the Engineer -in-Charge.

4(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 60 mtrs. 3690.45 mtr. 221427.00
Socketed M.S.pipe 300 mm dia nominal size housing, 8 mm thick having out side
dia mtrs.323.9 mm (Screwed End Socketted), confirming to I.S 4270-2001 with
up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without
any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and
lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 5 mtrs. 4797.60 mtr. 23988.00
Socketed M.S.slotted pipe (1020 slots per mtrs) 300 mm dia nominal size housing,
8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), confirming to
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded
without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete
in all respects as per the directions of the Engineer -in-Charge.

5 Providing and fixing M.S taper/reducer as per lengths approved by 1 No. 2000.00 each 2000.00
Engineer -in-Charge ,the material of M.S taper/reducer shall be equivalent
to parent pipe material and shall conform to chemical composition as per
clasue 5.2 and mechanical properties as per clasue 6.1and table 1 of IS
4270-2001 with upto date amendments,if any, complete in all respect as
per directions of the Engineer -in -Charge.
6(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 65 mtrs. 1991.00 mtr. 129415.00
Socketed M.S.pipe 200 mm dia nominal size housing, 6.4 mm thick having out side
dia mtrs. 219.10 mm (Screwed End Socketted), confirming to I.S 4270-2001 with
up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without
any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and
lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End 20 mtrs. 2588.30 mtr. 51766.00
Socketed M.S.slotted pipe (1020 slots per mtrs) 200 mm dia nominal size housing,
6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), confirming to
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded
without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete
in all respects as per the directions of the Engineer -in-Charge.

7 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well 5 Nos. 800.00 each. 4000.00
as per IS 226-1991 with up-to-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions
of the Engineer -in-Charge.

8 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 1 No. 2000.00 each. 2000.00
200 mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up -to
date amendements ,ifany, within all leads and lifts, complete in all respects
per directions of the Engineer -in- Charge.

9 Pdg. and fixing in position threaded iron cap with locking arrangements of 1 No. 1500.00 each. 1500.00
approved design to prevent foreign matter from getting into bore hole,as
required, within all leads and lifts, complete in all respects as per directions
of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable 150 mtrs. 450.00 mtr. 67500.00
material with an average specific gravity of not less than 2.5,not containing
more than 2% by weight of thin flat of elangated pieces, shall be of sub
rounded to rounded grains with minimum angular features of size 2-3.35 mm ,
shall be free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt
loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of
shroud around screen generally 100 mm to the entire depth of the bore as
per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads
and lifts complete in all respects as per direction of the Engineer -in- Charge.

11 Development of tubewell by back washing method,with air compressor of 30 Hours. 1500.00 Hour. 45000.00
minimum 750 CFM capacity, pumping pipe of 200 mm size and air line of
minimum 65 mm size or with other suitable method,till the well is thoroughly
developed as per clause 4.2 of IS 11189-1985, with upto date anebdnebts,if
any, complete in all respects as per direction of the Engnieer -in- Charge.

12 Development of tubewell by continous over pumping method,with VT pump/ 20 Hours. 1292.00 Hour. 25840.00
submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is
sand free as per IS-11189-1985 up -to- date amendments, if any, complete
in all respects as per directions of the Engineer -in- Charge .The draw down
and discharge to be established by running the VT/ Submersible pump contin
-uosuly for 8 hours in the presence of officer not less than the rank of Assistant
Engineer.

13 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1 Job 5000.00 Job 5000.00
1979 with upto date amendments, if any, using plumb or plunger 6 mm smaller
in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II)
1979 with up-to-date amendments, if any, as appended with the tender
documents and handed over complete in all respect as the directions of the
Engineer -in- Charge.
14 Dismentalling of Rig or other allied accesssories after completion of job within 1 No. 4000.00 Each. 4000.00
all leads and lifts, complete in all respects as per the directions of the Engineer
-in- Charge.

15 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe 1 No. 4000.00 Each. 4000.00
gaurd the bore of tubewell with angle iron of size 40x40x6 mm 1.5 mtrs in
height, ambedded in concrete block of 30x30x30 cm in all leads and lifts,
complete in all respects as per the directions of the Engineer -in- Charge.

16 Handing over of the tubewell in complete shape as per appendex "B" of 1 Job. 1000.00 Each 1000.00
clause 7 of IS 2800 (Part-II) -1979 with upto date amendmentes if any, as
appended with the tender documents, in laminated form , in triplicate,
complete in all respect as per the directions of the Engineer-in-Charge. 1512536.00

Say Rs. 15,12,535/- only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-C/O separate LWSS to village Saloi & Pramb , Bharobar, Behli in Tehsil Amb Distt. Una (HP).(SH: Drilling Estimated Cost:- 702514.00 only
lowering assembly and development of T/well 150 mtrs deep near truck union Amb for LWSS Saloi and Pramb). Earnest Money :- 14050.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 2 3 4 5 6 7
1 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, 1 Job. 22500.00 Rs. Twenty two each 22500.00
through all kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, thousand five hundred
approaches fields etc. in all leads and lifts completed in all respects as per the directions of Engineer - in- only.
Charge.

2 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with
Direct Rotary Rig drilling starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils,boulders,rocks,collapsible
strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants and
other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 1600.00 Rs. One thousand six mtr. 48000.00
suitable sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts. hundred only.
(HPSR 1993)
ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 2000.00 Rs. Two thousand only. mtr. 60000.00
suitable sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts. (HPSR 1993)

iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 2400.00 Rs. Two thousand four mtr. 72000.00
suitable sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts. (HPSR 1993) hundred only.

iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 2800.00 Rs. Two thousand mtr. 84000.00
suitable sizes as mentioned above,from 90-150 mtrs below ground level within all leads and lifts. (HPSR 1993) eight hundred only.

3 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing 1 No. 750.00 Rs. Seven hundred each 750.00
over of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge. Fifty only.

4(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 300 mm dia 60 mtrs. 2769.70 Rs. Two thousand mtr. 166182.00
nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to seven hundred sixty
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any nine and ps. Seventy
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps only.
embedded in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads
and lifts, complete in all respects as per the directions of the Engineer -in-Charge.
(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 300 5 mtrs. 3600.65 Rs. Three thousand six mtr. 18003.00
mm dia (1020 slots per mtrs) nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed hundred and ps. sixty
End Socketted), conforming to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in five only.
length, welded without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and
welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.

5 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 1500.00 Rs. One thousand five each 1500.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per hundred only.
clasue 5.2 and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -Charge.

6(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 200 mm dia 65 mtrs. 1493.95 Rs. One thousand four mtr. 97107.00
nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming hundred ninety three
to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any and ps. ninety five
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps only.
embedded in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads
and lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 200 20 mtrs. 1942.10 Rs. One thousand nine mtr. 38842.00
mm dia (942 slots per mtrs) nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed hundred fourty two
End Socketted), conforming to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in and ps. ten only.
length, welded without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and
welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.

7 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Rs. Three hundred each. 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the (HPSR 1993) twenty only.
directions of the Engineer -in-Charge.

8 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 800.00 Rs. Eight hundred each. 800.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all (HPSR 1993) only.
respects per directions of the Engineer -in- Charge.

9 Pdg. and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 600.00 Rs.Six hundred only. each. 600.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per (HPSR 1993)
directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific 150 mtrs. 180.00 Rs. One hundred mtr. 27000.00
gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of (HPSR 1993) eighty only.
sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities
such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with
upto date amendments, if any, around intake of tubewell with minium thickness of shroud around screen
generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any,
with in all leads and lifts complete in all respects as per direction of the Engineer -in- Charge.

11 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, 30 Hours. 1125.00 Rs.one thousand one Hour. 33750.00
pumping pipe of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is hundred twenty five
thoroughly developed as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all only.
respects as per direction of the Engnieer -in- Charge.

12 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable 20 Hours. 969.00 Rs. Nine hundred sxty Hour. 19380.00
capacity not less than double the discharge established by the compressor method/ design discharge, untill the nne ony.
well is sand free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per
directions of the Engineer -in- Charge .The draw down and discharge to be established by running the VT/
Submersible pump continuosuly for 8 hours in the presence of officer not less than the rank of Assistant
Engineer.

13 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if 1 Job 3750.00 Rs.Three thousand Job 3750.00
any, using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of seven hundred fifty
the verticality test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to- only.
date amendments, if any, as appended with the tender documents and handed over complete in all respect as
the directions of the Engineer -in- Charge.

14 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 No. 3000.00 Rs.Three thousand Each. 3000.00
respects as per the directions of the Engineer -in- Charge. only.
15 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe gaurd the bore of tubewell with 1 No. 3000.00 Rs.Three thousand Each. 3000.00
angle iron of size 40x40x6 mm 1.5 mtrs in height, ambedded in concrete block of 30x30x30 cm in all leads and only.
lifts,complete in all respects as per the directions of the Engineer -in- Charge.

16 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with 1 Job. 750.00 Rs.Seven hundred fifty Each 750.00
upto date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, only.
complete in all respect as per the directions of the Engineer-in-Charge.

702514.00
Rs. Seven lac two thousand five hundred fourteen only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-Imp of LWSS Dharamsala Mahantan, Behar Bhatehar and Ghangret in Tehsil Amb Distt. Una (HP).(SH: Estimated Cost:- 473192.00 only
Drilling , Lowering and development of 7" bore (Mini T/Well) in a depth of 90 mtrs.in village Dharamsala Mahantan) Earnest Money :- 9464.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 2 3 4 5 6 7
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with 1 Job. 2475.00 Rs. two thousand four each 2475.00
necessary accessories etc to the site of work & erection of rig including leveling etc complete in all respects as hundred seventy five
per directions of Engineer-in-Charges. only.

2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary 90 mtrs. 3375.00 Rs. three thousand Mtr 303750.00
method required for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc three hundred seventy
including cost of attachments , extractable casing,consumable stores, bits, water, POL etc. in annular space five only.
etc.complete in all respects as per direction of the Engineer-in-Charge.

3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of 1 No. 22.50 Rs. Twenty Two and Each 23.00
Engineer-in-Charges ps. fifty only.
4 Development of bore well and yield testing with air compressor through V-notch and disifection etc. as per IS 1 No. 1762.50 Rs. One thousand Each 1763.00
2800-1979 complete in all respect as per direction of the Engineer-in-Charge. seven hundred sixty
two and ps. fifty only.

5 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and 90 mtrs. 1341.75 Rs. One thousand Mtr 120758.00
requirement of rotary attachment from approved manufacturers complete in all respect as per direction of the three hundred forty
Engineer-in-Charge. one and ps. Seventy
five only.

6 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding 15 Hrs 975.00 Rs. nine hundred Hr 14625.00
transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as seventy five only.
per direction of Engineer-in-Charges.

7 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch 10 Hrs 900.00 Rs. nine hundred only. Hr 9000.00
as per IS 2800-1979 inclluding transportation of equpment etc, to the site of work complete in all respect for
the bore drilled by RC rig, as per direction of Engineer-in-Charges.

8 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia 10 mtrs. 330.00 Rs.Three hundred Mtr 3300.00
slotted pipe as per IS as per 4270-2001 with upto date ammendments welded and joints into bore hole in thirty only.
vertical position i/c cost of all cutting, threading and welding of pipe etc within all leads and lifts complete in all
respects per directions of the Engineer -in- Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 622.50 Rs.six hundred twenty Each. 623.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all two and ps. fifty only.
respects per directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an 90 mtrs. 187.50 Rs. one hundred Each. 16875.00
average specific gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated eighty seven and ps.
pieces, shall be of sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be fifty only.
free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe
IS 4097-1967 with upto date amendments, if any, around intake of tubewell with minium thickness of shroud
around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in-
Charge.

473192.00
Rs. four lac seventy three thousand one hundred ninety
two only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-Pdg LWSS Bhaira Diara in Tehsil Amb Distt. Una (HP).(SH: Drilling , Lowering and development of 7" bore Estimated Cost:- 473192.00 only
(Mini T/Well) in a depth of 90 mtrs.) Earnest Money :- 9464.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 2 3 4 5 6 7
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with 1 Job. 2475.00 Rs. two thousand four each 2475.00
necessary accessories etc to the site of work & erection of rig including leveling etc complete in all respects as hundred seventy five
per directions of Engineer-in-Charges. only.

2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary 90 mtrs. 3375.00 Rs. three thousand Mtr 303750.00
method required for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc three hundred seventy
including cost of attachments , extractable casing,consumable stores, bits, water, POL etc. in annular space five only.
etc.complete in all respects as per direction of the Engineer-in-Charge.

3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of 1 No. 22.50 Rs. Twenty Two and Each 23.00
Engineer-in-Charges ps. fifty only.
4 Development of bore well and yield testing with air compressor through V-notch and disifection etc. as per IS 1 No. 1762.50 Rs. One thousand Each 1763.00
2800-1979 complete in all respect as per direction of the Engineer-in-Charge. seven hundred sixty
two and ps. fifty only.

5 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and 90 mtrs. 1341.75 Rs. One thousand Mtr 120758.00
requirement of rotary attachment from approved manufacturers complete in all respect as per direction of the three hundred forty
Engineer-in-Charge. one and ps. Seventy
five only.

6 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding 15 Hrs 975.00 Rs. nine hundred Hr 14625.00
transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as seventy five only.
per direction of Engineer-in-Charges.

7 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch 10 Hrs 900.00 Rs. nine hundred only. Hr 9000.00
as per IS 2800-1979 inclluding transportation of equpment etc, to the site of work complete in all respect for
the bore drilled by RC rig, as per direction of Engineer-in-Charges.

8 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia 10 mtrs. 330.00 Rs.Three hundred Mtr 3300.00
slotted pipe as per IS as per 4270-2001 with upto date ammendments welded and joints into bore hole in thirty only.
vertical position i/c cost of all cutting, threading and welding of pipe etc within all leads and lifts complete in all
respects per directions of the Engineer -in- Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 622.50 Rs.six hundred twenty Each. 623.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all two and ps. fifty only.
respects per directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an 90 mtrs. 187.50 Rs. one hundred Each. 16875.00
average specific gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated eighty seven and ps.
pieces, shall be of sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be fifty only.
free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe
IS 4097-1967 with upto date amendments, if any, around intake of tubewell with minium thickness of shroud
around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in-
Charge.

473192.00
Rs. four lac seventy three thousand one hundred ninety
two only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-Improvement of LWSS Kinoo Aloh Suhin, Sidh Chalet and Badoli Tiuri Phase-Ist in tehsil Amb Distt. Una Estimated Cost:- 424149.00 only
(HP)(SH: Drilling , Lowering and development of 7" bore (Mini T/Well) in a depth of 80 mtrs.in village Kinoo ) Earnest Money :- 8483.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 2 3 4 5 6 7
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with 1 Job. 2475.00 Rs. two thousand four each 2475.00
necessary accessories etc to the site of work & erection of rig including leveling etc complete in all respects as hundred seventy five
per directions of Engineer-in-Charges. only.

2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary 80 mtrs. 3375.00 Rs. three thousand Mtr 270000.00
method required for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc three hundred seventy
including cost of attachments , extractable casing,consumable stores, bits, water, POL etc. in annular space five only.
etc.complete in all respects as per direction of the Engineer-in-Charge.

3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of 1 No. 22.50 Rs. Twenty Two and Each 23.00
Engineer-in-Charges ps. fifty only.
4 Development of bore well and yield testing with air compressor through V-notch and disifection etc. as per IS 1 No. 1762.50 Rs. One thousand Each 1763.00
2800-1979 complete in all respect as per direction of the Engineer-in-Charge. seven hundred sixty
two and ps. fifty only.

5 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and 80 mtrs. 1341.75 Rs. One thousand Mtr 107340.00
requirement of rotary attachment from approved manufacturers complete in all respect as per direction of the three hundred forty
Engineer-in-Charge. one and ps. Seventy
five only.

6 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding 15 Hrs 975.00 Rs. nine hundred Hr 14625.00
transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as seventy five only.
per direction of Engineer-in-Charges.

7 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch 10 Hrs 900.00 Rs. nine hundred only. Hr 9000.00
as per IS 2800-1979 inclluding transportation of equpment etc, to the site of work complete in all respect for
the bore drilled by RC rig, as per direction of Engineer-in-Charges.

8 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia 10 mtrs. 330.00 Rs.Three hundred Mtr 3300.00
slotted pipe as per IS as per 4270-2001 with upto date ammendments welded and joints into bore hole in thirty only.
vertical position i/c cost of all cutting, threading and welding of pipe etc within all leads and lifts complete in all
respects per directions of the Engineer -in- Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 622.50 Rs.six hundred twenty Each. 623.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all two and ps. fifty only.
respects per directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an 80 mtrs. 187.50 Rs. one hundred Mtr 15000.00
average specific gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated eighty seven and ps.
pieces, shall be of sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be fifty only.
free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe
IS 4097-1967 with upto date amendments, if any, around intake of tubewell with minium thickness of shroud
around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in-
Charge.

