Back to Table of Contents

20 Series
S20A1
Application Sheet
23.260 (590,80)
23.240 (590,30) 23.25
DIA. (590,6)
FRAME MOUNT HOLES 19.000 DIA. 9˚
3/4-10 UNC-2B THD. 18.990 18˚
1.31 (33,3) MIN. FULL THD. 45˚
(482,60)
TYP. (20) HOLES EQ. SPACED (482,35)
ON 21.900 (556,26) DIA. B.C. PILOT DIA.
.060 R
11.00 (1,52) MAX.
(279,4) MOTOR MOUNT HOLES
DIA. 90˚ 105˚
1/2-13 UNC-2B THD.
AS CAST .90 (22,8) MIN. FULL THD.
4.00 TYP. (4) HOLES
(101,6) EQ. SPACED ON
1.504 5.125 MIN. FULL
5.124 6.375 (161,93)
1.500 KEYWAY DIA. B.C.
(38,20) (130,18)
(38,10) (130,15)
KEYWAY DIA.
WIDTH
90˚
.59
(15,1)
4.262
4.252 S20A1 3.00
(108,25) (76,2) MOTOR MOUNT HOLES
(108,00) MAX. 5/8-11 UNC-2B THD.
INPUT SHAFT 1.10 (28,2) MIN. FULL THD.
LENGTH ALL TYP. (2) HOLES
INPUTS
END OF INPUT
- 180˚ APART ON SAE "C" MOUNT
7.125 (180,98)
1/2-20 UNF-2B THD. .100 R SPLINE TO DIA. B.C.
1.00 (25,4) MIN. FULL THD. (2,54) MOTOR MOUNT
TYP. (2) HOLES EQ. SPACED MAX. FACE OUTPUT ROTATION
AS SHOWN 1.04 (26,4) MIN. SAME AS INPUT
ON 2.500 (63,50) DIA. B.C. FOR 14T 12/24 ROTATION

1.53 (38,8) MIN.

FOR 13T 8/16

5.00
(127,0)
12.57 ± .07
(319,2 ± 1,8) .66 (16,8)
25.19 (639,8) MAX.
3.00 MOTOR MOUNT HOLES
(76,2) 24.19 (614,4) MAX. 3/4-10 UNC-2B THD.
1/2-20 UNF-2B THD. 11.57 ± .07
1.00 (25,4) MIN. FULL THD. MIN. 1.31 (35,3) MIN
(293,8 ± ,1)
TYP. (2) HOLES EQ. SPACED FULL 4.00 (101,6) FULL THREAD
ON 2.500 (63,50) DIA. B.C. SPLINE TYP. (4) HOLES
EQ. SPACED ON
9.000 (228,60) DIA. B.C.
OUTPUT SPLINE
5.125 (130,18) 40 TOOTH, 8/16 PITCH
5.115 (129,92) S20A2 30˚ P.A. SIDE FIT SPLINE
DIA. PER ANSI B92.1-1970
CLASS 6
SAE "D" MOUNT

NOTE: MM SHOWN IN ( ) OTHER MODELS ALSO AVAILABLE

MOTOR CAVITY DIMENSIONS VARY WITH MODEL FAIRFIELD BRAKE AVAILABLE
Back to Table of Contents
Torque-Hub® 20 Series
S20A1
Performance Data Oil Bearing Curve
Continuous Intermittent Peak Fill to half full with 90 weight gear lube with EP additive 30000

250,000 lb-in 500,000 lb-in 600,000 lb-in on most applications. 28000

100. RPM 3000. HOURS
20,833 lb-ft 41,667 lb-ft 50,000 lb-ft 26000
3
28,245 Nm 56,490 Nm 67,800 Nm Approximate Volume 256 oz. (7,573 cm )
24000
2,880 kg-m 5,760 kg-m 6,900 kg-m
22000

For ultimate torque and horsepower capacities, contact a Torque-Hub® representative. Note: Oil level and type will vary with specific model and application.

ALLOWABLE RADIAL LOAD (lbs.)

20000

18000
Speed Limitations Conditions of Bearing Curve
16000

Input Speed: 1,500- 1,800 RPM Maximum Intermittent Life = 3,000 hours B-10 14000

Speed = 100 RPM output 12000

MAX BEARING LIFE LINE (2.02)

(Contact Fairfield for specific speed information.) 10000

To adjust for loads and speeds other than shown on curve:

Weight 8000

HUB MTG. FACE

100 RPM Load (Curve) 10/3 6000
Approximately 1,350 lbs (608 kg)
(
Adjusted Life (hrs) =3,000 Speed (Adjusted) x Load (Adjusted))( ) 4000

2000
Note: Specific models will change weights.
0

11

9
8
7
6
5
4
3
2
1
0
-1
20
19
18
17
16
15
14
13
12

10
S20A1 Model Formula
S 20 A1 9 4 4 116 DISTANCE FROM HUB MOUNTING FACE (in)

S – Torque-Hub® Shaft Output

Reduction
27 – 27.2:1
20 – Series
37 – 37.6:1
54 – 54.2:1
62 – 62.2:1
Shaft Hub
86 – 86.3:1
Hub Flange Flange B.C. 116 – 116.3:1
Configuration
Thickness
A1 5.125 Dia. No Flange (20) 3/4-10 Holes
1-1/2" Keyway 21.900 B.C.

A2 5.125 Dia. No Flange (20) 3/4-10 Holes Input

40T, 8/16 Spline 21.900 B.C. 4 – 14T, 12/24 Spline
5 – 13T, 8/16 Spline

Internal Gear Motor Mount

4 – Reduction 27:1 & 54:1 4 – S.A.E. “C” (5.005/5.001) Pilot (2 & 4 Bolt)
5 – Reduction 37:1 & 62:1 5 – S.A.E. “D” (6.005/6.001) Pilot
Fairfield Manufacturing Company, Inc.
First in Custom Gears and Drive Systems 9 – Reduction 86:1 & 116:1
U.S. 52 South
P.O. Box 7940
Lafayette, IN 47903-7940 USA
Telephone (765) 772-4000 Torque-Hub is a registered trademark of Fairfield.
FAX (765) 772-4001 © 2000 Fairfield Manufacturing Company, Inc.
www.fairfieldmfg.com

99