REPUBLIC OF THE PHILIPPINES

DEPARTMENT OF PUBLIC WORKS

TABLE OF CONTENT AND HIGHWAYS

ARCHITECTURAL
LAND USE AND ZONING
A1 PERSPECTIVE
SITE DEVELOPMENT
VICINITY MAP

A2 GROUND FLOOR PLAN

SECOND FLOOR PLAN

A3 FRONT ELEVATION
REAR ELEVATION
RIGHT SIDE ELEVATION LINE AND GRADE
LEFT SIDE ELEVATION

A4 LONGITUDINAL
CROSS SECTION A-A
SECTION B-B
SCHEDULE OF DOORS
AND WINDOWS

A5 REFLECTED CEILING PLAN

STEEL RAILING DETAIL
STEEL STAIR DETAIL
FIRE SAFETY

STRUCTURAL

S1 FOUNDATION PLAN
PERSPECTIVE CONCRETE BEAM LAYOUT

ARCHITECTURAL
S2 CONCRETE BEAM/SLAB LAYOUT
BEAM SCHEDULE
TYPICAL CONNECTION DETAIL
LEGENDS/ NOTES

S3 COLUMN FOOTING DETAIL

SLAB DETAIL
WALL FOOTING DETAIL
STRUCTURAL
S4 GENERAL STRUCTURAL NOTES

PLUMBING

P1 PLUMBING LAYOUT PLAN

ISOMETRIC LAYOUT
SEPTIC VAULT DETAIL SANITARY
NOTES AND SPECIFICATION

ELECTRICAL

E1 LIGHTING AND POWER LAYOUT

PLAN (GROUND/SECOND LEVEL)
SCHEDULE OF LOADS
SINGLE LINE DIAGRAM
LOAD COMPUTATION
VOLTAGE DROP COMPUTATION ELECTRICAL
ONE LINE DIAGRAM

1 SITE DEVELOPMENT PLAN 2 VICINITY MAP

SCALE 1: 100m
A-1 SCALE DNTS
A-1
MECHANICAL
PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREY
SHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: A
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 1 5
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
NOTE:
FF-1 (FLOOR FINISH) - 60cm x 6cm GRANITE TILES

CR TILES:
(FLOOR FINISH) - 60cm x 60cm GRANITE TILES
w/ WALL TILES 300mm x 600mm
CERAMIC TILES

B B
1 2 3 1 2 3

7.50 7.50

3.25 4.25 3.33 4.17

2.00 1.25

SERVICE AREA

W-2 W-2
S S

A A STEEL RAILINGS
REF SINK RANGE

STEEL RAILINGS
BEDROOM-2
2.10

FF-1
60cm x 60cm
KITCHEN AREA

PLANT BOX
FF-1
60cm x 60cm D-2

4.10

4.10
D-2
TOILET / BATH W-2
D-3
1.50

5.80
FF-2
W-2 LANDING
40cm x 40cm
DINING AREA
FF-1
60cm x 60cm
7.00

7.00

7.04
ROOF DECK
D-2
B B (OPEN AREA)
FF-1
60cm x 60cm

LIVING AREA
A A

STEEL RAILINGS
FF-1

PLANT BOX
1.70
60cm x 60cm
W-2
3.40

S
BEDROOM-1
FF-1
60cm x 60cm S S

C C

1.24
S

D-1
W-2 W-3 W-3
S

D D STEEL RAILINGS
S S

W-1

3.25 4.25 3.33 4.17

7.50 7.50

GROUND FLOOR
ROOF DECK
1 FLOOR PLAN
A-2 SCALE 1:100m 2 FLOOR PLAN
A-2 SCALE 1:100m

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: A
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 2 5
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 SYNTHETIC STONE
WALL DECO DESIGN MOLDING

1 2 3 STEEL RAILINGS D C B A
SQUARE TUBULAR 1 1/2" X 2" FRAME

STEEL STAIR
SLIDING WINDOW
(SEE SCHEDULE)

APEX-LINE APEX-LINE
1.25

1.15
SECOND_LEVEL SECOND_LEVEL
4.45

SLIDING PANEL DOOR

3.00

(SEE SCHEDULE)
3.20

3.20
AWG AWG

S S S S

2.30
S

FINISH_FLOOR_LINE FINISH_FLOOR_LINE
0.20

0.20
NAT.GRADE_LINE NAT.GRADE_LINE

1 FRONT ELEVATION 2 RIGHT SIDE ELEVATION

A-3 SCALE 1:100m A-3 SCALE 1:100m

STEEL RAILINGS
SQUARE TUBULAR 1 1/2" X 2" FRAME
AWNING GLASS

A B C D 3 2 1

AWNING GLASS SLIDING WINDOW SLIDING WINDOW

(SEE SCHEDULE) (SEE SCHEDULE)

APEX-LINE APEX-LINE
1.25

1.25
CHB 4" THK
SECOND_LEVEL WALL
SECOND_LEVEL

CHB 4" THK

4.45

4.45
WALL
AWG AWG AWG
3.20

3.20
S S S S

FINISH_FLOOR_LINE FINISH_FLOOR_LINE

NAT.GRADE_LINE NAT.GRADE_LINE

4 LEFT SIDE ELEVATION 3 REAR ELEVATION

A-3 SCALE 1:100m A-3 SCALE 1:100m

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: A
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 3 5
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 STEEL RAILINGS
SQUARE TUBULAR 1 1/2" X 2" FRAME

1 2 3 D C B A

APEX-LINE APEX-LINE
1.25

1.25
ROOF DECK ROOF DECK
AREA AREA
SECOND_LEVEL SECOND_LEVEL

0.90
4.45

3.00
3.20

3.20
2.30
LIVING LIVING KITCHEN
AREA AREA AREA
FINISH_FLOOR_LINE FINISH_FLOOR_LINE
0.20

0.20
NAT.GRADE_LINE NAT.GRADE_LINE

1 CROSS SECTION THRU A-A 2 LONGITUDINAL SECTION THRU B-B

A-4 SCALE 1:100m A-4 SCALE 1:100m

0.90 0.80 0.75 1.95 1.00 1.00 0.40 1.00 0.70

0.50

0.50
AWG AWG AWG AWG
AWG
1.60

1.60

1.60

1.60
S S S S AWG
2.10
2.10

2.10

2.10

2.10

2.10
S S

1.60

1.60
FIXED
AWG

0.50
FIN_FLR_LINE FIN_FLR_LN

D D D W W W W W W
1 2 1 1 2 3 4 5 6
3 UNIT 2 UNIT 1 UNIT 1 UNIT
1 UNIT 1 UNITS
1 UNITS 3 UNITS 1 UNIT GLASS WINDOW GLASS AWNING GLASS AWNING GLASS AWNING WINDOW
GLASS WINDOW AWNING
SLIDING PANEL DOOR PANEL DOOR PVC DOOR IN ALUM. FRAME WINDOW WINDOW IN ALUM. FRAME
IN ALUM. FRAME
IN ALUM. FRAME IN ALUM. FRAME
BEDROOM, BEDROOM 1,2 , KITCHEN T&B
LIVING / ENTRY T&B BEDROOM 1 LIVING DINING/KITCHEN
KITCHEN LIVING

