Participant ID 241719404627

Participant Name SAGENI ANIL KUMAR

Test Center Name Xeon Technologies
Test Date 27/03/2025
Test Time 2:00 PM - 4:30 PM
Subject Mechanical Engineer

Section : English Language

Q.1 Select the most appropriate option to fill in the blank.

No book, any electronic material or smart watches _____ allowed inside the exam hall.
Ans 1. is

2. are

3. were

4. had

Question ID : 4410095355
Option 1 ID : 44100921215
Option 2 ID : 44100921214
Option 3 ID : 44100921216
Option 4 ID : 44100921217
Status : Answered
Chosen Option : 2

Q.2 Sentences of a paragraph are given below. While the first and the last sentences (S1 and S6)
are in the correct order, the sentences in between are jumbled up. Arrange the sentences in the
correct order to form a meaningful and coherent paragraph.

S1: One day Matilda met Mrs. Forestier on the roadside.

P: The one she had returned was a replacement.
Q: Matilda said it had taken her ten years of hard labour to repay the loan.
R: Mrs. Forestier could not recognise her friend.
S: Matilda told her about the loss of the borrowed necklace.
S6: Mrs. Forestier said it was a false one.
Ans 1. RSQP

2. PSQR

3. SRQP

4. QPRS

Question ID : 4410095954
Option 1 ID : 44100923593
Option 2 ID : 44100923594
Option 3 ID : 44100923595
Option 4 ID : 44100923596
Status : Answered
Chosen Option : 1
Q.3 Select the most appropriate option that can substitute the underlined segment in the sentence.

Rita was determined to achieve something enough to chase after her dream of becoming a
film actress.
Ans 1. tenacious

2. resolute

3. assertive

4. diligent

Question ID : 4410095978
Option 1 ID : 44100923690
Option 2 ID : 44100923689
Option 3 ID : 44100923692
Option 4 ID : 44100923691
Status : Answered
Chosen Option : 4

Q.4 Sentences of a paragraph are given below. While the first and the last sentences (S1 and S6)
are in the correct order, the sentences in between are jumbled up. Arrange the sentences in the
correct order to form a meaningful and coherent paragraph.

S1: The demise of castles can ultimately be attributed to gunpowder.

P: But the first gunpowder weapons were unreliable, inaccurate, and weak by standards.
Q: This greatly undermined the military role of castles.
R: During the 15th century, artillery became powerful enough to break through stone walls.
S: Gunpowder was first introduced to Europe during the 14th century.
S6: Castles were then replaced by artillery forts that had no role in civil administration.
Ans 1. PSQR

2. SPRQ

3. QRSP

4. RPSQ

Question ID : 4410095960
Option 1 ID : 44100923619
Option 2 ID : 44100923618
Option 3 ID : 44100923620
Option 4 ID : 44100923617
Status : Answered
Chosen Option : 2

Q.5 Select the most appropriate ANTONYM of the given word.

Mitigate
Ans 1. Increase

2. Reduce

3. Produce

4. Militate

Question ID : 4410096042
Option 1 ID : 44100923945
Option 2 ID : 44100923946
Option 3 ID : 44100923947
Option 4 ID : 44100923948
Status : Answered
Chosen Option : 2
Q.6 Select the most appropriate option to fill in the blank.

We met her _______ the Ayodhya Ram Lalla Temple when we went on a pilgrimage.
Ans 1. in

2. at

3. with

4. by

Question ID : 4410098057
Option 1 ID : 44100931952
Option 2 ID : 44100931953
Option 3 ID : 44100931955
Option 4 ID : 44100931954
Status : Answered
Chosen Option : 2

Q.7 Select the most appropriate option that can substitute the segment in brackets to fill in the
blank.

It was my teacher’s unique __________ (the approach or style of teaching) that made her
favourite of every student.
Ans 1. pedagogy

2. aesthetics

3. andragogy

4. didactics

Question ID : 4410095985
Option 1 ID : 44100923717
Option 2 ID : 44100923720
Option 3 ID : 44100923718
Option 4 ID : 44100923719
Status : Answered
Chosen Option : 4

Q.8 Rectify the error in the sentence by selecting the correct spelling from the options.

The catheters are inserted into the body through a small incission in the groin.
Ans 1. incession

2. incision

3. incesion

4. inceseion

Question ID : 4410096037
Option 1 ID : 44100923928
Option 2 ID : 44100923926
Option 3 ID : 44100923925
Option 4 ID : 44100923927
Status : Answered
Chosen Option : 1
Q.9 Select the most appropriate option to fill in the blank.

Rakshana _______ reached the railway junction in time.

Ans 1. fairly

2. soon

3. nearly

4. even

Question ID : 4410098053
Option 1 ID : 44100931936
Option 2 ID : 44100931939
Option 3 ID : 44100931938
Option 4 ID : 44100931937
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.10 Select the idiom that can substitute the underlined segment.

The teacher instructed Rita that all the synonyms and antonyms given in the textbook
exercises should be memorised.
Ans 1. should be a little fishy

2. should be faced

3. should be thick in the head

4. should be learnt by heart

Question ID : 4410096021
Option 1 ID : 44100923863
Option 2 ID : 44100923862
Option 3 ID : 44100923861
Option 4 ID : 44100923864
Status : Answered
Chosen Option : 3

Q.11 Select the most appropriate synonym of the given word.

Grit
Ans 1. Courage and determination

2. Well known

3. Power to beat

4. Innocent and illiterate

Question ID : 4410096045
Option 1 ID : 44100923960
Option 2 ID : 44100923957
Option 3 ID : 44100923959
Option 4 ID : 44100923958
Status : Answered
Chosen Option : 1
Q.12 Select the most appropriate article to fill in the blank. If no article is required, select ‘No article
required’.

Radhu has lost _____ book which her uncle gave her as a birthday present.
Ans 1. No article required

2. a

3. an

4. the

Question ID : 4410097030
Option 1 ID : 44100927866
Option 2 ID : 44100927863
Option 3 ID : 44100927864
Option 4 ID : 44100927865
Status : Answered
Chosen Option : 2

Comprehension:
Read the given passage and answer the questions that follow.

The English language has been significantly influenced by Greek, especially in fields like
science, philosophy and the arts. Many English words, such as geography, architect and
encyclopaedia, have Greek origins, often entering the language through Latin or French. Greek
mythology has also contributed idioms like Achilles’ heel (a person's weakness) and Midas
touch (the ability to make a financial success of everything you do). This linguistic influence
highlights the enduring legacy of Greek culture. Understanding these contributions helps us
appreciate how ancient languages continue to shape modern communication. Even in
medicine and technology, Greek roots are evident in terms like biology, psychology and
telephone. The Greek alphabet has also influenced scientific symbols and mathematical
notations, further demonstrating the deep connection between Greek and modern academic
disciplines.

SubQuestion No : 13
Q.13 According to the passage, why did Greek have such a strong influence on English?
Ans 1. Greek was first used in England.

2. Greek is a widely spoken language today.

3. Many Greek words entered English through Latin and French due to their historical
significance.
4. The English language originated from Greek.

Question ID : 44100922028
Option 1 ID : 44100987831
Option 2 ID : 44100987834
Option 3 ID : 44100987832
Option 4 ID : 44100987833
Status : Answered
Chosen Option : 4
 Comprehension:
Read the given passage and answer the questions that follow.

The English language has been significantly influenced by Greek, especially in fields like
science, philosophy and the arts. Many English words, such as geography, architect and
encyclopaedia, have Greek origins, often entering the language through Latin or French. Greek
mythology has also contributed idioms like Achilles’ heel (a person's weakness) and Midas
touch (the ability to make a financial success of everything you do). This linguistic influence
highlights the enduring legacy of Greek culture. Understanding these contributions helps us
appreciate how ancient languages continue to shape modern communication. Even in
medicine and technology, Greek roots are evident in terms like biology, psychology and
telephone. The Greek alphabet has also influenced scientific symbols and mathematical
notations, further demonstrating the deep connection between Greek and modern academic
disciplines.

SubQuestion No : 14
Q.14 Identify the central theme of the passage.
Ans 1. The comparison of Greek with English

2. The fall of the Greek language in recent times

3. The ancient conflicts between Greek and English speakers

4. The influence of Greek on English idioms and academic vocabulary

Question ID : 44100922029
Option 1 ID : 44100987838
Option 2 ID : 44100987836
Option 3 ID : 44100987835
Option 4 ID : 44100987837
Status : Answered
Chosen Option : 4

Comprehension:
Read the given passage and answer the questions that follow.

The English language has been significantly influenced by Greek, especially in fields like
science, philosophy and the arts. Many English words, such as geography, architect and
encyclopaedia, have Greek origins, often entering the language through Latin or French. Greek
mythology has also contributed idioms like Achilles’ heel (a person's weakness) and Midas
touch (the ability to make a financial success of everything you do). This linguistic influence
highlights the enduring legacy of Greek culture. Understanding these contributions helps us
appreciate how ancient languages continue to shape modern communication. Even in
medicine and technology, Greek roots are evident in terms like biology, psychology and
telephone. The Greek alphabet has also influenced scientific symbols and mathematical
notations, further demonstrating the deep connection between Greek and modern academic
disciplines.

