RFP No. ?????

Bill of Quantity

Construction of Mardin 12 Classrooms School in Ranya, Sulaymania Governorate

# Item Description Unit Quantity

1 Civil Works:
A

Earth works: according to section 300 of I.G.T.S. and instructions of site engineer.
A1 SITE PREPARATION AND DEMARCATION: according to Section 200 of I.G.T.S. and instructions
of the site engineer. Removal of debris, grading, levelling to the appropriate level (+25 cm to -
25 cm), clearance and layout and demolition of all existing materials such as (concrete,
foundations, asphalt, and even rock layers) and transporting resulting materials (Debris) to an
appropriate location outside municipalities border and approved by the site engineer, also
removing and transport and reinstall and establish water network pipes and electrical
networks and poles considering extra materials if needed, the price includes opening access
road according to the work requirements and fixing proper centre lines in two directions and
benchmarks according to the specifications, attached drawing, and instructions of the site
engineer. The works should be done according to section (200) of I.G.T.S, and any depth of
cutting or Removal of Debris required for all the areas must be done according to drawings
and instructions of the site engineer. The price includes providing and fixing 2 signboards for
the site. The signboard should remain on-site till the end of the works and approval of the
project hand, then be removed in addition to fixing and setting out of B.M. control points. The
levelling of the site is according to the assigned design elevation; you should not note the
15cm depth; it will be at a different depth.

NOTE: The contractor should Supply all materials and construct a well-equipped (furniture
and all requirements(laptop, camera, scanner, colour printer) site office of dimension (4 X 5)m
with a(W.C.) for the site engineer before starting the works.
M2 6,500
A2 Excavation and cutting works: Excavation in all types of soils (even rock layers or existing
foundation concretes & Asphalt layer, if any), including back-filling and compaction according
to section (300) requirements of I.G.T.S. The price includes Cutting, levelling and compacting
the site area for any soil type and rocky area according to the details and instructions of the
site engineer. ( The price includes compacting the bottom of the ditches up to 95% MDD and
removing waste and loose material )

M3 1,000
A3 Backfilling works: Supplying materials and filling with approved screened sub-base materials
type B maximum size is 2" where required within the area inside or outside of the fence such
as aprons, walkways, garden, etc. with compaction (according to the specification) in layers 25
cm thickness, the compaction for garage and play yard must be not less than 95% MDD, and
using anti termite chemical (chordin) to prevent and treat the white termite according to the
instructions of the manufacturer and site engineer with all necessary works for the final two
layers.

NOTE: The contractor is obliged to do the compaction test to compare with the required
percentage.

M3 3,500

1
 # Item Description Unit Quantity
B CONCRETE WORKS: Including supply of materials (steel reinforcement, connection steel wires, cement,
aggregate, water, sand, plastic cover for fixing the steel reinforcement in the proper level, bolts, nuts,
washers, G. I. pipes, cutter machines, binder machine, etc.), and all necessary works, according to the
section (600) of I.G.T.S, drawings, and instructions of the site engineer.
Note:
1- Use new plywood for all wooden form support, with Adjustable Steel Scaffolding Props and Formwork
Jack Support.
2- Fy = 276 Mpa for 10mm,12mm steel bars. FY=414Mpa for 16mm,20mm,25mm steel bars
3. Allowable bearing capacity of soil = 100 KN / m2 (assumed).
5. the reinforcement details should be according to the ACI detailing manual 2004.
6. New Plywood or standard formworks must be used for all structural parts.

B1 Lean Concrete: Supply materials and cast plain concrete class (C10) 1:3:6 10cm (min.
thickness) for under-column footing, walkways and raft foundation to the required elevations.
The price includes laying two layers of thick nylon before casting the concrete.
M2 2,000
B2 Raft foundation Concrete: Provide all materials and cast reinforced concrete (ready mix C30)
for a raft foundation with a double layer of reinforcement 12mm dia steel bar @20cmc/c for
both directions, ensuring the concrete thickness of 30cm according to the drawings, fair face
surfaces using copter machine and vibrator during casting and all the required works should
be conducted as per the standard specifications and instructions of supervisor engineer.
M3 570
B3 Column Concrete: Supplying materials and casting reinforced concrete for the columns and
under-tie beam-columns ( pedestals ),(according to the details for different sections ) using
concrete compressive strength C30 for 28 days according to specifications and instructions of
the site engineer.

M3 8
B4 Supplying materials and casting reinforced concrete according to the details for different
sections, according to specifications and instructions of the site engineer, must use a
helicopter and grinding. Note: All the
roofs must be treated and smoothened by a copter instrument and using a vibrator during
casting.

B4.1 Slabs Concrete: Provide all materials and cast reinforced concrete(ready mix C 25) for the
building slab, fair-faced beams, Tie beams, stairs, lintels, and windows decorate 18cm thick,
with all the required works. The price includes casting the parapet of the slab and laying a
layer of XPS foam board 3cm thick (high density, not less than 25 kg /m3) before casting the
concrete.
Note: All the roofs must be treated and smoothened by a copter instrument and using a
vibrator during casting.
M3 535
B4.2 Beam using concrete compressive strength C30 for 28 days.
M3 140
B4.3 Lintel using concrete compressive strength C20 for 28 days.

M.L. 158
B4.4 Up stand using concrete compressive strength C30 for 28 days.

M3 16
B4.5 Staircase and Ramp using concrete compressive strength C30 for 28 days.

M3 40
B4.6 Decoration Louvers using concrete compressive strength C30 for 28 days.

M3 32

2
 # Item Description Unit Quantity
B4.7 Expansion Joints: Provide materials and construction of Expansion joints both vertically and
horizontally for walls and ceilings using Hypalon tape plus Epoxy paste(Sagging vertical type)
with a width of tape 15 cm and 1.5mm thickness. The price includes using a special 18 cm
width Aluminum sheet or stainless steel brackets with elastic (intermediate rubber) inserts.
Styrofoam, using special pasty mastic according to the details and instructions of the site
engineer with all necessary materials and works for fixing. (The measurement will be done
Horizontally {Horizontal projection from roof}).
M.L. 22
C Masonry works: Including provision of material, erection, pointing, curing, making expansion joint every
(6m) with thickness 25mm with using of 25mm thickness compressed Polystyrene sheets, all necessary
work according to section (500) of I.G.T.S., drawings, and instructions of the site engineer.