3 SCHEDULE OF DOORS AND WINDOWS

A-4 SCALE 1: 100m

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: A
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 4 5
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 0.83

1 2 3 .83
R0

0.85
LANDING
Ø1.66
7.50

3.25 4.25

2.00 1.25

0.86 0.83
A
2.10

CH=2.90 M
PLYWOOD 5mm
TUBULAR STEEL
1" X 1"

1.20
RAILINGS ROOF DECK
CH=2.90 M
1.50

5.80
PLYWOOD 5mm CH=2.90 M
PLYWOOD 5mm
7.00

0.26 0.26 0.26 0.25 0.26 0.26 0.26

B 1" X 1" TUBULAR STEEL
1 21" X 2" TUBULAR STEEL

0.26 0.26 0.26 0.26 0.26 0.26 0.26

SPACING @ 0.75 M.
G.I PIPE 4" DIAMETER
± 2.00 (POLE)
CH=2.90 M
3.40

PLYWOOD 5mm
C
1.90

CH=2.90 M

3.20
D SPANDREL

1.15
3.25 4.25
10MM STEEL PLATE
7.50 ATTACHED TO GROUND

1 REFLECTED CEILING LAYOUT

A-5 SCALE 1:100m

3 STEEL STAIR DETAIL

A-5
2 STEEL RAILINGS SCALE 1:50m

A-5 SCALE 1: 25m

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING DATE REMARKS

PLACE ISSUED ENGINEER as such must not be

reproduced or copied in part or in whole
LOCATION: CHECK BY: A
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 5 5
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 1 2 3 1 2 3

7.50 7.50
SLAB ON FILL,
ELEV @ 0.25 M 3.25 4.25 3.25 4.25
T= 100 MM
W/ 1OMM RSB S.P @ 2.00 1.25 2.12 2.12
400 MM

F2-C2 F1-C1 F2-C2

WF-2 WF-2 B1 B1
A A
2.10

TB-1

WF-2

3.60
B1 B1
WF-2

WF-1 B2

4.10
B2
WF-2
1.50

5.80
WF-1

B2 B2

F1-C1
B2
F1-C1

F1-C1

WF-1
7.00

7.04
7.00
B TB-1 B
TB-1

WF-2
TB-1

B2 B1

2.20
WF-2

WF-2

B1 B2

1.70
3.40

F2-C2
F2-C2

C F2-C2 C
WF-2 B1 B1 B1

1.24

1.28
CB-1 B2 CB-1
WF-2

WF-1

D D
WF-2 WF-1 B3 B3
F1-C1

3.25 4.25 3.33 4.17

7.50 7.50

1 FOUNDATION PLAN 3 CONCRETE BEAM PLAN

S-1 SCALE 1:100m
S-1 SCALE 1:100m

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING DATE REMARKS

PLACE ISSUED ENGINEER as such must not be

reproduced or copied in part or in whole
LOCATION: CHECK BY: S
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 1 4
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 CONCRETE POST
1 2 3
(OUTSIDE WALLING)
10mm Ø DRB DOWEL
TO MATCH CHB HOR. BARS

(INTERIOR SIDE) DOWEL DOWEL

7.50

3.25 4.25 COT. L - SHAPED 10mm Ø DRB DOWEL

TO MATCH CHB HOR. BARS

2.12 2.12
SEE SCHEDULE OF CHB REINFORCEMENT (b) INTERSECTING R.C. COLUMN OR WALL
FOR SIZE AND SPACING OF REBARS

CHB WALL

A TYP. CONNECTION DETAIL OF CONCRETE

2 MASONRY UNITS AT COLUMN AND/OR WALLS
(a) CORNER WALL S-2 D R A W N N O T S C A L E

3.03
3.60

SB-1 SB-1
SB-1
BEAM SCHEDULE
7.00

7.00
B BEAM - 1 BEAM - 2 BEAM - 3 TIE BEAM - 1 ROOF BEAM CANTILIVER

2.62
2.20

SB-1 SB-1 SB-1

TOP TOP TOP TOP
TOP TOP

300
350

300

300
C

250
250
1.35
BOTTOM
1.28

SB-2 SB-2 SB-2 BOTTOM BOTTOM BOTTOM BOT. BOT.

200
D 200 200 200 150 200

main bar: main bar: main bar:

main bar: main bar: main bar:
3-16mm∅ 3-16mm∅ 3-16mm∅
3.25 4.25 2-16mm∅ 2-16mm∅ 2-16mm∅
4-16mm∅ 4-12mm∅ 5-16mm∅
ties: ties: ties:
ties: ties: ties:
1omm∅ 1omm∅ 1omm∅
7.50 1omm∅ 1omm∅ 1omm∅
sp @ 4-5omm,
sp @ 4-5omm, sp @ 4-5omm, sp @ 4-5omm, sp @ 4-5omm, sp @ 4-5omm,
4-1oomm, 4-1oomm, 4-1oomm,
4-1oomm, 4-1oomm, 4-1oomm,
4-15omm rest 4-15omm rest 4-15omm rest
4-15omm rest 4-15omm rest 4-15omm rest
@ 2oo mm o.c @ 2oo mm o.c @ 2oo mm o.c
1 CONC. BEAM/SLAB LAYOUT @ 2oo mm o.c @ 2oo mm o.c @ 2oo mm o.c
S-2 SCALE 1:100m

NOTESONRENIFORCNIGSTEELBARS: 2. ALL CONCRETE RENIFORCEMENT SHALL BE DETALIED, FABRC I ATED,

LABELED, SUPPORTED AND SPACED NI FORMS, SECURED NI THE
.1 ALL RENIFORCNIG STEEL BARS SHALL BE NEW BLILET, HOT ROLLED, REQUR
I ED LOCATO IN NI ACCORDANCE WTIH THE PROCEDURES AND NOTE:
WELDABLE, DEFORMED BARS CONFORMNIG TO THE SPECFC
I ATO
I NS OF REQUR
I EMENTS OUTLNIED NI THE LATEST EDTO IN OF THE BULIDNIG CODE A. MINIMUM LAP SPLICE - 30mm
PNS492;001(ASTM65
1)WHOSEGRADESISHOWNONTABLEBELOW. AND THE MANUAL OF STANDARD PRACTCIE FOR DETALNIG RENIFORCED B. PROVIDE 1-180mm VERTICAL BAR @ CORNERS INTERSECTION END OF WALLS AND
CONCRETESTRUCTURESA
, C-I35
1. EACH SIDE
OF OPENING.
TABLE 1 3. ALL RENIFORCNIG BARS SHALL BE CLEANED THOROUGHLY OF ALL C. WHERE CHB WALLS ADJOIN COLUMNS RC BEAMS & WALLS DOWELS WITH THE SAME
GRADE BARS LOOSE RUST, SOLI OR OTHER MATERA
IL M
I MEDA
I TELY PROI R TO PLACNIG SIZE
CONCRETE. AS VERTICAL OR HORIZONTAL REINFORCEMENT SHALL BE PROVIDED.
GRADE 33 D. LINTEL SHALL BEAR AT LEAST 18 INCHES (400mm) ON EACH SIDE OF MASONRY
10mm∅ & 12mm∅
(fy = 227.5 MPa) WALL
4. PROVD
I EFORMSFORFOOTNIGTEIBEAM.
OPENINGS.
GRADE 33
16mm∅ & LARGER E. PROVIDE POST AND LINTEL BEAM @3000mm O.C.
(fy = 227.5 MPa) 5. KNIDLYFOLLOWSCHEDULESORBETTERREFERTOENGNIEER.

