DESIGN CALCULATIONS

Ref Beam marked;- B1 Summery

Datas;-
Length of beam = 1700 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 170 mm Cover (d') = 40 mm
Provide depth = 400 mm Eff. Depth (d) = 360 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2 KN/m
Slab load = 10 KN/m Total load = 22 KN/m
Factored load = 33 KN/m
Point load 1 = 0 KN a = 1m b = 0.7 m
Point load 2 = 0 KN a = 1.55 m b = 0.15 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 11.92 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 147 mm
d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.2E+07 = -129978 Ast + 37.46 Ast2
Ast = 0.00 mm2
Ast(min) = 0.87xbxd/fy = 168 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 1.1 say 2

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 28.05 KN
2
Shear stress(Vv) = 0.35 N/mm
Pt = 100xAst/bxd
Pt = 0.43 %
For M20 and pt = 0.43 fiom table (26) IS 456-2000
Vc = 0.21 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 11250 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 290 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 400 2 y14 - 2y14 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- B2 Summery
Datas;-
Length of beam = 4000 mm Width of beam = 200 mm
2
fy = 415 N/mm fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 400 mm Cover (d') = 40 mm
Provide depth = 500 mm Eff. Depth (d) = 460 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2.5 KN/m
Slab load = 14 KN/m Total load = 26.5 KN/m
Factored load = 39.75 KN/m
Point load 1 = 0 KN a = 0m b = 0m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 79.5 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 380 mm
d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
8E+07 = -166083 Ast + 37.46 Ast2
Ast = 545.89 Sq.mm
Ast(min) = 0.87xbxd/fy = 210 Sq.mm

Find Number of bars;-

Assume dia of bars, = 14 mm 3.5 say 4
Provide 2 y 14 = 308 2 y 14 = 308
= 615 Ast provided ok

Compression Reinforcement;-
2 y 14 = 308 Ast provided ok

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 79.5 KN
Shear stress(Vv) = 0.80 N/Sq.mm
Pt = 100xAst/bxd Pt = 0.67 %
For M20 and pt = 0.67 fiom table (26) IS 456-2000
Vc = 0.35 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 44500 N
Providing 8 mm ф bars Asv = 100.48 Sq.mm
 Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 227 mm
Provide 8 mm ф bars@ 180 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 500 2 y14 2y14 2y14 - y8 @ 18 cmc/c
125186.34
40896.656
 DESIGN CALCULATIONS
Ref Beam marked;- B3 Summery
Datas;-
Length of beam = 4600 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 460 mm Cover (d') = 40 mm
Provide depth = 600 mm Eff. Depth (d) = 560 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3 KN/m
Slab load = 14 KN/m Total load = 27 KN/m
Factored load = 40.5 KN/m
Point load 1 = 0 KN a = 2.5 m b = 2.1 m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 107.12 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 441 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.1E+08 = -202188 Ast + 37.46 Ast2
Ast = 595.52 Sq.mm
Ast(min) = 0.87xbxd/fy = 252 Sq.mm
Find Number of bars;-
Assume dia of bars, = 16 mm 3.0 say 4
Provide 2 y 16 = 402 2 y 16 = 402
= 804 Ast provided ok
Compression Reinforcement;-
2 y 14 = 308 Ast provided ok
Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 93.15 KN
Shear stress(Vv) = 0.78 N/Sq.mm
Pt = 100xAst/bxd Pt = 0.72 %
For M20 and pt = 0.72 fiom table (26) IS 456-2000
Vc = 0.35 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 51150 N
Providing 8 mm ф bars Asv = 100.48 Sq.mm
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 186 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 600 2 y16 2y16 2y16 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- B3 Summery
Datas;-
Length of beam = 4900 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 490 mm Cover (d') = 40 mm
Provide depth = 600 mm Eff. Depth (d) = 560 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3 KN/m
Slab load = 14 KN/m Total load = 27 KN/m
Factored load = 40.5 KN/m
Point load 1 = 0 KN a = 2.5 m b = 2.4 m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 121.55 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 469 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.2E+08 = -202188 Ast + 37.46 Ast2
Ast = 689.17 Sq.mm
 Ast(min) = 0.87xbxd/fy = 252 Sq.mm

Find Number of bars;-

Assume dia of bars, = 16 mm 3.4 say 4
Provide 2 y 16 = 402 2 y 16 = 402
= 804 Ast provided ok

Compression Reinforcement;-
2 y 14 = 308 Ast provided ok

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 99.23 KN
Shear stress(Vv) = 0.83 N/Sq.mm
Pt = 100xAst/bxd Pt = 0.72 %
For M20 and pt = 0.72 fiom table (26) IS 456-2000
Vc = 0.35 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 57225 N
Providing 8 mm ф bars Asv = 100.48 Sq.mm
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 186 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 600 2 y16 2y16 2y16 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- B5 Summery
Datas;-
Length of beam = 5600 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 560 mm Cover (d') = 40 mm
Provide depth = 600 mm Eff. Depth (d) = 560 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3 KN/m
Slab load = 15 KN/m Total load = 28 KN/m
Factored load = 42 KN/m
Point load 1 = 0 KN a = 1.3 m b = 4.3 m
Point load 2 = 0 KN a = 1.5 m b = 4.1 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 164.64 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 546 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.6E+08 = -202188 Ast + 37.46 Ast2
Ast = 0.00 Sq.mm
Ast(min) = 0.87xbxd/fy = 252 Sq.mm

Find Number of bars;-

Assume dia of bars, = 16 mm 0.0 say 4
Provide 3 y 16 = 603 2 y 16 = 402
= 1005 Ast provided ok

Compression Reinforcement;-
2 y 16 = 402 Ast provided ok

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 117.6 KN
Shear stress(Vv) = 0.98 N/Sq.mm
Pt = 100xAst/bxd Pt = 0.72 %
 For M20 and pt = 0.72 fiom table (26) IS 456-2000
Vc = 0.35 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 75600 N
Providing 8 mm ф bars Asv = 100.48 Sq.mm
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 186 mm
Provide 8 mm ф bars@ 150 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 600 3 y16 2y16 2y16 - y8 @ 15 cmc/c
 BEAM DESIGN
Name the beam B6
Refer: Calculations Results
Analysis of beam:-
Span = 5.6 m Width = 200 mm
Depth = 600 mm Beam B6
b= 200 mm
Loadings:- D= 600 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 3 Y- 16
Total load = 27 kn/m Beam Factored = 40.5 kn/m B.curt 2 Y- 14
Point Loa = 0 kn 1.5 m from left Top 2 Y- 16
Point Loa = 0 kn 3 m from left T.o.c.s 2 Y- 18
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 180
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 180
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 126 kn-m

Design:-
Span = 5.6 m
B.S.8110 Max Positive Moment Mu = 126.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 145 Kn.m
Max Shear force V = 117.4 Kn
Width of beam b = 200 mm
Effective depth of beam d = 562 mm 600 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.100 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.873 d mm
leverarm limited to 0.95d
Then , Z = 0.873 d mm = 491 mm
 Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 711.23769 sq.mm
Provide 3 16 mmdia
2 14 mmdia
Area of tension reinf pro: 910.6 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 562 mm
K=M/(bd^2fcu) 0.115
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.850 d mm
Z = 0.850 d mm = 478 mm
As = 840.74275 sq.mm
Provide top 2 16 mmdia
2 18 mmdia
Area of top reinf: provided = 910.6 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.810
T3.9P3/11 Design shear stress, vc = 0.589 N/sq.mm 1
Actual shear stress,v=V/b/d 1.044 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 398.37403 mmor.75*d 421.5
Provide st-s 8 mmdia @ 180 mm,c/c
Provide st-m 8 mmdia @ 180 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B7
Refer: Calculations Results
Analysis of beam:-
Span = 2.2 m Width = 200 mm
Depth = 600 mm Beam B7
b= 200 mm
Loadings:- D= 600 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 2 Y- 16
Total load = 27 kn/m Factored = 40.5 kn/m B.curt 0 Y- 0
Point Loa = 0 kn 1.5 m from left Top 2 Y- 16
Point Loa = 0 kn 3 m from left T.o.c.s 2 Y- 18
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 78 kn-m

Design:-
Span = 2.2 m
B.S.8110 Max Positive Moment Mu = 45.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 145.00 Kn.m
Max Shear force V = 117.4 Kn
Effective depth of beam d = 562 mm 600 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.115 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.850 d mm
leverarm limited to 0.95d
Then , Z = 0.850 d mm = 478 mm

Area of tension reinforcement.

 As=M*10^6/0.87/fy/Z 260.92016 sq.mm
Provide 2 16 mmdia
0 0 mmdia
Area of tension reinf pro: 401.92 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 562 mm
K=M/(bd^2fcu) 0.115
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.850 d mm
Z = 0.850 d mm = 478 mm
As = 840.74275 sq.mm
Provide top 2 16 mmdia
2 18 mmdia
Area of top reinf: provided = 910.6 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.358
T3.9P3/11 Design shear stress, vc = 0.449 N/sq.mm 1
Actual shear stress,v=V/b/d 1.044 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 304.39221 mmor.75*d 421.5
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 DESIGN CALCULATIONS
Ref Beam marked;- B8 Summery
Datas;-
Length of beam = 5200 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 520 mm Cover (d') = 40 mm
Provide depth = 700 mm Eff. Depth (d) = 660 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3.5 KN/m
Slab load = 20 KN/m Total load = 33.5 KN/m
Factored load = 50.25 KN/m
Point load 1 = 0 KN a = 1.3 m b = 3.9 m
Point load 2 = 0 KN a = 1.5 m b = 3.7 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 170 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 170 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 555 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.7E+08 = -238293 Ast + 37.46 Ast2
Ast = 0.00 Sq.mm
Ast(min) = 0.87xbxd/fy = 293 Sq.mm

Find Number of bars;-

Assume dia of bars, = 16 mm 0.0 say 4
Provide 3 y 16 = 603 2 y 16 = 402
= 1005 Ast provided ok

Compression Reinforcement;-
2 y 16 = 402 Ast provided ok

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 130.7 KN
Shear stress(Vv) = 0.93 N/Sq.mm
Pt = 100xAst/bxd Pt = 0.61 %
 For M20 and pt = 0.61 fiom table (26) IS 456-2000
Vc = 0.35 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 81650 N
Providing 8 mm ф bars Asv = 100.48 Sq.mm
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 158 mm
Provide 8 mm ф bars@ 150 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 700 3 y16 2y16 2y16 - y8 @ 15 cmc/c
 BEAM DESIGN
Name the beam B9
Refer: Calculations Results
Analysis of beam:-
Span = 5.6 m Width = 200 mm
Depth = 700 mm Beam B9
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 2 Y- 18
Total load = 27 kn/m Beam Factored = 40.5 kn/m B.curt 2 Y- 18
Point Loa = 0 kn 1.5 m from left Top 2 Y- 18
Point Loa = 0 kn 3 m from left T.o.c.s 2 Y- 18
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 175 kn-m

Design:-
Span = 5.6 m
B.S.8110 Max Positive Moment Mu = 175.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 179 Kn.m
Max Shear force V = 117.4 Kn
Width of beam b = 200 mm
Effective depth of beam d = 661 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.100 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.872 d mm
leverarm limited to 0.95d
Then , Z = 0.872 d mm = 577 mm
 Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 840.45325 sq.mm
Provide 2 18 mmdia
2 18 mmdia
Area of tension reinf pro: 1017.36 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 661 mm
K=M/(bd^2fcu) 0.102
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.869 d mm
Z = 0.869 d mm = 574 mm
As = 863.05602 sq.mm
Provide top 2 18 mmdia
2 18 mmdia
Area of top reinf: provided = 1017.36 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.770
T3.9P3/11 Design shear stress, vc = 0.579 N/sq.mm 1
Actual shear stress,v=V/b/d 0.888 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 587.22003 mmor.75*d 495.75
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B10
Refer: Calculations Results
Analysis of beam:-
Span = 2.2 m Width = 200 mm
Depth = 700 mm Beam B10
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 2 Y- 18
Total load = 27 kn/m Factored = 40.5 kn/m B.curt 0 Y- 0
Point Loa = 0 kn 1.5 m from left Top 2 Y- 18
Point Loa = 0 kn 3 m from left T.o.c.s 2 Y- 18
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 78 kn-m

Design:-
Span = 2.2 m
B.S.8110 Max Positive Moment Mu = 34.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 179.00 Kn.m
Max Shear force V = 117.4 Kn
Effective depth of beam d = 661 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.102 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.869 d mm
leverarm limited to 0.95d
Then , Z = 0.869 d mm = 574 mm

Area of tension reinforcement.

