Scribd
Upload
10 views2 pages

GCHNF Drillpipe Datasheet

The document provides detailed specifications for a 5-inch S-135 drillstring, including dimensions, weights, connection types, and tensile/torsional limits. It emphasizes the importance of confirming manufacturing specifications and handling equipment requirements. Additionally, it includes notes on make-up torques and the interchangeability of connections to ensure safe and effective use.

Uploaded by

ingrid.gmotta22
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
10 views2 pages

GCHNF Drillpipe Datasheet

The document provides detailed specifications for a 5-inch S-135 drillstring, including dimensions, weights, connection types, and tensile/torsional limits. It emphasizes the importance of confirming manufacturing specifications and handling equipment requirements. Additionally, it includes notes on make-up torques and the interchangeability of connections to ensure safe and effective use.

Uploaded by

ingrid.gmotta22
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Premium Drillstring Data Sheet

Pipe Size 5”, S-135, Range 2, (0.362” wall)


Weights Nominal 19.5 lbs/ft, Adjusted 22.6 lbs/ft
Connection Type API NC-50 (120ksi)
Hardbanding Various (Box only)
Internal Plastic Coating Tuboscope TK-34P

Generic String
Before use, confirm manufacture spec against NS-1 & last inspection was to NS-2

Basic Specifications
NEW PREMIUM (Min)
Tool Joint OD 6.625 in 6.3125 in
Tool Joint ID 3.25 in 3.25 in
Tube OD 5.0 in 4.855 in
Drift Diameter 3.125 in
Capacity 0.01703 bbls/ft These cap/disp figures are as
per manufacturer datasheet. For
Displacement (Closed End) 0.02559 bbls/ft critical jobs, local checks /
calculation are recommended.
Displacement (Open End) 0.00856 bbls/ft

Tensile / Torsional Limits


Tool Joint Tensile Yield 1,249,755 lbf 1,249,755 lbf
with 0.85 Safety Factor 1,062,290 lbf
Tool Joint Torsional Yield 51,710 ft.lbf 47,302 ft.lbf
with 0.85 Safety Factor 40,210 ft.lbf

Tube Tensile Yield 712,070 lbf 560,764 lbf


with 0.85 Safety Factor 476,650 lbf
Tube Torsional Yield 74,100 ft.lbf 58,110 ft.lbf
with 0.85 Safety Factor 49,400 ft.lbf

NOTE: The above max values can only be used when there is a single load case. For combined loads
(Torque & Tension), these values decrease thus reference "Combined Loading Charts" on page 3.

Handling Equipment
Elevators must be equipped with an 18° internal taper for lifting the box end tool joints.

Collapse Resistance
For consideration only during BOP Pressure Testing or when tension loads are negligible.
Tube may collapse if the externally applied pressure differential across the tube exceeds 10,024 psi.
(9,022 psi with Safety Factor of 0.90).

Page 1 Last Revised: Example for Reference Datasheet XXX Rev 00


For further assistance, contact: [email protected]
Premium Drillstring Data Sheet
Pipe Size 5”, S-135, Range 2, (0.362” wall)
Weights Nominal 19.5 lbs/ft, Adjusted 22.6 lbs/ft
Connection Type API NC-50 (120ksi)
Hardbanding Various (Box only)
Internal Plastic Coating Tuboscope TK-34P

Generic String

Make-up Torques
Make Make-up torque values given are calculated using the standard API formula taken from API
Recommended Practice 7G 16th Edition, 1998.

NEW Recommended* PREMIUM


XXX” XXX”
(8” OD) XXX” (Min OD)
DP Make up Torque (MUT) XXX ft.lbf XXX ft.lbf XXX ft.lbf XXX ft.lbf XXX ft.lbf

* The recommended make-up torque is based on a review of Delivery Ticket XYZ for drillpipe
dispatched to the XXX in XYZ, which found the minimum OD of the tooljoints to be XXX”.

Care is necessary if the drill pipe is being screwed onto another component (eg Crossover, HWDP,
Pup joint) to ensure that ID & OD dimensions are checked and material specification differences are
taken into account with the MUT.

Note on Interchangeability of Connections


q When considering running ‘interchangeable’ connection combinations it is essential to accurately
measure the two components prior to make-up. Ensure they are reworked in accordance with NS-
2™ and API Spec 7.
q If using mixed interchangeable connections, only apply the lower MUT value associated with the
API connection, as this will be the weaker component.

Page 2 Last Revised: Example for Reference Datasheet XXX Rev 00


For further assistance, contact: [email protected]

You might also like