424149.00
Rs. four lac twenty four thousand one hundred fourty
nine only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-Improvement of LWSS Kinoo Aloh Suhin, Sidh Chalet and Badoli Tiuri Phase-Ist in tehsil Amb Distt. Una Estimated Cost:- 473192.00 only
(HP)(SH: Drilling , Lowering and development of 7" bore (Mini T/Well) in a depth of 90 mtrs.in village Sidh Chalet ) Earnest Money :- 9464.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 2 3 4 5 6 7
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with 1 Job. 2475.00 Rs. two thousand four each 2475.00
necessary accessories etc to the site of work & erection of rig including leveling etc complete in all respects as hundred seventy five
per directions of Engineer-in-Charges. only.

2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary 90 mtrs. 3375.00 Rs. three thousand Mtr 303750.00
method required for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc three hundred seventy
including cost of attachments , extractable casing,consumable stores, bits, water, POL etc. in annular space five only.
etc.complete in all respects as per direction of the Engineer-in-Charge.

3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of 1 No. 22.50 Rs. Twenty Two and Each 23.00
Engineer-in-Charges ps. fifty only.
4 Development of bore well and yield testing with air compressor through V-notch and disifection etc. as per IS 1 No. 1762.50 Rs. One thousand Each 1763.00
2800-1979 complete in all respect as per direction of the Engineer-in-Charge. seven hundred sixty
two and ps. fifty only.

5 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and 90 mtrs. 1341.75 Rs. One thousand Mtr 120758.00
requirement of rotary attachment from approved manufacturers complete in all respect as per direction of the three hundred forty
Engineer-in-Charge. one and ps. Seventy
five only.

6 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding 15 Hrs 975.00 Rs. nine hundred Hr 14625.00
transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as seventy five only.
per direction of Engineer-in-Charges.

7 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch 10 Hrs 900.00 Rs. nine hundred only. Hr 9000.00
as per IS 2800-1979 inclluding transportation of equpment etc, to the site of work complete in all respect for
the bore drilled by RC rig, as per direction of Engineer-in-Charges.

8 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia 10 mtrs. 330.00 Rs.Three hundred Mtr 3300.00
slotted pipe as per IS as per 4270-2001 with upto date ammendments welded and joints into bore hole in thirty only.
vertical position i/c cost of all cutting, threading and welding of pipe etc within all leads and lifts complete in all
respects per directions of the Engineer -in- Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 622.50 Rs.six hundred twenty Each. 623.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all two and ps. fifty only.
respects per directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an 90 mtrs. 187.50 Rs. one hundred Mtr 16875.00
average specific gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated eighty seven and ps.
pieces, shall be of sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be fifty only.
free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe
IS 4097-1967 with upto date amendments, if any, around intake of tubewell with minium thickness of shroud
around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in-
Charge.

473192.00
Rs. four lac seventy three thousand one hundred ninety
two only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-Imp. of LWSS Bhalola Saloori in Tehsil Amb Distt. Una (HP). Estimated Cost:- 735033.00 only
(SH: Drilling lowering assembly and development of T/well 140 mtrs deep). Earnest Money :- 14701.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, 1 Job. 22500.00 Rs. Twenty two each 22500.00
through all kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, thousand five hundred
approaches fields etc. in all leads and lifts completed in all respects as per the directions of Engineer - in- only.
Charge.

2 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with
Direct Rotary Rig drilling starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils,boulders,rocks,collapsible
strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants and
other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 1600.00 Rs. One thousand six mtr. 48000.00
suitable sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts. hundred only.
(HPSR 1993)
ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 2000.00 Rs. Two thousand only. mtr. 60000.00
suitable sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts. (HPSR 1993)

iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 2400.00 Rs. Two thousand four mtr. 72000.00
suitable sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts. (HPSR 1993) hundred only.

iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 50 mtrs. 2800.00 Rs. Two thousand mtr. 140000.00
suitable sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts. (HPSR 1993) eight hundred only.

3 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing 1 No. 750.00 Rs. Seven hundred each 750.00
over of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge. Fifty only.

4(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 300 mm dia 55 mtrs. 2766.10 Rs. Two thousand mtr. 152136.00
nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to seven hundred sixty
I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any six and ps. ten only.
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads
and lifts, complete in all respects as per the directions of the Engineer -in-Charge.
(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 300 5 mtrs. 3595.90 Rs. Three thousand mtr. 17980.00
mm dia (1020 slots per mtrs) nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed five hundred ninety
End Socketted), conforming to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in five and ps. ninety
length, welded without any circumferential joints,into bore hole in vertical position including cost of all only.
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and
welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.

5 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 1500.00 Rs. One thousand five each 1500.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per hundred only.
clasue 5.2 and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -Charge.

6(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 200 mm dia 60 mtrs. 1492.30 Rs. One thousand four mtr. 89538.00
nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming hundred ninety two
to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any and ps. Thirty only.
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads
and lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 200 20 mtrs. 1939.95 Rs. One thousand nine mtr. 38799.00
mm dia (942 slots per mtrs) nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed hundred thirty nine
End Socketted), conforming to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in and ps. Ninety five
length, welded without any circumferential joints,into bore hole in vertical position including cost of all only.
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and
welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.

7 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Rs. Three hundred each. 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the (HPSR 1993) twenty only.
directions of the Engineer -in-Charge.

8 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 800.00 Rs. Eight hundred each. 800.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all (HPSR 1993) only.
respects per directions of the Engineer -in- Charge.

9 Pdg. and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 600.00 Rs.Six hundred only. each. 600.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per (HPSR 1993)
directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific 140 mtrs. 180.00 Rs. One hundred mtr. 25200.00
gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of (HPSR 1993) eighty only.
sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities
such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with
upto date amendments, if any, around intake of tubewell with minium thickness of shroud around screen
generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any,
with in all leads and lifts complete in all respects as per direction of the Engineer -in- Charge.

11 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, 30 Hours. 1125.00 Rs.one thousand one Hour. 33750.00
pumping pipe of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is hundred twenty five
thoroughly developed as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all only.
respects as per direction of the Engnieer -in- Charge.

12 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable 20 Hours. 969.00 Rs. Nine hundred sxty Hour. 19380.00
capacity not less than double the discharge established by the compressor method/ design discharge, untill the nne ony.
well is sand free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per
directions of the Engineer -in- Charge .The draw down and discharge to be established by running the VT/
Submersible pump continuosuly for 8 hours in the presence of officer not less than the rank of Assistant
Engineer.

13 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if 1 Job 3750.00 Rs.Three thousand Job 3750.00
any, using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of seven hundred fifty
the verticality test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to- only.
date amendments, if any, as appended with the tender documents and handed over complete in all respect as
the directions of the Engineer -in- Charge.

14 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 No. 3000.00 Rs.Three thousand Each. 3000.00
respects as per the directions of the Engineer -in- Charge. only.
15 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe gaurd the bore of tubewell with 1 No. 3000.00 Rs.Three thousand Each. 3000.00
angle iron of size 40x40x6 mm 1.5 mtrs in height, ambedded in concrete block of 30x30x30 cm in all leads and only.
lifts,complete in all respects as per the directions of the Engineer -in- Charge.

16 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with 1 Job. 750.00 Rs.Seven hundred fifty Each 750.00
upto date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, only.
complete in all respect as per the directions of the Engineer-in-Charge.

735033.00
Rs. Seven lac thirty five thousand thirty three only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
NAME OF WORK:-IMPROVEMENT OF LWSS BADOLI TIURI - 2ND IN TEHSIL AMB DISTT. UNA (HP) Estimated Cost:- 1184897.00 only
(SH: Drilling, lowering of assembly and development of T/well 140 mtrs deep). Earnest Money :- 23698.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, 1 Job. 22500.00 Rs. Twenty two each 22500.00
through all kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, thousand five hundred
approaches fields etc. in all leads and lifts completed in all respects as per the directions of Engineer - in- only.
Charge.

2 Earth work in foundatrion for digging Tubewell in all kinds of soils including dewatering ,shoring, struting from 2.36 cum 184.45 Rs. One hundred cum 435.00
GL upto 3 mtrs. including disposing excavated soil in all leads and lift complete in all respect as per the eighty four and ps.
directions of Engineer -in-Charge. Forty five only.

3 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with RC
Rig drilling starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe conforming to IS 4270-
2001 with up-to-date amendements,if any, in all kind of soils,boulders,rocks,collapsible strata,sturated
soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants and other accessories
etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 27 mtrs. 3862.50 Rs. three thousand mtr. 104288.00
suitable sizes as mentioned above,from 3-30 mtrs below ground level within all leads and lifts. eight hundred sixty
two and ps. Fifty only.

ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 4095.00 Rs. four thousand mtr. 122850.00
suitable sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts. ninety five only.

iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 mtrs. 4635.00 Rs. four thousand six mtr. 139050.00
suitable sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts. hundred thirty five
only.

iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 60 mtrs. 4867.50 Rs. four thousand mtr. 292050.00
suitable sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts. eight hundred sixty
seven and ps. Fifty
only.

4 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing 1 No. 750.00 Rs. Seven hundred each 750.00
over of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge. Fifty only.
5(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 300 mm dia 60 mtrs. 3230.95 Rs. three thousand mtr. 193857.00
nominal size 8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to I.S 4270- two hundred thirty
2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential and ps. Ninety five
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in only.
foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 300 5 mtrs. 4200.25 Rs. Four thousand two mtr. 21001.00
mm dia (1020 slots per mtrs) nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed hundred and ps.
End Socketted), conforming to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in Twenty five only.
length, welded without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and
welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.

6 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 1500.00 Rs. One thousand five each 1500.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per hundred only.
clasue 5.2 and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -Charge.

7(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 200 mm dia 65 mtrs. 1832.25 Rs. One thousand mtr. 119096.00
nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming eight hundred thirty
to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any two and ps. Twenty
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps five only.
embedded in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads
and lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 200 20 mtrs. 2382.00 Rs. two thousand mtr. 47640.00
mm dia (942 slots per mtrs) nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed three hundred eighty
End Socketted), conforming to I.S 4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in two only.
length, welded without any circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and
welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.

8 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 600.00 Rs. six hundred only. each. 3000.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the
directions of the Engineer -in-Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 1500.00 Rs. One thousand five each. 1500.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all (HPSR 1993) hundred only.
respects per directions of the Engineer -in- Charge.

10 Pdg. and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1125.00 Rs. One thousand one each. 1125.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per hundred twenty five
directions of the Engineer -in- Charge. only.
11 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific 150 mtrs. 337.50 Rs. three hundred mtr. 50625.00
gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of (HPSR 1993) thirty seven and ps.
sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities fifty only.
such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with
upto date amendments, if any, around intake of tubewell with minium thickness of shroud around screen
generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any,
with in all leads and lifts complete in all respects as per direction of the Engineer -in- Charge.

12 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, 30 Hours. 1125.00 Rs.one thousand one Hour. 33750.00
pumping pipe of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is hundred twenty five
thoroughly developed as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all only.
respects as per direction of the Engnieer -in- Charge.

13 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable 20 Hours. 969.00 Rs. Nine hundred sixty Hour. 19380.00
capacity not less than double the discharge established by the compressor method/ design discharge, untill the nine ony.
well is sand free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per
directions of the Engineer -in- Charge .The draw down and discharge to be established by running the VT/
Submersible pump continuosuly for 8 hours in the presence of officer not less than the rank of Assistant
Engineer.

14 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if 1 Job 3750.00 Rs.Three thousand Job 3750.00
any, using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of seven hundred fifty
the verticality test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to- only.
date amendments, if any, as appended with the tender documents and handed over complete in all respect as
the directions of the Engineer -in- Charge.

15 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 No. 3000.00 Rs.Three thousand Each. 3000.00
respects as per the directions of the Engineer -in- Charge. only.
16 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe gaurd the bore of tubewell with 1 No. 3000.00 Rs.Three thousand Each. 3000.00
angle iron of size 40x40x6 mm 1.5 mtrs in height, ambedded in concrete block of 30x30x30 cm in all leads and only.
lifts,complete in all respects as per the directions of the Engineer -in- Charge.

17 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with 1 Job. 750.00 Rs.Seven hundred fifty Each 750.00
upto date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, only.
complete in all respect as per the directions of the Engineer-in-Charge.

1184897.00
Rs. Eleven lac lac eighty four thousand eight hundred
ninety seven only.

Executive Engineer
IPH Division No.II Una.
 DRAFT SCHEDULE OF QUANITY.
Name of work:-Imp. of LWSS Nari Chintpurni and adjoining area of schedule caste basti in Tehsil Amb Distt Una(HP) Estimated Cost:- 477951.00 only
(SH: Drilling , Lowering of assembly and development of Mini T/Well in a depth of 70 mtrs.) Earnest Money :- 9559.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with 1 Job. 30000.00 Rs. Thirty thousand Job. 30000.00
necessary accessories etc to the site of work & erection of rig including leveling etc complete in all respects as only
per directions of Engineer-in-Charges.
2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary 70 mtrs. 3150.00 Rs. Three thousand mtrs. 220500.00
method required for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc including one hundred fifty only
cost of attachments , extractable casing,consumable stores, bits, water, POL etc. in annular space etc.complete
in all respects as per direction of the Engineer-in-Charge.
3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of 1 No. 100.00 Rs. one hundred only Each 100.00
Engineer-in-Charges
4 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and 60 mtrs. 2301.65 Rs. two thousand mtrs. 138099.00
requirement of rotary attachment from approved manufacturers complete in all respect as per direction of the three hundred one and
Engineer-in-Charge. ps sixty five only
5 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding 15 Hrs 1300.00 Rs. one thousand Hrs 19500.00
transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as per three hundred only
direction of Engineer-in-Charges.
6 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch 10 Hrs 1200.00 Rs. one thousand two Hrs 12000.00
as per IS 2800-1979 inclluding transportation of equpment etc, to the site of work complete in all respect for the hundred only
bore drilled by RC rig, as per direction of Engineer-in-Charges.
7 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia slotted 10 mtrs. 2992.15 Rs. two thousand nine mtrs. 29922.00
pipe as per IS as per 4270-2001 with upto date ammendments welded and joints into bore hole in vertical hundred ninety two
position i/c cost of all cutting, threading and welding of pipe etc within all leads and lifts complete in all respects and ps fifteen only
per directions of the Engineer -in- Charge.
8 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" 1 No. 830.00 Rs. eight hundred Each 830.00
hooks as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all thirty only
respects per directions of the Engineer -in- Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an 70 mtrs. 300.00 Rs. three hundred only mtrs. 21000.00
average specific gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated
pieces, shall be of sub rounded to rounded grains with minimum angular features of size 2-3.35 mm , shall be
free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe IS
4097-1967 with upto date amendments, if any, around intake of tubewell with minium thickness of shroud
around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in-
Charge.

11 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 No. 4000.00 Rs. four thousand only Each 4000.00
respects as per the directions of the Engineer -in- Charge.
12 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with 1 Job. 2000.00 Rs. two thousand only Job. 2000.00
upto date amendmentes if any, as appended with the tender documents, in laminated form, in triplicate,
complete in all respect as per the directions of the Engineer-in-Charge.
477951.00
 GENERAL ABSTRACT OF COST

Name of work: Separate water supply schemes for village Dhuge, Loothre, Dittan, Dhilwan, Haleran, Badewal, Bilna and Chandpur n Tehsil Haroli Distt.
Una (HP) (SH: Drilling , lowering of assembly and development of 200mtrs deep T/well at Chandpur and 300mtrs deep at Badewal)

S.No. Sub head and item of work. Amount.

1 Drilling ,Lowering of assembly and development of 1 No. 200 mtrs deep T/well at Chandpur. Annexure "A" 2697559.00

2 Drilling ,Lowering of assembly and development of 1 No. 300 mtrs deep T/well at Badewal. -do- "B" 4106822.00

6804381.00
Say Rs. 66,60,840/- only.

Assistant Engineer Executive Engineer

J.S. sub Division Tahliwal Jalshakti Division 1 Una
 ABSTRACT OF COST
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli consituency in Distt. Una HP (SH: Drilling , lowering of assembly
and development of 125 mtrs deep T/wells at village Lower Khad, Dharampur, Pandoga lower and Badhera)
S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1 2 3 4 5 6
1.00 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all 1 Job. 30000.00 Job 30000.00
kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all
leads and lifts completed in all respects as per the directions of Engineer - in-Charge.
2.00 Earth work in founation for digging of tubewell in all kinds of soils including dewatering, shoring, struting from GL upto 21.21 cum 341.40 cum 7241.00
3 mtrs including disposing excavated soil in all leads and lifts complete in all respect as per direction of the Engineer-
in-charge.

