Scribd
Upload
2 views

CISCO_BASIC_LAB_1738447540

The document outlines the configuration steps for a Cisco network setup, including IP address assignments for routers and switches, VLAN configurations, VTP mode settings, switchport trunk configurations, and OSPF routing configurations. It details commands for setting up routers (ISP, HO-1, HO-2) and switches (Core-SW1, Core-SW2, Access-SW1 to Access-SW4) with specific IP addresses, VLANs, and routing protocols. The steps ensure proper network segmentation and routing functionality within the defined network architecture.

Uploaded by

aarontamini01
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2 views

CISCO_BASIC_LAB_1738447540

The document outlines the configuration steps for a Cisco network setup, including IP address assignments for routers and switches, VLAN configurations, VTP mode settings, switchport trunk configurations, and OSPF routing configurations. It details commands for setting up routers (ISP, HO-1, HO-2) and switches (Core-SW1, Core-SW2, Access-SW1 to Access-SW4) with specific IP addresses, VLANs, and routing protocols. The steps ensure proper network segmentation and routing functionality within the defined network architecture.

Uploaded by

aarontamini01
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

CISCO LAB

Step 1: VLSM

STEP 2: Setting IP Address


For ISP Router:

Router(config)#hostname ISP

ISP(config)#int g0/0
ISP(config-if)#ip add 10.1.1.1 255.255.255.252
ISP(config-if)#no sh

ISP(config-if)#int g0/1
ISP(config-if)#ip add 10.1.2.1 255.255.255.252
ISP(config-if)#no sh

ISP(config-if)#int g0/2
ISP(config-if)#ip add 10.1.3.1 255.255.255.252
ISP(config-if)#no sh
ISP(config-if)#do wr

For HO-1 Rouer:

Router(config)#int g0/0
Router(config-if)#ip add 10.1.2.2 255.255.255.252
Router(config-if)#no sh

Router(config-if)#int g0/1
Router(config-if)#ip add 10.1.4.1 255.255.255.252
Router(config-if)#no sh

Router(config-if)#int g0/2
Router(config-if)#ip add 10.1.5.1 255.255.255.252
Router(config-if)#no sh

Router(config)#hostname HO-1

For HO-2 Router:

Router(config)#int g0/0
Router(config-if)#ip add 10.1.3.2 255.255.255.252
Router(config-if)#no sh

Router(config-if)#int g0/1
Router(config-if)#ip add 10.1.7.1 255.255.255.252
Router(config-if)#no sh
Router(config-if)#int g0/2
Router(config-if)#ip add 10.1.6.1 255.255.255.252
Router(config-if)#no sh

Router(config-if)#exit
Router(config)#hostname HO-2
HO-2(config)#do wr

For Core-SW1:

Switch(config)#hostname Core-SW1
Core-SW1(config)#int f0/1
Core-SW1(config-if)#ip add 10.1.4.2 255.255.255.252
^
% Invalid input detected at '^' marker.
Core-SW1(config-if)#no switchport

➔ Ai no switchport er maddome switching mode ke disable kora hoiche


switching mode disable na korle sei port e IP bosano jabe na.

Core-SW1(config-if)#ip add 10.1.4.2 255.255.255.252


Core-SW1(config-if)#no sh

➔ Akhane switch er khetre no sh na dileo hoi

Core-SW1(config-if)#int f0/6
Core-SW1(config-if)#no switchport

➔ Switch er sob golo port e Jodi ip bosanor proiojon hoi tahole sob portei
no switchport command diye switchport golo disable kore dite hobe.

