Diagnosing Report 1XKADP8X3CJ317972

Source Code Status Description Hours Count

1 Cab Electronic Control Unit 3 24709 Inactive Engine Total Hours of Operation message 6902 1
missing
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 10.294 V
Outside Air Temperature 110 °F
Coolant Temperature 100 °F
Detailed Description This DTC will be recorded when the control unit does not see the Engine Total
Hours of Operation message from the engine, or when the message has timed
out. Some possible causes for this include faulty wiring to the engine controller
or a faulty engine controller.

2 Cab Electronic Control Unit 3 24809 Inactive Total Power Takeoff Hours message missing 6902 7

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 10.294 V
Outside Air Temperature 110 °F
Coolant Temperature 100 °F
Detailed Description This DTC will be recorded when the control unit does not see the Total PTO
Hours message from the engine, or when the message has timed out. Some
possible causes for this include faulty wiring to the engine controller or a
faulty/misconfigured engine controller.

3 Cab Electronic Control Unit 3 59631 Inactive Cruise Control Rationality Check 0 1

Name Value Unit

Engine RPM N/A RPM
Vehicle Speed N/A MPH
Battery Voltage N/A V
Outside Air Temperature N/A °F
Coolant Temperature N/A °F
Detailed Description This DTC will be recorded when the driver attempts to set the SET or
RESUME before he has touched the brake and the clutch. This fault will
remain active until the keyswitch is cycled.

4 Cab Electronic Control Unit 3 82903 Inactive Open in primary fuel level circuit 6818 24

Name Value Unit

Engine RPM 619 RPM
Vehicle Speed 3 MPH
Battery Voltage 13.918 V
Outside Air Temperature 100 °F
Coolant Temperature 120 °F
Detailed Description This DTC will be recorded when the control unit sees an open at the primary
fuel level sensor input. Some possible causes for this are a broken wire,
corroded or disconnected connector, or sensor failure.

Report Date: 11/16/2024 4:29:53PM 1/7

 Source Code Status Description Hours Count
5 Cab Electronic Control Unit 3 102809 Inactive Total Engine PTO Fuel Used Message missing 7519 1

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.845 V
Outside Air Temperature 69 °F
Coolant Temperature 189 °F
Detailed Description This DTC will be recorded when the control unit does not see the Total Engine
PTO Fuel Used message from the engine, or when the message has timed
out. Some possible causes for this include faulty wiring to the engine controller
or a faulty/misconfigured engine controller.

6 Cab Electronic Control Unit 3 123109 Inactive Control unit cannot read messages from 6818 126
Cluster on I-CAN
Name Value Unit
Engine RPM 37 RPM
Vehicle Speed 52 MPH
Battery Voltage 12.248 V
Outside Air Temperature 112 °F
Coolant Temperature 104 °F
Detailed Description This DTC will be recorded when the CECU cannot read messages from the
cluster. Some possible causes for this are a broken wire, corroded or
disconnected connector, no power to the cluster or cluster failure. Check
condition of I-CAN wiring and resistance.

7 Cab Electronic Control Unit 3 148109 Inactive Control unit cannot read messages from ABS 6915 33
on V-CAN
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.758 V
Outside Air Temperature 67 °F
Coolant Temperature 109 °F
Detailed Description This DTC will be recorded when the control unit cannot read messages from
the ABS system. Some possible causes for this are a broken wire, corroded or
disconnected connector, no terminating resistors, no power to the ABS system
or ABS ECU failure.

8 Cab Electronic Control Unit 3 148209 Inactive Control unit cannot read messages from 7018 9
Transmission on V-CAN
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.782 V
Outside Air Temperature 56 °F
Coolant Temperature 196 °F
Detailed Description This DTC will be recorded when the control unit cannot read messages from
the transmission ECU. Some possible causes for this are a broken wire,
corroded or disconnected connector, no terminating resistors, no power to the
Transmission or Transmission ECU failure.

Report Date: 11/16/2024 4:29:54PM 2/7

 Source Code Status Description Hours Count
9 Cab Electronic Control Unit 3 148309 Inactive Control unit cannot read messages from 7018 10
Engine on V-CAN
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.782 V
Outside Air Temperature 56 °F
Coolant Temperature 196 °F
Detailed Description This DTC will be recorded when the control unit cannot read messages from
the engine ECU. Some possible causes for this are a broken wire, corroded or
disconnected connector, no terminating resistors, no power to the engine or
engine ECU failure.

10 Cab Electronic Control Unit 3 148704 Inactive Short in dash dimmer input circuit 6902 2

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the control unit sees a short to ground at the
dash light dimmer control input. Some possible causes for this are a pinched
wire, water in a connector, or dimmer control failure.

