Driving Follow Heart,Winning The Future

www.chinafolinn.com

H220 Series
Vector Control Frequency Inverter For Synchronous Motor

Manual
ZHEJIANG NEW FOLINN ELECTRIC CO.,LTD
Add: No. 9, 26th Street, Eastern New Area, Wenling, Zhejiang, China
Tel:+86-576-86421218
Fax:+86-576-86421168
http://www.chinafolinn.com
 Function & Parameter Table
The functional parameters of FS50L series inverters are grouping by function,total
15 groups from P0~PP.Each functional group includes several function codes.Function
codes adopt three-level menu, for example, “P5-03” means 3rd function code of the
functions in group P5.
For convenience of setting function codes,while operating with operation panel,
function group number corresponding first-level menu, function code number
corresponding second-level menu, and function cade parameters corresponding
third-level menu.
1. Contents note of function table is described as below:
First column “function code”: Functional parameter set and parametric number;
Second column “name”: Full name of functional parameters;
Third column “setting range”: Valid set value range of functional parameters;
Fourth column “factory default”: Original factory default of functional parameters;
Fifth column“modify” :Alteration property of functional parameters(whether or not
it is permitted to modify and modification conditions) and the explanations are described
as below:
“※”: it means the setting value of this parameter can be modified when inverter
is in stop or running state;
“●”: it means the setting value of this parameter cannot be modified when inverter
is in running state;
“**”: it means the numerical value of this parameter is practical detection record
value, and cannot be modified;
“##”: it means the numerical value of this parameter is“factory parameter”,and
is limited to be set by manufacturers.Users are prohibited about such
operation.
Sixth column“No.”:Serial number of this function code in the whole function
codes, as well as the store address in communication.
(Inverters have already made automatic inspection constraint about the modification
property of all parameters, which can help users to avoid faults in modification.）
2.“Factory default” refers to the numerical value after function code parameters are
renovated when you take factory reset operation; but the actually detective parameter
values or recorded values won’t be renovated.
3.To make more effective parameter protection, inverters provide password
protection for function codes. After users set password (the parameter of user password,
F07.00 set to non-0), and press PRGM/ESC to enter into user parameter editing state,
the system will enter into user password authorization state, and display “0.0.0.0.0.”.
The manipulator must input user password correctly,or he cannot get access to it.In the
unlocked state of password protection, user assword can be altered at any time,and user
password will be confirmed as the last input numerical value. When F07.00 is set to 0,
user password can be canceled; while power on, PP-00 set to non-0, then parameters
are protected by password.
4.While function code parameters are altered with serial communications,any
functions of user password still keep to above regulations.

-1-
 Function Description(setting range) Factory
Function & Parameter Table Name Change
code Default
0 : frequency A command
Function Factory 1 :frequency B command
Name Description(setting range) Change
code Default 2 : switch over between frequency A
Group P0 : Standard Function Parameters Frequency source command and frequency B command
P0-07 combination mode
0 ※
3 : A+B
0 :non-PG vector control ( SVC）
4 : A-B
P0-01 Speed control mode 1 :PG vector control（FVC） 0 ●
5 : MAX (A and B)
2 : V / F control
6:MIN (Aand B)
0:keypad control P0-08 Keypad setting frequency 0.00Hz～F00.03（m ax.frequency） 50.00Hz ※
P0-02 Command source selection 1:terminal control 0 ※ Model
P0-17 Acceleration time 1 0.00s～6500.0s dependent ※
2:RS 485 communication control
Model
P0-18 Deceleration time 1 0.00s～6500.0s dependent ※
P0-10 Max.output frequency 50.00Hz～600.00Hz 50.00Hz ●
0:1s
P0-12 Run frequency upper limit F00.05～F00.03 ( max.frequency ) 50.00Hz ※ Acceleration/Deceleration
P0-19 time unit 1:0.1 s 1 ●
0.00Hz～F00.04(run frequency upper
P0-14 Run frequency lower limit 00.00Hz ※ 2:0.01s
limit)

0:keypad, no retentive upon power 0:max.frequency（F00.03）

failure Acceleration/Deceleration
P0-25 time base frequency 1:setting frequency 0 ●
1:keypad, retentive upon power failure
2:100Hz
2:analog AI1
0: same direction
3:analog AI2 P0-09 Rotation direction 0 ※
1: reverse direction
Frequency A command 4:analog AI3
P0-03 selection
0 ● Model
5:pulse (HDI) P0-15 Carrier frequency 0.5kHz～16.0kHz ※
dependent
6:multi-speed running
Carrier frequency 0: No
7:simple PLC P0-16 adjustment with temperature 1:Yes 1 ※
8:PID control
9:RS485 Communication 0:set by F00.04
10:potentiometer 1: analog AI1

Frequency B command Source of frequency upper 2:analog AI2

P0-04 same as F00.06 0 ● P0-11 limit
0 ●
selection 3:analog AI3
Range of frequency B 0:relative to maximum frequency 4:pulse(HDI)
P0-05 command selection
0 ※
1:relative to frequency A command 5:RS485 communication

P0-13 Frequency upper limit offset 0.00Hz～max.frequency（F00.03） 00.00Hz ※

Base frequency for UP/
0: running frequency
P0-26 DOWN modification during 0 ●
1: set frequency
running

-2- -3-
Function Description(setting range) Factory Change
Name Function Factory
code Default Name Description(setting range) Change
Unit digit: (Binding keypad command code Default

to frequency source) Group P6: Start-stop Control Parameters

0: no binding 0:direct start
1 :keypad setting 1:rotational speed tracking restart
P6-00 Start mode
(valid on V/F control)
0 ※
2: analog AI1
2: pre-excited start
3: analog AI2
4: analog AI3 P6-03 Startup frequency 0.00Hz～10.00Hz 0.00Hz ※
5:pulse setting (HDI ) Startup frequency holding
P6-04 time
0.0s～100.0s 0.0s ●
6 :multi-speed run setting
7 :Simple PLC Startup DC braking current/
Binding command source to P6-05 Pre-excited current
0%～100% 0% ●
P0-27 frequency source 8: PID control 0000 ※
9: RS485 communication
Startup DC braking time/
Ten’s digit (Binding terminal command P6-06 0.0s～100.0s 0.0s ●
Pre-excited time
to frequency source)
Hundred's digit (Binding 0: line Acc/Dec time
Acceleration/ deceleration
communication command to frequency P6-07 mode
1:S curve Acc/Dec A 0 ●
source) 2:S curve Acc/Dec B
Thousands digit: (Binding Time proportion of S-curve
P6-08 start segment 0.0%～（100.0%-F01.07) 30.0% ●
auto-operation command to frequency
P6-09 Time proportion of S-curve 0.0%～（100.0%-F01.06) 30.0% ●
source) end segment
0: deceleration to stop
Frequency offset of frequency P6-10 Stop mode 0 ※
P0-21 0.00Hz～max.frequency P0-10 00.00Hz ※ 1:stop freely
B source during superposition
P6-15 Brake usage rate 0%～100% 100% ※
Retentive of keypad setting 0: no retentive
P0-23 0 ※
frequency upon power failure 1: retentive

