Motor Grader

BG 190 T-4 (6x4) / BG 190 TA-4 (6x6)

www.hbm-nobas.de
 HP-Cab. 3370
LP-Cab. 3150
2638 1542
6136
8737 2490
9583 2670
9419
10266 Dimensions in mm
max. width over tyres
with standard tyres

Speeds
Engine Data (all wheel drive and rear axle drive systems)
Make/Model CUMMINS/diesel engine Forwardkm/h
Typ 4 cycle, direct injection, turbo charged, water-cooled, 1.3.8
Rated ned horsepower (SAE J1995) at 2200 rpm 129 kW/176 HP 2.6.6
 at 2000 rpm 133 kW/181 HP 3.8.8
No. of cylinders in line 6 4.15.4
Bore & stroke 107 x 124 mm 5.25.0
Displacement 6.7 litres 6.40.0
Reverse
Engine equiped with a dual element, dry-type air cleaner with dust 1.3.8
ejector. 24 volt starting and electrical system. 70 amp alternator and 2.8.8
24 volt starter with 3,7 kW (5,0 HP). 3.19.4
2 batteries 74 Ah each. Acoustic back up alarm in reverse driving.

Rear Axle
Operating Weight
Oscillating tandem axle with axle insert.
Total weight approx. 19000 kg No-Spin differential.
On rear wheels approx. 13300 kg Multi-disc brakes in all four wheel hubs.
On front wheels approx. 5700 kg Parking brake at powershift transmission.

Weights shown include cab, all operating fluids, HD rear ripper, front
dozer blade.

Tandems
Drive via roller chains.
All Wheel Drive System Torsion-proof box sections.
Height 550 mm
Hydrodynamic rear axle drive with 6-speed Ergopower transmission Width 184 mm
and torque converter as well as freely selectable microprocessor con- Thickness of walls 20 mm
trolled hydrostatic front axle drive. Power train is controlled appropri- Wheel base 1542 mm
ate to tyre traction of front and rear wheels. Oscillation±15°
Ground clearance 480 mm

Rear Axle Drive System Wheels & Tyres

Hydrodynamic rear axle drive with 6-speed Ergopower transmission Tyre size 17.5 R25 radial
(make ZF 6 WG) and torque converter. Rim size 14.00 x 25/1.3

www.hbm-nobas.de
 Brakes Drawbar
Service brake Y-shaped fully welded construction.
Dual-circuit, power-boosted, multi-disc oil-bath type, effective on four Dimensions (solid sections) 40 x 210 mm
wheels. Includes reserve power and operator warning system
Parking brake
Independent electrically operated, acting on power shift.
Hydraulic spring accumulated single disc type. Moldboard (standard)
Moldboard (12 ft) 3660 x 660 x 20 mm (12’ x 26,0’’ x 0,8’’)
Front Axle Blade material High carbon steel
Blade pull at a friction factor of 0.8 BG 190 T-4 96 kN
2 types are available BG 190 TA-4 121 kN
Oscillation 15° up and down
Steering angle 45°
Wheel lean ±17° Blade Range
Ground clearance 591 mm
Reach outside tyres without articulation (RH&LH)
Non driven with wheel lean (T version)  2485 / 1920 mm
Stable welded steel beam with wheel lean Reach outside tyres with articulation (RH&LH) blade resting on
Driven with wheel lean (TA version) levelled surface 3335 / 2770 mm
Stable welded steel beam with wheel lean and radial piston Blade side shift 1250 mm
engines in wheel hubs, pulling pover on surface conditions. Blade tilt range 31°- 74°
Electronically adjustable (infinitely variable), possibility to fit in the Bank sloping angle (RH&LH) 90°
hydraulic differential lock. Lift above ground 470 mm
Cut below ground 430 mm
Distance blade / front axle 2632 mm
Steering
All blade movements and positions can be controlled from the
Hydraulic power steering. operator´s seat.

Minimum turning radius without dozer blade 7500 mm

Minimum turning radius with dozer blade 8050 mm
Steering angle 45°
Operator’s Platform
Dimensions
Frame Widht 1150 mm
Depth 1400 mm
Front and rear frame sections connected with an adjustment free
articulated pin.
Available with various options as listed under “Optional equipment“,
Front: Fully welded box section moldboard control acc. to EURO standard.
Minimum dimensions of box section 300 x 310 mm
Plate thickness 20 mm
Rear: Fully welded section
Dimensions (solid main bars) 270 x 90 mm Capacities
Hydraulic articulated frame steering (left & right) 30° Fuel 386.0 litres
Hydraulic oil 170.0 litres
Engine oil 18.0 litres
Circle (open version) Ergopower transmission 34.0 litres
Axle drive, rear 13.5 litres
Hardened teeth, cut on inside of circle for maximum strenght and Planetary gears and brakes 16.0 litres
minimum wear. The circle is held positively in place at four points by Tandem (2 x 21 litres) 42.0 litres
four clamps and guide shoes. The clamp and guide shoes are located Circle drive 9.0 litres
where greatest loading occurs. Coolant 33.0 litres
Diameter 1510 mm
Thickness 40 mm
Height 110 mm
Adjustable shoes and clamps 4

