EPON OLT FD1002S CLI User Manual

(V1.2)

Shenzhen C-Data Technology Co., Ltd.

www.cdatatec.com

1
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Contents

1. Preface......................................................................................................................................5
1.1. Introduction..............................................................................................................5
1.2. Definition...................................................................................................................5
2. Configuration Preparation........................................................................................................6
2.1. Management Model.................................................................................................6
2.2. Console Port Connection...........................................................................................6
2.3. Network Connection.................................................................................................7
2.4. User Login EPON CLI System.....................................................................................7
3. Command Format Illustration...................................................................................................8
3.1. Command Format.....................................................................................................8
3.2. Typical Parameter Category......................................................................................9
4. System Root Directory............................................................................................................11
4.1. Enable System Log Printed to Super Terminal.........................................................11
4.2. System Debug Mode...............................................................................................12
4.2.1. debug..............................................................................................................12
4.2.2. dump...............................................................................................................12
4.2.3. log-lvl...............................................................................................................13
4.3. Enable Mode...........................................................................................................13
4.3.1. Switch Control Module MAC Address Management.......................................14
4.3.1.1. Configure switch control module’s MAC Aging Time.......................14
4.3.1.2. Show switch control module’s MAC Address List............................14
4.3.2. Port mirror Management................................................................................14
4.3.2.1. Mirror Destination Port...................................................................14
4.3.2.2. Add Mirror Source Port...................................................................15
4.3.2.3. Delete Mirror Source Port...............................................................15
4.3.2.4. Clear Mirror Source.........................................................................15
4.3.3. Network Configuration Mode.........................................................................16
4.3.3.1. Configure Management Port’s IP and Sub Mask.............................16
4.3.3.2. Configure NMS Port Gateway..........................................................17
4.3.4. OLT Management Mode..................................................................................17
4.3.4.1. Enter OLT Management Mode........................................................17
4.3.4.2. Enable OLT.......................................................................................18
4.3.4.3. OLT Bridge Configuration.................................................................18
4.3.4.4. Restore PON Default Setting............................................................20
4.3.4.5. Link Management Mode.................................................................21
4.3.4.6. ONU Management Mode................................................................27
4.3.4.7. Configure Link ID Overwrite Function.............................................40
4.3.4.8. Configure ONU ID Overwrite Function............................................40

www.cdatatec.com 2 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.9. Reboot PON Card.............................................................................40

4.3.4.10. Save PON card configuration...........................................................41
4.3.4.11. Show OLT’s Basic Information..........................................................41
4.3.5. Configure Enable Password Management......................................................41
4.3.6. RSTP Configuration Mode...............................................................................42
4.3.6.1. Configure RSTP Bridge Parameter...................................................42
4.3.6.2. Enable RSTP Function......................................................................43
4.3.6.3. Disable RSTP Function.....................................................................44
4.3.6.4. Hold Bridge Forwarding Frame Count.............................................44
4.3.6.5. Configure RSTP Port Parameter.......................................................44
4.3.6.6. Show RSTP Configuration Information............................................46
4.3.7. Configure switch control module’s Switching Mode.......................................47
4.3.7.1. Set Private Vlan Mode.....................................................................47
4.3.7.2. Show switch control module’s Switch Mode Configuration............47
4.3.7.3. Enable switch control module’s Vlan Function................................47
4.3.8. Uplink Port Management mode of switch control module.............................48
4.3.8.1. Set Port’s RX Frames Types..............................................................49
4.3.8.2. Set Port’s Default Priority Level.......................................................49
4.3.8.3. Configure Port’s Duplex Mode........................................................49
4.3.8.4. Enable Port......................................................................................50
4.3.8.5. Disable Port.....................................................................................50
4.3.8.6. Configure Port’s Flow Control Mode...............................................50
4.3.8.7. Set Port’s RX Filter Function............................................................50
4.3.8.8. Configure Port Mode.......................................................................51
4.3.8.9. Enable Port’s Nest-Vlan Function....................................................51
4.3.8.10. Enable Port’s Protocol Vlan.............................................................51
4.3.8.11. Set Port’s PVID.................................................................................52
4.3.8.12. Configure Port’s Rate Limits............................................................52
4.3.8.13. Configure Port’s Reauto-Negotiation Function................................52
4.3.8.14. Show Port Information....................................................................52
4.3.8.15. Configure Port’s Compulsive Shutdown Function...........................53
4.3.8.16. Remove Compulsive Shutdown Port...............................................53
4.3.8.17. Configure Current Port Rate............................................................53
4.3.9. System Configuration Mode............................................................................54
4.3.10. Synchrony with ONU Configuration................................................................54
4.3.10.1. Backup EPON System Configuration................................................55
4.3.10.2. Restore EPON System Configuration...............................................55
4.3.10.3. Configure Console Port Speed.........................................................55
4.3.10.4. ONU Authorization Management Mode.........................................56
4.3.10.5. Set SNMP Read Community............................................................58
4.3.10.6. Reboot OLT......................................................................................58
4.3.10.7. Restore Default Configuration and Reboot Equipment...................59
4.3.10.8. Save Current Configuration.............................................................60
4.3.10.9. Set Trap Receiving IP Address..........................................................60

www.cdatatec.com 3 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.10.10. Set SNMP Written Community........................................................60

4.3.11. Trunk Management Mode...............................................................................61
4.3.11.1. Configure Trunk Balance Algorithm.................................................61
4.3.11.2. Delete Trunk Group.........................................................................62
4.3.11.3. Add Trunk Member.........................................................................62
4.3.12. Show Trunk Configuration Information...........................................................62
4.3.13. User Management...........................................................................................63
4.3.13.1. Set User Authority...........................................................................63
4.3.13.2. Add User..........................................................................................63
4.3.13.3. Delete User......................................................................................63
4.3.13.4. Change User Password....................................................................64
4.3.13.5. Show Current User’s Information....................................................64
4.3.13.6. Change User’s Timeout...................................................................64
4.3.14. VLAN Management Mode...............................................................................65
4.3.14.1. Delete Vlan Member.......................................................................65
4.3.14.2. Delete Vlan......................................................................................66
4.3.14.3. Add Vlan Member Port list..............................................................66
4.3.15. Show Vlan Configuration Information.............................................................66
4.4. Show System Running Information.........................................................................68
4.4.1. Show System’s Current CPU Running Status...................................................68
4.4.2. Show System’s Memory Use Status.................................................................68
4.4.3. Show System’s Task Status..............................................................................69
4.4.4. Enable CATV (RF) Function..............................................................................69
4.4.5. disable CATV (RF) Cut-Off Function.................................................................70
4.5. Global Command.....................................................................................................70
4.5.1. Create Command Alias....................................................................................70
4.5.2. Change Directory.............................................................................................70
4.5.3. Clear Screen....................................................................................................70
4.5.4. Copy File..........................................................................................................71
4.5.5. Show System’s Date.........................................................................................71
4.5.6. Delete File.......................................................................................................71
4.5.7. Exit From The Current Command Mode.........................................................71
4.5.8. Return to System Main Directory....................................................................72
4.5.9. Help.................................................................................................................72
4.5.10. Command History............................................................................................72
4.5.11. Log Out System................................................................................................72
4.5.12. Show Current File List......................................................................................72
4.5.13. PING................................................................................................................73
4.5.14. Show Directory Route.....................................................................................73
4.5.15. TFTP.................................................................................................................73

www.cdatatec.com 4 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

1. Preface

1.1. Introduction

C-Data OLT FD2000S system could support inband and outband network management mode and
EMS network management based on SNMP ，which we would provide our EMS software along
with the parcel for shipping .Besides, we could also support CLI management for user to get
access to our EPON system with more option. Herein ,we would like to introduce our CLE user
manual .However ,we would still highly recommend users to use our EMS management to
monitor and configure the whole EPON system via EMS since we have offered very powerful
function and simple operation in the EMS interface .

1.2. Definition

Product/ Description
Abbreviation
EPON Gigabit Ethernet Passive Optical Network
OLT Optical Line Terminal
ONU Optical Network Unit

www.cdatatec.com 5 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

2. Configuration Preparation

2.1. Management Model

2.2. Console Port Connection

There is a Console port in the front panel of switch control module .The command line
configuration interface is enabled via console port connecting to the NMS’s superior
terminal .Super terminal’s basic configuration is as follows :

www.cdatatec.com 6 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

2.3. Network Connection

FD2100S support inband management (CAT5 connect to ge1-ge8 port) and outband management
(CAT4 cable to management port).After Telnet to CLI interface ,we can manage the EPON
products.

Defualt outband network management IP:192.168.120.100

Default inband network management IP: 192.168.1.100

2.4. User Login EPON CLI System

System provide two login accounts default as follows:

User Password
admin Admin
guest Blank
After you log in successfully, the following interface pops up :

********************************************************************

www.cdatatec.com 7 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Command Line Interface for EPON System

Hardware Ver: OLT-0.2
Software Ver: OLT-1.5.2
Created Date: Sep 30 2013 17:02:11
Copyright (c) 2006-2012 . All rights reserved.
********************************************************************
Login:admin
Password:
epon>
When the command lines shows : epon> ,user can input the configuration command to mange
or inquire the configuration information .

3. Command Format Illustration

3.1. Command Format

1 Command Conventions
2 Keyboard Operation Conventions
3 Symbols

Convention Description
Used to highlight the key words (inportant words
Boldface
that should never be modified when input).
Used to denote the parameters that should be
italic replaced by actual values when practical use in
command line.
Items(keywords or arguments) in square brackets [ ]
[]
are optional.
Alternative items are grouped in braces and
(x | y | ... )
separated by vertical bars. One is selected.
Optional alternative items are grouped in square
[x|y|…] brackets and separated by vertical bars. One or
none is selected.
<x-y> Values range from x to y. One is selected.
$ A line starting with the $ sign is comments.

Format Description

www.cdatatec.com 8 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

<key> Press the key with the key name inside angle
brackets. For example, <Enter>, <Tab>,
<Backspace>, or <A>.
<key1 + key2> Press the keys concurrently. For example,
<Ctrl+Alt+A> means the three keys should be
pressed concurrently.
<key1, key2> Press the keys in turn. For example, <Alt, A> means
the two keys should be pressed in turn.

Eye-catching symbols are also used in the manual to highlight the points worthy of
special attention during the operation. They are defined as follow:

Caution: Means reader be extremely careful. Improper operation may cause

data loss or damage to equipment

Warning: Means reader be extremely careful. Improper operation may cause

bodily injury.