0:no operation
1:restore factory defaults,not
PP-01 Function parameter restore 0 ●
include motor parameter
2: clear fault file

-4- -5-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Group P1: Motor Parameters 0:ABZ incremental encoder
P1-28 Encoder type 0 ●
Rated power of Model 1:UVW incremental encoder
P1-01 synchronous motor 1 0.1kW～1000.0kW dependent ●
Encoder pulses per
Rated frequency of Model P1-27 1～65535 2500 ●
P1-04 synchronous motor 1 0.01Hz～F00.03( max. frequency) dependent ● revolution

Rated speed of Model AB phase sequence of 0: forward

P1-05 synchronous motor 1 1rpm～65535rpm
dependent ● P1-32 0 ●
ABZ incremental encoder 1: reverse
Rated voltage of Model
P1-02 synchronous motor 1 1V～2000V dependent ●
P1-31 Encoder installation angle 0.0～359.9° 0.0° ●
0.01A～655.35A
UVW phase sequence of 0: forward
Rated current of ( inverter power< = 55kW) P1-30 0 ●
Model UVW encoder 1: reverse
P1-03 0.1A～6553.5A dependent ●
synchronous motor 1
( inverter power> 55kW) P1-33 UVW encoder angle offset 0.0～359.9° 0.0° ●

Encoder wire-break fault 0.0s: No action

0.001Ω～65.535Ω P1-36 detection time 0.1–10.0s 0.0 ●

Stator resistance of （inverter power < = 55kW）

Model 0: no self-learning
P1-16 0.0001Ω～6.5535Ω dependent ●
synchronous motor 1 1:dynamic self-learning of
Self-learning of motor
（inverter power> 55kW） P1-37 synchronous motor 0 ●
parameter
2:static self-learning of
synchronous motor
0.001Ω～65.535Ω
（inverter power < = 55kW）
Rotor resistance of Model
F02.07 0.0001Ω～6.5535Ω ●
synchronous motor 1 dependent
（inverter power> 55kW）

0.01mH～655.35mH
Function Description(setting range) Factory Change
Name
（inverter power < = 55kW） code Default
P1-17 Inductance of D shaft Model ●
0.001mH～65.535mH
dependent Group P2: Vector Control Parameters
（inverter power> 55kW） Proportional gain 1 of
P2-00 speed loop
1～100 30 ※
Integral time 1 of
0.1mH～6553.5mH P2-01 speed loop 0.01s～10.00s 0.50s ※
（inverter power < = 55kW） P2-02 Switch over low point frequency 0.00Hz～F03.05 5.00Hz ※
P1-18 Inductance of Q shaft Model ●
0.01mH～655.35mH
dependent P2-03 Proportional gain 2 of 1～100 20 ※
（inverter power> 55kW） speed loop
P2-04 Integral time 2 of 0.01s～10.00s 1.00s ※
speed loop
P2-05 Switch over high point frequency F03.02～F00.03(max.frequency) 10.00Hz ※
Back electromotive force of Model
P1-20 0.1V~6553.5V ● P2-06 Vector control slip gain 50 %～200 % 100% ※
synchronous motor dependent
P2-07 Speed loop output filter 0.000s～0.100s 0.000s ※
Vector control over
P2-08 excitation gain 0～200 64 ※

-6- -7-
 Function Description(setting range) Factory Change
Name
0:F03.10 code Default

1:analog AI1 Group P4: Input Terminals

2: analog AI2 P4-00 S1 terminal function selection 1 ●
3: analog AI3
P4-01 S2 terminal function selection 0 : no function 4 ●
4: Pulse（HDI）
Torque upper limit source 1:forward run
P2-09 in speed control mode 5:RS485 Communication 0 ※ P4-02 S3 terminal function selection 9 ●
2:reverse run
6:MIN(AI1,AI2)
P4-03 S4 terminal function selection 3:3-wire operation control 12 ●
7:MAX(AI1,AI2)
HDI terminal function 4:forward jog
( corresponding to F03.10
P4-04 13 ●
selection
5:reverse jog
digital setting) P4-05 S5 terminal function selection 0 ●
6:coast to stop
P4-06 S6 terminal function selection 7:fault reset 0 ●
Digital setting of torque upper 8:external fault normal
P2-10 limit in speed control mode 0.0%～200.0% 150.0% ※
open input
Excitation adjustment 9:UP command
P2-13 proportional gain 0～60000 2000 ※
Excitation adjustment 10:DOWN command
P2-14 integral gain 0～60000 1300 ※
11:clear UP/DOWN
Torque adjustment
P2-15 proportion gain 0～60000 2000 ※ （terminal、keypad）
Torque adjustment 12:multi-speed terminal 1
P2-16 integral gain 0～60000 1300 ※
13:multi-speed terminal 2
0: weak magnetic invalid 14:multi-speed terminal 3
P2-18 Weak magnetic mode 1:direct calculation mode 1 ※ 15:multi-speed terminal 4
2: automatically adjust 16:Pause operation
17:Acc/Dec time selection 1
P2-19 Depth of weak magnetic 0～50 5 ※
18:Acc/Dec time selection 2
Torque upper limit 0: invalid
P2-22 0 ※ 19:frequency source switch over
effect enable 1: valid
20:run command switch over
P2-23 Output voltage upper limit margin 0%～50% 5% ※ terminal
21:Acceleration/Deceleration
P2-24 The initial position angle 50%~180% 80% ※
detection current prohibited
22:PID pause
0: detection every time operation 23:PLC status reset
The initial position angle
P2-25 detection current
1: no detection 0 ※ 24:swing pause
2: detection when first time power on

-8- -9-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default

0 :valid on high level

25:terminal count
26:counter reset 1: valid on low level
27:length count input units' digit:S1
In put terminal
28:length reset P4-38 tens' digit:S2 00000 ●
valid mode selection 1
29:torque control prohibited hundreds' digit:S3
30:pulse input (enabled only for thousands' digit:S4
HDI) ten thousands' digit:S5
31:reserved
32:immediate DC braking
33:Normally closed (NC) input of 0 :valid on high level
external fault 1: valid on low level
34:frequency modification units' digit:S6
Input terminal polarity
forbidden P4-39 tens' digit:S7 00000 ●
35:reverse PID action direction selection 2
hundreds' digit:S8
36:external STOP terminal 1 thousands' digit:S9
37:command source switch over
ten thousands' digit:HDI
terminal 2
38:PID integral pause
P4-10 Filtering time of switch 0.000s～1.000s 0.010s ※
39:reserved
40:reserved
0 :2-wire control 1
41:motor selection terminal 1
Terminal control 1:2-wire control 2
42:reserved P4-11 0 ●
operation mode 2:3-wire control1
43:PID parameter switch over
44:reserved 3:3-wire control 2
45:reserved
46:speed / torque control P4-12 Terminal UP/DOWN rate 0.001Hz/s～65.535Hz/s 1.00Hz/s ※
switch over
47:emergency stop P4-35 S1 delay time 0.0s～3600.0s 0.0s ●
48:external stop terminal 2
49:deceleration DC braking P4-36 S2 delay time 0.0s～3600.0s 0.0s ●
50:clear the current running time
P4-37 S3 delay time 0.0s～3600.0s 0.0s ●
51: two-wire/ three wire switch
53：motor temperature protection P4-13 AI1 lower limit 0.00V～F05.20 0.00V ※
54：Solenoid valve output Corresponding setting of
P4-14 AI1 lower limit
-100.0%～+100.0% 0.0% ※
55：fan output
56：Enable phase sequence detection; P4-15 AI1 upper limit F05.18～+10.00V 10.00V ※
only S7 is valid Corresponding setting of
P4-16 AI1 upper limit -100.0%～+100.0% 100.0% ※
57：Fan overcurrent protection;
only S6 is valid P4-17 AI1 input filter time 0.00s～10.00s 0.10s ※