3.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct
Rotary Rig or combination drilling rig,Precussion Rig starting with 650-600 mm dia M.S pipe reduced to 450-400 mm
dia M.S pipe conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils, boulders, rocks,
collapsible strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

3.01 i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 27 Mtrs 5150.00 Mtr 139050.00
suitable sizes as mentioned above,from 3-30 mtrs below ground level within all leads and lifts.
3.02 ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 Mtrs 5665.00 Mtr 169950.00
suitable sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts.
3.03 iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 30 Mtrs 6180.00 Mtr 185400.00
suitable sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts.
3.04 iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of 35 Mtrs 6695.00 Mtr 234325.00
suitable sizes as mentioned above,from 90-125 mtrs below ground level within all leads and lifts.

4.00 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over 1 No. 1000.00 Each 1000.00
of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge.

5.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 mm dia nominal size housing, 8 mm 50 Mtrs 6315.60 Mtr 315780.00
thick having out side dia mtrs.323.9 mm bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position
including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 Mtr 30162.95 Mtr 30163.00
of size 300 mm ,8 mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Chrage.

5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 300 mm dia nominal size housing, 8 4 Mtrs 8210.30 Mtr 32841.00
mm thick having out side dia mtrs.323.9 mm bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation
etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as
per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 2000.00 Each 2000.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2
and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete
in all respect as per directions of the Engineer -in -Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 mm dia nominal size housing, 6.4 58 Mtrs 3601.25 Mtr 208873.00
mm thick having out side dia mtrs.219.10 mm bevelled edge conforming to I.S 4270-2001 with up-todate
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 mtr 14609.35 Mtr 14609.00
of size 200 mm ,6.3mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 mm dia nominal size housing, 6.4 11 Mtrs 4681.65 Mtr 51498.00
mm thick having out side dia mtrs.219.10 mm Screwed End Socketted, conforming to I.S. 4270-2001 slot size
1.57x75mm welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded
in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in
all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Each 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of
the Engineer -in-Charge.

9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks 1 No. 2000.00 Each 2000.00
as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.

10.00 Providing and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1500.00 Each 1500.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of
the Engineer -in- Charge.

11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of 125 Mtrs 450.00 Mtr 56250.00
not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to
the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts
complete in all respects as per direction of the Engineer -in- Charge.

12.00 Extraction of all sizes blind / casing pipe with machine starting from bottom of the bore hole within all leads and lifts
complete in all respects per directions of the Engineer -in- Charge.
12.01 in contact with soil 125 Mtrs 375.00 Mtr 46875.00

12.02 Freely hanging 165 Mtrs 187.50 Mtr 30938.00

13.00 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe 30 Hrs 1500.00 Hr 45000.00
of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed
as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the
Engnieer -in- Charge.

14.00 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity 20 Hrs 1292.00 Hr 25840.00
not less than double the discharge established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer
-in- Charge .The draw down and discharge to be established by running the VT/ Submersible pump continuosuly for 8
hours in the presence of officer not less than the rank of Assistant Engineer.
15.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, 1 Job. 5000.00 Job 5000.00
using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any,
as appended with the tender documents and handed over complete in all respect as the directions of the Engineer -in-
Charge.

16.00 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 Job. 5000.00 Job 5000.00
respects as per the directions of the Engineer -in- Charge.
17.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto 1 Job. 1000.00 Job 1000.00
date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all
respect as per the directions of the Engineer-in-Charge.

Cost of 1 No. Tubewell 1643733.00

Cost of 4 No. Tubewell 6574932.00

Assistant Engineer Executive Engineer

J.S. sub Division Haroli Jalshakti Division 1 Una
 ABSTRACT OF COST
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli consituency in Distt. Una HP (SH: Drilling , lowering of assembly
and development of 150 mtrs deep T/well at village Saloh)

S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1.00 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all 1 Job. 30000.00 Job 30000.00
kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all
leads and lifts completed in all respects as per the directions of Engineer - in-Charge.
2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct
Rotary Rig or combination drilling rig,Precussion Rig starting with 650-600 mm dia M.S pipe reduced to 450-400 mm
dia M.S pipe conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils, boulders, rocks,
collapsible strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5150.00 Mtr 154500.00
sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5665.00 Mtr 169950.00
sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 6180.00 Mtr 185400.00
sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 6695.00 Mtr 334750.00
sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts.

2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 10 Mtrs 7210.00 Mtr 72100.00
sizes as mentioned above,from 140-150 mtrs below ground level within all leads and lifts.

3.00 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over 1 No. 1000.00 Each 1000.00
of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge.

4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 mm dia nominal size housing, 8 mm 60 Mtrs 6315.60 Mtr 378936.00
thick having out side dia mtrs.323.9 mm bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position
including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 Mtr 30162.95 Mtr 30163.00
of size 300 mm ,8 mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Chrage.

5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 300 mm dia nominal size housing, 8 5 Mtrs 8210.30 Mtr 41052.00
mm thick having out side dia mtrs.323.9 mm bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation
etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as
per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 2000.00 Each 2000.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2
and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete
in all respect as per directions of the Engineer -in -Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 mm dia nominal size housing, 6.4 70 Mtrs 3601.25 Mtr 252088.00
mm thick having out side dia mtrs.219.10 mm bevelled edge conforming to I.S 4270-2001 with up-todate
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 mtr 14609.35 Mtr 14609.00
of size 200 mm ,6.3mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Charge.

7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 mm dia nominal size housing, 6.4 13 Mtrs 4681.65 Mtr 60861.00
mm thick having out side dia mtrs.219.10 mm Screwed End Socketted, conforming to I.S. 4270-2001 slot size
1.57x75mm welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded
in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in
all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Each 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of
the Engineer -in-Charge.

9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks 1 No. 2000.00 Each 2000.00
as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.

10.00 Providing and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1500.00 Each 1500.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of
the Engineer -in- Charge.

11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of 150 Mtrs 450.00 Mtr 67500.00
not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to
the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts
complete in all respects as per direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe 30 Hrs 1500.00 Hr 45000.00
of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed
as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the
Engnieer -in- Charge.
13.00 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity 20 Hrs 1292.00 Hr 25840.00
not less than double the discharge established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer
-in- Charge .The draw down and discharge to be established by running the VT/ Submersible pump continuosuly for 8
hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, 1 Job. 5000.00 Job 5000.00
using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any,
as appended with the tender documents and handed over complete in all respect as the directions of the Engineer -in-
Charge.
15.00 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 Job. 5000.00 Job 5000.00
respects as per the directions of the Engineer -in- Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto 1 Job. 1000.00 Job 1000.00
date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all
respect as per the directions of the Engineer-in-Charge.

Cost of 1 No. Tubewell 1881849.00

Assistant Engineer Executive Engineer

J.S. sub Division Haroli Jalshakti Division 1 Una
 ABSTRACT OF COST
NAME OF WORK:-Separate water supply schemes for village Dhuge, Loothre, Dittan, Dhilwan, Haleran, Badewal, Bilna and Chandpur n Tehsil Haroli Distt. Una (HP)
(SH: Drilling , lowering of assembly and development of 200mtrs deep T/well at Chandpur )

S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1.00 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all 1 Job. 30000.00 Job 30000.00
kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all
leads and lifts completed in all respects as per the directions of Engineer - in-Charge.
2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct
Rotary Rig or combination drilling rig,Precussion Rig starting with 650-600 mm dia M.S pipe reduced to 450-400 mm
dia M.S pipe conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils, boulders, rocks,
collapsible strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5150.00 Mtr 154500.00
sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5665.00 Mtr 169950.00
sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 6180.00 Mtr 185400.00
sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 6695.00 Mtr 334750.00
sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts.

2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 7210.00 Mtr 360500.00
sizes as mentioned above,from 140-190 mtrs below ground level within all leads and lifts.

2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 10 Mtrs 7725.00 Mtr 77250.00
sizes as mentioned above,from 190-200 mtrs below ground level within all leads and lifts.

3.00 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over 1 No. 1000.00 Each 1000.00
of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge.

4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 mm dia nominal size housing, 8 mm 98 Mtrs 6800.50 Mtr 666449.00
thick having out side dia mtrs.323.9 mm bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position
including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 Mtr 30162.95 Mtr 30163.00
of size 300 mm ,8 mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Chrage.

5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 300 mm dia nominal size housing, 8 9 Mtrs 8840.65 Mtr 79566.00
mm thick having out side dia mtrs.323.9 mm bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation
etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as
per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 2000.00 Each 2000.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2
and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete
in all respect as per directions of the Engineer -in -Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 mm dia nominal size housing, 6.4 71 Mtrs 3817.75 Mtr 271060.00
mm thick having out side dia mtrs.219.10 mm bevelled edge conforming to I.S 4270-2001 with up-todate
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 mtr 14609.35 Mtr 14609.00
of size 200 mm ,6.3mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Charge.

7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 mm dia nominal size housing, 6.4 20 Mtrs 4963.10 Mtr 99262.00
mm thick having out side dia mtrs.219.10 mm Screwed End Socketted, conforming to I.S. 4270-2001 slot size
1.57x75mm welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded
in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in
all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Each 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of
the Engineer -in-Charge.

9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks 1 No. 2000.00 Each 2000.00
as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.

10.00 Providing and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1500.00 Each 1500.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of
the Engineer -in- Charge.

11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of 200 Mtrs 450.00 Mtr 90000.00
not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to
the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts
complete in all respects as per direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe 30 Hrs 2500.00 Hr 75000.00
of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed
as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the
Engnieer -in- Charge.
13.00 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity 20 Hrs 2000.00 Hr 40000.00
not less than double the discharge established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer
-in- Charge .The draw down and discharge to be established by running the VT/ Submersible pump continuosuly for 8
hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, 1 Job. 5000.00 Job 5000.00
using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any,
as appended with the tender documents and handed over complete in all respect as the directions of the Engineer -in-
Charge.
15.00 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 Job. 5000.00 Job 5000.00
respects as per the directions of the Engineer -in- Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto 1 Job. 1000.00 Job 1000.00
date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all
respect as per the directions of the Engineer-in-Charge.

2697559.00

Assistant Engineer Executive Engineer

J.S. sub Division Tahliwal Jalshakti Division 1 Una
 ABSTRACT OF COST
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli consituency in Distt. Una HP (SH: Drilling , lowering of assembly
and development of 230 mtrs deep T/well at village Ispur)

S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1.00 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all 1 Job. 30000.00 Job 30000.00
kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all
leads and lifts completed in all respects as per the directions of Engineer - in-Charge.
2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct
Rotary Rig or combination drilling rig,Precussion Rig starting with 650-600 mm dia M.S pipe reduced to 450-400 mm
dia M.S pipe conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils, boulders, rocks,
collapsible strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5150.00 Mtr 154500.00
sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5665.00 Mtr 169950.00
sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 6180.00 Mtr 185400.00
sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 6695.00 Mtr 334750.00
sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts.

2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 7210.00 Mtr 360500.00
sizes as mentioned above,from 140-190 mtrs below ground level within all leads and lifts.

2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 40 Mtrs 7725.00 Mtr 309000.00
sizes as mentioned above,from 190-230 mtrs below ground level within all leads and lifts.

3.00 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over 1 No. 1000.00 Each 1000.00
of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge.

4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 mm dia nominal size housing, 8 mm 112 Mtrs 6315.60 Mtr 707347.00
thick having out side dia mtrs.323.9 mm bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position
including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 Mtr 30162.95 Mtr 30163.00
of size 300 mm ,8 mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Chrage.

5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 300 mm dia nominal size housing, 8 11 Mtrs 8210.30 Mtr 90313.00
mm thick having out side dia mtrs.323.9 mm bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation
etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as
per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 2000.00 Each 2000.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2
and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete
in all respect as per directions of the Engineer -in -Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 mm dia nominal size housing, 6.4 85 Mtrs 3601.25 Mtr 306106.00
mm thick having out side dia mtrs.219.10 mm bevelled edge conforming to I.S 4270-2001 with up-todate
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 mtr 14609.35 Mtr 14609.00
of size 200 mm ,6.3mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Charge.

7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 mm dia nominal size housing, 6.4 20 Mtrs 4681.65 Mtr 93633.00
mm thick having out side dia mtrs.219.10 mm Screwed End Socketted, conforming to I.S. 4270-2001 slot size
1.57x75mm welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded
in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in
all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Each 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of
the Engineer -in-Charge.

9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks 1 No. 2000.00 Each 2000.00
as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.

10.00 Providing and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1500.00 Each 1500.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of
the Engineer -in- Charge.

11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of 230 Mtrs 450.00 Mtr 103500.00
not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to
the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts
complete in all respects as per direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe 30 Hrs 2500.00 Hr 75000.00
of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed
as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the
Engnieer -in- Charge.
13.00 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity 20 Hrs 2000.00 Hr 40000.00
not less than double the discharge established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer
-in- Charge .The draw down and discharge to be established by running the VT/ Submersible pump continuosuly for 8
hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, 1 Job. 5000.00 Job 5000.00
using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any,
as appended with the tender documents and handed over complete in all respect as the directions of the Engineer -in-
Charge.
15.00 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 Job. 5000.00 Job 5000.00
respects as per the directions of the Engineer -in- Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto 1 Job. 1000.00 Job 1000.00
date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all
respect as per the directions of the Engineer-in-Charge.

Cost of 1 No. Tubewell 3023871.00

Assistant Engineer Executive Engineer

J.S. sub Division Haroli Jalshakti Division 1 Una
 ABSTRACT OF COST
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli consituency in Distt. Una HP (SH: Drilling , lowering of assembly
and development of 250 mtrs deep T/well at village Rora)

S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1.00 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all 1 Job. 30000.00 Job 30000.00
kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all
leads and lifts completed in all respects as per the directions of Engineer - in-Charge.
2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct
Rotary Rig or combination drilling rig,Precussion Rig starting with 650-600 mm dia M.S pipe reduced to 450-400 mm
dia M.S pipe conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils, boulders, rocks,
collapsible strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5150.00 Mtr 154500.00
sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5665.00 Mtr 169950.00
sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 6180.00 Mtr 185400.00
sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 6695.00 Mtr 334750.00
sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts.

2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 7210.00 Mtr 360500.00
sizes as mentioned above,from 140-190 mtrs below ground level within all leads and lifts.

2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 7725.00 Mtr 386250.00
sizes as mentioned above,from 190-240 mtrs below ground level within all leads and lifts.

2.07 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 10 Mtrs 7725.00 Mtr 77250.00
sizes as mentioned above,from 240-250 mtrs below ground level within all leads and lifts.

3.00 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over 1 No. 1000.00 Each 1000.00
of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge.

4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 mm dia nominal size housing, 8 mm 122 Mtrs 6315.60 Mtr 770503.00
thick having out side dia mtrs.323.9 mm bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position
including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 Mtr 30162.95 Mtr 30163.00
of size 300 mm ,8 mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Chrage.

5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 300 mm dia nominal size housing, 8 12 Mtrs 8210.30 Mtr 98524.00
mm thick having out side dia mtrs.323.9 mm bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation
etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as
per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 2000.00 Each 2000.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2
and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete
in all respect as per directions of the Engineer -in -Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 mm dia nominal size housing, 6.4 92 Mtrs 3601.25 Mtr 331315.00
mm thick having out side dia mtrs.219.10 mm bevelled edge conforming to I.S 4270-2001 with up-todate
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 mtr 14609.35 Mtr 14609.00
of size 200 mm ,6.3mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Charge.

7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 mm dia nominal size housing, 6.4 22 Mtrs 4681.65 Mtr 102996.00
mm thick having out side dia mtrs.219.10 mm Screwed End Socketted, conforming to I.S. 4270-2001 slot size
1.57x75mm welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded
in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in
all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Each 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of
the Engineer -in-Charge.

9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks 1 No. 2000.00 Each 2000.00
as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.

10.00 Providing and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1500.00 Each 1500.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of
the Engineer -in- Charge.

11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of 250 Mtrs 450.00 Mtr 112500.00
not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to
the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts
complete in all respects as per direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe 30 Hrs 2500.00 Hr 75000.00
of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed
as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the
Engnieer -in- Charge.
13.00 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity 20 Hrs 2000.00 Hr 40000.00
not less than double the discharge established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer
-in- Charge .The draw down and discharge to be established by running the VT/ Submersible pump continuosuly for 8
hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, 1 Job. 5000.00 Job 5000.00
using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any,
as appended with the tender documents and handed over complete in all respect as the directions of the Engineer -in-
Charge.
15.00 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 Job. 5000.00 Job 5000.00
respects as per the directions of the Engineer -in- Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto 1 Job. 1000.00 Job 1000.00
date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all
respect as per the directions of the Engineer-in-Charge.

