Scribd
Upload
3 views

Water Monitoring Syst

The document outlines a project focused on developing a low-cost renewable energy source through a footstep power generator, which captures energy from walking or running. It also includes a water quality monitoring system that utilizes the generated power to assess water parameters like pH and turbidity. The project details the necessary hardware and software components, including sensors, Arduino, and circuit simulation software.

Uploaded by

Muskan Bura
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3 views

Water Monitoring Syst

The document outlines a project focused on developing a low-cost renewable energy source through a footstep power generator, which captures energy from walking or running. It also includes a water quality monitoring system that utilizes the generated power to assess water parameters like pH and turbidity. The project details the necessary hardware and software components, including sensors, Arduino, and circuit simulation software.

Uploaded by

Muskan Bura
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

BY : HIMANSHI

JHANVI SRI(2020/69)
MISHIKA VERMA
MUSKAN(2020/83)
INTRODUCTION
As the availability of Conventional energy declines there is a need to find
alternate energy source and thus non conventional energy system is very
essential in today's time. This project aims to develop a source of renewable
energy with low cost budget. The footstep power generator system is to
capture typically wasted energy surrounding a system and transforming it into
electrical energy which one by simply walking/running as input source.
In addition to that we know that water is one of the basic needs of human
survival , its required to incorporate some mechanism to monitor it's quality
from time to time. Hence there is necessity to ensure that quality of water
supplied is standardized . So we are detecting the quality of water by various
parameter like pH and turbidity as it's application.
HARDWARE REQURIEMENTS
1. FORCE SENSOR:
Force Sensor is also known as load cell or weight sensor. They are
used to measure compression , force , strain etc.
A force sensor is a transducer that converts load ,weight into
electrical signal.It helps in measuring the amount of force applied to
an object . The general working principle of Force Sensors is that
they respond to the applied force and convert the value into a
measurable quantity.
2. MULTIMETER:

A device which can be used to measure either voltage ,current or


resistance.It has two terminals.
3. ARDUINO UNO:
Arduino board is a microcontroller that is used to accept inputs
from sensors connected and provide an output action on the
desired device connected to it. The sensor inputs can be from light-
detecting sensors, motion sensors (Ultrasonic or IR), temperature
sensors, etc. The output from this device can be received through
other output devices such as LED, Buzzer, Serial monitor, etc.
4. BREADBOARD:

Breadboard is the basic component of any circuit building process. All


components, be it input sensors or output display devices are connected to the
power supply, microcontroller using wired connections through a breadboard.
The holes in the breadboard are in series. There are
various sizes like full-sized, half sized, and mini
breadboard.in it holes , above and below row, are
connected horizontally And in middle two rows holes are
connected horizontally.
5. RESISTORS:

Resistors are passive devices that restrict the flow of current or


divide the voltage through the circuit. The input power passes
through these resistors and then to the sensors to avoid
damage.
SOFTWARE REQUIREMENTS
TINKERCAD Circuit Simulation Software :

It is an online simulation software used for circuit design. It has all the
electrical components required to build circuits and runs them.
Block PART 1 :Power generation using foot steps
Diagram
AC
Piezoelectric Bridge
plate Rectifier

DC

Battery
Multimeter Storage

LCD Arduino
Display UNO
Proposed system
Force sensor responds
to the applied force and
provides feedback
Piezo Plate Alternate-
converting the pressure
Force Sensor into a measurable
quantity.
The feedback will be
connected to Arduino
The output can be
harnessed and dispalyed
on the LCD screen.
Block PART 2 :Water Quality Monitoring using Power
Diagram generated by footsteps.

SENSORS
L.C.D.
(temp., other ARDUINO
quality UNO(MCU) (Output)
analyzers)

Power
Generated
using
footsteps.
EXPLAINATION:
Power Generated from Footsteps( from part1 of
our project) ,further will be used in Water Quality
Monitoring System. Power will be transferred to
ardunio ; and once the circuit is complete, results
will be dislayed on L.C.D. screen.
REFERENCES:
FOR POWER GENERATION USING FOOTSTEPS:
1. https://nevonprojects.com/design-fabrication-of-mechanical-footstep-power-generator/
2.https://www.elprocus.com/footstep-power-generation-system/
3.https://youtu.be/PMQYpgo7W7Q
4.https://youtu.be/4nbBAG-848c
5.https://www.annalsofrscb.ro/index.php/journal/article/view/5005/3999
FOR WATER QUALITY MONITORING SYSTEM:
1.https://youtu.be/PMQYpgo7W7Q
THANK
YOU

You might also like