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: S
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 2 4
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 0.45 0.50
10mm DIA COLUMN 10mm DIA COLUMN 10mm dia. VERTICAL
6-16mm DIA. , 2-12mm DIA 4-16mm DIA. VERTICAL 10mm dia. VERTICAL 4" CONCRETE 4" CONCRETE
TIES, SP. @ 4-50mm, TIES, SP. @ 4-50mm, DEF. BARS
VERTICAL REINF. BARS REINF. BARS DEF. BARS HOLLOW BLOCK HOLLOW BLOCK
4-100mm, 4-150mm, 4-100mm, 4-150mm, SP. @ 600mm ON
REST @ 200mm O.C. REST @ 200mm O.C. SP. @ 600mm ON
10mm dia. CENTER 10mm dia.
CENTER
6-16mm DIA. , 2-12mm DIA 4-16mm DIA. VERTICAL TRANSVERSE REINF. TRANSVERSE REINF.
VERTICAL REINF. BARS REINF. BARS BARS BARS
10mm dia. COLUMN TIES SP. @ 10mm dia. COLUMN TIES SP. @ SP. @ 400mm ON SP. @ 400mm ON
4-50mm, 4-100mm, 4-150, REST @ 4-50mm, 4-100mm, 4-150, REST @ CENTER CENTER
3 - 10mm dia. 3 - 10mm dia.
200mm O.C. 200mm O.C. LONGITUDINAL
LONGITUDINAL
REINF. BARS SP. AS REINF. BARS SP. AS
7-16mm DIA. SHOWN SHOWN
7-16mm DIA. REINF. REINF.
BEDBARS PLAN

1.20

1.20
BEDBARS PLAN
SP AS SHOWN BW. SP AS SHOWN
4" CONCRETE 3
4" CONCRETE
BW. 3 10mm dia. VERTICAL
10mm dia. VERTICAL HOLLOW BLOCK HOLLOW BLOCK

0.30

0.30
DEF. BARS DEF. BARS
100mm THK. 100mm THK. SP. @ 600mm ON SP. @ 600mm ON 10mm dia.
10mm dia.
COMPACTED GRAVEL COMPACTED GRAVEL CENTER CENTER HORIZONTAL DEF.
HORIZONTAL DEF.
BARS SP. @ EVERY 3 BARS SP. @ EVERY 3
LAYERS OF CHB LAYERS OF CHB
NATURAL GROUND LINE
NATURAL GROUND LINE

10mm dia. 10mm dia.

0.35 EQ

EQ 0.30 EQ
TRANSVERSE REINF. TRANSVERSE REINF.

0.60
0.40
BARS BARS
1.20

1.10
SP. @ 400mm ON SP. @ 400mm ON

0.25
C1 C1

0.25
CENTER CENTER
7-16mm DIA. 7-16mm DIA.
REINF. BEDBARS REINF. BEDBARS
EQ

SP AS SHOWN BW. SP AS SHOWN BW. 3 - 10mm dia. 3 - 10mm dia.

100mm THK. LONGITUDINAL SECTION 100mm THK.
PLAN PLAN LONGITUDINAL SECTION
COMPACTED REINF. BARS SP. AS COMPACTED
REINF. BARS SP. AS 0.45 0.50 GRAVEL BASE
1.20 1.10 SHOWN GRAVEL BASE SHOWN

3 WF- 1 DETAIL 4 WF- 2 DETAIL

1 C1-F1 DETAIL 2 C2-F2 DETAIL S-3 SCALE 1: 25m S-3 SCALE 1: 25m

S-3 SCALE 1: 30m S-3 SCALE 1: 30m

12MM ∅ DEFORMED BAR S.P

@ 2OO MM VERT. & HOR.

12MM ∅ DEFORMED BAR S.P @ 2OO MM VERT. & HOR. 0.25 1.28 0.15
0.25 3.25 0.25 4.25 0.25
0.32 0.64 0.32
0.81 1.63 0.81 1.00 2.25 1.00 TOP BARS TOP BARS

SLAB THICKNESS
TOP BARS TOP BARS TOP BARS TOP BARS L / 4 L / 4

THICKNESS
L / 4 L / 4 L / 4 L / 4

0.12

SLAB
0.12
L / 8 L / 8 L / 8 L / 8
0.40 2.45 0.40 0.53 3.02 0.53 L / 8 L / 8
BOTTOM BARS BOTTOM BARS
0.16 0.96 0.16
BOTTOM BARS
5 SLAB-1 DETAIL
S-3 SCALE 1: 30m 6 SLAB-2 DETAIL
S-3 SCALE 1: 30m

