User Manual D4085 Issue: 08/05

DISPLAY/KEYBOARD ASSEMBLIES
for
RTU 3310, DPC 3330 & DPC 3335

F1 F2 F3 F4 INIT

7 8 9
Local
ALM ALM
4 5 6 I/E ACK for
TOTA L . F L OW . R A T E
1
A/M
OPER DPC 3330
2 3 I/E
1 24 8 . 9 7 6 MC F H ON
? 1 2 3C E ME A E H I ! 0
NEX T B A CK MU L T EX I T DEL ENT
OFF

4 X 20 Display 4 X 20 Display
Remote Only Membrane Keyboard 5 X 5 Membrane Keyboard

R E Y NOL D S GA S S Y S T EM
R E Y NOL D S GA S S Y S T EM
L OC K P O R T S T A T I ON L OC K P O R T S T A T I ON
8 RUN S 8 RUN S
S I GN ON S CROL L S I GN ON S CROL L

F1 F2 F3 F4

F1 F2 F3 F4 INIT
7 8 9 INIT
7 8 9

4 5 6 ALM ALM ALM ALM

I/E ACK 4 5 6 I/E ACK

1 OPER
1 2 3 A/M I/E
2 OPER ON
3 A/M
I/E
ON
0
DEL ENT
OFF
0
-
OFF
DEL ENTER

Bristol Babcock
Bristol Babcock BRISTOL
BABCOCK

Remote for DPC 3330 & DPC 3335 Remote for DPC 3330 & DPC 3335

Bristol Babcock
 NOTICE
Copyright Notice

The information in this document is subject to change without notice. Every effort has been
made to supply complete and accurate information. However, Bristol Babcock assumes no
responsibility for any errors that may appear in this document.

Request for Additional Instructions

Additional copies of instruction manuals may be ordered from the address below per
attention of the Sales Order Processing Department. List the instruction book numbers or
give complete model number, serial or software version number. Furnish a return address
that includes the name of the person who will receive the material. Billing for extra copies
will be according to current pricing schedules.

ACCOL® is a registered trademark of Bristol Babcock. Other trademarks or copyrighted

products mentioned in this document are for information only, and belong to their
respective companies, or trademark holders.

Copyright© 2005 Bristol Babcock, 1100 Buckingham St., Watertown, CT 06795. No part of
this manual may be reproduced in any form without the express written permission of
Bristol Babcock.
 IMPORTANT! READ INSTRUCTIONS BEFORE STARTING!

Be sure that these instructions are carefully read and understood before any
operation is attempted. Improper use of this device in some applications may result
in damage or injury. The user is urged to keep this book filed in a convenient
location for future reference.

These instructions may not cover all details or variations in equipment or cover
every possible situation to be met in connection with installation, operation or
maintenance. Should problems arise that are not covered sufficiently in the text, the
purchaser is advised to contact Bristol Babcock for further information.

EQUIPMENT APPLICATION WARNING

The customer should note that a failure of this instrument or system, for
whatever reason, may leave an operating process without protection. Depending
upon the application, this could result in possible damage to property or injury to
persons. It is suggested that the purchaser review the need for additional backup
equipment or provide alternate means of protection such as alarm devices, output
limiting, fail-safe valves, relief valves, emergency shutoffs, emergency switches, etc.
If additional information is required, the purchaser is advised to contact Bristol
Babcock.

RETURNED EQUIPMENT WARNING

When returning any equipment to Bristol Babcock for repairs or evaluation,

please note the following: The party sending such materials is responsible to ensure
that the materials returned to Bristol Babcock are clean to safe levels, as such levels
are defined and/or determined by applicable federal, state and/or local law
regulations or codes. Such party agrees to indemnify Bristol Babcock and save
Bristol Babcock harmless from any liability or damage which Bristol Babcock may
incur or suffer due to such party's failure to so act.

ELECTRICAL GROUNDING

Metal enclosures and exposed metal parts of electrical instruments must be

grounded in accordance with OSHA rules and regulations pertaining to "Design
Safety Standards for Electrical Systems," 29 CFR, Part 1910, Subpart S, dated: April
16, 1981 (OSHA rulings are in agreement with the National Electrical Code).

The grounding requirement is also applicable to mechanical or pneumatic

instruments that include electrically-operated devices such as lights, switches, relays,
alarms, or chart drives.

Bristol Babcock 1100 Buckingham Street, Watertown, CT 06795

Telephone (860) 945-2200
 WARRANTY

A. Bristol warrants that goods described herein and manufactured by Bristol are free
from defects in material and workmanship for one year from the date of shipment
unless otherwise agreed to by Bristol in writing.

B. Bristol warrants that goods repaired by it pursuant to the warranty are free from
defects in material and workmanship for a period to the end of the original warranty
or ninety (90) days from the date of delivery of repaired goods, whichever is longer.

C. Warranties on goods sold by, but not manufactured by Bristol are expressly limited
to the terms of the warranties given by the manufacturer of such goods.

D. All warranties are terminated in the event that the goods or systems or any part
thereof are (i) misused, abused or otherwise damaged, (ii) repaired, altered or
modified without Bristol's consent, (iii) not installed, maintained and operated in
strict compliance with instructions furnished by Bristol, or (iv) worn, injured or
damaged from abnormal or abusive use in service time.

E. THESE WARRANTIES ARE EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES EXPRESS OR IMPLIED (INCLUDING WITHOUT LIMITATION
WARRANTIES AS TO MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE), AND NO WARRANTIES, EXPRESS OR IMPLIED, NOR ANY
REPRESENTATIONS, PROMISES, OR STATEMENTS HAVE BEEN MADE BY
BRISTOL UNLESS ENDORSED HEREIN IN WRITING. FURTHER, THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE
FACE HEREOF.

F. No agent of Bristol is authorized to assume any liability for it or to make any written
or oral warranties beyond those set forth herein.

REMEDIES

A. Buyer's sole remedy for breach of any warranty is limited exclusively to repair or
replacement without cost to Buyer of any goods or parts found by Seller to be
defective if Buyer notifies Bristol in writing of the alleged defect within ten (10) days
of discovery of the alleged defect and within the warranty period stated above, and if
the Buyer returns such goods to Bristol's Watertown office, unless Bristol's Water-
town office designates a different location, transportation prepaid, within thirty (30)
days of the sending of such notification and which upon examination by Bristol
proves to be defective in material and workmanship. Bristol is not responsible for
any costs of removal, dismantling or reinstallation of allegedly defective or defective
goods. If a Buyer does not wish to ship the product back to Bristol, the Buyer can
arrange to have a Bristol service person come to the site. The Service person's
transportation time and expenses will be for the account of the Buyer. However,
labor for warranty work during normal working hours is not chargeable.

B. Under no circumstances will Bristol be liable for incidental or consequential damages

resulting from breach of any agreement relating to items included in this quotation
from use of the information herein or from the purchase or use by Buyer, its
employees or other parties of goods sold under said agreement.
 Bristol Babcock
Training
GET THE MOST FROM YOUR BRISTOL
BABCOCK INSTRUMENT OR SYSTEM

• Avoid Delays and problems in getting your system on-line

• Minimize installation, start-up and maintenance costs.

• Make the most effective use of our hardware and software.

• Know your system.

As you know, a well-trained staff is essential to your operation. Bristol Babcock offers a full
schedule of classes conducted by full-time, professional instructors. Classes are offered
throughout the year at three locations: Houston, Orlando and our Watertown, CT
headquarters. By participating in our training, your personnel can learn how to install,
calibrate, configure, program and maintain any and all Bristol Babcock products and
realize the full potential of your system.

For information or to enroll in any class, contact our training department in Watertown at
(860) 945-2343. For Houston classes, you can also contact our Houston office, at (713) 685-
6200.
BLANK PAGE
A Few Words About Bristol Babcock

For over 100 years, Bristol7 has been providing innovative solutions for the measurement
and control industry. Our product lines range from simple analog chart recorders, to
sophisticated digital remote process controllers and flow computers, all the way to turnkey
SCADA systems. Over the years, we have become a leading supplier to the electronic gas
measurement, water purification, and wastewater treatment industries.

On off-shore oil platforms, on natural gas pipelines, and maybe even at your local water
company, there are Bristol Babcock instruments, controllers, and systems running year-in
and year-out to provide accurate and timely data to our customers.

Getting Additional Information

In addition to the information contained in this manual, you may receive additional assis-
tance in using this product from the following sources:

Help Files / Release Notes

Many Bristol Babcock software products incorporate help screens. In addition, the software
typically includes a ‘read me’ release notes file detailing new features in the product, as
well as other information which was available too late for inclusion in the manual.

Contacting Bristol Babcock Directly

Bristol Babcock's world headquarters are located at 1100 Buckingham Street, Watertown,
Connecticut 06795, U.S.A.

Our main phone numbers are:

(860) 945-2200
(860) 945-2213 (FAX)

Regular office hours are Monday through Friday, 8:00AM to 4:30PM Eastern Time,
excluding holidays and scheduled factory shutdowns. During other hours, callers may leave
messages using Bristol's voice mail system.

Telephone Support - Technical Questions

During regular business hours, Bristol Babcock's Application Support Group can provide
telephone support for your technical questions.

For technical questions about TeleFlow products call (860) 945-8604.

For technical questions about ControlWave call (860) 945-2394 or (860) 945-2286.

For technical questions regarding Bristol’s OpenEnterprise product, call (860) 945-3865
or e-mail: [email protected]
For technical questions regarding ACCOL products, OpenBSI Utilities, UOI and all other
software except for ControlWave and OpenEnterprise products, call (860) 945-2286.

For technical questions about Network 3000 hardware, call (860) 945-2502.

You can e-mail the Application Support Group at: [email protected]

The Application Support Group maintains an area on our web site for software updates and
technical information. Go to: www.bristolbabcock.com/services/techsupport/

For assistance in interfacing Bristol Babcock hardware to radios, contact Bristol Babcock’s
Communication Technology Group in Orlando, FL at (407) 629-9463 or (407) 629-
9464.

You can e-mail the Communication Technology Group at:

[email protected]

Telephone Support - Non-Technical Questions, Product Orders, etc.