Core-SW1(config-if)#ip add 10.1.6.2 255.255.255.252


Core-SW1(config-if)#no sh

Core-SW1(config-if)#do wr

For Core-SW2:

Switch(config)#hostname Core-SW2
Core-SW2(config)#int f0/1
Core-SW2(config-if)#no switchport
Core-SW2(config-if)#ip add 10.1.7.2 255.255.255.252
Core-SW2(config-if)#no sh

Core-SW2(config-if)#int f0/6
Core-SW2(config-if)#no switchport
Core-SW2(config-if)#ip add 10.1.5.2 255.255.255.252
Core-SW2(config-if)#no sh
Core-SW2(config-if)#do wr

STEP 3: VLAN CONFIGURATION


For Core-SW1

Core-SW1(config)#vlan 10
Core-SW1(config-vlan)#name Server

Core-SW1(config-vlan)#vlan 20
Core-SW1(config-vlan)#name IT

Core-SW1(config-vlan)#vlan 30
Core-SW1(config-vlan)#name HR

Core-SW1(config-vlan)#vlan 40
Core-SW1(config-vlan)#name ACC

Core-SW1(config-vlan)#vlan 50
Core-SW1(config-vlan)#name Sales
Core-SW1(config-vlan)#do wr

For Core-SW2:
Core-SW2(config)#vlan 10
Core-SW2(config-vlan)#name Server

Core-SW2(config-vlan)#vlan 20
Core-SW2(config-vlan)#name IT

Core-SW2(config-vlan)#vlan 30
Core-SW2(config-vlan)#name HR

Core-SW2(config-vlan)#vlan 40
Core-SW2(config-vlan)#name ACC

Core-SW2(config-vlan)#vlan 50
Core-SW2(config-vlan)#name Sales

Core-SW2(config-vlan)#do wr

STEP 4: VTP MODE CONFIGURATION


VTP Server for Core-SW1:
Core-SW1(config)#vtp mode s
Core-SW1(config)#vtp mode server
Device mode already VTP SERVER.

Core-SW1(config)#vtp domain itbd.tech


Changing VTP domain name from NULL to itbd.tech

Core-SW1(config)#vtp password itbd


Setting device VLAN database password to itbd
Core-SW1(config)#do wr

VTP Server for Core-SW2:


Core-SW2(config)#vtp mode server
Device mode already VTP SERVER.

Core-SW2(config)#vtp domain itbd.tech


Changing VTP domain name from NULL to itbd.tech

Core-SW2(config)#vtp password itbd


Setting device VLAN database password to itbd
Core-SW2(config)#do wr

VTP Client for Access-SW1:

Switch(config)#hostname Access-SW1
Access-SW1(config)#vtp mode client
Setting device to VTP CLIENT mode.

Access-SW1(config)#vtp domain itbd.tech


Changing VTP domain name from NULL to itbd.tech

Access-SW1(config)#vtp password itbd


Setting device VLAN database password to itbd
Access-SW1(config)#do wr

VTP Client for Access-SW2:

Switch(config)#hostname Access-SW2
Access-SW2(config)#vtp mode client
Setting device to VTP CLIENT mode.

Access-SW2(config)#vtp domain itbd.tech


Changing VTP domain name from NULL to itbd.tech
Access-SW2(config)#vtp password itbd
Setting device VLAN database password to itbd
Access-SW2(config)#do wr

VTP Client for Access-SW3:

Switch(config)#hostname Access-SW3
Access-SW3(config)#vtp mode client
Setting device to VTP CLIENT mode.

Access-SW3(config)#vtp domain itbd.tech


Changing VTP domain name from NULL to itbd.tech

Access-SW3(config)#vtp password itbd


Setting device VLAN database password to itbd
Access-SW3(config)#do wr

VTP Client for Access-SW3:

Switch(config)#hostname Access-SW4
Access-SW4(config)#vtp mode client
Setting device to VTP CLIENT mode.