SubQuestion No : 15
Q.15 What is the most appropriate synonym of the word 'enduring' in the given passage?
Ans 1. Delicate

2. Lasting

3. Feeble

4. Momentary

Question ID : 44100922027
Option 1 ID : 44100987830
Option 2 ID : 44100987828
Option 3 ID : 44100987829
Option 4 ID : 44100987827
Status : Answered
Chosen Option : 2
 Comprehension:
Read the given passage and answer the questions that follow.

The English language has been significantly influenced by Greek, especially in fields like
science, philosophy and the arts. Many English words, such as geography, architect and
encyclopaedia, have Greek origins, often entering the language through Latin or French. Greek
mythology has also contributed idioms like Achilles’ heel (a person's weakness) and Midas
touch (the ability to make a financial success of everything you do). This linguistic influence
highlights the enduring legacy of Greek culture. Understanding these contributions helps us
appreciate how ancient languages continue to shape modern communication. Even in
medicine and technology, Greek roots are evident in terms like biology, psychology and
telephone. The Greek alphabet has also influenced scientific symbols and mathematical
notations, further demonstrating the deep connection between Greek and modern academic
disciplines.

SubQuestion No : 16
Q.16 According to the passage, which of the following words is derived from Greek?
Ans 1. Encyclopaedia

2. Comics

3. Physics

4. Pastor

Question ID : 44100922031
Option 1 ID : 44100987843
Option 2 ID : 44100987845
Option 3 ID : 44100987844
Option 4 ID : 44100987846
Status : Answered
Chosen Option : 1

Comprehension:
Read the given passage and answer the questions that follow.

The English language has been significantly influenced by Greek, especially in fields like
science, philosophy and the arts. Many English words, such as geography, architect and
encyclopaedia, have Greek origins, often entering the language through Latin or French. Greek
mythology has also contributed idioms like Achilles’ heel (a person's weakness) and Midas
touch (the ability to make a financial success of everything you do). This linguistic influence
highlights the enduring legacy of Greek culture. Understanding these contributions helps us
appreciate how ancient languages continue to shape modern communication. Even in
medicine and technology, Greek roots are evident in terms like biology, psychology and
telephone. The Greek alphabet has also influenced scientific symbols and mathematical
notations, further demonstrating the deep connection between Greek and modern academic
disciplines.

SubQuestion No : 17
Q.17 What is the tone of the passage?
Ans 1. Influential

2. Critical

3. Informative

4. Entertaining

Question ID : 44100922030
Option 1 ID : 44100987841
Option 2 ID : 44100987842
Option 3 ID : 44100987840
Option 4 ID : 44100987839
Status : Answered
Chosen Option : 3

Section : Quantitative Aptitude

Q.1 Vidhu lends a sum of money which becomes ₹6,500 after 3 years and ₹7,500 after 5 years at
the same simple interest rate. What is the annual rate of simple interest?
Ans 1. 11%

2. 10%

3. 12%

4. 6%

Question ID : 44100935867
Option 1 ID : 441009143001
Option 2 ID : 441009143000
Option 3 ID : 441009143002
Option 4 ID : 441009142999
Status : Answered
Chosen Option : 2

Q.2 Which of the following numbers is divisible by 11?

Ans 1. 234568

2. 132231

3. 987654

4. 856974

Question ID : 44100920147
Option 1 ID : 44100980323
Option 2 ID : 44100980321
Option 3 ID : 44100980324
Option 4 ID : 44100980322
Status : Answered
Chosen Option : 1

Q.3 A cistern has two inlet pipes, A and B, which can fill it in 12 hours and 18 hours, respectively.
There is also a drain pipe, C, that can empty the full cistern in 36 hours. If all three pipes are
opened together, then how long will it take to fill the cistern?
Ans 1. 10 hours

2. 12 hours

3. 6 hours

4. 9 hours

Question ID : 44100921210
Option 1 ID : 44100984590
Option 2 ID : 44100984589
Option 3 ID : 44100984588
Option 4 ID : 44100984587
Status : Answered
Chosen Option : 4
Q.4 A shopkeeper sells two types of grain mixtures, one containing 40% rice and the other
containing 60% rice. How many kilograms of each type of rice mixture should be combined to
obtain 70 kg of a mixture that contains 55% rice?
Ans 1. 18 kg of 40% rice and 52 kg of 60% rice

2. 15.3 kg of 40% rice and 54.7 kg of 60% rice

3. 20 kg of 40% rice and 50 kg of 60% rice

4. 17.5 kg of 40% rice and 52.5 kg of 60% rice

Question ID : 44100935845
Option 1 ID : 441009142912
Option 2 ID : 441009142914
Option 3 ID : 441009142911
Option 4 ID : 441009142913
Status : Answered
Chosen Option : 4

Q.5 The roots of the equation x2 – 6x + k = 0 are imaginary. Find the range of values for k.

Ans 1.

2.

3.

4.

Question ID : 44100937788
Option 1 ID : 441009150728
Option 2 ID : 441009150730
Option 3 ID : 441009150731
Option 4 ID : 441009150729
Status : Not Answered
Chosen Option : --

Q.6 A shopkeeper buys 10 kg of apples for ₹800 and sells 8 kg of same apples for ₹656. What is
his profit or loss percentage?
Ans 1. 2.5% profit

2. 1.5% profit

3. 2% loss

4. 1.2% loss

Question ID : 44100936357
Option 1 ID : 441009144944
Option 2 ID : 441009144942
Option 3 ID : 441009144943
Option 4 ID : 441009144941
Status : Answered
Chosen Option : 1
Q.7 Which of the following expressions is equivalent to (cosec A – sin A)(sec A – cos A)?
Ans 1.

2.

3.

4.

Question ID : 44100938508
Option 1 ID : 441009153593
Option 2 ID : 441009153594
Option 3 ID : 441009153591
Option 4 ID : 441009153592
Status : Not Answered
Chosen Option : --

Q.8 The marked price of an article is ₹15,000. A trade discount of 25% is offered, and an additional
scheme discount of 10% is applied on the new price. What is the final price?
Ans 1. ₹10,125

2. ₹10,325

3. ₹10,225

4. ₹10,025

Question ID : 44100921530
Option 1 ID : 44100985867
Option 2 ID : 44100985869
Option 3 ID : 44100985868
Option 4 ID : 44100985870
Status : Answered
Chosen Option : 1

Q.9 If Anita had scored 90 additional marks in her examination, then 15 times her new total would
have equaled the square of her original score. What was her actual score in the examination?
Ans 1. 45

2. 34

3. 42

4. 30

Question ID : 44100937942
Option 1 ID : 441009151351
Option 2 ID : 441009151349
Option 3 ID : 441009151350
Option 4 ID : 441009151348
Status : Not Answered
Chosen Option : --
Q.10 Convert into a vulgar fraction.

Ans
1.

2.

3.

4.

Question ID : 44100920167
Option 1 ID : 44100980401
Option 2 ID : 44100980404
Option 3 ID : 44100980402
Option 4 ID : 44100980403
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.11 The average score of 30 boys in a group test is recorded as 35. However, it was later
discovered that two scores of 30 were mistakenly recorded as 40, and one score of 29 was
incorrectly noted as 21. What is the correct average score of the group?
Ans 1. 39.3

2. 40.2

3. 38.7

4. 34.6

Question ID : 44100935758
Option 1 ID : 441009142569
Option 2 ID : 441009142570
Option 3 ID : 441009142568
Option 4 ID : 441009142567
Status : Answered
Chosen Option : 4

Q.12 A number is increased by 40% and then decreased by 25%. What is the net percentage
change?
Ans 1. 5% decrease

2. 5% increase

3. 4% decrease

4. 4% increase

Question ID : 44100921565
Option 1 ID : 44100986008
Option 2 ID : 44100986007
Option 3 ID : 44100986009
Option 4 ID : 44100986010
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.13 Two trains, one 150 metres long and the other 200 metres long, are moving in opposite
directions at speeds of 40 km/hr and 50 km/hr. How long will it take for them to cross each
other?
Ans 1. 10 seconds

2. 12 seconds

3. 14 seconds

4. 16 seconds

Question ID : 44100921183
Option 1 ID : 44100984480
Option 2 ID : 44100984481
Option 3 ID : 44100984479
Option 4 ID : 44100984482
Status : Answered
Chosen Option : 3

Q.14 A car travels 90 km at a speed of 45 km/hr, then 120 km at 60 km/hr and finally 210 km at 70
km/hr. What is the average speed for the entire journey?
Ans 1. 61.3 km/hr

2. 58.1 km/hr

3. 48 km/hr

4. 60 km /hr

Question ID : 44100937141
Option 1 ID : 441009148068
Option 2 ID : 441009148066
Option 3 ID : 441009148065
Option 4 ID : 441009148067
Status : Answered
Chosen Option : 4

Q.15 A train covers 120 km at a speed of 30 km/hr, then 180 km at 60 km/hr, and finally 240 km at
120 km/hr. Find the average speed of the train for the entire journey.
Ans 1. 58 km/hr