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: S
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE
T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 GENERAL STRUCTURAL NOTES
GENERAL NOTES
TYPICAL BAR BENDING AND CUTTING DETAILS FOR SLABS NOTES ON COLUMNS
1.0 STANDARDS AND REFERENCES
3. IF SLABS ARE REINFORCED BOTHWAYS BARS ALONG THE SHORTER SPAN SHALL BE PLACED BELOW 1. PROVIDE EXTRA SETS OF TIES AT 100mm O.C. FOR TIED COLUMN REINFORCEMENT ABOVE AND BELOW
TABLE 'A'
TENSION BARS
TABLE 'A'
COMPRESSION BARS
NOTES OF STIRRUPS
THE FOLLOWING SHALL GOVERN THE DESIGN, FABRICATION AND CONSTRUCTION OF THE PROJECT.
THOSE ALONG THE LONG SPAN AT THE CENTER AND OVER THE LONGER SPAN FOR REINFORCING BARS BEAM-COLUMN CONNECTIONS FOR A DISTANCE FROM FACE OF CONNECTION EQUAL TO THE GREATER EMBEDMENT LENGTHS AND EMBEDMENT LENGTHS AND 1. ALL REINFORCEMENT SHALL BE BENT COLD UNLESS OTHERWISE PERMITTED BY THE STRUCTURAL
1.1 NATIONAL STRUCTURAL CODE OF THE PHILIPPINES (N.S.C.P) VOL. 1, 6TH EDITION 2015. NEAR THE SUPPORTS. THE SPACING OF THE BARS AT THE COLUMN STRIPS SHALL NOT BE MORE THAN OF THE OVERALL THICKNESS OF COLUMN, 1 /6 THE CLEAR HEIGHT OF COLUMN OR 450mm. LAPPED SPLICED IN MILLIMETERS LAPPED SPLICED IN MILLIMETERS ENGINEER.
ONE AND HALF (1 1/2) SLAB THICKNESS.
2.0 DESIGN CRITERIA 2. COLUMN TIES SHALL BE PROTECTED EVERYWHERE BY A COVERING OF CONCRETE CAST BAR SIZE fc' = 20.7MPa(3000psi) fc' = 27.6MPa(4000psi) BAR SIZE fc' = 20.7MPa(3000psi) fc' = 27.6MPa(4000psi)
2.1 LOADINGS 4. TEMPERATURE BARS FOR SLAB SHALL BE GENERALLY PLACED NEAR THE FACE IN TENSION AND SHALL MONOLITHICALLY WITH THE CORE WITH THE MINIMUM THICKNESS OF 40mm AND NOT LESS THAN 40 (DEFORMED) EMBEDMENT (DEFORMED) EMBEDMENT 2. AS SHOWN IN THE DESIGN DRAWINGS OR PERMITTED BY THE STRUCTURAL ENGINEER.
LAPPED EMBEDMENT LAPPED LAPPED EMBEDMENT LAPPED
NOT BE LESS THAN 0.0020 X GROSS CROSS-SECTIONAL AREA (Ag) OF THE SLAB (SEE SCHEDULE BELOW). TIMES THE MAXIMUM SIZE OF COARSE AGGREGATE IN MILLIMETERS.
A. DEAD LOAD 10mm Ø 300 300 300 300 10mm Ø 225 300 200 300 TIES & CLOSE STIRRUPS MUST BE BENT AT 135°.
CONCRETE 3. WHERE COLUMNS CHANGE IN SIZE, VERTICAL REINFORCEMENTS SHALL BE OFFSET AT A SLOPE OF NOT
23.56 kN/m SCHEDULE OF MINIMUM SLAB REINFORCEMENT MORE THAN 1 IN 6 AND EXTRA 10mm TIES AT 100mm SHALL BE PROVIDED THRU OUT THE OFFSET 12mm Ø 300 300 300 300 12mm Ø 275 300 250 300
STEEL 76.93 kN/m THICKNESS MINIMUM TEMPERATURE BARS REGION. 16mm Ø 300 400 300 400 16mm Ø 350 400 325 400
150mm THK. CHB WALL 2.73 kPa 100mm 10 mm Ø @ 390mm EACH WAY
125mm 10 mm Ø @ 300mm EACH WAY 4. UNLESS OTHERWISE INDICATED IN THE PLANS, LAP SPLICES FOR VERTICAL COLUMN REINFORCEMENT 20mm Ø 400 550 350 500 20mm Ø 450 500 475 500
100mm THK. CHB WALL 2.11 kPa
150mm 10 mm Ø @ 250mm EACH WAY SHALL BE MADE WITHIN THE CENTER HALF OF COLUMN HEIGHT AND THE SPLICE LENGTH SHALL NOT BE 25mm Ø 600 800 550 750 25mm Ø 550 625 550 625
B. LIVE LOAD 175mm 10 mm Ø @ 200mm EACH WAY LESS THAN 40 BAR DIAMETERS. WELDING OR APPROVED MECHANICAL DEVICES MAY BE USED
MANUFACTURING 200mm 10 mm Ø @ 150mm EACH WAY PROVIDED THAT NOT MORE THAN ALTERNATE BARS ARE WELDED OR MECHANICALLY SPLICED AT ANY 28mm Ø 750 1000 650 850 28mm Ø 625 675 625 675
LIGHT 6.0 KpA LEVEL AND THE VERTICAL DISTANCES BETWEEN THESE WELDS OR SPLICES OF ADJACENT BARS IS NOT 32mm Ø 950 1300 850 1100 32mm Ø 700 775 700 775
CONSTRUCTION 1.0 KpA
5. UNLESS OTHERWISE NOTED IN THE PLANS ALL BEDDED SLABS SHALL BE REINFORCED WITH 10mm Ø AT LESS THAN 600mm. 180° END HOOKS
250mm O.C. EACH WAY TO CENTER OF SLAB AND CONSTRUCTION JOINTS FOR THE SAME SHALL NOT BE NOTE: TOP PLAIN BARS, MULTIPLY VALUE BY 2 NOTE: TOP PLAIN BARS, MULTIPLY VALUE BY 2
ROOF CROSS - TIE
1.0 kPa LESS THAN 3.65 METERS APART. VALUES GIVEN ABOVE CAN ALSO BE USED
FOR COLUMNS.
6. PROVIDE EXTRA REINFORCEMENTS FOR CORNER SLAB (TWO ADJACENT DISCONTINUOUS EDGES) AS
C. WIND LOAD (NSCP 2010) SHOWN BELOW. 3. IF THE BEAM REINFORCING BARS END IN A WALL THE CLEAR DISTANCE FROM THE BAR TO THE FARTHER
BASIC WIND VELOCITY, V = 300 KPH 7. CONCRETE SLAB REINFORCEMENTS SHALL BE PROPERLY SUPPORTED WITH 10mm Ø STEEL CHAIR OR FACE OF THE WALL NOT BE LESS THAN 25mm. EMBEDMENT LENGTH SHALL BE AS SHOWN IN A TABLE 'A' FOR
APPROVED EQUIVALENT SPACED AT 1.0 METER ON CENTER BOTHWAYS. TENSION BARS AND TABLE 'B' FOR COMPRESSION BARS UNLESS SPECIFIED IN PLAN. TOP BAR SHALL NOT BE
P = qh [(GCpf)-(GCpi)], DESIGN WIND PRESSURE SPLICED WITHIN THE COLUMN OR WITHIN A DISTANCE TWICE THE MEMBER DEPTH FORM THE FACE OF THE
WHERE: qh = VELOCITY PRESSURE, kPa A COLUMN. AT LEAST TWO STIRRUPS SHALL BE PROVIDED AT ALL SPLICES. 90° END HOOKS
GCpf = EXTERNAL PRESSURE COEFFICIENT 4. IF THERE ARE TWO OR MORE LAYERS OF REINFORCING BARS, USE 25mmØ BAR SEPARATORS SPACED AT 1.0M
GCpi = INTERNAL PRESSURE COEFFICIENT Ø12x1000 LONG AT ON CENTER. IN NO CASE SHALL THERE BE LESS THAN ONE (1) SEPARATORS BETWEEN TWO LAYERS OF BARS.
D. SEISMIC LOAD (NSCP 2010) MID-DEPTH OF SLAB
AT EACH CORNER 5. MINIMUM CONCRETE PROTECTION FOR REINFORCING BARS OR STEEL SHAPES SHALL BE AS SHOWN IN FIG. MAIN BAR END HOOKS
V = Cv I
RT W DESIGN BASE SHEAR B-2 UNLESS SPECIFIED ELSEWHERE. (ALL GRADES)

CONF. REINF.
1-Ø12 TOP & JOINT HOOP SPACE @ " 2Sh" WHEN THERE
BOTT. BARS ARE BEAMS HAVING WIDTH OF AT LEAST 180° HOOK 90° HOOK
Vmax = 2.50R CaI W Vmin = 0.11 CaIW BAR SIZE DIAMETER
ONE-HALF THE COLUMN WIDTH & DEPTHS (DEFORMED) (mm)
1-Ø12 EA. NOT LESS THAH FRAME INTO FOUR SIDES OF D+2db L L
Vmax = 0.80RZNvI W (ZONE 4) TOP & BOTT. THE COLUMN. ALL OTHER CONDITIONS USE 10mm Ø 60 75 125 150
WHERE: W = TOTAL DEAD LOAD HOOPS @ " Sh" CENTERS.
12mm Ø 75 100 150 200
T = NATURAL PERIOD = Ct(hn)2/3 38mm 95 125 175 250
SLAB 16mm Ø
WHERE: C = NUMERICAL COEFFICIENT CLEAR