P4-18 AI2 low limit 0.00V～F05.25 0.00V ※

-10- -11-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Corresponding setting of
P4-19 -100.0%～+100.0% 0.0% ※ Group P5: Output Terminals
AI2 lower limit
P4-20 AI2 upper limit F05.23～+10.00V 10.00V ※ 0: Pulse output (HDOP)
P5-00 HDO terminal output mode 0 ※
Corresponding setting of 1: Switch signal output (HDOR)
P4-21 AI2 upper limit -100.0%～+100.0% 100.0% ※
P5-01 HDOR output selection 0:no output 0 ※
P4-22 AI2 input filter time 0.00s～10.00s 0.10s ※
Relay TA output selection 1:frequency reached
P4-23 AI3 lower limit -10.00V～F05.30 0.00V ※ P5-05 2 ※
（TA*TB*TC） 2:frequency-level detection
Corresponding setting of
P4-24 -100.0%～+100.0% 0 ※
AI3 lower limit Relay RA output selection FDT1 output
P4-25 AI3 upper limit F05.28～+10.00V 4.00V ※ P5-04 0 ※
（RA*RB*RC） 3:fault output (stop)
Corresponding setting of
P4-26 -100.0%～+100.0% 100.0% ※
AI3 upper limit P5-02 MO1 output selection 4:motor overload pre-warning 1 ※
P4-27 AI3 input filter time 0.00s～10.00s 0.10s ※ 5:inverter overload pre-warning

P4-28 HDI lower limit 0.00kHz～F05.35 0.00kHz ※ 6:zero-speed running (no output
Corresponding setting of at stop
P4-29 -100.0%～+100.0% 0.0% ※
HDI lower limit
7:zero-speed running 2 (no output
P4-30 HDI upper limit F05.33～+100.00kHz 50.00kHz ※
Corresponding setting of at stop
P4-31 HDI upper limit -100.0%～+100.0% 100.0% ※
8:frequency upper limit reached
P4-32 HDI frequency input filter time 0.00s～10.00s 0.10s ※
9:frequency lower limit reached
units' digit:AI curve selection (no output at stop)
1:curve 1(2 point,see F05.18～F05.21)
10:set count value reached
2:curve 2(2 point,see F05.23～F05.26)
3:curve 3(2 point,see F05.28～F05.31) 11:designated count value reached
4:curve 4(4 point,see F05.40～F05.47) 12:length reached
P4-33 AI curve selection 5:curve 5(4 point,see F05.48～F05.55) H.321 ※
13:PLC cycle complete
tens' digit::AI2 curve selection
hundreds' digit:AI3 curve selection 14:accumulative running time

reached

15:frequency limited

units' digit:(setting for AI1 less 16:torque limited

than minimum input) 17:ready for RUN
0:corresponding to the minimum input
18:inverter running
set
19:AI1>AI2
Setting for AI less than 1:0.0%
P4-34 minimum input H.000 ※ 20:undervoltage state output
tens' digit:(setting for AI2 less
than minimum input) 22:reserved
setting selection 23:reserved
hundreds' digit:(setting for AI3 less
24:accumulative power-on time
than minimum input)
reached

25:Frequency level detection

FDT2 output

-12- -13-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
P5-06 HDOP output selection 0 ※
26 :frequency 1 reached P5-07 AO1 output selection 0 : s etting frequency 0 ※
27: frequency 2 reached 1 :running frequency
P5-08 AO2 output selection 2 :output current 1 ※
28 :current 1 reached
3 :output voltage
29 :current 2 reached
4 :output speed
30 :timing reached 5 :output torque
31 : AI1 input limit exceeded 6 :output power

32 :load becoming 0 7 : Pulse input

（100 % corresponding to 100.0kHz）
33 :reverse running
8 : AI1
34 :zero current state
9 : AI2
35 :module temperature reached 10 : AI3
36 :output current limit exceeded 11 :lenth

37 :Frequency lower limit reached 12 :count value

13 :RS 485 communication
(having output at stop)
14 :output current
38 :Alarm output (keep running)
（100.0 % corresponding to 1000.0A）
39 :motor overheat warning 15 :output voltage
40 :current running time reached （100.0 % corresponding to 1000.0V)
16 :reserved

0: Positive logic
1: Negative logic P5-18 AO1 offset coefficient -100.0%～100.0% 0.0% ※
Output terminal Unit's digit:HDO
P5-22 0000 ※ P5-11 AO1 gain -10.00～+10.00 1.00 ※
valid mode selection Ten's digit:TA
Hundred's digit:RA P5-12 AO2 offset coefficient -100.0%～100.0% 0.0% ※
Thousand's digit:MO1 P5-13 AO2 gain -10.00～+10.00 1.00 ※

P5-17 HDO delay time 0.0s～3600.0s 0.0s ※

P5-21 TA delay time 0.0s～3600.0s 0.0s ※

P5-20 RA delay time 0.0s～3600.0s 0.0s ※

P5-18 MO1 output delay time 0.0s～3600.0s 0.0s ※

-14- -15-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Group P7: Keypad And Display
0000–FFFF
PP-00 User password 0～65535 0 ※ Bit00:length value
0: STOP/RST key enabled Bit01:PLC stage

STOP key function only in keypad control Bit02: pulse setting frequency(kHz)
P7.02 1: STOP/RST key enabled in 1 ※ Bit03:running frequency 2 (Hz)
selection
any operation mode Bit04:remaining running time
Bit05:AI1 voltage before correction (V)
0000–FFFF Bit06:AI2 voltage before correction (V)
Bit00: running frequency 1 (Hz) LED display running Bit07:AI3 voltage before correction (V)
P7-04 parameters 2 H.0000 ※
Bit01: set frequency (Hz) Bit08: linear speed
Bit02: output current (A) Bit09: current power-on time(Hour)
Bit03: output voltage (V) Bit10: current running time (Min)
Bit04: load speed display Bit11: pulse setting frequency(Hz)
Bit05: output power (kW) Bit12: Rs485 communication setting
Bit06: output torque (%) value
Bit07: bus voltage (V) Bit13: encoder feedback speed(Hz)
LED display running
P7-03 Bit08: PID setting H.008F ※ Bit14: main frequency A display(Hz)
parameters 1
Bit09: PID feedback value Bit15: auxiliary frequency B display (Hz)
Bit10: input terminal status
Bit11: output terminal status
Bit12: AI1 voltage (V) 0000–FFFF
Bit13: AI2 voltage (V) Bit00: set frequency (Hz)
Bit14: AI3 voltage (V) Bit01: bus voltage (V)
Bit15: count value Bit02: input terminal status
Bit03: output terminal status
Bit04: PID setting
Bit05: AI1 voltage (V)
P7-05 LED display stop parameters H.0063 ※
Bit06: AI2 voltage (V)
Bit07: AI3 voltage (V)
Bit08: Count value
Bit09: Length value
Bit10: PLC stage
Bit11: Load speed
Bit12: Pulse setting frequency (kHz)

