What is Earthing:

In an electrical installation an earthing system or grounding system connects specific parts of

that installation with the Earth's conductive surface for safety and functional purposes.

Earthing is a part of electrical circuit which is done on initial level in order to connect the
electrical system with mass of earth so as to have discharge the electrical energy

Earthing is used to protect you from an electric shock. It does this by providing a path (a
protective conductor) for a fault current to flow to earth. It also causes the protective device
(either a circuit-breaker or fuse) to switch off the electric current to the circuit that has the fault.

What is the protective device:

CB, Fuse

Earthing in electrical network

The main reason for doing earthing in electrical network is for the safety. When all metallic
parts in electrical equipment are grounded then if the insulation inside the equipment fails
there are no dangerous voltages present in the equipment case.

The process of electrically connecting to the earth itself is often called “earthing”,
particularly in Europe where the term “grounding” is used to describe the above ground
wiring.
If the live wire touches the grounded case then the circuit is effectively shorted and fuse
will immediately blow. When the fuse is blown then the dangerous voltages are away.
Purpose of Earthing
1. Safety for Human life / Building /Equipment
 To save human life from danger of electrical shock or death by blowing a fuse i.e. To
provide an alternative path for the fault current to flow so that it will not endanger the
user
 To protect buildings, machinery & appliances under fault conditions.
 To ensure that all exposed conductive parts do not reach a dangerous potential.
 To provide safe path to dissipate lightning and short circuit currents.
 To provide stable platform for operation of sensitive electronic equipment i.e. To
maintain the voltage at any part of an electrical system at a known value so as to
prevent over current or excessive voltage on the appliances or equipment .
2. Over voltage protection
Lightning, line surges or unintentional contact with higher voltage lines can cause
dangerously high voltages to the electrical distribution system. Earthing provides an
alternative path around the electrical system to minimize damages in the System.

3. Voltage stabilization
There are many sources of electricity. Every transformer can be considered a separate
source. If there were not a common reference point for all these voltage sources it would
be extremely difficult to calculate their relationships to each other.

The earth is the most omnipresent conductive surface, and so it was adopted in the very
beginnings of electrical distribution systems as a nearly universal standard for all electric
systems.

<="" ins="" data-adsbygoogle-status="done" style="box-sizing: border-box; height: 280px;

width: 336px; display: block;">

Conventional methods of earthing

1. Plate type Earthing
 Generally for plate type earthing normal Practice is to use
 Cast iron plate of size 600 mm x600 mm x12 mm. OR
 Galvanized iron plate of size 600 mm x600 mm x6 mm. OR
 Copper plate of size 600 mm * 600 mm * 3.15 mm
 Plate burred at the depth of 8 feet in the vertical position and GI strip of size 50
mmx6 mm bolted with the plate is brought up to the ground level.
 These types of earth pit are generally filled with alternate layer of charcoal & salt up
to 4 feet from the bottom of the pit.
2. Pipe type Earthing
For Pipe type earthing normal practice is to use GI pipe [C-class] of 75 mm diameter , 10
feet long welded with 75 mm diameter GI flange having 6 numbers of holes for the
connection of earth wires and inserted in ground by auger method.

These types of earth pit are generally filled with alternate layer of charcoal & salt or earth
reactivation compound.