CONF. REINF.
OPENING MAIN REINFORCEMENTS 20mm Ø 115 150 200 300
h = BUILDING HEIGHT
I = IMPORTANCE FACTOR = 1.00 25mm Ø 150 200 230 450
WEB BARS
R = NUMERICAL FACTOR = 8.50 1-Ø12 EA. SEE NOTE 28mm Ø 240 300 350 550
SEISMIC COEFFICIENT Cv = 0.44Nv TOP & BOTT. SLEEVE FOR UTILITY
SEE NOTE 32mm Ø 300 200 450 600
Ca = 0.64Nv PIPES MAX 1/5D
IN TWO WAY SLAB EXTEND SECTION "A" FOR COL. BAR SPLICES SEE TABLE OF
NEAR SOURCE FACTOR ( 10km ) Nv = 1.6 BARS UP TO BEAM SUPPORT MIN. LAP SPLICE LENGTH OF COLUMN
Na = 1.2 REINFORCEMENT ( SPACING OF TIES 25mm Ø
OMIT TRIMMER BARS WHERE PROVIDE 3-10mmØ EXTRA
ALONG THIS REGION SHALL NOT BE SEE NOTE SEPARATOR
Z = SEISMIC ZONE = 0.40 ( ZONE 4 ) OPENING IS FRAMED BY BEAM STIRR. EACH SIDE SLEEVES
LESS THAN 100mm)
TYPICAL SLAB

CONF. REINF.
S = SOIL TYPE = C
TYP. DET. FOR SLEEVES 135° HOOKS
OPENING DET. NOTE 1: 20 mm CLEAR FOR JOIST
40 mm CLEAR FOR BEAMS THRU CONCRETE BEAM
2.2 DESIGN STRESSES
AND GIRDERS
A. CONCRETE FOR FOOTING, COLUMNS, BEAMS AND SLAB ON FILL NOTE:
COMPRESSIVE STRENGTH @ 28 DAYS ALL CONCRETE REINF. DETAIL SHOULD BE
B. REINFORCING STEEL BARS DONE IN ACCORDANCE WITH THE LATEST
EDITION OF ACI DETAILING MANUAL FIG. B-2
a. FOR BARS 16mmØ AND GREATER FIG. B-3

CONF. REINF.
INTERMEDIATE GRADE DEFORMED BAR
b. FOR BARS LESS THAN 16mmØ
( STRUCTURAL GRADE DEFORMED BAR )
NOTES ON CONCRETE MIXES & PLACING
6. WHEN A BEAM CROSSES A GIRDER, REST BEAM ON TOP OF GIRDER BARS, BEAM REINFORCING BAR
C. STRUCTURAL STEEL, ASTM - A36 1. ALL CONCRETE SHALL DEVELOP A MIN. COMPRESSIVE AT THE END OF TWENTY EIGHT (28) DAYS W/ SHALL BE SYMMETRICAL ABOUT CENTER LINE WHENEVER POSSIBLE.
FOR TRUSSES, BRACINGS & STRUTS CORRESPONDING MAXIMUM SIZE AGGREGATE & SLUMPS AS FOLLOWS. 7. GENERALLY NO SPLICES SHALL BE PERMITTED AT POINTS WHERE CRITICAL BENDING STRESSES OCCUR, 90° HOOKS
D. PURLINS
LOCATION 28 DAYS STRENGTH MAX. SIZE OF MAX SLUMP TYPICAL COLUMN ELEV. SHOWING SPLICES WHERE SO PERMITTED SHALL BE INDICATED IN THE TABLE 'A' AND 'B'. WELDED SPLICES SHALL
DEVELOP IN TENSION AT LEAST 125% OF THE SPECIFIED YIELD STRENGTH OF THE BAR. NOT MORE
COLD FORMED LIGHT GAGE SHAPES
E. MASONRY UNIT (CHB)
AGGREGATE DOWELS AND TIES SPACING THAN 50% OF THE BARS AT ANY ONE SECTION IS ALLOWED TO BE SPLICED THEREIN.
ALL OTHERS, INCLUDING
NON-LOAD BEARING CHB WALLS SUSPENDED SLABS, 3 000 psi (20.7 MPa) 20 mm 100 mm
F. WELDS-USED E-60xx ELECTRODE
COLUMNS 3 000 psi (20.7 MPa) 20 mm 100 mm STIRRUP AND TIE HOOKS
G. STRUCTURAL BOLTS, ASTM-A307
20 mm 100 mm (ALL GRADES)
a. Ft = 96.60 MPa ( 14,000 psi ) b. Fv = 69 MPa ( 10,000 psi )
3. IN THE INTREPRETATION OF THE DRAWING, INDICATED DIMENSIONS DHALL GOVERN AND
BEAMS, SLABS
SLAB ON FILL
3 000 psi (20.7 MPa)
2 500 psi (17.5 MPa) 20 mm 100 mm LAP SPLICE LENGTH: AT ANY
NOTES ON WELDS BAR SIZE DIAMETER 180° HOOK 90° HOOK
1. USE E70xx ELECTRODES FOR ALL MEMBERS WELDED.
DISTANCES AND SIZES SHALL NOT BE SCALED FOR CONSTRUCTION PURPOSES. LEVEL NO MORE THAN (DEFORMED) (mm) D+2db L L
2. MAINTAIN MINIMUM CONCRETE COVER FOR REINFORCING STEEL AS FOLLOWS. 2.
4. IN THE REFERENCE TO OTHER DRAWINGS, SEE ARCHITECTURAL DRAWINGS FOR DEPRESSIONS ALTERNATIVE BARS SHOULD BE WELDS SHALL DEVELOP THE FULL STRENGTH OF MEMBERS JOINED OTHERWISE SHOWN OR
SUSPENDED SLABS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20 mm DETAILED IN THE DRAWINGS. 10mm Ø 40 125 85 100
IN FLOOR SLABS, OPENINGS IN THE WALLS AND SLABS, INTERIOR PARTITIONS, LOCATION OF SPLICED. MIN. DISTANCE BET.
SLAB ON GRADE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 40 mm TWO ADJACENT BARS SPLICES 12mm Ø 50 165 115 115
DRAINS, ETC..
WALLS ABOVE GRADE - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25 mm SHALL BE 600mm.
5. IN CASE OF DISCREPANCIES AS TO THE LAYOUT, DIMENSIONS, AND ELEVATIONS BETWEEN BEAM STIRRUP AND COLUMN TIES - - - - - - - - - - - - - - - - - - 40 mm 16mm Ø 65 200 140 150

