EVO-STIK Gripfill
A HIGH PERFORMANCE, MULTI-PURPOSE, GAP FILLING ADHESIVE
Date: 4 November 2015 Fact Sheet No.: TDS00238
YOUR SMART ADVANTAGES Storage/Shelf Life Store for up to 12 months from date
of manufacture when stored in the
Bonds almost any surface original, unopened packaging under
dry conditions within the
Excellent strength including vertical applications temperature range of +5°C to +25°C.
Suitable for interior and exterior use (provided bond is TYPICAL PERFORMANCE DATA (Approx.)
covered)
Application +5°C to +25°C
USES Temperature
EVO-STIK Gripfill is a solvent-borne, filled rubber resin
adhesive, developed to bond a large variety of rigid materials Service Temperature -30°C to +70°C
together, regardless of the evenness of the surface.
Coverage 350ml: 12 metres of 6mm bead per
EVO-STIK Gripfill is specially formulated to bond a large 350ml cartridge (normally sufficient
variety of materials such as: plywood, blockboard, chipboard, for one 2,440mm x 1,220mm panel)
hardboard, laminated plastics, rigid uPVC, rigid PU insulation
310ml: 11 metres of 6mm bead per
materials, metal sheeting (including aluminum, steel,
310ml cartridge
galvanized iron, tin plate and nonferrous metals) to each
other (as long as one surface is porous) or to brick, stone,
breeze block, sand/cement screeds, concrete, plaster,
plasterboard and insulation boards. DIRECTIONS FOR USE
IMPORTANT: Before using EVO-STIK Gripfill refer to the
It is suitable for bonding aluminium and uPVC stair nosings, relevant Health & Safety Data Sheet, available at
carpet edging strips, carpet grippers, building boards, timber www.bostik.co.uk.
battens, to stairs, floor boards and walls.
PREPARATION
1. All surfaces must be clean, dry and free from dust,
For bonding wall signs, window frames, sink units, fitted
grease and other loose material.
furniture (including light fittings) to a variety of surfaces; in
the building of home extensions. 2. All paints should be removed from surfaces where the
adhesive will make contact.
PRODUCT CHARACTERISTICS
3. Metal surfaces, such as stair nosings, should be
degreased with detergent and water or an appropriate
Form Gunnable paste
degreaser.
Specific Gravity 1.15 approx. 4. New concrete and plaster should be allowed to dry fully
before using EVO-STIK Gripfill.
Product Codes 30812115 310ml x 12 cartridges
30812111 350ml x 12 cartridges
Bostik Limited, Common Road, Stafford, ST16 3EH, UK. Tel: +44 (0) 1785 272625 www.bostik.co.uk
Bostik, Evo-Stik & Sealocrete are registered trademarks of Bostik Ltd.
Page 1 of 3
5. Porous surfaces such as plaster and fibre cement board, Impervious Materials:
should first be primed with Bostik PVA (diluted 1 : 5 with 19. Where two impervious materials are to be bonded, apply
clean water) and allowed to dry thoroughly before EVO- EVO-STIK Gripfill as above, press firmly together and
STIK Gripfill is applied. Building panels should be cut to break the bond pulling away immediately ensuring good
shape beforehand. transfer has occurred. Wait for a maximum of 5 minutes
and re-bond the two materials, or heavy panels.
APPLICATION
6. Fix the cartridge into the extruder. Cut the nozzle to the Battens:
desired width and angle and push a nail through the 20. Apply EVO-STIK Gripfill in 5 - 6mm beads to the back of
nozzle to break the seal at the base. the battens and, using a twisting action, press them
onto the wall. The battens should be fixed vertically at
7. Best results are achieved by applying beads of EVO-STIK 400mm (or closer) intervals with horizontal battens top
Gripfill onto one surface only. and bottom, depending on the weight to be supported.
8. Apply a 6mm diameter “zig-zag” bead along the length CLEANING
of the item to be bonded. 21. Uncured adhesive may be removed using cloths lightly
moistened with white spirit, after carefully scraping off
9. On large panels apply bead around the edge and across the bulk.
the panel at approximately 400mm intervals.
22. Cured adhesive can only be mechanically removed i.e.
10. Then using a twisting action, press the other surface cutting, sanding, scraping.
into position to maximize surface contact and grab.
Press surfaces together firmly for 30 seconds. PRECAUTIONS IN USE
11. Some support may be necessary for up to 24 hours. Where EVO-STIK Gripfill is used externally it must be
protected from driving rain, ponding water or permanently
12. Cold, damp conditions or thick layers of adhesive will wet situations. This can be achieved by using a suitable
greatly extend drying times silicone sealant. EVO-STIK Gripfill is not recommended for
bonding mirrors, as it may cause an adverse reaction on the
Stair Nosings, Window Frames etc.: mirror backing. Do not use EVO-STIK Gripfill in contact with
bitumen. It is not suitable for use on solvent sensitive
13. Apply a continuous bead (usually 6mm in diameter) to
surfaces such as expanded polystyrene, and cellulose paint,
the surface being bonded. Position on the substrate, if
etc. EVO-STIK Gripfill may not be suitable for certain types of
possible by sliding into place, and apply pressure overall.
structural work. EVO-STIK Gripfill will not bond Polythene,
If the object is to be applied to a vertical surface,
Polypropylene, Polyethylene plastics, Teflon (PTFE) or
temporary mechanical support (e.g.: panel pins, masonry
silicone rubber.
nails, etc.) may be required.