2. 68 km/hr

3. 65 km/hr

4. 60 km/hr

Question ID : 44100921200
Option 1 ID : 44100984549
Option 2 ID : 44100984548
Option 3 ID : 44100984550
Option 4 ID : 44100984547
Status : Answered
Chosen Option : 4
Q.16 The marked price of a washing machine is ₹30,000. A dealer offers a 15% discount on it. After
that, a festival discount of 5% is applied. What is the final selling price of the washing
machine?
Ans 1. ₹20,290

2. ₹24,225

3. ₹24,000

4. ₹22,000

Question ID : 44100936380
Option 1 ID : 441009145036
Option 2 ID : 441009145034
Option 3 ID : 441009145033
Option 4 ID : 441009145035
Status : Answered
Chosen Option : 2

Q.17 In a school, class A has boys and girls in the ratio 7 : 9, class B has boys and girls in the ratio 5
: 6, and class C has boys and girls in the ratio 8 : 9. Which class/classes has/have the highest
proportion of boys?
Ans 1. Both A and B

2. A

3. C

4. B

Question ID : 44100936442
Option 1 ID : 441009145284
Option 2 ID : 441009145281
Option 3 ID : 441009145283
Option 4 ID : 441009145282
Status : Answered
Chosen Option : 3
Q.18 The following frequency distribution represents the weights of 50 students of a class. What is
the median weight of the students (correct to 2 decimal places)?
Weight (in kg) Number of Students

40 - 45 8

45 - 50 10

50 - 55 6

55 - 60 12

60 - 65 10

65 - 70 4

Ans 1. 45.23 kg

2. 55.42 kg

3. 59.38 kg

4. 48.75 kg

Question ID : 44100937082
Option 1 ID : 441009147821
Option 2 ID : 441009147823
Option 3 ID : 441009147824
Option 4 ID : 441009147822
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.19 A bag contains 1 rupee, 50 paise and 25 paise coins in the ratio 1 : 7 : 11. If the total amount in
the bag is ₹2,639, then find the number of coins of 50 paise.
Ans 1. 2548

2. 1820

3. 364

4. 1001

Question ID : 44100938816
Option 1 ID : 441009154814
Option 2 ID : 441009154813
Option 3 ID : 441009154811
Option 4 ID : 441009154812
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.20

Ans 1. 7312/1203

2. 6587/1300

3. 8352/1407

4. 9879/1100

Question ID : 44100937223
Option 1 ID : 441009148436
Option 2 ID : 441009148439
Option 3 ID : 441009148438
Option 4 ID : 441009148437
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.21 A and B can complete a piece of work in 8 days. B alone can do it in 12 days. If A alone starts
the work and works for only 4 days and then leaves, then how many more days will B take to
finish the remaining work?
Ans 1. 9 days

2. 8 days

3. 10 days

4. 12 days

Question ID : 44100921207
Option 1 ID : 44100984577
Option 2 ID : 44100984576
Option 3 ID : 44100984575
Option 4 ID : 44100984578
Status : Answered
Chosen Option : 3

Q.22 AB is a chord of length of 12 cm of a circle with a radius of 10 cm. The tangents drawn at
points A and B meet at a common point D. What is the length of AD?
Ans 1. 7.5 cm

2. 6.6 cm

3. 8.4 cm

4. 9.2 cm

Question ID : 44100938234
Option 1 ID : 441009152502
Option 2 ID : 441009152503
Option 3 ID : 441009152501
Option 4 ID : 441009152500
Status : Not Answered
Chosen Option : --
Q.23 Water flows through a pipe with an inner radius of 1.4 cm at a speed of 6.3 m/sec. What is the

volume of water discharged by the pipe in 30 min?

Ans 1. 8,735.32 litre

2. 5,543.33 litre

3. 6,985.44 litre

4. 4,503.81 litre

Question ID : 44100938190
Option 1 ID : 441009152324
Option 2 ID : 441009152326
Option 3 ID : 441009152325
Option 4 ID : 441009152327
Status : Answered
Chosen Option : 1

Q.24 The HCF of two numbers is 36, and their LCM is 1296. If one of the numbers is 144, what is the
sum of the two numbers?
Ans 1. 524

2. 468

3. 632

4. 345

Question ID : 44100936056
Option 1 ID : 441009143747
Option 2 ID : 441009143746
Option 3 ID : 441009143748
Option 4 ID : 441009143745
Status : Answered
Chosen Option : 2

Q.25 The ratio of the present ages of two boys is 8 : 9. After 4 years, the ratio of their ages will be 12
: 13. What will be the ratio of their ages after 16 years?
Ans 1. 25 : 26

2. 32 : 33

3. 24 : 25

4. 25 : 27

Question ID : 44100938799
Option 1 ID : 441009154748
Option 2 ID : 441009154750
Option 3 ID : 441009154747
Option 4 ID : 441009154749
Status : Answered
Chosen Option : 3
Q.26 A field is in the shape of an equilateral triangle whose side is 20 m. What is the cost of levelling
the field at the rate of ₹40/m2?

Ans 1. ₹6,928

2. ₹4,706

3. ₹3,954

4. ₹5,388

Question ID : 44100938023
Option 1 ID : 441009151663
Option 2 ID : 441009151661
Option 3 ID : 441009151660
Option 4 ID : 441009151662
Status : Not Answered
Chosen Option : --

Q.27 A conical tent with a radius of 6 m and a height of 8 m is made of polyester. What is the cost of
the polyester used to make this tent, if the price of the polyester is ₹140 per m2?
(Given: π = 3.14)
Ans 1. ₹26,376

2. ₹25,452

3. ₹23,368

4. ₹24,582

Question ID : 44100938101
Option 1 ID : 441009151971
Option 2 ID : 441009151970
Option 3 ID : 441009151968
Option 4 ID : 441009151969
Status : Not Answered
Chosen Option : --

Q.28 A person's monthly income is increased by 10%, but his expenditure also increases by 20%. If
he used to save 20% of his income earlier, what is the new percentage of his savings?
(Corrected to 2 decimal places)
Ans 1. 12.73%

2. 10%

3. 8%

4. 9.57%

Question ID : 44100936137
Option 1 ID : 441009144076
Option 2 ID : 441009144077
Option 3 ID : 441009144079
Option 4 ID : 441009144078
Status : Answered
Chosen Option : 1
Q.29 A car covers a distance of 280 km in 7 h. If the car reduces its speed by 10 km/hr, how much
time (correct to 1 decimal place) will it take to cover the same distance?
Ans 1. 2.8 h

2. 9.3 h

3. 4.9 h

4. 6.7 h

Question ID : 44100937150
Option 1 ID : 441009148101
Option 2 ID : 441009148104
Option 3 ID : 441009148102
Option 4 ID : 441009148103
Status : Answered
Chosen Option : 2

Q.30 Find the compound interest gained on ₹10,000 at an annual interest rate of 20% compounded
annually for 2 years.
Ans 1. ₹14,440

2. ₹14,400

3. ₹4,400

4. ₹4,440

Question ID : 44100919808
Option 1 ID : 44100978966
Option 2 ID : 44100978963
Option 3 ID : 44100978964
Option 4 ID : 44100978965
Status : Answered
Chosen Option : 3

Q.31 A milkman adds water to milk to gain profit. He mixes water with milk priced at ₹30 per litre to
get a final mixture costing ₹25 per litre. What is the ratio of milk to water in the mixture?
(Assume water is available free of cost.)
Ans 1. 1 : 5

2. 1 : 6

3. 5 : 1

4. 6 : 1

Question ID : 44100919801
Option 1 ID : 44100978937
Option 2 ID : 44100978938
Option 3 ID : 44100978935
Option 4 ID : 44100978936
Status : Answered
Chosen Option : 3
Q.32 A mixture contains milk and water in the ratio 4 : 1. If there is 20 litres of milk in the mixture,
how much water should be added to make the ratio of milk and water 3 : 1?
Ans
1.

2.

3.

4.

Question ID : 44100936434
Option 1 ID : 441009145249
Option 2 ID : 441009145250
Option 3 ID : 441009145252
Option 4 ID : 441009145251
Status : Answered
Chosen Option : 2

Q.33 Simplify:

Ans 1. 3

2. 5.5

3. 3.3

4. 2.2

Question ID : 44100921607
Option 1 ID : 44100986176
Option 2 ID : 44100986175
Option 3 ID : 44100986178
Option 4 ID : 44100986177
Status : Answered
Chosen Option : 2
Q.34 The table below represents the daily pocket allowance of children in a locality. Given that the
mean pocket allowance is ₹20.2, what is the value of the frequency x?
Pocket Allowance (in ₹) Number of Children

10 - 14 7

14 - 18 15

18 - 22 x

22 - 26 12

26 - 30 10

Ans 1. 14

2. 16

3. 11

4. 12

Question ID : 44100936684
Option 1 ID : 441009146239
Option 2 ID : 441009146240
Option 3 ID : 441009146237
Option 4 ID : 441009146238
Status : Not Answered
Chosen Option : --

Section : Intellectual Potential Test

Q.1 In the following number-pairs, the second number is obtained by applying certain
mathematical operations to the first number. Select the pair in which the numbers are related
in the same way as are the numbers of the following pairs.
(Note: Operations should be performed on the whole numbers, without breaking down the
numbers into its constituent digits. E.g. 13 – Operations on 13 such as
adding/subtracting/multiplying etc. to 13 can be performed. Breaking down 13 into 1 and 3
and then performing mathematical operations on 1 and 3 is not allowed.)