HALF OF "H"
THE STRUCTURAL PLANS, AND ARCHITECTURAL DRAWINGS, THE CONTRACTOR SHALL NOTIFY WHERE CONCRETE IS EXPOSED TO 20mm Ø 115 250 165 300
BOTH THE STRUCTURAL ENGINEER AND THE ARCHITECT.
6. ALL CONCRETE WORK SHALL BE DONE IN ACCORDANCE WITH THE ACI.318 BUILDING CODE
EARTH BUT POURED AGAINST FORMS - - - - - - - - - - - - - - - - 50 mm NOTES ON STRUCTURAL STEEL 25mm Ø 150 365 230 405
WHERE CONCRETE IS DEPOSITED TOP BARS @ SUPPORT (CONT.) 1. STRUCTURAL STEEL TO BE USED FOR FABRICATION AND ERECTION OF THIS STRUCTURE SHALL
REQUIREMENTS FOR THE REINFORCED CONCRETE AND ALL STRUCUTRAL STEEL WORK DIERECLTY AGAINST EARTH - - - - - - - - - - - - - - - - - - - - - - - - 75 mm
ACCORDING WITH AISC SPECIFICATION ( 9th EDITION) IN SO FAR AS THEY DO NOT CONFLICT REQ'D. BOTT. BARS @ SUPPORT COMPLY WITH ALL THE PERTINENT PROVISION OF AISC SPECIFICATION FOR THE DESIGN.
3. CONCRETE SHALL BE DEPOSITED IN ITS FINAL POSITION WITHOUT SEGREGATION. RE-HANDLING OR
WITH THE LOCAL BUILDING CODE REQUIREMENT. PLACING SHALL BE DONE PREFERABLY WITH BUGGIES, BUCKETS OR WHEELBARROWS, NO CHUTES FABRICATION AND ERECTION OF STRUCTURAL STEEL FOR BUILDING LATEST EDITION.
7. ACI REFERS TO AMERICAN CONCRETE INSTITUTE, AISC TO AMERICAN INSTITUTE OF STEEL WILL BE ALLOWED EXCEPT TO TRANSFER CONCRETE FROM HOPPERS TO BUGGIES, WHEELBARROWS 2. ALL STRUCTURAL STEEL SHAPES SHALL CONFORM TO ASTM A36 STRUCTURAL STEEL UNLESS
CONSTRUCTION AND ASTM TO AMERICAN SOCIETY FOR TESTING MATERIALS. OR BUCKETS IN WHICH CASE THEY SHALL NOT EXCEEED SIX (6) METERS IN AGGREGATE LENGTH. OTHERWISE INDICATED.
8. CONSTRUCTION NOTES AND TYPICAL DETAILS APPLY TO ALL DRAWINGS UNLESS OTHERWISE 4. NO DEPOSITING OF CONCRETE SHALL BE ALLOWED WITHOUT THE USE OF VIBRATORS UNLESS
SHOWN OR NOTED. MODIFY TYPICAL DETAILS AS DIRECTED TO MEET SPECIAL CONDITIONS. AUTHORIZED IN WRITING BY THE DEIGNERS AND ONLY FOR UNUSUAL CONDITIONS WHERE 3. ALL WELDED CONNECTIONS SHALL DEVELOP THE FULL STRENGTH OF THE MEMBERS CONNECTED.
9. SHOP DRAWINGS WITH ERECTION AND PLACING DIAGRAMS OF ALL STRUCTURAL STEELS, VIBRATORS ARE EXTREMELY DIFICULT TO ACCOMPLISH. 4. UNLESS OTHERWISE SPECIFIED ALL WELDING RODS SHALL CONFORM AWS E60 ELECTRODES.
MISCELLANEOUS IRON, PRE-CAST CONCRETE, ETC. SHALL BE SUBMITTED FOR ENGINEERS 5. ALL ANCHOR BOLTS, DOWELS, AND OTHER INSERTS, SHALL BE PROPERLY POSITIONED & SECURED IN 5. ALL BOLTS USED UNLESS OTHERWISE SPECIFIED SHALL BE ASTM A307 BOLTS.
APPROVAL BEFORE FABRICATION. BOTTOM BARS
PLACE PRIOR TO PLACING OF CONCRETE. AT MID SPAN
10. CONTRACTOR SHALL NOTE AND PROVIDE ALL MISCELLANEOUS CURBS, SILLS, STOOLS, 6. ALL CONCRETE SHALL BE KEPT MOIST FOR A MINIMUM OF SEVEN CONSECUTIVE DAYS IMMEDIATELY
EQUIPMENT'S AND MECHANICAL BASES THAT ARE REQUIRED BY THE ARCHITECTURAL, AFTER POURING BY THE USE OF WET BURLAP, FOG SPRAYING, CURING COMPOUNDS OR OTHER EXTRA TOP BARS
ELECTRICAL, AND MECHANICAL DRAWINGS. APPROVED METHODS. @ SUPPORT
11. ALL RESULTS OF MATERIAL TESTING FOR CONCRETE, REINFORCING BARS, & STRUCTURAL
STEEL MUST BE NOTED & APPROVED BY THE STRUCTURAL DESIGNER.
7. STRIPPING OF FORMS AND SHORES:
TYP. DETIAL OF COL. LAP SPLICE NOTES ON EMBEDDED PIPES
FOUNDATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24 HRS. A. ALL EMBEDDED PIPES FOR UTILTIES, ETC. THAT PASS THRU BEAMS SHALL NOT EXCEED 100mm
SUSPENDED SLAB EXCEPT WHEN & EXT. GIRDER TO COL CONNECT. DOOR
NOTES ON FOOTINGS ADDTIONAL LOADS ARE IMPOSED - - - - - - - - - - - - - - - - - - - 8 DAYS IN DIAMETER OR 31 BEAM DEPTH WHICHEVER IS LESS, UNLESS OTHERWISE APPROVED IN
WRITING BY THE STRUCTURAL ENGINEER.
OPENING
NOTE:
WALLS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21 DAYS
1. FOOTING ARE DESIGNED FOR AN ALLOWED SOIL BEARING PRESSURE OF 96 KPa ( 2 000psf ). BEAMS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14 DAYS B. PROVIDE THESE ADDTIONAL BARS FOR
NO PIPES SHALL BE ALLOWED TO PASS THRU BEAMS VERTICALLY. 38mm
CONTRACTOR SHALL REPORT TO THE ENGINEER, IN WRITING, THE ACTUAL SOIL CONDITIONS COLUMNS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21 DAYS ALL OPENINGS PLUS BARS ( NOT SHOWN) CLEAR
UNCOVERED AND CONFIRM ACTUAL BEARING OF SOIL BEFORE DEPOSITING CONCRETE. C. NO PIPES SHALL BE EMBEDED IN COLUMNS. WINDOW
8. THE CONTRACTOR SHALL SUBMIT THE SCHEDULE OF POURING AND THE LOCATION OF THE PARALLEL TO SIDE OF OPENING EQUAL
OPENING
TO THE NUMBER OF TERMINATED BARS
2. FOOTING SHALL REST AT LEAST 1500mm BELOW NATURAL GRADE LINE UNLESS OTHERWISE
INDICATED IN PLANS. NO FOOTING SHALL REST ON FILL.
CONSTRUCTION JOINTS TO THE STRUCTURAL ENGINEER AT LEAST (4) DAYS PRIOR TO THE POURING
FOR APPROVAL. NOTES ON BEAMS AND GIRDERS AT OPENING
3. MINIMUM CONCRETE PROTECTION FOR REINFORCEMENTS SHALL BE 75mm CLEAR FOR 9. THE CONTRACTOR SHALL FURNISH AND MAINTAIN ADEQUATE FORMS AND SHORINGS UNTIL
THE CONCRETE MEMBERS HAVE ATTAINED THEIR WORKING CONDITION AND STRENGTH. SEE ARCHITECTURAL & MECHANICAL
CONCRETE DEPOSITED THE GROUND AND 50mm FOR CONCRETE DEPOSITED AGAINST A 1. UNLESS, OTHERWISE NOTED IN PLANS, CAMBER ALL BEAMS AND GRDER AT LEAST 6mmØ PLANS FOR SLAB OPENING LOCATION.
FORMWORK. FOR EVERY 4.50M OF SPAN, EXCEPT CANTILEVERS FOR WHICH THE CAMBER SHALL BE AS
4. IN CASES WHERE THE SOIL CONDITION IS SUCH THAT THE MINIMUM ALLOWABLE SOIL PRESSURE NOTED IN PLANS OR AS ORDERED BY THE ENGINEER BUT IN NO CASE LESS THAN 20mm
OF 96 kPa ( 2 000psf ) CAN NOT BE ATTAINED AT PRACTICAL DEPTHS, THE USE OF MICROPILES, NOTES ON REINFORCEMENTS FOR EVERY 3.0M OF FREE SPAN
BORED PILES, OR DRIVEN PILES MAY BE ADOPTED IN LIEU OF STANDARD FOOTINGS. 2. TYPICAL BARS BENDING AND CUTTING DETAILS FOR BEAMS SHALL BE AS
1. UNLESS OTHERWISE NOTED IN PLANS, THE YIELD STRENGTH OF REINFORCING BARS SHALL BE: SHOWN IN FIG. B-1. TYP. EXTERIOR WINDOW & DOOR OPENING
NOTES ON CONCRETE SLABS A. FOOTINGS, FOOTING BEAMS AND GIRDERS - - - - - - - - - - fy = 276 MPa ( 40 000psi )
B. COLUMNS AND SHEAR WALLS - - - - - - - - - - - - - - - - - - - - fy = 276 MPa ( 40 000psi )
1. ALL SLAB REINFORCEMENTS SHALL BE 20mm CLEAR MINIMUM FROM BOTTOM AND FROM THE C. BEAMS AND GIRGER - - - - - - - - - - - - - - - - - - - - - - - - - - - fy = 276 MPa ( 40 000psi )
TOP OF SLAB. D. NON-LOAD BEARING WALL PARTITIONS, BEDDED SLABS, FLOOR & ROOF SLABS, PARAPETS,
CATCH BASIN, SIDE WALK. - - - - - - - - - - - - - - - - - - - - - - - - fy = 276 MPa ( 40 000psi )
2. UNLESS OTHERWISE SHOWN, REIFORCEMENT IN CONTINUOUS ELEVATED SLAB SHALL BE CUT AS
FOLLOWS: 2. ALL REINFORCED BARS SIZE 10mm OR LARGER SHALL BE DEFORMED IN ACCORDANCE WITH
TOP BAR ASTM A 706, BARS SMALLER THAN 10mm MAY BE PLAIN.
3. SPLICES SHALL BE SECURITY WIRED TOGETHER & SHALL LAP OR EXTEND IN ACCORDANCE W/
TABLE A & TABLE B ( TABLE OF LAP SPLICE & ANCHORAGE LENGTH ) UNLESS OTHERWISE SHOWN
ON DRAWINGS, SPLICES SHALL BE STAGGERED WHENEVER POSSIBLE.