11 Cab Electronic Control Unit 3 234813 Inactive Left or Right High Beam Output General Error 6902 1

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the Left or Right High Beam output on the
chassis node is not functioning correctly. Some possible causes for this are
damaged wiring between chassis node and headlamps, corroded connections,
water in connectors, disconnected connectors, or a failed bulb. This DTC is
likely to be recorded when more specific high beam DTCs are recorded.

12 Cab Electronic Control Unit 3 235005 Inactive Left or Right Low Beam Output Under Current 7049 19
or Open Circuit
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.587 V
Outside Air Temperature 69 °F
Coolant Temperature 117 °F
Detailed Description This DTC will be recorded when the Left or Right Low Beam output on the
chassis node detects low current or open circuit. Possible causes are failed
bulbs, damaged wiring harness between chassis node and headlamps,
corroded connectors, or incorrect parameter settings for headlamps on this
vehicle.

Report Date: 11/16/2024 4:29:54PM 3/7

 Source Code Status Description Hours Count
13 Cab Electronic Control Unit 3 235013 Inactive Left or Right Low Beam Output General Error 6902 1

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the Left or Right Low Beam output on the
chassis node is not functioning correctly. Some possible causes for this are
damaged wiring between chassis node and headlamps, corroded connections,
water in connectors, disconnected connectors, or a failed bulb. This DTC is
likely to be recorded when more specific low beam DTCs are recorded.

14 Cab Electronic Control Unit 3 236813 Inactive Left Front Turn or Left Front Side Turn Output 6902 2
General Error
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the Left Front Turn or Left Front Side Turn
output on the chassis node is not functioning correctly. The Left Front Turn
may also function as the Left Daytime Running Lamp on some truck models.
Some possible causes for this are damaged wiring between chassis node and
turn lamps, corroded connections, water in connectors, disconnected

15 Cab Electronic Control Unit 3 237013 Inactive Right Front Turn or Right Front Side Turn 6902 3
Output General Error
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the Right Front Turn or Right Front Side Turn
output on the chassis node is not functioning correctly. The Right Front Turn
may also function as the Right Daytime Running Lamp on some truck models.
Some possible causes for this are damaged wiring between chassis node and
turn lamps, corroded connections, water in connectors, disconnected

16 Cab Electronic Control Unit 3 237201 Inactive Left Rear Turn/Stop Output General Error 6903 126

Name Value Unit

Engine RPM 1390 RPM
Vehicle Speed 18 MPH
Battery Voltage 13.278 V
Outside Air Temperature 117 °F
Coolant Temperature 190 °F
Detailed Description This DTC will be recorded when the Left Rear Turn/Stop output on the chassis
node is not functioning correctly. Some possible causes for this are damaged
wiring between chassis node and rear turn/stop lamps, corroded connections,
water in connectors, disconnected connectors, or a failed bulb. This DTC is
likely to be recorded when more specific rear turn/stop lamp DTCs are

Report Date: 11/16/2024 4:29:54PM 4/7

 Source Code Status Description Hours Count
17 Cab Electronic Control Unit 3 237205 Inactive Left Rear Turn/Stop Output Under Current or 6903 126
Open Circuit
Name Value Unit
Engine RPM 1390 RPM
Vehicle Speed 18 MPH
Battery Voltage 13.278 V
Outside Air Temperature 117 °F
Coolant Temperature 190 °F
Detailed Description This DTC will be recorded when the Left Rear Turn/Stop output on the chassis
node has low current or open circuit. Some possible causes are failed bulbs,
damaged wiring harness between chassis node and turn lamps, corroded
connectors, or incorrect parameter settings for rear turn/stop lamps on this
vehicle.

18 Cab Electronic Control Unit 3 237213 Inactive Left Rear Turn/Stop Output General Error 6902 2

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the Left Rear Turn/Stop output on the chassis
node is not functioning properly. Some possible causes for this are damaged
wiring between chassis node and rear turn/stop lamps, corroded connections,
water in connectors, disconnected connectors, or a failed bulb. This DTC is
likely to be recorded when more specific rear turn/stop lamp DTCs are

19 Cab Electronic Control Unit 3 237401 Inactive Right Rear Turn/Stop Output General Error 6903 126

Name Value Unit

Engine RPM 1237 RPM
Vehicle Speed 12 MPH
Battery Voltage 13.29 V
Outside Air Temperature 117 °F
Coolant Temperature 189 °F
Detailed Description This DTC will be recorded when the Right Rear Turn/Stop output on the
chassis node is not functioning correctly. Some possible causes for this are
damaged wiring between chassis node and rear turn/stop lamps, corroded
connections, water in connectors, disconnected connectors, or a failed bulb.
This DTC is likely to be recorded when more specific rear turn/stop lamp DTCs

20 Cab Electronic Control Unit 3 237405 Inactive Right Rear Turn/Stop Output Under Current or 6903 126
Open Circuit
Name Value Unit
Engine RPM 1237 RPM
Vehicle Speed 12 MPH
Battery Voltage 13.29 V
Outside Air Temperature 117 °F
Coolant Temperature 189 °F
Detailed Description This DTC will be recorded when the Right Rear Turn/Stop output on the
chassis node has low current or open circuit. Some possible causes are failed
bulbs, damaged wiring harness between chassis node and turn lamps,
corroded connectors, or incorrect parameter settings for rear turn/stop lamps
on this vehicle.