Questions of a non-technical nature (product orders, literature requests, price and delivery
information, etc.) should be directed to the nearest sales office (listed on the rear cover of
this manual) or to your Bristol-authorized sales representative.

Please call the main Bristol Babcock number (860-945-2200) if you are unsure which office
covers your particular area.

Visit our Site on the World Wide Web

For general information about Bristol Babcock and its products, please visit our site on the
World Wide Web at: www.bristolbabcock.com

Training Courses

Bristol Babcock’s Training Department offers a wide variety of courses in Bristol hardware
and software at our Watertown, Connecticut headquarters, and at selected Bristol regional
offices, throughout the year. Contact our Training Department at (860) 945-2343 for course
information, enrollment, pricing, and scheduling.
 D4085
DISPLAY/KEYBOARD ASSEMBLIES
for
RTU 3310, DPC 3330 & DPC 3335

TABLE OF CONTENTS
SECTION TITLE PAGE #

SECTION 1 OVERVIEW ....................................................................................................................... 1

SECTION 2 PREPARING THE ACCOL LOAD ................................................................................... 4
Step 1: Creating the Identifier Display ............................................................................ 4
Step 2: Defining a Scroll List ............................................................................................ 5
Step 3: Assigning Passwords............................................................................................. 6
Step 4: Assigning Monitoring Signals .............................................................................. 7
Step 5: Defining the List Menu......................................................................................... 8
SECTION 3 USING THE KEYBOARD ................................................................................................ 9
SCROLLING .................................................................................................................... 10
SIGNING-ON................................................................................................................... 10
USING THE CLOCK FUNCTIONS............................................................................... 11
Changing the Time ...................................................................................................... 12
Changing the Date....................................................................................................... 12
CHOOSING A SIGNAL LIST FROM THE LIST MENU ............................................. 12
MOVING THROUGH A SIGNAL LIST ......................................................................... 13
CHANGING SIGNAL PARAMETERS .......................................................................... 14
SIGNING-OFF................................................................................................................. 17
INTERPRETING ERROR MESSAGES ......................................................................... 17

APPENDICES

CW_10 4 X 20 Display-Keyboard Assembly.............................................. Appendix DKA

CW_30 4 X 20 Display-Keyboard Assembly.............................................. Appendix DKB

D4085 Contents / 0-1

BLANK PAGE
SECTION 1 - OVERVIEW
Bristol Babcock Display/Keyboard assemblies provide a built-in, local, user interface for the
DPC 3330 or RTU 3310 or a choice of two unique remote Display/Keyboard assemblies for
the DPC 3330 or DPC 3335. These assemblies allow an operator or engineer to view and
modify ACCOL signal values and associated status bit information. ACCOL signals include
inputs, process variables, calculated variables, constants, setpoints, tuning parameters and
outputs used in a measurement or control application. Status bits include alarm state,
alarm acknowledge, control, manual, and questionable data (see note 1).

Note 1: Questionable Data Status requires firmware level AL.00, RMS02, or later.

Setting up the Display/Keyboard is a simple matter of creating a Keyboard Module in the

ACCOL load. Use the terminals on the Keyboard Module to specify passwords and signal
lists.

The ‘local’ Display/Keyboard is comprised of a four line by twenty character liquid crystal
display, with adjustable viewing angle, and a five-by-five membrane key matrix. Each key
has a microswitch for positive tactile feedback. This means that as you firmly depress the
keys, you will feel it click as it engages. The ‘local’ Display/Keyboard is located in the front
panel of the DPC 3330 or RTU 3310 and can be installed at the factory or added later. A
choice of two ‘remote’ Display/Keyboard assemblies are available for use in conjunction with
the DPC 3330 or DPC 3335. These units are designed to be mounted "remotely." The LCD
Display assembly is identical to the one used in the ‘local’ assembly, while the keyboard
section may be either the same five-by-five membrane key matrix used in the ‘local’
Display/Keyboard assembly (see Figures 1, 2, 3 & 22) or the remote only membrane key
matrix shown in Figures 4 & 23.

If you're setting up the keypad, follow the configuration instructions in Section 2.

Figure 1 - Local Display/Keyboard Assembly - DPC 3330

D4085 3310/30/35 Display/Keyboard / 1

If your keyboard has already been set up, Section 3 will tell you how to use the keyboard
and interpret the display.

Figure 2 - Local Display/Keyboard Assembly - RTU 3310

2 / 3310/30/35 Display/Keyboard D4085

 Figure 3 - Remote Unit of Extended 4 X 20 Display/5 X 5 Membrane Key Matrix
Keyboard System - DPC 3330 & DPC 3335)

Figure 4 - Remote 4 X 20 Display/Remote Only Membrane Key Matrix

Keyboard Assembly - DPC 3330/DPC 3335

D4085 3310/30/35 Display/Keyboard / 3

SECTION 2 - PREPARING THE ACCOL LOAD
In order for the keyboard and display to operate, the ACCOL load must include a properly
configured Keyboard Module. Use the ACCOL Interactive Compiler (AIC) or ACCOL Batch
Compiler (ABC) to create this module in Task 0 and assign the terminals according to the
five steps below.

Figure 5 - Keyboard Module Symbol

Step 1: Creating the Identifier Display

The Identifier Display is the first display to appear when the ACCOL load begins to
execute. This display will look similar to Figure 6C. Each of the first three lines of the
display contains the text value of a string signal. These string signals are named on the
SELECT terminals of the Keyboard Module (See Figure 5). Since this is the first display
that the user will see, you may want the display to contain general information such as the
node name of the controller or the process that the controller is monitoring.

The bottom line on the display is called the legend line. It shows which function keys are
currently active and their purpose. Function keys are those keys on the Keypad that are
marked ([F1] through [F4]). Function key assignments are preconfigured and cannot be
changed. Using function keys is described in Section 3, Using the Keyboard.

The legend line in Figure 6C shows that the user has two choices: to sign-on (using [F1]) or
scroll (using [F3]).

4 / 3310/30/35 Display/Keyboard D4085

 Figure 6 - Creating the Identifier Message

Step 2: Defining a Scroll List (see Figure 7)

Once the Keyboard Module has been configured and the Keyboard is operating properly,
you can automatically scroll through a list of signals. Scrolling can be done without
entering a password (discussed in the next step.) The signals in the list are displayed one at
a time and in the same order in which they were entered in the signal list. This list might
contain summary information about the process the RTU/DPC 33XX is controlling.

D4085 3310/30/35 Display/Keyboard / 5

 Figure 7 - Defining a Scroll List Diagram

(Later, we'll discuss other signal lists that can be accessed with the keypad. To distinguish
this list from others, let's call this signal list the Scroll List.)

On the LIST terminal, enter the number of a signal list to be scrolled. (You may also enter a
signal name whose value equals the number of the signal list.) This signal list becomes the
Scroll List. The Scroll List can contain different types of signals (that is, logical, analog and
string). You can create a specific scroll signal list or use any list in the ACCOL load.

Each signal in the Scroll List will be displayed for the number of seconds defined at the
TIME terminal. If you don't specify a time on this terminal, the hold time will be two
seconds. If you signed-on and then started scrolling you will be signed-off in 20 minutes if
no keys are pressed. If this is unacceptable, sign-off (INIT key) before starting scrolling.

Step 3: Assigning Passwords (see Figure 8)

Once the Display/Keyboard is operating, a password will be needed to go beyond the initial
displays. These passwords are defined on the PASSWORD_RD and PASSWORD_WT
terminals.

Someone using the password named on the PASSWORD_RD terminal will only be allowed
to read signal information. When the password named on the PASSWORD_WT terminal is
used, that person can also change signal values and other parameters.

These terminals can accept a value or signal name.

Passwords can be any combination of numbers up to 6 digits in length, from 000001 to

999999. If none are specified on the Keyboard Module, the default values are 333333 for
read only access and 666666 for read/write access.

6 / 3310/30/35 Display/Keyboard D4085

 Figure 8 - Assigning Passwords Diagram

Step 4: Assigning Monitoring Signals (see Figure 9)

Enter signal names on the STATE, FAIL_STATE, and STATUS terminals.

Figure 9 - Assigning Monitoring Signals Diagram

Enter a logical alarm signal name on the STATE terminal. This signal will turn ON when a
valid password has been entered. It will be set OFF when the user has signed off. In each
case, an alarm will be reported to notify the network of this activity.

D4085 3310/30/35 Display/Keyboard / 7

Enter a logical alarm signal name on the FAIL_STATE terminal. The module will turn the
signal ON after three invalid passwords have been entered. It will be turned off when the
user signs off. In each case an alarm will be reported.

Enter an analog signal name on the STATUS terminal. When the load is executing, the
value of this signal, when read by the PEI, will indicate the present module state. The
signal will assume one of the following codes:

STATUS code: Meaning

1.0 no keypad hardware detected

2.0 waiting for a key press
3.0 waiting for key press or timeout
4.0 writing to display
5.0 writing to display
6.0 clearing LCD display

Step 5: Defining the List Menu (see Figure 10)

The INPUT terminals are used to define the menu and signal lists to be accessed from the
List Menu. Once the Keyboard is operating, a user who has signed on with a password can
scroll through the names of signal lists and choose a list to read or change.

Figure 10 - Defining the List Menu Diagram

Up to 255 INPUT terminals are available. Each terminal can contain a signal list number
or signal name. These terminals should be used consecutively, that is, unwired INPUT
terminals should only appear after the last used INPUT terminal and will generate an
'unwired input' message on the display. Unwired terminals between wired terminals will
use memory space. Unwired terminals after the last used terminal do not use memory.

If the terminal is assigned a number, this number will be presented on the List Menu.
When the terminal is assigned a signal name, both the signal name and its value are shown
on the List Menu.

This concludes this section on configuring the Keyboard Module. If you have properly con-
figured the Keyboard Module, you will see the Identifier Display when the ACCOL load
begins to execute.

8 / 3310/30/35 Display/Keyboard D4085

The next section describes how to use the keyboard to access signal information.

