DATA SHEET FOR

BASIC DESIGN DOC. NO. 504 Pneu. On-off Actuator REV. 1 OF3
1 ADMINISTRATIVE IDENTIFICATIONS 67 SERVICE IDENTIFICATIONS continued
2 Tag number 68 Explosion proof code IEC
3 Contract NO. 69 Hazardous area class II Div / Zone 2
4 Project 70 Hazardous area group B Temp class T4
5 Area 71 Enviromental area outdoor
6 Unit name 72
7 73
8 74
9 75
10 SERVICE IDENTIFICATIONS 76
11 Equipment 77 COMPONENT DESIGN CRITERIA
12 Service 78 Criticality Normal
13 PID / Reference dwg number 79 Seat leakage TSO(Y/N) ANSI V
14 Upstream line number 80 *Maximum stem leakage rate NA
15 Upstream nominal line size 81 Partial stroke testing NA
16 NA NA 82 SIL Requirement
17 Upstream wall thickness 83 Maximum allowable SPL 85 dBA
18 Upstream pipe material 84 *Actuator sizing factor 1.5
19 Fluid service 85 Supply pressure medium instrument air
20 Upstream line orientation 86 Minimum supply press 0.3 MPa gage
21 Downstream line number 87 Maximum supply press 0.9 MPa gage
22 Downstream nominal line size 88 Certification
23 89 Test requirements hydrostatic pressure test
24 Downstream wall thickness 90 Failure action (supply loss) Close
25 Downstream pipe material 91 Signal loss failure mode fail closed
26 92 *Full stroke time
27 PROCESS VARIABLES MATERIAL FLOW CONDITIONS
28 Case Minimum Normal Maximum Units
29 Fluid state Liquid NA
30 Fluid phase Single phase NA
31 Fluid name NA
32 Max. allowable pressure drop MPa
33 Upstream gage pressure MPa gage
34 Downstream gage pressure MPa gage
35 Temperature °C
36 Viscosity NA cP
NA
37 Density kg/m3
38 NA
39 NA
40 NA
41 NA
42 NA
43 NA
44 NA
45 NA
46 NA
47 NA
48 NA
49 NA
50 NA
51 NA
52 NA
53 NA
54 NA
55 NA
56 NA
57 PROCESS DESIGN CONDITIONS 93 PROCESS DESIGN CONDITIONS Continued
58 Design gage pressure min MPa gage 94 Barometric absolute pressure
59 Design gage pressure max MPa gage 95 NA
60 Design temperature minimum °C 96 Ambient temperature min ℃ Max(solar) ℃
61 Design temperature maximum °C 97
62 Max shut-off press differential MPa 98 MATERIAL PROPERTIES
63 NA 99 Critical temperature
64 NA 100 NFPA health hazard Flammability
65 Base absolute pressure 101325
NA Pa abs 101 NFPA Reactivity Corrosive
66 Base Temperature NA
15.6 °C 102 Erosive Toxic
67
68
 DATA SHEET FOR