C1 Solid Concrete Block Work: Supplying materials & construction of walls with solid concrete
blocks (20x20x40) cm. and cement sand mortar (1:3). The work should be done according to
the specifications, drawings, and instructions of the site engineer.
M3 56
C2 Hollow Concrete Block Works (For Internal/Partition Walls): Supply materials & construction
of walls with hollow concrete blocks 20 X 20 X 40 cm with cement mortar(1: 3) for the
internal/partition walls the price includes filling the vertical joints between blocks by cement
and sand 1:3. The work should be done according to the specifications, drawings, and
instructions of the site engineer.
M3 430
C3 Hollow Concrete Block Works (12 X 20 X 40 cm): Supplying materials & construction of walls
with hollow concrete blocks 12 X 20 X 40 cm with cement mortar(1: 3) for necessary walls, the
price includes filling the vertical joints between blocks by cement and sand 1:3. The work
should be done according to the specifications, drawings and instructions of the site engineer.
M2 30
C4 Clay Bricks Works (For External Walls): Supplying materials and construction of walls with
load-bearing clay bricks (20 X 20 X 40 cm) (INTERLOCKING TYPE) weight not less than (14Kg),
with cement mortar(1: 3) for above D.P.C level the price includes filling joints vertically by
cement and sand 1:3 and fixing the space with concrete columns by G.I. metal holdfast 30cm
long 4mm thick at every alternative course fixed to concrete columns with two nos. shot fired
cramps.

M3 470
C5 Concrete Block Works (For Parapet): Supply material and build walls with hollow concrete
blocks (15x20x40) cm. and cement sand mortar (1:3) for parapets, according to specifications
and instructions of the site engineer.
M2 230
D FINISHING: Including provision of all necessary materials, work, and curing. The works should be done
according to sections 10, & 14 of I.G.T.S., drawings and instructions of the site engineer with all necessary
works, and use SBR at a rate of 200gr per m², the ratio of SBR to water(3-1).

D1 Cement Plastering: Providing materials and plastering with cement sand mortar 1:3 three
layers (1. cement spatter dash(sharbat),2.rendering coat and levelling (kafmal),3. finishing fine
coat (saf) ) 20mm thick min. and the final layer should be very smooth, using 3m aluminium
straight edges for plastering guides for outer walls, main entrance, balcony, and corridors.
And use SBR at a rate of 200gr per m2. The price includes fixing steel wire mesh for the edges
between walls and columns.

M2 2,500
D2 Gypsum Plastering: Supplying materials and plastering with gypsum in 2 layers with a
minimum thickness of 20mm using aluminium straight edges for plastering guides, each 80
cm for walls and roofs, corridors, and entrance hall, and the area indicated in the drawings.
The price includes spreading cement splatter dash and using SBR for the outer wall, fixing
steel wire mesh for the edges between walls and columns, and then using one layer of
cement plastering to cover the wire mesh.

M2 2,850

3
 # Item Description Unit Quantity
D3 Wall Tiles (Porcelain): Supply materials and erect Porcelain Tiles for the wall with dimensions
(60x30 cm) and (6-10 mm) thickness (sample should be provided for approval and will
selected by the supervisor Engineer) for the Kitchen and WASH facilities and water drinking
place. Acid-resistant, Low water-absorption 0.5% with all necessary works on a cement sand
mortar 1:3 mix ratio layer and using a proper adhesive. The price includes fixing the metal U
Shape Profile Stainless Steel Edge Trim for the edge and corner and cleaning the porcelain
after the end of the work. The work includes using flex-type grouting to seal the joints; all
required work should be done according to the attached drawing and the supervisor
engineer's instruction.

M2 690
D4 Skirting: Supply materials and skirting in rooms using porcelain tiles (15 cm height) and tile
adhesive materials ( flex type) according to the drawings and instructions of the site engineer. M.L. 780
D5 Oil Painting: Provide materials and Painting 120 cm Height using oil paint (colour approved by
the site engineer), two layers (Matte light colour), and 3 layers 1.2 m high for the classrooms
and the corridor.
M2 1,700
D6 External Painting( silicone): Provide materials and Painting with External painting.
Weatherproof three layers for the areas indicated in the drawings (for exterior walls).
Note: Products must be ISO 9001 certified for quality management.
M2 2,500
D7 Acrylic Internal Paint: Provide materials and Painting with Acrylic painting in three layers for
the rooms, corridors, and areas indicated in the drawings (inside the building) or indicated by
the site engineer.
Note: Products must be ISO 9001 certified for quality management.
M2 2,850
D8 Decoration Stone: supply materials and erection of Decoration artificial outdoor stone (as
sample approved) using (approved colour) for an indicated place in elevation drawings, using
special glue (Kalakim) for fixing above rough cement plaster and filling the joints, according to
specifications and instructions of site engineer.
M2 70
D9 Suspended Ceiling Tile: Provide materials and fix acoustical panels 60 X 60 cm, fire rate Class
A, edge SLT model for all rooms and corridors inside the building (except WC and Kitchen).
The price includes hanging beams (Skka 38 mm height) every 120cm by screw, steel fisher,
rode 3mm, connecting the beams by Skka 120cm,60cm long (32mm height ), and all
necessary works.
M2 1,300
D10 Plastic Suspended Ceiling Tile: Provide materials and fix Plastic false ceiling 60 X 60cm for the
places that the site engineer indicates. The price includes hanging beams (Skka 38mm height)
every 120cm by screw, steel fisher, rode 3mm, connecting the beams by Skka 120cm, 60 cm
long (32mm height ), and all necessary works.
M2 260
D11 MDF Wooden Panels: to protect the walls with 18mm thickness and 15 cm Hight for
classrooms; the price includes fixing the wall by using screw bolts, each 30cm and covering
the hole with a proper sticker.
M.L. 300
E Doors & Windows: Providing all necessary materials and installing doors according to sections 11, 12,
and 13 of I.G.T.S, details, and instructions of the site engineer with all necessary works. Prior samples
should be approved by the site engineer.

E1 Composite Doors: Providing and installing standard decorative Composite wooden doors HDF
Laminated thermoformed sheet water and coloured made,200 mm minimum frame
thickness and 100mm cornice outer measurement, double faces wooden plywood, each face
8mm thickness, the sample should be provided for approval, The price includes installing 6
mm glass pans with frames, switch, gate lock, hinges, rubber, door stopper, and wooden
frames. M2 72
E2 Aluminum Doors Works: Supply material and install Aluminum doors 2mm thickness double
plate. The price includes a double glass pan of 6mm thickness, ordinary or mushajar, rubber,
handle, switch mortice, and door stopper.
M2 110

4
 # Item Description Unit Quantity
E3 Aluminum Windows: Supply material and install Aluminum windows wide section 6cm, 2mm
thickness, Double glass pan (6mm+4mm ) thickness, ordinary or mushajar, rubber, handle, the
price includes flywire mesh for opening Areas, the work includes cleaning the glasses by
machine before composing.