SECTION 3 - USING THE KEYBOARD

The Identifier Display is the starting point from which you can go to other displays. It
shows an identification message and the words SIGN-ON and SCROLL at the bottom of the
screen (see Note 2). The identification message may contain the name of the controller, the
plant equipment it is monitoring, or the signals you can expect to see when you use this
display.

Note 2 : If your display shows something else, press the [F4] key until you see the words
SIGN-ON and SCROLL on the bottom line.

If your screen is blank, turn the brightness screw clockwise. This screw is located to
the left of the keyboard. If no letters appear, the controller has not been programmed
properly to operate the keypad.

The words SIGN-ON and SCROLL at the bottom of the screen are on the legend line. It
tells you which function keys (that is, key [F1] through [F4]) are active and their purpose at
that time.

Figure 11 - The Identifier Display

Up to four legends can appear on the legend line. The legend on the far left corresponds to
the function of the [F1] key. The assignment for the [F4] key is on the far right. Keys [F2]
and [F3] are described to the left and right of center. When no legend appears, that function
key is not active at that time. For example, in Figure 11 only [F1] and [F3] are active.

Figure 12 - Identifier Display Legends and Corresponding Keyboard Alignment

for 5 X 5 Membrane Key Matrix Keyboard System

D4085 3310/30/35 Display/Keyboard / 9

From the Identifier Display, you have two choices. Pressing [F1] will allow you to sign-on if
you have a password. By pressing [F3] you can activate automatic scrolling through a list of
signals.

SCROLLING

To begin automatic scrolling, press [F3] from the Identifier Display (Figure 7). Signal in-
formation will appear on the screen and remain there for 2 to 10 seconds. The signal name
appears on the first line. Signal value and units appear on the second line and status
appears on the third line. An example is shown in Figure 13.

Figure 13 - Scrolling

When all signals in the list have been displayed, they will be shown again in the same
order.

Press HOLD ([F1]) to halt scrolling and freeze the display. Press GO ([F2]) to resume
scrolling.

Press EXIT ([F4]) to return to the Identifier Display (Figure 11).

SIGNING-ON

To access the List Menu, you must first sign-on with a proper password. From the
Identifier Display (Figure 11), press [F1]. The screen will look like Figure 14A or 14B.

If the display looks like Figure 14B:

Someone else has already signed on. Go to the paragraph below that starts "Once the
correct password has been entered...".

If the display looks like Figure 14A:

Enter a password using the 0 to 9 keys. For security, asterisks will appear as you enter
the digits. If you make a mistake, press [F1] and try again. Press [ENT] to enter your
password into the system.

If your password is not recognized, the asterisks will be erased after you press [ENT].
Check your password and try again. After three unsuccessful attempts to sign-on, an
alarm message is generated within the controller and reported to the external network.

10 / 3310/30/35 Display/Keyboard D4085

Once the correct password has been entered, the display will look like Figure 14B.

Figure 14 - Signing On

When the second line shows READ/WRITE, you can read and write signal parameters.
When it shows READ ONLY you cannot change signal parameters. You are only permitted
to read signal information. If your display shows READ ONLY and you want to change
signal values, sign-off (press the [INIT] key), press [F1] from the Identifier Display, and
enter the password for READ/WRITE access.

Once you have successfully signed on, the legend line will show that you have three options.
You can view and change the time and date of the local clock, access more signal lists, or
return to the Identifier Display. Let's start by setting the local clock.

USING THE CLOCK FUNCTIONS

From the Sign-On Display (Figure 14B), press [F1]. The screen will show the present date
and time and will look like Figure 15. Follow the instructions below to change the time or
date. When you're finished, press [F4] to exit.

Figure 15 - Clock Display

Today's date is shown in the first line in the format month/day/year.

The current time is shown in the format hours:minutes:seconds.

D4085 3310/30/35 Display/Keyboard / 11

Changing the Time

From the display shown in Figure 15, press [F1]. Colons (:) will appear on the third line.
Enter the new time there and press [ENT]. Valid times range from 00:00:00 to 23:59:59.
Invalid entries will be ignored. The display will be updated to show the new time.

Figure 16 - Time Set Display

If you make a mistake while entering the new time, press [CLR] and start again or use
[DEL] to backspace and delete one character at a time.

Press [F2] to return to the clock display (Figure 15.

Changing the Date

From the clock display (Figure 15, press [F2]. Slash marks (/) will appear on the third line.
Enter the new date there and press [ENT].

Figure 17 - Date Set Display

If you make a mistake while entering the new date, press [CLR] and start again or use
[DEL] to back space and delete one character at a time.

Press [F4] to return to the Sign-On Display (Figure 10B).

CHOOSING A SIGNAL LIST FROM THE LIST MENU

The List Menu is another area where signal information can be seen. As explained earlier
in this section, your first opportunity to read signal information is by choosing the SCROLL
function from the Initial Display. Signal name, value and units text are presented from the
Scroll List. This function is available to all users even without signing-on.

12 / 3310/30/35 Display/Keyboard D4085

The List Menu will show other groups of signals which you can choose to read. This in-
formation will be more detailed than the Scroll List.

To get to the List Menu, choose MENU (press [F2]) from the Sign-On Display (Figure 14B).

The first signal list number in the menu will appear on the first line. If a signal name was
used to name the list in the ACCOL load, the signal name appears on the second line;
other-wise, the display indicates NO NAME.

Figure 18 - Using the List Menu Display

Press NEXT and BACK to see the other signal lists that are available in the List Menu. The
List Menu can contain up to 255 signal list numbers.

To advance or backup in large increments, enter a one to three digit number on line 3 and
press NEXT or BACK. For example, if the fifth signal is being displayed and you enter the
number 22 and press NEXT, the twenty-seventh signal will appear.

Wraparound will occur for increments exceeding the list length. For example, suppose the
second signal in a 10-signal list is displayed. If the number 11 is entered and NEXT is
pressed, the third signal in the list will be displayed.

To move directly to a list, enter the list number, then press pick.

MOVING THROUGH A SIGNAL LIST

After READ or CONF has been pressed, the display will show the first signal in the list. An
example is shown in Figure 19. Each time NEXT is pressed the display will show the next
signal in the list. BACK will show the previous signal.

To move in large increments, enter a one to three digit skip count and press NEXT. The dis-
play will skip over that number of signals. The maximum skip count is 255; larger values
default to 255.

D4085 3310/30/35 Display/Keyboard / 13

Automatic wraparound occurs in either direction. When you reach the end of the list, [F1]
will display the first signal again. At the top of the list, [F2] will display the last signal. You
can skip through long lists by entering a one to three digit number and pressing NEXT or
BACK. For example, to move 50 signals down the list, press 5, then 0, then [F1].

CHANGING SIGNAL PARAMETERS

From Figure 18, you can change signal parameters by pressing CONF [F2]. Then follow the
directions summarized below (see Note 3).

Note 3: If your display does not contain the legend CONF in the legend line, your password
will only allow you to read signals. If you want to change signal values at this time,
you must first sign-off and then sign-on using the correct password. See your
Systems Engineer for the correct password.

Before making any changes, first check the signal inhibit status field (See Figure 19). When
the display shows ME (manual enable) you can change signal parameters. When it shows
MI (manual inhibit), you cannot alter the parameters of this signal. If the field indicates
MI, press the OPER IE key to change it to ME.

To change an analog value:

Press CLR to clear the third line. Use the number keys 0 through 9 to enter the new
value. The minus sign and period are also permitted. Press [ENT].

If you make a mistake, press CLR and enter the number again or use the [DEL] key to
erase a character.

Another way to enter new values is by using the arrow up and arrow down keys (located
below the [F4] and [INIT] keys). These keys will raise and lower the value by 1% of the
displayed amount.

To change the status of a logical signal:

Press CLR, then use either the down and up arrow keys or the [0/OFF] and [1/ON] keys
to change the state of a logical signal. If the [0/OFF] and [1/ON] keys are used, you must
also press [ENT].

14 / 3310/30/35 Display/Keyboard D4085

 Figure 19 - Interpreting Signal Information

Notes for Figure 19

1. Signal Name - base name, extension, and attribute

2. Value - analog value, string value, or logical value. Values which cannot fit in this field will be
shown as asterisks.

Analog values are displayed in floating point format, for example, 0.0125, 99.627, and 1287.66.
When the value cannot be shown in floating point format, scientific format is used
(1.287668E+10 or 1.25E-02 for example).

3. Questionable Data Status - for analog signals, column 1 will be clear if the status is valid. It will
display a question mark if the status is questionable (requires Firmware Level AL.00 or
RMS02 or later).

4. Skip - how far to move in the list when NEXT or BACK is pressed (Default = 1, Max = 255).

5. Signal Inhibit Status

CE (Control Enable) means this signal can be updated by the ACCOL program.

CI (Control Inhibit) means the signal cannot be updated by the ACCOL program.

ME (Manual Enable) means the signal can be changed manually.

MI (Manual Inhibit) means the signal cannot be changed manually.

6. Alarm Enable (for alarm signals only)

AE - signal is alarm enabled (changes will be reported).

AI - signal is alarm inhibited (changes will not be reported).

D4085 3310/30/35 Display/Keyboard / 15

 Notes for Figure 19 (Continued)

7. Units - units text (for analog signals only), if any units have been defined.

8. Alarm State

For Analog Signals: For Logical Signals:

HH - high-high alarm TA - true alarm
HI - high alarm FA - false alarm
LO - low alarm CA - change-of-state alarm
LL - low-low alarm NA - no alarm
NA - no alarm

! - alarm is unacknowledged

9. Multiple Signal Display

In Read Mode, pressing MULT will display the signal name extension, value, and units for three
signals at one time. These signals include the signal displayed when NEXT was pressed and
the next two signals in the list. Press SNGL [F3] to return to viewing one signal at a time (see
Figure 20).

Figure 20 - Example of MULT Display in READ mode

Signals are shown below as they would appear in SNGL mode.

1) String
SITE.NAME
WEST SUNBURY PUMP STATION
CE ME

2) Analog
TOTAL.FLOW.RATE
1260.578 GALS.
CE MI

3) Logical
FLOW.ALARM
OFF
CE MI AE NA

16 / 3310/30/35 Display/Keyboard D4085

While editing an analog value or digital status, you may see the following messages:

PRESS CLR TO CHANGE

NOT IN MANUAL MODE

The first message is a reminder that the first thing you must do to change an analog value
or digital status is to press CLR.