 As=M*10^6/0.87/fy/Z 163.93243 sq.mm
Provide 2 18 mmdia
0 0 mmdia
Area of tension reinf pro: 508.68 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 661 mm
K=M/(bd^2fcu) 0.102
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.869 d mm
Z = 0.869 d mm = 574 mm
As = 863.05602 sq.mm
Provide top 2 18 mmdia
2 18 mmdia
Area of top reinf: provided = 1017.36 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.385
T3.9P3/11 Design shear stress, vc = 0.460 N/sq.mm 1
Actual shear stress,v=V/b/d 0.888 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 423.43699 mmor.75*d 495.75
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B11
Refer: Calculations Results
Analysis of beam:-
Span = 5.2 m Width = 200 mm
Depth = 700 mm Beam B11
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13.5 kn/m From slab = 13.5 kn/m Bott-st 3 Y- 18
Total load = 27 kn/m Factored = 40.5 kn/m B.curt 2 Y- 20
Point Loa = 0 kn 2 m from left Top 2 Y- 18
Point Loa = 0 kn 0 m from left T.o.c.s 0 Y- 0
Reaction at left 105.3 kn Stir:(1) 8 Y,@ 150
Reaction at right 105.3 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 2.60 m F.b 0 nos 0
Maximum span moment = 137 kn-m

Design:-
Span = 5.2 m
B.S.8110 Max Positive Moment Mu = 260 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 0 Kn.m
Max Shear force V = 105.3 Kn
Width of beam b = 200 mm
Effective depth of beam d = 661 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.149 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.791 d mm
leverarm limited to 0.95d
Then , Z = 0.791 d mm = 523 mm
 Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 1377.236 sq.mm
Provide 3 18 mmdia
2 20 mmdia
Area of tension reinf pro: 1391.02 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 661 mm
K=M/(bd^2fcu) 0.000
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 1.000 d mm
Z = 0.950 d mm = 628 mm
As = 0 sq.mm
Provide top 2 18 mmdia
0 0 mmdia
Area of top reinf: provided = 508.68 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 1.052
T3.9P3/11 Design shear stress, vc = 0.643 N/sq.mm 1
Actual shear stress,v=V/b/d 0.797 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 1180.106 mmor.75*d 495.75
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B12
Refer: Calculations Results
Analysis of beam:-
Span = 5.6 m Width = 200 mm
Depth = 700 mm Beam B12
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 2 Y- 20
Total load = 27 kn/m Beam Factored = 40.5 kn/m B.curt 2 Y- 18
Point Loa = 0 kn 1.5 m from left Top 2 Y- 20
Point Loa = 0 kn 3 m from left T.o.c.s 2 Y- 20
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 215 kn-m

Design:-
Span = 5.6 m
B.S.8110 Max Positive Moment Mu = 215.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 240 Kn.m
Max Shear force V = 117.4 Kn
Width of beam b = 200 mm
Effective depth of beam d = 660 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.123 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.836 d mm
leverarm limited to 0.95d
Then , Z = 0.836 d mm = 552 mm
 Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 1079.2459 sq.mm
Provide 2 20 mmdia
2 18 mmdia
Area of tension reinf pro: 1136.68 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 660 mm
K=M/(bd^2fcu) 0.138
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.811 d mm
Z = 0.811 d mm = 536 mm
As = 1241.3045 sq.mm
Provide top 2 20 mmdia
2 20 mmdia
Area of top reinf: provided = 1256 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.861
T3.9P3/11 Design shear stress, vc = 0.601 N/sq.mm 1
Actual shear stress,v=V/b/d 0.889 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 629.54634 mmor.75*d 495
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B13
Refer: Calculations Results
Analysis of beam:-
Span = 2.2 m Width = 200 mm
Depth = 700 mm Beam B13
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 2 Y- 20
Total load = 27 kn/m Factored = 40.5 kn/m B.curt 0 Y- 0
Point Loa = 0 kn 1.5 m from left Top 2 Y- 20
Point Loa = 0 kn 3 m from left T.o.c.s 2 Y- 20
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 78 kn-m

Design:-
Span = 2.2 m
B.S.8110 Max Positive Moment Mu = 46.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 240.00 Kn.m
Max Shear force V = 117.4 Kn
Effective depth of beam d = 660 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.138 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.811 d mm
leverarm limited to 0.95d
Then , Z = 0.811 d mm = 536 mm

Area of tension reinforcement.

 As=M*10^6/0.87/fy/Z 237.9167 sq.mm
Provide 2 20 mmdia
0 0 mmdia
Area of tension reinf pro: 628 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 660 mm
K=M/(bd^2fcu) 0.138
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.811 d mm
Z = 0.811 d mm = 536 mm
As = 1241.3045 sq.mm
Provide top 2 20 mmdia
2 20 mmdia
Area of top reinf: provided = 1256 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.476
T3.9P3/11 Design shear stress, vc = 0.493 N/sq.mm 1
Actual shear stress,v=V/b/d 0.889 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 458.0286 mmor.75*d 495
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B14
Refer: Calculations Results
Analysis of beam:-
Span = 5.6 m Width = 200 mm
Depth = 700 mm Beam B14
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 4 Y- 20
Total load = 27 kn/m Beam Factored = 40.5 kn/m B.curt 2 Y- 20
Point Loa = 0 kn 1.5 m from left Top 2 Y- 20
Point Loa = 0 kn 3 m from left T.o.c.s 4 Y- 20
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 304 kn-m

Design:-
Span = 5.6 m
B.S.8110 Max Positive Moment Mu = 304.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 307 Kn.m
Max Shear force V = 117.4 Kn
Width of beam b = 200 mm
Effective depth of beam d = 660 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.174 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.737 d mm
leverarm limited to 0.95d
Then , Z = 0.737 d mm = 486 mm
 Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 1731.1237 sq.mm
Provide 4 20 mmdia
2 20 mmdia
Area of tension reinf pro: 1884 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 660 mm
K=M/(bd^2fcu) 0.176
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.733 d mm
Z = 0.733 d mm = 484 mm
As = 1757.9205 sq.mm
Provide top 2 20 mmdia
4 20 mmdia
Area of top reinf: provided = 1884 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 1.427
T3.9P3/11 Design shear stress, vc = 0.712 N/sq.mm 1
Actual shear stress,v=V/b/d 0.889 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 1020.023 mmor.75*d 495
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B15
Refer: Calculations Results
Analysis of beam:-
Span = 2.2 m Width = 200 mm
Depth = 700 mm Beam B15
b= 200 mm
Loadings:- D= 700 mm
Block&beams 13 kn/m From slab = 14 kn/m Bott-st 2 Y- 20
Total load = 27 kn/m Factored = 40.5 kn/m B.curt 0 Y- 0
Point Loa = 0 kn 1.5 m from left Top 2 Y- 20
Point Loa = 0 kn 3 m from left T.o.c.s 4 Y- 20
Reaction at left 77.0 kn Stir:(1) 8 Y,@ 150
Reaction at right 117.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 1.90 m F.b 0 nos 0
Maximum span moment = 78 kn-m

Design:-
Span = 2.2 m
B.S.8110 Max Positive Moment Mu = 46.00 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 307.00 Kn.m
Max Shear force V = 117.4 Kn
Effective depth of beam d = 660 mm 700 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.176 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.733 d mm
leverarm limited to 0.95d
Then , Z = 0.733 d mm = 484 mm

Area of tension reinforcement.

 As=M*10^6/0.87/fy/Z 263.40177 sq.mm
Provide 2 20 mmdia
0 0 mmdia
Area of tension reinf pro: 628 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 660 mm
K=M/(bd^2fcu) 0.176
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 0.733 d mm
Z = 0.733 d mm = 484 mm
As = 1757.9205 sq.mm
Provide top 2 20 mmdia
4 20 mmdia
Area of top reinf: provided = 1884 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 0.476
T3.9P3/11 Design shear stress, vc = 0.493 N/sq.mm 1
Actual shear stress,v=V/b/d 0.889 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 458.0286 mmor.75*d 495
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 BEAM DESIGN
Name the beam B16
Refer: Calculations Results
Analysis of beam:-
Span = 7.1 m Width = 200 mm
Depth = 800 mm Beam B16
b= 200 mm
Loadings:- D= 800 mm
Block&beams 14 kn/m From slab = 13.5 kn/m Bott-st 3 Y- 20
Total load = 27.5 kn/m Factored = 41.25 kn/m B.curt 2 Y- 20
Point Loa = 0 kn 2 m from left Top 2 Y- 20
Point Loa = 0 kn 0 m from left T.o.c.s 0 Y- 0
Reaction at left 146.4 kn Stir:(1) 8 Y,@ 150
Reaction at right 146.4 kn Stir:(2) 8 Y,@ 150
Point where shear force is zero = 3.55 m F.b 0 nos 0
Maximum span moment = 260 kn-m

Design:-
Span = 7.1 m
B.S.8110 Max Positive Moment Mu = 310 Kn.m
Pa:1,1965 Max Nagative Moment Mu = 0 Kn.m
Max Shear force V = 146.4 Kn
Width of beam b = 200 mm
Effective depth of beam d = 760 mm 800 mm
Charact:st:of concrete fcu = 20 N/sq.mm
Tensile st: of steel fy = 415 N/sq.mm
P3/9 K=M/(bd^2fcu) 0.134 <0.156

Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2 = 0.818 d mm
leverarm limited to 0.95d
Then , Z = 0.818 d mm = 621 mm
 Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 1381.661 sq.mm
Provide 3 20 mmdia
2 20 mmdia
Area of tension reinf pro: 1570 sq.mm Ast provided ok
For negative Moment,
Effective depth d = 760 mm
K=M/(bd^2fcu) 0.000
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2 = 1.000 d mm
Z = 0.950 d mm = 722 mm
As = 0 sq.mm
Provide top 2 20 mmdia
0 0 mmdia
Area of top reinf: provided = 628 sq.mm Ast provided ok