Note: Means a complementary description.

4. Hints Commands in this mannual is case sensitive.

3.2. Typical Parameter Category

When configure the system with CLI(command lines) ,we will meet with some data types with
fixed format ,which embody some index’s meaning ,expression mode and value range.

Herein,we list some repeated commands to explain their meaning and use.

vlanid Vlan index with valid integer value from 1 to 4094 .

Port number including gigabitethernet ports from 1 to 6, short for ge1

to ge6 . To mention that ge5 to ge6 can’t be seen, corresponding
port with 2 PON ports .We can say that ge5~ge6 is for PON1-PON2
configuration. While ge1~ge4 is for switch control modul’s 4 uplink
port configuration.

portlist Port list such as “ge1,ge5”( 2 ports) ,”ge1-ge5”(meaning 5 ports from

www.cdatatec.com 9 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

ge1 to ge5.)

Ip port name includes inband and outband.inband interfaces is

embodyed with vi+number (vi means virtual interface).for example:
“vi0” means the first inband IP interface(it’s the only one interface to
ifx-name support inband ip interface.);outband interface is embody with
“cpm+number”.cpm is the outband interface’s device name .For
example, cmp0 means the first outband ip nterface .(this is the only
one interface to support outband ip interface .)

ip-addr Ip address such as 192.168.1.1

ip-mask Ip mask with 4 segments of algorism bytes ,such as 255.255.255.0

mac MAC address such as 00:01:02:02:04:05

moduleId Module ID number

moduleId module name
3 common mbuf pool
4 HDLC driver
5 inter-board communicaiton protocol
9 device online status maintenance
10 system basic configuration
11 user manager
12 switch port attribute management
13 switch port status poll task
14 switch port statistics poll task
15 trunk module
16 mirroring module
17 normal vlan module
18 protocol type based VLAN
19 rapid spanning tree module
20 IP network interface
21 misc configuration on switch card
22 ONU base manage configuration
23 ONU advanced manage configuration
24 ONU UNI port configuration
25 ONU Queue configuration
26 ONU ACL Rules configuration
27 ONU port VLAN configuration
28 ONU authentication
29 ONU port QoS configuration
30 ONU IGMP Snooping configuration
31 ONU loopback test configuration
32 ONU dynamic mac table configuration

www.cdatatec.com 10 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

33 Extern network management module

34 OLT basic configuration
35 OLT advanced configuration
36 OLT bridge configuration
37 OLT DBA configuration
38 OLT aggregate bandwidth configuration
39 OLT acl rules configuration
40 OLT priority copy mapping configuration
41 OLT IGMP configuration
42 OLT PPPOE configuration
43 Logical Link basic configuration
44 Logical Link advanced configuration
45 Logical Link SLA configuration
46 Logical Link VLAN configuration
47 Logical Link blocked link configuration
48 Logical Link dynamic and static MAC
50 on-line upgrade module
51 port statistics alarm and threshold

4. System Root Directory

Ater you log in successfully , input “？”or “help”to show the current directory
epon> ?
[no] copy-log - print log messages on the current shell.
debug - enter debug mode
enable - enter privileged mode
exe - Execute raw commands(global C functions).
show - show various parameters

4.1. Enable System Log Printed to Super Terminal

Command [epon>[no] copy-log

www.cdatatec.com 11 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Grammar

Function Show current System Log

4.2. System Debug Mode

Command
epon>debug
Grammar

Function enter debug mode ，

【Remark】

entering“exit”could return to the current mode .

You will find the command as follows after entering debug mode :

epon% ？ input “？”or “help”to show the current directory

debug - debug specific module
dump - show module internal data
log-lvl - set log level for specific module

4.2.1. debug

Command
epon%debug module <moduleId>
Grammar

Function Configure the module’s debug functions

【Remark】

This command isn’t valid yet .

www.cdatatec.com 12 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.2.2. dump

Command
epon%dump module <moduleId>
Grammar

Function Configure the module’s dump functions

<moduleId> Module ID ,format please refer to 3.3 typcial Parameter category

4.2.3. log-lvl

Command
epon%Log-lvl module <moduleId> <level>
Grammar

Function Change module’s LOG level

Module ID ， definition format refer to typical Parameter category

<moduleId>
illustration .

There are 5 level for LOG level, marked from 0 to 4 .0 is the highest
level.
0:critical event
<level> 1:important event
2:general event
3:trivial event
4:debug message

4.3. Enable Mode

Command
epon>enable
Grammar

Function Enter “enable management mode and provides enable password.

【Example】

1. enter enable management mode:

epon>enable

www.cdatatec.com 13 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

password:
epon#

The default password to enter enable mode is admin.

epon# ？ Input“？” or “help”to show the follwing directory:
igmp-snooping - configure global IGMP Snooping
mac-address - ctrl-card dynamic mac address table management
mirror - mirroring configuration
network - configure network parameters
olt - enter olt config mode
passwd - change enable password
rstp - enter rapid spanning tree config mode
show - dislpay configuration
swmode - set basic switch mode
swport - enter switch port config mode
system - configure system basic parameters
trunk - enter trunk config mode
user - User configuration
vlan - enter vlan config mode

4.3.1.Switch Control Module MAC Address Management

4.3.1.1. Configure switch control module’s MAC Aging Time

Command
epon#mac-address aging <timeout>
Grammar

Function Configure switch control module’s MAC address aging time

MAC aging time ,with value range from 0 to 255.step length is 15

<timeout>
seconds.

4.3.1.2. Show switch control module’s MAC Address List

Command
epon#mac-address show
Grammar

Function Show switch control module’s MAC address list.

www.cdatatec.com 14 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.2.Port mirror Management

4.3.2.1. Mirror Destination Port

Command
epon#mirror destination port < port >
Grammar

Configure the designated port for the switch control module as the
Function
mirror destination port

Designate a port as the mirror destination port with value range from
< port >
gel to ge4.

4.3.2.2. Add Mirror Source Port

Command
epon#mirror source add port < portlist > < direction >
Grammar

Configure added mirror source port ,available for designating some

Function
port’s uplink ,downlink or bidirectional data flow as mirror source .

Designate some port as mirror source port .Designation means could

< port list>
refer to 3.3 Typical Parameter category Illustration.

Designate mirror source’s data flow direction with vale as follows:

ingress
< direction >
egress
both

4.3.2.3. Delete Mirror Source Port

Command
epon#mirror source delete port < portlist > < direction >
Grammar

Delete mirror source port ,which could appoint one direction’s data
Function
flow as mirror source .

< port list> Port list

< direction > Appoint deleted mirror sour’s data flow direction:
ingress

www.cdatatec.com 15 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

egress
both

4.3.2.4. Clear Mirror Source

Command
epon#mirror source clear
Grammar

Function Clear all mirror source including all source port and source VLAN.

4.3.3.Network Configuration Mode

Command
epon#network
Grammar

Function Configure inband and outband management port’s IP address.

【Example】

1.Enter network management mode

epon#network
epon(net)#

epon(net)# input“？”or “help”to show the following directory

[no] address - set network interface address
[no] gateway - configure network default gateway

4.3.3.1. Configure Management Port’s IP and Sub Mask

Command
epon(net)#address <ifx-name> <ip-addr> <ip-mask>
Grammar

Function Configure network port’s IP address and submask. Currently our

network management port includes inband network management

www.cdatatec.com 16 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

port vi0 and outband network management port cpm0. input

address <ifx-name> could show the current networking
configuration.

Appointed ip port name ,which could be vi0 or cpm0 ,port format

< ifx-name>
expression mode refer to typical Parameter category.

<ip-add> Configure IP address

< ip-mask > Configure appointed IP address’s network mask.

【Example】

1.Enquiry the current inband network management port’s network configuration:

epon(net)#address vi0
Interface vi0:
Ip address :192.168.1.100
Netmask :255.255.255.0
associated vlan :1
admin status :operational

Example 2:Configure inband management IP as 192.168.1.1 ,mask is 255.155.155.0

epon(net)#address vi0 192.168.1.1 255.255.255.0

Example 3:Configure outband management IP as 192.168.1.2 and mask is 255.255.255.0

epon(net)#address cpm0 192.168.1.2 255.255.255.0

4.3.3.2. Configure NMS Port Gateway

Command
epon(net)#gateway <ip-addr>
Grammar

Configure NMS port’s gateway.

Function
Input command gateway to show the current gateway information.

<ip-addr> Configure the appointed gateway address.

www.cdatatec.com 17 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.OLT Management Mode

4.3.4.1. Enter OLT Management Mode

Command
epon#olt <slotid> <oltid>
Grammar

Enter OLT management mode to configure OLT,downplink and ONU .

Function
just input “olt” could show the current online OLT .

<slotid> olt pon module slot with value 0 .

<oltid> Pon ID with valid value 1 and 2 .

【Example】

1.Show current online OLT :

epon#olt
Following is online olt list:
Slot Olt Mac Address Online Status
0 1 00:a1:02:01:03:40 Online
0 2 00:a1:02:01:03:40 Online

2. Manage PON-1 .
epon#olt 0 1
epon(slot0-olt1)#

epon(slot0-olt1)# ？ input“？”or “help” to show the command directory :

admin - set olt administrate status
bridge - set olt bridge configuration
default - reset olt default configuration
ext-mgmt - extern network management
factory - Restore factory settings,onuid will be redistributed.
link - enter link config mode
onu - enter onu config mode
overwrite-linkid - overwrite linkid when linkid is exhausted
overwrite-onuid - overwrite onuid when onuid is exhausted
p2p - onu p2p management
restore - restore to saved configuration
save - save pon card configuration
show - show olt base configuration

www.cdatatec.com 18 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.2. Enable OLT

Command
epon(slot0-olt1)#admin <enable | disable>
Grammar

Function Enable/disable OLT

<enable> Enable OLT

<disable> Disable OLT

4.3.4.3. OLT Bridge Configuration

Command
epon(slot0-olt1)#bridge
Grammar

Function Show current bridge setting

【example】

1. Show OLT’s current bridge setting

epon(slot0-olt1)#bridge
Bridge Configuration:
learned mac age limit :0 (ms)
bridge vlan number :64 (bridges)
allow simple bridge :YES
mac learn overwrite :NO
discard unknown mac :NO
allow tagged frame :YES

4.3.4.3.1. MAC Address Aging Time

Command
epon(slot0-olt1)#bridge limit <limit>
Grammar

Change MAC address’s aging time .0 means not to learn MAC , the
Function
unit is 1ms .