BOTTOM BARS WEB BARS

BENT BAR 2-Ø12mm SIDE BARS
BOTTOM BAR
FIG. B-1 TOP BARS

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: S
DATE ISSUED
without his/ her permission. All drawings AS SHOWN ABOVE 4 4
CIVIL ENGINEER T.I.N. are to be returned when no longer in use. OWNER: DATE:
C.T.C.
 SERVICE
ENTRANCE
M GENERAL NOTES:

1 2 3 1.) ALL ELECTRICAL WORKS AND INSTALLATION SHALL COMPLY

2-8.O MM² THW STRANDED WIRE WITH THE APPLICABLE PROVISIONS OF THE LATEST EDITION OF
IN 2OMM 0 RSC PIPE THE PHILIPPINE ELECTRICAL CODE WITH THE RULES AND
REGULATIONS OF THE UTILITY COMPANY AND THE IMPLEMENTING
POLICIES OF THE LOCAL AUTHORITIES CONCERNED.

6O AT 2.) WORKMANSHIP SHALL BE OF THE HIGHEST STANDARDS AND

QUALITY. ALL MATERIALS TO BE USED FOR INSTALLATION SHALL
BE NEW AND/ OR APPROVED TYPE APPROPRIATE FOR THE
20AT 20AT PURPOSE OF APPLICATION.
L. OUTLET 1 2 C. OUTLET
3.) THERE SHOULD ONLY BE ONE SERVICE DROP TO THE
SPARE SPARE BUILDING ALL SERVICE ENTRANCE EQUIPMENT SUCH AS PANEL
BOARD CIRCUIT BREAKERS, ETC. SHALL BE PROPERLY
3 4 GROUNDED IN ACCORDANCE WITH THE REQUIREMENTS OF THE
CFL
PHILIPPINE ELECTRICAL CODE.
GROUND TERMINAL BLOCK
A 4.) ALL WIRING SHALL BE INSTALLED IN RIGID STEEL CONDUITS OR
3G FLEXIBLE CONDUIT PIPE RUN EMBEDDED IN SIDE THE CONCRETE
CFL AND HALLOW BLOCK STRUCTURES, SLAB, COLUMN WALLS,
3G
CFL CFL 2 RISER DIAGRAM PARTITIONS AND / OR CONCEALED BETWEEN DOUBLE WALL
E-1 SCALE 1: 70m WOODEN PARTITIONS, AND INSIDE THE CEILING SPACES WHERE
3G THE USE OF CONCEALED CONDUIT WIRING IN IMPRACTICABLE,
GROUND SURFACE METAL WIRING MAYBE USED.
CFL CFL
5.) WHEREVER REQUIRED AND NECESSARY, PULL BOXES OR
JUNCTION BOXED OF PROPER SIZES SHALL BE INSTALLED AT
B CONVENIENT AND INCONSPICUOUS LOCATIONS, ALTHOUGH SUCH
3G BOXES ARE NOT SHOWN ON PLANS NPR MENTIONED IN THE
CFL CFL
SPECIFICATIONS.

CFL 3G PB 6.) ALL WALL OUTLETS SHALL BE INSTALLED AL THE FOLLOWING

2
HEIGHTS ABOVE THE FINISHED FLOOR LINE. UNLESS OTHERWISE
PB

3G NOTED:
C
A. WALL SWITCHES 127Omm ABOVE FLOOR LINE
PB B. DUPLEX CON, OUTLETS 3OOmm ABOVE FLOOR LINE
CFL 1
C. PANEL BOARD 127Omm ABOVE FLOOR LINE
D D. KILOWATT HOUR METER 185Omm ABOVE FLOOR
LINE

7.) ALL ELECTRICAL WORKS AND INSTALLATIONS SHALL BE DONE

UNDER THE DIRECT AND IMMEDIATE SUPERVISION OF A DULLY
LICENSED ELECTRICAL ENGINEER OR A REGISTERED
ELECTRICIAN.