Method for Construction of Earthing Pit

 Excavation on earth for a normal earth Pit size is 1.5M X 1.5M X 3.0 M.
 Use 500 mm X 500 mm X 10 mm GI Plate or Bigger Size for more Contact of Earth
and reduce Earth Resistance.
 Make a mixture of Wood Coal Powder Salt & Sand all in equal part
 Wood Coal Powder use as good conductor of electricity, anti corrosive, rust proves
for GI Plate for long life.
 The purpose of coal and salt is to keep wet the soil permanently.
 The salt percolates and coal absorbs water keeping the soil wet.
 Care should always be taken by watering the earth pits in summer so that the pit soil
will be wet.
 Coal is made of carbon which is good conductor minimizing the earth resistant.
 Salt use as electrolyte to form conductivity between GI Plate Coal and Earth with
humidity.
 Sand has used to form porosity to cycle water & humidity around the mixture.
 Put GI Plate (EARTH PLATE) of size 500 mm X 500 mm X 10 mm in the mid of
mixture.
 Use Double GI Strip size 30 mm X 10 mm to connect GI Plate to System Earthling.
 It will be better to use GI Pipe of size 2.5″ diameter with a Flange on the top of GI
Pipe to cover GI Strip from EARTH PLATE to Top Flange.
 Cover Top of GI pipe with a T joint to avoid jamming of pipe with dust & mud and also
use water time to time through this pipe to bottom of earth plate.
 Maintain less than one Ohm Resistance from EARTH PIT conductor to a distance of
15 Meters around the EARTH PIT with another conductor dip on the Earth at least
500 mm deep.
 Check Voltage between Earth Pit conductors to Neutral of Mains Supply 220V AC 50
Hz it should be less than 2.0 Volts.

Factors affecting on Earth resistivity

1. Soil Resistivity
It is the resistance of soil to the passage of electric current. The earth resistance value
(ohmic value) of an earth pit depends on soil resistivity. It is the resistance of the soil to the
passage of electric current.

It varies from soil to soil. It depends on the physical composition of the soil, moisture,
dissolved salts, grain size and distribution, seasonal variation, current magnitude etc. In
depends on the composition of soil, Moisture content, Dissolved salts, grain size and its
distribution, seasonal variation, current magnitude.

2. Soil Condition
Different soil conditions give different soil resistivity. Most of the soils are very poor
conductors of electricity when they are completely dry. Soil resistivity is measured in ohm-
meters or ohm-cm.

Soil plays a significant role in determining the performance of electrode. Soil with low
resistivity is highly corrosive. If soil is dry then soil resistivity value will be very high. If soil
resistivity is high, earth resistance of electrode will also be high.

3. Moisture
Moisture has a great influence on resistivity value of soil. The resistivity of a soil can
be determined by the quantity of water held by the soil and resistivity of the water itself.
Conduction of electricity in soil is through water.

The resistance drops quickly to a more or less steady minimum value of about 15%
moisture. And further increase of moisture level in soil will have little effect on soil
resistivity. In many locations water table goes down in dry weather conditions.

Therefore, it is essential to pour water in and around the earth pit to maintain moisture in
dry weather conditions. Moisture significantly influences soil resistivity.
4. Dissolved salts
Pure water is poor conductor of electricity. Resistivity of soil depends on resistivity of water
which in turn depends on the amount and nature of salts dissolved in it.

Small quantity of salts in water reduces soil resistivity by 80%. Common salt is most effective in
improving conductivity of soil . But it corrodes metal and hence discouraged.

5. Climate Condition
Increase or decrease of moisture content determines the increase or decrease of soil
resistivity. Thus in dry whether resistivity will be very high and in monsoon months the
resistivity will be low.

6. Physical Composition
Different soil composition gives different average resistivity. Based on the type of soil, the
resistivity of clay soil may be in the range of 4 – 150 ohm-meter , whereas for rocky or
gravel soils, the same may be well above 1000 ohm-meter.

7. Location of Earth Pit

The location also contributes to resistivity to a great extent. In a sloping landscape, or
in a land with made up of soil, or areas which are hilly, rocky or sandy, water runs off and
in dry weather conditions water table goes down very fast. In such situation back fill
compound will not be able to attract moisture, as the soil around the pit would be dry.

The earth pits located in such areas must be watered at frequent intervals , particularly
during dry weather conditions.

Though back fill compound retains moisture under normal conditions, it gives off moisture
during dry weather to the dry soil around the electrode, and in the process loses moisture
over a period of time. Therefore, choose a site that is naturally not well drained.
8. Effect of grain size and its distribution
Grain size, its distribution and closeness of packing are also contributory factors, since
they control the manner in which the moisture is held in the soil.