<limit> Parameterrange 0-2419200

www.cdatatec.com 19 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.3.2. Bridge VLAN Number Configuration

Command
epon(slot0-olt1)#bridge vlan-num <vlanNum>
Grammar

Function Set bridge vlan number(tk3723 chipset OLT ‘s fixed number is 64)

<vlanNum> Fix number is 64

4.3.4.3.3. MAC Address Overwrite Configuration

Command
epon(slot0-olt1)#bridge overwrite <enable | disable>
Grammar

Function Set overwrite MAC address mode

Parameters <enable|disable> with the meaning as follows:

enable:When MAC address is full ,new MAC overwrite existing
<enable | disable>
MAC address .
disable:When MAC address is full ,ignore the new MAC address .

4.3.4.3.4. Unknown MAC Restriction Configuration

Command
epon(slot0-olt1)#bridge dsc-unk-mac <enable | disable>
Grammar

Function Set unknown MAC restriction mode

enable:unknown DA downlink packet deliver the broadcast to all

<enable | disable> ports .
disable:unknown DA downlink packet is abandon

4.3.4.3.5. Forward Tag Frame Configuration

Command
epon(slot0-olt1)#bridge tag-on-sbrg <enable | disable>
Grammar

Function Set tag forwarding rules under simple bridge mode.

enable:allow forwarding tag frame

<enable | disable>
disable:dump tag frame

www.cdatatec.com 20 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.4. Restore PON Default Setting

Command
epon(slot0-olt1)#default
Grammar

Restore PON Default Setting

Function

【Remark】

The command will delete PON module’s all setting and restore the ex-factory default setting .And
the PON module will reboot automatically.

4.3.4.5. Link Management Mode

Command
epon(slot0-olt1)#link <linkid>
Grammar

Function Enter LINK management mode and configure link Parameter.，

<linkid> Designated linked with value range from 1 to 256 .

【Example】

1.Show the current LINK :

epon(slot0-olt1)#link
Following is link list:
Link Id Mac Address Online Status
1 00:a1:02:01:07:30 Online
2 00:a1:02:01:07:31 Offline
3 00:a1:02:03:bc:f8 Offline
4 00:a1:02:01:97:d0 Offline
5 e0:67:b3:03:be:e8 Offline
6 00:a1:02:04:e7:08 Offline
7 00:a1:02:01:07:38 Online
8 00:a1:02:01:07:39 Online

2.Enter Link1 management interface :

epon(slot0-olt1)#link 1
epon(slot0-olt1-link1)#

epon(slot0-olt1-link1)# ？ input“？”or “help”to show command directory:

[no] block - block link

www.cdatatec.com 21 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

bridge-mode - only support simple-bridge mode now.

dynamic-mac-clear - clear dynamic mac table
dynamic-mac-list - display all dynamic mac table
dynamic-mac-refresh - refresh dynamic mac table
rediscover - force link rediscovery
show - show link basic configuration
sla - set link SLA parameters
static-mac-add - add a static mac
static-mac-del - delete a static mac
static-mac-list - display all static mac table

4.3.4.5.1. Block Current Link

Command
epon(slot0-olt1-link1)#block
Grammar

Function Block current link to stop the link’s data flow.

4.3.4.5.2. Remove the Current Link Block

Command
epon(slot0-olt1-link1)#no block
Grammar

Function Remove the current link block to restore the link’s data flow.

4.3.4.5.3. Clear Link’s Dynamic MAC Address List

Command
epon(slot0-olt1-link1)#dynamic-mac-clear
Grammar

Function Clear link’s dynamic MAC address list

4.3.4.5.4. Show Link’s Dynamic MAC Address List

Command
epon(slot0-olt1-link1)#dynamic-mac-list
Grammar

Function Show all the MAC address list learned from the link

www.cdatatec.com 22 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

【Remark】

Please use the command “ dynamic-mac-refresh” to refresh the link’s dynamic MAC address
before showing the link’s dynamic MAC address .

4.3.4.5.5. Refresh Link’s Dynamic MAC Address List

Command
epon(slot0-olt1-link1)#dynamic-mac-refresh
Grammar

Function Refresh link’s dynamic MAC Address

4.3.4.5.6. Force Rediscovering Link

Command
epon(slot0-olt1-link1)#rediscover
Grammar

Function Force the link rediscovering to OLT

4.3.4.5.7. Show LINK Basic Information

Command
epon(slot0-olt1-link1)#show
Grammar

Function Show the link’s current basic configuration information

【Example 】

1.Show the current link’s basic configuration information :

epon(slot0-olt1-link1)#show
Link Basic Configurations:
associated onu id :1
assigned link id by olt :0
mac address :00:a1:02:0a:a1:08
online status :Online
key exchange timer :0 (sec)
bridging type :simple-bridge
mac table entry limit :64 (entries)

www.cdatatec.com 23 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

cross connected link id :NO

4.3.4.5.8. Link SLA Configuration

4.3.4.5.8.1.Configure Link’s Minimum Guaranteed Bandwidth

Command
epon(slot0-olt1-link1)#sla <dir> min-bw <min-bw>
Grammar

Configure the link’s uplink or downlink’s minimum guaranteed

Function
bandwidth

Appoint the link sla’s direction :

<dir> downstream
upstream

Appoint the link ‘s minimum guaranteed bandwidth with valid

<min-bw> value from 0,256 to 1000000.
0 means disabling the minimum guaranteed bandwidth function.

【Remark】

The minimum bandwidth much be lower than or equal to the maximum allowed bandwidth .

4.3.4.5.8.2.Configure Link’s Maximum Allowed Bandwidth

Command
epon(slot0-olt1-link1)#sla <dir> max-bw <max-bw>
Grammar

Configure the link’s uplink or downlink maximum allowed

Function
bandwidth .

Appoint the link SLA’s configuration direction :

<dir> downstream
upstream

Appoint the link ‘s maximum allowed bandwidth with valid value

<max-bw> from 256 to 1000000.
0 means disabling the minimum guaranteed bandwidth function.

【Remark】

www.cdatatec.com 24 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

The maximum bandwidth must higher than or equal to the minimum guaranteed bandwidth .

4.3.4.5.8.3.Configure Link Transmission Time Delayed Level

Command
epon(slot0-olt1-link1)#sla <dir> level <level>
Grammar

Function Configure uplink or downlink’s transmission delayed time level.

Two direction Parameter optional :

<dir> downstream
upstream

Appoint downlink or uplink’s transmission delayed time level with

the valid value as follows :
<level>
Sensitive: sensitive service could be given the priority to transmit .
tolerant : non-sensitive service

4.3.4.5.8.4.Configure Link’s Maximum Burst Flow

Command
epon(slot0-olt1-link1)#sla <dir> burst-size <burst>
Grammar

Function Configure uplink or downlink’s maximum burst flow .

Two configuration direction as follows :

<dir> downstream
upstream

Appoint the link ‘s maximum burst flow with the valid value range
<burst>
from 1 to 256.

4.3.4.5.8.5.Show LINK SLA Configuration

Command
epon(slot0-olt1-link1)#sla <dir>
Grammar

Function Show uplink or downlink’s SLA configuration information

downstream or
<dir>
upstream

【Example】

www.cdatatec.com 25 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

1.Show current uplink’s SLA configuration information :

epon(slot0-olt1-link1)#sla upstream
Current Link SLA configuration(Upstream):
minimum guaranteed bandwidth :0 (Kbps)
maximum allowed bandwidth :1000000(Kbps)
delay sensitive :Tolerant
max burst size :100 (KBytes)
sla state :Enable

2.Show downlink’s SLA configuration information :

epon(slot0-olt1-link1)#sla downstream
Current Link SLA configuration(Downstream):
minimum guaranteed bandwidth :0 (Kbps)
maximum allowed bandwidth :1000000(Kbps)
delay sensitive :Tolerant
max burst size :100 (KBytes)
sla state :Enable

4.3.4.5.9. Add Link’s Static MAC Address

Command
epon(slot0-olt1-link1)#static-mac-add <mac>
Grammar

Function Add link’s static MAC address

<mac> Input MAC address

4.3.4.5.10. Delete Link’s Static MAC Address

Command
epon(slot0-olt1-link1)#static-mac-del <mac>
Grammar

Function Delete Appointed Link’s Static MAC Address

<mac> Input the deleted MAC address

4.3.4.5.11. Show Link’s Static MAC Address List

Command epon(slot0-olt1-link1)#static-mac-list

www.cdatatec.com 26 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Grammar

Function Show the link’s static MAC address

4.3.4.6. ONU Management Mode

Command
epon(slot0-olt1)#onu <onuid>
Grammar

Function Enter ONU management mode and configure the ONU Parameter.

<onuid> Input onuid with the valid value range from 1 to 64

【Example】

1.Show current online ONU

epon(slot0-olt1)#onu
Following is online onu list:
slotId oltId onuId deviceType basedMac hWRev fwRev
0 1 1 ONU4D 00:a1:02:01:07:30 V03 Vc2.30
0 1 6 ONU2D-G 00:a1:02:01:07:38 V02 Vc2.42

2. Enter ONU1 management interface

epon(slot0-olt1)#onu 1
epon(slot0-olt1-onu1)#

epon(slot0-olt1-onu1)# ？ input“？”or “help” to show command directory

catv - catv switch configuration
ctc - CTC operations
default - restore to default setting
iadParamCfg - iadParamCfg
info - onu device user information
loopback-test - loopback test
mac-address - onu addresses management
port - enter onu port config mode
port-protect - isolate onu ports
reboot - reboot the system
restore - restore to saved configuration
rstp - onu rapid spanning tree config
save - save onu configuration
user-traffic - enable or disable user traffic
vlan-type - set onu additional vlan ethertype

www.cdatatec.com 27 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.6.1. Restore ONU Default Configuration

Command
pon(slot0-olt1-onu1)#default
Grammar

Function Restore ONU default configuration

【Remark】

The command will delete all ONU’s configuration to restore default configuration .The ONU will
reboot automatically .

4.3.4.6.2. IGMP Snooping Configuration

4.3.4.6.2.1.ONU IGMP Global Parameter Configuration

4.3.4.6.2.1.1. Fast leave enable

Command
epon(slot0-olt1-onu1)#ctc igmp-snooping fast-leave <state>
Grammar

Function Enable /disable fast leave function

enable
<state>
disable.