Shear
%age of reinf,p=100As/b/d = 1.033
T3.9P3/11 Design shear stress, vc = 0.639 N/sq.mm 1
Actual shear stress,v=V/b/d 0.963 N/sq.mm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 558.90264 mmor.75*d 570
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia
 DESIGN OF CANTILEVER BEAM
Refer Name of beam CB Results
Design:- Beam CB
Span of beam( L ) = 0.5 m Width = 200 mm b= 200 mm
effective depth( d ) = 565 mm Depth = 600 mm D= 600 mm
fcu = 20 N/sq.mm fy = 415 N/sq.mm bott-st 2 Y- 16
top 4 Y- 16
Loads on beam:- Stir:(1) Y @ 150
Self wt.of beam = 3 kn/m Wall load = 10 kn/m Stir:(2) Y @ 150
Slab load = 10 kn/m Total = 23 kn/m
Factored load = 34.5 kn/m 20
Point load = 20 kn 34.5 kn/m
=
Analise of beam:-
Max bending moment = W*l2/2+Pl
Mu = 14.3125 kn-m 0.5 m
Mu (Nag) = 14.3125 kn-m
Lever arm:-
Z = d ( 0.5+(0.25 - (K / 0.9)1/2
= 0.9690196 * d mm
since the lever arm is limited to 0.95 d = 547.49607 mm
Z = 0.95 * d mm
K = 0.0270186

Area of reinforcement.
To find area of steel required (Ast)req
Mu / ( Bd2fcu )
From Where (fcu ) is the characteristic strength of concrete = 20 N/mm2 ,
IS 456-2000 (Ast)req = Mu / 0.87 fy Z
Table 2 = 72.404764 mm2
Where fy is charateristic strength of steel = 415 N/mm2 , from IS 456 2000
Provide top 4 16 mmdia
Area of top reinf: provided = 803.84 sq.mm
 Ast provided ok
Provide top 2 16 mmdia
Area of top reinf: provided = 401.92 sq.mm
Ast provided ok

Check for Shear :-

Max S.F ( Vu ) = 1.5((wl)+P)) = 47.3 Kn
hence (Vu) = 47 Kn
%age of reinf,pt = 100As/b/d
Pt = 0.04 %
From The design shear strength = 0.61 Tcb.d = 68.93 Kn
IS 456-2000 (Vu-Tcb.d)/d = -0.383717 Kn/cm
Table 61 Hence Provide : - Y 8 @ 150 C/C

Check for Deflection : -

Max def ( De ) = (W14/8EI)+(P13/3EI)
E = 5700*(fcu)0.5 = 25491.17
I = BD3/12 = 3600000000
De = 0.0120179
l / 500 = 1
since De < l / 500
The beam is Safe against deflection
 DESIGN OF CANTILEVER BEAM
Refer Name of beam CB Results
Design:- Beam CB
Span of beam( L ) = 1m Width = 200 mm b= 200 mm
effective depth( d ) = 665 mm Depth = 700 mm D= 700 mm
fcu = 20 N/sq.mm fy = 415 N/sq.mm bott-st 2 Y- 20
top 4 Y- 20
Loads on beam:- Stir:(1) Y @ 150
Self wt.of beam = 3.5 kn/m Wall load = 10 kn/m Stir:(2) Y @ 150
Slab load = 10 kn/m Total = 23.5 kn/m
Factored load = 35.25 kn/m 140
Point load = 140 kn 35.25 kn/m
=
Analise of beam:-
Max bending moment = W*l2/2+Pl
Mu = 157.625 kn-m 1m
Mu (Nag) = 157.625 kn-m
Lever arm:-
Z = d ( 0.5+(0.25 - (K / 0.9)1/2
= 0.9773449 * d mm
since the lever arm is limited to 0.95 d = 649.93438 mm
Z = 0.95 * d mm
K = 0.0199276

Area of reinforcement.
To find area of steel required (Ast)req
Mu / ( Bd2fcu )
From Where (fcu ) is the characteristic strength of concrete = 20 N/mm2 ,
IS 456-2000 (Ast)req = Mu / 0.87 fy Z
Table 2 = 671.71994 mm2
Where fy is charateristic strength of steel = 415 N/mm2 , from IS 456 2000
Provide top 4 20 mmdia
Area of top reinf: provided = 1256 sq.mm
 Ast provided ok
Provide top 2 20 mmdia
Area of top reinf: provided = 628 sq.mm
Ast provided ok

Check for Shear :-

Max S.F ( Vu ) = 1.5((wl)+P)) = 245.3 Kn
hence (Vu) = 245 Kn
%age of reinf,pt = 100As/b/d
Pt = 0.18 %
From The design shear strength = 0.61 Tcb.d = 81.13 Kn
IS 456-2000 (Vu-Tcb.d)/d = 2.4679699 Kn/cm
Table 61 Hence Provide : - Y 8 @ 150 C/C

Check for Deflection : -

Max def ( De ) = (W14/8EI)+(P13/3EI)
E = 5700*(fcu)0.5 = 25491.17
I = BD3/12 = 5716666666.66667
De = 0.3504757
l / 500 = 2
since De < l / 500
The beam is Safe against deflection
 Ref Beam marked;- H.B 1 Summery
Datas;-
Length of beam = 2400 mm Width of beam = 400 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 320 mm Cover (d') = 40 mm
Provide depth = 320 mm Eff. Depth (d) = 280 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3.2 KN/m
Slab load = 16 KN/m Total load = 29.2 KN/m
Factored load = 43.8 KN/m
Point load 1 = 0 KN a = 0m b = 0m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 31.54 KN-m

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 b(req) = 146 mm

b(req)<b(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
3.2E+07 = -101094 Ast + 18.73 Ast2
Ast = 0.00 mm2
Ast(min) = 0.87xbxd/fy = 268 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 0.0 say 4

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 52.56 KN
2
Shear stress(Vv) = 0.41 N/mm
Pt = 100xAst/bxd
Pt = 0.55 %
For M20 and pt = 0.55 fiom table (26) IS 456-2000
Vc = 0.23 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 23120 N
Providing 8 mm ф bars
 Asv = 100.5 mm2
Minimum steel for stirrups
Provide 8 mm ф bars@ 150 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
400 320 4 y14 - 4y12 - y8 @ 15 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- H.B 2 Summery
Datas;-
Length of beam = 3200 mm Width of beam = 600 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 320 mm Cover (d') = 40 mm
Provide depth = 320 mm Eff. Depth (d) = 280 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 4.8 KN/m
Slab load = 20 KN/m Total load = 34.8 KN/m
Factored load = 52.2 KN/m
Point load 1 = 0 KN a = 1.3 m b = 1.9 m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 66.82 KN-m

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 b(req) = 309 mm

b(req)<b(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
6.7E+07 = -101094 Ast + 12.49 Ast2
Ast = 0.00 mm2
Ast(min) = 0.87xbxd/fy = 403 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 0.0 say 6

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 83.52 KN
2
Shear stress(Vv) = 0.44 N/mm
Pt = 100xAst/bxd
Pt = 0.55 %
For M20 and pt = 0.55 fiom table (26) IS 456-2000
Vc = 0.3 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 25920 N
 Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Provide 8 mm ф bars@ 150 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
600 320 6 y14 - 6y14 - y8 @ 15 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- H.B 3 Summery
Datas;-
Length of beam = 4200 mm Width of beam = 700 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 320 mm Cover (d') = 40 mm
Provide depth = 320 mm Eff. Depth (d) = 280 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 5.6 KN/m
Slab load = 22 KN/m Total load = 37.6 KN/m
Factored load = 56.4 KN/m
Point load 1 = 0 KN a = 1.3 m b = 2.9 m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 124.4 KN-m

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 b(req) = 575 mm

b(req)<b(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.2E+08 = -101094 Ast + 10.70 Ast2
Ast = 0.00 mm2
Ast(min) = 0.87xbxd/fy = 470 mm2

Find Number of bars;-

Assume dia of bars, = 16 mm 0.0 say 7

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 118.44 KN
2
Shear stress(Vv) = 0.53 N/mm
Pt = 100xAst/bxd
Pt = 0.72 %
For M20 and pt = 0.72 fiom table (26) IS 456-2000
Vc = 0.3 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 51240 N
 Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Provide 8 mm ф bars@ 150 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
700 320 7 y16 - 7y14 3y16 y8 @ 15 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- H.B 4 Summery
Datas;-
Length of beam = 4000 mm Width of beam = 900 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 320 mm Cover (d') = 40 mm
Provide depth = 320 mm Eff. Depth (d) = 280 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 7.2 KN/m
Slab load = 22 KN/m Total load = 39.2 KN/m
Factored load = 58.8 KN/m
Point load 1 = 60 KN a = 2m b = 2m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 177.6 KN-m

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 b(req) = 821 mm

b(req)<b(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.8E+08 = -101094 Ast + 8.32 Ast2
Ast = 0.00 mm2
Ast(min) = 0.87xbxd/fy = 604 mm2

Find Number of bars;-

Assume dia of bars, = 16 mm 0.0 say 10

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 117.6 KN
2
Shear stress(Vv) = 0.41 N/mm
Pt = 100xAst/bxd
Pt = 0.80 %
For M20 and pt = 0.80 fiom table (26) IS 456-2000
Vc = 0.3 N/mm2
Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 31200 N
 Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Provide 8 mm ф bars@ 150 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
900 320 10 y16 - 10y14 - y8 @ 15 cmc/c
 DESIGN CALCULATIONS
REF COLUMN MARK;- C1 Summery
Factored load = 550 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 1 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
550 = 7.92 A g + 2.7805 A g
2
Ag = 51399.5 mm
D = 257 mm Dpro = 500 mm
Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 36 mm eay = 29 mm
Max = 19.8 KN-m May = 15.95 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 1 % reinforcement for the first trial
SP-16 P/fck = 0.05 Pu/Ag = 16.5
Chart-63 Puz = 1650 KN d' = 50 mm
d'/D = 0.10
SP-16 K1 = 0.207 K2 = 0.082
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 422.2
K = 0.90 ≤1 OK

Additional moments are modified as;-

Max = 17.74 KN-m May = 14.29 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 22.4667 ex min = 25 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 12.3567 KN-m Muy min = 6.857 KN-m

Total moment;-
Mux = 32.1567 KN-m Muy = 22.81 KN-m
SP-16 (Pu/fckxbxD) = 0.28 Mu/fckxbxD2 0.095
Chart-44 Mux1 = 95 KN-m Muy1 = 38 KN-m
Mux/Mux1 = 0.34 Muy/Muy1 = 0.6
Pu/Puz = 0.33
SP-16 Muy/Muy1 = 0.75 > 0.60 OK
Chart-64
Area of steel required;-
Ast = PbD/100 1000 mm2
Assume 14 mm bars 6 Say 6
Summery
Column size (mm) Main Reinforcement Stirrups
200 500 6 y 14 Y8 @ 15c/c
 DESIGN CALCULATIONS
REF COLUMN MARK;- C2 Summery
Factored load = 650 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 1.1 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
650 = 7.92 A g + 2.7805 A g
2
Ag = 60744.8 mm
D = 304 mm Dpro = 500 mm
Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 36 mm eay = 29 mm
Max = 23.4 KN-m May = 18.85 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 1.1 % reinforcement for the first trial
SP-16 P/fck = 0.055 Pu/Ag = 16.5
Chart-63 Puz = 1650 KN d' = 50 mm
d'/D = 0.10
SP-16 K1 = 0.207 K2 = 0.082
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 423.02
K = 0.82 ≤1 OK

Additional moments are modified as;-

Max = 19.07 KN-m May = 15.363 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 22.4667 ex min = 25 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 14.6033 KN-m Muy min = 8.1033 KN-m

