Scribd
Upload
41 views4 pages

Defection calculation

This document outlines the method for calculating maximum deflection of a fixed beam under various loading conditions, including point loads and uniformly distributed loads. It provides key parameters, relevant formulas, and a step-by-step calculation procedure, alongside an example calculation for a specific case. The document emphasizes the importance of verifying results against allowable limits and suggests using advanced methods for complex loading scenarios.

Uploaded by

ajaytanabcdefg
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
41 views4 pages

Defection calculation

This document outlines the method for calculating maximum deflection of a fixed beam under various loading conditions, including point loads and uniformly distributed loads. It provides key parameters, relevant formulas, and a step-by-step calculation procedure, alongside an example calculation for a specific case. The document emphasizes the importance of verifying results against allowable limits and suggests using advanced methods for complex loading scenarios.

Uploaded by

ajaytanabcdefg
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Calculating Deflection for a Fixed Beam

## 1. Introduction

A fixed beam is a structural element restrained at both ends, preventing rotation and vertical
displacement. Deflection refers to the vertical displacement of the beam under applied loads. This
document provides a method to calculate the maximum deflection for a fixed beam under common
loading conditions.

## 2. Assumptions

- The beam is made of a homogeneous, isotropic, linear elastic material.

- The beam has a constant cross-section and material properties (Young’s modulus \( E \), moment of
inertia \( I \)).

- Loads are applied in the plane of symmetry, causing deflection in the vertical direction.

- Small deflection theory applies (deflections are small compared to the beam’s length).

## 3. Key Parameters

- \( L \): Length of the beam (m)

- \( E \): Young’s modulus of the material (Pa or N/m²)

- \( I \): Moment of inertia of the beam’s cross-section (m⁴)

- \( w \): Uniformly distributed load (N/m)

- \( P \): Point load (N)

- \( \delta \): Deflection (m), positive downward

- \( a \): Distance from the left support to the point load (m)

## 4. Deflection Formulas

The deflection of a fixed beam depends on the type and location of the load. Below are the formulas
for maximum deflection for common cases, derived from structural mechanics.

### Case 1: Point Load at Midspan (\( a = L/2 \))

For a point load \( P \) applied at the center of the beam:

\[

\delta_{\text{max}} = \frac{P L^3}{192 E I}

\]
- Location: At midspan (\( x = L/2 \)).

- Note: The deflection is maximum at the point of load application.

### Case 2: Uniformly Distributed Load

For a uniformly distributed load \( w \) over the entire length:

\[

\delta_{\text{max}} = \frac{w L^4}{384 E I}

\]

- Location: At midspan (\( x = L/2 \)).

- Note: This assumes the load is evenly distributed across the beam.

### Case 3: Point Load at Arbitrary Position

For a point load \( P \) applied at distance \( a \) from the left support:

\[

\delta_{\text{max}} = \frac{P a^2 (L - a)^2}{3 E I L}

\]

- Location: At the point of load application (\( x = a \)).

- Note: This is more complex and requires specifying \( a \). For \( a = L/2 \), it simplifies to Case 1.

## 5. Step-by-Step Calculation Procedure

1. **Identify the Loading Condition**: Determine whether the beam is subjected to a point load,
uniformly distributed load, or a combination.

2. **Gather Beam Properties**:

- Measure or obtain \( L \), \( E \), and \( I \).

- For \( I \), use the moment of inertia formula for the cross-section (e.g., for a rectangular section,
\( I = \frac{b h^3}{12} \), where \( b \) is the width and \( h \) is the height).

3. **Select the Appropriate Formula**: Based on the load type, choose the relevant deflection
formula from Section 4.

4. **Input Values**: Substitute the known values (\( P \), \( w \), \( L \), \( E \), \( I \), \( a \)) into the
formula.

5. **Calculate Deflection**: Compute \( \delta_{\text{max}} \) using the formula. Ensure units are
consistent (e.g., convert all lengths to meters, forces to Newtons).
6. **Verify Results**: Check the deflection magnitude against allowable limits (e.g., \(
\delta_{\text{max}} < L/360 \) for typical building codes) and ensure calculations align with expected
behavior.

## 6. Example Calculation

### Problem

A fixed steel beam has:

- Length \( L = 4 \, \text{m} \)

- Young’s modulus \( E = 200 \, \text{GPa} = 200 \times 10^9 \, \text{Pa} \)

- Moment of inertia \( I = 1.2 \times 10^{-5} \, \text{m}^4 \) (rectangular section, \( b = 0.1 \, \text{m}
\), \( h = 0.2 \, \text{m} \))

- Uniformly distributed load \( w = 10 \, \text{kN/m} = 10,000 \, \text{N/m} \)

Calculate the maximum deflection.

### Solution

1. **Identify Loading**: Uniformly distributed load.

2. **Formula**: Use \( \delta_{\text{max}} = \frac{w L^4}{384 E I} \).

3. **Input Values**:

- \( w = 10,000 \, \text{N/m} \)

- \( L = 4 \, \text{m} \)

- \( E = 200 \times 10^9 \, \text{Pa} \)

- \( I = 1.2 \times 10^{-5} \, \text{m}^4 \)

4. **Calculate**:

\[

L^4 = 4^4 = 256 \, \text{m}^4

\]

\[

E I = (200 \times 10^9) \times (1.2 \times 10^{-5}) = 2.4 \times 10^6 \, \text{N·m}^2

\]

\[

\delta_{\text{max}} = \frac{10,000 \times 256}{384 \times 2.4 \times 10^6}


\]

\[

= \frac{2,560,000}{921,600,000} \approx 0.00278 \, \text{m} = 2.78 \, \text{mm}

\]

5. **Verify**: \( \delta_{\text{max}} = 2.78 \, \text{mm} \) is reasonable for a steel beam. Compare


with \( L/360 = 4000/360 \approx 11.11 \, \text{mm} \), which is satisfied.

### Answer

The maximum deflection is approximately **2.78 mm** at midspan.

## 7. Notes

- For complex loading (e.g., multiple point loads or partial distributed loads), use superposition by
calculating deflections for each load separately and summing them.

- If the beam’s cross-section varies or the material is non-linear, advanced methods (e.g., finite
element analysis) may be required.

- Always verify results with structural engineering software or hand calculations for critical
applications.

- For real-time data or additional resources, consider searching engineering databases or standards
(e.g., AISC, Eurocode).

## 8. References

- Timoshenko, S., & Gere, J. M. (1972). *Mechanics of Materials*.

- Hibbeler, R. C. (2017). *Structural Analysis*.

- Relevant standards: AISC Steel Construction Manual, Eurocode 3.

---

This document provides a clear, actionable guide for calculating fixed beam deflection. If you need a
specific format (e.g., PDF, LaTeX) or additional details (e.g., shear force diagrams, slope calculations),
let me know!

You might also like