Effect of seasonal variation on soil resistivity: Increase or decrease of moisture content

in soil determines decrease or increase of soil resistivity. Thus in dry weather resistivity will
be very high and during rainy season the resistivity will be low.

9. Effect of current magnitude

Soil resistivity in the vicinity of ground electrode may be affected by current flowing from
the electrode into the surrounding soil. The thermal characteristics and the moisture
content of the soil will determine if a current of a given magnitude and duration will cause
significant drying and thus increase the effect of soil resistivity.

10. Area Available

Single electrode rod or strip or plate will not achieve the desired resistance alone.

If a number of electrodes could be installed and interconnected the desired resistance

could be achieved. The distance between the electrodes must be equal to the driven depth
to avoid overlapping of area of influence. Each electrode, therefore, must be outside the
resistance area of the other .

11. Obstructions
The soil may look good on the surface, but there may be obstructions below a few feet like
virgin rock. In that event resistivity will be affected. Obstructions like concrete structure
near about the pits will affect resistivity.

If the earth pits are close by, the resistance value will be high .
12. Current Magnitude
A current of significant magnitude and duration will cause significant drying condition in soil
and thus increase the soil resistivity.

Measurement of Earth Resistance by use of

Earth Tester
For measuring soil resistivity Earth Tester is used. It is also called the “MEGGER”.

 It has a voltage source, a meter to measure Resistance in ohms, switches to change

instrument range, Wires to connect terminal to Earth Electrode and Spikes.
 It is measured by using Four Terminal Earth Tester Instrument. The terminals are
connected by wires as in illustration.
 P=Potential Spike and C=Current Spike. The distance between the spikes may be
1M, 2M, 5M, 10M, 35M, and 50M.
 All spikes are equidistant and in straight line to maintain electrical continuity. Take
measurement in different directions.
 Soil resistivity =2πLR.
 R= Value of Earth resistance in ohm.
 Distance between the spikes in cm.
 π = 3.14
 P = Earth resistivity ohm-cm.
 Earth resistance value is directly proportional to Soil resistivity value

Measurement of Earth Resistance (Three

point method)
In this method earth tester terminal C1 and P1 are shorted to each other and connected to
the earth electrode (pipe) under test. Terminals P2 and C2 are connected to the two
separate spikes driven in earth. These two spikes are kept in same line at the distance of
25 meters and 50 meters due to which there will not be mutual interference in the field of
individual spikes.

If we rotate generator handle with specific speed we get directly earth resistance on
scale. Spike length in the earth should not be more than 1/20th distance between two
spikes. Resistance must be verified by increasing or decreasing the distance between the
tester electrode and the spikes by 5 meter.

Normally, the length of wires should be 10 and 15 meters or in proportion of 62% of ‘D’.

Suppose, the distance of Current Spike from Earth Electrode D = 60 ft, Then, distance of
Potential Spike would be 62 % of D = 0.62D i.e. 0.62 x 60 ft = 37 ft.

Four Point Method

In this method 4 spikes are driven in earth in same line at the equal distance. Outer two
spikes are connected to C1 & C2 terminals of earth tester. Similarly inner two spikes are
connected to P1 & P2 terminals. Now if we rotate generator handle with specific speed,
we get earth resistance value of that place.

In this method error due to polarization effect is eliminated and earth tester can be
operated directly on A.C.

GI Earthing Vs Copper Earthing

 As per IS 3043, the resistance of Plate electrode to earth (R) = (r/A) X under
root(P/A).
 Where r = Resistivity of Soil Ohm-meter.
 A=Area of Earthing Plate m3.
 The resistance of Pipe electrode to earth (R) = (100r/2πL) X loge (4L/d).
 Where L= Length of Pipe/Rod in cm
 d=Diameter of Pipe/Rod in cm.
 The resistivity of the soil and the physical dimensions of the electrode play important
role of resistance of Rod with earth.
 The material resistivity is not considered important role in earth resistivity.
 Any material of given dimensions would offer the same resistance to earth. Except
the sizing and number of the earthing conductor or the protective conductor.