M2 270
E4 Decorative Metal Door Works(Qasa): Provide and install decorative metal doors (Qasa),
including upper half window glass with the frame for the entrances and halls, double-faced of
plate thickness 1.50mm including glass pans, door frame 13.5*4.5cm 2.5mm thickness, Film
Coated Residential Steel Entrance Door Glassy Finished Style, including special switch, gate
lock, door stopper, rubber, polycarbonate filled, special guard bar, thermal paint & metal
frames 6*22cm, Mercury glass 15x40cm with 3 cm Styrofoam polystyrene inside the door,
Central lock system, with additional horizontal a lock with three concealed hinges with all
necessary works, samples required for final approval.
M2 20
E5 Metal handrail Works For Staircase: Provide materials and install a handrail for the stair with
a height of 85cm for the Administration sector stair. The price includes fixing Jawe wood by
screw and using sperto, Varnish due to details, painting all the ironmongery with 2 layers of
anti-rust and 3 layers of oil paint.
M.L. 70
E6 Steel Guard Bars: Provide and install metal guard bars windows, using square corrugated bar
12 x 12 mm welded inside an angle frame 1.25"*1.25"*3mm, fixed by screw and fisher to the
wall. The price includes painting all the ironmongery with two layers of anti-rust and three
layers of oil paint
M2 270
E7 Marble Windows Frame: Provide materials and cover the windows frame (four sides) with
marble 2cm thick, width 30cm, the price includes spin-off the outer and inner face edges of
the granite and using kalakim paste FLEX type for fixing.
M.L. 590
E8 Steel ladder: Providing materials and fixing steel ladder using square pipe 2.5" for the edge
and 2"(thickness 1.5 mm) for the interior. The price includes painting all the ironmongery with
2 layers of anti-rust and 3 layers of oil paint
M.L. 15
E9 Metal handrail Works For the Walkways: Provide materials and install handrails on both
sides of the entrance (walkway) with 90 cm height; the price includes excavation concreting
(with dimensions 30*30*50 cm ) for fixing square steel pipe 3'' x 3'' each 2m welded to the
metal handrail. The price includes painting all the ironmongery with 2 layers of anti-rust and 3
layers of oil paint
M.L. 40
E10 Room Address: Supply materials and equipment to print the room's address on a wooden or
plastic plate (30x15)cm and fix it to the allocated room's wall. All required work should be
done according to the instructions of the supervisor Engineer.
No. 26
E11 Whiteboard: Supply and install whiteboard (1.2*2.4)m fixing to the wall by bolts according to
Ministry of Education standards.
No. 15
E12 Sign board: Supply and install steel sign board (2.5mX1.5m) plate gage 18, with steel angle
frame (1.25x1.25) inch (3mm) thickness, including printing the name of the school with the
foundation year by detail. The price includes painting all the ironmongery with 2 layers of
anti-rust and 3 layers of oil paint
Pcs 1
F Flooring: (Including provision of materials, works, curing, and installation) The work should be done
according to sections 6 and 9 of I.G.T.S. drawings, and instructions of the site engineer with all necessary
works.

5
# Item Description Unit Quantity
F1 Porcelain Floor Tiles: Supply materials and paving mat Porcelain Floor Tiles 60x60 cm 14mm
thickness (sample should be provided for approval) Wear-resistant, Non-slip, Acid-resistant,
Low water-absorption 0.5% with all necessary works on a layer of cement sand mortar 1:3 mix
ratio, The price includes repolishing the tiles after the end of the works. The work consists of
using cement mortar and sealing the joints with white cement and lime grout (SPR colour if
required mixture), making a 1.0 cm expansion joint, and filling each 25m2 with a flexible
epoxy.

M2 1,700
F2 Natural Granite Tiles: Supplying materials and covering the staircase and entrance with
Natural Granite 3cm thickness (approved sample) with cement sand mortar 1:2. The price
includes cement splatter dash, with additives using a (1:2) solution of water and bonding
agent(SBR concentrated %48 ), the measurement will be done considering tread and riser.

M.L. 70
F3 Natural Granite Tiles: Supply materials and paving Natural Granite 2 cm thickness (approved
sample) with cement sand mortar 1:2. The price includes cement splatter dash, with additives
using a (1:2) solution of water and bonding agent(SBR concentrated %48 ).
Note: The ratio of mixing water and SBR is 1:3

M2 51
G EXTERNAL WORKS: Apron, walkways (inside the building and outside the building), fence according to
specification, attached drawings and instructions of the site engineer.

G1 Excavation works: Excavation in all types of soils(rock, asphalt, concrete), including backfilling
and compaction according to the requirement of section (3) of I.G.T.S. for the foundation.
The price includes compaction of the base of excavation using a roller vibrator, according to
the details and instructions of the site engineer.

M3 90
G2 Crushed gravel works: Supply material and lay crushed gravel 10 cm thick with good
compaction for foundations.
M2 204
G3 Plain concrete for foundation: Supply materials, equipment, and skilled labour for casting
plain concrete with a Compressive strength of 28 days 210 kg/cm2 (1:2:4). The work includes
formworks using steel pipes shuttering, grading and levelling smoothing the surface with a
handheld vibrator.
M3 60
G4 Solid concrete block works: Supply material and construction of walls with solid concrete
blocks 15X20X40cm with cement and sand mortar(1: 3) for walkways, aprons, and stand of
water tank according to details. The price includes flush pointing for outside and inside by
cement sand 1:3.
M3 80
G5 Concrete for entrance walkway and Apron: Supply materials and cast plain concrete 15 cm
thick above 10cm thick compacted crush gravel for the side walkway and apron area with
expansion joint at 2.5m. The work includes grading, levelling, compaction of the foundation
soil, and smoothening the surface of the concrete. According to the details, straight steel
shuttering should be used for joints, as shown in the drawings.