BASIC DESIGN DOC. NO. 504 Pneu. On-off Actuator REV. 2 OF3
1 VALVE BODY AND BONNET 66 TRANSDUCER/POSITIONER OR CONTROLLER
2 *Body type ball 67 Tag No. NA
3 *Body size Rating cl 300 68 Configuration type NA
4 *Body style 69 Input signal type NA
5 *Bonnet style 70 Output signal type NA
6 *Inlet connection nominal size Rating cl 300 71 Accuracy rating NA
7 *Outlet connection nominal size Rating cl 300 72 Mounting location / type NA
8 End connection termination type flanged Style RF 73 Loop power supply NA
9 Flange facing finish ANSI B 16.5 74 Enclosure type number / class NA
10 *Shaft seal type 75 Digital communication standard NA
11 Face-to-face standard ANSI B16.10 (short) 76 Type of protection NA Class NA
12 *Yoke boss diameter 77 Pressure gauges NA
13 *Body and bonnet material 78 By-pass manifold NA
14 *Lining material 79 Enclosure material NA
15 *Body / Bonnet bolting material 80 Elec. connection NA QTY. NA
16 *Packing flange bolting material 81
17 *Gasket material 82
18 *Packing material 83
19 84
20 85
21 86 PERFORMANCE CHARACTERISTICS
22 87 *Max pressure at design temp MPa gage
23 88 *Maximum design temperature °C
24 89 *Minimum working temperature °C Max K
25 90 *Maximum pressure drop
26 VALVE TRIM 91 *Rated flow coefficient type Coef Xt
27 Closure member type full ball 92 *Rated factor FL Style Fd
28 *Trim style full port 93 *Rated seat leakage class
29 *Size 94
30 *Rated travel mm 95 ACCESSORIES
31 Inherent characteristic NA 96 Supply power medium set/filter air filter
32 *Seal ring type 97 Supply power medium gauges
33 *Flow direction force NA 98 *Tubing nominal size
34 *Balanced/Unbalanced 99 *Tubing and fitting material
35 *Shaft diameter mm 100 Supply medium connection 1/2"(NPT)
36 *Closure member material 101 *Position indicator
37 *Seal ring material 102 *Volume tank
38 *Shaft material 103 *Grounding connection
39 *Flow ring material 104 *Dust excluder
40 *Guide / Retainer material 105 *Quick exhaust device
41 *Guide bushing material 106 *Port protector
42 *Hard facing / coating 107 PST kit
43 108
44 109
45 110 SPECIAL REQUIREMENTS
46 111 Custom tag sst permanent attached
47 112 Reference specification
48 113 Special preparation NA
49 ACTUATOR 114 Compliance standard NA
50 Actuator type pneumatic piston 115 Construction code NA
51 Acting style single acting, spring return 116 Software configuration NA
52 Control mode on-off 117
53 *Effective area 118
54 *Bench set Lower range-limit 119
55 *Bench set Upper range-limit 120
56 *Max. allowable press. 121 PURCHASE
57 *Min. required press. 122 Purchase order number NA
58 Handwheel type / position side mounted,continuous 123 Item number NA
59 *Mounting orientation 124 *Serial number
60 *Casing / cylinder material 125 *Dry weight
61 *Diaphragm / O ring material 126 *Manufacturer reference dwg
62 *Yoke material 127
63 *Supply medium consumption 128
64 *Certification 129
65 PST style NA 130
131 *COMPONENT IDENTIFICATIONS
132 *COMPONENT TYPE *MANUFACTURER *MODEL NUMBER
133
 DATA SHEET FOR