86, 126
70, 110
Ans 1. 64, 100

2. 42, 72

3. 25, 65

4. 35, 70

Question ID : 4410091218
Option 1 ID : 4410094867
Option 2 ID : 4410094865
Option 3 ID : 4410094866
Option 4 ID : 4410094868
Status : Answered
Chosen Option : 3
Q.2 If 2 is added to each even digit and 1 is subtracted from each odd digit in the number 5379264,
what will be the sum of the digits which are first from the left and first from the right in the new
number thus formed?
Ans 1. 8

2. 10

3. 11

4. 12

Question ID : 4410091814
Option 1 ID : 4410097246
Option 2 ID : 4410097245
Option 3 ID : 4410097247
Option 4 ID : 4410097248
Status : Answered
Chosen Option : 2

Q.3 X is the mother of L. C is the wife of L. D is the son of C. D has a sister named
F. How is F related to L?
Ans 1. Wife

2. Daughter-in-law

3. Daughter

4. Sister

Question ID : 441009721
Option 1 ID : 4410092871
Option 2 ID : 4410092873
Option 3 ID : 4410092872
Option 4 ID : 4410092874
Status : Answered
Chosen Option : 3

Q.4 Read the given statements and conclusions carefully. Assuming that the information given in
the statements is true, even if it appears to be at variance with commonly known facts, decide
which of the given conclusions logically follow(s) from the statements.

Statements:
Some spades are hammers.
No hammer is a nail.
All nails are pipes.

Conclusions:
(I): Some spades are nails.
(II): All pipes can never be hammers.
Ans 1. Only conclusion II follows

2. Only conclusion I follows

3. Both conclusions I and II follow

4. Neither conclusion I nor II follows

Question ID : 4410091866
Option 1 ID : 4410097450
Option 2 ID : 4410097449
Option 3 ID : 4410097451
Option 4 ID : 4410097452
Status : Answered
Chosen Option : 1
Q.5 Select the set in which the numbers are related in the same way as are the numbers of the
following sets.
(NOTE: Operations should be performed on the whole numbers, without breaking down the
numbers into their constituent digits. E.g. 13 – Operations on 13 such as adding /subtracting
/multiplying to 13 can be performed. Breaking down 13 into 1 and 3 and then performing
mathematical operations on 1 and 3 is not allowed.)
(15, 48, 63)
(30, 32, 62)
Ans 1. (62, 18, 44)

2. (25, 41, 66)

3. (20, 40, 52)

4. (45, 27, 70)

Question ID : 4410091210
Option 1 ID : 4410094834
Option 2 ID : 4410094833
Option 3 ID : 4410094836
Option 4 ID : 4410094835
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.6 This question is based on the following words.

GAP ARK PEA HOP

In each of the words, each vowel is changed to the letter immediately following it in the English
alphabetical order and each consonant is changed to the letter immediately preceding it in the
English alphabetical order. In how many letter-clusters thus formed, will no vowel appear?
Ans 1. Four

2. One

3. Three

4. Two

Question ID : 441009655
Option 1 ID : 4410092610
Option 2 ID : 4410092607
Option 3 ID : 4410092609
Option 4 ID : 4410092608
Status : Answered
Chosen Option : 4
Q.7 Select the pair that follows the same pattern as that followed by the two pairs
given below. Both pairs follow the same pattern.

TIM : WKN
GUA : JWB
Ans 1. KUR : NWP
2. DBL : GDM
3. MAH : DBI
4. XNI : APH

Question ID : 441009723
Option 1 ID : 4410092881
Option 2 ID : 4410092882
Option 3 ID : 4410092879
Option 4 ID : 4410092880
Status : Answered
Chosen Option : 2

Q.8 Seven boxes A, B, C, D, E, F and G are kept one over the other but not necessarily in the same
order. Only three boxes are kept above A. Only one box is kept between G and A. Only three
boxes are kept between G and B. B is kept at some place above A. F is kept immediately below
B. E is kept at one of the places above C. D is not kept immediately above or below G. How
many boxes are kept below G?
Ans 1. 4

2. 3

3. 1

4. 2

Question ID : 441009794
Option 1 ID : 4410093166
Option 2 ID : 4410093165
Option 3 ID : 4410093163
Option 4 ID : 4410093164
Status : Answered
Chosen Option : 3
Q.9 Read the given statements and conclusions carefully. Assuming that the
information given in the statements is true, even if it appears to be at
variance with commonly known facts, decide which of the given
conclusion(s) logically follow(s) from the statements.

Statements:
All swords are pens.
No dagger is a sword.

Conclusions:
(I): Some pens are daggers.
(II): No dagger is a pen.
Ans 1. Neither conclusion (I) nor (II) follows.
2. Only conclusion (II) follows.
3. Only conclusion (I) follows.
4. Both conclusions (I) and (II) follow.

Question ID : 441009718
Option 1 ID : 4410092861
Option 2 ID : 4410092860
Option 3 ID : 4410092859
Option 4 ID : 4410092862
Status : Answered
Chosen Option : 2

Q.10 Which of the following letter-number clusters will replace the question mark (?) in the given
series to make it logically complete?

HNW 29, DPS 42, ZRO 55, VTK 68, RVG 81, ?
Ans 1. OWC 94

2. NXC 94

3. MYD 92

4. MXB 92

Question ID : 4410091000
Option 1 ID : 4410093994
Option 2 ID : 4410093996
Option 3 ID : 4410093993
Option 4 ID : 4410093995
Status : Answered
Chosen Option : 2
Q.11 Select the pair that follows the same pattern as that followed by the two pairs
given below. Both pairs follow the same pattern.

RJE : TID
SKM : UJL
Ans 1. BST : ZTS
2. PJM : RIL
3. LIM : JJN
4. MAJ : OZH

Question ID : 441009724
Option 1 ID : 4410092885
Option 2 ID : 4410092886
Option 3 ID : 4410092883
Option 4 ID : 4410092884
Status : Answered
Chosen Option : 2

Q.12 This question is based on the five, three-digit numbers given below.

(Left) 768 987 783 825 874 (Right)

(Example- 697 – First digit = 6, second digit = 9 and third digit = 7)

(NOTE: All operations to be done from left to right.)

What will be the resultant if the second digit of the highest number is multiplied with the third
digit of the lowest number?
Ans 1. 63

2. 45

3. 64

4. 56

Question ID : 441009654
Option 1 ID : 4410092605
Option 2 ID : 4410092604
Option 3 ID : 4410092606
Option 4 ID : 4410092603
Status : Answered
Chosen Option : 3

Q.13 In a certain code language, ‘our new car’ is coded as ‘xa oc pu’, ‘new friends came’ is coded as
‘mi ld xa’ and ‘came with car’ is coded as ‘ld oc ny’. How is ‘our’ coded in the given language?
Ans 1. oc

2. xa

3. ld

4. pu

Question ID : 4410091869
Option 1 ID : 4410097462
Option 2 ID : 4410097461
Option 3 ID : 4410097463
Option 4 ID : 4410097464
Status : Answered
Chosen Option : 4
Q.14 Which of the following letter-number clusters will replace the question mark (?) in the given
series to make it logically complete?

FIN53, ORW49, XAF45, GJO41, ?

Ans 1. RSX37

2. PSX36

3. PSX37

4. PSY37

Question ID : 441009647
Option 1 ID : 4410092575
Option 2 ID : 4410092574
Option 3 ID : 4410092573
Option 4 ID : 4410092576
Status : Answered
Chosen Option : 3

Q.15 D, E, F, G, M, N and O are sitting around a circular table facing the centre of the table. D sits
third to the left of M. E sits second to the left of N. Only M sits between G and E. O is not an
immediate neighbour of D. How many people sit between F and E when counted from the right
of F?
Ans 1. Four

2. Three

3. Two

4. One

Question ID : 441009433
Option 1 ID : 4410091724
Option 2 ID : 4410091723
Option 3 ID : 4410091722
Option 4 ID : 4410091721
Status : Marked For Review
Chosen Option : 3

Q.16 In the following number-pairs, the second number is obtained by applying certain
mathematical operations to the first number. Select the set in which the numbers are related in
the same way as are the numbers of the following sets.
(NOTE: Operations should be performed on the whole numbers, without breaking down the
numbers into its constituent digits. E.g. 13 – Operations on 13 such as adding / subtracting /
multiplying etc. to 13 can be performed. Breaking down 13 into 1 and 3 and then performing
mathematical operations on 1 and 3 is not allowed.)

23, 57
17, 45
Ans 1. 21, 63

2. 19, 39

3. 15, 41

4. 27, 74

Question ID : 4410091769
Option 1 ID : 4410097068
Option 2 ID : 4410097066
Option 3 ID : 4410097065
Option 4 ID : 4410097067
Status : Answered
Chosen Option : 3
Q.17 This question is based on the five, three-digit numbers given below.

(Left) 847 429 517 371 386 (Right)

(Example- 697 – First digit = 6, second digit = 9 and third digit = 7)

(NOTE: All operations to be done from left to right.)