Access-SW4(config)#vtp domain itbd.tech


Changing VTP domain name from NULL to itbd.tech

Access-SW4(config)#vtp password itbd


Setting device VLAN database password to itbd
Access-SW4(config)#do wr

STEP 5: SWITCHPORT TRUNK


For Core-SW1:

Core-SW1(config)#int range f0/2-5


Core-SW1(config-if-range)#switchport trunk encapsulation dot1q
Core-SW1(config-if-range)#switchport mode trunk

Core-SW1(config)#int range f0/7-10


Core-SW1(config-if-range)#switchport trunk encapsulation dot1q
Core-SW1(config-if-range)#switchport mode trunk

For Core-SW2:

Core-SW2(config)#int range f0/2-5


Core-SW2(config-if-range)#switchport trunk encapsulation dot1q
Core-SW2(config-if-range)#switchport mode trunk
Core-SW2(config-if-range)#exit
Core-SW2(config)#int range f0/7-10
Core-SW2(config-if-range)#switchport trunk encapsulation dot1q
Core-SW2(config-if-range)#switchport mode trunk

STEP 6: CONFIGURE ETHERCHANNEL


Core-SW1:

Core-SW1(config)#int range f0/2-5


Core-SW1(config-if-range)#channel-protocol pagp
Core-SW1(config-if-range)#channel-group 1 mode desirable

Core SW-2:

Core-SW2(config)#int range f0/2-5


Core-SW2(config-if-range)#channel-protocol pagp
Core-SW2(config-if-range)#channel-group 1 mode auto

STEP 7: CONFIGURE VLAN INTO ACCESS-SW INTERFACE


Access-SW1:

Access-SW1(config)#int range f0/3-5


Access-SW1(config-if-range)#switchport access vlan 10

Access-SW1(config-if-range)#int range f0/6-7


Access-SW1(config-if-range)#switchport access vlan 20
Access-SW1(config-if-range)#do wr

Access-SW2:

Access-SW2(config)#int range f0/3-4


Access-SW2(config-if-range)#switchport access vlan 30

Access-SW3:

Access-SW3(config)#int range f0/3-4


Access-SW3(config-if-range)#switchport access vlan 40
Access-SW3(config-if-range)#do wr

Access-SW4:

Access-SW4(config)#int range f0/3-4


Access-SW4(config-if-range)#switchport access vlan 50
Access-SW4(config-if-range)#do wr
STEP 8: SETTING IP INTO VLAN INTERFACE
Core-SW1:

Core-SW1(config-if)#int vlan 10
Core-SW1(config-if)#ip add 10.10.10.1 255.255.255.0

Core-SW1(config-if)#int vlan 20
Core-SW1(config-if)#ip add 20.20.20.1 255.255.255.0

Core-SW1(config-if)#int vlan 30
Core-SW1(config-if)#ip add 30.30.30.1 255.255.255.0

Core-SW1(config-if)#int vlan 40
Core-SW1(config-if)#ip add 40.40.40.1 255.255.255.0

Core-SW1(config-if)#int vlan 50
Core-SW1(config-if)#ip add 50.50.50.1 255.255.255.0
Core-SW1(config-if)#do wr

Core-SW2:

Core-SW2(config)#int vlan 10
Core-SW2(config-if)#ip add 10.10.10.2 255.255.255.0

Core-SW2(config-if)#int vlan 20
Core-SW2(config)#ip add 20.20.20.2 255.255.255.0

Core-SW2(config)#int vlan 20
Core-SW2(config-if)#ip add 20.20.20.2 255.255.255.0

Core-SW2(config-if)#int vlan 30
Core-SW2(config-if)#ip add 30.30.30.2 255.255.255.0

Core-SW2(config-if)#int vlan 40
Core-SW2(config-if)#ip add 40.40.40.2 255.255.255.0

Core-SW2(config-if)#int vlan 50
Core-SW2(config-if)#ip add 50.50.50.2 255.255.255.0
Core-SW2(config-if)#
Core-SW2(config-if)#do wr

STEP 9: OSPF ROUTING CONFIGURATION


For ISP Router:

ISP(config)#router ospf 1
ISP(config-router)#network 10.1.1.0 0.0.0.255 area 0
ISP(config-router)#network 10.1.2.0 0.0.0.3 area 0
ISP(config-router)#network 10.1.3.0 0.0.0.3 area 0