-16- -17-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Load speed display Accumulative power-on time
P7-06 coefficient
0.0001～6.5000 1.0000 ※ P8-16 threshold
0h～65000h 0h ※
Accumulative running time
P8-17 threshold
0h～65000h 0h ※
Heatsink temperature of -
P7-07 inverter module
0.0℃～100.0℃ ** 0: No
P8-18 Startup protection
1: Yes
0 ※
P7-08 Software version - - **

P7-09 Accumulative running time0h～65535h - **

P8-15 Droop control 0.00Hz～10.00Hz 0.00Hz ※

- 0 ●
Frequency detection value
0: 0 decimal place P8-19 (FDT1)
0.00Hz～F00.03(max.frequency) 50.00Hz ※
Frequency detection
Number of decimal places 1: 1 decimal place P8-20 hysteresis (FDT hysteresis 1) 0.0%～100.0%（FDT1 level） 5.0% ※
P7-12 1 ※
for load speed display 2: 2 decimal places Frequency detection value
P8-28 0.00Hz～F00.03( max.frequency ) 50.00Hz ※
(FDT2)
3: 3 decimal places Frequency detection
P8-29 hysteresis (FDT hysteresis 2) 0.0%～100.0% ( FDT2 level ) 5.0% ※
P7-13 Accumulative power-on time 0h～65535h - ** Detection range of frequency
P8-21 0.0%～100.0%(F00.03(max.frequency)) 0.0% ※
Accumulative power - reached
P7-14 consumption 0–65535 kWh **
Jump frequency during 0: disabled
Group P8: Auxiliary Functions P8-22 acceleration/deceleration 1: enabled
0 ※
Model
P8-03 Acceleration time 2 0.0s～6500.0s dependent ※ Frequency switch over point
Model P8-25 between acceleration time 1 0.00Hz～F00.03( max.frequency ) 0.00Hz ※
P8-04 Deceleration time 2 0.0s～6500.0s dependent ※ and acceleration time 2
Model Frequency switch over point
P8-05 Acceleration time 3 0.0s～6500.0s dependent ※
P8-26 between deceleration time 1 0.00Hz～F00.03( max.frequency ) 0.00Hz ※
Model and deceleration time 2
P8-06 Deceleration time 3 0.0s～6500.0s dependent ※
Model 0: disabled
P8-07 Acceleration time 4 0.0s～6500.0s dependent ※ P8-27 Terminal JOG preferred
1: enabled
0 ※
Model
P8-08 Deceleration time 4 0.0s～6500.0s dependent ※ Any frequency reaching
P8-30 0.00Hz～F00.03( max.frequency ) 50.00Hz ※
detection value 1
P8-00 JOG running frequency 0.00Hz～F00.03(max.frequency) 2.00Hz ※ Any frequency reaching
P8-31 0.0%～100.0%(F00.03(max.frequency )) 0.0% ※
detection amplitude 1
P8-01 JOG acceleration time 0.0s～6500.0s 20.0s ※ Any frequency reaching
P8-32 0.00Hz～F00.03( max.frequency ) 50.00Hz ※
detection value 2
P8-02 JOG deceleration time 0.0s～6500.0s 20.0s ※ Any frequency reaching
P8-33 0.0%～100.0%(F00.03(max.frequency)) 0.0% ※
detection amplitude 2
P8-09 Jump frequency 1 0.00Hz～F00.03( max.frequency ) 0.00Hz ※
0.00Hz～F00.03( max.frequency )
P8-34 Zero current detection level 0.0%～300.0%(rated motor current) 5.0% ※
P8-10 Jump frequency 2 0.00Hz ※

P8-11 Frequency jump amplitude 0.00Hz～F00.03( max.frequency ) 0.00Hz ※ Zero current detection delay
P8-35 time
0.01s～600.00s 0.10s ※
Forward/Reverse rotation
P8-12 dead-zone time
0.0s～3000.0s 0.0s ※ 0.0% (no detection)
P8-36 Output overcurrent threshold 0.1%–300.0% (rated motor 200.0% ※
0: enabled current)
P8-13 Reverse control 0 ※
1: disabled
Output overcurrent detection
P8-37 delay time 0.00s～600.00s 0.00s ※
Running mode when set 0:run at frequency lower limit
P8-14 frequency lower than 1: stop 0 ※ P8-38 Any current reaching 1 0.0%～300.0%（(rated motor current） 100.0% ※
frequency lower limit 2: run at zero speed

-18- -19-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
P8-39 Any current reaching 1 0.0%～300.0%（rated motor current） 0.0% ※ Group P9: Fault and Protection
amplitude
P8-40 Any current reaching 2 0.0%～300.0%（rated motor current） 100.0% ※ 0: disabled
P9-12 Input phase loss protection 1 ※
Any current reaching 2 1: enabled
P8-41 amplitude 0.0%～300.0%（rated motor current） 0.0% ※
0: disabled
0: Disabled P9-13 Output phase loss protection 1 ※
P8-42 Timing function 1: Enabled 0 ※ 1: enabled

0: F08.45 Motor overload warning 0: disabled

P9-00 selection
1 ※
1: analog AI1 1: enabled
2: analog AI2 Motor overload pre-alarm
P8-43 Timing duration source 0 ※ P9-01 0.20～10.00 1.00 ※
warning detection levels
3: analog AI3 Motor overload pre-alarm
P9-02 50%～100% 80% ※
(100% of analog input corresponds warning detection time
to the value of F8.45) P9-09 Fault auto reset times 0～20 0 ※
P8-44 Timing duration 0.0Min～6500.0Min 0.0Min ※ P9-11 Time interval of fault auto 0.1s～100.0s 1.0s ※
reset
P8-45 AI1 input voltage lower limit 0.00V～F08.47 3.10V ※ P9-16 Current fault type - ●
P8-46 AI1 input voltage upper limit F08.46～10.00V 6.80V ※ 0: No fault
P9-15 2nd fault type - ●
Module temperature 1: Overcurrent during acceleration
P8-47 threshold 0℃～100℃ 75℃ ※ P9-14 1st fault type - ●
(E004)
0: Fan working during running 2: Overcurrent during deceleration
P8-48 Cooling fan control 0 ※
1: Fan working continuously (E005)
3: Overcurrent at constant speed
Dormant frequency (F8.52) to
P8-49 Wakeup frequency 0.00Hz ※ 4: Overvoltage during acceleration
maximum frequency (F00.03)
(E002)
P8-50 Wakeup delay time 0.0s～6500.0s 0.0s ※ 5: Overvoltage during deceleration
P8-51 Dormant frequency 0.00 Hz to wakeup frequency（F08.50） 0.00Hz ※ (E00A)
6: Overvoltage at constant speed
P8-52 Dormant delay time 0.0s～6500.0s 0.0s ※
(E003)
P8-53 Current running time reached 0.0Min～6500.0Min 0.0Min ※ 7: Undervoltage (E001)
8: Motor overload (E007)
9: inverter overload (E008)
10:Power input phase loss (E012)
11: Power output phase loss (E013)
12: Module overheat (E00E)
13:Buffer resistance overload (E014)