BASIC DESIGN DOC. NO. 504 Pneu. On-off Actuator REV. 3 OF3
1 POSITION SWITCHES 51 POSITION TRANSMITTER (CONTINUED)
2 Tag No. Hold QTY. 2 52 Integral indicator style NA
3 Housing type explosion proof enclosure 53 Signal termination type NA
4 Sensor style mechanical micro switch 54 Type of Protection NA Class NA
5 Output signal type dry contact 55 *Mounting location / type NA
6 56 *Enclosure material NA
7 *Contacts Rating A At 24 Vdc 57 Elec. connection NA QTY. NA
8 Contacts arrangement SPDT 58 SUPPLY PRESSURE TRIP VALVE
9 Enclosure type no / class IP 65 59 Configuration type NA
10 *Integral indicator style 60 Volume tank size NA
11 Signal termination type 61 Trip set pressure reset NA
12 Type of Protection flameproof Class dⅡBT4 62 Tank max working pressure NA
13 *Mounting location / type 63 Minimum supply capability NA
14 *Enclosure material 316 SST 64 Maximum supply capability NA
15 *Shaft material 65 Trip set pressure LRL NA
16 *Bushing material 66 Trip set pressure URL NA
17 *Fastener material 67 Tank construction code NA
18 *Gasket / O ring material 68 *Mounting location / type NA
19 Elec. connection M20*1.5(F) QTY. 2 69 *Body material NA
20 SOLENOID OR PILOT VALVE 70 *Diaphragm / O ring material NA
21 Tag No. Hold QTY. 1 71
22 Body type 3 way quick exhaust 72 line_text_072
EMISSIONS MONITOR SWITCH
23 *Inlet connection nominal size 1/2 in Style NPT(F) 73 Sensor type NA
24 *Coil type low power watt rating W 74 Housing type NA
25 Enclosure style explosion proof enclosure 75 Inlet conn nominal size NA Style NA
26 Coil insulation class H 76 Output signal type NA
27 *Min operating press differential MPa Max MPa 77 Enclosure type no / class NA
28 Enclosure type no / class IP65 78 Contacts AC rating NA At max NA
29 Signal power source line 24 V(dc) 79 Contacts DC rating NA At max NA
30 Manual operator type NA 80 Contacts arrangement NA
31 Type of actuation direct acting 81 Integral indicator style NA
32 *Press port orifice size Exhaust port 82 Signal termination type NA
33 Operation style normally closed 83 Type of Protection NA Class NA
34 Signal termination type screw terminals 84 *Mounting location/type NA
35 Type of Protection flameproof Class dⅡBT4 85 *Enclosure material NA
36 Mounting location / type body connections 86 *Diaphragm material NA
37 *Enclosure material 316 SST 87
38 *Body material 316 SST 88
39 *Seat / Disc / Diaphragm matl 89 line_text_089 BOOSTER RELAY
40 Certification/Test by-pass NA 90 Configuration type NA
41 Elec. connection M20*1.5(F) QTY. 1 91 End connection nominal size NA Style NA
42 POSITION TRANSMITTER 92 *Dead band rating NA
43 Tag No. NA 93 *Maximum supply capability NA
44 Housing type NA 94 *Supply port size NA Exh port NA
45 Sensor style NA 95 *Body material NA
46 Accuracy / Linearity rating 96 *Closure member material NA
47 Output signal type NA 97 *Diaphragm material NA
48 Enclosure type no / class NA 98 *Test conn material NA
49 Digital communication standard NA 99 *Gasket / O ring material NA
50 Signal power source NA 100
101 Note:
102 1.Information with asterisk(*) shall be confirmed or supplied by manufacturer according to the service condition during bidding.
103 2. Key fluid components: N/A
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
 STAGE BID

PROJECT DOC. NO. SIPD-1561-INT-DS-0504

PAGE NO.

DOCUMENT NAME Typical Datasheet for Pneumatic ON/OFF Actuator

Attachment list for Pneumatic ON/OFF Actuator

Valve Body and Bonnet Valve Trim Quantity

Item CPF2 Area Name P&ID Valve Size Piping Class Valve Pressue Rating Buyer Remark
Material Material Outside skid

Oil Process
1 Inlet Manifold 1101 - - - - - -
- - - - - -
1102 - - - - - -
- - - - - -
2 1st-Stage Seperator
- - - - - -
1103 - - - - - -
- - - - - -
Oil Oil Heat Exchanger 1104 - - - - - -
3
Skid 1105 - - - - - -
Medium-Oil Heat 1106 - - - - - -
4
Exchanger Skid 1107 - - - - - -
- - - - - -
1108 - - - - - -
- - - - - -
5 2nd-Stage Seperator Skid
- - - - - -
1109 - - - - - -
- - - - - -
6 Dehydration Pump A/B 1110~1111 - - - - - -
Electrostatic Dehydrator
7 1112~1113 - - - - - -
A/B
8 Electrostatic Desalter A/B 1114~1115 - - - - - -

9 Recycle Pumps A/B 1116~1117 - - - - - -

- - - - - -
1118 - - - - - -
- - - - - -
10 H2S Re el Tower
- - - - - -
1119 - - - - - -
- - - - - -
11 BOOSTER PUMPS 1120~1121 - - - - - -
12 Air Cooler Skid 1122 - - - - - -

Oil Storge Tank (T- - - - - - -

13 1124
32110A/B)
- - - - - -
Off-Spec Oil Tank (T- - - - - - -
14 1125
32120) - - - - - -
Feed Pump (P-
15 1126 - - - - - -
32210A/B/C)
Export Pump (P-
16 1127 - - - - - -
32220A/B/C)
Water Draw-off Pumps
17 1129 - - - - - -
(P-32130A/B)
Off-Spec Oil Pumps
18 1130 - - - - - -
(P-32140A/B)
Medium-Oil Water Heat - - - - - -
19 1131~1132
Exchanger Skid - - - - - -