4.3.4.6.2.1.2. Multicast Switching Mode

Command
epon(slot0-olt1-onu1)#ctc igmp-snooping mode <mode>
Grammar

Function Add a IGMP address and a port number

igmp-mld-snooping
controllable-igmp-mld
igmp-snooping-only
<mode> controllable-igmp
disable
*Only igmp-mld-snooping and disable are valid

www.cdatatec.com 28 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.6.2.2.IGMP Port Configuration

4.3.4.6.2.2.1. Set number of igmp groups for onu port

Command
epon(slot0-olt1-onu1-fe1)#ctc igmp-snooping max-group <groups>
Grammar

Function set number of igmp groups for onu port

<groups> number of igmp groups,<0~64>

4.3.4.6.2.2.2. Set multicast strip mode

Command
epon(slot0-olt1-onu1-fe1)#ctc igmp-snooping tag-handle <mode>
Grammar

Function Set multicast strip mode

not-strip-vlan-tag - Not Strip Vlan Tag

<mode> strip-vlan-tag - Strip Vlan Tag
switch - Switch VLAN tag

4.3.4.6.2.2.3. add igmp-vlan-group list on ONU user port

Command epon(slot0-olt1-onu1-fe1)#ctc igmp-snooping vlan-tag-list

Grammar <vlanTagList>

Function add igmp-vlan-group list at ONU user port

<vlanTagList> - vlan tag list,<Combination of 1~4094, or null>

4.3.4.6.2.2.4. Show multicast setting on ONU user port

Command
epon(slot0-olt1-onu1-fe1)#ctc igmp-snooping show
Grammar

Function Show multicast setting on ONU user port

4.3.4.6.3. Configure ONU User Information

Command
epon(slot0-olt1-onu1)#info <info>
Grammar

Configure ONU user information;

Function
Just input “info” to show the current ONU user’s information .

www.cdatatec.com 29 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

<info> User information bytes with longest bytes 64

4.3.4.6.4. ONU Link Loopback Test

Command
epon(slot0-olt1-onu1)#loopback-test
Grammar

Test ONU link status and this command is interactive command which
need the user to provide the following Parameterstep by step .
loopback location: mac 或 phy
Function
number of frames:1-65535
payload length:64-1500
vlan tag:0-4094

【Example 】

1.Test ONU Link

epon(slot0-olt1-onu1)#loopback-test
please offer the loopback test parameter:
loopback location[mac|phy]:mac
number of frames[1~65535]:100
payload length[64~1500]:64
vlan tag[0~4094]:0
testing...
result:
frames sent :100
frames received :100
corrupted frames receiv :0
minimum Delay (us) :2512
maximum Delay (us) :5788
mverage Delay (us) :4135

4.3.4.6.5. Show ONU Dynamic MAC Address List

Command
epon(slot0-olt1-onu1)# mac-address-show
Grammar

Function Show ONU’s dynamic learning MAC address gloably.

www.cdatatec.com 30 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.6.6. ONU Port Management Mode

Command
epon(slot0-olt1-onu1)#port < uni-port>
Grammar

Enter ONU port management mode and configure the ONU port’s
Function
Parameter.

< uni-port > Appoint onu port number with valid value range from fe1 to fe24.

【Example】

1.Enter ONU1’s port 1 interface

epon(slot0-olt1-onu1)#port fe1
epon(slot0-olt1-onu1-fe1)#

epon(slot0-olt1-onu1-fe1)# ？ input “？”or “help” to show the command directory

attribute - onu port attribute config
bridge - onu port bridge parameter config
ctc - CTC mgmt mode
dynamic-mac-clear - clear dynamic mac table
dynamic-mac-list - display all dynamic mac table
[no] enable - enable onu port
info - set onu port user information
qos - onu port qos config

4.3.4.6.6.1.Configure ONU port’s Parameter Attribute

4.3.4.6.6.1.1. Show ONU Port Parameter

Command
epon(slot0-olt1-onu1-fe1)#attribute
Grammar

Function Show ONU port’s Parameter attribute.

【Example】

1:Show ONU1 ‘s port 1 attribute

epon(slot0-olt1-onu1-fe1)#attribute
ONU(0/1/1) Port fe1 attribute:
auto negotiation :enable
flow control :disable
speed :10m

www.cdatatec.com 31 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

duplex :half

4.3.4.6.6.1.2. Configure ONU Port Auto-Negotiation

Command
epon(slot0-olt1-onu1-fe1)#attribute auto-nego <oper>
Grammar

Function Configure ONU port to be auto-negotiable

Value input is <enable | or disable>:

<oper> enable : enable the port’s auto-negotiation function
disable : Disable the port’s auto-negotiation function

4.3.4.6.6.1.3. Configure ONU Port Speed

Command
epon(slot0-olt1-onu1-fe1)#attribute speed <speed>
Grammar

Function Configure ONU port’s speed

<speed> ONU port speed with valid value as follows:10m，100m，1000m

4.3.4.6.6.1.4. Configure ONU Port’s Duplex Function

Command
epon(slot0-olt1-onu1-fe1)#attribute duplex < duplex>
Grammar

Function Configure ONU port’s duplex status

< duplex> ONU port’s duplex status with value “half” or full

4.3.4.6.6.1.5. Configure ONU Port Flow Control Function

Command
epon(slot0-olt1-onu1-fe1)#attribute flow-ctrl <oper>
Grammar

Function Configure ONU port’s flow control function

Enable/disable ONU port flow control function

< oper> Enable: enable ONU port flow control function
Disable:disable ONU port flow control function

www.cdatatec.com 32 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.6.6.2.Configure ONU port’s Bridge Parameter

4.3.4.6.6.2.1. Show ONU Port Bridge Parameter

Command
pon(slot0-olt1-onu1-fe1)#bridge
Grammar

Function Show ONU port bridge Parameter

【example】

1:Show ONU port-1’s bridge Parameter

epon(slot0-olt1-onu1-fe1)#bridge
ONU(0/1/1) Port fe1 bridge parameter:
automatic learning entry limit :16
learned entry age limit :0s
forwarding mode :802.1d mode

4.3.4.6.6.2.2. Configure ONU Port’s Dynamic MAC Limits

Command
epon(slot0-olt1-onu1-fe1)#bridge < entry-limit>
Grammar

Function Configure ONU port’s dynamic learning MAC number

Maximum learning MAC number with valid value from 0 to 64;0

< entry-limit>
means not to learn MAC address

4.3.4.6.6.2.3. Configure ONU Port’s MAC Aging Time

Command
epon(slot0-olt1-onu1-fe1)#bridge age-time < age-time>
Grammar

Function Configure ONU port’s Aging time of MAC address

MAC address aging time with valid value from 0 to 32768;

< age-time >
0 means not to age MAC address

4.3.4.6.6.2.4. Configure ONU Port’s Forward Mode

Command
epon(slot0-olt1-onu1-fe1)#bridge forward-mode < forward-mode>
Grammar

www.cdatatec.com 33 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Function Configure ONU port’s forward mode

Forward mode with valid value such as 8021d,drop-until-learned;

<forward-mode> 8021d mode :unknown MAC packet broadcast to all ports ;
Drop-until-learned mode: drop unknown MAC packet

4.3.4.6.6.3.Clear ONU Port’s Dynamic MAC List

Command
epon(slot0-olt1-onu1-fe1)#dynamic-mac-clear
Grammar

Function Clear ONU port’s dynamic MAC list

4.3.4.6.6.4.Show ONU Port’s Dynamic MAC List

Command
epon(slot0-olt1-onu1-fe1)#dynamic-mac-list
Grammar

Function Show ONU port’s dynamic MAC List

4.3.4.6.6.5.Enable ONU UNI Port

Command
epon(slot0-olt1-onu1-fe1)#enable
Grammar

Function Enable ONU port to make sure normal communication

4.3.4.6.6.6.Disable ONU UNI Port

Command
epon(slot0-olt1-onu1-fe1)#no enable
Grammar

Function Disable ONU port to stop the data flow communication

4.3.4.6.6.7.Configure ONU Port’s User Information

Command
epon(slot0-olt1-onu1-fe1)#info <info>
Grammar

Function Set ONU port’s user information;

Input “info” to show ONU port’s user information

www.cdatatec.com 34 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

<info> User information bytes length ,with the longest length 64 bytes

4.3.4.6.6.8.Configure ONU Port’s Uplink Speed Limit

Command epon(slot0-olt1-onu1-fe1)#qos ingress-policing < max-rate>

Grammar < traffic-type>

Function Set ONU port’s uplink bandwidth limits.

Input “qos ingress-policing” to show the current uplink speed limit
configuration information .

< max-rate> Maximum uplink bandwidth ;unit :kbps ;valid value:0-100000;

Appoint speed limit’s packet type with value as follows: Broadcast;

broadcastAndMulticast;
< traffic-type>
broadcastMulticastAndFloodedUnicast;
all

4.3.4.6.6.9.Configure ONU Port’s Downlink Speed Limit

Command epon(slot0-olt1-onu1-fe1)#qos egress-shapping < max-rate>

Grammar <schedule-algorithm>

Set ONU port’s downlink bandwidth limits.

Function Input “qos egress-shapping” to show the current downlink speed
limit configuration information .

< max-rate> Maximum downlink bandwidth ;unit :kbps ;valid value:0-100000;

Port’s output flow shaping ‘s adjusty calculation method with valid

<schedule- value ::
algorithm> weighted-fair
strict-priority

4.3.4.6.7. ONU UNI Port VLAN Configuration

4.3.4.6.7.1.1. Add VLAN

Command epon(slot0-olt1-onu1-fe1)#ctc vlan add cEtherType <ctype>

Grammar cVLANTag <cvlantag> sEtherType <stype> sVLANTag <svlantag>

Function Add appointed ONU UNI port’s VLAN.

www.cdatatec.com 35 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Ethernet type, ranging from 0 to 65536, typically set to 33024

< ctype>
(0x8100)

<cvlantag> valid value range from 0 to 4095

Converted vlan Ethernet type, ranging from 0 to 65536. UNI port is

< stype> set to tag or trunk mode, this parameter should be set to 0 or null.

Conversion vlan tag in the range of 0 to 4095. UNI port is set to tag or
<svlantag>
trunk mode, this parameter should be set to 0 or null.