Cost of 1 No. Tubewell 3293310.00

Assistant Engineer Executive Engineer

J.S. sub Division Haroli Jalshakti Division 1 Una
 ABSTRACT OF COST
NAME OF WORK:-Separate water supply schemes for village Dhuge, Loothre, Dittan, Dhilwan, Haleran, Badewal, Bilna and Chandpur n Tehsil Haroli Distt. Una (HP)
(SH: Drilling , lowering of assembly and development of 300mtrs deep at Badewal)

S.No. Sub head and item of work. Qty. Rate Unit. Amount.
1.00 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all 1 Job. 30000.00 Job 30000.00
kinds of roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all
leads and lifts completed in all respects as per the directions of Engineer - in-Charge.
2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct
Rotary Rig or combination drilling rig,Precussion Rig starting with 650-600 mm dia M.S pipe reduced to 450-400 mm
dia M.S pipe conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of soils, boulders, rocks,
collapsible strata,sturated soils,artesian conditions including the cost of all consumable,stores,water,fuel,lubricants
and other accessories etc. complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5150.00 Mtr 154500.00
sizes as mentioned above,from 0-30 mtrs below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 5665.00 Mtr 169950.00
sizes as mentioned above,from 30-60 mtrs below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 30 Mtrs 6180.00 Mtr 185400.00
sizes as mentioned above,from 60-90 mtrs below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 6695.00 Mtr 334750.00
sizes as mentioned above,from 90-140 mtrs below ground level within all leads and lifts.

2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 7210.00 Mtr 360500.00
sizes as mentioned above,from 140-190 mtrs below ground level within all leads and lifts.

2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 7725.00 Mtr 386250.00
sizes as mentioned above,from 190-240 mtrs below ground level within all leads and lifts.

2.07 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 50 Mtrs 8137.00 Mtr 406850.00
sizes as mentioned above,from 240-290 mtrs below ground level within all leads and lifts.

2.07 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable 10 Mtrs 8549.00 Mtr 85490.00
sizes as mentioned above,from 290-300 mtrs below ground level within all leads and lifts.

3.00 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over 1 No. 1000.00 Each 1000.00
of the tube well to the department complete in all respects as per direction of the Engineer -in-Charge.

4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 mm dia nominal size housing, 8 mm 155 Mtrs 6800.50 Mtr 1054078.00
thick having out side dia mtrs.323.9 mm bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position
including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 Mtr 30022.95 Mtr 30023.00
of size 300 mm ,8 mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Chrage.

5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 300 mm dia nominal size housing, 8 11 Mtrs 8840.65 Mtr 97247.00
mm thick having out side dia mtrs.323.9 mm bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation
etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as
per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S 1 No. 2000.00 Each 2000.00
taper/reducer shall be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2
and mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete
in all respect as per directions of the Engineer -in -Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 mm dia nominal size housing, 6.4 110 Mtrs 3817.75 Mtr 419953.00
mm thick having out side dia mtrs.219.10 mm bevelled edge conforming to I.S 4270-2001 with up-todate
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.
7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Cage type "V" wire wound screens 1 mtr 14543.10 Mtr 14543.00
of size 200 mm ,6.3mm thick with slot opening 1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and
material specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in suitable lenghts as per site
conditions, including the cost of SS socket 8 mm thickness of length 140 mm, confirming to AISI grade 304, suitable
to accomodate screen and ring including jointing screen with blind pipes complete in all respects all scaffolding
derricks,poles, clamps, embedding in foundation etc. including cost of all cutting, threading and welding of pipes etc.
within all leads and lifts complete in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping wire having "V" shaped (Wedge)
profile wire with flat surface on the outside and producing expanding slots on the inside of various dimensions,
resistance welded to a cylindrical body made of number of longitudinal special high tensile support rods to provides
smooth unrestricted bore which are in turn welded into cylindrical ring couplings on both sides of screens with in all
leads and lifts complete in all respect as per the direction of the Engineer-in-Charge.

7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 mm dia nominal size housing, 6.4 22 Mtrs 4963.10 Mtr 109188.00
mm thick having out side dia mtrs.219.10 mm Screwed End Socketted, conforming to I.S. 4270-2001 slot size
1.57x75mm welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded
in foundation etc. including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in
all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date 5 Nos. 320.00 Each 1600.00
amendments,if any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of
the Engineer -in-Charge.

9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks 1 No. 2000.00 Each 2000.00
as per IS 2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.

10.00 Providing and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign 1 No. 1500.00 Each 1500.00
matter from getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of
the Engineer -in- Charge.

11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of 300 Mtrs 450.00 Mtr 135000.00
not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and organic material as pe IS 4097-1967 with upto date
amendments, if any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to
the entire depth of the bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts
complete in all respects as per direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe 30 Hrs 2500.00 Hr 75000.00
of 200 mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed
as per clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the
Engnieer -in- Charge.
13.00 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity 20 Hrs 2000.00 Hr 40000.00
not less than double the discharge established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer
-in- Charge .The draw down and discharge to be established by running the VT/ Submersible pump continuosuly for 8
hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, 1 Job. 5000.00 Job 5000.00
using plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality
test shall be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any,
as appended with the tender documents and handed over complete in all respect as the directions of the Engineer -in-
Charge.
15.00 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all 1 Job. 4000.00 Job 4000.00
respects as per the directions of the Engineer -in- Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto 1 Job. 1000.00 Job 1000.00
date amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all
respect as per the directions of the Engineer-in-Charge.

4106822.00

Assistant Engineer Executive Engineer

J.S. sub Division Tahliwal Jalshakti Division 1 Una
 REVISED SCHEDULE OF QUANITY.
NAME OF WORK:-C/O separate LWSS to village Saloi & Pramb , Bharobar, Behli in Tehsil Amb Distt. Una (HP). Tendered Cost:- Rs. 1,263,650.00 only
(SH: Drilling lowering assembly and development of T/well 150 mtrs deep near truck union Amb Estimated Cost:- Rs. 702,514.00 only
for LWSS Saloi and Pramb).
Earnest Money :- Rs. 14,050.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 2 3 4 5 6 7
1 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all kinds of 1 Job. 15000.00 Rs. Fifteen thousand only. each 15000.00
roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all leads and lifts
completed in all respects as per the directions of Engineer - in-Charge.

2 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with Direct Rotary Rig
drilling starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe conforming to IS 4270-2001 with up-to-
date amendements,if any, in all kind of soils,boulders,rocks,collapsible strata,sturated soils,artesian conditions including the
cost of all consumable,stores,water,fuel,lubricants and other accessories etc. complete in all respectsd as per the directions of
the Engineer -in -Charge.

i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 30 mtrs. 3550.00 Rs. Three thousand five mtr. 106500.00
mentioned above,from 0-30 mtrs below ground level within all leads and lifts. hundred fifty only.

ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 30 mtrs. 4000.00 Rs. Four thousand only. mtr. 120000.00
mentioned above,from 30-60 mtrs below ground level within all leads and lifts.

iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 30 mtrs. 5000.00 Rs. Five thousand only. mtr. 150000.00
mentioned above,from 60-90 mtrs below ground level within all leads and lifts.

iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 60 mtrs. 5400.00 Rs. Five thousand four mtr. 324000.00
mentioned above,from 90-150 mtrs below ground level within all leads and lifts. hundred only.

3 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over of the 1 No. 1000.00 Rs. One thousand only. each 1000.00
tube well to the department complete in all respects as per direction of the Engineer -in-Charge.
4(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 300 mm dia nominal size 60 mtrs. 3650.00 Rs. Three thousand six mtr. 219000.00
housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to I.S 4270-2001 with up-todate hundred fifty only.
amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical
position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 300 mm dia (1020 slots 5 mtrs. 3000.00 Rs. Three thousand only. mtr. 15000.00
per mtrs) nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to I.S
4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc.
including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the
directions of the Engineer -in-Charge.
 5 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S taper/reducer shall 1 No. 1500.00 Rs. One thousand five each 1500.00
be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2 and mechanical properties hundred only.
as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete in all respect as per directions of
the Engineer -in -Charge.

6(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 200 mm dia nominal size 65 mtrs. 1950.00 Rs. One thousand nine mtr. 126750.00
housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming to I.S 4270-2001 with up- hundred only.
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 200 mm dia (942 slots 20 mtrs. 2500.00 Rs. Two thousand five mtr. 50000.00
per mtrs) nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming to I.S hundred only.
4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc.
including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the
directions of the Engineer -in-Charge.

7 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date amendments,if 5 Nos. 200.00 Rs. Two hundred only. each. 1000.00
any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of the Engineer -in-Charge.

8 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks as per IS 1 No. 1200.00 Rs. One thousand Two each. 1200.00
2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per directions of the hundred only.
Engineer -in- Charge.

9 Pdg. and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign matter from 1 No. 1200.00 Rs. One thousand Two each. 1200.00
getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of the Engineer -in- hundred only.
Charge.
10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of not less 150 mtrs. 350.00 Rs. Three hundred fifty only. mtr. 52500.00
than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to rounded grains
with minimum angular features of size 2-3.35 mm , shall be free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt
loam,baematte and organic material as pe IS 4097-1967 with upto date amendments, if any, around intake of tubewell with
minium thickness of shroud around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with
upto date amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in- Charge.

11 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe of 200 30 Hours. 1500.00 Rs.one thousand five hundred Hour. 45000.00
mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed as per clause only.
4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the Engnieer -in- Charge.

12 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity not less 20 Hours. 1250.00 Rs.one thousand two hundred Hour. 25000.00
than double the discharge established by the compressor method/ design discharge, untill the well is sand free as per IS- fifty only.
11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer -in- Charge .The draw
down and discharge to be established by running the VT/ Submersible pump continuosuly for 8 hours in the presence of officer
not less than the rank of Assistant Engineer.

13 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, using 1 Job 3000.00 Rs.Three thousand only. Job 3000.00
plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality test shall be
recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any, as appended with
the tender documents and handed over complete in all respect as the directions of the Engineer -in- Charge.

14 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all respects as per 1 No. 3000.00 Rs.Three thousand only. Each. 3000.00
the directions of the Engineer -in- Charge.
15 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe gaurd the bore of tubewell with angle iron of size 1 No. 2000.00 Rs.Two thousand only. Each. 2000.00
40x40x6 mm 1.5 mtrs in height, ambedded in concrete block of 30x30x30 cm in all leads and lifts,complete in all respects as
per the directions of the Engineer -in- Charge.

16 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto date 1 Job. 1000.00 Rs. One thousand only. Each 1000.00
amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.

1263650.00
Rs. Twelve lac sixty three thousand six hundred fifty only.

Executive Engineer
IPH Division No.II Una.
 REVISED SCHEDULE OF QUANITY.
NAME OF WORK:-Imp of LWSS Dharamsala Mahantan, Behar Bhatehar and Ghangret in Tehsil Amb Distt. Una (HP).(SH: Drilling , Tendered Cost:- Rs. 558,160.00 only
Lowering and development of 7" bore (Mini T/Well) in a depth of 90 mtrs.in village Behar Bhatehar) Estimated Cost:- Rs. 473,192.00 only
Earnest Money :- Rs. 9,464.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with necessary 1 Job. 3300.00 Rs. Three thousand three Each 3300.00
accessories etc to the site of work & erection of rig including leveling etc complete in all respects as per directions of Engineer- hundred only.
in-Charges.

2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary method required 90 mtrs. 3800.00 Rs. Three thousand eight Mtr. 342000.00
for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc including cost of attachments , hundred only.
extractable casing,consumable stores, bits, water, POL etc. in annular space etc.complete in all respects as per direction of the
Engineer-in-Charge.

3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of Engineer-in-Charges 1 No. 30.00 Rs. thirty only. Each 30.00

4 Development of bore well and yield testing with air compressor through V-notch and disifection etc. as per IS 2800-1979 1 No. 500.00 Rs. Five hundred only. Mtr. 500.00
complete in all respect as per direction of the Engineer-in-Charge.

5 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and requirement of rotary 90 mtrs. 1725.00 Rs. One thousand seven Mtr. 155250.00
attachment from approved manufacturers complete in all respect as per direction of the Engineer-in-Charge. hundred twenty five only.

6 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding transportation of 15 Hrs 1250.00 Rs. One thousand two Hr. 18750.00
equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as per direction of Engineer-in- hundred fifty only.
Charges.

7 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch as per IS 2800- 10 Hrs 1200.00 Rs. One thousand two Hr. 12000.00
1979 inclluding transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as hundred only.
per direction of Engineer-in-Charges.

8 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia slotted pipe as per IS 10 mtrs. 300.00 Rs. Three hundred only. Mtr. 3000.00
as per 4270-2001 with upto date ammendments welded and joints into bore hole in vertical position i/c cost of all cutting,
threading and welding of pipe etc within all leads and lifts complete in all respects per directions of the Engineer -in- Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks as per IS 1 No. 830.00 Rs. Eight hundred thirty only. Each 830.00
2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per directions of the
Engineer -in- Charge.

10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an average specific 90 mtrs. 250.00 Rs. Two hundred fifty only. Mtr. 22500.00
gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe IS 4097-1967 with upto date amendments, if
any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to the entire depth of the
bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

558160.00
(Rs. Five lac fifty eight thousand one hundred
sixty only).
 Executive Engineer
IPH Division No.II Una.

REVISED SCHEDULE OF QUANITY.

NAME OF WORK:-Imp of LWSS Dharamsala Mahantan, Behar Bhatehar and Ghangret in Tehsil Amb Distt. Una (HP).(SH: Drilling , Tendered Cost:- Rs. 558,160.00 only
Lowering and development of 7" bore (Mini T/Well) in a depth of 90 mtrs.in village Dharamsala Mahantan) Estimated Cost:- Rs. 473,192.00 only
Earnest Money :- Rs. 9,464.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 Transportation of suitable truck mounted DTH & ODEX/ Percussion/ Calyx/ RC / Rotary drilling rig along with necessary 1 Job. 5550.00 Rs. Five thousand five Each 5550.00
accessories etc to the site of work & erection of rig including leveling etc complete in all respects as per directions of Engineer- hundred fifty only.
in-Charges.

2 Drilling bores of 200 to 300mm dia as per IS 2800: 1979 using DTH & ODEX/ Percussion/ Calyx/ RC / Rotary method required 90 mtrs. 3800.00 Rs. Three thousand eight Mtr. 342000.00
for drilling in collapsible strata conglomerate, boulders, pebbles, gravels, silt, clay, etc including cost of attachments , hundred only.
extractable casing,consumable stores, bits, water, POL etc. in annular space etc.complete in all respects as per direction of the
Engineer-in-Charge.

3 Collection and preservation of soil samples in polythene bags complete in all respect as per direction of Engineer-in-Charges 1 No. 30.00 Rs. thirty only. Each 30.00

4 Development of bore well and yield testing with air compressor through V-notch and disifection etc. as per IS 2800-1979 1 No. 500.00 Rs. Five hundred only. Mtr. 500.00
complete in all respect as per direction of the Engineer-in-Charge.

5 Suply and lowering of IS marked 175mm dia 6.4 mm thick MSERW casing pipe as per IS 4270--2001 and requirement of rotary 90 mtrs. 1700.00 Rs. One thousand seven Mtr. 153000.00
attachment from approved manufacturers complete in all respect as per direction of the Engineer-in-Charge. hundred only.

6 Development of bore well with 1000-CFM air-compressor through V notch as per IS 2800-1979 inclluding transportation of 15 Hrs 1250.00 Rs. One thousand two Hr. 18750.00
equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as per direction of Engineer-in- hundred fifty only.
Charges.

7 Development/ establishment of discharges of bore well and yield testing with subribale pump through V notch as per IS 2800- 10 Hrs 1200.00 Rs. One thousand two Hr. 12000.00
1979 inclluding transportation of equpment etc, to the site of work complete in all respect for the bore drilled by RC rig, as hundred only.
per direction of Engineer-in-Charges.

8 Pdg slotting arrangement as per IS 8110/1994-997 slot size 1.57x75mm and lowerung of 200/175mm dia slotted pipe as per IS 10 mtrs. 300.00 Rs. Three hundred only. Mtr. 3000.00
as per 4270-2001 with upto date ammendments welded and joints into bore hole in vertical position i/c cost of all cutting,
threading and welding of pipe etc within all leads and lifts complete in all respects per directions of the Engineer -in- Charge.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks as per IS 1 No. 830.00 Rs. Eight hundred thirty only. Each 830.00
2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per directions of the
Engineer -in- Charge.

10 Supplying and packing of gravel, consisting of hard quartz or other suitable material with 175mm / 125mm an average specific 90 mtrs. 250.00 Rs. Two hundred fifty only. Mtr. 22500.00
gravity of not less than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free from impurities such as
shafe,shale,mica,felspar,clay,sand,dirt loam,haematte and organic material as pe IS 4097-1967 with upto date amendments, if
any, around intake of tubewell with minium thickness of shroud around screen generally 100 mm to the entire depth of the
bore as per 2800(Part-I ) 1991 with upto date amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

558160.00
 (Rs. Five lac fifty eight thousand one hundred
sixty only).

