Technical Data Sheet

Energrease LS-EP 00
Semi-fluid Gear Grease
Description
Energrease LS-EP 00 is a high-quality, lithium-based grease, incorporating solvent-refined oils. It contains an anti-wear
additive, oxidation and corrosion inhibitors, which help to ensure long service life of the grease and a high level of protection
for metal surfaces.

Application
Energrease LS-EP 00 has been designed for the lubrication of gearboxes and geared motors that require a semi-fluid grease,
as well as for plain bearings rolling bearings and sliding surfaces. This grease forms a resilient lubricating film able to
withstand high pressures at high temperatures and high rotating speeds. The EP properties of this grease ensure minimum
mechanical wear, and, together with its water-resistance and anti-corrosion capacity, lead to a high level of equipment protection.
In gearboxes and geared motors this grease ensures effective sealing, reduced noise levels and provides during shut-down,
a thick film of lubricant to inhibit corrosion and prevent 'dry' start-up.
When used in centralized lubrication systems, Energrease LS-EP 00 shows very good flow and de-compression properties,
yielding excellent performance, even in long pipelines and at very low temperature levels. Gearboxes and geared motors can
be found in a variety of applications and industries. The operating temperatures range from -35 °C to 120 °C.

Main Performance Features

• Reduced leakage and reduced noise level.
• Excellent equipment protection.
• Long service life.
• Wide operating temperature range.
• Excellent pumpability, even at very low temperatures.

Packaging and Storage

Supplied in packs of approximately 18 kg pails and 180 kg drums. Note the actual pack size may vary according to country of
supply.
Where outdoor storage is unavoidable, packs should be covered.
Ensure packs are tightly resealed after use and that they have not been contaminated in any way.

Page 1 of 2
 Typical Characteristics
Unit Test Method LS-EP 00
Thickener type - Li soap
NLGI Classification - ISO 2137 / ASTM D217 00/000
Texture - Visual Smooth
Colour - Visual Light Brown
Drop Point °C ASTM D566 170
Base oil viscosity @ 40 °C mm2/s ISO 3104 / ASTM D445 90
Worked Penetration,
25°C / 60 strokes 0.1mm ISO 2137 / ASTM D217 420 - 475
Anti-Rust Performance (Emcor) IP 220 / DIN 51802 0/1
Copper Corrosion, 24 h / 120 °C - DIN 51811 / ASTM D1261 1
Oxidation Stability, 100 h / 100 °C bar DIN 51808 / ASTM D942 0.2
Water Resistance, 3 h / 90 °C - DIN 51 807/1 1
Timken OK Load / Wear lbs / mg ASTM D2509 40 / 2
Flow Pressure -40 °C hPa DIN 51805 600
-35 °C hPa DIN 51805 300
-30 °C hPa DIN 51805 120
-20 °C hPa DIN 51805 40
DIN Classification GLP 00 DIN 51 502/51 826 K-30
The above figures are typical of those obtained with normal production tolerances, and do not constitute a specification. Note 1 mm2 s-1 = 1 cSt.

General Advice
Further information on all BP Marine lubricants is available from any BP Marine office or from:
BP Marine www.bpmarine.com
Technology Centre
Whitchurch Hill
Pangbourne
Reading RG8 7QR
United Kingdom

This data sheet and the information it contains is believed to be accurate as of the date of printing. However, no warranty or representation, express or implied, is made as to its accuracy
or completeness. Data provided is based on standard tests under laboratory conditions and is given as a guide only. Users are advised to ensure that they refer to the latest version of
this data sheet.
It is the responsibility of the user to evaluate and use products safely, to assess suitability for the intended application and to comply with all applicable laws and regulations. Material
Safety Data Sheets are available for all our products and should be consulted for appropriate information regarding storage, safe handling, and disposal of the product. No responsibility
is taken by either BP plc or its subsidiaries for any damage or injury resulting from abnormal use of the material, from any failure to adhere to recommendations, or from hazards inherent
in the nature of the material.
All products, services and information supplied are provided under our standard conditions of sale.
You should consult our local representative if you require any further information.
BP, the BP logo and ENERCARE are the trade marks of BP plc, used under licence. Produced by BP Marine Limited. Registered office: Chertsey Road, Sunbury-on-Thames,
Middlesex. TW16 7BP United Kingdom. Registered in England & Wales, no 01214291.
© 2009 BP Marine Limited. All rights reserved

13th October 2009

Version 2.0
Energrease LS-EP 00
Page 2 of 2