Total moment;-
Mux = 38.0033 KN-m Muy = 26.953 KN-m
SP-16 (Pu/fckxbxD) = 0.33 Mu/fckxbxD2 0.090
Chart-44 Mux1 = 90 KN-m Muy1 = 36 KN-m
Mux/Mux1 = 0.42 Muy/Muy1 = 0.7487
Pu/Puz = 0.39
SP-16 Muy/Muy1 = 0.77 > 0.75 OK
Chart-64
Area of steel required;-
Ast = PbD/100 1100 mm2
Assume 16 mm bars 5 Say 6
Summery
Column size (mm) Main Reinforcement Stirrups
200 500 6 y 16 Y8 @ 15c/c
REF COLUMN MARK;- C3 Summery
Factored load = 750 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 1 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
750 = 7.92 A g + 2.7805 A g
2
Ag = 70090.2 mm
D = 350 mm Dpro = 600 mm
Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 43.2 mm eay = 29 mm
Max = 32.4 KN-m May = 21.75 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 1 % reinforcement for the first trial
SP-16 P/fck = 0.05 Pu/Ag = 16.5
Chart-63 Puz = 1980 KN d' = 50 mm
d'/D = 0.08
SP-16 K1 = 0.212 K2 = 0.088
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 519.31
K = 0.84 ≤1 OK

Additional moments are modified as;-

Max = 27.28 KN-m May = 18.315 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 25.8 ex min = 30 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 19.35 KN-m Muy min = 9.35 KN-m

Total moment;-
Mux = 51.75 KN-m Muy = 31.1 KN-m
SP-16 (Pu/fckxbxD) = 0.31 Mu/fckxbxD2 0.100
Chart-44 Mux1 = 144 KN-m Muy1 = 48 KN-m
Mux/Mux1 = 0.36 Muy/Muy1 = 0.6479
Pu/Puz = 0.38
SP-16 Muy/Muy1 = 0.78 > 0.65 OK
Chart-64
Area of steel required;-
Ast = PbD/100 1200 mm2
Assume 14 mm bars 8 Say 8
Summery
Column size (mm) Main Reinforcement Stirrups
200 600 8 y 14 Y8 @ 15c/c
 DESIGN CALCULATIONS
REF COLUMN MARK;- C4 Summery
Factored load = 850 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 1.1 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
850 = 7.92 A g + 2.7805 A g
2
Ag = 79435.5 mm
D = 397 mm Dpro = 600 mm
Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 43.2 mm eay = 29 mm
Max = 36.72 KN-m May = 24.65 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 1.1 % reinforcement for the first trial
SP-16 P/fck = 0.055 Pu/Ag = 16.5
Chart-63 Puz = 1980 KN d' = 50 mm
d'/D = 0.08
SP-16 K1 = 0.212 K2 = 0.088
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 520.36
K = 0.77 ≤1 OK

Additional moments are modified as;-

Max = 28.43 KN-m May = 19.083 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 25.8 ex min = 30 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 21.93 KN-m Muy min = 10.597 KN-m

Total moment;-
Mux = 58.65 KN-m Muy = 35.247 KN-m
SP-16 (Pu/fckxbxD) = 0.35 Mu/fckxbxD2 0.100
Chart-44 Mux1 = 144 KN-m Muy1 = 48 KN-m
Mux/Mux1 = 0.41 Muy/Muy1 = 0.7343
Pu/Puz = 0.43
SP-16 Muy/Muy1 = 0.78 > 0.73 OK
Chart-64
Area of steel required;-
Ast = PbD/100 1320 mm2
Assume 16 mm bars 7 Say 8
Summery
Column size (mm) Main Reinforcement Stirrups
200 600 8 y 16 Y8 @ 15c/c
 DESIGN CALCULATIONS
REF COLUMN MARK;- C5 Summery
Factored load = 1100 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 1.5 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
1100 = 7.92 A g + 2.7805 A g
2
Ag = 102799 mm
D = 514 mm Dpro = 700 mm
Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 50.4 mm eay = 29 mm
Max = 55.44 KN-m May = 31.9 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 1.5 % reinforcement for the first trial
SP-16 P/fck = 0.075 Pu/Ag = 16.5
Chart-63 Puz = 2310 KN d' = 50 mm
d'/D = 0.07
SP-16 K1 = 0.214 K2 = 0.090
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 618.1
K = 0.72 ≤1 OK

Additional moments are modified as;-

Max = 39.65 KN-m May = 22.81 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 29.1333 ex min = 35 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 32.0467 KN-m Muy min = 13.71 KN-m

Total moment;-
Mux = 87.4867 KN-m Muy = 45.61 KN-m
SP-16 (Pu/fckxbxD) = 0.39 Mu/fckxbxD2 0.110
Chart-44 Mux1 = 215.6 KN-m Muy1 = 61.6 KN-m
Mux/Mux1 = 0.41 Muy/Muy1 = 0.74
Pu/Puz = 0.48
SP-16 Muy/Muy1 = 0.82 > 0.74 OK
Chart-64
Area of steel required;-
Ast = PbD/100 2100 mm2
Assume 16 mm bars 10 Say 10
Summery
Column size (mm) Main Reinforcement Stirrups
200 700 10 y 16 Y8 @ 15c/c
 DESIGN CALCULATIONS
REF COLUMN MARK;- C6 Summery
Factored load = 1250 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 1.9 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
1250 = 7.92 A g + 2.7805 A g
2
Ag = 116817 mm
D = 584 mm Dpro = 700 mm
Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 50.4 mm eay = 29 mm
Max = 63 KN-m May = 36.25 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 1.9 % reinforcement for the first trial
SP-16 P/fck = 0.095 Pu/Ag = 16.5
Chart-63 Puz = 2310 KN d' = 50 mm
d'/D = 0.07
SP-16 K1 = 0.214 K2 = 0.090
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 623.1
K = 0.63 ≤1 OK

Additional moments are modified as;-

Max = 39.59 KN-m May = 22.78 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 29.1333 ex min = 35 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 36.4167 KN-m Muy min = 15.58 KN-m

Total moment;-
Mux = 99.4167 KN-m Muy = 51.83 KN-m
SP-16 (Pu/fckxbxD) = 0.45 Mu/fckxbxD2 0.115
Chart-44 Mux1 = 225.4 KN-m Muy1 = 64.4 KN-m
Mux/Mux1 = 0.44 Muy/Muy1 = 0.805
Pu/Puz = 0.54
SP-16 Muy/Muy1 = 0.82 > 0.80 OK
Chart-64
Area of steel required;-
Ast = PbD/100 2660 mm2
Assume 16 mm bars 13 Say 14
Summery
Column size (mm) Main Reinforcement Stirrups
200 700 14 y 16 Y8 @ 15c/c
 DESIGN CALCULATIONS
REF COLUMN MARK;- C7 Summery
Factored load = 1450 KN
Floor height = 3.4 m
Un supported lenth in -x- direction = 2.9 m
Un supported lenth in -y- direction = 2.9 m
Width of column = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Check for slenderness ratio;-

Condition, (L/rmin) >12, Long column
(L/rmin) = 17
Column is slender

Design of column as;-

Assume ( Asc) = 2 %A g Asc = 0.01 A g
Ac = Ag-Asc Ac = 0.99 A g
Pu = .4 fck Ac+.67 fyAsc
1450 = 7.92 A g + 2.7805 A g
Ag = 135508 mm2
D = 678 mm Dpro = 800 mm

Additional Moments;-
SP-16 eax/D = 0.072 eay/b = 0.145
Table I eax = 57.6 mm eay = 29 mm
Max = 83.52 KN-m May = 42.05 KN-m

Modifaction factor;-
K = {(Puz-Pu)/(Puz-Pb)}
Assuming 2 % reinforcement for the first trial
SP-16 P/fck = 0.1 Pu/Ag = 16.5
Chart-63 Puz = 2640 KN d' = 50 mm
d'/D = 0.06
SP-16 K1 = 0.21 K2 = 0.090
Table 60 Pbx=Pby = {K1+K2(P/fck)}fck b D = 700.8
K = 0.61 ≤1 OK

Additional moments are modified as;-

Max = 51.25 KN-m May = 25.8 KN-m

Minimum ecentricities;-
IS 456-2000 ex = 32.4667 ex min = 40 mm
Clause25.4 ey = 12.47 ey min = 10 mm
Mux min = 47.0767 KN-m Muy min = 18.08 KN-m