The second message will appear when the signal cannot be changed because it is not in
manual enable (ME) mode.

To acknowledge an alarm:

Press [ALM ACK].

To change the alarm enable/inhibit status for alarm signals:

Press [ALM I/E] key. (Note: This will only inhibit alarm reporting, and not alarm level
detection.)

SIGNING-OFF

Once you have signed-on, use the [INIT] key at any time to sign-off. When this key has
been pressed, the screen will look like Figure 21. Press YES to sign-off. You are signed-off
when the Identifier Display (Figure 6C) appears.

Figure 21 - Sign Off Display

If you do not want to sign-off, press EXIT to leave the Sign-Off Display.

Once you are signed-on an automatic sign-off will occur if 20 minutes has elapsed since the
last key was pressed.

INTERPRETING ERROR MESSAGES

NO INPUT LISTS

Meaning: This may occur when the MENU function is selected. No input lists were
entered during configuration.

D4085 3310/30/35 Display/Keyboard / 17

Remedy: Values or signal names must be entered on the INPUT terminals of the Key-
board Module using the ACCOL Interactive Compiler (AIC) or ACCOL Batch
Compiler (ABC) (See Step 5, page 8).

UNWIRED INPUT

Meaning: No value has been entered at this INPUT terminal in the ACCOL load.

Remedy: Using the AIC or ABC, enter a valid value.

NON-EXISTENT LIST

Meaning: The list was not found in the load. An invalid signal list number was entered
on the LIST or INPUT terminals.

Remedy: Using the AIC or ABC, enter a valid signal list number on the LIST or INPUT
terminals (See Steps 2 and 5, pages 5 and 8).

NO SCROLL LIST

Meaning: The Scroll Terminal has been left unwired.

Remedy: Use the AIC or ABC to enter a value or signal name on the LIST terminal (See
Step 2, page 3).

EMPTY LIST

Meaning: A valid signal list number has been requested but the signal list is empty.

Remedy: Use the AIC or ABC to create a signal list and/or place the appropriate signal
names into the empty list.

NOT IN MANUAL MODE

Meaning: The signal is manual inhibited (MI) mode.

Remedy: Use the OPER I/E key to change mode to ME.

STRING SIGNAL:

Meaning: User is trying to change a string signal

Remedy: None - String signals cannot be changed with the keyboard.

18 / 3310/30/35 Display/Keyboard D4085

 Figure 22 - Local/Remote 5 X 5 Keyboard

Figure 23 - Remote Only Keyboard

D4085 3310/30/35 Display/Keyboard / 19

 Table 1 - The Keyboard Keys

KEY FUNCTION
Function keys will take on a variety of different functions depending on the
F1, F2, F3,
situation. The function of these keys is listed on the legend line (bottom line) of the
F4
display.
INIT The INIT key is used to terminate the keyboard session and sign-off.
These keys are used to change the value of analog signals in the
0 to 9, -, . CONFIGURATION mode. The 0/OFF and 1/ON keys are used to change the state
of logical signals.
Each press of this key will raise an analog signal value by 1% of the displayed
∆
value or turn a logical signal ON.
Each press of this key will lower an analog signal value by 1% of the displayed
∇
value or turn a logical signal OFF.
ALM I/E Use this key to enable or inhibit alarm signals.
ALM ACK Use this key to acknowledge alarms.
A/M Toggle between AUTO (CE) and MANUAL (CI) with this key.
OPER I/E Toggle between manual inhibit (MI) and enable (ME) with this key.
DEL Use this backspace key to erase digits that have been entered on the keypad.
This key is used to enter new data from the display into the DPC 3330, e.g.,
ENT
password or signal values.

20 / 3310/30/35 Display/Keyboard D4085

 Appendix DKA Issue: 07/05

CW_10 4 X 20 DISPLAY - KEYBOARD ASSEMBLY

For Document D4085

R E Y NOL D S GA S S Y S T EM
L OC K P O R T S T A T I ON
8 RUN S
S I GN ON S CROL L

F1 F2 F3 F4 INIT

7 8 9

ALM ALM
4 5 6 I/E ACK

1 OPER
2 3 A/M I/E
ON
0
DEL ENT
OFF

Bristol Babcock
 Appendix DKA of Document D4085
CW_10 4 X 20 DISPLAY-KEYBOARD ASSEMBLY

TABLE OF CONTENTS
SECTION TITLE PAGE #

Section 1 - INTRODUCTION

1.1 DESCRIPTION............................................................................................................................... 1
1.1.1 Resident D-K Assembly .............................................................................................................. 1

Section 2 - INSTALLATION, OPERATION & SERVICE

2.1 INSTALLATION ............................................................................................................................ 3

2.2 SCREEN ADJUSTMENT .............................................................................................................. 3
2.3 DISPLAY FUNCTION BLOCK DESCRIPTION ......................................................................... 4
2.3.1 DISPLAY Function Block Parameters ...................................................................................... 5
2.4 PREPARING THE ControlWave PROJECT ................................................................................ 5
2.5 USING THE KEYBOARD ............................................................................................................. 6
2.5.1 Scrolling ....................................................................................................................................... 7
2.5.2 Signing-On ................................................................................................................................... 8
2.5.3 Using the Clock Functions.......................................................................................................... 9
2.5.3.1 Changing the Time ................................................................................................................ 10
2.5.3.2 Changing the Date ................................................................................................................. 10
2.5.4 Choosing a Variable List from the List Menu......................................................................... 10
2.5.5 Moving Through a Variable List .............................................................................................. 11
2.5.6 Changing Variable Parameters................................................................................................ 11
2.5.7 Signing-Off................................................................................................................................. 14
2.6 KEYBOARD IDENTIFICATION INFO...................................................................................... 14

D4085 - Appendix DKA Page 0-1 Table Of Contents

 Section 1
INTRODUCTION

1.1 DESCRIPTION

The Display-Keyboard (D-K) Assembly provides a convenient local operator interface. With
this option, the operator can observe and alter certain RTU parameters defined in the
ControlWave Project.

The Display consists of a 4-line, 20 character readout on a 5 x 7 dot matrix LCD screen as
shown in Figure DKA-1. A screen adjustment (contrast) controls the intensity of the
readout. The display presents a variety of menus that allow the user to read or write
parameters, select functions, and create text.

The Keyboard section utilizes 25 keys arranged in a 5 x 5 matrix as shown in the

illustration. When pressed, the keys respond with a soft touch click. The on-board assembly
is built into the RTU and is visible from the front; the extended type is a separate assembly
that is attached to the RTU via a flat cable.

Bristol Babcock Display-Keyboard assemblies provide a built-in, local, user interface for the
ControlWave_10. These assemblies allow an operator or engineer to view and modify
variable values and associated status information, via an ACCOL3 Function Block.
Variables can include inputs, process variables, calculated variables, constants, setpoints,
tuning parameters and outputs used in a measurement or control application. Status bits
include alarm state, alarm acknowledge, control, manual, and questionable data.

Setting up the Display-Keyboard Assembly is a simple matter of configuring a Display

Function Block in the ControlWave Designer project.

1.1.1 Resident D-K Assembly

A resident Display-Keyboard Assembly is secured to the CW_10 RTU via four screws. The
two top captive screws secure the assembly to swileling stand-offs (hinges) which allow the
panel to be swung out of the way to access I/O boards.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.1

 Figure DKA-1 – Display-Keyboard Assembly Identification Drawing

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.2

 Section 2
INSTALLATION & OPERATION

2.1 INSTALLATION

2.1.1 Resident D-K Systems

The Resident Display and Keyboard system is assembled to the RTU and does not require
installation.

Figure DKA-2 – Display & Keyboard Components

2.2 SCREEN ADJUSTMENT

The Screen (Contrast) Adjustment Potentiometer is concealed behind a threaded plug.

(Figure DKA-2). Remove this plug with a socket wrench or similar tool. Use a screwdriver
to turn the Pot. Clockwise rotation of the pot will increase the contrast. When adjustments
are complete, replace the plug and o-ring. The plug must be properly secured to comply
with NEMA 4 installations.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.3

If you're setting up the Keyboard, follow the configuration instructions provided in Section
2.4 of this appendix.

If your Keypboard has already been set up, Section 2.5 will tell you how to use the
Keyboard and interpret the Display.

2.3 DISPLAY FUNCTION BLOCK DESCRIPTION

Keyboard and Display control/configuration are handled by the DISPLAY Function Block.
This function block allows an operator to view/change variable data or to be allowed to
scroll through lists of variable data based upon their login privileges.

In order for the Keyboard and Display to operate, the ControlWave Designer project must
include a properly configured DISPLAY Function Block. Use ControlWave Designer to
configure this function block and assign the parameters according to the four steps covered
in Section 2.4.

Figure DKA-3 - ACCOL3 DISPLAY Function Block Parameters

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.4

2.3.1 DISPLAY Function Block Parameters

Referring to Figure DKA-3, various DISPLAY Function Block Parameters are available.
For information on configuring the Display Function Block, please reference on-line help in
ControlWave Designer.

2.4 PREPARING THE ControlWave PROJECT

In order for the Keyboard and Display to operate, the ControlWave Designer project must
include a properly configured Display Function Block. Once the Keyboard is operating, a
user who has signed on with a password can scroll through the names of variable lists and
choose a list to read or change. Use Up Arrow and Down Arrow keys to select the Username
and use the numeric keys to enter your password. The steps that follow describe how to
configure this function block.

Step 1: Creating the Identifier Display

The Identifier Display is the first display to appear when the Display Function Block is
initialized and begins to execute. This display will look similar to Figure DKA-5. Each of
the first three lines of the display contains the text value of a string variable. These string
variables are created utilizing iaScrnStruct parameters of the Display Function Block (See
Figure DKA-4) and your computer keyboard. Since this is the first display that the user will
see, you may want the display to contain general information such as the node name of the
controller or the process that the controller is monitoring.

