Scribd
Upload
1K views

MSS MGW MC Interface

This document provides configuration instructions for setting up signaling and interconnection between an MSS and an MGW using M3UA and H.248 protocols. It describes creating associations, links, and routes for M3UA signaling over IPv4 between the MSS and MGW. It also covers configuring a virtual MGW in H.248, attaching TDM circuits between the MSS and MGW, and registering the MGW with the MSS.

Uploaded by

CoachArun Mishra
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

MSS MGW MC Interface

This document provides configuration instructions for setting up signaling and interconnection between an MSS and an MGW using M3UA and H.248 protocols. It describes creating associations, links, and routes for M3UA signaling over IPv4 between the MSS and MGW. It also covers configuring a virtual MGW in H.248, attaching TDM circuits between the MSS and MGW, and registering the MGW with the MSS.

Uploaded by

CoachArun Mishra
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

/* Kutola MSS configuration macro, modified by MIV 04.12.2003 SW packages Kutoja:MGW5 8.1-0, MSS 7.1-0 (env MC 7.

5-0) Signalling point codes: MSS Kutoja = 950 MGW01 Kutoja = 2810 BSC02(MGW01) = 320 RNC01 = 2710 Contents: MSS-MGW -------- >>>>>>>>>>>>>>>>>>>> EXECUTION IN MSS<<<<<<<<<<<<<<<<<<<<<<<<<------

//MSS-MGW:SIGTRAN: //================ //Network interface IPv4, //M3UA based signalling (=IP based signalling): //(association set, association, IP signalling link set & link, signalling route ZQRN:CCSU,0::EL0:10.2.80.40,L,:24:UP:;//Configure network interface (IPv4) ZQRC:CCSU,0:::GW:IP:IP=10.2.80.2;//Create default static route (IPv4). ZOYC:MGW01:C:M3UA:;//Create association set (MSS is the client) ZOYA:MGW01:CCSU,0,:"10.2.80.20",24::IETF;//Add association to association set. Define destination MGW ISU IP. ZOYM:MGW01:VERSION=16:;//Modify association. Version RFC 1.0 (M3UA specification version) ZOYM:MGW01:ASP=N;//Modify association set. ASP=ASP messages in ipsp. ZOYM:MGW01:FIRST=1:;//Modify association set. FIRST=first data stream number. //Also check Network appearance, 8 may work, and stream no 1. ZNSP:NA0,2810,MGW01:99:MGW01;//Create IP signalling link set. This creates also link. ZNRC:NA0,2810,MGW01,6,,:,,,7;//Create signalling route set. Set Parameter set 6 (IETF M3UA) //ZNST:NA0,2801,MGW01:N;//Set signalling link test status to NOT ALLOWED //MSS-MGW:Activate IP signalling link & route: //============================================ //when corresponding configuration ready in MGW side also. ZNLA:99:;//Allow activation of signalling link ZNLC:99,ACT;//Activate signalling link ZNVA:NA0,2810;//Allow activation of signalling route ZNVC:NA0,2810:,:ACT;//Activate signalling route //MSS-MGW:Create MGW: //=================== //TRFO not implemented yet //NOT NEEDED: Activate parameter ZWOA:53,1,A; Create MGW with ZJGC. Deactivate parameter ZWOA:53.1,D ZJGC:ADDR="10.2.80.20",PORT=8010,NAME=MGW01,MGWTYP=GEN:UTYP=CCSU,UINX=0,UADDR="1 0.2.80.40",E164=35860,LBCU=0,REGA=Y,TTY=SCTP,NBR=0;//Create MGW. //ADDR=MGW ISU IP. UADDR=MSS CCSU IP. //REGA=Allow MGW registration. //MSS-MGW:Create interconnection TDM: //===================================