-20- -21-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
14: Contactor fault (E017) P9-29 Bus voltage upon 2nd fault - - ●
15: External equipment fault (E00d)
16: Communication fault(E018)
Input terminal status upon - -
17: Current detection fault (E015) P9-30 2nd fault ●
18: Motor auto-tuning fault (E016)
19: Running time reached (E020)
Output terminal status upon
20: EEPROM read-write fault (E00F)
P9-31 2nd fault
- - ●
21: Short circuit to ground (E023)
22: PID feedback lost during running
inverter status upon 2nd
(E02E) P9-32 fault
- - ●
23: Encoder/PG card fault(E026)
Power-on time upon 2nd
24: inverter hardware fault (E033) P9-33 fault
- - ●
25: Power-on time reached (E029)
26: Load becoming 0 (E030) P9-34 Running time upon 2nd fault - - ●
27: With-wave current limit fault (E032)
28: Too large speed deviation (E034)
P9-37 Frequency upon 1st fault - - ●
29: Motor switch over fault during
running (E038)
P9-38 Output current upon 1st fault - - ●
30: Motor over-speed (E035)
31: Motor overheat (E036)
P9-39 Bus voltage upon 1st fault - - ●
32: Initial position fault (E037)
33: phase sequence detection fault(E046)
Input terminal status upon
34: motor temperature protection(E047) P9-40 1st fault
- - ●
35: Maintenance time timeout fault(E048)
36: Exhaust temperature low temperature
protection(E049) Output terminal status upon
37: Fan phase loss protection(E050) P9-41 1st fault
- - ●
38: Fan overcurrent protection(E054)
inverter status upon 1st
39: Pressure greater than alarm value(E056)
P9-42 fault
- - ●
40: Exhaust temperature is higher than shutdown
alarm temperature of VFD(E057) Power-on time upon 1st
P9-43 fault
- - ●
41: Fan overload(E058)
42: Pressure sensor(E059)
P9-44 Running time upon 1st fault - - ●
43: Fan current detection fault (E070)
44 : There is current when the fan shutdown (E071)
Short-circuit to ground upon 0: Disabled
P9-07 power-on 1 ※
1: Enabled
P9-17 Frequency upon current fault - - ●
Output current upon current
- - Output terminal action during 0: Not act
P9-18 fault ● P9-10 fault auto reset 1: Act
0 ※
P9-19 Bus voltage upon current fault - - ● 0.0%~100.0%
Backup frequency upon
Input terminal status upon - - P9-55 abnormality
(100.0% corresponding to maximum 100.0% ※
P9-20 current fault ● frequency)F00.03)
Output terminal status upon
P9-21 current fault
- - ●
0: No temperature sensor
inverter status upon Type of motor temperature
P9-22 - - ● P9-56 sensor 1: PT100 0 ※
current fault
2: PT1000
Power-on time status upon
P9-23 current fault
- - ●
Motor overheat protection
Running time status upon P9-57 0℃～200℃ 110℃ ※
P9-24 current fault
- - ● threshold
Motor overheat warning
P9-58 0℃～200℃ 90℃ ※
P9-27 Frequency upon 2nd fault - - ● threshold

P9-28 Output current upon 2nd fault - - ● Action pause judging voltage
F09.04～100.0%
P9-62 at instantaneous power 90.0% ※
failure

-22- -23-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Group PA: Process Control PID Function PA-16 Integral time Ti2 0.01s～10.00s 2.00s ※

PA-17 Differential time Td2 0.000s～10.000s 0.000s ※

0: Keypad (F10.01)
1: Analog AI1 0: No switch over
2: Analog AI2 PID parameter switch over 1: Switch over via input terminal
PA-18 condition 2: Automatic switch over based on 0 ※
3: Analog AI3
PA-00 PID setting source 0 ※ deviation
4: Pulse setting (HDI)
5: Rs485 communication setting PID parameter switch over
PA-19 deviation 1 0.0%～F10.20 20.0% ※
6: Multi-speed command
PID parameter switch over
PA-20 deviation 2 F10.19～100.0% 80.0% ※

PA-21 PID initial value 0.0%～100.0% 0.0% ※

PA-01 PID digital setting 0.0～100.0% 50.0% ※
PA-22 PID initial value holding time 0.00～650.00s 0.00s ※
0: AI1 Maximum deviation between
PA- 23 two PID outputs in forward 0.00 %～100.00% 1.00% ※
1: AI2 direction
2: AI3
3: AI1 – AI2 Maximum deviation between
PA- 24 two PID outputs in reverse 0.00%～100.00% 1.00% ※
4: Pulse setting (HDI) direction
PA-02 PID feedback source 5: Rs485 communication setting 0 ※
6: AI1 + AI2 Unit's digit :Integral separated
7: MAX (|AI1|, |AI2|) 0: Invalid
8: MIN (|AI1|, |AI2|) 1: Valid
Ten's digit :Whether to stop
PA-25 PID integral property integral operation when the output 00 ※
reaches the limit
0：positive 0: Continue integral operation
PA-03 PID output characteristic 1：negative 0 ※
1: Stop integral operation

PA-04 PID setting feedback range 0～65535 1000 ※

Detection value of 0.0%: Not judging feedback loss
PA-05 Proportional gain Kp1 0.0～100.0 20.0 ※ PA-26 PID feedback loss 0.1%–100.0% 0.0% ※

PA-06 Integral time Ti1 0.01s～10.00s 2.00s ※ Detection time of

PA-27 PID feedback loss 0.0s～20.0s 0.0s ※
PA-07 Differential time Td1 0.000s～10.000s 0.000s ※
0: No PID operation at stop
Cut-off frequency of PID PA-28 PID operation at stop 0 ※
PA-08 0.00～F00.03(maximum frequency ) 2.00Hz ※ 1: PID operation at stop
reverse rotation

PA-09 PID deviation limit 0.0%～100.0% 0.0% ※

PA-10 PID differential limit 0.00%～100.00% 0.10% ※

PA-11 PID setting change time 0.00～650.00s 0.00s ※

PA-12 PID feedback filter time 0.00～60.00s 0.00s ※

PA-13 PID output filter time 0.00～60.00s 0.00s ※

PA-15 Proportional gain Kp2 0.0～100.0 20.0 ※

-24- -25-
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Group Pb: Swing Frequency, Fixed Length and Count PC-0 8 Multi-speed 8 - 100.0%～100.0% 0.0% ※