The bottom line on the display is called the legend line. It shows which function keys are
currently active and their purpose. Function keys are those keys on the Keypad that are
marked ([F1] through [F4]). Function key assignments are preconfigured and cannot be
changed. Using function keys is described in Section 2.5, Using the Keyboard.

The legend line in Figure DKA-4 shows that the user has two choices: to Log-in (using [F1])
or scroll (using [F2]).

Figure DKA-4 - Creating the Identifier Message

Step 2: Defining a Scroll List

Once the Keyboard is operating properly, you can automatically scroll through a list of
variables created via DISPLAY Function Block Parameters iiList2Scroll and iiListMode.
Scrolling can be done without entering a password. The variables in the list are displayed
one at a time and in the same order in which they were entered in the variable list.

Later, we'll discuss other variable lists that can be accessed with the Keyboard. To
distinguish this list from others, let's call this variable list the Scroll List.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.5

Enter the number of a variable list to be scrolled. This variable list becomes the Scroll List.
The Scroll List can contain different types of variables (that is, logical, analog and string).
You can create a specific scroll variable list or use any list in the ControlWave Project.

Each variable in the Scroll List will be displayed for the number of seconds defined by the
iiScrollTime parameter. If you don't specify a time for this parameter, the hold time will be
two seconds. If you signed-on and then started scrolling you will be signed-off in 20 minutes
if no keys are pressed. If you don’t want to automatically stop scrolling after 20 minutes,
sign-off (INIT key) before starting scrolling.

Step 3: Assigning Passwords

A valid RTU username/password combination must be entered to go beyond the initial

displays. Passwords can be any combination of numbers up to 16 digits in length, from
0000000000000000 to 9999999999999999. If none are specified, the default values are
system for User-name and 666666 for Password (read/write access).

Step 4: Status Information

Enter a variable name on the odiStatus terminal.

See On Line Help in ControlWave Designer for Status Values.

The next section describes how to use the Keyboard to access variable information.

2.5 USING THE KEYBOARD

The Identifier Display is the starting point from which you can go to other displays. It
shows an identification message and the words Login and Scroll at the bottom of the screen
(see Note 1). The identification message may contain the name of the controller, the plant
equipment it is monitoring, or the variables you can expect to see when you use this
display.

Note 1 : If your display shows something else, press the [F4] key until you see the words
Login and Scroll on the bottom line.

If your screen is blank, turn the Screen (Contrast) Adjustment Poentiometer

clockwise. This Pot. is located behind a Plug (see Figure DKA-2). If no letters
appear, the controller has not been programmed properly to operate the Keyboard.

The words Login and Scroll at the bottom of the screen are on the legend line. It tells you
which function keys (that is, key [F1] through [F4]) are active and their purpose at that
time.

Up to four legends can appear on the legend line. The legend on the far left corresponds to
the function of the [F1] key. The assignment for the [F4] key is on the far right. Keys [F2]
and [F3] are described to the left and right of center. When no legend appears, that function
key is not active at that time. For example, in Figure DKA-5 only [F1] and [F2] are active.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.6

 Figure DKA-5 - The Identifier Display

From the Identifier Display, you have two choices. Pressing [F1] will allow you to sign-on if
you have a password. By pressing [F2] you can activate automatic scrolling through a list of
variables.

Figure DKA-6 - Identifier Display Legends and Corresponding Keypad Alignment

for 25 Button Membrane Key Matrix Keyboard System

2.5.1 Scrolling

To begin automatic scrolling, press [F2] from the Identifier Display (Figure DKA-6).
Variable in-formation will appear on the screen and remain there for 1 to 30 seconds
(default = 2 seconds). The variable name appears on the first line. The variable value
appears on the second line and status information appears on the third line. An example is
shown in Figure DKA-7.

When all variables in the list have been displayed, they will be shown again in the same
order. This is called Single Variable Mode.

Pressing Mlti [F2] activates Multiple Variable Mode. Multiple Variable Mode displays up to
three (3) variables and their values on the screen simultaneously. Pressing Sngl [F2]
terminates Multiple Variable Mode and returns you to Single Variable Mode.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.7

 Figure DKA-7 - Scrolling

Press HOLD [F1] to halt scrolling. Changing variable values will continue to be displayed.

Press GO [F1] to resume scrolling.

Press EXIT [F4] to return to the Identifier Display (Figure DKA-5).

2.5.2 Signing-On

To access the List Menu, you must first sign-on with a proper password. From the
Identifier Display (Figure DKA-6), press [F1]. The screen will look like Figure DKA-8A or
DKA-8C. If the display looks like Figure DKA-8C:

Someone else has already signed on. Go to the paragraph below that starts "Once you
have successfully signed on,…".

If the display looks like Figure DKA-8A:

Select the Username (default = system) by using the Up and Down Arrow Keys. If the
Username system is displayed and no other Username is available (i.e., no others have
been assigned), press [ENTER].

Enter a password using the 0 to 9 keys. For security, asterisks will appear as you enter
the digits. If you make a mistake, press [F1] and try again (or use the delete key to
delete the previously pressed key action). The default password is 666666 (used when a
password is not known or no password has been assigned). After typing the password,
press [ENTER].

If your password is not recognized, the asterisks will be erased after you press
[ENTER]. Check your password and try again.

Once the correct password has been entered, the display will look like Figure DKA-8C.

When the second line shows READ/WRITE, you can read and write variable parameters.
When it shows READ ONLY you cannot change variable parameters. You are only permit-
ted to read variable information. If your display shows READ ONLY and you want to
change variable values, sign-off (press the [INIT] key) and log on with a username and
password that provides Read/Write privileges.

Once you have successfully signed on, the legend line will show that you have four options.
D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.8
You can view and change the time and date of the local clock, access more variable lists,
Scroll, or return to the Identifier Display. Use function keys F1 through F4 to select the
next menu (F1 = Clock, F2 = Menu, F3 = Scroll list & F4 = Exit). Let's start by setting the
local clock.

Figure DKA-8 - Logging On

2.5.3 Using the Clock Functions

From the Logged-On Display (Figure DKA-8C), press [F1]. The screen will show the present
date and time and will look like Figure DKA-9. Follow the instructions below to change the
time or date. When you're finished, press [F4] to exit.

Today's date is shown in the first line in the format month/day/year.

The current time is shown in the form of hours:minutes:seconds.

Figure DKA-9 - Clock Display

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.9
2.5.3.1 Changing the Time

From the display shown in Figure DKA-9, press Time [F2]. Colons (:) will appear on the
third line. Enter the new time there and press [ENTER]. Valid times range from 00:00:00 to
23:59:59. Invalid entries will be ignored. The display will be updated to show the new time.

Figure DKA-10 - Time Set Display

If you make a mistake while entering the new time, use [DEL] to backspace and delete one
character at a time.

2.5.3.2 Changing the Date

From the clock display (Figure DKA-9, press [F1]. Slash marks (/) will appear on the third
line. Enter the new date there and press [ENTER].

Figure DKA-11 - Date Set Display

If you make a mistake while entering the new date, use [DEL] to back space and delete one
character at a time. Press [F4] to return to the Logged-On Display (Figure DKA-8C).

2.5.4 Choosing a Variable List from the List Menu

The List Menu is another area where variable information can be seen. As explained earlier
in this section, your first opportunity to read variable information is by choosing the
SCROLL function from the Initial Display. The variable name and value are presented
from the Scroll List. This function is available to all users even without signing-on.

The List Menu will show other groups of variable which you can choose to read. This in-
formation will be more detailed than the Scroll List.

To get to the List Menu, choose MENU (press [F2]) from the Logged-On Display (Figure
DKA-8C).

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.10

 Figure DKA-12 - Using the List Menu Display

The first variable list number in the menu will appear on the second line.

Press PREV (F1) and NEXT (F2) to see the other variable lists that are available in the List
Menu. You can also use the Up and Down Arrow Keys to scroll through the various lists. To
move directly to a list, enter the list number, then press [ENTER].

2.5.5 Moving Through a Variable List

After READ (F1) or WRITE (F2) has been pressed, the display will show the first variable
in the list. An example is shown in Figure DKA-13. Each time NEXT (F2) is pressed; the
display will show the next variable in the list. PREV (F1) will show the previous variable.
You can also use the Up and Down Arrow Keys to move through a list.

Automatic wraparound occurs in either direction. When you reach the end of the list, [F1]
will display the first variable again. At the top of the list, [F2] will display the last variable.

2.5.6 Changing Variable Parameters

From Figure DKA-12, you can change variable parameters by pressing F2 [Write]. Then
follow the directions summarized below (see Note 2).

Note 2: If your display does not contain the legend Write in the legend line, your password
will only allow you to read variables. If you want to change variable values at this
time, you must first log-off and then log-on using the correct password. See your
Systems Engineer for the correct password.

Before making any changes, first check the variable inhibit status field (See Figure DKA-
13). When the display shows ME (manual enable) you can change variable parameters.
When it shows MI (manual inhibit), you cannot alter the parameters of this variable. If the
field indicates MI, press the OPER I/E key to change it to ME.

To change an analog value:

Press CHNG (F3) to clear the third line. Use the number keys 0 through 9 to enter the
new value. The minus sign and period are also permitted. Press [ENTER].

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.11

 If you make a mistake, press CHNG (F3) and enter the number again or use the [DEL]
key to erase a character.

Another way to enter new values is by using the arrow up and arrow down keys (located
below the [F3] key and left of the [INIT] key). These keys will raise and lower the value
by 1% of the displayed amount.

To change the status of a logical variable:

Press CHNG (F3), then use either the down and up arrow keys or the [0/OFF] and
[1/ON] keys to change the state of a logical variable. If the [0/OFF] and [1/ON] keys are
used, you must also press [ENTER].

Figure DKA-13 - Interpreting Variable Information

Notes for Figure DKA-13

1. Variable Name (Example 1: @GV.FLOW_RATE) (Example 2: @GV.TOTAL_FLOW_RATE)

2. Value - analog value, string value, or logical value. Values which cannot fit in this field will be
shown as asterisks.

Analog values are displayed in floating point format, for example, 0.0125, 99.627, and 1287.66.
When the value cannot be shown in floating point format, scientific format is used
(1.287668E+10 or 1.25E-02 for example).