20 Diesel Supply System 1133 - - - - - -

21 Anti-Foam Fnjection Skid 1134 - - - - - -

22 Demulsifier Injection Skid 1135 - - - - - -

Corrosionl Inhibitor
23 1136 - - - - - -
Injection Skid
Scale Inhibitor Injection
24 1137 - - - - - -
Skid
25 Open drain System 1140 - - - - - -
26 Closed Drain System 1141 - - - - - -
Custody Transfer
27 Metering Skid（SK- 1142 - - - - - -
32250）
Volume Pipe Proving Skid
28 1143 - - - - - -
（SK-32257）
Water Proving Skid（SK-
29 1144 - - - - - -
32259）
Automatic Sampling Skid
30 1145 - - - - - -
（SK-32258）
Heat Medium Heater Skid
31 1401~1404 - - - - - -
(SK-25630A~D)
Heat Medium
32 Accumulator Skid (SK- 1405 - - - - - -
25620)
Heat Medium Storage
33 1406 - - - - - -
Tank Skid (SK-25610)
Heat Medium Make Up
34 1407 - - - - - -
Pump Skid (SK-25650)

Heat Medium Circulation

35 1408 - - - - - -
Pump Skid (SK-25640)
Heat Medium Circulation
36 1409 - - - - - -
Filter Skid (SK-25660)
Daily Diesel Tank Skid
37 1410 - - - - - -
(Sk-25670)
Gas Process
MP Gas Air Cooler (E-
1 0201 - - - - - -
32620)
MP Gas Separator (V- - - - - - -
2 0202
32630) - - - - - -
MP Gas Compressor 0203 - - - - - -
3
Package (PK-33610A) 0204 - - - - - -
LP Gas Air Cooler (E-
4 0205 - - - - - -
33510)
LP Gas Separator (V- - - - - - -
5 0206
 STAGE BID

PROJECT DOC. NO. SIPD-1561-INT-DS-0504

PAGE NO.

DOCUMENT NAME Typical Datasheet for Pneumatic ON/OFF Actuator

Attachment list for Pneumatic ON/OFF Actuator

Valve Body and Bonnet Valve Trim Quantity

Item CPF2 Area Name P&ID Valve Size Piping Class Valve Pressue Rating Buyer Remark
Material Material Outside skid
5 0206
32670) - - - - - -
LP Gas Separator
6 Condensate Pump (P- 0207 - - - - - -
32680A&B)
LP Gas Compressor
7 0208 - - - - - -
Package (PK-33520A)
Condensate Separator
8 0209 - - - - - -
(V-32650)
Condensate Pump (P-
9 0210 - - - - - -
32660AB)
10 Raw Gas Export Manifold 0212 - - - - - -

LP Fuel Gas Scrubber (V-

11 0213 2" Class 150 Class 150 A105N+3mmCA A182 F316L 1 CPECC NOTE1
33910)

12 HP Flare Header 0214 4" Class 150 Class 150 A105N+3mmCA A182 F316L 1 CPECC NOTE1

HP Flare Knock-out Drum

13 0215 - - - - - -
(V-33810A)
HP Flare Knock-out Drum
14 0216 - - - - - -
(V-33810B)
15 LP Flare Header 0217 4" Class 150 Class 150 A105N+3mmCA A182 F316L 1 CPECC NOTE1
LP Flare Knock-out Drum
16 0218 - - - - - -
(V-33840A)
LP Flare Knock-out Drum
17 0219 - - - - - -
(V-33840B)
HP& LP Flare Package
18 0220 - - - - - -
(PK-33830) I
HP& LP Flare Package
19 0221 - - - - - -
(PK-33830) II
Instrument Air Skid (SK-
20 0222 - - - - - -
35210)
Utility Air Receiver (V-
21 0223 - - - - - -
35410)
Instrument Air Receiver
22 0224 - - - - - -
(V-35310)
Nitrogen Generator Skid
23 0227 - - - - - -
(SK-36110)
Nitrogen Receiver (V-
24 0228 - - - - - -
36170AB)
Gas Corrosion Inhibitor
25 0229 - - - - - -
Injection Skid (SK-31680)
26 Fuel Gas Sweetening Unit 0071 - - - - - -