Executive Engineer
IPH Division No.II Una.
REVISED SCHEDULE OF QUANITY.
NAME OF WORK:-IMPROVEMENT OF LWSS BADOLI TIURI - 2ND IN TEHSIL AMB DISTT. UNA (HP) Tendered Cost:- Rs. 977,729.00 only
(SH: Drilling, lowering of assembly and development of T/well 140 mtrs deep). Estimated Cost:- Rs. 1,184,897.00 only
Earnest Money :- Rs. 23,698.00 only
Time: 3 Months.
S. Sub head and item of work. Qty. Rate in Unit. Amount.
No. Fig. Words.
1 Transportation of Rig along with allied accessories etc. complete including errection and levelling at site, through all kinds of 1 Job. -- NIL each 0.00
roads, approaches fields errection and levelling at site, through all kinds of roads, approaches fields etc. in all leads and lifts
completed in all respects as per the directions of Engineer - in-Charge.

2 Earth work in foundatrion for digging Tubewell in all kinds of soils including dewatering ,shoring, struting from GL upto 3mtrs. 2.36 cum -- NIL cum 0.00
including disposing excavated soil in all leads and lift complete in all respect as per the directions of Engineer -in-Charge.

3 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date amnedments,if any,with RC Rig drilling
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe conforming to IS 4270-2001 with up-to-date
amendements,if any, in all kind of soils,boulders,rocks,collapsible strata,sturated soils,artesian conditions including the cost of
all consumable,stores,water,fuel,lubricants and other accessories etc. complete in all respectsd as per the directions of the
Engineer -in -Charge.

i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 27 mtrs. -- NIL mtr. 0.00
mentioned above,from 3-30 mtrs below ground level within all leads and lifts.

ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 30 mtrs. -- NIL mtr. 0.00
mentioned above,from 30-60 mtrs below ground level within all leads and lifts.

iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 30 mtrs. 4099.00 Rs. Four thousand ninety nine mtr. 122970.00
mentioned above,from 60-90 mtrs below ground level within all leads and lifts. only.

iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to-date amendments,if any, of suitable sizes as 60 mtrs. 5499.00 Rs. Five thousand four mtr. 329940.00
mentioned above,from 90-140 mtrs below ground level within all leads and lifts. hundred ninety nine only.

4 Collection ,preservaion and display of suitable size sample box with top lid and locking arrangement till handing over of the 1 No. 499.00 Rs. Four hundred ninety nine each 499.00
tube well to the department complete in all respects as per direction of the Engineer -in-Charge. only.
5(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 300 mm dia nominal size 8 mm 60 mtrs. 3750.00 Rs. Three thousand seven mtr. 225000.00
thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to I.S 4270-2001 with up-todate amendments, hundred fifty only.
if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of the Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 300 mm dia (1020 slots 5 mtrs. 4000.00 Rs. Four thousand only. mtr. 20000.00
per mtrs) nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm (Screwed End Socketted), conforming to I.S
4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc.
including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the
directions of the Engineer -in-Charge.

6 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in-Charge, the material of M.S taper/reducer shall 1 No. 2500.00 Rs. Two thousand five each 2500.00
be equivalent to parent pipe material and shall conform to chemical composition as per clasue 5.2 and mechanical properties hundred only.
as per clasue 6.1and table 1 of IS 4270-2001 with upto date amendments,if any, complete in all respect as per directions of
the Engineer -in -Charge.

7(a) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.pipe 200 mm dia nominal size 65 mtrs. 1900.00 Rs. one thousand nine mtr. 123500.00
housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming to I.S 4270-2001 with up- hundred only.
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into bore hole in
vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the directions of the
Engineer -in-Charge.

(b) Supplying & Lowering of IS marked Electric Resistance Welded Screwed End Socketed M.S.slotted pipe 200 mm dia (942 slots 20 mtrs. 2100.00 Rs. Two thousand one mtr. 42000.00
per mtrs) nominal size housing, 6.4 mm thick having out side dia mtrs. 219.10 mm (Screwed End Socketted), conforming to I.S hundred only.
4270-2001 with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential
joints,into bore hole in vertical position including cost of all scaffolding derricks,poles,clamps embedded in foundation etc.
including cost of all cutting,threading and welding of pipes etc. within all leads and lifts, complete in all respects as per the
directions of the Engineer -in-Charge.

8 Pdg. and fixing M.S cetralized guides at suitable spacing for each tube well as per IS 226-1991 with upto-date amendments,if 5 Nos. 299.00 Rs. Two hundred ninety nine each. 1495.00
any, within all leads and lifts ,1x4Nos. completed in all respects in all respects as per the directions of the Engineer -in-Charge. only.

9 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 mm/300 mm diameters with "U" hooks as per IS 1 No. 999.00 Rs. Nine hundred ninety nine each. 999.00
2800-1991 with up to date amendements ,if any, within all leads and lifts, complete in all respects per directions of the only.
Engineer -in- Charge.

10 Pdg. and fixing in position threaded iron cap with locking arrangements of approved design to prevent foreign matter from 1 No. 999.00 Rs. Nine hundred ninety nine each. 999.00
getting into bore hole,as required, within all leads and lifts, complete in all respects as per directions of the Engineer -in- only.
Charge.

11 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of not less 150 mtrs. 249.00 Rs. two hundred forty nine mtr. 37350.00
than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to rounded grains only.
with minimum angular features of size 2-3.35 mm , shall be free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt
loam,baematte and organic material as pe IS 4097-1967 with upto date amendments, if any, around intake of tubewell with
minium thickness of shroud around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with
upto date amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in- Charge.
 Supplying and packing of gravel, consisting of hard quartz or other suitable material with an average specific gravity of not less Rs. two hundred forty nine
than 2.5,not containing more than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to rounded grains only.
with minimum angular features of size 2-3.35 mm , shall be free from impurities such as shafe,shale,mica,felspar,clay,sand,dirt
loam,baematte and organic material as pe IS 4097-1967 with upto date amendments, if any, around intake of tubewell with
minium thickness of shroud around screen generally 100 mm to the entire depth of the bore as per 2800(Part-I ) 1991 with
upto date amendments, if any, with in all leads and lifts complete in all respects as per direction of the Engineer -in- Charge.

12 Development of tubewell by back washing method,with air compressor of minimum 750 CFM capacity, pumping pipe of 200 30 Hours. 1600.00 Rs.one thousand six hundred Hour. 48000.00
mm size and air line of minimum 65 mm size or with other suitable method,till the well is thoroughly developed as per clause only.
4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all respects as per direction of the Engnieer -in- Charge.

13 Development of tubewell by continous over pumping method,with VT pump/ submersible pumps of suitable capacity not less 20 Hours. 799.00 Rs.seven hundred ninety nine Hour. 15980.00
than double the discharge established by the compressor method/ design discharge, untill the well is sand free as per IS- only.
11189-1985 up -to- date amendments, if any, complete in all respects as per directions of the Engineer -in- Charge .The draw
down and discharge to be established by running the VT/ Submersible pump continuosuly for 8 hours in the presence of officer
not less than the rank of Assistant Engineer.

14 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 with upto date amendments, if any, using 1 Job 2999.00 Rs.Two thousand nine Job 2999.00
plumb or plunger 6 mm smaller in dia within the inside diameter of the well casing.The results of the verticality test shall be hundred ninety nine only.
recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-to-date amendments, if any, as appended with
the tender documents and handed over complete in all respect as the directions of the Engineer -in- Charge.

15 Dismentalling of Rig or other allied accesssories after completion of job within all leads and lifts, complete in all respects as per 1 No. 2999.00 Rs.Two thousand nine Each. 2999.00
the directions of the Engineer -in- Charge. hundred ninety nine only.
16 Construction of barbed wire enclosure of minimum of size 2.5x2.5 m to safe gaurd the bore of tubewell with angle iron of size 1 No. 0.00 NIL Each. 0.00
40x40x6 mm 1.5 mtrs in height, ambedded in concrete block of 30x30x30 cm in all leads and lifts,complete in all respects as
per the directions of the Engineer -in- Charge.

17 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of IS 2800 (Part-II) -1979 with upto date 1 Job. 499.00 Rs. Four hundred ninety nine Each 499.00
amendmentes if any, as appended with the tender documents, in laminated form , in triplicate, complete in all respect as per only.
the directions of the Engineer-in-Charge.

977729.00
Rs. Nine lac seventy seven thousand seven hundred twenty
nine only.

Executive Engineer
IPH Division No.II Una.
Fitter (grade-I) 178.50 Each CLASS OF MSERW PIPES :-
Fitter (grade-II) 178.50 Each IS:1978 -1982
Painter 2nd class 154.00 Each IS: 4270-1992
Beldar 140.00 Each API-5L,Gr. X - 42
Bitumen 8.25 /kg API-5L, Gr.X - 46
Fuel wood 5.00 /kg API-5L, Gr.X - 52
Hessian cloth 20.00 /m 2 API-5L, Gr.X - 56
Gasket sheet 118.00 Each
Diameter(mm) 300 mm
O.Dia. 323.90 mm
Wall Th.(mm) 8.00 mm
I.Diameter 307.90 mm
Flange table 17
Wt./Rmt (Kg.) 62.320 Kg.
Diameter(mm) 200 mm
O.Dia. 219.10 mm
Wall Th.(mm) 6.40 mm
I.Diameter 206.30 mm
Flange table 17
Wt./Rmt (Kg.) 33.570 Kg.
Wt. Of Joint 37.365 Kg. 40 mm 0.96 0.18 0.18
Rate flange 54.00 / Kg 50 mm 0.96 0.18 0.18
Rate of MSREW Pipe 48.00 / Kg 65 mm 0.96 0.18 0.18
Length of pipe 6.00 /Rmt 80 mm 0.96 0.18 0.18
MT for pipes 570.00 Km 100 mm 1.20 0.30 0.30
M.T. for flanges 23.00 Km 125 mm 1.20 0.30 0.30
HL for all material 0.10 Km 150 mm 1.32 0.36 0.36
Welding Charges 2.50 /cm 200 mm 1.32 0.36 0.36
M.Tpt.For Pipe (rate) 4372.68 /MT 250 mm 1.56 0.48 0.48
H.L.For Pipe (rate) 101.37 /MT 300 mm 1.56 0.48 0.48
M.Tpt.For H.Material 308.47 /MT 350 mm 1.80 0.60 0.60
H.L.For H.Material 59.50 /MT 400 mm 1.80 0.60 0.60
Anti Corossive paint 115.50 /Rmt 450 mm 2.04 0.72 0.72
500 mm 2.16 0.78 0.78
600 mm 2.40 0.90 0.90

ANALYSIS OF RATE
Providing and lowering of ERW/E 8.00 mm conforming to IS: 4270-1992
bevelled edge M.S pipe 300 mm conforming to ISI specification No.4270/1992 in random length to 4 to 7 mtrs.
S.No. Description Qty. Rate Unit Amount
(A) MATERIAL:- (Detail of cost for 1 Rmt.)
i) 300 mm of MSERW pipe as per IS: 4270-1992 62.320 78.000 Kg 4860.96
and having its wall thickness of 8.00 mm thick having weight kg
62.32 Kg/Rmt
MSERW Pipe = 1.00 Rmt.
4860.96
Total 1.00 Rmt.

2% wastage for cutting threading welding and packer seat etc. on Rs. 4860.96 97.22

Lowering of pipe 1/4 hours mtrs depth @ Rs. 1030/ hours. 0.250 1030.000 Hr. 257.50

Carriage of pipe from Gaziabad to Nangal Dam railway stat 372 KM 0.062 666.600 Tonne 41.33
Carriage of pipe from Nangal Dam railway station to site of 20 KM 1.00 49.68 Mtr 49.68
5306.69

Add 10% CP and 5% Over Head Charges on 5306.69 796.00

6102.69
Add 12% GST on Rs. 5306.69 636.80
Add 1% LC 6102.69 61.03
Cost of Pipe for 1 Rmt. 6800.52
Say Rs. 6800.50

Rate for slotted pipe.

 Rate for supplying and lowering of 3oomm dia 8.0mm thick M.S. pipe. 6800.50

Add 30% convertion of Blind Pipe into Slotted pipe 2040.15

8840.65
Say Rs. 8840.65

Executive Engineer,
Jalshakti Division 1 Una

ANALYSIS OF RATE
Providing and lowering of ERW/E 8.00 mm conforming to IS: 4270-1992
bevelled edge M.S pipe 200 mm conforming to ISI specification No.4270/1992 in random length to 4 to 7 mtrs.
S.No. Description Qty. Rate Unit Amount
(A) MATERIAL:- (Detail of cost for 1 Rmt.)
i) 33.570 mm of MSERW pipe as per IS: 4270-1992 33.570 78.000 Kg 2618.46
and having its wall thickness of 6.40 mm thick having weight kg
33.57 Kg/Rmt
MSERW Pipe = 1.00 Rmt.
2618.46
Total 1.00 Rmt.

2% wastage for cutting threading welding and packer seat etc. on Rs. 2618.46 52.37

Lowering of pipe 1/4 hours mtrs depth @ Rs. 1030/ hours. 0.250 1030.000 Hr. 257.50

Carriage of pipe from Gaziabad to Nangal Dam railway stat 372 KM 0.034 666.600 Tonne 22.66
Carriage of pipe from Nangal Dam railway station to site of 20 KM 1.00 28.15 Mtr 28.15
2979.14

Add 10% CP and 5% Over Head Charges on 2979.14 446.87

3426.01
Add 12% GST on Rs. 2979.14 357.50
Add 1% LC 3426.01 34.26
Cost of Pipe for 1 Rmt. 3817.77
Say Rs. 3817.75

Rate for slotted pipe.

Rate for supplying and lowering of 3oomm dia 8.0mm thick M.S. pipe. 3817.75

Add 30% convertion of Blind Pipe into Slotted pipe 1145.33

4963.08
Say Rs. 4963.10

Executive Engineer,
Jalshakti Division 1 Una
 ii) MS flanges i/c nuts & bolts of table:- #REF! TOTAL 4958.18 1)
No.of flanged joints = 0.17 Nos.
Wt. Of one Joint = 37.365 Kg
Total wt. Of joints = 6.228 Kg 6.228 54.00 Kg 336.29
Add 4 % HPST on Rs. 336.29 (+) 13.45
iii) Welding flanges with pipes TOTAL 349.74 2)
= 2 x 2 x 2 x 17 x p 32.39 cms. 135.67 2.50 cm 339.19
TOTAL 339.19 3)
iv) Anti corrossive treatment of pipe for dia:- #REF! 115.50 Rmt #REF!
TOTAL #REF! 4)
v) Rubber Gasket 3 mm thick for pipe dia:- 0.17 118.00 Nos. 19.67
(B) Labour:- TOTAL 19.67 5)
i) Labour for laying 514 Kg of pipe with flanges:- 68.55 0.6488 Kg 44.47
Type Qty Rate Amt.
Fitter-I 0.20 178.50 35.70
Fitter-II 0.20 178.50 35.70
Beldar 1.60 140.00 224.00
Sunderies LS 38.10
Total 333.50
Labour per Kg 0.6488
ii) Labour for Jointing 10 Joints:- 0.17 38.98 / joint 6.50
Type Qty Rate Amt.
Fitter-I 0.48 178.50 85.68 TOTAL 50.97 6)
Fitter-II 0.48 178.50 85.68
Beldar 1.56 140.00 218.40
Total 389.76
Cost per Joint 38.98
( C) Carriage:-
i) Carriage of pipe from Gaziabad to nearest road head:-
(a) By M.T. ### Km 0.062 4372.68 Tonne 271.11
(b) By Head Load 0.10 Km. 0.062 101.37 Tonne 6.28
ii) Carriage of flanges from Sub Divisional Store to site of work :-
(a) By Mechanical Transport 23.00 Km. 0.00623 308.47
Tonne 1.92
(b) By Head Load 0.10 Km. 0.00623 59.50
Tonne 0.37
TOTAL 279.68 7)
TOTAL (1 to7) #REF!
Add 10% C.P. Except cost of Pipe & Flange #REF! (+) #REF!
Add 5% O.H.C. Except cost of Pipe & Flange #REF! (+) #REF!
G.TOTAL #REF!
COST PER RMT = #REF!
SAY Rs. #REF!
ANALYSIS OF RATE PER RMT.
Applying three coats of hot bitumen on exposed surface of MSERW Pipe 300 mm Pipe having Wall Thickness of
8.00 mm & with Inner & Outer diameter 323.90 & ### mm respectively including wrapping these pipes
hessian cloth,one outer coat initially,subsequent coat while wrapping the pipe with hessian cloth & one coat on inner
surface of pipe.
S.No. Description Qty. Rate Unit Amount
1) MATERIAL
I) Bitumen @ 1.45 Kg/m2 for 3 coats=3x10x1.45=43.50 43.50 8.25 KG 358.88
ii) Fuel wood = 3.50/17x43.5 = 8.95 Kg 8.95 5.00 KG 44.75
iii)Hessian cloth for wrapping = 1.30 x 10 =13 m2 13.00 20.00 M2 260.00
TOTAL 663.63 1)
2) CARRIAGE of material Job 60.00 LS 60.00 2)
3) LABOUR
Painter 2nd class 0.72 154 Each 110.88
Beldar 2.00 140 Each 280.00
Sundries LS 39.09
TOTAL 429.97 3)
G.Total (1 to 3) 1153.60 SURFACE AREA OF PIPE
COST FOR 10 m2 1153.60 WALL THICKNESS OF PIPE = 8.00 mm
COST PER m2 115.36 OUTER SURFACE = 2.0351 M 2
INNER SURFACE = 0.9673 M 2
AVERAGE AREA = 1.0008 M 2
RATE PER RMT Rs. 115.50 /Rmt.