3. Questionable Data Status - for analog variables, column 1 will be clear if the status is valid. It
will display a question mark if the status is questionable.

4. Variable Inhibit Status

CE (Control Enable) means this variable can be updated by the ControlWave project.
CI (Control Inhibit) means the variable cannot be updated by the ControlWave project.
ME (Manual Enable) means the variable can be changed manually.
MI (Manual Inhibit) means the variable cannot be changed manually.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.12

 Notes for Figure DKA-13 (Continued)

5. Alarm Enable (for alarm variables only)

AE - variable is alarm enabled (changes will be reported).

AI - variable is alarm inhibited (changes will not be reported).

6. Alarm State

For Analog Variables: For Logical Variables:

HH - high-high alarm TA - true alarm
HI - high alarm FA - false alarm
LO - low alarm CA - change-of-state alarm
LL - low-low alarm

! - alarm is unacknowledged

7 Multiple Signal Display

In Read Mode, pressing MULT (F3) will display the variable name extension, value, and units
for three variables at one time. These variables include the variable displayed when NEXT (F2)
was pressed and the next two variables in the list. Press SNGL [F3] to return to viewing one
variable at a time (see Figure DKA-13A).

Figure DKA-13A - Example of MULT Display in READ Mode

Variables are shown below as they would appear in SNGL mode.

1) String
SITE_NAME
WEST SUNBURY PUMP STATION
CE ME

2) Analog
TOTAL_FLOW_RATE
1260.578
CE MI

3) Logical
FLOW_ALARM
OFF
CE MI AE NA
To acknowledge an alarm:

Press [ALM ACK].

To change the alarm enable/inhibit status for alarm variables:

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.13

 Press [ALM I/E] key. (Note: This will only inhibit alarm reporting, and not alarm level
detection.)

2.5.7 Signing-Off

Once you have logged-on, use the [INIT] key at any time to log-off. When this key has been
pressed, the screen will look like Figure DKA-14. Press Yes (F1) to sign-off. You are signed-
off when the Identifier Display (Figure DKA-5) appears.

If you do not want to log-off, press Exit (F4) to leave the Log-Off Display.

Once you are signed-on an automatic sign-off will occur if 20 minutes has elapsed since the
last key was pressed.

Figure DKA-14 - Log-Off Display

2.6 KEYBOARD IDENTIFICATION INFO.

Figure DKA-15 - 25 Button Keyboard

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.14

 Table DKA-1 - 25 Button Keyboard Keys

KEY FUNCTION
Function keys will take on a variety of different functions depending on the
F1, F2, F3,
situation. The function of these keys is listed on the legend line (bottom line) of the
F4
display.
INIT The INIT key is used to terminate the keyboard session and sign-off.
These keys are used to change the value of analog variables in the
0 to 9, −, • CONFIGURATION mode. The 0/OFF and 1/ON keys are used to change the state
of logical variables.
Each press of this key will raise an analog variable value by 1% of the displayed
∆
value or turn a logical variable ON.
Each press of this key will lower an analog variable value by 1% of the displayed
∇
value or turn a logical variable OFF.
ALM I/E Use this key to enable or inhibit alarm variables.
ALM ACK Use this key to acknowledge alarms.
A/M Toggle between AUTO (CE) and MANUAL (CI) with this key.
OPER I/E Toggle between manual inhibit (MI) and enable (ME) with this key.
DEL Use this backspace key to erase digits that have been entered on the keypad.
This key is used to enter new data from the display into the controller, e.g.,
ENT
password or variable values.

D4085 - Appendix DKA CW_10 4-20 Display-Keyboard / Pg.15

BLANK PAGE
 Appendix DKB Issue: 07/05

CW_30 4 X 20 DISPLAY - KEYBOARD ASSEMBLY

For Document D4085

Local F1

7
F2

8
F3

9
F4 INIT

ALM ALM
4 5 6 I/E ACK

{
1 OPER
R E Y NOL D S GA S S Y S T EM 2 3 A/M I/E
ON
L OC K P O R T S T A T I ON
8 RUN S 0
DEL ENT
S I GN ON S CROL L OFF

R E Y NOL D S GA S S Y S T EM
L OC K P O R T S T A T I ON
8 RUN S
S I GN ON S CROL L

F1 F2 F3 F4 INIT

7 8 9

ALM ALM
4 5 6 I/E ACK

1 OPER
2 3 A/M I/E
ON
0
DEL ENT
OFF

BRISTOL
BABCOCK

Remote
Bristol Babcock
 Appendix DKB
CW_30 4 X 20 DISPLAY-KEYBOARD ASSEMBLY

TABLE OF CONTENTS
SECTION TITLE PAGE #

Section 1 - INTRODUCTION

1.1 DESCRIPTION............................................................................................................................... 1
1.1.1 Resident (Local) D-K Assembly.................................................................................................. 1
1.1.2 Extended D-K Assembly ............................................................................................................. 1

Section 2 - INSTALLATION, OPERATION & SERVICE

2.1 INSTALLATION ............................................................................................................................ 3

2.1.1 Resident (Local) D-K Assembly.................................................................................................. 3
2.1.2 Extended D-K Assembly ............................................................................................................. 3
2.2 SCREEN ADJUSTMENT .............................................................................................................. 4
2.3 DISPLAY FUNCTION BLOCK DESCRIPTION ......................................................................... 4
2.3.1 DISPLAY Function Block Parameters ...................................................................................... 5
2.4 PREPARING THE ControlWave PROJECT ................................................................................ 5
2.5 USING THE KEYBOARD ............................................................................................................. 6
2.5.1 Scrolling ....................................................................................................................................... 7
2.5.2 Signing-On ................................................................................................................................... 8
2.5.3 Using the Clock Functions.......................................................................................................... 9
2.5.3.1 Changing the Time ................................................................................................................ 10
2.5.3.2 Changing the Date ................................................................................................................. 10
2.5.4 Choosing a Variable List from the List Menu......................................................................... 10
2.5.5 Moving Through a Variable List .............................................................................................. 11
2.5.6 Changing Variable Parameters................................................................................................ 11
2.5.7 Signing-Off................................................................................................................................. 14
2.6 KEYBOARD IDENTIFICATION INFO...................................................................................... 14

D4085 - Appendix DKB Page 0-1 Table Of Contents

 Section 1
INTRODUCTION

1.1 DESCRIPTION

The Display-Keyboard (D-K) Assembly provides a convenient local operator interface. With
this option, the operator can observe and alter certain DPC parameters defined in the
ControlWave Project.

The Display consists of a 4-line, 20 character readout on a 5 x 7 dot matrix LCD screen as
shown in Figures DKB-1 & DKB-2. A screen adjustment (contrast) controls the intensity of
the readout. The display presents a variety of menus that allow the user to read or write
parameters, select functions, and create text.

The Keyboard section utilizes 25 keys arranged in a 5 x 5 matrix as shown in the

illustration. When pressed, the keys respond with a soft touch click. The on-board assembly
is built into the DPC and is visible from the front; the extended type is a separate assembly
that is attached to the DPC via a flat cable.

Bristol Babcock Display-Keyboard assemblies provide a built-in, local, user interface for the
ControlWave_30. These assemblies allow an operator or engineer to view and modify
variable values and associated status information, via an ACCOL3 Function Block.
Variables can include inputs, process variables, calculated variables, constants, setpoints,
tuning parameters and outputs used in a measurement or control application. Status bits
include alarm state, alarm acknowledge, control, manual, and questionable data.

Setting up the Display-Keyboard Assembly is a simple matter of configuring a Display

Function Block in the ControlWave Designer project.

1.1.1 Resident (Local) D-K Assembly

The resident (local) Display and Keyboard mount at the front of the chassis and are visible
with the cover in place on DPCs with plastic covers. For DPCs furnished in NEMA-4
enclosures, a front window provides display visibility.

The complete on-board assembly is mounted on a hinged panel. A front view of this
assembly is shown in Figure DKB-1. Loosening the captive screw above the Keyboard
allows the panel to be swung out of the way to access other components.

1.1.2 Extended D-K Assembly

The hardware of the extended D-K Assembly has the arrangement shown in Figure DKB-3.
This version provides a Resident Module (not shown) in the DPC connected by a ribbon
cable to a Remote (extended D-K Assembly).

The Resident Module is wired to a connector that is accessible through an opening in the
DPC cover. The Resident Module uses the same interface board assembly; however, the
Display and Keypad boards are replaced by a Buffer Board having the appropriate drivers
and interface for the Remote Unit (no PC boards are illustrated).

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.1

 Figure DKB-1 – Resident (Local) 4 X 20 Display/Keyboard Assembly

Figure DKB-2 –Remote Unit of Extended D-K System

The Remote Unit of the Extended D-K System is contained in a metal housing having
appropriate openings for the display and keyboard (Figure DKB-2). The screen adjustment
(contrast) is concealed behind a threaded plug. This plug and its o-ring must be replaced
and secured when adjustments are complete.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.2

 Section 2
INSTALLATION & OPERATION

2.1 INSTALLATION

2.1.1 Resident (Local) D-K Systems

The Resident (Local) Display-Keyboard system is assembled to the DPC and does not
require installation.

2.1.2 Extended D-K System

The Remote Unit connects to the CW_30 DPC via a 10-foot, 50-conductor ribbon cable
(Figure DKB-2). One end of the cable plugs into a receptacle at the front of the DPC, and
the other end into a connector at the back of the Display Unit.

Note that the Remote Unit is open at the back and uses the mounting surface as a back
plate. The Remote Unit is designed to mount against a surface such as a cabinet wall. The
cabinet must have a cutout to accommodate the ribbon cable. The unit cutout and drill
dimensions are given in Figure DKB-3.

Figure DKB-3 - Extended Display Cable Connections and Mounting Dimensions

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.3
When attaching the Remote Unit to the mounting surface, all eight nuts and washers
(supplied) must be installed on the threaded studs. All nuts must be tightened sufficiently
so that there is a good seal between the rear gasket and the mounting surface. The
threaded plug and o-ring that provide access to the screen adjustment must also be
installed and secured.