What will be the resultant if the second digit of the highest number is multiplied with the
second digit of the lowest number?
Ans 1. 28

2. 26

3. 27

4. 25

Question ID : 441009653
Option 1 ID : 4410092600
Option 2 ID : 4410092598
Option 3 ID : 4410092599
Option 4 ID : 4410092597
Status : Answered
Chosen Option : 1

Q.18 Seven boxes, R, A, L, E, N, D and I, are kept one over the other but not necessarily in the same
order. No box is kept below N. Only four boxes are kept between A and R. Only D is kept
between L and R. E is kept immediately below A. What is the position of I from the top?
Ans 1. Fifth

2. Fourth

3. Third

4. Second

Question ID : 441009713
Option 1 ID : 4410092842
Option 2 ID : 4410092841
Option 3 ID : 4410092840
Option 4 ID : 4410092839
Status : Answered
Chosen Option : 3

Q.19 If 1 is added to each even digit and 2 is subtracted from each odd digit in the number 3527468,
how many digits will appear more than once in the new number thus formed?
Ans 1. Three

2. Two

3. None

4. One

Question ID : 4410091818
Option 1 ID : 4410097264
Option 2 ID : 4410097263
Option 3 ID : 4410097261
Option 4 ID : 4410097262
Status : Answered
Chosen Option : 2
Q.20 If + means −, − means ×, × means ÷ and ÷ means +, then what will come in place of the
question mark (?) in the following equation?

81 × 9 ÷ 14 + 4 − 4 = ?

Ans 1. 18

2. 13

3. 7

4. 10

Question ID : 4410091165
Option 1 ID : 4410094653
Option 2 ID : 4410094654
Option 3 ID : 4410094656
Option 4 ID : 4410094655
Status : Answered
Chosen Option : 3

Q.21 If ‘A’ stands for ‘÷’, ‘B’ stands for ‘×’, ‘C’ stands for ‘+’ and ‘D’ stands for ‘−', what will come in
place of the question mark (?) in the following equation?

20 D 52 A 4 C 7 B 3 = ?

Ans 1. 15

2. 21

3. 28

4. 33

Question ID : 4410091310
Option 1 ID : 4410095233
Option 2 ID : 4410095234
Option 3 ID : 4410095235
Option 4 ID : 4410095236
Status : Answered
Chosen Option : 3

Q.22 Based on the English alphabetical order, three of the following four letter-clusters are alike in a
certain way and thus form a group. Which letter-cluster DOES NOT belong to that group?
(Note: The odd one out is not based on the number of consonants/vowels or their position in
the letter-cluster.)
Ans 1. LOT

2. WZE

3. MQV

4. CFK

Question ID : 441009996
Option 1 ID : 4410093977
Option 2 ID : 4410093980
Option 3 ID : 4410093978
Option 4 ID : 4410093979
Status : Answered
Chosen Option : 3
Q.23 Seven boxes K, L, M, S, T, U and V are kept one over the other but not necessarily in the same
order. T is kept immediately above K. V is kept immediately above S. Only L is kept above M.
Only two boxes are kept above T. V is not kept at third position from the bottom. How many
boxes are kept between U and L?
Ans 1. Two

2. Three

3. One

4. Four

Question ID : 441009432
Option 1 ID : 4410091718
Option 2 ID : 4410091719
Option 3 ID : 4410091717
Option 4 ID : 4410091720
Status : Answered
Chosen Option : 2

Q.24 What should come in place of the question mark (?) in the given series?

115 97 81 67 55 ?
Ans 1. 30

2. 35

3. 40

4. 45

Question ID : 4410091183
Option 1 ID : 4410094728
Option 2 ID : 4410094727
Option 3 ID : 4410094726
Option 4 ID : 4410094725
Status : Answered
Chosen Option : 4

Q.25 In a certain code language, ‘pistachio healthy nut’ is coded as ‘tu hy si’ and ‘coffee healthy
drink’ is coded as ‘hy xe ph’. How is ‘healthy’ coded in the given language?
Ans 1. hy

2. tu

3. xe

4. ph

Question ID : 441009714
Option 1 ID : 4410092844
Option 2 ID : 4410092843
Option 3 ID : 4410092845
Option 4 ID : 4410092846
Status : Answered
Chosen Option : 1
Q.26 Kishor starts from Point A and drives 36 km towards east. He then takes a right turn, drives 34
km, turns right and drives 39 km. He then takes a right turn and drives 37 km. He takes a final
right turn, drives 3 km and stops at Point P. How far (shortest distance) and towards which
direction should he drive in order to reach Point A again? (All turns are 90-degree turns only,
unless specified.)
Ans 1. 2 km to the north

2. 1 km to the south

3. 4 km to the north

4. 3 km to the south

Question ID : 441009651
Option 1 ID : 4410092591
Option 2 ID : 4410092589
Option 3 ID : 4410092592
Option 4 ID : 4410092590
Status : Answered
Chosen Option : 2

Q.27 What should come in place of the question mark (?) in the given series?

127 119 111 103 95 87 ?

Ans 1. 79

2. 63

3. 77

4. 65

Question ID : 4410091703
Option 1 ID : 4410096806
Option 2 ID : 4410096805
Option 3 ID : 4410096807
Option 4 ID : 4410096808
Status : Answered
Chosen Option : 1

Q.28 Based on the English alphabetical order, three of the following four letter-clusters are alike in a
certain way and thus form a group. Which letter-cluster DOES NOT belong to that group?
(Note: The odd one out is not based on the number of consonants/vowels or their position in
the letter-cluster.)
Ans 1. GPY

2. NFW

3. ENW

4. IRA

Question ID : 441009642
Option 1 ID : 4410092556
Option 2 ID : 4410092554
Option 3 ID : 4410092555
Option 4 ID : 4410092553
Status : Answered
Chosen Option : 2
Q.29 Based on the English alphabetical order, three of the following four letter-cluster pairs are alike
in a certain way and thus form a group. Which letter-cluster pair DOES NOT belong to that
group?
(Note: The odd one out is not based on the number of consonants/vowels or their position in
the letter-cluster.)
Ans 1. QN-YP

2. ZW-HY

3. FC-NE

4. OI-PL

Question ID : 441009637
Option 1 ID : 4410092535
Option 2 ID : 4410092533
Option 3 ID : 4410092536
Option 4 ID : 4410092534
Status : Answered
Chosen Option : 4

Q.30 Seven boxes K, L, M, S, T, U and V are kept one over the other but not necessarily in the same
order. No box is kept above T. Only three boxes are kept between T and U. Only one box is kept
between L and S. S is kept immediately above U. Only four boxes are kept between L and M. K
is kept at some place above V. Which box is kept second below K?
Ans 1. U

2. L

3. S

4. T

Question ID : 441009431
Option 1 ID : 4410091716
Option 2 ID : 4410091713
Option 3 ID : 4410091714
Option 4 ID : 4410091715
Status : Answered
Chosen Option : 1

Q.31 Which of the following letter-clusters should replace # and % so that the pattern and
relationship followed between the letter-cluster pair on the left side of :: is the same as that on
the right side of :: ?

# : VEX :: PIN : %
Ans 1. # - SCS; % - TOT

2. # - SBR; % - TPV

3. # - TAS; % - RNU

4. # - TAR; % - RMT

Question ID : 4410091863
Option 1 ID : 4410097440
Option 2 ID : 4410097439
Option 3 ID : 4410097437
Option 4 ID : 4410097438
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.32 W is the mother of E. E is the father of R. R is the brother of T. T is the wife of Y. How is W
related to Y?
Ans 1. Wife's mother's mother

2. Wife's mother's sister

3. Wife's father's mother

4. Wife's father's sister

Question ID : 441009804
Option 1 ID : 4410093205
Option 2 ID : 4410093206
Option 3 ID : 4410093203
Option 4 ID : 4410093204
Status : Answered
Chosen Option : 3

Q.33 A, B, C, D, E, F and G are sitting around a circular table facing the centre. Only one person sits
between F and A when counted from the right of F. Only one person sits between A and C. Only
one person sits between F and E. Only two people sit between G and C. Only one person sits
between B and E. How many people sit between B and F when counted from the left of B?
Ans 1. 2

2. 4

3. 3

4. 1

Question ID : 441009792
Option 1 ID : 4410093156
Option 2 ID : 4410093158
Option 3 ID : 4410093157
Option 4 ID : 4410093155
Status : Answered
Chosen Option : 1

Q.34 This question is based on the following words.

LEG PAW CUR BID

If in each of the words, each letter is changed to the letter following it in the English
alphabetical order, how many letter-clusters thus formed will have no vowel?
Ans 1. Three

2. Four

3. One

4. Two

Question ID : 4410091011
Option 1 ID : 4410094037
Option 2 ID : 4410094039
Option 3 ID : 4410094038
Option 4 ID : 4410094040
Status : Answered
Chosen Option : 1

Section : Domain Knowledge

Q.1 Which of the following factors significantly affects the efficiency of a centrifugal compressor?
Ans 1. The use of intercooling between compression stages.