1 LIGHTING AND POWER LAYOUT PLAN 8.) NO REVISION IN THE DESIGN SHALL BE DONE WITHOUT THE
E-1 SCALE 1: 100m PRIOR KNOWLEDGE AND APPROVAL OF THE DESIGNER AND
THE OWNER A NY SUCH REVISION DONE WITHOUT APPROVAL
SHALL CAUSE RESPONSIBILITY OF THE CEASE AS A WHOLE

SCHEDULE OF LOADS AND COMPUTATION : PB- 1

CKT. TOTAL VOLTAGE CB

LEGEND
LOAD DESCRIPTION SIZE WIRE CONDUIT SIZE
NO. WATTAGE RATING RATING CONNECTED LOAD (VA) = 316O
PENLIGHT OUTLET KILOWATT HOUR METER
2-3.5mm² THHN STRANDED WIRE M
1 1oX1OO LIGHT OUTLET 1ooo 230 2O A IT = 316O VA + 25% (17A) USE : 4O AT / 1OO AF, 2P, 24O V
1-3.5mm² TW(G) STRANDED WIRE IN 2OMM PVC 23O FLUORESCENT OUTLET CONVENIENCE OUTLET
216O 230 2O A 2-3.5mm² THHN STRANDED WIRE IT = 13.73 + 4.25 1FEEDER = 2O.667 X 1.25
2 6X36O CON. OUTLET
1-3.5mm² TW(G) STRANDED WIRE IN 2OMM PVC CIRCUIT HOMER ACLU OUTLET
= 25.833 ACLU
= 17.98
3 SPARE USE : 2-8.O MM² THW STRANDED WIRE
CIRCUIT LINE S SINGLE GANG SWITCH
IDF @ 1OO% DF =17.98 A IN 2OMM 0 RSC PIPE
4 SPARE S2 DOUBLE GANG SWITCH
ICB = 17.98 X 1.15 SWITCH LINE

316O 4OAT, 1OOAF, 2P, 24OV = 2O.667 PANEL BOARD S3 TRIPLE GANG SWITCH

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREY

SHEET CONTENTS REVISIONS CAD BY: SHEET NO.
DATE REMARKS
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING
PLACE ISSUED ENGINEER as such must not be
reproduced or copied in part or in whole
LOCATION: CHECK BY: E
DATE ISSUED
without his/ her permission. All drawings 1
ELECTRICAL ENGINEER / MASTER ELECTRICIAN
T.I.N. are to be returned when no longer in use. OWNER: AS SHOWN DATE:
C.T.C.
 VS
TR

1 2 3

TOSEW
EX ER
IST LIN
2.50
IN E
SEWER LINE G
TO EXISTING

0.12
SV
O
C. CO
VS
SV TR
MANHOLE

1.50
INLET

FD
F W FD
C.O

FD C
E
R PIP F CO OUTLET
C.
C.O F PP F LAV O F C.
VSTR "Ø O
1/2

0.12
A F GV
F
SINK
C.O WM
CV PLAN
FR
.W
AT
ER
SU
PP
LY 2.50
FD
1 ISOMETRIC LAYOUT MANHOLE MANHOLE

F WC F
LAV P-2 SCALE DNTS
F
B OUTLET
AIR SPACE AIR SPACE
ADJUSTABLE
STRAINER
1/2" Ø PPR PIPE

CAST IRON
BODY DRAIN

1.50
REINFORCED
CONCRETE
SLAB
BIDET

C FLEXIBLE HOSE
FLEXIBLE HOSE
DIGESTIVE CHAMBER LEACHING CHAMBER

WATER CLOSET
SLUDGE PIT 1% SLOPE
SLUDGE PIT 1% SLOPE

D GV EARTH FILL
GRAVEL BASE GRAVEL BASE
ANGLE VALVE

WM
SECTION
CV
P-TRAP 4 SEPTIC VAULT DETAIL
P-1 SCALE 1:40
FR. WATER SUPPLY
WATER CLOSET DETAIL FLOOR DRAIN DETAIL

1 PLUMBING LAYOUT
P-1 SCALE 1: 100m BRASS PLUG
COUNTER SUNK HEAD

FLOOR TILES
REINFORCED CL 4LBS LEAD VENT
CONCRETE
SLAB FLOOR FIN. FLOOR TILES FLASHING CAP

FLOOR ELASTOMERIC
NOTES AND SPECIFICATION LEGEND ROOFING
MEMBRANE

BASE FELT
CB CATCH BASIN CO CLEAN OUT

VARIES
ALL PLUMBING WORKS AND INSTALLATIONS SHALL BE DTWO IN ACCORDANCE WITH THE LATEST EDITION OF R.C. SLAB

VARIES
ELASTOMERIC
NATIONAL PLUMBING CODE OF THE PHILIPPINES RULES AND REGULATIONS AND ALL GOVERNMENT AGENCIES SV SEPTIC VAULT FLASHING
KS KITCHEN SINK PLUG
HAVING JURISDICTION OVER THIS PROJECT. VENT THRU ROOF
VTR
GRAVEL
ALL SOIL PIPES AND FITTINGS SHALL BE PVC SCHEDULE 40 AND OF APPROVED TYPE PVC SOLVENT
LAV LAVATORY F FAUCET BED

CEMENT SHALL BE APPROVED AS SEALANT FOR ALL JOINT.

FD FLOOR DRAIN SD SHO. DRAIN 1/8 (45°) BEND
ALL VENTS SHALL BE 50MM o PVC SCHEDULE 40 AND SHALL EXCEED @ LEAST 300MM ABOVE THE ROOF.
HB HOSE BEB WATER LINE
ALL WATER LINES SHALL BE GALVANIZED IRON (G.I.) SCHEDULE 40 20MM o FOR MAIN OR ENTRANCE PIPES
CV CHECK VALVE
12MM o FOR BRANCH PIPES 10MM o FOR FITTING. SANITARY LINE
GV GATE VALVE 1/8 (45°) BEND VENT THRU ROOF DETAIL
1/8 (45°) BEND
ALL PLUMBING WORKS AND INSTALLATIONS SHALL BE DTWO OR LAID UNDER CLOSED AND DIRECT
SUPERVISION OF MASTER PLUMBER. WM WATER METER DRAINAGE LINE

CLEAN-OUT DETAILS

PRC REG. NO. PROJECT TITLE: PROPOSED ONE (1) STOREYSHEET CONTENTS REVISIONS CAD BY: SHEET NO.
PTR NO. This drawing as an instrument of service
is a property of REGISTERED CIVIL
RESIDENTIAL BUILDING DATE REMARKS

PLACE ISSUED ENGINEER as such must not be

reproduced or copied in part or in whole
LOCATION: CHECK BY: P
DATE ISSUED
without his/ her permission. All drawings 1 1
T.I.N. are to be returned when no longer in use. OWNER: AS SHOWN DATE:
MASTER PLUMBER
C.T.C.