2.2 SCREEN ADJUSTMENT

The Screen (Contrast) Adjustment Potentiometer is concealed behind a threaded plug on

Remote Units (Figure DKB-2). Remove this plug with a socket wrench or similar tool. On
Local Units, the Screen Adjustment Poentiometer is situated to the left of the Keyboard
Assembly (Figure DKB-1). Use a screwdriver to turn the Pot. Clockwise rotation of the pot
will increase the contrast. When adjustments to a Remote Unit are complete, replace the
plug and o-ring. The plug must be properly secured to comply with NEMA 4 installations.

If you're setting up the Keyboard, follow the configuration instructions provided in Section
2.4 of this appendix.

If your Keyboard has already been set up, Section 2.5 will tell you how to use the Keyboard
and interpret the Display.

2.3 DISPLAY FUNCTION BLOCK DESCRIPTION

Keyboard and Display control/configuration are handled by the DISPLAY Function Block.
This function block allows an operator to view/change variable data or to be allowed to
scroll through lists of variable data based upon their login privileges.

In order for the Keyboard and Display to operate, the ControlWave Designer project must
include a properly configured DISPLAY Function Block. Use ControlWave Designer to
configure this function block and assign the parameters according to the four steps covered
in Section 2.4.

Figure DKB-4 - ACCOL3 DISPLAY Function Block Parameters

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.4

2.3.1 DISPLAY Function Block Parameters

Referring to Figure DKB-4, various DISPLAY Function Block Parameters are available.
For information on configuring the Display Function Block, please reference on-line help in
ControlWave Designer.

2.4 PREPARING THE ControlWave PROJECT

In order for the Keyboard and Display to operate, the ControlWave Designer project must
include a properly configured Display Function Block. Once the Keyboard is operating, a
user who has signed on with a password can scroll through the names of variable lists and
choose a list to read or change. Use Up Arrow and Down Arrow keys to select the Username
and use the numeric keys to enter your password. The steps that follow describe how to
configure this function block.

Step 1: Creating the Identifier Display

The Identifier Display is the first display to appear when the Display Function Block is
initialized and begins to execute. This display will look similar to Figure DKB-6. Each of
the first three lines of the display contains the text value of a string variable. These string
variables are created utilizing iaScrnStruct parameters of the Display Function Block (See
Figure DKB-4) and your computer keyboard. Since this is the first display that the user will
see, you may want the display to contain general information such as the node name of the
controller or the process that the controller is monitoring.

The bottom line on the display is called the legend line. It shows which function keys are
currently active and their purpose. Function keys are those keys on the Keyboard that are
marked ([F1] through [F4]). Function key assignments are preconfigured and cannot be
changed. Using function keys is described in Section 2.5, Using the Keyboard.

The legend line in Figure DKB-5 shows that the user has two choices: to Log-in (using [F1])
or scroll (using [F2]).

Figure DKB-5 - Creating the Identifier Message

Step 2: Defining a Scroll List

Once the Keyboard is operating properly, you can automatically scroll through a list of
variables created via DISPLAY Function Block Parameters iiList2Scroll and iiListMode.
Scrolling can be done without entering a password. The variables in the list are displayed
one at a time and in the same order in which they were entered in the variable list.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.5

Later, we'll discuss other variable lists that can be accessed with the Keybaord. To
distinguish this list from others, let's call this variable list the Scroll List.

Enter the number of a variable list to be scrolled. This variable list becomes the Scroll List.
The Scroll List can contain different types of variables (that is, logical, analog and string).
You can create a specific scroll variable list or use any list in the ControlWave Project.

Each variable in the Scroll List will be displayed for the number of seconds defined by the
iiScrollTime parameter. If you don't specify a time for this parameter, the hold time will be
two seconds. If you signed-on and then started scrolling you will be signed-off in 20 minutes
if no keys are pressed. If you don’t want to automatically stop scrolling after 20 minutes,
sign-off (INIT key) before starting scrolling.

Step 3: Assigning Passwords

A valid RTU username/password combination must be entered to go beyond the initial

displays. Passwords can be any combination of numbers up to 16 digits in length, from
0000000000000000 to 9999999999999999. If none are specified, the default values are
system for User-name and 666666 for Password (read/write access).

Step 4: Status Information

Enter a variable name on the odiStatus terminal.

See On Line Help in ControlWave Designer for Status Values.

The next section describes how to use the Keypad to access variable information.

2.5 USING THE KEYBOARD

The Identifier Display is the starting point from which you can go to other displays. It
shows an identification message and the words Login and Scroll at the bottom of the screen
(see Note 1). The identification message may contain the name of the controller, the plant
equipment it is monitoring, or the variables you can expect to see when you use this
display.

Note 1 : If your display shows something else, press the [F4] key until you see the words
Login and Scroll on the bottom line.

If your screen is blank, turn the Screen Adjustment Poentiometer clockwise. This
Pot. is located to the left of the Keypboard on Local Units (see Figure DKB-1) or
behind a Plug on Remote Units (see Figure DKB-2). If no letters appear, the control-
ler has not been programmed properly to operate the keypad.

The words Login and Scroll at the bottom of the screen are on the legend line. It tells you
which function keys (that is, key [F1] through [F4]) are active and their purpose at that
time.

Up to four legends can appear on the legend line. The legend on the far left corresponds to
the function of the [F1] key. The assignment for the [F4] key is on the far right. Keys [F2]
and [F3] are described to the left and right of center. When no legend appears, that function
key is not active at that time. For example, in Figure DKB-6 only [F1] and [F2] are active.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.6

 Figure DKB-6 - The Identifier Display

From the Identifier Display, you have two choices. Pressing [F1] will allow you to sign-on if
you have a password. By pressing [F2] you can activate automatic scrolling through a list of
variables.

Figure DKB-7 - Identifier Display Legends and Corresponding Keypad Alignment

for 25 Button Membrane Key Matrix Keyboard System

2.5.1 Scrolling

To begin automatic scrolling, press [F2] from the Identifier Display (Figure DKB-7).
Variable in-formation will appear on the screen and remain there for 1 to 30 seconds
(default = 2 seconds). The variable name appears on the first line. The variable value
appears on the second line and status information appears on the third line. An example is
shown in Figure DKB-8.

When all variables in the list have been displayed, they will be shown again in the same
order. This is called Single Variable Mode.

Pressing Mlti [F2] activates Multiple Variable Mode. Multiple Variable Mode displays up to
three (3) variables and their values on the screen simultaneously. Pressing Sngl [F2]
terminates Multiple Variable Mode and returns you to Single Variable Mode.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.7

 Figure DKB-8 - Scrolling

Press HOLD [F1] to halt scrolling. Changing variable values will continue to be displayed.

Press GO [F1] to resume scrolling.

Press EXIT [F4] to return to the Identifier Display (Figure DKB-6).

2.5.2 Signing-On

To access the List Menu, you must first sign-on with a proper password. From the Identifier
Display (Figure DKB-7), press [F1]. The screen will look like Figure DKB-9A or DKB-9C. If
the display looks like Figure DKB-9C:

Someone else has already signed on. Go to the paragraph below that starts "Once you
have successfully signed on,…".

If the display looks like Figure DKB-9A:

Select the Username (default = system) by using the Up and Down Arrow Keys. If the
Username system is displayed and no other Username is available (i.e., no others have
been assigned), press [ENTER].

Enter a password using the 0 to 9 keys. For security, asterisks will appear as you enter
the digits. If you make a mistake, press [F1] and try again (or use the delete key to
delete the previously pressed key action). The default password is 666666 (used when a
password is not known or no password has been assigned). After typing the password,
press [ENTER].

If your password is not recognized, the asterisks will be erased after you press
[ENTER]. Check your password and try again.

Once the correct password has been entered, the display will look like Figure DKB-9C.

When the second line shows READ/WRITE, you can read and write variable parameters.
When it shows READ ONLY you cannot change variable parameters. You are only permit-
ted to read variable information. If your display shows READ ONLY and you want to
change variable values, sign-off (press the [INIT] key) and log on with a username and
password that provides Read/Write privileges.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.8

Once you have successfully signed on, the legend line will show that you have four options.
You can view and change the time and date of the local clock, access more variable lists,
Scroll, or return to the Identifier Display. Use function keys F1 through F4 to select the
next menu (F1 = Clock, F2 = Menu, F3 = Scroll list & F4 = Exit). Let's start by setting the
local clock.

Figure DKB-9 - Logging On

2.5.3 Using the Clock Functions

From the Logged-On Display (Figure DKB-9C), press [F1]. The screen will show the present
date and time and will look like Figure DKB-10. Follow the instructions below to change
the time or date. When you're finished, press [F4] to exit.

Today's date is shown in the first line in the format month/day/year.

The current time is shown in the form of hours:minutes:seconds.

Figure DKB-10 - Clock Display

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.9
2.5.3.1 Changing the Time

From the display shown in Figure DKB-10, press Time [F2]. Colons (:) will appear on the
third line. Enter the new time there and press [ENTER]. Valid times range from 00:00:00 to
23:59:59. Invalid entries will be ignored. The display will be updated to show the new time.

Figure DKB-11 - Time Set Display

If you make a mistake while entering the new time, use [DEL] to backspace and delete one
character at a time.

2.5.3.2 Changing the Date

From the clock display (Figure DKB-10, press [F1]. Slash marks (/) will appear on the third
line. Enter the new date there and press [ENTER].

Figure DKB-12 - Date Set Display

If you make a mistake while entering the new date, use [DEL] to back space and delete one
character at a time. Press [F4] to return to the Logged-On Display (Figure DKB-9C).

2.5.4 Choosing a Variable List from the List Menu

The List Menu is another area where variable information can be seen. As explained earlier
in this section, your first opportunity to read variable information is by choosing the
SCROLL function from the Initial Display. The variable name and value are presented
from the Scroll List. This function is available to all users even without signing-on.

The List Menu will show other groups of variable which you can choose to read. This in-
formation will be more detailed than the Scroll List.

To get to the List Menu, choose MENU (press [F2]) from the Logged-On Display (Figure
DKB-9C).

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.10

 Figure DKB-13 - Using the List Menu Display

The first variable list number in the menu will appear on the second line.