EXECUTIVE ENGINEER,
I&PH DIVISION,BARSAR.

ANALYIS OF RATE
Providing,laying,jointing & testing MSERW Pipe flangrd bends of all degrees manufacured from MSERW pipe as per IS:1978-82
of grade Yst - 210 parent pipe of relevant requirement with 3-4 cuts of radius not less than 5 times of pipe to meet the code
requirement with welding of all pieces as per code requirement.The MSERW pipe shall have out side coating of primer as per
AWWA specification C: 203 - 1978 followed by a flood coat of coal tar approximately 3/32" thick and hessian cloth wrapping
after completely dipping in coal tar and inside coating shall be of black readymade bitumionous antocorossive paint over coat
of primer as per AWWA specification C:203-1978 in factory.The MS flanges are to be provided on each joint conforming to IS
6392-1971 & welding of flanges as per IS:816-1969 with electrods as per IS :814-1991 i/c required Nos.& size of MS nuts &
bolts as per IS :1369-1967 and asbestos fibre jointing gasket sheet not less than 3.00 mm in thickness as per IS :2717-
1998.The welding of flanges to be done on both faces in two layers tomake the joint leak proof as per entire satisfaction of
Engineer in Charge within all leads & lifts.
MS Flange 300 mm Dia.& Flange of table 17 (DETAIL OF ONE BEND)
S.No. Description Qty. Rate Unit Amount
1) MATERIALS:-
( THE LENGTH OF BEND 0.80 Rmt) 28.3568 49.500 KG 1403.66
(a) 300 mm DIA. OF MSERW PIPE AS PER (Gr. #REF!
IS: 4270-1992 & HAVING THICKNESS OF 4.50 mm
& HAVING WT. OF PIPE/BEND 35.446 Kg/Rmt.
Add Excise duty @ 12.36 % = (+) 173.49
including 3 % Edu.Cess TOTAL 1577.15
Add C.S.T. @ 2.00 % = (+) 31.54
Add HP Vat @ 5.00 % = (+) 80.43
Add Inspection charges @ 1.00 % = (+) 14.04
TOTAL 1703.16(I )
(b) MS Flanges i/c nuts & bolts of reqd.sizes.
No.of flanged joints = 1.000 Nos.
Wt.of one Joint = 37.365 Kg
Total wt.of joints = 37.365 Kg 37.365 55.00 KG. 2055.08
Add HP Vat @ 5.00 % = (+) 102.75
TOTAL 2157.83(ii)
2) Welding flanges with pipes = 2X2x2x1x3.141x 32.39 Cms 814.05 2.50 CMS. 2035.12
TOTAL 2035.12(iii)
3) Anti corrossive treatment of pipe for dia. 0.80 115.50 Rmt 92.40
4) Rubber jointing Gasket 3 mm thick for pipe dia. 1.00 186.00 Each 186.00
5) Labour TOTAL 278.40(iv)
Labour for laying 514 Kg of pipe with flanges
Type Qty Rate Amount 65.7218 0.6488 KG. 42.64
Fitter-I 0.20 178.50 35.70
Fitter-II 0.20 178.50 35.70
Beldar 1.60 140.00 224.00
Sunderies LS 38.10
Total 333.50
Labour per Kg. 0.6488
Labour for Jointing 10 Joints
Type Qty Rate Amount 1.00 38.98 Each 38.98
Fitter-I 0.48 178.50 85.68
Fitter-II 0.48 178.50 85.68
Beldar 1.56 140.00 218.40
Total 389.76
Cost per Joint 38.98 TOTAL 81.62( v)
6) Carriage
(i) Carriage of pipe from Gaziabad to site of work
(a) By M.T. 369.00 KM 0.02836 2801.44 MT 0.79
(b) By Head Load 0.10 KM 0.02836 101.37 MT 0.03
(ii) Carriage of MS Flange from Divisional store to site of work
(a) By M.T. 23.00 KM 0.03737 308.47 MT 11.53
(b) By Head Load 0.10 KM 0.03737 59.50 MT 2.22
TOTAL 14.57(vi)
7) Cutting of pipe ( in 3 cut & 4 pieces) & welding the pieces
in two layers Outer Diameter. 32.39 Cms 916.17 3.00 Cms 2748.52
TOTAL 2748.52(vii)
GRAND TOTAL (i to vii) 9019.22
Add 10% C.P. except cost of pipe & MS Flanges 5158.23 515.82
Add 5% Over head Charges 9019.22 450.96
COST OF1.00 No.BEND 9986.01
Add 1% extra for labour cess. 99.86
10085.87
SAY Rs. 10085.85
 EXECUTIVE ENGINEER,
I&PH DIVISION NO.II UNA

ANALYIS OF RATE
Providing,laying,jointing & testing G.I.Pipe flangrd bends of all degrees manufacured from G.I.(Heavy or Medium class) parent
pipe of relevant requirement with 3-4 cuts of radius not less than 5 times of pipe to meet the code requirement with welding of
all pieces as per code requirement.The MS flanges are to be provided on each joint conforming to IS 6392-1971 & welding of
flanges as per IS:816-1969 with electrods as per IS :814-1991 i/c required Nos.& size of MS nuts & bolts as per IS :1369-1967
and asbestos fibre jointing gasket sheet not less than 3.00 mm in thickness as per IS :2717-1998.The welding of flanges to be
done on both faces in two layers tomake the joint leak proof as per entire satisfaction of Engineer in Charge within all leads &
lifts.

MS Flange 100 mm Dia.& Flange of table 17 (DETAIL OF ONE BEND)

S.No. Description Qty. Rate Unit Amount
1) MATERIALS:-
( AVERAGE LENGTH OF BEND = 0.80 MTS.) 0.80 512.00 Rmt. 409.60
(a) 100 mm DIA. OF GMS TUBES (1239 - 1990) MEDIUM CLASS (issued Free of cost)
AND HAVING WALL THICKNESS OF 4.50 mm & weight / Rmt. 14.80
Kg/Rmt.
TOTAL 409.60(I )
(b) MS Flanges i/c nuts & bolts of reqd.sizes.
No.of flanged joints 1.00 Nos.
Wt. Of one Joint 9.058 Kg
Total wt.of joints 9.058 Kg 9.058 54.00 KG. 489.13
Add HP Vat @ 4.00 % = (+) 19.57
TOTAL 19.57(ii)
2) Welding flanges with pipes = 2X2x2x1.00 x11.50
px Cms. 289.03 2.50 CMS. 722.57
TOTAL 722.57(iii)
4) Rubber jointing Gasket 3 mm thick for pipe dia. 1.00 0.00 Each 0.00
5) Labour TOTAL 0.00(iv)
Labour for laying 514 Kg of pipe with flanges
Type Qty Rate Amount 20.898 0.6488 KG. 13.56
Fitter-I 0.20 178.50 35.70
Fitter-II 0.20 178.50 35.70
Beldar 1.60 140.00 224.00
Sunderies LS 38.10
Total 333.50
Labour per Kg. 0.6488
Labour for Jointing 10 Joints
Type Qty Rate Amount 1.00 27.51 Each 27.51
Fitter-I 0.30 178.50 53.55
Fitter-II 0.30 178.50 53.55
Beldar 1.20 140.00 168.00
Total 275.10
Cost per Joint 27.51 TOTAL 41.07( v)
6) Carriage
(i) Carriage of pipe from Divisional I&PH Store to site of work
(a) By M.T. 23.00 Km 0.01180 308.47 MT 3.64
(b) By Head Load 0.10 Km 0.01180 101.37 MT 1.20
(ii) Carriage of MS Flange from Divisional I&PH Store to site of work
(a) By M.T. 23.00 Km ### 0.00 MT 0.00
(b) By Head Load 0.10 Km ### 0.00 MT 0.00
TOTAL 4.84(vi)
7) Cutting of pipe ( in 3 cut & 4 pieces) & welding the pieces
 in two layers Outer Diameter. 11.50 Cms. 325.29 2.50
CMS. 813.22
TOTAL 813.22(vii)
GRAND TOTAL (i to vii) 2010.87
Add 10% C.P. except cost of pipe & MS Flanges 1581.70 158.17
Add 5% Over head Charges except cost of pipe & MS Flanges 1581.70 79.09
COST OF1.00 No.BEND 2248.13
SAY Rs. 2248.15

EXECUTIVE ENGINEER,
I&PH DIVISION,BILASPUR.

ANALYSIS OF RATE
Providing Circumferencial Butt Welded joints by electrical arc welding to 300 mm dia MSERW Pipe as per IS:3589-2001,
welded in requisite number of weld runs so as to achieve the minimum effective throat thickness of weld conforming to IS :
816-1969 specifications, by using welding electrodes of 2.50 mm to 6.30 mm of Advani Oerlikon (Adore) - CITOJET / ESAB
make, conforming to IS:814-1991, at site of work complete in all respects, including manual / mechanical handling of pipes in
all leads and lifts to the entire satisfaction of Engineer-in-Charge.

S.No. DESCRIPTION OF ITEM QTY. RATE UNIT AMT.

(A) MATERIAL:-
MSERW Pipe = 100.00 Rmt.
Add 2 % for bends = 2.00 Rmt.
Total 102.00 Rmt.

1) 300 mm diameter MSERW Pipe as per IS:3589-2001 3218.814 38.27 Kg 123184.01

Dia.of pipe = 300 mm and outer diameter ### mm T0TAL 123184.01
Wt of pipe = 31.557 Kg/Rmt & Wall Thickness of pipe 4.00 mm
Add Excise duty @ 8.24 % = (+) 10150.36
including 3 % Edu.Cess TOTAL 256518.38
Add C.S.T. @ 2.00 % = (+) 5130.37
Add HP Vat @ 4.00 % = (+) 10465.95
Add Inspection charges @ 1.00 % = (+) 1231.84
Total 273346.54
2) Welding of pipes by special rods
conforming to relevant codes
No.of Butt weld joints: = 17.000 Nos.
Nos.of Layers = 3.00 Nos.
Outer diameter of pipe 32.39 cms. 5189.57 3.00 Cms 15568.71 (B)
3) Manual / Mechanical charges of pipes with crane , winch crab, chain pullys,eire
ropes at sute of work
1.00 % of pipe cost of 273346.54 1.00 % 2733.47 (C)
Total (B + C ) 18302.18
Cost per joint = 1076.60
Say Rs. 1076.60
 1 2 3 4 5 6 7 8 9 10 11 12
MSERW Pipe IS:1978-82 Rate of pipe Weight of pipe We
Dia of Pipe O.D. Gasket Light Medium Heavy Light Medium Heavy FT - 5 FT - 11
40 mm 48.30 19.00 150.00 180.00 212.00 3.27 3.60 4.41 2.669
50 mm 60.30 24.00 180.00 197.00 232.00 4.15 5.16 6.26 2.907
65 mm 73.00 29.00 245.00 260.00 307.00 5.83 6.54 8.05 3.592
80 mm 88.90 35.00 335.00 355.00 419.00 6.89 8.53 10.40 6.053
100 mm 114.30 45.00 461.00 512.00 604.00 10.00 12.50 14.80 6.665
125 mm 141.30 56.00 0.00 712.00 760.00 0.00 16.40 18.40 9.644
150 mm 168.30 66.00 0.00 843.00 995.00 0.00 19.50 21.90 10.456
200 mm 219.10 86.00 Dia of Pipe O.D. Gasket Wall thickness 14.578 20.328
250 mm 273.10 108.00 Medium Heavy 19.704 27.089
300 mm 323.90 128.00 15 mm 21.80 9.00 2.60 3.20 26.255 29.855
450 mm 457.00 180.00 32 mm 42.90 17.00 3.20 4.00 54.448 90.530
125 mm 141.30 56.00 0.00 178.50 153.00 0.00 16.40 18.40 9.644
150 mm 168.30 66.00 0.00 178.50 153.00 0.00 19.50 21.90 10.456
200 mm 219.10 86.00 Dia of Pipe O.D. Gasket Wall thickness 14.578 20.328
250 mm 273.10 108.00 Medium Heavy 19.704 27.089
300 mm 323.90 128.00 15 mm 21.80 9.00 2.60 3.20 26.255 29.855
450 mm 457.00 180.00 32 mm 42.90 17.00 3.20 4.00 54.448 90.530
500 mm 508.00 200.00 40 mm 48.80 19.00 3.20 4.00 59.062 90.530
550 mm 559.00 220.00 50 mm 60.80 24.00 3.60 4.50
600 mm 610.00 240.00 65 mm 76.60 30.00 3.60 4.50 77.608 123.498
700 mm 711.00 280.00 80 mm 89.50 35.00 4.00 4.80 97.191 167.798
800 mm 813.00 320.00 100 mm 115.00 45.00 4.50 5.40 135.390 240.852
900 mm 914.00 360.00 125 mm 140.80 55.00 4.80 5.40 163.579 284.943
1000 mm 1016.00 400.00 150 mm 166.50 66.00 4.80 5.40 196.377 377.114
MSERW Pipe IS:3589-2001
Dia of Pipe O.D. Gasket
200 mm 219.10 86.00
250 mm 273.00 107.00
300 mm 323.90 128.00
350 mm 355.60 140.00
400 mm 406.40 160.00
450 mm 457.00 180.00
500 mm 508.00 200.00
1)

2)

3)

4)

5)

6)

7)

1)
2)

3)
 FOR MSERW BENDS :-
Diameter(mm) 150 mm
O.Dia. 114.30 mm
Wall Th.(mm) 7.90 mm
Class of Pipe Yst -210 Yst -240
Weight of pipe per Rmt. 20.729

Gasket sheet 0.00 Each

11 12 13 14 15 16 17 18
FT - 5 FT - 11 FT - 17 FT - 23 FT - 28 FT - 34 FT - 38 FT - 42
Flange table 34
Wt. Of Joint 43.240 Kg.
Rate flange 54.00 / Kg
Rate contract of MSERW 48.00 /Kg
MT for pipes 64.00 Km
HL for Pipe 0.10 Km
Length of pipe 6.00 /Rmt
Rate of MSERW Tubes (ByM/T) 613.10 /MT
Rate for GMS Tubes (ByH/L) 101.37 /MT
MT for Flanges 23.00 Km
(I ) HL for Flanges 0.10 Km
Rate for H.Material (ByM/T) 308.47 /MT
Rate for H.Material (ByH/L) 59.50 /MT

(ii)

(iii)

(iv)

( v)

(vi)

(vii)
 FOR BENDS :-
Diameter(mm) 100 mm
O.Dia. 115.00 mm
Wall Th.(mm) 4.50 5.40 mm
Class of Pipe MEDIUM HEAVY
Weight of pipe per Rmt. 12.50 14.80 Kg.
Gasket sheet 45.00 Each
11 12 13 14 15 16 17 18
FT - 5 FT - 11 FT - 17 FT - 23 FT - 28 FT - 34 FT - 38 FT - 42
Flange table 17
Wt. Of Joint 9.058 Kg.
Rate flange 54.00 / Kg
Store issue rate of GI Pipe 512.00 / Rmt.
MT for pipes 23.00 Km
(I ) HL for Pipe 0.10 Km
Length of pipe 6.00 /Rmt
Rate for GMS Tubes (ByM/T) 308.47 /MT
Rate for GMS Tubes (ByH/L) 101.37 /MT
MT for Flanges 23.00 Km
HL for Flanges 0.10 Km
(ii) Rate for H.Material (ByM/T) 308.47 /MT
Rate for H.Material (ByH/L) 59.50 /MT
(iii)

(iv)

( v)

(vi)
(vii)

(B)

(C)
 13 14 15 16 17 18
Weight of Flange
FT - 17 FT - 23 FT - 28 FT - 34 FT - 38 FT - 42
4.022 5.033 8.717 9.932
5.211 5.801 9.390 12.124 14.469
6.193 8.145 12.576 16.935 19.687
8.351 9.886 15.172 20.060 22.989
9.058 14.408 20.746 27.486 32.414
11.803 19.588 29.911 44.400 54.905
15.047 23.656 43.240 62.937 77.547
21.299 30.055 41.914 78.554 108.079 132.019
29.980 44.880 71.411 104.546 163.103 195.985
37.365 64.454 104.520 142.902 261.255 317.977
122.343 188.243 226.104 615.023
11.803 19.588 29.911 44.400 54.905
15.047 23.656 43.240 62.937 77.547
21.299 30.055 41.914 78.554 108.079 132.019
29.980 44.880 71.411 104.546 163.103 195.985
37.365 64.454 104.520 142.902 261.255 317.977
122.343 188.243 226.104 615.023
143.929 260.609 298.504 757.036

220.878 281.206
241.210
311.347
386.563
544.921
 DETAIL OF MEASUREMENT
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli
consituency in Distt. Una HP (SH: Drilling , lowering of assembly and development of 125 mtrs deep
T/wells at village Lower Khad, Dharampur, Pandoga lower and Badhera)
S.No. Sub head and item of work. Unit. Qty.
1.00 Transportation of Rig along with allied accessories etc. complete including Job 1 Job.
errection and levelling at site, through all kinds of roads, approaches fields
errection and levelling at site, through all kinds of roads, approaches fields etc. in
all leads and lifts completed in all respects as per the directions of Engineer - in-
Charge.