【Example】

1.Add vlan100 to ONU UNI port 1:

epon(slot0-olt1-onu1-fe1)#ctc vlan add cEtherType 33024 cVLANTag 100
2. Translate vlan100 to vlan200 at ONU UNI port 1:
epon(slot0-olt1-onu1-fe1)#ctc vlan add cEtherType 33024 cVLANTag 100 sEtherType 33024
sVLANTag 200

4.3.4.6.7.1.2. Delete VLAN

Command
epon(slot0-olt1-onu1-fe1)#ctc vlan delete cVLANTag <cvlantag>
Grammar

Function Delete appointed ONU UNI port’s Vlan

< vlanid > Appointed vlan to be deleted with valid value range from 0 to 4094

4.3.4.6.7.1.3. Configure ONU UNI Port’s VLAN Forwarding Mode and PVID

Command epon(slot0-olt1-onu6-fe1)#ctc vlan policy <policy> etherType <type>

Grammar pvid <pvid>

Function Configure ONU UNI port’s VLAN forwarding Mode and PVID

The values are as follows <policy>

policy0 Transparent mode, ignoring etherType and pvid value
< policy> policy1 Access mode
policy2 VLAN translation mode
policy4 VLAN trunk mode.

Ethernet type, ranging from 0 to 65536, typically set to 33024

<type>
(0x8100)

<pvid> valid value range from 0 to 4095

www.cdatatec.com 36 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

【Example】
1.Set ONU1 port 1 transparent mode:
epon(slot0-olt1-onu1-fe1)#ctc vlan policy policy0
2 Set ONU1 port 1 to tag mode, set the port pvid to 100:
epon(slot0-olt1-onu1-fe1)#ctc vlan policy policy1 etherType 33024 pvid 100
3 Set ONU1 port 1 to trunk mode, set the port pvid to 1:
epon(slot0-olt1-onu1-fe1)#ctc vlan policy policy4 etherType 33024 pvid 1

【Illustration】

1. Policy0: transparent mode,.

Direction Frame Type Approach
Ingress Untagged without any changes (to retain the original VLAN TAG),
forwarding
Tagged without any changes, forwarding
Egress Untagged without any changes (to retain the original VLAN TAG),
forwarding
Tagged without any changes, forwarding

2. policy1：Access mode
Direction Frame Type Approach
Ingress Untagged Insert VLAN tag (main parameter is the VID), forwarding.
(TPID = 0x8100, Pri = 0, VID = Port VID))
Tagged ignore the frame
Egress Untagged ignore the frame
Tagged Forward to the appropriate UNI port and strip VLAN TAG
according to VID; if frame tagged VLAN ID is not equal to
Port VID, the frame will be discarded.

3. policy2：Translation mode
Direction Frame Type Approach
Ingress Untagged Insert VLAN Tag, forwarding. (TPID = 0x8100, Pri = 0,VID =
Port VID)
Tagged If VID of frame is included in input VLAN list of the UNI
port the VID will be translated to output VID. Then
forward the frame.
Discard the frame if VID of frame is not included in input
VLAN list of the UNI port
Egress Untagged ignore the frame
Tagged If VID of frame is included in output list of the UNI port
the VID will be translated to input VID. Then forward the

www.cdatatec.com 37 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

frame.
Strip VLAN tag and forward the frame if the VID is equal
to PVID
Discard the frame if VID of frame is not included in the
output VLAN list of the UNI port.

4. policy4：Trunk mode
Direction Frame Type Approach
Ingress Untagged Insert VLAN Tag, forwarding. (TPID = 0x8100, Pri =
0,VID=Port VID)
Tagged Forward the frame if VID of frame is included in “allows
VLAN” list;
Discarded the frame if VID of frame isn’t included in
“allows VLAN” list;
Egress Untagged ignore the frame
Tagged Forward the frame if VID of frame is included in “allows
VLAN” list;
Strip VLAN TAG and forward the frame if the VID is equal
to PVID
Discarded the frame if VID of frame isn’t included in
“allows VLAN” list;

4.3.4.6.7.1.4. Show ONU UNI Port’s VLAN Configuration

Command
epon(slot0-olt1-onu1-fe1)#ctc vlan show
Grammar

Function Show ONU UNI port’s VLAN configuration information

4.3.4.6.8. Reboot ONU

Command
epon(slot0-olt1-onu1)#reboot
Grammar

Function Reboot onu

4.3.4.6.9. Configure RSTP Function

Command epon(slot0-olt1-onu1)#rstp <oper>

www.cdatatec.com 38 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Grammar

Configure ONU’s rapd spanning tress protocol ( RSTP) function;

Function
Input “rstp” to show current RSTP status

Enable/disable ONU RSTP function with valid value as follows:

<oper> Enable: enable ONU RSTP function
Disable: disable ONU RSTP function

4.3.4.6.10. Save ONU configuration

Command
pon(slot0-olt1-onu1)#save
Grammar

Function Save ONU’s all configuration .

4.3.4.6.11. Configure ONU’s Traffic Flow Management

Command
epon(slot0-olt1-onu1)#user-traffic <oper>
Grammar

Configure ONU user’s traffic flow management

Function
When input “user” to show the onu user’s current traffic flow

enable :enable onu user’s traffic flow

<oper>
Disable: disable onu user’s traffic flow

4.3.4.6.12. Configure ONU VLAN’s Ethernet Parameter

Command epon(slot0-olt1-onu1)#vlan-type ethtype <type> upstream <uptag>

Grammar downstream <dntag>

Configure onu vlan’s Ethernet type and set this vlan’s Ethernet traffic
Function direction;
Input “ vlan-type “ to show onu’s current VLAN Ethernet information.

VLAN’s Ethernet type with default value as 0x8100 and the valid value
<type>
range from 0 to 65535

<uptag> Whether add the vlan tag of the vlan Ethernet type for the uplink

www.cdatatec.com 39 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

traffic ;
tag : add tag
Untag: do not add tag

Whether add the vlan tag of the vlan Ethernet type for the downlink
traffic ;
<dntag>
tag : add tag
Untag: do not add tag

4.3.4.7. Configure Link ID Overwrite Function

Command
epon(slot0-olt1)#overwrite-linkid <oper>
Grammar

Whether new authorized link overwrites the existing link ID after the
Function
Link ID is set .

<oper> Enable: new Link overwrites existing Link ID.

Disable: new Link does not overwrite existing Link ID.

4.3.4.8. Configure ONU ID Overwrite Function

Command
epon(slot0-olt1)#overwrite-onuid < oper >
Grammar

Whether new authorized ONU overwrites the existing ONU ID after

Function
the ONU ID is set .

Enable: new ONU overwrites existing ONU ID.

<oper>
Disable: new ONU doesn’t overwrites existing ONU ID .

4.3.4.9. Reboot PON Card

Command
epon(slot0-olt1)#reboot
Grammar

Function Reboot PON card

www.cdatatec.com 40 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.4.10. Save PON card configuration

Command
epon(slot0-olt1)#save
Grammar

Function Save PON card’s all configuration

4.3.4.11. Show OLT’s Basic Information

Command
epon(slot0-olt1)#show
Grammar

Function Show OLT’s basic configuration

【Example】

1.Show OLT’s current basic configuration

epon(slot0-olt1)#show
Olt Basic Configurations:
mac address :00:0d:b6:37:23:00
work state :Online
enable status :Enable
max permitted link number :210
registered link number :1
accessed onu number :1
link id exhausted :NO
onu id exhausted :NO
link id overwrite :NO
onu id overwrite :NO

4.3.5. Configure Enable Password Management

Command
epon#passwd
Grammar

Function Enter the enable password changing mode .

www.cdatatec.com 41 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

【Example】

1.Change enable password :

epon#passwd
Enter new enable password:
Confirm new enable password:
epon#

【Remark】

Please do save the configuration under the system directory after changing the password and
reboot the system to make the setting valid .

4.3.6.RSTP Configuration Mode

Command
epon#rstp
Grammar

Function Enter switch control module’s RSTP management mode 进

【Example】

1.Enerer RSTP Management Mode

epon#rstp
epon(rstp)#

epon(rstp)# ? input“？” or “help” to show current directory

bridge - bridge
disable - disable rstp
enable - enable rstp
hold-count - set rstp transmit hold count
port - rstp port parameter configuration
show - show rstp configuration

4.3.6.1. Configure RSTP Bridge Parameter

4.3.6.1.1. Bridge Forward Delay

Command epon(rstp)#bridge fdelay < fdelay >

www.cdatatec.com 42 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Grammar

Function Set RST Bridge delayed forward

Value range : 4-30 ;must demand the following bind relation:

2×（ForwardDelay – 1.0second） >= MaxAge
< fdelay >
MaxAge is bridge infomration’s maximum valid time ;
ForwardDelay: forward delay

4.3.6.1.2. Bridge Maximum Valid Age

Command
epon(rstp)#bridge maxage < maxage>
Grammar

Configure RSTP bridge’s maximum valid age which is the valid time for
Function
receiving BPDU packet from appointed port’s bridge.

Value range : 6-40 ;must demand the following bind relation:

2×（ForwardDelay – 1.0second） >= MaxAge
< maxage>
MaxAge is bridge infomration’s maximum valid time ;
ForwardDelay: forward delay

4.3.6.1.3. Bridge Priority

Command
epon(rstp)#bridge priority <priority>
Grammar

Function Set RSTP bridge priority

Appointed bridge priority integer value from 1 to 61440,and step

<priority>
length is 4096 ,meaning 4096xN( N is from 0 to 15) .

4.3.6.2. Enable RSTP Function

Command
epon(rstp)#enable
Grammar

Function Enable switch control module’s uplink port ‘s RSTP function

【Example】

1.Enable switch control module’s uplink port ‘s RSTP function

epon(rstp)#enable

www.cdatatec.com 43 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.6.3. Disable RSTP Function

Command
epon(rstp)#disable
Grammar

Function disable switch control module’s uplink port ‘s RSTP function

4.3.6.4. Hold Bridge Forwarding Frame Count

Command
epon(rstp)#hold-count <holdcount>
Grammar

Configure RSTP’s deliving BPDU packet limit and appoint the

Function
maximum delivering BPDU packet within 1 second .

<holdcount> Value range from 1 to 10.

4.3.6.5. Configure RSTP Port Parameter

4.3.6.5.1. Set RSTP’s Edge port Management

Command
epon(rstp)#port <portlist> edgecfg <edge>
Grammar

Configure RSTP port’s managed edge port attribute. Appoint the port
whether to be edge port or not .Edge port does not go through
Function
“discarding-learning-forwarding “ step but transfer to switch status
directly .