Swing frequency setting 0: Relative to the central frequency PC-09 Multi-speed 9 - 100.0%～100.0% 0.0% ※
Pb-00 mode 1: Relative to the maximum frequency 0 ※
PC- 10 Multi-speed 10 - 100.0%～100.0% 0.0% ※
Pb-01 Swing frequency amplitude 0.0%～100.0% 0.0% ※
PC- 11 Multi-speed 11 - 100.0%～100.0% 0.0% ※
Pb-02 Jump frequency amplitude 0.0%～50.0% 0.0% ※
PC- 12 Multi-speed 12 - 100.0%～100.0% 0.0% ※
Pb-03 Swing frequency cycle 0.1s～3000.0s 10.0s ※
PC- 13 Multi-speed 13 - 100.0%～100.0% 0.0% ※
Triangular wave rising time
Pb-04 coefficient 0.1%～100.0% 50.0% ※
PC- 14 Multi-speed 14 - 100.0%～100.0% 0.0% ※
Pb-05 Set length 0m～65535m 1000m ※
PC- 15 Multi-speed 15 - 100.0%～100.0% 0.0% ※
Pb-06 Actual length 0m～65535m 0m ※ Running time of simple PLC
PC- 18 multi-speed 0 0.0s(h)～6500.0s(h) 0.0s(h) ※
Pb-07 Number of pulses per meter 0.1～6553.5 100.0 ※
Acceleration/deceleration time
PC- 19 of simple PLC multi-speed 0 0～3 0 ※
Pb-08 Set count value 1～65535 1000 ※
Running time of simple PLC
Pb-09 Designated count value 1～65535 1000 ※ PC-20 multi-speed 1 0.0s(h)～6500.0s(h) 0.0s(h) ※

Group PC: Simple PLC Function And Multi-speed control Acceleration/deceleration time
PC- 21 of simple PLC multi-speed 1 0～3 0 ※
0: Stop after the inverter runs one cycle
1: Keep final values after the inverter
runs one cycle Running time of simple PLC
PC-16 Simple PLC running mode 0 ※ PC- 22 multi-speed 2 0.0s(h)～6500.0s(h) 0.0s(h) ※
2: Repeat after the inverter runs one
cycle
Acceleration/deceleration time
PC- 23 of simple PLC multi-speed 2 0～3 0 ※
Unit's digit :Retentive upon power
failure Running time of simple PLC
PC- 24 multi-speed 3 0.0s(h)～6500.0s(h) 0.0s(h) ※
0: No
Simple PLC retentive 1: Yes Acceleration/deceleration time
PC-17 selection 00 ※ PC- 25 of simple PLC multi-speed 3 0～3 0 ※
Ten's digit :Retentive upon stop
0: No
Running time of simple PLC
1: Yes PC- 26 multi-speed 4 0.0s(h)～6500.0s(h) 0.0s(h) ※

Acceleration/deceleration time
PC-00 Multi-speed 0 -100.0%～100.0% 0.0% ※
PC- 27 of simple PLC multi-speed 4 0～3 0 ※

PC-01 Multi-speed 1 -100.0%～100.0% 0.0% ※ Running time of simple PLC

PC- 28 multi-speed 5 0.0s(h)～6500.0s(h) 0.0s(h) ※
PC-02 Multi-speed 2 -100.0%～100.0% 0.0% ※ Acceleration/deceleration time
PC- 29 of simple PLC multi-speed 5 0～3 0 ※
PC-03 Multi-speed 3 -100.0%～100.0% 0.0% ※
Running time of simple PLC
PC- 30 0.0s(h)～6500.0s(h) 0.0s(h) ※
PC-0 4 Multi-speed 4 -100.0%～100.0% 0.0% ※ multi-speed 6

PC-05 Multi-speed 5 -100.0%～100.0% 0.0% ※

PC- 31
Acceleration/deceleration time
0～3 0 ※
of simple PLC multi-speed 6
PC-06 Multi-speed 6 -100.0%～100.0% 0.0% ※
Running time of simple PLC
PC- 32 multi-speed 7 0.0s(h)～6500.0s(h) 0.0s(h) ※
PC-07 Multi-speed 7 -100.0%～100.0% 0.0% ※

-26- -27
Function Description(setting range) Factory Change Function Description(setting range) Factory Change
Name Name
code Default code Default
Acceleration/deceleration time 0: Set by F12.02
PC-33 of simple PLC multi-speed 7 0～3 0 ※
1: AI1
Running time of simple PLC 2: AI2
PC- 34 multi-speed 8 0.0s(h)～6500.0s(h) 0.0s(h) ※
3: AI3
Acceleration/deceleration time PC-51 Multi-speed 0 source 4: Pulse setting 0 ※
PC- 35 of simple PLC multi-speed 8 0～3 0 ※
5: PID
Running time of simple PLC
PC- 36 0.0s(h)～6500.0s(h) 0.0s(h) ※ 6: Set frequency via keypad
multi-speed 9
(F00.10), modified UP/DOWN
Acceleration/deceleration time
PC- 37 of simple PLC multi-speed 9 0～3 0 ※

Running time of simple PLC Group Pd: Communication Parameters

PC- 38 multi-speed 10 0.0s(h)～6500.0s(h) 0.0s(h) ※
Pd-02 Local address 1～247，0 is broadcast address 1 ※
Acceleration/deceleration time
PC- 39 of simple PLC multi-speed 10 0～3 0 ※
0 : 300BPS
Running time of simple PLC
PC- 40 multi-speed 11 0.0s(h)～6500.0s(h) 0.0s(h) ※ 1: 600BPS
2: 1200BPS
Acceleration/deceleration time 3: 2400BPS
PC- 41 of simple PLC multi-speed 11 0～3 0 ※
4: 4800BPS
Running time of simple PLC Pd-00 Baud rate 5: 9600BPS 5 ※
PC- 42 multi-speed 12 0.0s(h)～6500.0s(h) 0.0s(h) ※
6: 19200BPS

Acceleration/deceleration time 7: 38400BPS

PC- 43 of simple PLC multi-speed 12 0～3 0 ※ 8: 57600BPS
9: 115200BPS
Running time of simple PLC 0.0s(h)～6500.0s(h)
PC- 44 multi-speed 13
0.0s(h) ※

Acceleration/deceleration time
PC- 45 of simple PLC multi-speed 13 0～3 0 ※
0: No check, data format (8,N,2)
Running time of simple PLC 1: Even parity check, data format (8,E,1)
PC- 46 multi-speed 14 0.0s(h)～6500.0s(h) 0.0s(h) ※
Pd-01 Data format 2: Odd Parity check, data format (8,O,1) 3 ※
FIXED
Acceleration/deceleration time 3: Data format (8,N,1)
PC- 47 of simple PLC multi-speed 14 0～3 0 ※