Water Process
1 Buffer tank(T-30100) 1301 - - - - - -
Booster pump(P-
2 1302 - - - - - -
30100A~C)
CPI separator skid(SK-
3 1303 - - - - - -
30100AB)

4 Disposal tank(T-30110) 1304 - - - - - -

5 Feed pump(P-30210A~C) 1305 - - - - - -

Disposal pump(P-
6 1306 - - - - - -
30110A~C)
7 Oil sump tank(T-30120) 1307 - - - - - -
Oil sump pump(P-
8 1308 - - - - - -
30120AB)
Evaporation pond(D-
9 1309 - - - - - -
30100)
Raw water storage
10 1320 10" Class 150 Class 150 A105N+3mmCA A182 F6a 1 PEG NOTE3
tank(T-30140)
Raw water booster
11 1321 - - - - - -
pump(P-30140AB)
PURIFICATION
12 1322 - - - - - -
EQUIPMENT
TREATED WATER
13 1323 - - - - - -
STORAGE TANK

14 SLUDGE TANK 1324 - - - - - -

15 SLUDGE PUMP 1325 - - - - - -

SLUDGE TREATMENT
16 1326 - - - - - -
EQUIPMENT
SERVICE WATER
17 1327 - - - - - -
SUPPLY PUMP
DOMESTIC WATER
18 1328 - - - - - -
SUPPLY PUMP
Water softening skid(SK-
19 1329 - - - - - -
30140)
Water-water heat
20 1330 - - - - - -
exchanger(E-30100AB)
Vacuum deaerator
21 1331 - - - - - -
package(PK-30100)
Bottom pump(P-
22 1332 - - - - - -
30180AB)
23 RO Package(PK-30110) 1333 - - - - - -
Pneumatic Water Supply
24 1334 - - - - - -
Skid (SK-30150)
Return Water Tank(T-
25 30170) and Pump(P- 1335 - - - - - -
30190AB)
Waste water tank(T-
26 1336 - - - - - -
30180)
Waste water pump(P-
27 1337 - - - - - -
30200AB)
Fire Water Tanks(T-
28 0001 6" Class 150 Class 150 A105N+3mmCA A182 F6a 2 CPECC NOTE3
37010AB)
29 Fire Pumps 0002 - - - - - -
Firewater Loop
30 0003 - - - - - -
Distribution
 STAGE BID

PROJECT DOC. NO. SIPD-1561-INT-DS-0504

PAGE NO.

DOCUMENT NAME Typical Datasheet for Pneumatic ON/OFF Actuator

Attachment list for Pneumatic ON/OFF Actuator

Valve Body and Bonnet Valve Trim Quantity

Item CPF2 Area Name P&ID Valve Size Piping Class Valve Pressue Rating Buyer Remark
Material Material Outside skid

Foam Solution 4" Class 150 Class 150 A105N+3mmCA A182 F6a 1 CPECC NOTE3
31 0004
Distribution
8" Class 150 Class 150 A105N+3mmCA A182 F6a 3 CPECC NOTE3
Foam Proportioning Unit
32 0005 - - - - - -
Skid(SK-37130)
33 Chemical Injection Skid 1338~1344 - - - - - -

Summary 10
Note:
1. Ball: A182 F316L, Stem: A182 F316L; Seat: A182 F316L+RPTFE; other internals: SS316L; Gasket: SS316L+graphite/PTFE; Bolt/Nut: A193 B7M/A194 2HM+ Hot dipped glavnized (HDG); NACE MR0175: Required.
All wetted parts meet the related requirements of NACE MR0175/ISO 15156.

2. Ball: A182 F51; Stem: A182 F51; Seat: A182 F51+RPTFE; other internals: S31803; Gasket: S31803+graphite/PTFE; Bolt/Nut: A193 B7/A194 2H+ XLYAN Fluoropolymer Coated.

3. Ball: A182 F6a; Stem: A182 F6a; Seat: A182 F6a+RPTFE; other internals: 13%Cr; Gasket: SS316L+graphite/PTFE; Bolt/Nut: A193 B7/A194 2H+ Hot dipped glavnized (HDG).