ZRCC:TYPE=SPE,NCGR=MGW01,CGR=593:HUNTED=Y,USE=INTC:MGW=MGW01,:;//Create SPE cgr. INTC=interconnect CGR for TDM-circuits. ZRCA:CGR=593:CRCT=593-1&&-31:TERMPCM=15:;//Add circuits. Termpcm must match with PCM in corresponding SPE cgr in MGW. ZRRC:INT,GSW:ROU=593,NCGR=MGW01,OUTR=OMCG0:;//Create route. ZJGM:MGWID=0::ROU=593,;// Attach created internal route to the VMGW ZCIM:GSW:CGR=593:WO;//Change cgr state. ZCIM:GSW:CRCT=593-1&&-31:WO;//Change crct state. //MSS-MGW:Register MGW from MGW side: //=================================== //This is part of user plane resources. //Register MGW from MGW side after MGW and interconnection TDM MGW-MSS have been //created in MGW side also. MSS must have registration allowed REGA=Y before MGW can register. -------- >>>>>>>>>>>>>>>>>>>> EXECUTION IN MEDIA GATEWAY <<<<<<<<<<<<<<-----//MGW-MSS:SIGTRAN: //================ //Network interface IPv4, //M3UA based signalling (=IP based signalling): //(association set, association, IP signalling link set & link, signalling route ZQRN:ISU,0:EL0:10.2.80.20,L,:24:::UP:;//Create network interface (IPv4). QRC:ISU,0::GW:IP:IP=10.2.80.2;//Create default static route (IPv4). ZOYC:MSS01:S:M3UA:;//Create association set.MGW is the server. ZOYA:MSS01:ISU,0,:"10.2.80.40",24::IETF;//Add association to association set (SIGTRAN done). Define destination MSS CCSU IP address. ZOYM:MSS01:VERSION=16:;//Modify association. Version RFC 1.0 (M3UA spesification version) ZOYM:MSS01:ASP=N;//Modify association set. ASP=ASP messages in ipsp. ZOYM:MSS01:FIRST=1:;//Modify association set. FIRST=first data stream number. //Also check Network appearance, 8 may work, and stream no 1. ZNSP:NA0,950,MSS01:99:MSS01;//Create IP sign.link set for MSS. This creates also link. ZNST:NA0,394,INMSS:N;//Set signalling link test status to NOT ALLOWED. See MGW Rel4 integration manual. ZNRC:NA0,950,MSS01,6,,:,,,7;//Create sign.route set for MSS. Parameter set number 6 IETF. Priority 7. //MGW-MSS:Activate IP signalling link & route: //============================================ //when corresponding configuration ready in MSS side also. ZNLA:99;//Allow activation of sign.link. ZNLC:99,ACT;//Activate sign.link. ZNVA:NA0,950;//Allow activation of sign.route. ZNVC:NA0,950::ACT;//Activate sign.route. //MGW-MSS:Interconnection TDM: //============================ //Interface unit HW:NIWU ET. ET functional mode should be same in MGW and MSS. Mode e.g. DBLF (ZYEI, ZYEC). ZRCC:TYPE=SPE,CGR=15,NCGR=MSS01:USE=VMGW:;//Create cgr. Type is SPEcial. Used by VMGW. ZRCA:CGR=15:CRCT=15-1&&-31:;//Add circuits. PCM in CRCT must match with TERMPCM in corresponding SPE cgr in MSS. ZCIM:CRCT=15-1&&-31:WO;//Activate circuits.

ZCIM:NCGR=MSS01:WO;//Activate cgr. //MGW-MSS:H.248, Virtual MGW: //=========================== //Configuring H.248 control protocol=IPv4 network interface configuration with ZQRN earlier //+ virtual MGW configuration. ZJVC:VMN=MGW01,UINX=0,:OIP="10.2.80.20",OPN=8010,:A2T=50,:TTY=0,CTY=0,:PIP="10.2 .80.40",::DUR=00-01-00; ZJVM:VMN=MGW01:CGR=15;//Attach interconnection TDM MGW-MSS to virtual MGW. //If MGW has been created in MSS and its registration has been allowed in MSS, then register MGW: ZJVR:VMN=MGW01,:REGA=1:;//Register MGW.

You might also like