For HO-1 Router:

HO-1(config)#router ospf 1
HO-1(config-router)#network 10.1.2.0 0.0.0.3 area 0
HO-1(config-router)#network 10.1.4.0 0.0.0.3 area 0
HO-1(config-router)#network 10.1.5.0 0.0.0.3 area 0
HO-1(config-router)#do wr

For HO-2 Router:

HO-2(config)#router ospf 1
HO-2(config-router)#network 10.1.3.0 0.0.0.3 area 0
HO-2(config-router)#network 10.1.6.0 0.0.0.3 area 0
HO-2(config-router)#network 10.1.7.0 0.0.0.3 area 0
HO-2(config-router)#do wr

Core-SW1:

Core-SW1(config)#ip routing

→: Layer 3 switch er ketre routing korte chaile first e routing ta ip routing


command diye enable korte hoi , because layer 3 switch e routing default bhabe
disable thake

Core-SW1(config)#router ospf 1
Core-SW1(config-router)#network 10.1.4.0 0.0.0.3 area 0
Core-SW1(config-router)#network 10.1.6.0 0.0.0.3 area 0

Core-SW1(config-router)#network 10.10.10.0 0.0.0.255 area 0


Core-SW1(config-router)#network 20.20.20.0 0.0.0.255 area 0

Core-SW1(config-router)#network 30.30.30.0 0.0.0.255 area 0


Core-SW1(config-router)#network 30.30.30.0 0.0.0.255 area 0

Core-SW1(config-router)#network 40.40.40.0 0.0.0.255 area 0


Core-SW1(config-router)#network 50.50.50.0 0.0.0.255 area 0
Core-SW1(config-router)#do wr

Core-SW2:
Core-SW2(config)#ip routing

→: Layer 3 switch er ketre routing korte chaile first e routing ta ip routing


command diye enable korte hoi , because layer 3 switch e routing default bhabe
disable thake

Core-SW2(config)#router ospf 1
Core-SW2(config-router)#network 10.1.5.0 0.0.0.3 area 0
Core-SW2(config-router)#network 10.1.7.0 0.0.0.3 area 0

Core-SW2(config-router)#network 10.10.10.0 0.0.0.255 area 0


Core-SW2(config-router)#network 20.20.20.0 0.0.0.255 area 0

Core-SW2(config-router)#network 30.30.30.0 0.0.0.255 area 0


Core-SW2(config-router)#network 40.40.40.0 0.0.0.255 area 0

Core-SW2(config-router)#network 50.50.50.0 0.0.0.255 area 0


Core-SW2(config-router)#do wr

STEP 10: STP CONFIGURATION ALL CORE-SW


Core-SW1:

Core-SW1(config)#spanning-tree vlan 10,20,30 root primary


Core-SW1(config)#do wr

Core-SW1(config)#do sh spanning-tree

Core-SW2:

Core-SW2(config)#spanning-tree vlan 40,50 root primary


Core-SW2(config)#do wr

Step 11: HSRP CONFIGURATION


For Core-SW1:

Core-SW1(config)#interface Vlan10
Core-SW1(config-if)#standby 1 ip 10.10.10.254
Core-SW1(config-if)#standby 1 priority 200
Core-SW1(config-if)#standby 1 preempt

Core-SW1(config-if)#interface Vlan20
Core-SW1(config-if)#standby 1 ip 20.20.20.254
Core-SW1(config-if)#standby 1 priority 200

Core-SW1(config-if)#standby 1 preempt
Core-SW1(config-if)#interface Vlan 30
Core-SW1(config-if)#standby 1 ip 30.30.30.254
Core-SW1(config-if)#standby 1 priority 200
Core-SW1(config-if)#standby 1 preempt

Core-SW1(config-if)#interface Vlan 40
Core-SW1(config-if)#standby 1 ip 40.40.40.254
Core-SW1(config-if)#standby 1 preempt