Total moment;-
 Mux = 130.597 KN-m Muy = 60.13 KN-m
SP-16 (Pu/fckxbxD) = 0.45 Mu/fckxbxD2 0.115
Chart-44 Mux1 = 294.4 KN-m Muy1 = 73.6 KN-m
Mux/Mux1 = 0.44 Muy/Muy1 = 0.817
Pu/Puz = 0.55
SP-16 Muy/Muy1 = 0.83 > 0.82 OK
Chart-64
Area of steel required;-
Ast = PbD/100 3200 mm2
Assume 16 mm bars 16 Say 16
Summery
Column size (mm) Main Reinforcement Stirrups
200 800 16 y 16 Y8 @ 15c/c
 FOOTING DESIGN
REF FOOTING MARKED;- F1 SUMMERY
Design load (wD) = 450 KN
Service load (ws) = 300 KN
Wt of footing+Service load(w) = 330 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
2.20 m2
Provide B = 1.5 m
L = 1.5 m
D = 0.5 m
Area of footing provided = 2.25 m2
Net upward soil pressure(p0) = W/(LXB)
133.33 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.2 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
2.6 m
Area(a*) = 0.42 m2
Punching shear force (V) = Po{(LXB)-(a*)}
243.67 KN
Punching shear stress(Vv) = {V/(pxd)}
0.21 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.65
(L-a)/2 = 0.65
Moment along short direction(per 'm' width) 28.17 KN-m
Moment along long direction(per 'm' width) 28.17 KN-m
Effective depth required;-
d(req) (L) = 147 mm
d(req) (S) = 147 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 469 mm2
Ast (long direction) full width = 469 mm2
Provide steel;-
Ast (S) 14 @ 16 cm c/c 1442 mm2 B= 1.5 m
Ast (L) 14 @ 16 cm c/c 1442 mm 2
L= 1.5 m
 FOOTING DESIGN
REF FOOTING MARKED;- F2 SUMMERY
Design load (wD) = 500 KN
Service load (ws) = 333 KN
Wt of footing+Service load(w) = 367 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
2.44 m2
Provide B = 1.6 m
L = 1.6 m
D = 0.5 m
Area of footing provided = 2.56 m2
Net upward soil pressure(p0) = W/(LXB)
130.21 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
244.47 KN
Punching shear stress(Vv) = {V/(pxd)}
0.16 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.7
(L-a)/2 = 0.5
Moment along short direction(per 'm' width) 31.90 KN-m
Moment along long direction(per 'm' width) 16.28 KN-m
Effective depth required;-
d(req) (L) = 108 mm
d(req) (S) = 151 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 567 mm2
Ast (long direction) full width = 289 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 1641 mm2 B= 1.6 m
Ast (L) 14 @ 15 cm c/c 1641 mm 2
L= 1.6 m
 FOOTING DESIGN
REF FOOTING MARKED;- F3 SUMMERY
Design load (wD) = 650 KN
Service load (ws) = 433 KN
Wt of footing+Service load(w) = 477 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
3.18 m2
Provide B = 1.7 m
L = 1.9 m
D = 0.5 m
Area of footing provided = 3.23 m2
Net upward soil pressure(p0) = W/(LXB)
134.16 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
341.77 KN
Punching shear stress(Vv) = {V/(pxd)}
0.22 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.75
(L-a)/2 = 0.65
Moment along short direction(per 'm' width) 37.73 KN-m
Moment along long direction(per 'm' width) 28.34 KN-m
Effective depth required;-
d(req) (L) = 131 mm
d(req) (S) = 160 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 796 mm2
Ast (long direction) full width = 535 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 1949 mm2 B= 1.7 m
Ast (L) 14 @ 15 cm c/c 1744 mm 2
L= 1.9 m
 FOOTING DESIGN
REF FOOTING MARKED;- F4 SUMMERY
Design load (wD) = 725 KN
Service load (ws) = 483 KN
Wt of footing+Service load(w) = 532 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
3.54 m2
Provide B = 1.8 m
L = 2m
D = 0.5 m
Area of footing provided = 3.6 m2
Net upward soil pressure(p0) = W/(LXB)
134.26 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
391.70 KN
Punching shear stress(Vv) = {V/(pxd)}
0.26 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.8
(L-a)/2 = 0.7
Moment along short direction(per 'm' width) 42.96 KN-m
Moment along long direction(per 'm' width) 32.89 KN-m
Effective depth required;-
d(req) (L) = 137 mm
d(req) (S) = 166 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 954 mm2
Ast (long direction) full width = 658 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2051 Sq-mm B= 1.8 m
Ast (L) 14 @ 15 cm c/c 1846 Sq-mm L= 2m
 FOOTING DESIGN
REF FOOTING MARKED;- F5 SUMMERY
Design load (wD) = 780 KN
Service load (ws) = 520 KN
Wt of footing+Service load(w) = 572 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
3.81 m2
Provide B = 1.9 m
L = 2.1 m
D = 0.5 m
Area of footing provided = 3.99 m2
Net upward soil pressure(p0) = W/(LXB)
130.33 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
431.05 KN
Punching shear stress(Vv) = {V/(pxd)}
0.28 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.85
(L-a)/2 = 0.75
Moment along short direction(per 'm' width) 47.08 KN-m
Moment along long direction(per 'm' width) 36.65 KN-m
Effective depth required;-
d(req) (L) = 142 mm
d(req) (S) = 169 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1098 mm2
Ast (long direction) full width = 773 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2154 Sq-mm B= 1.9 m
Ast (L) 14 @ 15 cm c/c 1949 Sq-mm L= 2.1 m
 FOOTING DESIGN
REF FOOTING MARKED;- F6 SUMMERY
Design load (wD) = 800 KN
Service load (ws) = 533 KN
Wt of footing+Service load(w) = 587 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
3.91 m2
Provide B = 1.9 m
L = 2.2 m
D = 0.5 m
Area of footing provided = 4.18 m2
Net upward soil pressure(p0) = W/(LXB)
127.59 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
446.25 KN
Punching shear stress(Vv) = {V/(pxd)}
0.29 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.85
(L-a)/2 = 0.8
Moment along short direction(per 'm' width) 46.09 KN-m
Moment along long direction(per 'm' width) 40.83 KN-m
Effective depth required;-
d(req) (L) = 146 mm
d(req) (S) = 167 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1126 mm2
Ast (long direction) full width = 862 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2257 Sq-mm B= 1.9 m
Ast (L) 14 @ 15 cm c/c 1949 Sq-mm L= 2.2 m
 FOOTING DESIGN
REF FOOTING MARKED;- F7 SUMMERY
Design load (wD) = 900 KN
Service load (ws) = 600 KN
Wt of footing+Service load(w) = 660 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
4.40 m2
Provide B = 2m
L = 2.2 m
D = 0.5 m
Area of footing provided = 4.4 m2
Net upward soil pressure(p0) = W/(LXB)
136.36 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
506.93 KN
Punching shear stress(Vv) = {V/(pxd)}
0.33 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.9
(L-a)/2 = 0.8
Moment along short direction(per 'm' width) 55.23 KN-m
Moment along long direction(per 'm' width) 43.64 KN-m
Effective depth required;-
d(req) (L) = 151 mm
d(req) (S) = 178 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1349 mm2
Ast (long direction) full width = 969 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2257 Sq-mm B= 2m
Ast (L) 14 @ 15 cm c/c 2051 Sq-mm L= 2.2 m
 FOOTING DESIGN
REF FOOTING MARKED;- F8 SUMMERY
Design load (wD) = 1050 KN
Service load (ws) = 700 KN
Wt of footing+Service load(w) = 770 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
5.13 m2
Provide B = 2m
L = 2.6 m
D = 0.6 m
Area of footing provided = 5.2 m2
Net upward soil pressure(p0) = W/(LXB)
134.62 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.55 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.8 m
Area(a*) = 0.86 m2
Punching shear force (V) = Po{(LXB)-(a*)}
583.89 KN
Punching shear stress(Vv) = {V/(pxd)}
0.28 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 0.9
(L-a)/2 = 1
Moment along short direction(per 'm' width) 54.52 KN-m
Moment along long direction(per 'm' width) 67.31 KN-m
Effective depth required;-
d(req) (L) = 172 mm
d(req) (S) = 177 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1288 mm2
Ast (long direction) full width = 1223 mm2
Provide steel;-
Ast (S) 14 @ 12 cm c/c 3334 Sq-mm B= 2m
Ast (L) 14 @ 12 cm c/c 2564 Sq-mm L= 2.6 m
 FOOTING DESIGN
REF FOOTING MARKED;- F9 SUMMERY
Design load (wD) = 1025 KN
Service load (ws) = 683 KN
Wt of footing+Service load(w) = 752 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
5.01 m2
Provide B = 2.2 m
L = 2.4 m
D = 0.5 m
Area of footing provided = 5.28 m2
Net upward soil pressure(p0) = W/(LXB)
129.42 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.45 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.4 m
Area(a*) = 0.68 m2
Punching shear force (V) = Po{(LXB)-(a*)}
595.00 KN
Punching shear stress(Vv) = {V/(pxd)}
0.39 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 1
(L-a)/2 = 0.9
Moment along short direction(per 'm' width) 64.71 KN-m
Moment along long direction(per 'm' width) 52.41 KN-m
Effective depth required;-
d(req) (L) = 158 mm
d(req) (S) = 184 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1725 mm2
Ast (long direction) full width = 1281 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2462 Sq-mm B= 2.2 m
Ast (L) 14 @ 15 cm c/c 2257 Sq-mm L= 2.4 m
 FOOTING DESIGN
REF FOOTING MARKED;- F10 SUMMERY
Design load (wD) = 1150 KN
Service load (ws) = 767 KN
Wt of footing+Service load(w) = 843 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
5.62 m2
Provide B = 2.2 m
L = 2.6 m
D = 0.55 m
Area of footing provided = 5.72 m2
Net upward soil pressure(p0) = W/(LXB)
134.03 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.5 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.6 m
Area(a*) = 0.77 m2
Punching shear force (V) = Po{(LXB)-(a*)}
663.46 KN
Punching shear stress(Vv) = {V/(pxd)}
0.37 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 1
(L-a)/2 = 1
Moment along short direction(per 'm' width) 67.02 KN-m
Moment along long direction(per 'm' width) 67.02 KN-m
Effective depth required;-
d(req) (L) = 172 mm
d(req) (S) = 187 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1742 mm2
Ast (long direction) full width = 1474 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2667 Sq-mm B= 2.2 m
Ast (L) 14 @ 15 cm c/c 2257 Sq-mm L= 2.6 m
 FOOTING DESIGN
REF FOOTING MARKED;- F11 SUMMERY
Design load (wD) = 1200 KN
Service load (ws) = 800 KN
Wt of footing+Service load(w) = 880 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
5.87 m2
Provide B = 2.3 m
L = 2.6 m
D = 0.55 m
Area of footing provided = 5.98 m2
Net upward soil pressure(p0) = W/(LXB)
133.78 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.5 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.6 m
Area(a*) = 0.77 m2
Punching shear force (V) = Po{(LXB)-(a*)}
696.99 KN
Punching shear stress(Vv) = {V/(pxd)}
0.39 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 1.05
(L-a)/2 = 1
Moment along short direction(per 'm' width) 73.75 KN-m
Moment along long direction(per 'm' width) 66.89 KN-m
Effective depth required;-
d(req) (L) = 172 mm
d(req) (S) = 192 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 1916 mm2
Ast (long direction) full width = 1538 mm2
Provide steel;-
Ast (S) 14 @ 15 cm c/c 2667 Sq-mm B= 2.3 m
Ast (L) 14 @ 15 cm c/c 2359 Sq-mm L= 2.6 m
 FOOTING DESIGN
REF FOOTING MARKED;- F12 SUMMERY
Design load (wD) = 1275 KN
Service load (ws) = 850 KN
Wt of footing+Service load(w) = 935 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
6.23 m2
Provide B = 2.4 m
L = 2.6 m
D = 0.55 m
Area of footing provided = 6.24 m2
Net upward soil pressure(p0) = W/(LXB)
136.22 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.7 m
Effective depth of footing(d) = 0.5 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.8 m
Area(a*) = 0.84 m2
Punching shear force (V) = Po{(LXB)-(a*)}
735.58 KN
Punching shear stress(Vv) = {V/(pxd)}
0.39 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 1.1
(L-a)/2 = 0.95
Moment along short direction(per 'm' width) 82.41 KN-m
Moment along long direction(per 'm' width) 61.47 KN-m
Effective depth required;-
d(req) (L) = 165 mm
d(req) (S) = 199 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 2142 mm2
Ast (long direction) full width = 1475 mm2
Provide steel;-
Ast (S) 14 @ 12 cm c/c 3334 Sq-mm B= 2.4 m
Ast (L) 14 @ 12 cm c/c 3077 Sq-mm L= 2.6 m
 FOOTING DESIGN
REF FOOTING MARKED;- F13 SUMMERY
Design load (wD) = 1450 KN
Service load (ws) = 967 KN
Wt of footing+Service load(w) = 1063 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
7.09 m2
Provide B = 2.5 m
L = 2.9 m
D = 0.6 m
Area of footing provided = 7.25 m2
Net upward soil pressure(p0) = W/(LXB)
133.33 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.8 m
Effective depth of footing(d) = 0.55 m
Perimeter(p) = 2{(a+d)+(b+d)}
4.2 m
Area(a*) = 1.01 m2
Punching shear force (V) = Po{(LXB)-(a*)}
831.67 KN
Punching shear stress(Vv) = {V/(pxd)}
0.36 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 1.15
(L-a)/2 = 1.05
Moment along short direction(per 'm' width) 88.17 KN-m
Moment along long direction(per 'm' width) 73.50 KN-m
Effective depth required;-
d(req) (L) = 171 mm
d(req) (S) = 201 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 2323 mm2
Ast (long direction) full width = 1670 mm2
Provide steel;-
Ast (S) 16 @ 15 cm c/c 3885 Sq-mm B= 2.5 m
Ast (L) 16 @ 15 cm c/c 3349 Sq-mm L= 2.9 m
 FOOTING DESIGN
REF FOOTING MARKED;- F14 SUMMERY
Design load (wD) = 1600 KN
Service load (ws) = 1067 KN
Wt of footing+Service load(w) = 1173 KN
Safe bearing capacity = 150 KN/m2
Area of footing required = (W/S.B.C) m2
7.82 m2
Provide B = 2.6 m
L = 3.1 m
D = 0.6 m
Area of footing provided = 8.06 m2
Net upward soil pressure(p0) = W/(LXB)
132.34 KN/m2
SHEAR CHECK;-
Column size a = 0.2 m
b = 0.6 m
Effective depth of footing(d) = 0.55 m
Perimeter(p) = 2{(a+d)+(b+d)}
3.8 m
Area(a*) = 0.86 m2
Punching shear force (V) = Po{(LXB)-(a*)}
952.52 KN
Punching shear stress(Vv) = {V/(pxd)}
0.46 N/mm2
fy = 415 N/mm2
fck = 20 N/mm2
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Vv<Vc,safe
DESIGN;-
Cantilever Projections, (B-b)/2 = 1.2
(L-a)/2 = 1.25
Moment along short direction(per 'm' width) 95.29 KN-m
Moment along long direction(per 'm' width) 103.39 KN-m
Effective depth required;-
d(req) (L) = 196 mm
d(req) (S) = 205 mm
Provided depth "d"> d(req)
Required steel;-
Ast=M/(230X.87Xd)
Ast (Short direction) full width = 2684 mm2
Ast (long direction) full width = 2443 mm2
Provide steel;-
Ast (S) 16 @ 15 cm c/c 4153 Sq-mm B= 2.6 m
Ast (L) 16 @ 15 cm c/c 3483 Sq-mm L= 3.1 m
 DESIGN CALCULATIONS
REF FOOTING MARKED;- CF4 SUMMERY
Design constant:-
Fy = 415 N/mm2 Fck = 20 N/mm2