Light Equipment
Circle Drive
2 head lights at the front, every 2 indicator lights (including hazard warning
Hydraulically driven worm gear transmission. Circle drive system fully lights) at the front and rear, 2 rear lights, 2 brake lights, 1 backup light
protected against impact damage by an overload clutch. plus every 2 working lights at the top and bottom at the front of the cab, 2
Rotation360° working lights at the top at the rear of the cab, and 2 tail lights on the sides.

www.hbm-nobas.de
 Moldboard (14 ft) 4267 x 660 x 20 mm (14’ x 26,0’’ x 0,8’’)
Load-Sensing Hydraulics Cover plate for upper guide rail of moldboard
Adjustable moldboard corner shoes, left or right
The control valves of the working hydraulics may be actuated at a Moldboard extension, left or right (1 ft) 305 mm
Float position for both moldboard lift cylinders
time and independent of each other. The load-sensing pump (axial
Electric fuel pump with automatic switch-off
piston pump) discharges only the required quantity of oil if a control
Towing device, tiltable
valve is actuated. When hydraulic power is not required system pres-
sure is only 24 bar and ensures low oil temperature und fuel saving. Wheels and tyres
Tyre size 14.00 x 24 diagonal
Lock valves and brake valves prevent a cylinder drift under load. Rim size 10.00 x 24
Operating pressure 184 bar Tyre size 17.5-25 diagonal
Oil flow, max. 99l/min Rim size 14.00 x 25/1.3
 Other types on request.
Front dozer blade with position indicator, parallel guided
Optional Equipment Width / Height  2490 x 780 mm
Cut below ground  170 mm
Cab, standard, tiltable Lift above ground  505 mm
Integrated ROPS/FOPS cab mounted on isolators to limit vibration Weight  865 kg
and noise entering the cab. Excellent all-round visibility. Roomy and V-scarifier between front axle and moldboard, 11 teeth
comfortable. Adjustable steering pedestal with EURO control lever Ripping width  1310 mm
arrangement. Interior of cab fully lined, floor covering. Tined safety Ripping depth  240 mm
glass windows, sliding doors left and right with lockable intermediate
Lift above ground  300 mm
positions, fresh air heating with pre-filter, air circulation. Adjustable,
Weight  850 kg
mechanical spring mounted driver’s seat with safety belt. One inside
mirror and two folding outside mirrors. Rear ripper with depth indicator, medium heavy, 4 teeth (max. 7)
Front window washer. Ripping width  2120 mm
Wipers front and rear. Ripping depth  420 mm
Blinds front and rear. Lift above ground  560 mm
Weight  804 kg
Height / Width / Depth 1980 / 1470 / 1700 mm
Heavy-duty rear ripper with depth indicator, 6 teeth
Cab, low-profile, tiltable
Ripping width  2120 mm
Height / Width / Depth 1760 / 1470 / 1700 mm
Ripping depth  270 mm
NAIS control panel (rods) Lift above ground  570 mm
EP control panel (Joystick controls) Weight  1529 kg
Air-condition for cab Push-Pull block, in front 926 kg
Heatable rear view mirrors
Front dozer blade, articulated
Auxilliary heating
Beacon (orange) Mudguards  on front wheels
Air-cushioned driver’s seat Mudguards  on rear wheels
Recording speedometer Protective cover for powershift transmission
Biological Oil in hydraulic system
Cooling box
Articulation angle indicator
Stereo radio with CD-player
Fuel tank pump with automatic switch-off
Sliding side windows Special paint
Protective grids for lights and cabin Ergopower transmission with torque converter and lock-up clutch
Circle (closed version) Tool kit, wheel chocks, warning triangle, fire extinguisher,
Hardened teeth, machine-cut on inside of circle for maximum first aid kit etc.
strength and maximum wear. The circle is held positively in place by Automatic blade control
an adjustment-free roller bearing. Various 2D / 3D / GPS systems
Circle diameter 1510 mm
CE certificate
Tool width 83 mm
Height 130 mm Speed limitation at 20 km/h possible

GP Papenburg Maschinenbau GmbH

Rothenburgstraße 20 · 99734 Nordhausen · Germany
Tel: ++49 (0) 3631 695-125 · Fax: ++49 (0) 3631 695-121
Edition 04/16
E-Mail: [email protected] · [email protected] Technical data are subject
www.gp.ag/hbm-nobas/Start/ to alteration.

www.hbm-nobas.de