M2 915
G6 Parking Concrete (15cm thick): Providing materials and reinforced concrete 21 Mpa (Smooth
surface using concrete surface screed vibrator machine and copter instrument ) for parking
area thickness 15cm with laying of 10mm steel bars at (30*30) cm spacing c/c making
expansion joints every 2.5m in both direction or as required by cutter instrument filling the
space by epoxy, the price includes using levelling steel forms for the edges. The price includes
laying two layers of thick nylon before casting the concrete.

M2 385
G7 Cement plastering: Supply materials and plastering with cement mortar 1:3 two layers
( kafmal, saf ) thickness 20 mm. Min., and using a straight edge (the final layer should be very
smooth). using 3m straight aluminium.
M2 420

6
# Item Description Unit Quantity
G8 Plastic Painting Works: Provide material and painting with 3 layers of Acrylic Type Painting
above the outside and decorations as indicated by the site engineer. The work includes
treatment and smoothening of the broken, honeycomb or scratched areas with cement-
powder paste before painting.

M2 420
G9 Play yard Concrete (15cm thick): Supply material and pave the play yard area using 15cm
thick concrete with a smooth, levelled surface, using concrete with a compressive strength of
21 Mpa, having for 28 days with a layer of BRC 6mm 15*15cm c/c expansion joints in both
directions according to the instructions of the site engineer and drawings. Make the layout of
the yard using oil paint and over a layer of 10 crushed gravel. You must use a helicopter and
grinding.

M2 1,000
H Fence:
H1 Excavation works: Excavation in all types of soils (even rock layers or existing foundation
concretes and asphalt layer, if any), including backfilling and compaction according to section
(300) requirements of I.G.T.S. The price includes compaction of the base of excavation
according to the details and instructions of the site engineer.

M3 130
H2 Crushed gravel works: Supply material and lay crushed gravel 10 cm thick with very good
compaction for foundations.
M2 204
H3 Reinforced concrete for foundation: Supply materials, equipment, and skilled labour for
casting reinforced concrete with a Compressive strength of 28 days C25. 8 No. Ø12 mm top
and bottom and stirrup Ø10 mm@30 c/c,30cm thickness and 60cm width, The work includes
formworks using steel pipes shuttering, grading, levelling, and smoothing the surface with a
handheld vibrator.
M3 62
H4 Solid concrete block works: Supply material and construction of walls with solid concrete
blocks 15X20X40cm with cement and sand mortar(1: 3) for the fence, and stand of water tank
according to details. The price includes flush pointing for outside and inside by cement sand
1:3.
M3 85
H5 Hollow concrete block works: Supply material and construction of walls with Hollow concrete
blocks (20X20X40)cm with cement mortar(1: 3) according to details. the price includes filling
the vertical joints between blocks with cement and sand 1:3.
M3 180
H6 Cement plastering: Supply materials and plastering with cement mortar 1:3 two layers
( kafmal, saf ) thickness 20 mm. Min., and using a straight edge (the final layer should be very
smooth). using 3m straight aluminium.
M2 1,750
H7 Plastic painting works: Provide material and painting with 3 layers of Acrylic Type Painting
above the outside and decorations as indicated by the site engineer. the work includes
treatment and smoothening of the broken, honeycomb or scratched areas with cement-
powder paste before painting.
M2 1,750
H8 Metal door for main gate: Provide materials and install metal door m with two face plates
(plate thickness 1.25mm) for the main gate, primer + three layers oil paint and two layers of
anti-rust for all ironmonger as required, switch mortise, metal frames, and decoration. The
price includes construction of to reinforced using concrete compressive strength 26 Mpa for
columns(40x40)cm to fix the door. The price also includes casting reinforced using concrete
compressive strength 21 Mpa for the foundation of the columns (0.7x0.7)m on a layer of 10
cm well compacted crushed gravel, with all necessary work according to specifications, the
details and instructions of the site engineer.
M2 25
H9 Supply material and fixing decoration iron steel for in front of the fence with section and must
be anti rusted two layers and three layers of oil painted and all necessary according to
specifications, the details and instructions of the site engineer.
M2 110

7
 # Item Description Unit Quantity
H10 Screened Loam for Garden: Provide materials and lay a layer not less than 25 cm thickness of
approved screened Loam for the garden. The price includes gracing all areas, levelling,40 no
of (rubina tree), 30 no of (sarwdi 3amudi tree ) and 50 no of (shmshady saw u zard)
according to instructions of the site engineer (THIS ITEM QUANTITY USING JUST IN
NECESSARY AREA).
M2 1,400
2 Electrical Works:
I Electrical Installation Works :
Electric works including provision, installation and testing of all the electrical materials, the
implementation should be according to the standard, I.G.T.S. (section 1600) and the
drawings.
Note :
1- PVC pipe system: Electric points including provision, installation and testing of all (PVC
Pipe, cables, fittings, metallic boxes, switches …etc.).
2- Before using any materials the contractor should submit samples for approval by the
Engineer.
3- All (PVC pipe wires) size (2x1x2.5)mm², (3x1x4)mm².
4- All switches for lighting should be.

I1 Main Distribution board according to the drawings contain: contains 2 number circuit
breakers 250A 3ph, one KW meter with C.T.250/5, and one number manual change over No. 1
400A
I2 Sub Main Distribution Board (S. M. D. B.) as per the drawings, including:
a-Providing and installing one metal box with dimensions (60x100x25) cm. as shown on the
drawings, with door and switch-lock, made from metal plate (Gauge 18), painted with a layer
of anti-rust and two layers of grey colour oil paint with all necessary fitting and accessories.
b- One circuit breaker (250) A., (3)-ph
c- One circuit breaker (110) A., (3)-ph
d- One circuit breaker (63) A., (3)-ph
e- Two circuit breaker (40) A., (3)-ph
f- Two circuit breaker (10)A..(3)-ph
g- Bulb indicator for (3)-ph, (3) No.
h- One voltmeter (0-500) V. No. 1
I3 Final Distribution Boards (F.D.B.) Circuit Breaker as per the drawings:
a- (Final Distribution Board type A )-3-ph according to drawing No. 1
b- (Final Distribution Boardr type B,C,D)-3-ph according to drawing No. 3
c- (Final Distribution Boardr type E)-3-ph according to drawing No. 1
I4 Supply materials, install, connect, and test electrical LED lights (60x60cm)(50-80 W) with all
annexed parts using (2x1.5)mm2 wires inside false ceiling (daylight type) with switch on/off all
(2-3) lamp controlled by one switch.
No. 268
I5 supply and installation of Ceiling Lamp waterproof IP 65 for outside (60) watt, type (circular). No. 66
I6 supply and installation spotlight for ceiling (18) watt, type (circular). No. 32
I7 supply and install an LED projector for outside lighting (100-watt). No. 14
I8 supply and installation Switch-plug (13)Amp.