Load on footing;-
Factored load Working load
W1 = 1700 KN 1133 KN
W2 = 950 KN 633.33 KN
W3 = 1200 KN 800 KN
SBC of soil = 150 KN/m2
self wt of footing 256.6667 KN
Total weight of footing (Ww) = 2823.3 KN
Area of footing required (Ww/S.B.C)
18.82222 m2
Provide B = 2.4 m L= 6.5 m
D = 0.6 m d = 0.55 m
Provided Area = 15.6 m2
l1 = 1.5 m
l2 = 3m
Uplift pressure = 164.5299 KN/m2
C.G Column load(X*) = (W2xlI+W3xl2)/(W1+W2+W3)
X* 1.31 m
Proction(a1) = (L/2)- 1.94 m
Proction(a2) = (L-a1-l2) = 1.6 m

Bending moment;-
Moment @ A = 746.76 KN-m
Moment @ B = 477.52 KN-m
Moment @ c = 111.06 KN-m

Required depth;-
dreq = SQRT(Mux10^6 /(fckxb)
455.257 mm
d(req)<d(pro), "OK"

Shear check;-
S.F@ Left of A = 767.95 KN
S.F@ Right of A = 365.38 KN
S.F@ Right of C = 614.10 KN
S.F@Left of C = 185.90 KN
S.F Will be zero at distance Xfrom' A'
 X = 2.87 m
Permissible shear stress (Vc) = .16(fck)^1/2
0.72 N/mm2
Punching shear force (V) = 614.1 KN
Punching shear stress (Vv) = V/(Bxd)
0.47 N/mm2
Vv<Vc, Safe

Required Area of steel;-

Ast = ( Mu6/.87/230/d)
4339.0

Provided Area of steel;-

Short T&B = 16 150 mm c/c 8708 mm2 "OK"
Long T&B = 16 150 mm c/c 3215 mm2 "OK"

Summery;-
Size
B = 2.4 m
L = 6.5 m
D = 0.6 m

Ast Short= y 14 @ 15 cm c/c T&B

Long = y 14 @ 15 cm c/c T&B
 DESIGN CALCULATIONS
REF FOOTING MARKED;- CF1
Datas;-
Load on column C1 = 450 KN
Load on column C2 = 500 KN
Total load with 10% self wt = 1045 KN Size provided ok
2
Safe bearing capacity = 150 KN/m
Design;-
2
Area of footing required = 7.0 m
c/c distance of column (d) = 1.55 m
Width = 2.2 m
Lenth = 3.6 m
2
Area of footing provided = 7.92 m
2
Net upwared soil pr (P0) = 119.9 KN/m
C.G Column load(x*) = (W2xL)/(W1+W2) Column size
= 0.8 m B= 200 mm
Projection = (L/2)-X* 1.0 m D= 600 mm
Projection = (L-a1-b) 1.1 m
Projection(short direction) = b/2 1.1 m

Bending moment;-
Consider 1m width of footing
Max sagging B.M in long direction = Poxa22/2 68.12575 KN-m
Max hogging B.M in long direction = Poxd2/10 28.81787 KN-m
Max sagging B.M in short direction= Poxa32/2 72.56944 KN-m
Mu max = 68.12575 KN-m

Effective depth;-
From max bending moment
Mu max^6/R*b^0.5 = 322 mm
 From punching shear consideration
= Wmax/(2*(b+D)*1 = 313 mm
Max eff depth required = 322 mm
Over all depth provided = 500 mm d' = 50 mm
Effective depth provided = 450 mm

Area of steel required;-

Long direction bottom steel = Mu1^6/(fstxjxd) Ast1 = 731.3553 mm2
Long direction top steel = Mu2^6/(fstxjxd) Ast2 = 309.3705 mm2
Short direct top&bott steel = Mu3^6/(fstxjxd) Ast3 = 779.0601 mm2

Area of steel provided;-

Long direction = Y 14 @ 15 cm c/c T&B = 2051.467 mm2 OK
Short direction = Y 14 @ 15 cm c/c T&B = 2051.467 mm2 OK

Summery;-
Length = 3.60 m Width = 2.2 m
Depth = 0.5 m
 DESIGN CALCULATIONS
REF FOOTING MARKED;- CF2
Datas;-
Load on column C1 = 600 KN
Load on column C2 = 625 KN
Total load with 10% self wt = 1347.5 KN Size provided ok
2
Safe bearing capacity = 150 KN/m
Design;-
2
Area of footing required = 9.0 m
c/c distance of column (d) = 1.8 m
Width = 2.4 m
Lenth = 3.8 m
2
Area of footing provided = 9.12 m
2
Net upwared soil pr (P0) = 134.3 KN/m
C.G Column load(x*) = (W2xL)/(W1+W2) Column size
= 0.9 m B= 200 mm
Projection = (L/2)-X* 1.0 m D= 700 mm
Projection = (L-a1-b) 1.0 m
Projection(short direction) = b/2 1.2 m

Bending moment;-
Consider 1m width of footing
Max sagging B.M in long direction = Poxa22/2 69.64985 KN-m
Max hogging B.M in long direction = Poxd2/10 43.51974 KN-m
Max sagging B.M in short direction= Poxa32/2 96.71053 KN-m
Mu max = 69.64985 KN-m

Effective depth;-
From max bending moment
Mu max^6/R*b^0.5 = 326 mm
 From punching shear consideration
= Wmax/(2*(b+D)*1 = 347 mm
Max eff depth required = 347 mm
Over all depth provided = 500 mm d' = 50 mm
Effective depth provided = 450 mm

Area of steel required;-

Long direction bottom steel = Mu1^6/(fstxjxd) Ast1 = 747.7171 mm2
Long direction top steel = Mu2^6/(fstxjxd) Ast2 = 467.2006 mm2
Short direct top&bott steel = Mu3^6/(fstxjxd) Ast3 = 1038.224 mm2

Area of steel provided;-

Long direction = Y 14 @ 15 cm c/c T&B = 2051.467 mm2 OK
Short direction = Y 14 @ 15 cm c/c T&B = 2051.467 mm2 OK

Summery;-
Length = 3.80 m Width = 2.4 m
Depth = 0.5 m
 DESIGN CALCULATIONS
Ref Beam marked;- PB1 Summery
Datas;-
Length of beam = 2000 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 200 mm Cover (d') = 40 mm
Provide depth = 400 mm Eff. Depth (d) = 360 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2 KN/m
Slab load = 0 KN/m Total load = 12 KN/m
Factored load = 18 KN/m
Point load 1 = 0 KN a = 1m b = 1m
Point load 2 = 0 KN a = 1.7 m b = 0.3 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 9 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 128 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
9000000 = -129978 Ast + 37.46 Ast2
Ast = 70.68 mm2
Ast(min) = 0.87xbxd/fy = 168 mm2

Find Number of bars;-

Assume dia of bars, = 12 mm 1.5 say 2

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 18 KN
2
Shear stress(Vv) = 0.23 N/mm
Pt = 100xAst/bxd
Pt = 0.31 %
For M20 and pt = 0.31 fiom table (26) IS 456-2000
Vc = 0.18 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 3600 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 290 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 400 2 y12 - 2y12 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB2 Summery
Datas;-
Length of beam = 4200 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 420 mm Cover (d') = 40 mm
Provide depth = 500 mm Eff. Depth (d) = 460 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2.5 KN/m
Slab load = 0 KN/m Total load = 12.5 KN/m
Factored load = 18.75 KN/m
Point load 1 = 0 KN a = 2m b = 2.2 m
Point load 2 = 0 KN a = 1.7 m b = 2.5 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 41.34 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 39.16 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 274 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
4.1E+07 = -166083 Ast + 37.46 Ast2
Ast = 264.74 mm2
Ast(min) = 0.87xbxd/fy = 210 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 1.7 say 2

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 39.38 KN
2
Shear stress(Vv) = 0.39 N/mm
Pt = 100xAst/bxd
Pt = 0.33 %
For M20 and pt = 0.33 fiom table (26) IS 456-2000
Vc = 0.25 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 14375 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 227 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 500 2 y14 - 2y14 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB3 Summery
Datas;-
Length of beam = 4200 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 420 mm Cover (d') = 40 mm
Provide depth = 500 mm Eff. Depth (d) = 460 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2.5 KN/m
Slab load = 0 KN/m Total load = 12.5 KN/m
Factored load = 18.75 KN/m
Point load 1 = 0 KN a = 1.25 m b = 2.95 m
Point load 2 = 0 KN a = 1.55 m b = 2.65 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 41.34 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 39.06 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 274 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
4.1E+07 = -166083 Ast + 37.46 Ast2
Ast = 264.74 mm2
Ast(min) = 0.87xbxd/fy = 210 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 1.7 say 2

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 39.38 KN
2
Shear stress(Vv) = 0.39 N/mm
Pt = 100xAst/bxd
Pt = 0.33 %
For M20 and pt = 0.33 fiom table (26) IS 456-2000
Vc = 0.22 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 17375 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 227 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 500 2 y14 - 2y14 2y14 y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB4 Summery
Datas;-
Length of beam = 1500 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 150 mm Cover (d') = 40 mm
Provide depth = 500 mm Eff. Depth (d) = 460 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2.5 KN/m
Slab load = 0 KN/m Total load = 12.5 KN/m
Factored load = 18.75 KN/m
Point load 1 = 0 KN a = 0.7 m b = 1.3 m
Point load 2 = 0 KN a = 0m b = 0m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 5.273 KN-m
Ultimate moment;- (For cntinious beam) By Moment distribution method
M = 45 KN-m (Nagative)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 286 mm

d(req)<d(pro), OK

Top Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
4.5E+07 = -166083 Ast + 37.46 Ast2
Ast = 289.90 mm2
Ast(min) = 0.87xbxd/fy = 210 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 1.9 say 4

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 14.06 KN
2
Shear stress(Vv) = 0.14 N/mm
Pt = 100xAst/bxd
Pt = 0.32 %
For M20 and pt = 0.32 fiom table (26) IS 456-2000
Vc = 0.1 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 4062.5 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 227 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 500 2 y14 - 4y14 y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB5 Summery
Datas;-
Length of beam = 5200 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 520 mm Cover (d') = 40 mm
Provide depth = 500 mm Eff. Depth (d) = 460 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2.5 KN/m
Slab load = 0 KN/m Total load = 12.5 KN/m
Factored load = 18.75 KN/m
Point load 1 = 15 KN a = 1m b = 4.2 m
Point load 2 = 0 KN a = 1.25 m b = 3.95 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 75.49 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 63.38 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 370 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
7.5E+07 = -166083 Ast + 37.46 Ast2
Ast = 514.16 mm2
Ast(min) = 0.87xbxd/fy = 210 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 3.3 say 3