<portlist> Appointed port list ,any one from ge1 to ge4 .

Configure appointed RSTP port’s edge port attribute with byte value
<edge>
such as edge ,non-edge and auto .

4.3.6.5.2. Set RSTP Port’s Protocol Version Checkout

Command
epon(rstp)#port <portlist> mcheck
Grammar

www.cdatatec.com 44 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Configure RSTP port’s protocol version check out .When executing

this command ,the appointed port’s mode is force to be the same as
next received BPDU packet version.If the next packet is STP BPDU
Function
packet ,the port’s mode is STP .If it’s RSTP BPDU packet ,the port’s
mode is RSTP. RSTP port’s protocol version is a booting command, not
available to preserve the attributed value continually .

<portlist> Appointed port list ,any one from ge1 to ge4 .

4.3.6.5.3. Set RSTP Port’s Point-to-Point Attribution

Command
epon(rstp)#port <portlist> p2pcfg <p2p>
Grammar

Configure RSTP port’s point to point index . whether the appointed

port is point-to-point port.Point to point port could allow to switch
Function to forward status rapidly .Non-point to point port needs to go
through step of discarding-learning-forwarding first before switching
to forward status .

<portlist> Port list from ge1 to ge4

Appointed RSTP port index with bytes value such as p2p,shared and
<p2p>
auto .

4.3.6.5.4. Set RSTP Port’s Link Cost

Command
epon(rstp)#port <portlist> path-cost <pathcost>
Grammar

Configure RSTP port’s link cost .It’s used to calculate the root link’s
Function cost .The port with the lowest root link cost will change to forward
port when delivering the same bridge ID .

<portlist> Appointed port list, any one from ge1 to ge4.

Appointed RSTP port’s link cost with integer value from 1 to

<pathcost>
200000000.

4.3.6.5.5. Set RSTP Port’s Priority Level

Command
epon(rstp)#rstp port <portlist> priority <priority>
Grammar

www.cdatatec.com 45 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Configure RSTP port’s priority level. The port with priority will change
Function to forward port when delivering the same bridge ID and having the
same link cost .

<portlist> Port list ,any one from ge1 to ge4.

Configure appointed RSTP port’s priority level with integer value valid
<priority>
from 1 to 240 ,step length 16 ,meaning 16xN(n is from 0 to 15 ) .

4.3.6.6. Show RSTP Configuration Information

Command
epon(rstp)#show
Grammar

Function Show RSTP bridge and port’s configuration information

【Example】

1.show switch control module’s RSTP configuration information :

epon(rstp)#show
RSTP Bridge Status:
RSTP Setting :Disable
Bridge ID [PRI-MAC] :32768-e0:67:b3:00:63:07
Bridge Hello Time :2 sec
Bridge Max Age :20 sec
Bridge Forward Delay :15 sec
Transmit Hold Count :6
Root Bridge ID :0-00:00:00:00:00:00
Root Path Cost :0
RSTP Port Status:
PID Mode Pri PathCost EdgeCfg OperEdge P2PCfg OperP2P State
1 RSTP 128 20000 Auto Non-Edge Auto P2P LinkDown
2 RSTP 128 20000 Auto Non-Edge Auto P2P LinkDown
3 RSTP 128 20000 Auto Non-Edge Auto P2P LinkDown
4 RSTP 128 20000 Auto Non-Edge Auto P2P LinkDown

www.cdatatec.com 46 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.7. Configure switch control module’s Switching Mode

4.3.7.1. Set Private Vlan Mode

Command
epon#swmode pve <mode> <net-port>
Grammar

Function Configure private vlan mode for uplink port of switch control module

Private vlan mode :

<disable | onebyone | trunk>。

disable:normal switch mode ,where the uplink port of switch control
< mode >
module doesn’t has VLAN limitation .
Onebyone: switch control module’s uplink port is corresponding with
PON port -----corresponding mode ,such as ge1-ge5,ge3-ge6Trunk:
port convergence mode

When mode is trunk mode ,that means to converge the uplink

< net-port >
ports .port from ge1 to ge4 .

4.3.7.2. Show switch control module’s Switch Mode Configuration

Command
epon#swmode show
Grammar

Function Show switch control module’s switch mode

【Example】

1. Show switch control module’s switch mode configuration information

epon#swmode show
Current basic switch mode :vlan-unaware
Current private vlan mode :disabled

4.3.7.3. Enable switch control module’s Vlan Function

Command
epon#swmode vlan <mode>
Grammar

www.cdatatec.com 47 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Function Enable switch control module’s Vlan Function

aware: eable vlan（vlan aware）

<mode>
unaware: disable vlan (vlan unaware)

4.3.8. Uplink Port Management mode of switch control

module

Command
epon#swport <port>
Grammar

Enter port management mode of switch control module .under this

Function
mode , you can configure several index function.

<port> Appointed port list ,any one from ge1 to ge6.

【example】

1.Enter switch control module’s port 1 management mode

epon#swport ge1
epon(ge1)#

epon(ge1)# ? input“？”or “help”to show directory :

acc-frame - set port access frame type
def-pri - set port default priority
duplex - set port duplex
[no] enable - set port enable
flow-ctrl - set port flow control
ingr-filter - set port ingress filter
mode - set port mode
nest-vlan - set port nest vlan enable or disable
prot-vlan - set port protocol based vlan enable or disable
pvid - set port pvid
rate-ctrl - set port ingress rate limit parameters
reautonego - set port reautonegotiation
show - show port attribute information
[no] shutdown - shut down a port
speed - set port speed

www.cdatatec.com 48 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.8.1. Set Port’s RX Frames Types

Command
epon(ge1)#acc-frame <type>
Grammar

Function Set switch control module port’s RX packet frame types

Packet frame types :

tagged:receive tagged packet only
<type>
untagged: receive untagged packet only
all:receive all types of packet frame

【Remark】

Our OTL system can’t set untagged type mode yet .

4.3.8.2. Set Port’s Default Priority Level

Command
epon(ge1)#def-pri < privalue >
Grammar

Set switch control module’s default priority level ,similar to

PVID .When port received untagged vlan packet ,the packet is set by
Function priority .The priority level is port’s default 802.1P priority .The data
packet will enter different priority queue to receive different service
according to corresponding priority level and flow category .

< privalue> Set configured port’s priority level value from 0 to 7

4.3.8.3. Configure Port’s Duplex Mode

Command
epon(ge1)#duplex < duplex >
Grammar

Function Set switch control module port’s duplex mode

full:full duplex mode

< duplex> half:half duplex mode
auto:auto-negotiation mode

www.cdatatec.com 49 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.8.4. Enable Port

Command
epon(ge1)#enable
Grammar

Enable the switch control module port to deliver and receive packet.
Function Under some circumstance, user can use this function to test the
networking performance.

4.3.8.5. Disable Port

Command
epon(ge1)#no enable
Grammar

Disable the switch control module port to deliver and receive packet.
Function Under some circumstance, user can use this function to test the
networking performance.

4.3.8.6. Configure Port’s Flow Control Mode

Command
epon(ge1)#flow-ctrl <ctrl>
Grammar

Configure switch control module port’s flow control mode. Both

optical port mode and electrical mode could support flow control
configuration enforcedly and auto-negotiation;
Function Under the half-duplex mode ,the port enable the back flow control
function default;
Under the full-duplex mode, you can enable or disable flow control in
compliant with 802.x standard.

enable: enable flow control function

<ctrl> disable:disable flow control function
auto:auto-negotiation mode

4.3.8.7. Set Port’s RX Filter Function

Command
epon(ge1)#ingr-filter <operator>
Grammar

Function Configure switch control module port’s RX packet filtering function.

www.cdatatec.com 50 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

When the port is not the vlan member appointed by frame VID ,the
packet is dumped at the time of receiving the frame .

Enable: enable switch control module port’s RX frame filter function

<operator>
Disable: disable switch control module port’s RX frame filter function

4.3.8.8. Configure Port Mode

Command
epon(ge1)#mode <mode>
Grammar

Configure switch control module port’s port mode,including copper

Function
and fiber modes .

Copper: copper mode

<mode>
fiber :fiber mode

4.3.8.9. Enable Port’s Nest-Vlan Function

Command
epon(ge1)#nest-vlan <operator>
Grammar

Function Configure switch control module port’s nest vlan function

enable :enable port nest’s vlan function

<operator>
Disable: disable port nest’s vlan function

4.3.8.10. Enable Port’s Protocol Vlan

Command
epon(ge1)#prot-vlan <operator>
Grammar

Function Configure switch control module port’s protocol vlan function

Enable: enable port’s protocol vlan function

<operator>
Disable: disable port’s protocol vlan function

【Remark】

This command’s effect is the same as “[no] enable <portlist>” underthe protocol vlan
configuration mode .
4.3.5.6.Enable Port Protocol VLAN Function
4.3.5.7.Disable Port Protocol Vlan Function

www.cdatatec.com 51 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.8.11. Set Port’s PVID

Command
epon(ge1)#pvid <pvid>
Grammar

Function Configure switch control module port’s default vlan ID .

<pvid> Vale range from 0 to 4094

4.3.8.12. Configure Port’s Rate Limits

4.3.8.13. Configure Port’s Reauto-Negotiation Function

Command
epon(ge1)#reautoneg
Grammar

Configure switch control module port’s auto-negotiation function,

which is needed on the purpose of networking debugging. This
function could be replaced by means of plug in and out of the
Function cable ,but if the cable/fiber is too complicated or too far ,it is better
to realize it via software .Therefore ,port configuration management
module must provide a command port for reauto-negotiation
command ,which doesn’t preserve the attributed value continually.

4.3.8.14. Show Port Information

Command
epon(ge1)#show
Grammar

Function Show switch control module port’s configuration information

【Example】

1.Show switch control module port 1 ‘s configuration information

epon(ge1)#show
------------------ PortId 2 Attribution --------------------
Auto-Negotiation:enable AdminStatus :enable
PVID :1 DefaultPriority :0
Learning :enable AccFrameType :All
CfgSpeed :1000M CfgDuplex :full
WorkSpeed :10M WorkDuplex :half

www.cdatatec.com 52 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

CfgFlwCtrl :disable LinkStatus :down

IngressRateCtrlType:All IngressRateLimit:0
EgressRateLimit :0
------------------------------ End ------------------------------

4.3.8.15. Configure Port’s Compulsive Shutdown Function

Command
epon(ge1)#shutdown
Grammar

Configure switch control module port’s compulsive shutdown

function. In an exceptional case, such as attached by virus or hacker
Function
and can’t take any actions ASAP , the shutdown port function is
recommended .