2. The number of pistons used.

3. The presence of a crankshaft for motion transmission.

4. The shape and speed of the impeller.

Question ID : 44100941196
Option 1 ID : 441009164220
Option 2 ID : 441009164222
Option 3 ID : 441009164223
Option 4 ID : 441009164221
Status : Answered
Chosen Option : 4

Q.2 Which feature of CAD software helps in creating precise, scalable designs?
Ans 1. 3D rendering

2. Image filter tools

3. Grid and snap settings

4. Freehand drawing tool

Question ID : 4410091382
Option 1 ID : 4410095524
Option 2 ID : 4410095523
Option 3 ID : 4410095522
Option 4 ID : 4410095521
Status : Not Answered
Chosen Option : --

Q.3 Which of the following is NOT a function of material management?

Ans 1. Marketing strategy

2. Inventory control

3. Procurement

4. Warehousing

Question ID : 4410099170
Option 1 ID : 44100936433
Option 2 ID : 44100936432
Option 3 ID : 44100936431
Option 4 ID : 44100936434
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.4 What is gear backlash?
Ans 1. The total runout of a gear during rotation

2. The hardness of the gear material

3. The thickness of a single gear tooth

4. The clearance or play between meshing gear teeth

Question ID : 44100943700
Option 1 ID : 441009174248
Option 2 ID : 441009174250
Option 3 ID : 441009174249
Option 4 ID : 441009174247
Status : Answered
Chosen Option : 4

Q.5 Which of the following metals is commonly alloyed with iron to produce tool steels?
Ans 1. Lead

2. Tungsten

3. Copper

4. Zinc

Question ID : 4410092580
Option 1 ID : 44100910365
Option 2 ID : 44100910367
Option 3 ID : 44100910364
Option 4 ID : 44100910366
Status : Answered
Chosen Option : 2

Q.6 The symbol used to represent 'Inspection' in a flow process chart used in a work study is given
by (a/an):
Ans 1. square

2. Dee

3. triangle

4. arrow

Question ID : 441009875
Option 1 ID : 4410093488
Option 2 ID : 4410093490
Option 3 ID : 4410093489
Option 4 ID : 4410093487
Status : Answered
Chosen Option : 4
Q.7 A company produces a product with the following cost structure:
Fixed Costs = $500,000
Variable Cost per Unit = $25
Selling Price per Unit = $50
If the company wants to achieve a profit of $200,000, how many units must be sold?
Ans 1. 28,000 units

2. 14,000 units

3. 35,000 units

4. 20,000 units

Question ID : 4410099181
Option 1 ID : 44100936476
Option 2 ID : 44100936475
Option 3 ID : 44100936478
Option 4 ID : 44100936477
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.8 What is the main purpose of limits, fits, and tolerances in manufacturing?
Ans 1. To ensure proper assembly and interchangeability

2. To reduce the production cost only

3. To increase the weight of the components

4. To eliminate the need for machining

Question ID : 44100943472
Option 1 ID : 441009173340
Option 2 ID : 441009173341
Option 3 ID : 441009173339
Option 4 ID : 441009173342
Status : Answered
Chosen Option : 1

Q.9 Reaming is primarily used for achieving:

Ans 1. lower MRR

2. higher MRR

3. improved dimension tolerance

4. improved position tolerance

Question ID : 4410093267
Option 1 ID : 44100913078
Option 2 ID : 44100913077
Option 3 ID : 44100913075
Option 4 ID : 44100913076
Status : Answered
Chosen Option : 3
Q.10 Two-stroke engines in comparison to four-stroke engines have:
Ans 1. better power output and low mechanical simplicity

2. better power output and greater mechanical simplicity

3. low power output and low mechanical simplicity

4. low power output and greater mechanical simplicity

Question ID : 4410091913
Option 1 ID : 4410097639
Option 2 ID : 4410097637
Option 3 ID : 4410097638
Option 4 ID : 4410097640
Status : Answered
Chosen Option : 2

Q.11 What is the full form of COMSOAL?

Ans 1. Computerised Simulation and Optimisation of Assembly Line

2. Computer Method for Sequencing Operations for Assembly Lines

3. Computerised Solution of Assembly Line Balancing

4. Computerised Simulation of Assembly Line

Question ID : 4410099168
Option 1 ID : 44100936425
Option 2 ID : 44100936426
Option 3 ID : 44100936424
Option 4 ID : 44100936423
Status : Answered
Chosen Option : 1

Q.12 A heavier flywheel is required in which of the following?

Ans 1. Flywheel is not required in operation of two and four stroke engines

2. Two stroke engines relative to four stroke engines

3. Both two and four stroke require same type of flywheel

4. Four stroke engines relative to two stroke engines

Question ID : 4410091924
Option 1 ID : 4410097684
Option 2 ID : 4410097681
Option 3 ID : 4410097683
Option 4 ID : 4410097682
Status : Answered
Chosen Option : 4
Q.13 The glass transition temperature (Tg) of a polymer refers to:
Ans 1. the temperature at which it melts

2. the temperature at which it transitions from glassy to rubbery state

3. the temperature at which it starts to burn

4. the temperature at which it becomes crystalline

Question ID : 4410091259
Option 1 ID : 4410095032
Option 2 ID : 4410095030
Option 3 ID : 4410095029
Option 4 ID : 4410095031
Status : Not Answered
Chosen Option : --

Q.14 When selecting plant and equipment for a manufacturing operation, which of the following
factors will have the greatest impact on determining the break-even point (BEP)?
Ans 1. The depreciation rate of the equipment over its useful life

2. The variability in the cost of raw materials used by the equipment

3. The fixed operational costs associated with the equipment

4. The initial capital investment required for the equipment

Question ID : 4410099182
Option 1 ID : 44100936480
Option 2 ID : 44100936482
Option 3 ID : 44100936481
Option 4 ID : 44100936479
Status : Answered
Chosen Option : 2

Q.15 The power to weight ratio for external combustion engines as compared to internal
combustion engines:
Ans 1. is high

2. is low

3. is equal

4. can be greater or lower, it depends on the situation

Question ID : 4410091908
Option 1 ID : 4410097619
Option 2 ID : 4410097618
Option 3 ID : 4410097617
Option 4 ID : 4410097620
Status : Answered
Chosen Option : 1
Q.16 What is the expression for the slope θ(x) of the deflection curve of a beam?
Ans 1. θ(x) = y(x).

2. θ(x) = dy/dx.

3. θ(x) = d²y/dx².

4. θ(x) = ∫ y(x) dx.

Question ID : 44100942081
Option 1 ID : 441009167854
Option 2 ID : 441009167853
Option 3 ID : 441009167852
Option 4 ID : 441009167855
Status : Answered
Chosen Option : 2

Q.17 Which characteristic of Mixed Model Line Balancing allows flexibility in adjusting the output of
different products?
Ans 1. Each product should have entirely different operations to maximise variety.

2. Products must have similar tasks and processing requirements to ensure smooth
workflow.
3. The production line must be stopped and reconfigured every time the product demand
changes.
4. Only identical products can be produced on the same assembly line.

Question ID : 4410099167
Option 1 ID : 44100936420
Option 2 ID : 44100936419
Option 3 ID : 44100936421
Option 4 ID : 44100936422
Status : Answered
Chosen Option : 2

Q.18 In order to move the cross slide, the feed screw is turned by rotating the:
Ans 1. square threaded screw

2. setover screw

3. handwheel

4. barrel

Question ID : 4410092167
Option 1 ID : 4410098608
Option 2 ID : 4410098607
Option 3 ID : 4410098606
Option 4 ID : 4410098605
Status : Answered
Chosen Option : 3
Q.19 Compute the value of 'Median' for the following data.

Item in data array 1 2 3 4 5 6 7

Time in minutes 4.2 4.3 4.7 4.8 5.1 5.4 5.8
Ans 1. 5.1

2. 4.7

3. 4.8

4. 4.9

Question ID : 4410091129
Option 1 ID : 4410094512
Option 2 ID : 4410094509
Option 3 ID : 4410094510
Option 4 ID : 4410094511
Status : Answered
Chosen Option : 3

Q.20 What does the number '22' in the refrigerant R-22 indicate?
Ans 1. The molecular weight of the refrigerant.

2. The boiling point of the refrigerant in °C.

3. A specific designation assigned based on chemical composition.

4. The pressure required for refrigeration cycle operation.

Question ID : 44100941206
Option 1 ID : 441009164261
Option 2 ID : 441009164260
Option 3 ID : 441009164262
Option 4 ID : 441009164263
Status : Answered
Chosen Option : 3

Q.21 In a transverse fillet weld subjected to a tensile force, the primary mode of stress in the weld
throat is:
Ans 1. bending stress

2. shear stress

3. tensile stress

4. compressive stress

Question ID : 4410098458
Option 1 ID : 44100933567
Option 2 ID : 44100933566
Option 3 ID : 44100933564
Option 4 ID : 44100933565
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.22 The compression ratio in case of diesel engines lies in the range of:
Ans 1. 24-28

2. 8-10

3. 2-3

4. 16-20

Question ID : 4410091912
Option 1 ID : 4410097636
Option 2 ID : 4410097634
Option 3 ID : 4410097633
Option 4 ID : 4410097635
Status : Answered
Chosen Option : 4

Q.23 In a quasi-static process, irreversibilities are:

Ans 1. maximised

2. unpredictable

3. dominant

4. negligible

Question ID : 4410091083
Option 1 ID : 4410094325
Option 2 ID : 4410094328
Option 3 ID : 4410094327
Option 4 ID : 4410094326
Status : Answered
Chosen Option : 4

Q.24 When a bolted joint is subjected to eccentric loading, which stress is primarily induced in the
bolt in addition to shear stress?
Ans 1. Bearing stress

2. Torsional stress

3. Impact stress

4. Bending stress

Question ID : 4410098210
Option 1 ID : 44100932554
Option 2 ID : 44100932553
Option 3 ID : 44100932555
Option 4 ID : 44100932552
Status : Answered
Chosen Option : 2
Q.25 Which process is used to increase the strength of aluminum alloys through controlled heating
and cooling?
Ans 1. Quenching

2. Annealing

3. Precipitation hardening

4. Normalising

Question ID : 4410092965
Option 1 ID : 44100911895
Option 2 ID : 44100911894
Option 3 ID : 44100911892
Option 4 ID : 44100911893
Status : Answered
Chosen Option : 2

Q.26 Which of the following CANNOT be considered as a part of a simple carburettor?

