Scribd
Upload
5 views

cib1262

The document outlines the diagnostic trouble code (DTC) B1262, which indicates a communication failure between the A/C control assembly and the gateway ECU lasting over 10 seconds. It includes inspection procedures to check the A/C switch operation, wire harness integrity, and communication line resistance, with specific voltage and resistance standards provided. Depending on the results of these checks, it suggests either replacing the A/C control assembly or repairing the wire harness and connectors.

Uploaded by

Maurice
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
5 views

cib1262

The document outlines the diagnostic trouble code (DTC) B1262, which indicates a communication failure between the A/C control assembly and the gateway ECU lasting over 10 seconds. It includes inspection procedures to check the A/C switch operation, wire harness integrity, and communication line resistance, with specific voltage and resistance standards provided. Depending on the results of these checks, it suggests either replacing the A/C control assembly or repairing the wire harness and connectors.

Uploaded by

Maurice
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

05–2585

DIAGNOSTICS – MULTIPLEX COMMUNICATION SYSTEM 05J68–01

DTC B1262 A/C ECU COMMUNICATION STOP

CIRCUIT DESCRIPTION
This DTC is detected when communication between the A/C control assy (A/C ECU) and gateway ECU stops
for more than 10 seconds.
DTC No. DTC Detection Condition Trouble Area

 A/C control assy


B1262 A/C ECU communication
i ti stops
t
 Wire harness

WIRING DIAGRAM
G1 A8
Gateway ECU Center Connector No. 2 A/C Control Assy

Instrument 4 13
GR B
Panel J/B Assy MPD2 5C 5J MPX+
12 3

Body ECU

9 8 8
GR GR
MPX1 1G 5K 5J MPX2+
17 11

J19
J/C 10 3
Y Y Y
5K 5J +B
D D 6

5 1K

Instrument GND
ECU–B 1
Panel J/B Assy

Engine Room J/B


1 1B
1 1
W DC/DC
3D 3M
2 1 W–B
F15
FL Block Assy B
MAIN 1
B
BE1
1

Battery
IJ

B79858

2004 Prius – Preliminary Release (RM1075U)

Author: Date: 2749


05–2586
DIAGNOSTICS – MULTIPLEX COMMUNICATION SYSTEM

INSPECTION PROCEDURE
1 CHECK OPERATION

(a) Check that the A/C switch can operate the air conditioner normally.
OK: A/C switch can operate the air conditioner normally.
NG Go to step 2

OK

REPLACE A/C CONTROL ASSY

2 CHECK WIRE HARNESS (A/C CONTROL ASSY – BODY GROUND)

Wire Harness Side (a) Disconnect the A8 ECU connector.


A8 (b) Measure the resistance and voltage of the wire harness
A/C Control Assy (A/C ECU) side connector.
Standard:
Tester Connection Condition Specified Condition
A8–6 (+B) – Body ground Constant 10 to 14 V
A8–1 (GND) –
Constant Below 1 Ω
+B Body ground
GND
B79990 NG REPAIR OR REPLACE HARNESS AND
CONNECTOR

OK

2004 Prius – Preliminary Release (RM1075U)

Author: Date: 2750


05–2587
DIAGNOSTICS – MULTIPLEX COMMUNICATION SYSTEM

3 CHECK RESISTANCE OF COMMUNICATION LINE

(a) Disconnect the A8 and G1 ECU connectors.


Wire Harness Side
(b) Disconnect the 1G J/B connector.
A8 (c) Measure the resistance of the wire harness side connec-
A/C Control Assy (A/C ECU) tors.
Standard:
Tester Connection Specified Condition
A8–3 (MPX+) – G1–12 (MPD2) Below 1 Ω
A8–11 (MPX2+) – 1G–9 (MPX1) Below 1 Ω

Result:
Result Proceed to
MPX+ MPX2+ Both are OK A
One is OK B
G1
Both are NG C
Gateway ECU

MPD2

1G
Instrument Panel J/B Assy

B REPLACE A/C CONTROL ASSY AND REPAIR


OR REPLACE HARNESS AND CONNECTOR

MPX1
B79860 C REPAIR OR REPLACE HARNESS AND
CONNECTOR

REPLACE A/C CONTROL ASSY

2004 Prius – Preliminary Release (RM1075U)

Author: Date: 2751

You might also like