4.3.8.16. Remove Compulsive Shutdown Port

Command
epon(ge1)#no shutdown
Grammar

Remove switch control module port’s compulsive shutdown function.

Function In an exceptional case, such as attached by virus or hacker and can’t
take any actions ASAP , the shutdown port function is recommended .

4.3.8.17. Configure Current Port Rate

Command
epon(ge1)#speed <speed>
Grammar

Configure switch control module port’s speed.Under fiber port

mode ,the port could only work at the speed of 1000Mbps;Under the
Function
copper port mode ,the port can work at different speed and available
for auto-negotiation function configuration .

10m: 10mbps
100m: 100mbps
<speed> 1g: 1gbmp(1000mbps)
10g: 10gbps
Auto: auto-negotiation

www.cdatatec.com 53 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.9.System Configuration Mode

Command
epon#system
Grammar

Function Enter EPON system’s management mode

【Example】

1.Enter system management mode

epon#system
epon(sys)#

epon(sys)# ? input “？”or “help” to show current directory

cfg-sync - synchronize onu config with its config file
console - configure console parameters
onu-auth - configure ONU authentication parameters
read-comm - set snmp read community string
reboot - reboot the system
restore - restore to saved configuration
save - save system configuration
trap-addr - set trap destination IP address
write-comm - set snmp write community string

4.3.10. Synchrony with ONU Configuration

Command
epon(sys)#cfg-sync <slot> <status>
Grammar

Configure OLT’s setting is synchronous with ONU configuration. When

this function is enabled , ONU will remove its own nvs automatically
Function before ONU authorized to OLT .All configuration under the ONU will
be cleared .All ONU’s configuration is valid after authorized under the
OLT .

<slot> PON card slot with integer value from 1 to 4 .

<timeout> Optional index:<enable|disable>。

【Remark】

This function default is close because enabling it will make ONU’s saved configuration

www.cdatatec.com 54 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

lost ,needing to configure it again undet the OLT .Please use this function properly .

4.3.10.1. Backup EPON System Configuration

Command
epon(sys)#config backup<host>
Grammar

Function Put all EPON sytems’s configuration file backup to TFTP server.

<host> Appointed TFTP server’s IP address

4.3.10.2. Restore EPON System Configuration

Command
epon(sys)#config upgrade <host>
Grammar

Download system’s configuration file from TFTP server and restore

Function
EPON system’s configuration.

<host> Appointed TFTP server’s IP address

4.3.10.3. Configure Console Port Speed

Command
e pon(sys)#console speed<speed>
Grammar

Function Set OLT system’s console port speed

Value range:bps2400-bps115200。
<speed>
Remark: value should be 2400*2^n (n is integer)

4.3.10.4. ONU Authorization Management Mode

Command
epon(sys)#onu-auth
Grammar

Function Enter onu authorization management mode

【Example】

www.cdatatec.com 55 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

1.enter onu authorization management mode

epon(sys)#onu-auth
epon(sys-onuauth)#

epon(sys-onuauth)# ? input“？”or“help”to show directory:

inv-onu - process invalid ONU list
list - configure ONU address range
type - set authentication type

4.3.10.4.1. Illegal ONU List Operation

4.3.10.4.1.1. Clear Illegal ONU List

Command
epon(sys-onuauth)#inv-onu clear
Grammar

Clear current illegal ONU list ,then the illegal onu can get a new
Function
chance to be authorized under OLT .

4.3.10.4.1.2. Show Illegal ONU List

Command
epon(sys-onuauth)#inv-onu show
Grammar

Function Show illegal ONU list and list all illegal ONU’s MAC address

4.3.10.4.2. Configure ONU Authorized Address List

4.3.10.4.2.1. Add ONU Authorized Address List

Command
epon(sys-onuauth)#list add <start> <end> <type>
Grammar

Function Add an ONU address list and appoint its authorization type

<start> ONU starting MAC address: such as 00:A1:02:02:01:B0

<end> ONU ending MAC address: such as:00:A1:02:02:01:F0

Set onu authorization type under address list with following value:
Blacklist: the ONU with this type of MAC address can’t be authorized
<type> to OLT .
Whitelist: the onu beyond this MAC address range can’t be
authorized .

www.cdatatec.com 56 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

【Example】

1.Add the ONU with the MAC address : 00:A1:02:01:12:B0 to the blacklist

epon(sys-onuauth)#list add 00:A1:02:01:12:B0 blacklist

4.3.10.4.2.2. Delete ONU Authorized Address List

Command
epon(sys-onuauth)#list delete <index>
Grammar

Function Delete an ONU address list

<index> MAC address list index

4.3.10.4.2.3. Show Current MAC Address List

Command
epon(sys-onuauth)#list show
Grammar

Show current ONU authorized address list and distribute an index

Function
directory for all the MAC address automatically

【Example】

1.Show current ONU authorized MAC address list:

epon(sys-onuauth)#list show
NO. Start Address End Address Type
1 00:a1:02:01:12:b0 00:a1:02:01:12:b0 blacklist

4.3.10.4.3. Configure ONU Authorized Type

Command
epon(sys-onuauth)#type <type>
Grammar

Function Set EPON system ONU’s authorized type

Valid value:<blacklist | whitelist | none>。

Blacklist: All onu in the MAC address type can’t be authorized .
<type>
Whitelist: All ONU beyond the MAC address type can’t be authorized.
None: non-authorization ,all ONU could be authorized .

www.cdatatec.com 57 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.10.5. Set SNMP Read Community

Command
epon(sys)#read-comm <community>
Grammar

Function Set EMS software SNMP’s read community

Read community with bytes serial ,the longest length couln’t be over
< community >
26 bytes ,such as public .

4.3.10.6. Reboot OLT

Command
epon(sys)#reboot <device> <slot> <olt> <onu>
Grammar

Reboot EPON device;This command will reboot switch control

module , some PON card ,some ONU or the equipment under the
Function EPON system .
Input command “ reboot “ will only reboot the switch control module
.

Appoint the device to be rebooted with following index:

ctrl-card: reboot switch control module
<slot><olt> <onu> is ignored .
pon-card :reboot appointed pon card with index <slot)
<device>
<olt> <onu> is ignored .
Onu:reboot appointed onu under the index <slot> <olt> <onu>
all : reboot the whole EPON system including OLT and ONU .
<slot><olt> <onu> is ignored.

<slot> Appoint PON card’s slot number with valid value from 1 to 4 .

Appoint PON port number under a pon card slot with valid value
<olt>
from 1 to 2 .

<onu> Appoint ONU number with valid value from 1 to 64 .

【Example】

1.Reboot switch control module

epon(sys)#reboot
Or

3.Reboot the whole EPON system including switch control module ,all online PON card and all

www.cdatatec.com 58 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

online ONU)

epon(sys)#reboot all

4.3.10.7. Restore Default Configuration and Reboot Equipment

Command
epon(sys)#restore <device> <slot> <olt> <onu>
Grammar

Restore ex-factory default configuration and reboot the device .

Function When <device> <slot> <olt> <onu> is ignord ,the command just
restore switch control module configuration .

Appoint the device to restore default configuration with valid index :

ctrl-card: restore switch control module’s default configuration
<slot><olt> <onu> is ignored
pon-card: restore appointed PON card under <slot> configuration
<device> <olt> <onu> is ignored.
onu :restore default configuration for appointed onu with index :
<slot> <olt> <onu>
all: restore system’s all default configuration and command
<slot><olt> <onu> is ignored .

<slot> Appoint PON card’s slot number with valid value from 1 to 4 .

<olt> Appoint PON port number with valid value from 1 to 2 .

<onu> Appoint ONU number with valid value from 1 to 64 .

4.3.10.8. Save Current Configuration

Command
epon(sys)#save <device> <slot> <olt> <onu>
Grammar

Save current configuration.

Function Just input “ save “ command to save the switch control module’s
current configuration .

<device> Appoint the device to save current configuration with valid index :
ctrl-card: save switch control module’s current configuration
<slot><olt> <onu> is ignored
pon-card: save appointed PON card under <slot> configuration
<olt> <onu> is ignored.

www.cdatatec.com 59 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

onu :save configuration for appointed onu with index : <slot>

<olt> <onu>
all: save system’s all default configuration and command <slot><olt>
<onu> is ignored .

<slot> Appoint PON card slot number with valid value from 1 to 4 .

<olt> Appoint PON port number with valid value from 1 to 2 .

<onu> Appoint ONU number with valid value from 1 to 64 .

4.3.10.9. Set Trap Receiving IP Address

Command
epon(sys)#trap-addr <index> <ip-addr>
Grammar

Function Configure EPON’s receiving trap IP address with 4 IP at most.

<index> Trap receiving IP index with valid value from 1 to 4 .

<ip-addr> Set trap receiving IP address ,such as 192.168.0.1.

4.3.10.10. Set SNMP Written Community

Command
epon(sys)#write-comm <community>
Grammar

Function Set SNMP’s written community of EMS software

Written community with bytes serial ,longest length 26 bytes ,such

< community >
as : private .

4.3.11. Trunk Management Mode

Command
epon#trunk <trunkid>
Grammar

Create a trunk group and enter the trunk management mode for
Function
configuration .