Pipe Earthing Vs Plate Earthing

 Suppose Copper Plate having of size 1.2m x 1.2m x 3.15mm thick. soil resistivity of
100 ohm-m,
 The resistance of Plate electrode to earth (R)=( r/A)X under root(π/A) =
(100/2.88)X(3.14/2.88)=36.27 ohm
 Now, consider a GI Pipe Electrode of 50 mm Diameter and 3 m Long. soil resistivity
of 100 Ohm-m,
 The resistance of Pipe electrode to earth (R) = (100r/2πL) X loge (4L/d) =
(100X100/2X3.14X300) X loge (4X300/5) =29.09 Ohm.
 From the above calculation the GI Pipe electrode offers a much lesser resistance
than even a copper plate electrode.
 As per IS 3043 Pipe, rod or strip has a much lower resistance than a plate of
equal surface area.

Length of Pipe Electrode and Earthing Pit

The resistance to earth of a pipe or plate electrode reduces rapidly within the first few feet
from ground (mostly 2 to 3 meter) but after that soil resistivity is mostly uniform.
After about 4 meter depth, there is no appreciable change in resistance to earth of the
electrode. Except a number of rods in parallel are to be preferred to a single long rod.

Amount of Salt and Charcoal (more than

8Kg)
To reduce soil resistivity, it is necessary to dissolve in the moisture particle in the Soil.
Some substance like Salt/Charcoal is highly conductive in water solution but the additive
substance would reduce the resistivity of the soil, only when it is dissolved in the moisture
in the soil after that additional quantity does not serve the Purpose.

5% moisture in salt reduces earth resistivity rapidly and further increase in salt content will
give a very little decrease in soil resistivity.

The salt content is expressed in percent by weight of the moisture content in the soil.
Considering 1M3 of Soil, the moisture content at 10 percent will be about 144 kg. (10
percent of 1440 kg). The salt content shall be 5% of this (i.e.) 5% of 144kg, that is, about
7.2kg.

Length Vs Diameter of Earth Electrode

Apart from considerations of mechanical strength, there is little advantage to be gained
from increasing the earth electrode diameter with the object in mind of increasing surface
area in contact with the soil.

The usual practice is to select a diameter of earth electrode, which will have enough strength to
enable it to be driven into the particular soil conditions without bending or splitting. Large
diameter electrode may be more difficult to drive than smaller diameter electrode.

The depth to which an earth electrode is driven has much more influence on its electrical
resistance characteristics than has its diameter.

Maximum allowable Earth resistance

 Major power station = 0.5 Ohm
 Major Sub-stations = 1.0 Ohm
  Minor Sub-station = 2 Ohm
 Neutral Bushing = 2 Ohm
 Service connection = 4 Ohm
 Medium Voltage Network = 2 Ohm
 L.T.Lightening Arrestor = 4 Ohm
 L.T.Pole = 5 Ohm
 H.T.Pole = 10 Ohm
 Tower = 20-30 Ohm

Treatments to for minimizing Earth

resistance
 Remove Oxidation on joints and joints should be tightened.
 Poured sufficient water in earth electrode.
 Used bigger size of Earth Electrode.
 Electrodes should be connected in parallel.
 Earth pit of more depth & width- breadth should be made.

Equipment Earthing

Lightening Protection

Q: In the 3 phase LT distribution of building some earth pits for eqipment earthing are built
and some earth pit for lightning protection to building are built . Please advise whether for
effectively low earth pit resistance the earth pist of equipment and earth pits of lightning
can be made parallel

Ans: Earth pits for equipment and lightning should NOT be made parallel.