Running time of simple PLC Pd-03 Response delay 0ms～20ms 20 ※

PC- 48 multi-speed 15 0.0s(h)～6500.0s(h) 0.0s(h) ※

Acceleration/deceleration time
Pd-04 Communication timeout 0.0（invalid），0.1s～60.0s 0.0 ※
PC- 49 of simple PLC multi-speed 15 0～3 0 ※
0: Non-standard Modbus protocol
Pd-05 Modbus protocol selection 1: Standard Modbus protocol 1 ※
0: s (second)
PC- 50 Time unit of multi-speed 1:h (hour) 0 ※
Communication reading 0 : 0.01A
Pd-06 1: 0.1A
0 ※
current resolution

-28- -29-
 Fault Diagnosis and Trouble Shooting
Display Fault Name Possible Causes Solutions

7.1 Faults and Solutions

The BD600 provides a total of 34 pieces of fault information and protective functions. After 1.AC drive output circuit is 1.eliminate external faults
a fault occurs, the AC drive implements the protection function, and displays the fault code
ground or short circuit 2.self-learning of motor
on the operation panel (if the operation panel is available).
2.no self-learning of motor parameter
parameter 3.increase acceleration time
Before contacting for technical support, you can first determine the fault type,
3.acceleration time is too short 4.adjust manual torque boost
analyze the causes, and perform troubleshooting according to the following tables. If the
fault cannot be rectified, contact the agent or Folinn. Over-current 4.manual torque boost or V/F or V/F curve
E033 is the AC drive hardware overcurrent or overvoltage signal. In most situations, E004 during curve is not suitable 5.adjust to normal voltage
hardware overvoltage fault causes E033. acceleration 5.voltage is too low 6.speed tracking restart or
6.start rotating motor start after motor stop
7.additional load when 7.cancel additional load
Display Fault Name Possible Causes Solutions acceleration 8.select an AC drive of
8.AC drive type is too small higher power class
1. instantaneous power failure
2. input voltage of the inverter is
not within the specified 1. fault reset
requirements 2.adjust to normal voltage
3. bus voltage is abnormal 3.seek technical support
Bus
E001 4. rectifier bridge and buffer 4.seek technical support 1.AC drive output circuit is
under-voltage
resistance is abnormal 5.seek technical support ground or short circuit 1. eliminate external faults
5. drive board is abnormal 6.seek technical support 2.no self-learning of motor 2.self-learning of motor
6. main control board is parameter parameter
abnormal Over-current 3.deceleration time is too short 3.increase deceleration time
E005 during 4.voltage is too low 4. adjust to normal voltage
deceleration 5.additional load when 5.cancel additional load
1.input voltage is too high deceleration 6.install brake unit or brake
1. adjust to normal voltage 6.have no install brake unit or resistance
2.external force dragging
2.cancel external force or brake resistance
Over-voltage motor running in the process of
add a brake resistance
during acceleration
E002 3.increase acceleration time
acceleration 3.acceleration time is too short
4.install brake unit or brake
4.have no install brake unit or
resistance
brake resistance
1.AC drive output circuit is
1. eliminate external faults
ground or short circuit
2.self-learning of motor
2.no self-learning of motor
1.input voltage is too high parameter
Over-voltage 1.adjust to normal voltage Over-current parameter
2.external force dragging at constant 3. adjust to normal voltage
E003 at constant 2.cancel external force or E006 3.voltage is too low
motor running in the process speed running 4.cancel additional load
speed running add a brake resistance 4.additional load when
of running 5.select an AC drive of
running
higher power class.
5.AC drive type is too small

1.setting parameter correctly

1.Whether protection parameter
2.reduce the load and check the
F09.10 is suitable
Motor motor and mechanical
E007 2.Whether load is too heavy or
overload condition.
motor lock-rotor
3.select an AC drive of higher
3. AC drive type is too small
power class.

-30- -31-
Display Fault Name Possible Causes Solutions Display Fault Name Possible Causes Solutions

1.The load is too heavy or 1. reduce the load and check Current
1.the HALL device is faulty. 1.replace the faulty HALL device.
locked motor occurs on the the motor and mechanical E015 detection
2.the drive board is faulty. 2.replace the faulty drive board.
AC drive motor. condition. fault
E008
overload 2.The AC drive model is of too 2. select an AC drive of higher
1.set the motor parameters
small power class. power class. 1.the motor parameters are not
Motor according to the nameplate
set according to the nameplate.
E016 self-learning properly.
2.the motor self-learning times 2.check the cable connecting the
1.adjust the voltage to fault
1: The input voltage is too high. out. AC drive and the motor.
normal range.
2: An external force drives the 2.cancel the external force
motor during acceleration. 1.the drive board and power 1.replace the faulty drive board or
Overvoltage or install a braking resistor. power supply board.
3: The acceleration time is too Contactor supply are faulty.
E00A during 3.increase the acceleration E017 2.replace the faulty
short. fault 2.the contactor is faulty.
deceleration time. contactor.
4: The braking unit and braking 4.install the braking unit and
resistor are not installed. braking resistor. 1.the host computer is in 1.check the cabling of host
abnormal state. computer.
2.the communication cable is 2.check the communication
1.external fault signal is input Communication faulty. cabling.
External E018
via S. 1.reset the operation fault 3: F00.02 is set improperly. 3.set F00.02 correctly.
E00d equipment
2.external fault signal is input 2.reset the operation 4.the communication parameters 4.set the communication
fault
via virtual I/O. in group F13 are set improperly. parameters properly.

1.the ambient temperature is 1.lower the ambient

too high. temperature. Accumulative Clear the record through
The accumulative running time
2. the air filter is blocked. E020 running time the parameter initialization
2.clean the air filter. reached
reaches the setting value.
3.the fan is damaged. function.
Module 3.replace the damaged fan.
E00E 4. the thermally sensitive resistor 4.replace the damaged
overheat Short circuit The motor is short circuited to the
of the module is damaged. E023 Replace the cable or motor
thermally sensitive resistor. to ground ground.
5.the inverter module is
5.replace the inverter
damaged.
module. 1.set the encoder type
correctly based on the actual
EEPROM 1.the encoder type is incorrect.
Replace the main control situation.
E00F readwrite The EEPROM chip is damaged. 2.the cable connection of the
board. 2.eliminate external faults.
fault E026 Encoder fault encoder is incorrect.
3.replace the damaged
3.the encoder is damaged.
encoder.
4.the PG card is faulty.
1.the three-phase power input is 4.replace the faulty PG
1.eliminate external faults. card.
abnormal.
Power input 2.seek technical support
E012 2.the drive board is faulty.
phase loss 3.seek technical support
3.the lightening board is faulty. Accumulative Clear the record through the
4.seek technical support The accumulative power-on time
4.the main control board is faulty. E029 power-on time parameter initialization
reached
reaches the setting value.
function.

PID feedback Check the PID feedback

1.the cable connecting the AC The PID feedback is lower than
1.eliminate external faults. E02E lost during signal or set F10.26 to a
drive and the motor is faulty. the setting of F10.26.
2.check whether the motor running proper value.
2.the AC drive's three-phase
Power output three-phase winding is
outputs are unbalanced when
E013 phase loss normal.
the motor is running.
3.seek technical support Check that the load is
3.the drive board is faulty. Load The AC drive running current is
4.seek technical support E030 disconnected or the setting of
4.the module is faulty. becoming 0 lower than F09.13. F09.13 and F09.14 is correct.