For any application not covered please contact Technical
14. Allow to dry overnight prior to any further operation
Services on +44 (0)1785 272625 or visit www.bostik.co.uk for
e.g. fixing boards to battens etc.
advice.
15. Excessive thickness of adhesive may extend drying time.
Recommendations and suggestions are for guidance only,
since conditions of use are completely beyond our control.
16. EVO-STIK Gripfill sets by the evaporation of the solvent
it contains, so drying time is dependent on temperature
For health and safety instruction, first aid measures and
and the nature of the materials being bonded.
spillage and disposal instructions, see separate Health and
Safety Data Sheet for EVO-STIK Gripfill, available at
Wall Panels:
www.bostik.co.uk.
17. For most work, EVO-STIK Gripfill should be applied as a
6mm diameter bead to the rear of the panel. Extrude a
continuous bead around the panel approximately 25mm
from the edge. Additional beads should then be applied
across the panel at 600mm centres (450mm for heavy BOSTIK HOTLINE
panels).
18. Immediately present the panel to the wall slightly above Smart help +44 (0) 1785 272625
its required position and applying pressure slide it into
place in order to break any surface skin. Press firmly to
ensure maximum overall contact, using a soft mallet if
necessary. Continue as above with further panels
making sure they are flush with each other. Any
adjustment must be made within 5 minutes of placing.
Bostik Limited, Common Road, Stafford, ST16 3EH, UK. Tel: +44 (0) 1785 272625 www.bostik.co.uk
Bostik, Evo-Stik & Sealocrete are registered trademarks of Bostik Ltd.
Page 2 of 3
This disclaimer is issued by Bostik Limited ("the Company") and applies to the use of any products supplied by the
Company ("the Products") displayed on this Technical Data Sheet (“TDS”). Please read this disclaimer carefully before
using any of the Products. Using this TDS and/or the Product constitutes your acceptance of this disclaimer. Its
contents shall prevail over any directions of use and any disclaimer and/or exclusion or limitation of liability of the
Company which may appear on the packaging of the Products.
This disclaimer sets out the entire financial liability of the Company (including any liability for the acts or omissions of
its employees, agents and sub-contractors) to any user of the Products ("Product User") in respect of any use made or
resale by the Product User, of any of the Products in this TDS.
This disclaimer does not affect the Company's liability for death or personal injury arising from the Company's
negligence in respect of the Products, nor its liability for fraud, or fraudulent misrepresentation, nor any other
liability which cannot be excluded or limited under applicable law.
The Company's total liability however arising and whether caused by tort (including negligence and breach of
statutory duty), breach of contract or otherwise, arising in connection with the use made or resale by the Product
User of any of the Products in this TDS shall be limited to the price paid for the Product by the Product User.
The Company shall not be liable to the Product User for any pure economic loss, loss of profit, loss of business,
depletion of goodwill or otherwise, in each case whether direct, indirect or consequential, or any claims (including in
respect of personal injury insofar as not caused by the Company's negligence) for consequential compensation
whatsoever (howsoever caused) which arise out of or in connection with the use made or resale by the Product User
of any of the Products in this TDS.
The Company shall not be liable to the Product User in relation to any loss for any use which is inappropriate or use
which is otherwise than in accordance with the relevant instructions for use of the Products in this TDS or on the
Product. Product Users are advised to confirm the suitability of the Products by their own tests.
This TDS covers just one of a large range of products supplied by the Company.
Full information on these products and advice on application is freely available from our fully trained staff
throughout the country. In addition, specialist technical advice is available from our Technical Services Department.
This TDS supersedes all previous TDSs relating to the Products, and users of it must ensure that it is the current issue.
Destroy all previous TDS, and if in any doubt, contact the Company, quoting the code number in the top right hand
corner on the front of this document.
Sales Tel: 0844 371 1192 Fax: 01785 241818 [email protected]
Technical Advice Tel: 0844 371 1197 Fax: 01785 272867
[email protected]Technical Data & COSHH (MSDS) Data Sheets Tel: 01785 272625 Fax: 01785 212962
[email protected] Bostik Limited, Common Road, Stafford, ST16 3EH, UK. Tel: +44 (0) 1785 272625 www.bostik.co.uk
Bostik, Evo-Stik & Sealocrete are registered trademarks of Bostik Ltd.
Page 3 of 3