Ans 1. Nozzle with metering orifice

2. Throttle valve

3. Float chamber

4. Idling system

Question ID : 4410091925
Option 1 ID : 4410097688
Option 2 ID : 4410097686
Option 3 ID : 4410097685
Option 4 ID : 4410097687
Status : Answered
Chosen Option : 4

Q.27 Which of the following factors DOES NOT affect the bending stress in a beam?
Ans 1. Bending moment

2. Distance from the neutral axis

3. Length of the beam

4. Moment of inertia

Question ID : 44100942302
Option 1 ID : 441009168723
Option 2 ID : 441009168726
Option 3 ID : 441009168725
Option 4 ID : 441009168724
Status : Answered
Chosen Option : 4
Q.28 Which of the following statements is NOT correct for 'Product Layout'?
Ans 1. Smooth and continuous workflow

2. Better co-ordination and simple production planning and control

3. More process inventory

4. Less space requirement for same volume of production

Question ID : 441009720
Option 1 ID : 4410092867
Option 2 ID : 4410092870
Option 3 ID : 4410092868
Option 4 ID : 4410092869
Status : Marked For Review
Chosen Option : 3

Q.29 Which of the following is a key objective of material management in an organisation?

Ans 1. To procure materials at the lowest possible price, ignoring quality and supplier
reliability to maximise short-term savings
2. To ensure the right quality and quantity of materials are available at the right time, at
the lowest cost, while minimising waste and stockouts
3. To maintain a high level of inventory to prevent any potential stockouts, even if it
results in excessive storage costs
4. To prioritise material procurement based solely on immediate production needs,
without considering future demand fluctuations or long-term supplier relationships

Question ID : 4410099171
Option 1 ID : 44100936436
Option 2 ID : 44100936437
Option 3 ID : 44100936435
Option 4 ID : 44100936438
Status : Answered
Chosen Option : 2

Q.30 Which of the following processes is always quasi-static?

Ans 1. Reversible isothermal process

2. Free expansion of a gas

3. Combustion in an engine

4. Sudden compression of a piston

Question ID : 4410091139
Option 1 ID : 4410094551
Option 2 ID : 4410094549
Option 3 ID : 4410094552
Option 4 ID : 4410094550
Status : Answered
Chosen Option : 1
Q.31 Which of the following factors does NOT affect surface tension?
Ans 1. Temperature

2. Presence of surfactants

3. Nature of the liquid

4. Surface area of the liquid

Question ID : 4410092979
Option 1 ID : 44100911951
Option 2 ID : 44100911949
Option 3 ID : 44100911950
Option 4 ID : 44100911948
Status : Answered
Chosen Option : 4

Q.32 What happens when the diameter of the shank of a bolt is made smaller than the core
diameter of the thread (Dc)?
Ans 1. The shank absorbs more energy, making the bolt stronger and better at absorbing
shock.
2. The bolt becomes weaker and more likely to fail.

3. The thread bears most of the load, and the shank is unaffected.

4. The bolt becomes heavier and less efficient.

Question ID : 4410098203
Option 1 ID : 44100932525
Option 2 ID : 44100932524
Option 3 ID : 44100932526
Option 4 ID : 44100932527
Status : Answered
Chosen Option : 2

Q.33 Which of the following best describes the motion of the follower in a typical radial cam
mechanism?
Ans 1. Circular motion

2. Reciprocating or oscillating motion perpendicular to cam rotation

3. Translational motion along the cam axis

4. Rotational motion synchronised with the cam

Question ID : 4410093485
Option 1 ID : 44100913947
Option 2 ID : 44100913949
Option 3 ID : 44100913948
Option 4 ID : 44100913950
Status : Answered
Chosen Option : 4
Q.34 What is the function of the WBLOCK command in AutoCAD?
Ans 1. To change the colour of a block

2. To create wireframe models

3. To write a block to an external file

4. To delete a block from the library

Question ID : 4410092553
Option 1 ID : 44100910258
Option 2 ID : 44100910256
Option 3 ID : 44100910257
Option 4 ID : 44100910259
Status : Answered
Chosen Option : 3

Q.35 Which of the following is NOT a characteristic of brittle fracture?

Ans 1. Occurs at low temperatures or high strain rates

2. Rapid crack propagation

3. Ductile necking at the fracture site

4. Minimal plastic deformation before fracture

Question ID : 4410092967
Option 1 ID : 44100911903
Option 2 ID : 44100911900
Option 3 ID : 44100911902
Option 4 ID : 44100911901
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.36 The 'soap' present in soluble oil (a type of cutting fluid) acts as a/an:
Ans 1. cooling agent only

2. emulsifying agent only

3. lubricating, cooling as well as emulsifying agent

4. lubricating agent only

Question ID : 4410094929
Option 1 ID : 44100919543
Option 2 ID : 44100919544
Option 3 ID : 44100919545
Option 4 ID : 44100919542
Status : Answered
Chosen Option : 3
Q.37 A self-energising brake is one in which ____.
Ans 1. the friction force helps in applying the braking force

2. an external force is required to apply the brake

3. the brake operates without friction

4. no external force is needed

Question ID : 44100913675
Option 1 ID : 44100954521
Option 2 ID : 44100954522
Option 3 ID : 44100954523
Option 4 ID : 44100954524
Status : Marked For Review
Chosen Option : 1

Q.38 In a four-stroke cycle petrol engine, during suction stroke:

Ans 1. only petrol is sucked in

2. mixture of petrol and air is sucked in

3. only air is sucked in

4. Suction stroke is intermittent, thus cannot be judged precisely

Question ID : 4410091916
Option 1 ID : 4410097650
Option 2 ID : 4410097651
Option 3 ID : 4410097649
Option 4 ID : 4410097652
Status : Answered
Chosen Option : 2

Q.39 How does the COP of a refrigeration system change with an increase in
evaporator temperature?
Ans 1. COP remains constant
2. COP increases
3. COP becomes zero
4. COP decreases

Question ID : 44100941249
Option 1 ID : 441009164434
Option 2 ID : 441009164432
Option 3 ID : 441009164435
Option 4 ID : 441009164433
Status : Answered
Chosen Option : 2
Q.40 Two masses of 3 kg and 6 kg are attached at 0.2 m and 0.1 m radius in the same plane. What
should be the mass of a third counter mass at 0.15 m to balance the system?
Ans 1. 1 kg

2. 2 kg

3. 8 kg

4. 3 kg

Question ID : 44100914105
Option 1 ID : 44100956245
Option 2 ID : 44100956246
Option 3 ID : 44100956248
Option 4 ID : 44100956247
Status : Answered
Chosen Option : 3

Q.41 What is the function of coolant in a drilling operation?

Ans 1. To remove burrs from the hole

2. To clean the machine table

3. To increase spindle speed

4. To reduce heat and improve tool life

Question ID : 4410091356
Option 1 ID : 4410095417
Option 2 ID : 4410095420
Option 3 ID : 4410095418
Option 4 ID : 4410095419
Status : Answered
Chosen Option : 4

Q.42 Why does a multi-plate clutch transmit more torque than a single-plate clutch?
Ans 1. It has less contact area.

2. It has a larger diameter.

3. It has more friction surfaces.

4. It has a stronger pressure plate.

Question ID : 44100913953
Option 1 ID : 44100955628
Option 2 ID : 44100955626
Option 3 ID : 44100955627
Option 4 ID : 44100955625
Status : Answered
Chosen Option : 3
Q.43 Additives that are normally used for mixing with oils to increase lubricating and cooling
qualities of various oils are ______.
Ans 1. sulphur and chlorine

2. carbon and helium

3. hydrogen and nitrogen

4. sodium and potassium

Question ID : 4410094923
Option 1 ID : 44100919520
Option 2 ID : 44100919521
Option 3 ID : 44100919519
Option 4 ID : 44100919518
Status : Answered
Chosen Option : 4

Q.44 Which of the following statements regarding strain energy in the elastic region is true?
Ans 1. Strain energy is completely recoverable when the load is removed.