-32- -33-
Display Fault Name Possible Causes Solutions Display Fault Name Possible Causes Solutions

1.reduce the load and check the 1.The temperature is too low 1.Motor head heating
1.the load is too heavy or locked motor and mechanical Exhaust tempe- 2.Temperature sensor fault
Pulse-by-pulse motor occurs on the motor. 2.Replace the temperature sensor
condition. rature low tem- 3.The temperature protection value is
E032 current limit 2.the AC drive model is too E049 3.Enlarged (a9-00)
perature too low
fault small power class.
2.select an AC drive of higher
power class.
1.Phase loss of heat dissipation motor 1.Replace the motor
2.Poor contact of fan motor wire 2.Reconnect
AC drive Fan phase
1.overvoltage exists. 1.handle based on overvoltage. 3.Detection board problem 3.Replace the detection board
E033 hardware E050 loss protection
2.overcurrent exists. 2.handle based on overcurrent. 4.The cooling motor is stuck 4.Find the cause and eliminate it
fault

1.the encoder parameters are set 1.set the encoder parameters Fan overcurr- The protection current value is Increase protection value
incorrectly. properly. E054 ent protection set too low (A9-28)
Too large 2.the motor self-learning is not 2.perform the motor
speed self-learning.
E034 performed.
deviation 3.set F09.17 and F09.60
3.F09.17 and F09.60 are set Pressure of The actual pressure of the air co- Check the the air compressor
correctly based on the actual
incorrectly. air compress- mpressor is too high,or the sensor pressure and the pressure
situation. E056
or is too high is inaccurate sensor and eliminate the fault

1.set the encoder parameters

1.the encoder parameters are set High exhaust Check the air compressor and
properly.
incorrectly. temperature Poor heat dissipation and oil check the ventilation and
2.perform the motor E057
Motor 2.the motor self-learning is not fault of air shortage of air compressor lubricating oil quantity
self-learning.
E035 over-speed performed. compressor
3.set F09.17 and F09.60
3.F09.17 and F09.60 are set
correctly based on the actual
incorrectly.
situation.
Air compreesor Excessive load, bearing wear and other Check the setting data,voltage,
E058 bearing, pipeline and other
fan is overload mechanical faults
Check that the motor mechanical faults
Initial
The motor parameters are not set parameters are set correctly
E037 position The sensor line is broken, the sensor is
based on the actual situation. and whether the setting of pressure sensor Check wiring and pressure
fault E059 broken, and the sensor is connected
rated current is too small. is not connected sensor
reversely

Motor
switch over Change the selection of the motor
Perform motor switch over Fan current Fan current detection problem change detection board, close
E038 fault during via terminal during running of the E070 the detection(P3-36=10)
AC drive.
after the AC drive stops. detection fault
running
There is current 1.Internal relay problem 1. Change control board
when fan shutd- 2.Fan current detection problem 2.Change detection board
phase sequence
The phase sequence of the power input
Check the air compressor circuit
E071 3.Setting value is too small
own 3. Increase the setting value
E046 detection fault
side of the air compressor is reversed,
and eliminate the fault
or the phase is lost (P3-50)

Motor 1.the temperature sensor cable

switch over 1. the cable of temperature sensor is loose and eliminate the fault
E047 fault during 2. motor temperature is to high 2. lower the carrier frequency or
running adopt other heat radition measures

Running time has reached maintenance

Maintenance Maintenance and cleaning time
E048 time timeout fault

-34- -35-
7.2 Common Faults and Solutions
SN Fault Possible Causes Solutions
You may come across the following faults during the use of the AC drive. Refer to the
following table for simple fault analysis. 1.check and reset the parameters
Table 7-1 Troubleshooting to common faults of the AC drive in group F05.
1.the parameters are set incorrectly.
2.the external signal is incorrect.
2.re-connect the external
SN Fault Possible Causes Solutions The S terminals 3.the jumper bar across DCM and signal cables.
7
are disabled. +24 V becomes loose. 3.re-confirm the jumper bar
1.there is no power supply to the
4.the control board is faulty. across DCM and +24 V.
AC drive or the power input to the
AC drive is too low. 4.seek technical support
2.the power supply of the switch on the
drive board of the AC drive is faulty. 1. check the power supply.
There is no
3.the rectifier bridge is damaged. 2. check the bus voltage. 1.the encoder is faulty.
1 display 4.the control board or the operation The motor speed 1.replace the encoder and ensure
3. re-connect the 34-core cables. 2.the encoder cable is connected
at power-on. panel is faulty. is always low in the cabling is proper.
4. seek technical support incorrectly or in poor contact.
5.the cable connecting the control 8 close loop vector 2.replace the PG card.
3.the PG card is faulty.
board and the drive board and the control mode. 4.the drive board is faulty. 3.seek technical support
operation panel breaks.

1.re-set motor parameters

1.the cable between the drive 1.the motor parameters are set
The AC drive
or re-perform the motor
board and the control board is in
improperly. self-learning.
poor contact. reports overcurrent
2.related components on the 9 and overvoltage 2.the acceleration/deceleration 2.set proper acceleration/
“bd600” is control board are damaged. frequently. time is improper. deceleration time.
1. re-connect the 34-core cables. 3.the load fluctuates.
2 displayed 3.the motor or the motor cable is 3.seek technical support
short circuited to the ground. 2. seek technical support
at power-on.
4.the HALL device is faulty.
5.the power input to the AC drive 1.check whether the contactor
is too low. cable is loose.
2.check whether the contactor
E017 is reported
1.the motor or the motor output 1.measure the insulation of The soft startup contactor is not is faulty.
10 upon power-on or
“E023” is picked up.
cable is short-circuited to the the motor and the output cable running. 3.heck whether 24 V power
3 displayed ground. with a megger.
at power-on.
supply of the contactor is faulty.
2.the AC drive is damaged. 2.seek technical support
4.seek technical support
The AC drive
display is normal
upon poweron.
1.the cooling fan is damaged or
88888 is displayed Related component on the control
But “bd600” is locked-rotor occurs. 1.replace the damaged fan. 11 upon power-on. board is damaged.
Replace the control board.
4 displayed after 2.the external control terminal 2.eliminate external fault.
running and stops cable is short circuited.
immediately.

1.the setting of carrier frequency is

too high. 1 . reduce the carrier frequency
E00E (module
2.the cooling fan is damaged, or the (F00.17).
overheat) fault air filter is blocked.
5 2.seplace the fan and clean the
is reported 3.components inside the AC drive
air filter.
frequently. are damaged (thermal coupler or
3.seek technical support
others).

1.check the motor and the motor 1.ensure the cable between the
cables. AC drive and the motor is
The motor does 2.the AC drive parameters are set
normal.
not rotate after improperly (motor parameters).
2.replace the motor or clear
6 the AC drive
3.the cable between the drive board
and the control board is in poor mechanical faults.
runs. contact. 3.check and re-set motor
4.the drive board is faulty. parameters.

-36- -37-