No. 74
I9 supply and installation of Grid Switch (32)Amp. With 3*1*4 mml2 and all requirements

No. 40
I10 supply and installation of Main bell with push button

No. 2

8
# Item Description Unit Quantity
I11 Supply, install, and test electric Ceiling Fan with the regulator. The price includes installing the
electrical points by isolation copper wire 1.5 mm2 and 10mm steel bar for hanging the fan
according to the instructions of the supervisor electrical engineer.

No. 53
I12 supply and installation Exhaust fans: Size 12".

No. 2
I13 supply and installation Exhaust fans: Size 6". No. 9
I14 Supply, install, and test ventilation turbine Exhaust Fan size(8"). The price includes supplying
& and installing 6" PVC pipes to be used as ducts and 6 diffusers with all the required
electrical works(cable, control switch, etc.).
Set. 4
I15 The main cable and outdoor cables should be armoured whenever laid in the ground, The
cost includes the provision of PVC pipes of diameters not less than four times the diameter of
the cables with PVC manhole 60 x60 according to drawings. Each cable must be in a separate
pipe surrounded with sand. The item includes all requirements.All indoor cables must be
pulled inside the cable tray from SMDB to FDB The item includes all requirements

a-Supply and installation main cable1*95mm2 11kv armour according to MOE specification ,
between the electrical source and Tr.room
M.L 90
b- Supply and instalation of Main Armourd cable 4(1X150)mm2 + 1x 70 mm².

M.L 120
c- Supply and installation Armourd Cable 4x 35+1x 6 mm² .

M.L 25
d- Supply and installation of Cable 4x 16+1x 10 mm².

M.L 50
e- Supply and installation of Cable 4x 10 +1x6 mm² .

M.L 60
f- Supply and installation of Cable 4x 4+1x4 mm².

M.L 100
g-Supply and installation of Armourd Cable 3*6mm2 for Pumps.

M.L 45
I16 A- Supply and installation of cable tray 10cm.

M.L 45
B- PVC manhole 60 x 60 for Maintenance.

No. 4
I17 Provide and install electrical pole size(4") dia., (6) meter length, with accessories according to
the drawings.
No. 1
I18 Supply, install, and test a split AC unit (24,000 BTU) (inverter technology and Ampere
Control); the work also includes installing a 32-amp Amp residual current circuit breaker with
overcurrent protection (RCBO) and connecting it with the electrical source using (2X4) mm2
cable with all accessories. The price also includes fixing PVC 3'' pipe with slab casting making
the parapet around and filling the hole with foam and adequate cover. The price includes
fixing and suspending the outdoor unit on the wall or making a proper steel stand.

No. 14

9
# Item Description Unit Quantity
I19 Supply, install, and test a split AC unit (36,000 BTU) (inverter technology and Ampere
Control); the work also includes installing a 32-amp Amp residual current circuit breaker with
overcurrent protection (RCBO) and connecting it with the electrical source using (2X4) mm2
cable with all accessories. The price also includes fixing PVC 3'' pipe with slab casting making
the parapet around and filling the hole with foam and adequate cover. The price includes
fixing and suspending the outdoor unit on the wall or making a proper steel stand.

No. 2
I20 Earthling system contains (3 pieces of pure Cu rods ) delta connection connected by
(1x70mm2) Cu wires according to Drawings through Cu clamps to the Transformer & other to
the(M.S.B) then according to drawings to(S.B) inside the building, the rod should be buried in
the excavated hole of 0.4x0.4m, 3 m depth then backfilled by ( 10 layers of coarse salt & coal )
with required manhole covered by 40x40cm cast iron.

No. 1
I21 Supply, install, and test Stainless steel Drinking water cooler min 100 litres,4 taps Compressor
capacity ¾ hp. the price includes the connection with the water source using water pipes of
OD 25 mm, PN 16 with all fittings and accessories, excavation (required depth), and
backfilling 10cm of clean soil with all necessary works. Also, the electrical connection using
wire (3*2.5mm²).
No. 3
I22 provide install and test lightning protection arrestor,(active) partner ESE-SAT 1000 type, the
top of the building, the price includes installing Galvanized iron pipe 3" 5 m and connecting it
with special earthing system(3 copper Rod) and connecting all together with cable 2*50 inside
PVC pipe.
L.s 1
I23 Electrical Water Pump: Supply and install an electrical water pump according to the following
specifications. The price includes all required electrical cables 3x4 mm2 (up to 50m). The
cable must be put into a PVC pipe and laid in a trench with dimensions 30 X 40 cm, then the
backfilling with 10cm clean sand, 20cm clean soil, and 10cm ordinary Concrete. switches,
pipes, water automatic PRESSURE SWITCH accessories, connection with the school, and a
small steel protection pump room as indicated in drawing details:- Size: 1.5" and H.P. = 1.5.

Unit 2
I24 Supply, install, and test a 200-litre production storage capacity electrical water heater with a
2000-watt thermostat. The tank plate is galvanized and 3mm thick. The work also includes all
wiring, 4x3mm2 and a 30 Amp electric switch, plumbing works, pipes, fittings, and fixtures,
which are complete in all respects.
Unit 2
I25 Supply, install, and test a 60-litre production storage capacity electrical water heater with a
2000-watt thermostat. The tank plate is galvanized and 3mm thick. The work also includes all
wiring, 4x3mm2 and a 30 Amp electric switch, plumbing works, pipes, fittings, and fixtures,
which are complete in all respects.
Unit 7
I26 Supply, install, and test cable size 2 X 4mm2+ control switch with photocell to collect and feed
external lamps thrown inside 25mm diameter PVC pipes in the ground + installing above cable
tray with all required and necessary works (such as hidden manholes) above dimension (40 X
40)cm.
Ml 100
I27 Supply install, and test split AC points using copper cable 4x6mm2 inside PVC pipe with
electric switch 45 Amp, with using mini 32x3 Amp +10Amp with box, also install 3/4'' PPR pipe
inside the wall with fixing it to drain the water of split outside the building.
No. 24
I28 Optical smoke detector No. 40
I29 Manual Call Point No. 6
I30 Indoor siren with flasher No. 10
J Installing Sound System+Data Show+Printer
J1 Supply, install, and test an amplifier 240 watts (DVD+USB+FM)with all the required works and
connections.
Unit 1