2.00 Earth work in founation for digging of tubewell in all kinds of soils including cum 21.21 cum
dewatering, shoring, struting from GL upto 3 mtrs including disposing excavated
soil in all leads and lifts complete in all respect as per direction of the Engineer-in-
charge.
3.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date
amnedments,if any,with Direct Rotary Rig or combination drilling rig,Precussion Rig
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of
soils, boulders, rocks, collapsible strata,sturated soils,artesian conditions including
the cost of all consumable,stores,water,fuel,lubricants and other accessories etc.
complete in all respectsd as per the directions of the Engineer -in -Charge.

3.01 i) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 27 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 3-30 mtrs
below ground level within all leads and lifts.
3.02 ii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up- Mtr 30 Mtrs
to-date amendments,if any, of suitable sizes as mentioned above,from 30-60 mtrs
below ground level within all leads and lifts.
3.03 iii) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up- Mtr 30 Mtrs
to-date amendments,if any, of suitable sizes as mentioned above,from 60-90 mtrs
below ground level within all leads and lifts.
3.04 iv) Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up- Mtr 35 Mtrs
to-date amendments,if any, of suitable sizes as mentioned above,from 90-125 mtrs
below ground level within all leads and lifts.
4.00 Collection ,preservaion and display of suitable size sample box with top lid and Each 1 No.
locking arrangement till handing over of the tube well to the department complete
in all respects as per direction of the Engineer -in-Charge.
5.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 Mtr 50 Mtrs
mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 Mtr
Cage type "V" wire wound screens of size 300 mm ,8 mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Chrage.
5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe Mtr 4 Mtrs
300 mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm welded with up-
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all
respects as per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in- Each 1 No.
Charge, the material of M.S taper/reducer shall be equivalent to parent pipe
material and shall conform to chemical composition as per clasue 5.2 and
mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -
Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 Mtr 58 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 mtr
Cage type "V" wire wound screens of size 200 mm ,6.3mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 Mtr 11 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
Screwed End Socketted, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length,
welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as Each 5 Nos.
per IS 226-1991 with upto-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions of the
Engineer -in-Charge.
9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 Each 1 No.
mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up to date
amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.
10.00 Providing and fixing in position threaded iron cap with locking arrangements of Each 1 No.
approved design to prevent foreign matter from getting into bore hole,as required,
within all leads and lifts, complete in all respects as per directions of the Engineer -
in- Charge.
11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable Mtr 125 Mtrs
material with an average specific gravity of not less than 2.5,not containing more
than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free
from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and
organic material as pe IS 4097-1967 with upto date amendments, if any, around
intake of tubewell with minium thickness of shroud around screen generally 100
mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

12.00 Extraction of all sizes blind / casing pipe with machine starting from bottom of the
bore hole within all leads and lifts complete in all respects per directions of the
Engineer -in- Charge.
12.01 in contact with soil Mtr 125 Mtrs
12.02 Freely hanging Mtr 165 Mtrs
13.00 Development of tubewell by back washing method,with air compressor of minimum Hr 30 Hrs
750 CFM capacity, pumping pipe of 200 mm size and air line of minimum 65 mm
size or with other suitable method,till the well is thoroughly developed as per
clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all
respects as per direction of the Engnieer -in- Charge.

14.00 Development of tubewell by continous over pumping method,with VT pump/ Hr 20 Hrs

submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all
respects as per directions of the Engineer -in- Charge .The draw down and
discharge to be established by running the VT/ Submersible pump continuosuly for
8 hours in the presence of officer not less than the rank of Assistant Engineer.

15.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 Job 1 Job.
with upto date amendments, if any, using plumb or plunger 6 mm smaller in dia
within the inside diameter of the well casing.The results of the verticality test shall
be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-
to-date amendments, if any, as appended with the tender documents and handed
over complete in all respect as the directions of the Engineer -in- Charge.

16.00 Dismentalling of Rig or other allied accesssories after completion of job within all Job 1 Job.
leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.
17.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of Job 1 Job.
IS 2800 (Part-II) -1979 with upto date amendmentes if any, as appended with the
tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.
 DETAIL OF MEASUREMENT
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli
consituency in Distt. Una HP (SH: Drilling , lowering of assembly and development of 150 mtrs deep
T/well at village Saloh)
S.No. Sub head and item of work. Unit. Qty.
1.00 Transportation of Rig along with allied accessories etc. complete including Job 1 Job.
errection and levelling at site, through all kinds of roads, approaches fields
errection and levelling at site, through all kinds of roads, approaches fields etc. in
all leads and lifts completed in all respects as per the directions of Engineer - in-
Charge.

2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date
amnedments,if any,with Direct Rotary Rig or combination drilling rig,Precussion Rig
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of
soils, boulders, rocks, collapsible strata,sturated soils,artesian conditions including
the cost of all consumable,stores,water,fuel,lubricants and other accessories etc.
complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 0-30 mtrs
below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 30-60 mtrs
below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 60-90 mtrs
below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 90-140 mtrs
below ground level within all leads and lifts.
2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 10 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 140-150 mtrs
below ground level within all leads and lifts.
3.00 Collection ,preservaion and display of suitable size sample box with top lid and Each 1 No.
locking arrangement till handing over of the tube well to the department complete
in all respects as per direction of the Engineer -in-Charge.
4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 Mtr 60 Mtrs
mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 Mtr
Cage type "V" wire wound screens of size 300 mm ,8 mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Chrage.
5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe Mtr 5 Mtrs
300 mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm welded with up-
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all
respects as per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in- Each 1 No.
Charge, the material of M.S taper/reducer shall be equivalent to parent pipe
material and shall conform to chemical composition as per clasue 5.2 and
mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -
Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 Mtr 70 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 mtr
Cage type "V" wire wound screens of size 200 mm ,6.3mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 Mtr 13 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
Screwed End Socketted, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length,
welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as Each 5 Nos.
per IS 226-1991 with upto-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions of the
Engineer -in-Charge.
9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 Each 1 No.
mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up to date
amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.
10.00 Providing and fixing in position threaded iron cap with locking arrangements of Each 1 No.
approved design to prevent foreign matter from getting into bore hole,as required,
within all leads and lifts, complete in all respects as per directions of the Engineer -
in- Charge.
11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable Mtr 150 Mtrs
material with an average specific gravity of not less than 2.5,not containing more
than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free
from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and
organic material as pe IS 4097-1967 with upto date amendments, if any, around
intake of tubewell with minium thickness of shroud around screen generally 100
mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum Hr 30 Hrs
750 CFM capacity, pumping pipe of 200 mm size and air line of minimum 65 mm
size or with other suitable method,till the well is thoroughly developed as per
clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all
respects as per direction of the Engnieer -in- Charge.

13.00 Development of tubewell by continous over pumping method,with VT pump/ Hr 20 Hrs

submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all
respects as per directions of the Engineer -in- Charge .The draw down and
discharge to be established by running the VT/ Submersible pump continuosuly for
8 hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 Job 1 Job.
with upto date amendments, if any, using plumb or plunger 6 mm smaller in dia
within the inside diameter of the well casing.The results of the verticality test shall
be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-
to-date amendments, if any, as appended with the tender documents and handed
over complete in all respect as the directions of the Engineer -in- Charge.

15.00 Dismentalling of Rig or other allied accesssories after completion of job within all Job 1 Job.
leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of Job 1 Job.
IS 2800 (Part-II) -1979 with upto date amendmentes if any, as appended with the
tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.
 DETAIL OF MEASUREMENT
NAME OF WORK:-Separate water supply schemes for village Dhuge, Loothre, Dittan, Dhilwan, Haleran,
Badewal, Bilna and Chandpur n Tehsil Haroli Distt. Una (HP) (SH: Drilling , lowering of assembly and
development of 200mtrs deep T/well at Chandpur )
S.No. Sub head and item of work. Unit. Qty.
1.00 Transportation of Rig along with allied accessories etc. complete including Job 1 Job.
errection and levelling at site, through all kinds of roads, approaches fields
errection and levelling at site, through all kinds of roads, approaches fields etc. in
all leads and lifts completed in all respects as per the directions of Engineer - in-
Charge.

2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date
amnedments,if any,with Direct Rotary Rig or combination drilling rig,Precussion Rig
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of
soils, boulders, rocks, collapsible strata,sturated soils,artesian conditions including
the cost of all consumable,stores,water,fuel,lubricants and other accessories etc.
complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 0-30 mtrs
below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 30-60 mtrs
below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 60-90 mtrs
below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 90-140 mtrs
below ground level within all leads and lifts.
2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 140-190 mtrs
below ground level within all leads and lifts.
2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 10 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 190-200 mtrs
below ground level within all leads and lifts.
3.00 Collection ,preservaion and display of suitable size sample box with top lid and Each 1 No.
locking arrangement till handing over of the tube well to the department complete
in all respects as per direction of the Engineer -in-Charge.
4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 Mtr 98 Mtrs
mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 Mtr
Cage type "V" wire wound screens of size 300 mm ,8 mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Chrage.
5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe Mtr 9 Mtrs
300 mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm welded with up-
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all
respects as per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in- Each 1 No.
Charge, the material of M.S taper/reducer shall be equivalent to parent pipe
material and shall conform to chemical composition as per clasue 5.2 and
mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -
Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 Mtr 71 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 mtr
Cage type "V" wire wound screens of size 200 mm ,6.3mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 Mtr 20 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
Screwed End Socketted, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length,
welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as Each 5 Nos.
per IS 226-1991 with upto-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions of the
Engineer -in-Charge.
9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 Each 1 No.
mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up to date
amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.
10.00 Providing and fixing in position threaded iron cap with locking arrangements of Each 1 No.
approved design to prevent foreign matter from getting into bore hole,as required,
within all leads and lifts, complete in all respects as per directions of the Engineer -
in- Charge.
11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable Mtr 200 Mtrs
material with an average specific gravity of not less than 2.5,not containing more
than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free
from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and
organic material as pe IS 4097-1967 with upto date amendments, if any, around
intake of tubewell with minium thickness of shroud around screen generally 100
mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum Hr 30 Hrs
750 CFM capacity, pumping pipe of 200 mm size and air line of minimum 65 mm
size or with other suitable method,till the well is thoroughly developed as per
clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all
respects as per direction of the Engnieer -in- Charge.

13.00 Development of tubewell by continous over pumping method,with VT pump/ Hr 20 Hrs

submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all
respects as per directions of the Engineer -in- Charge .The draw down and
discharge to be established by running the VT/ Submersible pump continuosuly for
8 hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 Job 1 Job.
with upto date amendments, if any, using plumb or plunger 6 mm smaller in dia
within the inside diameter of the well casing.The results of the verticality test shall
be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-
to-date amendments, if any, as appended with the tender documents and handed
over complete in all respect as the directions of the Engineer -in- Charge.

15.00 Dismentalling of Rig or other allied accesssories after completion of job within all Job 1 Job.
leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of Job 1 Job.
IS 2800 (Part-II) -1979 with upto date amendmentes if any, as appended with the
tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.
 DETAIL OF MEASUREMENT
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli
consituency in Distt. Una HP (SH: Drilling , lowering of assembly and development of 230 mtrs deep
T/well at village Ispur)
S.No. Sub head and item of work. Unit. Qty.
1.00 Transportation of Rig along with allied accessories etc. complete including Job 1 Job.
errection and levelling at site, through all kinds of roads, approaches fields
errection and levelling at site, through all kinds of roads, approaches fields etc. in
all leads and lifts completed in all respects as per the directions of Engineer - in-
Charge.

2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date
amnedments,if any,with Direct Rotary Rig or combination drilling rig,Precussion Rig
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of
soils, boulders, rocks, collapsible strata,sturated soils,artesian conditions including
the cost of all consumable,stores,water,fuel,lubricants and other accessories etc.
complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 0-30 mtrs
below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 30-60 mtrs
below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 60-90 mtrs
below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 90-140 mtrs
below ground level within all leads and lifts.
2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 140-190 mtrs
below ground level within all leads and lifts.
2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 40 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 190-230 mtrs
below ground level within all leads and lifts.
3.00 Collection ,preservaion and display of suitable size sample box with top lid and Each 1 No.
locking arrangement till handing over of the tube well to the department complete
in all respects as per direction of the Engineer -in-Charge.
4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 Mtr 112 Mtrs
mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 Mtr
Cage type "V" wire wound screens of size 300 mm ,8 mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Chrage.
5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe Mtr 11 Mtrs
300 mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm welded with up-
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all
respects as per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in- Each 1 No.
Charge, the material of M.S taper/reducer shall be equivalent to parent pipe
material and shall conform to chemical composition as per clasue 5.2 and
mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -
Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 Mtr 85 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 mtr
Cage type "V" wire wound screens of size 200 mm ,6.3mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 Mtr 20 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
Screwed End Socketted, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length,
welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.

8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as Each 5 Nos.
per IS 226-1991 with upto-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions of the
Engineer -in-Charge.
9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 Each 1 No.
mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up to date
amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.
10.00 Providing and fixing in position threaded iron cap with locking arrangements of Each 1 No.
approved design to prevent foreign matter from getting into bore hole,as required,
within all leads and lifts, complete in all respects as per directions of the Engineer -
in- Charge.
11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable Mtr 230 Mtrs
material with an average specific gravity of not less than 2.5,not containing more
than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free
from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and
organic material as pe IS 4097-1967 with upto date amendments, if any, around
intake of tubewell with minium thickness of shroud around screen generally 100
mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum Hr 30 Hrs
750 CFM capacity, pumping pipe of 200 mm size and air line of minimum 65 mm
size or with other suitable method,till the well is thoroughly developed as per
clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all
respects as per direction of the Engnieer -in- Charge.

13.00 Development of tubewell by continous over pumping method,with VT pump/ Hr 20 Hrs

submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all
respects as per directions of the Engineer -in- Charge .The draw down and
discharge to be established by running the VT/ Submersible pump continuosuly for
8 hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 Job 1 Job.
with upto date amendments, if any, using plumb or plunger 6 mm smaller in dia
within the inside diameter of the well casing.The results of the verticality test shall
be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-
to-date amendments, if any, as appended with the tender documents and handed
over complete in all respect as the directions of the Engineer -in- Charge.

15.00 Dismentalling of Rig or other allied accesssories after completion of job within all Job 1 Job.
leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of Job 1 Job.
IS 2800 (Part-II) -1979 with upto date amendmentes if any, as appended with the
tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.
 DETAIL OF MEASUREMENT
NAME OF WORK:-Construction of irrigation tubewells for left out area of various villages of Haroli
consituency in Distt. Una HP (SH: Drilling , lowering of assembly and development of 250 mtrs deep
T/well at village Rora)
S.No. Sub head and item of work. Unit. Qty.
1.00 Transportation of Rig along with allied accessories etc. complete including Job 1 Job.
errection and levelling at site, through all kinds of roads, approaches fields
errection and levelling at site, through all kinds of roads, approaches fields etc. in
all leads and lifts completed in all respects as per the directions of Engineer - in-
Charge.