Core-SW1(config-if)#interface Vlan 50
Core-SW1(config-if)#standby 1 ip 50.50.50.254
Core-SW1(config-if)#standby 1 preempt

For Core-SW2:

Core-SW2(config)#interface Vlan10
Core-SW2(config-if)#standby 1 ip 10.10.10.254
Core-SW2(config-if)#standby 1 preempt

Core-SW2(config-if)#interface Vlan20
Core-SW2(config-if)#standby 1 ip 20.20.20.254
Core-SW2(config-if)#standby 1 preempt

Core-SW2(config-if)#interface Vlan 30
Core-SW2(config-if)#standby 1 ip 30.30.30.254
Core-SW2(config-if)#standby 1 preempt

Core-SW2(config-if)#interface Vlan 40
Core-SW2(config-if)#standby 1 ip 40.40.40.254
Core-SW2(config-if)#standby 1 priority 200
Core-SW2(config-if)#standby 1 preempt

Core-SW2(config-if)#interface Vlan 50
Core-SW2(config-if)#standby 1 ip 50.50.50.254
Core-SW2(config-if)#standby 1 priority 200
Core-SW2(config-if)#standby 1 preempt

Step 12: DHCP Relay Agent configuration both Core-SW


Core-SW1:

Core-SW1(config)#int vlan 10
Core-SW1(config-if)#ip helper-address 10.10.10.20

Core-SW1(config-if)#int vlan 20
Core-SW1(config-if)#ip helper-address 10.10.10.20
Core-SW1(config-if)#int vlan 30
Core-SW1(config-if)#ip helper-address 10.10.10.20

Core-SW1(config-if)#int vlan 40
Core-SW1(config-if)#ip helper-address 10.10.10.20

Core-SW1(config-if)#int vlan 50
Core-SW1(config-if)#ip helper-address 10.10.10.20
Core-SW1(config-if)#do wr

Core-SW2:

Core-SW2(config)#int vlan 10
Core-SW2(config-if)#ip helper-address 10.10.10.20

Core-SW2(config-if)#int vlan 20
Core-SW2(config-if)#ip helper-address 10.10.10.20

Core-SW2(config-if)#int vlan 30
Core-SW2(config-if)#ip helper-address 10.10.10.20

Core-SW2(config-if)#int vlan 40
Core-SW2(config-if)#ip helper-address 10.10.10.20

Core-SW2(config-if)#int vlan 50
Core-SW2(config-if)#ip helper-address 10.10.10.20
Core-SW2(config-if)#do wr

STEP 12 DHCP SERVER CONFIGURATION


Router(config-if)#ip dhcp pool vlan-10
Router(dhcp-config)#network 10.10.10.254
Router(dhcp-config)#network 10.10.10.0 255.255.255.0
Router(dhcp-config)#default-router 10.10.10.254
Router(dhcp-config)#dns-server 1.1.1.1

Router(dhcp-config)#ip dhcp pool vlan-20


Router(dhcp-config)#network 20.20.20.0 255.255.255.0
Router(dhcp-config)#default-router 20.20.20.254
Router(dhcp-config)#dns-server 9.9.9.9

Router(dhcp-config)#ip dhcp pool vlan-30


Router(dhcp-config)#network 30.30.30.0 255.255.255.0
Router(dhcp-config)#default-router 30.30.30.254
Router(dhcp-config)#dns-server 8.8.8.8
Router(dhcp-config)#ip dhcp pool vlan-40
Router(dhcp-config)#network 40.40.40.0 255.255.255.0
Router(dhcp-config)#default-router 40.40.40.254
Router(dhcp-config)#dns-server 8.8.4.4

Router(dhcp-config)#ip dhcp pool vlan-50


Router(dhcp-config)#network 50.50.50.0 255.255.255.0
Router(dhcp-config)#default-router 50.50.50.254
Router(dhcp-config)#dns-server 8.8.8.8
Router(dhcp-config)#do wr

You might also like