10
# Item Description Unit Quantity
J2 Supply, install, and test a loudspeaker 40-watt wall with headphones 2x2.5mm in a plastic
channel. The price includes all the required.
unit 4
J3 Supply, install, and test microphone control. Unit 2
J4 Supply, install, and test, the microphone stand(tabletop). Unit 2
J5 Supply, install, and test Data Show (TV+USB+HBM+VGA). The price includes all necessary
works according to the instructions of the site engineer. Unit 1
J6 Supply, install, and test Data Show Screen (230x220)cm2 LED electric control type. The price
includes all necessary works according to the instructions of the site engineer. Unit 1
J7 Supply and install a Data Show Base 1.5m in length with all necessary works according to
instructions of the site engineer. Unit 1
J8 Supply and install Data Show Cable 25mm (VGA/HDM) with all necessary works according to
instructions of the site engineer.
Unit 1
J9 supply install and test printer model Resolution Reading: 600dpi × 600dpi
Copying: 600dpi × 600dpi
Printing: 600dpi × 600dpi, 1200dpi x 1200dpi (UFRll-LT only)
Number of Tones: 256 Gradations. The price includes installing a table for papers, with a year
warranty, with all necessary works according to instructions of the site engineer.
Ls 1
K Installing Transformer 100 KVA
K1 Supply, install, and test an Electric transformer of 100 KVA Indoor; the price includes
transferring. Test certification card from Erbil's Electric distribution directory, iron channels,
cable stand, and connection to the electric power.
NOTE: The price includes the construction of a room (4x5)m with all the required (concrete
block work, reinforced concrete, cement plastering, painting, doors, windows, etc.)according
to the plan of the Directorate of Electricity.
Unit 1
K2 Supply, install, and test electric board 25 X 80 X 100 cm by iron plate thickness,2mm with
door and painting which contains bus bars 250Amp, circuit breaker 250 A fence type 3pole,
kWh 200/5A, multi measurement digital type, C.T 200\5 A, signal lamp,3*2A circuit breaker,
and all accessories according to supervisor engineer.

Unit 1
K3 supply, install high tension electric pole 11m GV lattice-type. The price includes iron angle
channels, a Linked fuse 12Kva, a lighting arrestor 11kv, and 10kva excavation concrete work
with all accessories.
Unit 3
K4 supply, install 11m high voltage electric pole tubular GV. The price includes excavation,
concrete work, pin insulators, and all accessories.

Unit 6
K5 supply, install and test high voltage cable 11kv XLP 3 X 150mm² 15-20kv with PVC pipe Iron
clamp two final Joints(Ryckom), excavation, Filling, tiles and concrete work.
Ml 60
K6 supply, install and test insulated copper cable 1 X 95mm² double PVC cover the price includes
cable shoes and (GV) Iron bolts.
Ml 60
K7 supply materials and doing Earthing system protection by copper rod 1.5m with a diameter of
18mm. The price includes copper bar conductor 1 X 50mm2 improving Earthing soil materials,
and all accessories to complete this item.
Unit 3
K8 supply, install, and test ACSR conductor 120mm² the price includes insulators and
connectors.
Ml 300
K9 supply install and test automatic change over switch 250 amp. The price includes a suitable
board (140 X 90 X 40)cm the contactors are connected with bus bars and contain timers,
control circuit breakers, a phase failer for main power, and copper insulated cable 1 X 300
mm² to complete the item.
Unit 1

11
 # Item Description Unit Quantity
K10 Supply, install, and test lightning conductor protection systems with all the required works
and accessories.

Set 1
K11 supply, install and test the final distribution circuit breaker 4 Fuse with cable 3 x 4mm² in the
transformer room.
Set 1
K12 supply, install and test copper cable 70mm with all the required works.
Ml 40

3 Mechanical Works:
L Sanitary (Plumbing) Installation: Includes supply and installation of materials, pipes, all kinds of fittings,
valves, mixers, bibcock taps, P-traps, gullies with cover, supports, hangers, plug and clips, all excavation
with backfilling, placing concrete 1:2:4,15cm thick under and around pipes, manpower for the installation
and internal connection of the water system to hot and cold water and the main water supply system. All
water pipes should be Polypropylene (PPR) Composite water pipes of min. 3 Layers side walls
(PPR/AL/PPR/PE), PPR-C inner layer, and a special mixture of AL middle layer and should be coated with an
external layer of PE (Polyethylene Layer) dark grey/black colour to protect against ultraviolet rays,
Different Outside Diameter (OD) as below, Min.PN16 Bars, suitable for drinking purposes/food grade,
approved samples with all required fittings and accessories, PVC pipes for sewerage system with all
required fittings. All new WS and SS work items should be tested before covering. Note: All materials
should be approved type. The work of the external water connection (3/4" dia.) includes repairing (if any)
all Asphalt, concrete, and curb stone.

L1 Drinking Water Supply Works

Providing and installing polyethene pipe (HDPE) SDR11 PN 16 RC with all required accessories
such as ( valves, fittings, hangers, Anchors....etc) for cold and hot water plumbing system as
shown on the drawings, the price includes connecting pipes, fittings, accessories, necessary
excavation and backfilling works, placing concrete under and around pipes and connecting
the system to Municipality Water Supply Network outside of project site boundary, also
includes repairing (if any) all Asphalt, curbstone or concrete surface that demolished or
damaged during excavation. All the work must be executed under the instruction and
guidance of the supervisor engineer, All pipe diameters are represented by outers according
to the HDPE pipe catalogue as follows & pressure PN16 (SDR11), supplying the above items
should be genuine and from the origin source and provided with product guaranty certificate.
Before installing and fixing the water plumbing system samples from each diameter of the
provided quantities of the pipes should be laboratory tested and under the site engineer's
guidance.

Tests of not less than 24 hours each should be applied to water line systems before covering
the pipes and complete finishing; First, by filling whole HDPE pipelines with water and
standby for 24 hrs to disclose any visual or unseen leakages. The second action; is applying
pressured water-air testing (using a compressor) to make sure that HDPE joints are
completely sealed and locate leaks if any. after finishing the work, pipe systems should be
cleansed by chlorine treatment 50 parts per million. All the above work and tests are
executed under the site engineer supervisor.