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 48.75 KN
2
Shear stress(Vv) = 0.49 N/mm
Pt = 100xAst/bxd
Pt = 0.50 %
For M20 and pt = 0.50 fiom table (26) IS 456-2000
Vc = 0.25 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 23750 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 227 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 500 3 y14 2y14 2y14 2y14 y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB6 Summery
Datas;-
Length of beam = 5200 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 520 mm Cover (d') = 40 mm
Provide depth = 500 mm Eff. Depth (d) = 460 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 2.5 KN/m
Slab load = 0 KN/m Total load = 12.5 KN/m
Factored load = 18.75 KN/m
Point load 1 = 25 KN a = 1.2 m b = 4m
Point load 2 = 0 KN a = 2.25 m b = 2.95 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 86.45 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 396 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
8.6E+07 = -166083 Ast + 37.46 Ast2
Ast = 602.37 mm2
Ast(min) = 0.87xbxd/fy = 210 mm2

Find Number of bars;-

Assume dia of bars, = 14 mm 3.9 say 3

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 48.75 KN
2
Shear stress(Vv) = 0.49 N/mm
Pt = 100xAst/bxd
Pt = 0.50 %
For M20 and pt = 0.50 fiom table (26) IS 456-2000
Vc = 0.22 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 26750 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 227 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 500 3 y14 2y14 2y14 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB7 Summery
Datas;-
Length of beam = 6000 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 600 mm Cover (d') = 40 mm
Provide depth = 700 mm Eff. Depth (d) = 660 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3.5 KN/m
Slab load = 0 KN/m Total load = 13.5 KN/m
Factored load = 20.25 KN/m
Point load 1 = 105 KN a = 2m b = 4m
Point load 2 = 0 KN a = 2.25 m b = 3.75 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 231.1 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 0 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 647 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
2.3E+08 = -238293 Ast + 37.46 Ast2
Ast = 1194.04 mm2
Ast(min) = 0.87xbxd/fy = 293 mm2

Find Number of bars;-

Assume dia of bars, = 18 mm 4.7 say 3

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 60.75 KN
2
Shear stress(Vv) = 0.43 N/mm
Pt = 100xAst/bxd
Pt = 0.58 %
For M20 and pt = 0.58 fiom table (26) IS 456-2000
Vc = 0.22 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 29950 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 158 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 700 3 y18 2y18 2y18 - y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB8 Summery
Datas;-
Length of beam = 6900 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 690 mm Cover (d') = 40 mm
Provide depth = 600 mm Eff. Depth (d) = 560 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3 KN/m
Slab load = 0 KN/m Total load = 13 KN/m
Factored load = 19.5 KN/m
Point load 1 = 0 KN a = 1.2 m b = 5.7 m
Point load 2 = 0 KN a = 2.25 m b = 4.65 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 116 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 77.35 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 459 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
1.2E+08 = -202188 Ast + 37.46 Ast2
Ast = 652.96 mm2
Ast(min) = 0.87xbxd/fy = 252 mm2

Find Number of bars;-

Assume dia of bars, = 16 mm 3.2 say 3

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 67.28 KN
2
Shear stress(Vv) = 0.56 N/mm
Pt = 100xAst/bxd
Pt = 0.54 %
For M20 and pt = 0.54 fiom table (26) IS 456-2000
Vc = 0.25 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 37275 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 186 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 600 3 y16 2y14 2y16 2y16 y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref Beam marked;- PB9 Summery
Datas;-
Length of beam = 4000 mm Width of beam = 200 mm
fy = 415 N/mm2 fck = 20 N/mm2

Daesign;-
Assume (Span/Depth) ratio = (1/10)to(1/12)
Depth(req) D = 400 mm Cover (d') = 40 mm
Provide depth = 600 mm Eff. Depth (d) = 560 mm

Loadings;-
Wall load = 10 KN/m Self wt of beam = 3 KN/m
Slab load = 0 KN/m Total load = 13 KN/m
Factored load = 19.5 KN/m
Point load 1 = 0 KN a = 1.2 m b = 2.8 m
Point load 2 = 0 KN a = 2.25 m b = 1.75 m

Ultimate moment;- (For simply suported beam)

M = 0.125XWXL2+Wab/l M = 39 KN-m
Ultimate moment;- (For cntinious beam) By moment distribution method
M = 77.35 KN-m (Possitive)

Check for effective depth;-

IS456-2000 Mu limit = 2.76bd2 d(req) = 266 mm

d(req)<d(pro), OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
3.9E+07 = -202188 Ast + 37.46 Ast2
Ast = 200.32 mm2
Ast(min) = 0.87xbxd/fy = 252 mm2

Find Number of bars;-

Assume dia of bars, = 16 mm 1.0 say 2

Shear Reinforcement;-
Shear force(Vu) = Wl/2 = 39 KN
2
Shear stress(Vv) = 0.33 N/mm
Pt = 100xAst/bxd
Pt = 0.36 %
For M20 and pt = 0.36 fiom table (26) IS 456-2000
Vc = 0.22 N/mm2
 Vv > Vc Shear reinforcement is need
Shear force = Vu-Vcxbxd 12600 N
Providing 8 mm ф bars
Asv = 100.5 mm2
Minimum steel for stirrups
Sv = ( fy Asv )/0.4d 186 mm
Provide 8 mm ф bars@ 200 mm c/c
Summery;-
Size(mm) Reinforcement
Width Depth Bottom Curt Top E .O.C.S Stirrups
200 600 2 y16 - 2y16 2y16 y8 @ 20 cmc/c
 DESIGN CALCULATIONS
Ref SLAB MARK;- S1 Summery
Datas;-
Lx = 1.9 m Ly = 3.2 m
fy = 415 N/Sq-mm fck = 20 N/Sq-mm
ly/lx = 1.7 <2, so slab is two way

Loadings;-
Self wt = 3.25 kN/Sq-m F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m Sunk load = 2 kN/Sq-m
Total load = 8.75 kN/Sq-m F .Load = 13.13 kN/Sq-m

Required depth;-
d = Span/(B.VxM.F) B.V = 20 (ss)
Assume 0.2 % of steel M.F = 1.6
Eff. Depth = 5.938 cm

Provided depth;-
D= 13 cm dpro = 10.5 cm

Bending moment;- Conditions; Two Adjacent Edges discontinious

Nagative moment
Page 91 ax = 0.060 Mux = 2.843 Kn-m
ratio ay = 0.047 Muy = 2.227 Kn-m
1.7 Possitive moment
case 4 ax = 0.045 Mux = 2.132 Kn-m
ay = 0.035 Muy = 1.658 Kn-m
Maximum moment = 2.84 Kn-m

Check for depth;- Computation of depth from bending

d = SQRT(Mux/.138xfckxb) 3 cm
dreq<dpro OK
Using 10 mm dia bars
Steel Reinforcement calculation;- (Required)
Using 10 mm dia bars
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Shorter direction Longer direction
Ast = 76.17 Sq-mm Ast = 53.81 Sq-mm
Ast(min) = 0.12 %bXD 156 mm2

Provided Stell Reinforcement;-

Shorter direction y 10 @ 150 mm c/c 523 Sq-mm
Ast provided ok
longer direction y 10 @ 150 mm c/c 523 Sq-mm
Ast provided ok
Check for deflection;- At the mid span,
100Ast/bD = 0.06 % M.F = 1.6
Actual ratio = Span/Depth 18.10
Permissible stress = B.VxM.F 32 > actual ratio, Safe

Summery of slab
Thick(cm) Reinforcement
Shorter direction Longer direction
13 Y10mm @ 15cmc/c Y10mm @ 15 cmc/c
0.0240964
0.0593071
0.9698932
0.0301068
105000

0.0240964
0.0464573
0.9764951
0.0235049
95000
 DESIGN CALCULATIONS
Ref SLAB MARK;- S2 Summery
Datas;-
Lx = 4m Ly = 5.2 m
fy = 415 N/Sq-mm fck = 20 N/Sq-mm
ly/lx = 1.3 <2, so slab is two way

Loadings;-
Self wt = 3.75 kN/Sq-m F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m Sunk load = 2 kN/Sq-m
Total load = 9.25 kN/Sq-m F .Load = 13.88 kN/Sq-m

Required depth;-
d = Span/(B.VxM.F) B.V = 20 (ss)
Assume 0.2 % of steel M.F = 1.6
Eff. Depth = 12.5 cm

Provided depth;-
D= 15 cm dpro = 12.5 cm

Bending moment;- Conditions; Two Adjacent Edges discontinious

Nagative moment
Page 91 ax = 0.060 Mux = 13.32 Kn-m
ratio ay = 0.047 Muy = 10.43 Kn-m
1.3 Possitive moment
case 4 ax = 0.045 Mux = 9.99 Kn-m
ay = 0.035 Muy = 7.77 Kn-m
Maximum moment = 13.32 Kn-m

Check for depth;- Computation of depth from bending

d = SQRT(Mux/.138xfckxb) 7 cm
dreq<dpro OK
Using 10 mm dia bars
Steel Reinforcement calculation;- (Required)
Using 10 mm dia bars
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Shorter direction Longer direction
Ast = 311.4 Sq-mm Ast = 221.7 Sq-mm
Ast(min) = 0.12 %bXD 180 mm2

Provided Stell Reinforcement;-

Shorter direction y 10 @ 150 mm c/c 523 Sq-mm
Ast provided ok
longer direction y 10 @ 150 mm c/c 523 Sq-mm
Ast provided ok

Check for deflection;- At the mid span,

100Ast/bD = 0.21 % M.F = 2
Actual ratio = Span/Depth 32.00
Permissible stress = B.VxM.F 40 > actual ratio, Safe

Summery of slab
Thick(cm) Reinforcement
Shorter direction Longer direction
15 Y10mm @ 15cmc/c Y10mm @ 15 cmc/c
 DESIGN CALCULATIONS
Ref SLAB MARK;- S3 Summery
Datas;-
Lx = 3.4 m Ly = 6.5 m
fy = 415 N/Sq-mm fck = 20 N/Sq-mm
ly/lx = 1.9 <2, so slab is two way

Loadings;-
Self wt = 4 kN/Sq-m F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m Sunk load = 0 kN/Sq-m
Total load = 7.5 kN/Sq-m F .Load = 11.25 kN/Sq-m

Required depth;-
d = Span/(B.VxM.F) B.V = 20 (ss)
Assume 0.2 % of steel M.F = 1.6
Eff. Depth = 10.63 cm

Provided depth;-
D= 16 cm dpro = 13.5 cm

Bending moment;- Conditions; Four Edges discontinious

Nagative moment
Page 91 ax = 0.000 Mux = 0 Kn-m
ratio ay = 0.000 Muy = 0 Kn-m
1.9 Possitive moment
case 9 ax = 0.079 Mux = 10.27 Kn-m
ay = 0.056 Muy = 7.283 Kn-m
Maximum moment = 10.27 Kn-m

Check for depth;- Computation of depth from bending

d = SQRT(Mux/.138xfckxb) 6 cm
dreq<dpro OK
Using 10 mm dia bars
Steel Reinforcement calculation;- (Required)
Using 10 mm dia bars
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Shorter direction Longer direction
Ast = 218.2 Sq-mm Ast = 141.8 Sq-mm
Ast(min) = 0.12 %bXD 192 mm2

Provided Stell Reinforcement;-

Shorter direction y 10 @ 150 mm c/c 523 mm2
Ast provided ok
longer direction y 10 @ 150 mm c/c 523 mm2
Ast provided ok

Check for deflection;- At the mid span,

100Ast/bD = 0.14 % M.F = 1.6
Actual ratio = Span/Depth 25.19
Permissible stress = B.VxM.F 32 > actual ratio, Safe