Press PREV (F1) and NEXT (F2) to see the other variable lists that are available in the List
Menu. You can also use the Up and Down Arrow Keys to scroll through the various lists. To
move directly to a list, enter the list number, then press [ENTER].

2.5.5 Moving Through a Variable List

After READ (F1) or WRITE (F2) has been pressed, the display will show the first variable
in the list. An example is shown in Figure DKB-14. Each time NEXT (F2) is pressed; the
display will show the next variable in the list. PREV (F1) will show the previous variable.
You can also use the Up and Down Arrow Keys to move through a list.

Automatic wraparound occurs in either direction. When you reach the end of the list, [F1]
will display the first variable again. At the top of the list, [F2] will display the last variable.

2.5.6 Changing Variable Parameters

From Figure DKB-13, you can change variable parameters by pressing F2 [Write]. Then
follow the directions summarized below (see Note 2).

Note 2: If your display does not contain the legend Write in the legend line, your password
will only allow you to read variables. If you want to change variable values at this
time, you must first log-off and then log-on using the correct password. See your
Systems Engineer for the correct password.

Before making any changes, first check the variable inhibit status field (See Figure DKB-
14). When the display shows ME (manual enable) you can change variable parameters.
When it shows MI (manual inhibit), you cannot alter the parameters of this variable. If the
field indicates MI, press the OPER I/E key to change it to ME.

To change an analog value:

Press CHNG (F3) to clear the third line. Use the number keys 0 through 9 to enter the
new value. The minus sign and period are also permitted. Press [ENTER].

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.11

 If you make a mistake, press CHNG (F3) and enter the number again or use the [DEL]
key to erase a character.

Another way to enter new values is by using the arrow up and arrow down keys (located
below the [F3] key and left of the [INIT] key). These keys will raise and lower the value
by 1% of the displayed amount.

To change the status of a logical variable:

Press CHNG (F3), then use either the down and up arrow keys or the [0/OFF] and
[1/ON] keys to change the state of a logical variable. If the [0/OFF] and [1/ON] keys are
used, you must also press [ENTER].

Figure DKB-14 - Interpreting Variable Information

Notes for Figure DKB-14

1. Variable Name (Example 1: @GV.FLOW_RATE) (Example 2: @GV.TOTAL_FLOW_RATE)

2. Value - analog value, string value, or logical value. Values which cannot fit in this field will be
shown as asterisks.

Analog values are displayed in floating point format, for example, 0.0125, 99.627, and 1287.66.
When the value cannot be shown in floating point format, scientific format is used
(1.287668E+10 or 1.25E-02 for example).

3. Questionable Data Status - for analog variables, column 1 will be clear if the status is valid. It
will display a question mark if the status is questionable.

4. Variable Inhibit Status

CE (Control Enable) means this variable can be updated by the ControlWave project.
CI (Control Inhibit) means the variable cannot be updated by the ControlWave project.
ME (Manual Enable) means the variable can be changed manually.
MI (Manual Inhibit) means the variable cannot be changed manually.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.12

 Notes for Figure DKB-14 (Continued)

5. Alarm Enable (for alarm variables only)

AE - variable is alarm enabled (changes will be reported).

AI - variable is alarm inhibited (changes will not be reported).

6. Alarm State

For Analog Variables: For Logical Variables:

HH - high-high alarm TA - true alarm
HI - high alarm FA - false alarm
LO - low alarm CA - change-of-state alarm
LL - low-low alarm

! - alarm is unacknowledged

7 Multiple Signal Display

In Read Mode, pressing MULT (F3) will display the variable name extension, value, and units
for three variables at one time. These variables include the variable displayed when NEXT (F2)
was pressed and the next two variables in the list. Press SNGL [F3] to return to viewing one
variable at a time (see Figure DKB-14A).

Figure DKB-14A - Example of MULT Display in READ Mode

Variables are shown below as they would appear in SNGL mode.

1) String
SITE_NAME
WEST SUNBURY PUMP STATION
CE ME

2) Analog
TOTAL_FLOW_RATE
1260.578
CE MI

3) Logical
FLOW_ALARM
OFF
CE MI AE NA
To acknowledge an alarm:

Press [ALM ACK].

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.13

To change the alarm enable/inhibit status for alarm variables:

Press [ALM I/E] key. (Note: This will only inhibit alarm reporting, and not alarm level
detection.)

2.5.7 Signing-Off

Once you have logged-on, use the [INIT] key at any time to log-off. When this key has been
pressed, the screen will look like Figure DKB-15. Press Yes (F1) to sign-off. You are signed-
off when the Identifier Display (Figure DKB-6) appears.

If you do not want to log-off, press Exit (F4) to leave the Log-Off Display.

Once you are signed-on an automatic sign-off will occur if 20 minutes has elapsed since the
last key was pressed.

Figure DKB-15 - Log-Off Display

2.6 KEYBOARD IDENTIFICATION INFO.

Figure DKB-16 - 25 Button Keyboard

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.14
 Table DKB-1 - 25 Button Keyboard Keys

KEY FUNCTION
Function keys will take on a variety of different functions depending on the
F1, F2, F3,
situation. The function of these keys is listed on the legend line (bottom line) of the
F4
display.
INIT The INIT key is used to terminate the keyboard session and sign-off.
These keys are used to change the value of analog variables in the
0 to 9, −, • CONFIGURATION mode. The 0/OFF and 1/ON keys are used to change the state
of logical variables.
Each press of this key will raise an analog variable value by 1% of the displayed
∆
value or turn a logical variable ON.
Each press of this key will lower an analog variable value by 1% of the displayed
∇
value or turn a logical variable OFF.
ALM I/E Use this key to enable or inhibit alarm variables.
ALM ACK Use this key to acknowledge alarms.
A/M Toggle between AUTO (CE) and MANUAL (CI) with this key.
OPER I/E Toggle between manual inhibit (MI) and enable (ME) with this key.
DEL Use this backspace key to erase digits that have been entered on the keypad.
This key is used to enter new data from the display into the controller, e.g.,
ENT
password or variable values.

D4085 - Appendix DKB CW_30 4-20 Display/Keyboard / Pg.15

BLANK PAGE
 READER RESPONSE FORM

Please help us make our documentation more useful to you! If you have a complaint, a
suggestion, or a correction regarding this manual, please tell us by mailing this page with your
comments. It's the only way we know we're doing our job by giving you correct, complete, and
useful documentation.

DOCUMENT NUMBER: D4085

TITLE: DISPLAY/KEYBOARD ASSEMBLIES for RTU 3310, DPC 3330 & DPC 3335 User
Manual
ISSUE DATE: AUG., 2005
COMMENT/COMPLAINT:

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

Mail this page to:

Bristol Babcock Inc.
1100 Buckingham Street
Watertown, CT 06795
Attn: Technical Publications Group, Dept. 315
 Bristol Babcock
1100 Buckingham Street
Watertown, CT 06795
Phone: +1 (860) 945-2200
Fax: +1 (860) 945-2213
Website: www.bristolbabcock.com

U.S.A. Locations:
Northern Region Gulf Coast Region Western Region Southeast Region
Bristol Babcock Inc. Bristol Babcock Inc. Bristol Babcock Inc. Bristol Babcock Inc.
1100 Buckingham Street 2000 Governor's Circle 1609 South Grove Avenue 317 S. North Lake Blvd.
Watertown, CT 06795 Suite F Suites 106 & 107 Suite 1016
Phone: +1 (860) 945-2381 Houston, TX 77092-8731 Ontario, CA 91761 Altamonte Springs, FL 32701
Fax: +1 (860) 945-2525 Phone: +1 (713) 685-6200 Phone: +1 (909) 923-8488 Phone: +1 (407) 740-7084
Fax: +1 (713) 681-7331 Fax: +1 (909) 923-8988 Fax: +1 (407) 629-2106

Helicoid Instruments Central Region Rocky Mountain Region Communications

1100 Buckingham Street Bristol Babcock Inc. Bristol Babcock Inc. Technology Group
Watertown, CT 06795 300 North Coit Road 906 San Juan Blvd., Suite A Bristol Babcock Inc.
Phone: +1 (860) 945-2218 Suite 1300 Farmington, NM 87401 317 S. North Lake Blvd.
Fax: +1 (860) 945-2213 Richardson, TX 75080 Phone: +1 (505) 320-5046 Suite 1016
Phone: +1 (972) 238-8935 Fax: +1 (505) 327-3273 Altamonte Springs, FL 32701
Fax: +1 (972) 238-8198 Phone: +1 (407) 629-9464
Fax: +1 (407) 629-2106

International Affiliates:
Canada Mexico United Kingdom Asia Pacific
Bristol Babcock, Canada BBI, S.A. de C.V. Bristol Babcock Ltd. Bristol Babcock, Inc.
234 Attwell Drive Homero No. 1343, 3er Piso Blackpole Road PO Box 1987
Toronto, Ont. M9W 5B3 Col. Morales Polanco Worcester, WR3 8YB Bunbury, Western Australia
Canada 11540 Mexico, D.F. United Kingdom 6231
PH: 416-675-3820 Mexico PH: +44 (0) 1905 856950 PH: +61 (0) 8 9791 3654
FAX: 416-674-5129 PH: (52-55)-52-81-81-12 FAX: +44 (0) 1905 856969 FAX: +61 (0) 8 9791 3173
FAX: (52-55)-52-81-81-09
Victoria, Australia
PH: +61 (0) 3 9384 2171
Calgary Office Villahermosa Office Middle East FAX: +61 (0) 3 8660 2501
Bristol Babcock, Canada BBI, S.A. de C.V. Bristol Babcock Ltd.
3812 Edmonton Trail N.E. Av. Plomo No.2 Blackpole Road
Calgary, Alberta T2E 5T6 Bodega No. 1 - Ciudad Worcester, WR3 8YB
Canada Industrial United Kingdom
PH: 403-265-4808 Villahermosa, Tabasco 86010 PH: +44 (0) 1905 856950
FAX: 403-233-2914 Mexico FAX: +44 (0) 1905 856969
PH: 52-993-353-3142
FAX: 52-993-353-3145

RC Rev: 05-Feb-04