L1.1 ø25mm

M.L 177
L1.2 ø40mm

M.L 101

12
 # Item Description Unit Quantity
L1.3 ø50mm

M.L 65
L2 Providing and installing Pressure Composite pipe PP-RCT (Aluminum foiled ) and
(Reinforced fibreglass) type pipes with all required accessories such as ( insulation, cladding,
valves, fittings, hangers, Anchors....etc) for cold and hot water plumbing systems as shown on
the drawings, the price includes connecting pipes, fittings, insulation, cladding, accessories,
necessary excavation and backfilling works, placing concrete under and around pipes and
connecting to the HDPE system. All the work must be executed under the instruction and
guidance of the supervisor engineer, All pipe diameters are represented by outers according
to the PP-RCT pipe catalogue as follows & pressure PN20 (SDR6), The pipes should comply
with the standard measurements (DIN8077, DIN8078, DIN16962, DVGW, EN ISO 15874, TSE )
for plastic piping system for Hot and Cold Installation works .supplying the above items should
be genuine and from origin source and provided with product guaranty certificate. Before
installing and fixing the water plumbing system samples from each diameter of the provided
quantities of the pipes should be laboratory tested and under the site engineer's guidance.

Tests of not less than 24 hours each should be applied to water line systems before covering
the pipes and complete finishing; First, by filling whole PP-RCT pipelines with water and
standby for 24 hrs to disclose any visual or unseen leakages. The second action; is applying
pressured water-air testing (using a compressor) to make sure that PP-RCT joints are
completely sealed and locate leaks if any. after finishing the work, pipe systems should be
cleansed by chlorine treatment 50 parts per million. All the above work and tests are
executed under the site engineer supervisor.

L2.1 ø20mm M.L 133

L2.2 ø25mm M.L 128
L2.3 ø32mm M.L 114
L2.4 ø40mm M.L 30
L2.5 ø50mm M.L 30
L3 Sewage and Waste Water Works
Providing and installing 6 bars Wavin SiTech+ U-PVC Waste pipes and fittings for
implementing sewerage system as shown on the drawings for both types of pipes (B and BD)
for internal and external places, and the thickness of the smallest diameter pipe should not
be less than 4 mm with SN4 as Ring Stiffness The price includes fittings, accessories, laying,
jointing, necessary excavation, backfilling, placing concrete 1:2:4 under and around pipes,
and connecting the pipes with manholes as shown on the drawing. All works must be under
the instruction and guidance of the supervisor engineer supplying the above items and should
be genuine and from a source and provided with a product guarantee certificate. the work of
external water connection HDPE 200mm dia with SN8 as ring stiffness ratio ) includes
repairing (if any) all Asphalt, curbstone or concrete surfaces that were demolished or
damaged during excavation. Before installing and fixing the wastewater plumbing system
samples from each diameter of the provided quantities of the pipes should be laboratory
tested and under the site engineer's guidance. The pipes should comply with the standard
measurements (, EN ISO 15874, TSE, EN 1451, TS 275-1, EN 1329-1, DIN 19531 ) for plastic
piping systems for the waste system

13
 # Item Description Unit Quantity
Tests of not less that 24 hours each should be applied to sewage system pipes before
covering the pipes and complete finishing; First, by filling whole PVC pipelines with water and
standby for 24 hrs to disclose any visual or unseen leakages. The second action; is applying
pressured water-air testing (using a compressor) to make sure that PVC joints are completely
sealed and locate leaks if any. After finishing the work inside pipes should be cleaned of any
debris and dirties. All the above work and tests are executed under the site engineer's
supervision.

L3.1 ø50mm M.L 38

L3.2 ø75mm M.L 50
L3.3 ø110 mm M.L 105
L3.4 ø150mm M.L 40
L3.5 ø200mm M.L 58
L4 Providing and installing 6 bar PVC pipe for the Ventilation system, all works must be under
the instruction of the supervisor engineer and according to drawings. All works must be under
the instruction of the supervisor engineer the specifications of these pipes are the same as
explained above in Article 2. A Ventilation Cowl (grill) should be used at the top of the vent
pipes.

L4.1 ø 50mm M.L 75

L5 Stormwater piping (Vertical Rain Water Drainage)
Providing and installing galvanise pipe Ø 4" (Inch) for Rainwater drainage from the roof. the
price includes fittings, accessories, laying, jointing, clamps, necessary excavation and Spouts
for snow areas. All works must be under the instruction of the supervisor engineer. The end
of the pipeline for each rain drain should be connected to the elbow 45 degrees on the floor
under the site engineer's supervision. Note: Any undesired or improper rainwater outlet
connected to the storm pipe in the slab concrete, should be extremely avoided.

L5.1 Galvanise Seel pipe ø 4"( Inch) M.L. 40

L6 Providing and Installing Ceramic Wash Basin, white vitreous, self-contained overflow,
Dimension (60x50)cm, including all accessories such as ( water flexible high-pressure stainless
steel hoses 1/2" with chromium plated stop Valves for cold and hot water and completed
with flow drain flexible hoses( p trap) and supporting brackets properly fastened with screws,
nuts, washers & anchors,….etc ). a sample will be presented to the site Engineers for approval
before supply and installation.
No. 14
L7 Providing materials and fixing industrial marble wash basin with heavy-duty mixer each 2
meter (sample should be provided for approval) + floor drains + Gully (Trap), with aluminium
kitchen cabinet, doors and drawers, well decorate design, including all accessories such as
High-pressure flexible drain pipe, supporting brackets, properly fastened with screws, nuts,
washers & anchors,….etc ), the price also includes an aluminium frame with four castors to
hold the whole cabinet on. A sample will be presented to the site Engineers for approval
before supply and installation.
M.L. 4
L8 Providing and Installing Chrome Stainless Steel Mixer for cold and hot water for washing
basins & Kitchen Sinks and benches of the science labs with all attached hose hangers and
bolts and any required fixtures. A sample will be presented to the site Engineers for approval
before supply and installation.
No. 16
L9 Providing and installing stainless steel water taps 1/2" Inch, durable strength, for student
water drinking fountains and Gardens and W. C . This item includes all necessary fittings and
accessories. Teflon tapes are used for thread connections.
A sample will be presented to the site Engineers for approval before supply and installation.
No. 24

14
 # Item Description Unit Quantity
L10 Providing materials and fixing Eastern W.C. Ceramic with hidden Siphon/in-wall tank. + Gully
(Trap) and cleanout accessories. The work should be done according to the site engineer's
specifications, drawings, and instructions.
No. 12
L11 Providing and installing white vitreous (WPD) Ceramic W.C Western type (Built-in flush tank)
for students and teachers with a disability, including gully S-trap, water shut off valves
chromium type1/2", self-contained cleansing faucet, expansion bolts, clamps, all needy
accessories and fittings for fixing the bowl, and pipe connection work. A sample will be
presented to the site Engineers for approval before supply and installation.

