Scribd
Upload
9 views2 pages

MDB-1

The document contains a series of engineering problems related to stress, strain, and thermal expansion in various materials and structures. It includes calculations for shear stress, normal stress, tangential stress, and thermal stress under different loading conditions and geometries. Each problem specifies parameters such as dimensions, material properties, and applied forces or pressures.

Uploaded by

Angel Mulles
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views2 pages

MDB-1

The document contains a series of engineering problems related to stress, strain, and thermal expansion in various materials and structures. It includes calculations for shear stress, normal stress, tangential stress, and thermal stress under different loading conditions and geometries. Each problem specifies parameters such as dimensions, material properties, and applied forces or pressures.

Uploaded by

Angel Mulles
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

1.

​ A 100m diameter hole is punched through a 150mm thick steel plate if it has a
maximum shear strength of 500MPa what is the force needed to punch through it in
(ksi).
2.​ A solid circular shaft with a diameter of 10m transmits a torque of 1GNm. Find the
maximum shear stress(MPa) in the shaft.
3.​ A 20 mm diameter rivet is used to hold two metal plates together. The plates are
subjected to a shear force of 30KPa. Determine the shear stress(MPa) in the rivet.
4.​ A 10 ft steel shaft with a diameter of 5m is subjected to a tensile force of 100 ksi, find
its normal stress.
5.​ A hollow rectangular steel support must carry a compressive load of 10kN to
determine its area when the stress is limited to 10GPa.
6.​ The wall thickness of a 15m diameter spherical tank is 2.5 inch. Calculate the
allowable internal pressure if the stress is limited to 10.5 ksi.
7.​ A cylindrical steel pressure vessel 950 mm in diameter with a wall thickness of 80
mm, is subjected to an internal pressure of 10 MN/m2. (a) Calculate the tangential
and longitudinal stresses in the steel.
8.​ Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at
a pressure of 2500 psi. The diameter of the vessel is 2 m, and the stress is limited to
150 ksi.
9.​ A 15.5 ft-long bronze tube, with closed ends, is 27mm. in diameter with a wall
thickness of 0.10 m. With no internal pressure, the tube just fits between two rigid
end walls. Calculate the longitudinal and tangential stresses for an internal pressure
of 150 ksi.
10.​A trapezoidal steel block is 10 ft long in the x direction, 48 inches long in the y
direction, and 24 inches long in the z direction. The block is subjected to a triaxial
loading of three uniformly distributed forces as follows: 84 kips tension in the x
direction, 76 kips compression in the y direction, and 44 kips tension in the z
direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed
load in the x direction that would produce the same deformation in the y direction as
the original loading.
11.​10m.-diameter steel tube with a wall thickness of 250 mm just fits in a rigid hole. Find
the tangential stress if an axial compressive load of 3140 kip is applied.
12.​A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall
thickness of 3 mm. It fits without clearance in an 80-mm hole in a rigid block. The
tube is then subjected to an internal pressure of 4.00 MPa. Assuming ν = 1/3 and E =
83 GPa, determine the tangential stress in the tube.
13.​A steel rod with a diameter of 20 in and a length of 10ft is subjected to a tensile force
of 50 kN. If the Young’s modulus of steel is 250 GPa, determine the axial deformation
of the rod.
14.​A steel column with a cross-sectional area of 64 ft × 64 ft and a height of 3 m is
subjected to a compressive load of 80000 N. If the Young’s modulus of concrete is 80
GPa, determine the shortening of the column.
15.​A tapered steel bar has a diameter of 30 m at one end and 60 m at the other end
over a length of 150 ft. It is subjected to a tensile load of 120 MPa. If the Young’s
modulus of steel is 200 GPa, determine the approximate axial deformation.
16.​A steel rod is 2 m long and 2.5 m in diameter. It is heated from 20°C to 80°F while
both ends are fixed. If the coefficient of thermal expansion for steel is 12×10^-6°C^-1
and Young’s modulus is E = 200GPa, determine the thermal stress in the rod.
17.​A copper pipe of length 15 m is heated from 15°C to 190°C while its ends are fixed.
The coefficient of thermal expansion for copper is α=16×10^−6 °C^−1 and its Young’s
modulus isE=150 GPa. Find the thermal stress in the pipe.
18.​An aluminum rod is 1.8 m long and fixed at both ends. It experiences a temperature
increase from 30°F to 200°F. The coefficient of thermal expansion for aluminum is
α=23×10^−6 °C^−1 and Young’s modulus is E=70 GPa. Determine the thermal
stress.
19.​A brass bar of length 90 m is rigidly fixed at both ends. The temperature increases by
50°C. Given that the coefficient of thermal expansion for brass is α=19×10^−6 °C^−1
and Young’s modulus is E=50 GPa, calculate the thermal stress.
20.​A concrete beam of length 20m is heated from 10°K to 250°C while being fully
restrained. The coefficient of thermal expansion for concrete is α=10×10^−6 °C^−1
and Young’s modulus is E=300 GPa. Determine the thermal stress.

You might also like