Report Date: 11/16/2024 4:29:54PM 5/7

 Source Code Status Description Hours Count
21 Cab Electronic Control Unit 3 237413 Inactive Right Rear Turn/Stop Output General Error 6902 1

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the Right Rear Turn/Stop output on the
chassis node is not functioning properly. Some possible causes for this are
damaged wiring between chassis node and rear turn/stop lamps, corroded
connections, water in connectors, disconnected connectors, or a failed bulb.
This DTC is likely to be recorded when more specific rear turn/stop lamp DTCs

22 Cab Electronic Control Unit 3 239601 Inactive Left Trailer Turn Output General Error 7001 61

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.69 V
Outside Air Temperature 85 °F
Coolant Temperature 162 °F
Detailed Description This DTC will be recorded when the Left Trailer Turn Lamp output on the
chassis node is not functioning correctly. Some possible causes for this are
damaged wiring between chassis node and left trailer turn lamps, corroded
connections, water in connectors, disconnected connectors, or a failed bulb.
This DTC is likely to be recorded when more specific left trailer turn lamp

23 Cab Electronic Control Unit 3 239605 Inactive Left Trailer Turn Output Under Current or Open 7001 13
Circuit
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.69 V
Outside Air Temperature 85 °F
Coolant Temperature 162 °F
Detailed Description This DTC will be recorded when the Left Trailer Turn Lamp output on the
chassis node has low current or open circuit. Some possible causes are failed
bulbs, damaged wiring harness between chassis node and left trailer turn
lamps, corroded connectors.

24 Cab Electronic Control Unit 3 239801 Inactive Right Trailer Turn Output General Error 6924 126

Name Value Unit

Engine RPM 1223 RPM
Vehicle Speed 22 MPH
Battery Voltage 14.103 V
Outside Air Temperature 75 °F
Coolant Temperature 189 °F
Detailed Description This DTC will be recorded when the Right Trailer Turn Lamp output on the
chassis node is not functioning correctly. Some possible causes for this are
damaged wiring between chassis node and right trailer turn, corroded
connections, water in connectors, disconnected connectors, or a failed bulb.
This DTC is likely to be recorded when more specific right trailer turn lamp

Report Date: 11/16/2024 4:29:54PM 6/7

 Source Code Status Description Hours Count
25 Cab Electronic Control Unit 3 239805 Inactive Right Trailer Turn Output Under Current or 6924 80
Open Circuit
Name Value Unit
Engine RPM 1223 RPM
Vehicle Speed 22 MPH
Battery Voltage 14.103 V
Outside Air Temperature 75 °F
Coolant Temperature 189 °F
Detailed Description This DTC will be recorded when the Right Trailer Turn Lamp output on the
chassis node has low current or open circuit. Some possible causes are failed
bulbs, damaged wiring harness between chassis node and right trailer turn
lamps, corroded connectors.

26 Cab Electronic Control Unit 3 286302 Inactive Invalid Range High Speed Wiper Switch Input 6818 126

Name Value Unit

Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 12.219 V
Outside Air Temperature 100 °F
Coolant Temperature 115 °F
Detailed Description This DTC will be recorded when the control unit sees an invalid voltage range
on the high speed wiper switch input. Some possible causes are broken wire,
corroded or disconnected connector or faulty turn stalk switch.

27 Cab Electronic Control Unit 3 286307 Inactive Out of Range on Low Speed Wiper Switch 6902 126
Input
Name Value Unit
Engine RPM 0 RPM
Vehicle Speed 0 MPH
Battery Voltage 0 V
Outside Air Temperature -459 °F
Coolant Temperature 32 °F
Detailed Description This DTC will be recorded when the control unit sees an out of range voltage
value on the low speed wiper switch. Some possible causes are broken wire,
corroded or disconnected connector or faulty turn stalk switch.

28 Cab Electronic Control Unit 3 287607 Inactive Turn Signal Switch Input Out of Range 6904 126

Name Value Unit

Engine RPM 1306 RPM
Vehicle Speed 62 MPH
Battery Voltage 14.023 V
Outside Air Temperature 93 °F
Coolant Temperature 190 °F
Detailed Description This DTC will be recorded when the control unit sees the value of the turn
signal input to the control unit on the turn stalk in an invalid range. The input is
in an invalid range if the value is between 235Ω and 270Ω or between 580Ω
and 685Ω. Potential causes for this are a pinched wire, corrosion or water in
the connector or a faulty turn stalk switch.

Report Date: 11/16/2024 4:29:54PM 7/7