No. 4
L12 HDPE Water Tanks (Ground & Roof): The work includes providing and installing a new 2,200
Liters effective storage capacity of UV-resistant HDPE vertical water tank, food grade with
top/open solid cover and solid body of FOUR/4 Layers (the TWO/Outer Layers for maintaining
water temperature/thermal resistance, middle Layer for sunlight protection/UV resistance
and inner layer for algae & odor protection), white color externally, Cooper/Brass embedded
inlet & outlet with an overflow of suitable size/site requirements, manufactured from 100%
virgin raw material not recycled (Polyethylene high density) with providing & installing float
valves of 3/4" size, approved quality & sample (Certificate of Origin & Quality should be
provided). The work also includes providing and installing all required Fittings and Valves,
which should be suitable for use with Polypropylene (PPR) Composite water pipes of min. 3
Layers of side walls. The work also includes providing materials and manpower to
manufacture a suitable steel base brace the water tank on the top roof by installing a rigid,
flat, and adequate size base on the existing concrete ground and roof by using a FLAT (NOT
CORRUGATED) Sandwich Panel (suitable quality & size) of 5 cm thickness & 25 Kg/Cu.M
density of core material under the bottom of HDPE water tanks, fixing/connecting the tank’s
body to the roof and masonry walls with tensile wire/chain with bolts, (excavation in different
locations & layers, backfilling, connection with existing main/feeding lines, concrete works
and all other necessary works). All work should be done according to the instructions of the
Supervisor Engineer.

Pcs 8
L13 Manholes and Covers :-
L13.1 Supply materials, construct and test Sewer Manholes size (40x40)cm and depth (≤100) cm,
Heavy GRP or Aheen ( Cast Iron) solid covers and strong frame according to the drawings.M.H
(40*40) cm and cover (40*40) cost includes excavation to the required depth and dimensions,
crushed stone, lean concrete, backfilling with approved soil materials, plain concrete 1:2:4
thickness 12 cm for the manhole base, walls with 20*20*40 cm hollow concrete blocks, cast
iron frame fixed in reinforced concrete slab. walls with cement-sand plastering ( 1:3 ) three
layers (smoothed surface) minimum thickness of 20 mm, then coating with three layers of
flint coat external and internal face, steel steps when required. The cast iron cover and frame
should be anti-rust painted and 3 layers of oil paint. All the works should be according to the
drawings and site engineer's instructions and according to section 1500 of I.G.T.S, IPC, IPSDC
and instructions of the site engineer.

No. 8
L13.2 Supply materials, construct and test plastic Manholes size (60x60)cm and depth (≤100) cm
for domestic water valves, heavy (plastic) solid GRP covers and strong frame according to
the drawings.M.H (60*60) cm and cover (60*60) the cost includes excavation to the required
depth and dimensions, crushed stone, lean concrete, backfilling with approved soil materials,

No. 4

15
 # Item Description Unit Quantity
L13.3 Supply materials, construct and test Sewer manholes size (80x80)cm and height (≤100) cm,
Aheen (Cast Iron) solid covers and strong frame according to the drawings. M.H (80*80) cm
and cover (DN60) the cost includes excavation to the required depth and dimensions, crushed
stone, lean concrete, backfilling with approved soil materials, plain concrete 1:2:4 thickness
15 cm for the manhole base, walls with 20*20*40 cm hollow concrete blocks, cast iron frame
fixed in the reinforced concrete slab. walls with cement sand plastering ( 1:3 ) three layers
(smoothed surface) with a minimum thickness of 20 mm, then coating with three layers of
flint coat external and internal face, steel steps when required. The cast iron cover and frame
should be anti-rust painted and 3 layers of oil paint. All the works should be according to the
drawings and site engineer and section 1500 of I.G.T.S, IPC, IPSDC and instructions of the site
engineer.

No. 8
L13.4 Supply materials, construct and test Sewer manholes size (100x100)cm and variable heights,
Aheen (Cast Iron) solid covers and strong frame according to the drawings. M.H (100*100) cm
and cover (DN60) the cost includes excavation to the required depth and dimensions, crushed
stone, lean concrete, backfilling with approved soil materials, plain concrete 1:2:4 thickness
15 cm for the manhole base, walls with 20*20*40 cm hollow concrete blocks, cast iron frame
fixed in the reinforced concrete slab. walls with cement sand plastering ( 1:3 ) three layers
(smoothed surface) with a minimum thickness of 20 mm, then coating with three layers of
flint coat external and internal face, steel steps when required. The cast iron cover and frame
should be anti-rust painted and 3 layers of oil paint. All the works should be according to the
drawings and site engineer and section 1500 of I.G.T.S, IPC, IPSDC and instructions of the site
engineer.

No. 6
L14 supply and install galvanized gutters: the work includes all excavation works, concrete
structure, fixing pipes outlets and solid cover,

L15 10x0.3x0.3 m No. 1

L16 5.6x0.1x0.1 m No. 1
L17 pit construction including all excavation work and backfilling with approved soil materials,
plain concrete 1:2:4 thickness 12 cm for the manhole base, walls with 20*20*40 cm hollow
concrete blocks

L17.1 8 m3 no. 1
L18 supply and install portable fire extinguishers 6 kg with all accessories, where they should be
installed on the wall (wall mounted ).
No. 9
L19 supply and install electrical board fire extinguishers 2 kg with all accessories, where they
should be installed on the wall (wall mounted ).
No. 7
L20 supply and install a Fire Extinguishing Ball with all accessories, over all electrical boards inside
the building According to the drawing.
No. 5
L21 Roof Treatment: Supply materials, equipment, and skilled labour required for coating the
roof using hyperdesmo weather and UV resistance polyurethane liquid membrane for
waterproofing & protection materials. Max service temperature 80 C down to -40 C. The price
includes Cleaning the surface using a high-pressure washer, laying a prime coat layer, and
applying the material with a roller or brush in two, at least, coats. Leave 6-24 hours between
coats. the price also includes coating the parapet 30cm high using the same materials.

M² 2000

16