< trunkid > Trunk number with valid value from 1 to 4

www.cdatatec.com 60 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

【Example】

1.Create trunk 1 and enter trunk 1’s management mode

epon#trunk 1
epon(trunk1)#

epon(trunk1)# ? input “？”or“help”to show current directory

balance-algorithm - set trunk balance algorithm
delete - delete the specifically trunk
member - Set trunk member

4.3.11.1. Configure Trunk Balance Algorithm

Command
epon(trunk1)#balance-algorithm < balance>
Grammar

Configure trunk’s balance algorithm.All balance algorithm is the same

when all trunk group adopts the same balance algorithm.
Trunk group’s packet can be shared among trunk member
Function
poprts .EPON system support several balance algorithm ,such as
based on MAC address ,IP address ,transmission port number,
MAC+IP, MAC+ transmission port number

Trunk algorithm with valid index :

mac :based on MAC address’s KE balance algorithm.
Ip: based on IP address’s balance algorithm
<balance > l4port: based on transmission port’s balance algorithm
ip-mac: based on MAC+IP address’s balance algorithm
l4port-mac
inl2if :based on packet receiving port’s balance algorithm

4.3.11.2. Delete Trunk Group

Command
epon(trunk1)#delete
Grammar

Function Delete trunk group and its member

www.cdatatec.com 61 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.3.11.3. Add Trunk Member

Command
epon(trunk1)#member <portlist>
Grammar

Function Add trunk group’s member pot

<portlist> Appoint trunk member port list from ge1 to ge8

【Example】

1.Add member port ge1,ge3,ge4 and ge8 to trunk 1 .

epon(trunk1)#member ge1,ge3-ge4,ge8

4.3.12. Show Trunk Configuration Information

Command
epon#show trunk
Grammar

Function Show switch control module’s current trunk configuration

4.3.13. User Management

4.3.13.1. Set User Authority

Command
epon#user access <name> < access >
Grammar

Change appointed user’s priority mode to limit use to access to

Function
system or limit the user right .

Appointed user name under the priority mode with the length from 4
<name>
to 15 bytes.

admin : manager who has all the configuration and operation rights .
<access>
Guest: guest who could only ready the operation. Configuration

【Remark】

www.cdatatec.com 62 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Only the system administer has the rights to change the system user’s priority.

4.3.13.2. Add User

Command
epon#user add <name> <passwd> < access >
Grammar

Function Add a user

<name> User name with the length from 4 to 15 bytes.

Optional index to change new password .if there is no index ,the

<passwd> user’s password is blank ;if index is provided ,it could be any obvious
bytes combination with the length from 6 to 31 bytes .

admin : administer who has all the configuration and operation

<access> rights .
Guest: guest who could only ready the operation. Configuration

4.3.13.3. Delete User

Command
epon#user delete <name>
Grammar

Function Delete appointed user from logging in the system

Appoint the user name to be deleted with the bytes length from 4 to
<name>
15

【Remark】

Only the system’s administer( the user priority level is 1) has the rights to add and delete
system users .

4.3.13.4. Change User Password

Command
epon#user passwd <name> [<password>]
Grammar

Change appointed user’s log in password .

Function
If <password> is ignored , the log in password is blank.

<name> User name with the bytes length from 4 to 15 bytes .

<password> Optional index to input new password .

www.cdatatec.com 63 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

If the index is not provided ,the password is blank ;if the index is
provided ,the password length can be from 6 to 31 bytes.

4.3.13.5. Show Current User’s Information

Command
epon#user show
Grammar

Function Show system’s all user list

【Example】

1.Show System’s Current User List

epon#user show
User: admin Access: administrator|0 Timeout: 1800
User: guest Access: guest|0 Timeout: 600

4.3.13.6. Change User’s Timeout

Command
epon#user timeout <name> <timeout>
Grammar

Change appointed user’s timeout time. Within the timeout time ,user
Function
can’t make any operation and log out the system automatically.

<name> Change timeout user name with the byte length from 4 to 15 bytes.

Appointed user’s timeout time with the valid index range from 1to
<timeout>
3600 and unit is second.

【Remark】

Change user’s timeout function ,which is valid after logging in the system again .

4.3.14. VLAN Management Mode

Command
epon#vlan <vlanid>
Grammar

Function Create a vlan and enter vlan management mode for configuration .

www.cdatatec.com 64 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

< vlanid > Vlan ID to be modified or created with valid value from 1 to 4094.

【Example】

1.Create Vlan100 and enter vlan100’s management mode

epon#vlan 100
epon(vlan100)#

epon(vlan100)# ? input“？”or “help” to show current directory:

delete - delete vlan members or vlan
member - add vlan member

4.3.14.1. Delete Vlan Member

Command
epon(vlan100)#delete member <portlist>
Grammar

Delete vlan member port.

Function
Input “delete member” to to delete this vlan and member port.

<portlistt> Appoint vlan member port list ,any port from ge1 to ge16.

4.3.14.2. Delete Vlan

Command
epon(vlan100)#delete
Grammar

Function Delete current vlan and all member ports under this vlan.

4.3.14.3. Add Vlan Member Port list

Command
epon(vlan100)#member <portlist> <tag>
Grammar

Function Add vlan member port and set its tag mode.

<portlistt> Added vlan member port list ,from ge1 to ge16.

Tag mode with fixed index “tag” .

When the member port is marked with tag .The packet from the port
<tag>
is added with vlan tag .
When tag is deleted ,this port is not marked with tag .

www.cdatatec.com 65 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

【Example】

1.add switch control module port ge1,ge2,ge3 with vlan 100 to the tag member ports ,while port
ge4,ge5,ge16 are member ports with vlan100 without tag .

epon(vlan100)#member ge1-ge3 tag

epon(vlan100)#member ge4-ge5,ge16

4.3.15. Show Vlan Configuration Information

Command
epon#show vlan
Grammar

Function Show switch control module’s vlan configuration information .

【Example】

1.Show switch control module’s valn configuration:

epon#show vlan
vlan 1:
tagged ports :
untagged ports :ge1-ge16
vlan 100:
tagged ports :ge1-ge3
untagged ports :ge4-ge5,ge16

www.cdatatec.com 66 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.4. Show System Running Information

4.4.1. Show System’s Current CPU Running Status

Command
epon>show cpu
Grammar

Function Show system’s CPU running status information

【Example】

1.Show system’s CPU Running Information:

epon>show cpu
NAME ENTRY TID PRI total % (ticks) delta % (ticks)
------------ ------------ ---------- --- --------------- ---------------
tJobTask 0xd19a4 0x8ac158 0 0% ( 0) 0% ( 0)
mTrAging 0x43975c 0xf7c350 5 0% ( 0) 0% ( 0)
tErfTask 0xb46bc 0x8b5a30 10 0% ( 0) 0% ( 0)
intSched0 0x31a72c 0xf0b5e0 10 0% ( 0) 0% ( 0)
intSched1 0x31a72c 0xf16880 10 0% ( 0) 0% ( 0)
tNetTask 0x363c0 0x945d00 40 0% ( 0) 0% ( 0)
tIbcpPoll 0x13dc7c 0x1243cd0 45 0% ( 0) 0% ( 0)
tIbcpRx 0x13e74c 0x1241338 46 13% ( 2) 13% ( 2)
tXbdService 0xccba0 0xa1af80 50 0% ( 0) 0% ( 0)
tFtp6d 0x2f97c 0xa16ef0 56 0% ( 0) 0% ( 0)
tUserLog 0x16a9c0 0xf826a8 60 0% ( 0) 0% ( 0)
tUpgradeTask 0x167174 0x1348aa8 64 0% ( 0) 0% ( 0)
KERNEL 0% ( 0) 0% ( 0)
INTERRUPT 0% ( 0) 0% ( 0)
IDLE 86% ( 13) 86% ( 13)
TOTAL 99% ( 15) 99% ( 15)

4.4.2.Show System’s Memory Use Status

Command
epon>show mem
Grammar

www.cdatatec.com 67 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Function Show system’s memory use status information

【Example】

1.Show system’s current memory user information:

epon>show mem
status bytes blocks avg block max block
-------- -------------- ---------- ---------- ----------
current
free 12695080 4 3173770 12681624
alloc 12055336 1185 10173 -
internal 408 2 204 -
cumulative
alloc 12702512 1795 7076 -
peak
alloc 12059424 - - -

4.4.3. Show System’s Task Status

Command
epon>show task
Grammar

Function Show system’s current task information

4.4.4.Enable CATV (RF) Function

Current ,C-Data has developed and produced a wide range of ONU models ,such as only data
ONU FD101H,FD111H,FD112H,FD104H,FD104B,FD108B ,and ONU of various service function,
such as FD304H(4FE+RF),FD204H(4FE+2POTS_,FD404H(4FE+2POTS+RF).So far ,our EMS and CLI
NMS could both support data and RF-cutoff function in our EMS or in our CLI management
interface. As for VOIP function, we could only support CLI management on the console port of
the ONU .

Command
epon(slot3-olt2-onu9)#catv enable
Grammar

Function Enable ONU’s RF function

www.cdatatec.com 68 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.4.5. disable CATV (RF) Cut-Off Function

Command
epon(slot3-olt2-onu9)#catv disable
Grammar

Disable ONU’s RF function if subscriber don’t pay CATV cost on time

Function
from the OLT management interface .

4.5. Global Command

Global command can be used under any command mode.

4.5.1.Create Command Alias

Command
alias <alias> <cmd>
Grammar

Function Create appointed command’s alias

<alias> Input command’s alias

<cmd> Original command

4.5.2.Change Directory

Command
cd <directory>
Grammar

Function Enter appointed directory

<directory> Input directory

4.5.3.Clear Screen

Command
clear
Grammar

www.cdatatec.com 69 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

Function Clear screen

4.5.4.Copy File

Command
copy <scr-file> <dest-file>
Grammar

Copy file ;
Function When <dest-file> is ignored , <scr-file> ‘s contents is printed on the
screen.

< scr-file > Source file

<dest-file> destined file

4.5.5.Show System’s Date

Command
date
Grammar

Function Show system’s current date and time .

4.5.6.Delete File

Command
del <filename>
Grammar

Function Delete appointed file

< filename > Appoint deleted file name

4.5.7.Exit From The Current Command Mode

Command
exit
Grammar

Exit from the current command mode and return to the previous
Function
command mode .

www.cdatatec.com 70 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.5.8.Return to System Main Directory

Command
end
Grammar

Function Return to the system’s main directory

4.5.9.Help

Command
help
Grammar

Function Command help

4.5.10. Command History

Command
history
Grammar

Function Show current input command history

4.5.11. Log Out System

Command
logout
Grammar

Function Log out system。

4.5.12. Show Current File List

Command
ls
Grammar

Function Show current directory’s file list

www.cdatatec.com 71 [email protected]
Shenzhen C-Data Technology Co.,Ltd. OLT CLI User Manual

4.5.13. PING

Command
ping <host>
Grammar

Function Test remote host’s connection

< host> Remote host’s ip address

4.5.14. Show Directory Route

Command
pwd
Grammar

Function Show directory route

4.5.15. TFTP

Command
tftp <cmd> <filename> < mode>
Grammar

Function Upload/download file through TFTP

TFTP command:
< cmd> get : download file
Put: upload file

<filename> File name

File format :
<mode> ascii file format
binary format

www.cdatatec.com 72 [email protected]