Summery of slab
Thick(cm) Reinforcement
Shorter direction Longer direction
16 Y10mm @ 15cmc/c Y10mm @ 15 cmc/c
 DESIGN CALCULATIONS
Ref SLAB MARK;- S4 Summery
Datas;-
Lx = 5m Ly = 5.6 m
fy = 415 N/Sq-mm fck = 20 N/Sq-mm
ly/lx = 1.1 <2, so slab is two way

Loadings;-
Self wt = 5 kN/Sq-m F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m Sunk load = 2.5 kN/Sq-m
Total load = 11 kN/Sq-m F .Load = 16.5 kN/Sq-m

Required depth;-
d = Span/(B.VxM.F) B.V = 20 (ss)
Assume 0.2 % of steel M.F = 1.6
Eff. Depth = 15.63 cm

Provided depth;-
D= 20 cm dpro = 17.5 cm

Bending moment;- Conditions; Three Edges discontinious

Nagative moment
Page 91 ax = 0.064 Mux = 26.4 Kn-m
ratio ay = 0.000 Muy = 0 Kn-m
1.1 Possitive moment
case 7 ax = 0.048 Mux = 19.8 Kn-m
ay = 0.043 Muy = 17.74 Kn-m
Maximum moment = 26.40 Kn-m

Check for depth;- Computation of depth from bending

d = SQRT(Mux/.138xfckxb) 10 cm
dreq<dpro OK
Using 10 mm dia bars
Steel Reinforcement calculation;- (Required)
Using 10 mm dia bars
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Shorter direction Longer direction
Ast = 441.1 Sq-mm Ast = 274.3 Sq-mm
Ast(min) = 0.12 %bXD 240 mm2

Provided Stell Reinforcement;-

Shorter direction y 10 @ 120 mm c/c 654 mm2
Ast provided ok
longer direction y 10 @ 150 mm c/c 523 mm2
Ast provided ok

Check for deflection;- At the mid span,

100Ast/bD = 0.22 % M.F = 1.6
Actual ratio = Span/Depth 28.57
Permissible stress = B.VxM.F 32 > actual ratio, Safe

Summery of slab
Thick(cm) Reinforcement
Shorter direction Longer direction
20 Y10mm @ 12cmc/c Y10mm @ 15 cmc/c
 DESIGN CALCULATIONS
Ref SLAB MARK;- S5 Summery
Datas;-
Lx = 4.6 m Ly = 8.8 m
fy = 415 N/Sq-mm fck = 20 N/Sq-mm
ly/lx = 1.9 <2, so slab is two way

Loadings;-
Self wt = 5 kN/Sq-m F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m Sunk load = 0 kN/Sq-m
Total load = 8.5 kN/Sq-m F .Load = 12.75 kN/Sq-m

Required depth;-
d = Span/(B.VxM.F) B.V = 20 (ss)
Assume 0.2 % of steel M.F = 1.6
Eff. Depth = 14.37 cm

Provided depth;-
D= 20 cm dpro = 17.5 cm

Bending moment;- Conditions; Four Edges discontinious

Nagative moment
Page 91 ax = 0.000 Mux = 0 Kn-m
ratio ay = 0.000 Muy = 0 Kn-m
1.9 Possitive moment
case 9 ax = 0.092 Mux = 24.82 Kn-m
ay = 0.056 Muy = 15.11 Kn-m
Maximum moment = 24.82 Kn-m

Check for depth;- Computation of depth from bending

d = SQRT(Mux/.138xfckxb) 9 cm
dreq<dpro OK
Using 10 mm dia bars
Steel Reinforcement calculation;- (Required)
Using 10 mm dia bars
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Shorter direction Longer direction
Ast = 413.3 Sq-mm Ast = 232.4 Sq-mm
Ast(min) = 0.12 %bXD 240 mm2

Provided Stell Reinforcement;-

Shorter direction y 10 @ 120 mm c/c 654 mm2
Ast provided ok
longer direction y 10 @ 150 mm c/c 523 mm2
Ast provided ok

Check for deflection;- At the mid span,

100Ast/bD = 0.21 % M.F = 1.6
Actual ratio = Span/Depth 26.29
Permissible stress = B.VxM.F 32 > actual ratio, Safe

Summery of slab
Thick(cm) Reinforcement
Shorter direction Longer direction
20 Y10mm @ 12cmc/c Y10mm @ 15 cmc/c
 DESIGN CALCULATIONS
Ref SLAB MARK;-S6 Summery
IS 456-2000 Lx = 4.6 Ly = 9.9
fy 415 N/mm2 fck 20 N/Sq-mm
ly/lx 2.2 >2 so slab is one way
Loadings;-
Self weight = 5.0 kN/Sq-m
Sunk load = 2.5 kN/Sq-m
F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m
Total load = 11.00 kN/Sq-m WF = 16.50 kN/Sq-m
Required depth;-
d=Span/(B.VxM.F)
Page 37 Basic value(Simplysupported)= 20
Page 38 Assume 0.2 % of steel M.F = 1.6
Effective depth (d) = 14 cm
Provided depth;-
Over all depth (D) = 20 cm
Available depth(d)= 17.5 cm
Bending moment;-
Maximum moment WLx2/8 = 43.64 Kn-m
Check for depth;-
Computation of depth from bending
d = SQRT(Mux/.138xfckxb)
13 cm dreq<dpro, OK
Assume 12 mm bars
Available depth(d) = 17.4 cm
Steel Reinforcement calculation;- (Required)
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Ast(Short) = 765 mm2
Ast(min) = 0.12 %bXD = 240 Sq-mm
Provided Stell Reinforcement;-
Shorter direction
y 12 @ 120 mm c/c 942 Sq-mm
Ast provided ok
Longer direction
y 12 @ 150 mm c/c 754 Sq-mm
Ast provided ok
Check for deflection;- (At the mid span,)
100Ast/bd = 0.44 % M.F 1.5
Actual ratio = Span/Depth = 26.44
Permissible stress = B.VxM.F
30 >actual ratio, Safe
Summery of slab
Thick(cm) Reinforcement
20 Shorter direction Longer direction
Y12 @ 12cmc/c Y12 @ 15cmc/c
 DESIGN CALCULATIONS
REF STAIR CASE TYPE;- QUARTER SPACE LANDING SUMMERY

Effective span
Assume 20cm bearing of the landing in the walls
Effective span of flight (AB)= 4.4 m
Effective span of flight (BC)= 4.2 m
Rise R = 0.16 m
Tread T = 0.3 m

Loadings;-
Assume thick of waist slab = 0.2 m
effective depth = 180 mm
Weight of w' on slope = 5 KN/m
Dead weight of horizontal areaW=w'((sqrt R 2+T2)/T)
W = 5.67 KN/m
Self weight of tread slab= 1.5 KN/m
Finishes = 1 KN/m
Live load = 3 KN/m
Total load = 11.17 KN/m
Factored load = 16.75 KN/m

Design of waist slab;-

M = Wl2/8 40.54 KN-m

Check for depth of waist slab;-

D = SQRT((Mu)/(.138fckb))
121 mm
Dreq<Dpro, OK

Tension Reinforcement;-
Mu=0.87 fy Ast d {1-(Ast fy/fck bd)}
40535000 = -64989 Ast + 7.49 Ast2
Ast = 676.47 mm2
Ast(min) = 0.87xbxd/fy
377.3494 mm2
Provided Area of steel;-
Long span = Y 16 @ 120 mm c/c 1675 Sq-mm
Short span = Y 12 @ 150 mm c/c 754 Sq-mm
Ast provided ok

Summery;-
Slab Thick 200 mm
Long span Y 16 @ 120 mm c/c
Short span Y 12 @ 150 mm c/c
 DESIGN CALCULATIONS
Ref SLAB MARK;-S6
IS 456-2000 Lx = 1.8 Ly = 4.2
fy 415 N/mm2 fck 20 N/Sq-mm
ly/lx 2.3 >2 so slab is one way
Loadings;-
Self weight = 5.0 kN/Sq-m
Sunk load = 2.5 kN/Sq-m
F. F Load = 1.5 kN/Sq-m
Live load = 2 kN/Sq-m
Total load = 11.00 kN/Sq-m WF = 16.50 kN/Sq-m
Factored
Wall Load = 23.50 kN/m w
Required depth;-
d=Span/(B.VxM.F)
Page 37 Basic value(Simplysupported)= 20
Page 38 Assume 0.2 % of steel M.F = 1.6
Effective depth (d) = 6 cm
Provided depth;-
Over all depth (D) = 20 cm
Available depth(d)= 17.5 cm
Bending moment;-
Maximum moment WLx2/2+wl = 69.03 Kn-m
Check for depth;-
Computation of depth from bending
d = SQRT(Mux/.138xfckxb)
16 cm dreq<dpro, OK
Assume 14 mm bars
Available depth(d) = 17.3 cm
Steel Reinforcement calculation;- (Required)
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Ast(Short) = 1312 mm2
Ast(min) = 0.12 %bXD = 240 Sq-mm
Provided Stell Reinforcement;-
Shorter direction
y 14 @ 100 mm c/c 1539 Sq-mm
Ast provided ok
Longer direction
y 12 @ 150 mm c/c 754 Sq-mm
Ast provided ok
Check for deflection;- (At the mid span,)
100Ast/bd = 0.76 % M.F 1.5
 Actual ratio = Span/Depth = 10.40
Permissible stress = B.VxM.F
30 >actual ratio, Safe
Summery of slab
Thick(cm) Reinforcement
20 Shorter direction Longer direction
Y14 @ 10cmc/c Y12 @ 15cmc/c
Summery

0.0240964
0.5304855
0.6852113
0.3147887
173000

12
 DESIGN CALCULATIONS
Ref SLAB MARK;-S6
IS 456-2000 Lx = 1.8 Ly = 4.2
fy 415 N/mm2 fck 20 N/Sq-mm
ly/lx 2.3 >2 so slab is one way
Loadings;-
Self weight = 5.0 kN/Sq-m
Sunk load = 2.5 kN/Sq-m
F. F Load = 1.5 kN/Sq-m
Live load = 3 kN/Sq-m
Total load = 12.00 kN/Sq-m WF = 18.00 kN/Sq-m
Factored
Wall Load = 8.20 kN/m w
Required depth;-
d=Span/(B.VxM.F)
Page 37 Basic value(Simplysupported)= 20
Page 38 Assume 0.2 % of steel M.F = 1.6
Effective depth (d) = 6 cm
Provided depth;-
Over all depth (D) = 20 cm
Available depth(d)= 17.5 cm
Bending moment;-
Maximum moment WLx2/2+wl = 43.92 Kn-m
Check for depth;-
Computation of depth from bending
d = SQRT(Mux/.138xfckxb)
13 cm dreq<dpro, OK
Assume 14 mm bars
Available depth(d) = 17.3 cm
Steel Reinforcement calculation;- (Required)
Ast = 0.5xfck/fy{1-sqrt1-(4.6XMu/fckbd2)}bd
Ast(Short) = 776 mm2
Ast(min) = 0.12 %bXD = 240 Sq-mm
Provided Stell Reinforcement;-
Shorter direction
y 14 @ 150 mm c/c 1026 Sq-mm
Ast provided ok
Longer direction
y 12 @ 150 mm c/c 754 Sq-mm
Ast provided ok
Check for deflection;- (At the mid span,)
100Ast/bd = 0.45 % M.F 1.5
 Actual ratio = Span/Depth = 10.40
Permissible stress = B.VxM.F
30 >actual ratio, Safe
Summery of slab
Thick(cm) Reinforcement
20 Shorter direction Longer direction
Y14 @ 15cmc/c Y12 @ 15cmc/c
Summery

0.0240964
0.3375188
0.8139295
0.1860705
173000

12