2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date
amnedments,if any,with Direct Rotary Rig or combination drilling rig,Precussion Rig
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of
soils, boulders, rocks, collapsible strata,sturated soils,artesian conditions including
the cost of all consumable,stores,water,fuel,lubricants and other accessories etc.
complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 0-30 mtrs
below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 30-60 mtrs
below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 60-90 mtrs
below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 90-140 mtrs
below ground level within all leads and lifts.
2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 140-190 mtrs
below ground level within all leads and lifts.
2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 190-240 mtrs
below ground level within all leads and lifts.
2.07 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 10 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 240-250 mtrs
below ground level within all leads and lifts.
3.00 Collection ,preservaion and display of suitable size sample box with top lid and Each 1 No.
locking arrangement till handing over of the tube well to the department complete
in all respects as per direction of the Engineer -in-Charge.
4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 Mtr 122 Mtrs
mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 Mtr
Cage type "V" wire wound screens of size 300 mm ,8 mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Chrage.
5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe Mtr 12 Mtrs
300 mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm welded with up-
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all
respects as per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in- Each 1 No.
Charge, the material of M.S taper/reducer shall be equivalent to parent pipe
material and shall conform to chemical composition as per clasue 5.2 and
mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -
Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 Mtr 92 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 mtr
Cage type "V" wire wound screens of size 200 mm ,6.3mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 Mtr 22 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
Screwed End Socketted, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length,
welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.
8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as Each 5 Nos.
per IS 226-1991 with upto-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions of the
Engineer -in-Charge.
9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 Each 1 No.
mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up to date
amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.
10.00 Providing and fixing in position threaded iron cap with locking arrangements of Each 1 No.
approved design to prevent foreign matter from getting into bore hole,as required,
within all leads and lifts, complete in all respects as per directions of the Engineer -
in- Charge.
11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable Mtr 250 Mtrs
material with an average specific gravity of not less than 2.5,not containing more
than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free
from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and
organic material as pe IS 4097-1967 with upto date amendments, if any, around
intake of tubewell with minium thickness of shroud around screen generally 100
mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum Hr 30 Hrs
750 CFM capacity, pumping pipe of 200 mm size and air line of minimum 65 mm
size or with other suitable method,till the well is thoroughly developed as per
clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all
respects as per direction of the Engnieer -in- Charge.

13.00 Development of tubewell by continous over pumping method,with VT pump/ Hr 20 Hrs

submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all
respects as per directions of the Engineer -in- Charge .The draw down and
discharge to be established by running the VT/ Submersible pump continuosuly for
8 hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 Job 1 Job.
with upto date amendments, if any, using plumb or plunger 6 mm smaller in dia
within the inside diameter of the well casing.The results of the verticality test shall
be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-
to-date amendments, if any, as appended with the tender documents and handed
over complete in all respect as the directions of the Engineer -in- Charge.

15.00 Dismentalling of Rig or other allied accesssories after completion of job within all Job 1 Job.
leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of Job 1 Job.
IS 2800 (Part-II) -1979 with upto date amendmentes if any, as appended with the
tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.
 DETAIL OF MEASUREMENT
NAME OF WORK:-Separate water supply schemes for village Dhuge, Loothre, Dittan, Dhilwan, Haleran,
Badewal, Bilna and Chandpur n Tehsil Haroli Distt. Una (HP) (SH: Drilling , lowering of assembly and
development of 300mtrs deep at Badewal)
S.No. Sub head and item of work. Unit. Qty.
1.00 Transportation of Rig along with allied accessories etc. complete including Job 1 Job.
errection and levelling at site, through all kinds of roads, approaches fields
errection and levelling at site, through all kinds of roads, approaches fields etc. in
all leads and lifts completed in all respects as per the directions of Engineer - in-
Charge.

2.00 Drilling of bore as per specifaction laid down in IS2800-1991 (part-I) with upto-date
amnedments,if any,with Direct Rotary Rig or combination drilling rig,Precussion Rig
starting with 650-600 mm dia M.S pipe reduced to 450-400 mm dia M.S pipe
conforming to IS 4270-2001 with up-to-date amendements,if any, in all kind of
soils, boulders, rocks, collapsible strata,sturated soils,artesian conditions including
the cost of all consumable,stores,water,fuel,lubricants and other accessories etc.
complete in all respectsd as per the directions of the Engineer -in -Charge.

2.01 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 0-30 mtrs
below ground level within all leads and lifts.
2.02 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 30-60 mtrs
below ground level within all leads and lifts.
2.03 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 30 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 60-90 mtrs
below ground level within all leads and lifts.
2.04 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 90-140 mtrs
below ground level within all leads and lifts.
2.05 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 140-190 mtrs
below ground level within all leads and lifts.
2.06 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 190-240 mtrs
below ground level within all leads and lifts.
2.07 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 50 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 240-290 mtrs
below ground level within all leads and lifts.
2.07 Drilling and lowering of M.S. Casing pipe conforming to IS 4270-2001 with up-to- Mtr 10 Mtrs
date amendments,if any, of suitable sizes as mentioned above,from 290-300 mtrs
below ground level within all leads and lifts.
3.00 Collection ,preservaion and display of suitable size sample box with top lid and Each 1 No.
locking arrangement till handing over of the tube well to the department complete
in all respects as per direction of the Engineer -in-Charge.
4.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 300 Mtr 155 Mtrs
mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.
5.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 Mtr
Cage type "V" wire wound screens of size 300 mm ,8 mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Chrage.
5.02 Providing & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe Mtr 11 Mtrs
300 mm dia nominal size housing, 8 mm thick having out side dia mtrs.323.9 mm
bevelled edges, conforming to I.S. 4270-2001 slot size 1.57x75mm welded with up-
todate amendments, if any ,about 4 mtrs to 7 mtrs in length, welded without any
circumferential joints,into bore hole in vertical position including cost of all
scaffolding derricks,poles,clamps embedded in foundation etc. including cost of all
cutting,threading and welding of pipes etc. within all leads and lifts, complete in all
respects as per the directions of the Engineer -in-Charge.

6.00 Providing and fixing M.S taper/reducer as per lengths approved by Engineer -in- Each 1 No.
Charge, the material of M.S taper/reducer shall be equivalent to parent pipe
material and shall conform to chemical composition as per clasue 5.2 and
mechanical properties as per clasue 6.1and table 1 of IS 4270-2001 with upto date
amendments,if any, complete in all respect as per directions of the Engineer -in -
Charge.

7.00 a) Supplying & Lowering of IS marked Electric Resistance Welded M.S.pipe 200 Mtr 110 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
bevelled edge conforming to I.S 4270-2001 with up-todate amendments, if
any ,about 4 mtrs to 7 mtrs in length, welded without any circumferential joints,into
bore hole in vertical position including cost of all scaffolding derricks,poles,clamps
embedded in foundation etc. including cost of all cutting,threading and welding of
pipes etc. within all leads and lifts, complete in all respects as per the directions of
the Engineer -in-Charge.

7.01 b) Supply and lowering at site Electric Resistance Welded (ERW) Stainless Steel Mtr 1 mtr
Cage type "V" wire wound screens of size 200 mm ,6.3mm thick with slot opening
1.0 mm, as per IS 8110-2000 with upto date amendments, if any, and material
specification as per AISI "American Iron and Steel Inst" Type Grade SS-304 in
suitable lenghts as per site conditions, including the cost of SS socket 8 mm
thickness of length 140 mm, confirming to AISI grade 304, suitable to accomodate
screen and ring including jointing screen with blind pipes complete in all respects
all scaffolding derricks,poles, clamps, embedding in foundation etc. including cost
of all cutting, threading and welding of pipes etc. within all leads and lifts complete
in all respects as per the directions of the Engineer - in - Charge.Screen will be of
continuous trapezoidal wire spirally wound around fabricated cage.The wrapping
wire having "V" shaped (Wedge) profile wire with flat surface on the outside and
producing expanding slots on the inside of various dimensions, resistance welded
to a cylindrical body made of number of longitudinal special high tensile support
rods to provides smooth unrestricted bore which are in turn welded into cylindrical
ring couplings on both sides of screens with in all leads and lifts complete in all
respect as per the direction of the Engineer-in-Charge.
7.02 Pdg & Lowering of IS marked Electric Resistance Welded M.S.slotted pipe 200 Mtr 22 Mtrs
mm dia nominal size housing, 6.4 mm thick having out side dia mtrs.219.10 mm
Screwed End Socketted, conforming to I.S. 4270-2001 slot size 1.57x75mm
welded with up-todate amendments, if any ,about 4 mtrs to 7 mtrs in length,
welded without any circumferential joints,into bore hole in vertical position including
cost of all scaffolding derricks,poles,clamps embedded in foundation etc. including
cost of all cutting,threading and welding of pipes etc. within all leads and lifts,
complete in all respects as per the directions of the Engineer -in-Charge.
8.00 Providing and fixing M.S cetralized guides at suitable spacing for each tube well as Each 5 Nos.
per IS 226-1991 with upto-date amendments,if any, within all leads and
lifts ,1x4Nos. completed in all respects in all respects as per the directions of the
Engineer -in-Charge.
9.00 Supplying ,lowering and fixing in position IS marked mild steel bail plug of 200 Each 1 No.
mm/300 mm diameters with "U" hooks as per IS 2800-1991 with up to date
amendements ,if any, within all leads and lifts, complete in all respects per
directions of the Engineer -in- Charge.
10.00 Providing and fixing in position threaded iron cap with locking arrangements of Each 1 No.
approved design to prevent foreign matter from getting into bore hole,as required,
within all leads and lifts, complete in all respects as per directions of the Engineer -
in- Charge.
11.00 Supplying and packing of gravel, consisting of hard quartz or other suitable Mtr 300 Mtrs
material with an average specific gravity of not less than 2.5,not containing more
than 2% by weight of thin flat of elangated pieces, shall be of sub rounded to
rounded grains with minimum angular features of size 2-3.35 mm , shall be free
from impurities such as shafe,shale,mica,felspar,clay,sand,dirt loam,baematte and
organic material as pe IS 4097-1967 with upto date amendments, if any, around
intake of tubewell with minium thickness of shroud around screen generally 100
mm to the entire depth of the bore as per 2800(Part-I ) 1991 with upto date
amendments, if any, with in all leads and lifts complete in all respects as per
direction of the Engineer -in- Charge.

12.00 Development of tubewell by back washing method,with air compressor of minimum Hr 30 Hrs
750 CFM capacity, pumping pipe of 200 mm size and air line of minimum 65 mm
size or with other suitable method,till the well is thoroughly developed as per
clause 4.2 of IS 11189 -1985, with upto date anebdnebts,if any, complete in all
respects as per direction of the Engnieer -in- Charge.

13.00 Development of tubewell by continous over pumping method,with VT pump/ Hr 20 Hrs

submersible pumps of suitable capacity not less than double the discharge
established by the compressor method/ design discharge, untill the well is sand
free as per IS-11189-1985 up -to- date amendments, if any, complete in all
respects as per directions of the Engineer -in- Charge .The draw down and
discharge to be established by running the VT/ Submersible pump continuosuly for
8 hours in the presence of officer not less than the rank of Assistant Engineer.

14.00 Testing the verticality of the tubewell as per clause 4.3 of IS 2800 (Part-II) 1979 Job 1 Job.
with upto date amendments, if any, using plumb or plunger 6 mm smaller in dia
within the inside diameter of the well casing.The results of the verticality test shall
be recorded on proforma shown in Appendix A of IS 2800 (Part-II) 1979 with up-
to-date amendments, if any, as appended with the tender documents and handed
over complete in all respect as the directions of the Engineer -in- Charge.

15.00 Dismentalling of Rig or other allied accesssories after completion of job within all Job 1 Job.
leads and lifts, complete in all respects as per the directions of the Engineer -in-
Charge.
16.00 Handing over of the tubewell in complete shape as per appendex "B" of clause 7 of Job 1 Job.
IS 2800 (Part-II) -1979 with upto date amendmentes if any, as appended with the
tender documents, in laminated form , in triplicate, complete in all respect as per
the directions of the Engineer-in-Charge.
 ANALYSIS OF RATES
Excavation in foundations, trenches etc., in earth work. lift upto 1.5 metres stacking the
excavated soil not more than 3 metres clear from the edge of the excavation and then
returning the stacked soil in 15cm. layers, when required into plinths sides of foundations etc
consolidating eac deposited layer by ramming and watering and then disposing of all surplus
excavated earth as directed within a lead of 20 metres.
PICK WORK DETAIL OF COST FOR 10 CUM
DESCRIPTION Unit Qty. Rate
Labour
Beldar Each 8.32 350.00

Bhisti Each 0.28 350.00

Total
Add for water charges @ 1.5%
Total
Add for contrctor's Profit @ 10%
Add for overhead charges @ 5%
Total

Cost for 10 cum

Cost per cum
Add 5% GST and 1% LC

Say Rs. 372.40

Executive Engineer
JS Division No. 1 Un
metres stacking the
ion and then
s of foundations etc.
posing of all surplus

T FOR 10 CUM
Amount

2912.00

98.00
3010.00
45.15
3055.15
305.52
152.76
3513.43

3513.43
351.34
21.08
372.42
only

Executive Engineer
S Division No. 1 Una
 PROFORMA FOR SPLITING UP OF WORK SANCTION THEREOF

1 Name of work : : Construction of irrigation tubewells for left out area of various villages of Haroli consituency in
Distt. Una HP (SH: Drilling of tubewells , lowering of assembly and development of Tube wells)

2 Reference of A/A & E/S with : Secretary (JSV) to GoHP letter No. IPH-B(F) 3-2/2017 dated 28-9-2021 for Rs. 1275.06 lakh
amount. only.
3 Reference of T/A with amount. : --

4 Detail of component part amount of each component as per A/A & E/S.
S. Component T/wells
No. Baliwal Lower Dharam Kangar Rora Haroli Ispur Nagnoli Pandoga Pandoga Badhera Bhadsali Saloh
Khad pur Kayarian lower
i D/L of T/well 3963773 1618773 1618773 2552845 3216588 2552845 2943543 3963773 2552845 1618773 1618733 2552845 1830188

ii C/O pump 749287 749287 749287 749287 749287 749287 749287 749287 749287 749287 749287 749287 749287
house cum
chowkidar qtr.

iii P/L of R/main 1624133 95030 4614757 397507 232019 1432837 889957 3975340 949388 1181408 727075 1334584 282448
iv 930000 300000 500000 690000 740000 825000 740000 975000 735000 300000 250000 690000 300000
S/E of P/mach.
v P/L of 1862254 947494 4248444 1013732 893875 1094362 782223 2665867 1452846 1445288 3894632 813716 1390853
Distribution
vi C/O Delivery 33108 33108 33108 33108 33108 33108 33108 33108 33108 33108 33108 33108 33108
Tank
vii C/O outlets 148550 133695 326810 282245 207970 148550 133695 163405 178260 148550 148550 133695 133695

viii C/O Boundary 236650 236650 236650 236650 236650 236650 236650 236650 256650 236650 236650 236650 236650
wall

ix C/O collection 543120 0 0 543120 543120 543120 543120 543120 543120 0 0 543120 0
tank
x Internal wiring 38466 38466 38466 38466 38466 38466 38466 38466 38466 38466 38466 38466 38466
of pump
house.
xi Provision for 1335680 1043000 1344860 1451920 1764620 1137320 1509120 1478680 1432550 1099275 1326250 1182540 2078270
SOP.
Total 11465021 5195503 13711155 7988880 8655743 8791565 8599169 14822696 8901520 6850805 9022791 8308011 7072965
Total 119385824.00
Add 3% contingency charges except SOP amount i.e. on Rs. 101501679.00 3045050.00
Add 5% escalation charges except SOP amount i.e. on Rs. 101501679.00 5075084.00
G.Total 127505958.00
1275.06 lakh
5 In case technical sanction has : working estimate for drilling , lowering and development of tubewells has been framed. The
not been accorded reason technical approval for balance components shall be takenup only after ascertain the discharge
thereof and the probable date of tubewell.
by which it is likely to be
accorded.

6 Whether spliting up drawn : No, any splitup sanction accorded previousely.

previously if sanction number &
date with amount in each case
and component as a whole.

7 Upto date expenditure for each : --NIL--

component .

8 The component for which : Drilling of tubewell , Lowering of assembly and development of 13 Nos. tubewells amounting to
sanction of spliting is required Rs.3,33,45,800 only
alongwith estimated cost of
component work.

9 The working estimate only : --

checked by EE/SE should
accompany the proposal for
spliting up of the work

10 Budget allotment during the : There is a budget provision to the tune of Rs 79.12 lakh during the current financial year under
year 2021-22 T/wells demand No. 32 vide Chief Engineer Jalshakti Vibhag Hamirpur office letter No. 9924
dated 10-8-2021

11 Detail reason necessiteting the : The A/A & E/S of the scheme accorded recently. First of all the working estimate for D/L of
sanction for spliting up of the tubewells has been prepared and after the development of tubewell, the working estimates for
work. balance components shall be prepared.

12 In the event expenditure over : Not yet required.

A/A&E/S (incurred) beyond
permissible limit the position of
the revised estimate.

Executive Engineer,
Jalshakti Division No I Una.