2. Strain energy is entirely lost as heat during unloading.

3. Strain energy increases permanently with each load cycle.

4. Strain energy is only partially recoverable after unloading.

Question ID : 44100941851
Option 1 ID : 441009166945
Option 2 ID : 441009166946
Option 3 ID : 441009166947
Option 4 ID : 441009166944
Status : Answered
Chosen Option : 1

Q.45 Which instrument is commonly used to check parallelism in machine tool testing?
Ans 1. Vernier caliper

2. Hardness tester

3. Dial gauge and straightedge

4. Micrometer

Question ID : 44100943708
Option 1 ID : 441009174280
Option 2 ID : 441009174282
Option 3 ID : 441009174279
Option 4 ID : 441009174281
Status : Answered
Chosen Option : 3
Q.46 What is the primary safety advantage of the protected type flange coupling?
Ans 1. It minimises friction between the shaft and the coupling.

2. It enhances the torsional rigidity of the system.

3. It provides automatic lubrication to the shaft.

4. It protects the workman from injuries due to protruding bolts and nuts.

Question ID : 4410098524
Option 1 ID : 44100933830
Option 2 ID : 44100933831
Option 3 ID : 44100933828
Option 4 ID : 44100933829
Status : Answered
Chosen Option : 1

Q.47 In a combined cycle power plant, which of the following is used to generate additional power
after the gas turbine?
Ans 1. Wind turbine

2. Steam turbine

3. Nuclear reactor

4. Hydraulic turbine

Question ID : 4410091184
Option 1 ID : 4410094731
Option 2 ID : 4410094730
Option 3 ID : 4410094732
Option 4 ID : 4410094729
Status : Answered
Chosen Option : 2

Q.48 An Ideal fluid is one which has:

Ans 1. no velocity gradient

2. quadratic relation between shear stress and velocity gradient

3. linear behaviour between shear stress and velocity gradient

4. no resistance to shear stress

Question ID : 4410091387
Option 1 ID : 4410095543
Option 2 ID : 4410095542
Option 3 ID : 4410095541
Option 4 ID : 4410095544
Status : Answered
Chosen Option : 4
Q.49 The Delphi method is best described as:
Ans 1. a quantitative method that applies moving averages for forecasting

2. a method that forecasts by collecting expert opinions in multiple rounds

3. a method that uses historical data for trend analysis

4. a time-series technique for projecting future values

Question ID : 4410099125
Option 1 ID : 44100936255
Option 2 ID : 44100936253
Option 3 ID : 44100936252
Option 4 ID : 44100936254
Status : Answered
Chosen Option : 3

Q.50 The standard marking system of grinding wheels, as developed by the Indian standard marking
system, gives the indication about:
Ans 1. material removal rate

2. the time taken to complete the finishing of the workpiece

3. the hardness and grit size of the grinding wheel

4. the pressure between the grinding wheel and the workpiece

Question ID : 4410093304
Option 1 ID : 44100913223
Option 2 ID : 44100913224
Option 3 ID : 44100913225
Option 4 ID : 44100913226
Status : Answered
Chosen Option : 3

Q.51 Which of the following is an advantage of using the Hole Basis System in manufacturing?
Ans 1. Makes it difficult to achieve interchangeability

2. Requires less precision in manufacturing

3. Easier machining of holes with standard tools

4. Eliminates the need for tolerances

Question ID : 44100943521
Option 1 ID : 441009173538
Option 2 ID : 441009173536
Option 3 ID : 441009173535
Option 4 ID : 441009173537
Status : Answered
Chosen Option : 3
Q.52 Which of the following is a key characteristic of an open cycle gas turbine?
Ans 1. Operates only in a vacuum

2. The working fluid is continuously recirculated

3. Uses a heat exchanger to reuse heat

4. The working fluid is exhausted to the atmosphere

Question ID : 44100941290
Option 1 ID : 441009164631
Option 2 ID : 441009164628
Option 3 ID : 441009164630
Option 4 ID : 441009164629
Status : Answered
Chosen Option : 4

Q.53 What is a block in CAD software?

Ans 1. A pre-drawn object that can be reused multiple times.

2. A feature that deletes duplicate objects.

3. A tool for creating 3D models.

4. A setting that controls line thickness.

Question ID : 4410092551
Option 1 ID : 44100910249
Option 2 ID : 44100910250
Option 3 ID : 44100910248
Option 4 ID : 44100910251
Status : Not Answered
Chosen Option : --

Q.54 For a cantilever beam subjected to a point load W at its free end, what is the slope at the free
end?
Ans 1. θ = (W L²) / EI

2. θ = (W L) / EI

3. θ = (W L²) / 2EI

4. θ = (W L²) / 3EI

Question ID : 44100942272
Option 1 ID : 441009168608
Option 2 ID : 441009168607
Option 3 ID : 441009168609
Option 4 ID : 441009168610
Status : Answered
Chosen Option : 4
Q.55 Which of the following units is used for specific gravity?
Ans 1. kg/m³

2. m³/kg

3. g/cm³

4. No units

Question ID : 4410092976
Option 1 ID : 44100911936
Option 2 ID : 44100911938
Option 3 ID : 44100911937
Option 4 ID : 44100911939
Status : Answered
Chosen Option : 4

Q.56 The maximum deflection (δ_max) of a cantilever beam of length L subjected to a point load P
at its free end is given by:
Ans 1. PL³/(8EI)

2. PL³/(6EI)

3. PL³/(48EI)

4. PL³/(3EI)

Question ID : 44100941902
Option 1 ID : 441009167148
Option 2 ID : 441009167149
Option 3 ID : 441009167150
Option 4 ID : 441009167151
Status : Answered
Chosen Option : 4

Q.57 The length of a belt in a belt drive system is calculated using the formula L = 2C + π(D1 + D2) +
(D1 − D2)2/4C, where L is the total length of the belt, C is the centre distance, and D1, D2 are
the diameters of the pulleys. What does the term (D1 − D2)2/4C represent?
Ans 1. The additional length due to the difference in pulley sizes

2. The correction factor for friction

3. The extra length due to pulley alignment

4. The effect of belt tension

Question ID : 4410093632
Option 1 ID : 44100914523
Option 2 ID : 44100914526
Option 3 ID : 44100914524
Option 4 ID : 44100914525
Status : Answered
Chosen Option : 4
Q.58 Why is it important to apply uniform pressure while mounting a strain gauge?
Ans 1. To improve the flexibility of the gauge

2. To prevent the gauge from overheating

3. To increase the resistance of the strain gauge

4. To avoid air gaps and ensure proper adhesion

Question ID : 44100943253
Option 1 ID : 441009172473
Option 2 ID : 441009172474
Option 3 ID : 441009172472
Option 4 ID : 441009172471
Status : Answered
Chosen Option : 2

Q.59 The wages of a welder fabricating a structure is an example of a/an ____________.

Ans 1. direct cost

2. indirect cost

3. calculated cost

4. amplified cost

Question ID : 4410091087
Option 1 ID : 4410094342
Option 2 ID : 4410094343
Option 3 ID : 4410094344
Option 4 ID : 4410094341
Status : Answered
Chosen Option : 2

Q.60 As per the Indian standard system, the point angle in a normal drill is:
Ans 1. 90 degrees

2. 75 degrees

3. 118 degrees

4. 100 degrees

Question ID : 4410093255
Option 1 ID : 44100913028
Option 2 ID : 44100913027
Option 3 ID : 44100913030
Option 4 ID : 44100913029
Status : Answered
Chosen Option : 3
Q.61 If the properties such as velocity, pressure etc. change at a point with respect to time, the flow
is called _____ flow.
Ans 1. non-uniform

2. steady

3. unsteady

4. uniform

Question ID : 4410091138
Option 1 ID : 4410094546
Option 2 ID : 4410094547
Option 3 ID : 4410094548
Option 4 ID : 4410094545
Status : Answered
Chosen Option : 2

Q.62 Which of the following is the primary function of a helical compression spring?
Ans 1. To prevent axial displacement

2. To store and release energy

3. To resist bending stresses

4. To convert rotational motion into linear motion

Question ID : 44100942319
Option 1 ID : 441009168794
Option 2 ID : 441009168791
Option 3 ID : 441009168792
Option 4 ID : 441009168793
Status : Answered
Chosen Option : 2

Q.63 If a tire gauge reads 35 psi, what is the absolute pressure inside the tire, assuming
atmospheric pressure is 14.7 psi?
Ans 1. 35 psi

2. 14.7 psi

3. 49.7 psi

4. 20.3 psi

Question ID : 4410093179
Option 1 ID : 44100912733
Option 2 ID : 44100912731
Option 3 ID : 44100912734
Option 4 ID : 44100912732
Status : Answered
Chosen Option : 3
Q.64 Which command is used to change the appearance of dimensions in AutoCAD?
Ans 1. DIMSTYLE

2. DSETTINGS

3. DSTYLE

4. DIMEDIT

Question ID : 4410091400
Option 1 ID : 4410095595
Option 2 ID : 4410095594
Option 3 ID : 4410095593
Option 4 ID : 4410095596
Status : Answered
Chosen Option : 1

Q.65 In printing machines, cam and follower mechanisms are used to:
Ans 1. Transfer ink to the paper

2. Increase the pressure of printing rollers

3. Adjust the font size automatically

4. Feed paper sheets at regular intervals

Question ID : 4410093477
Option 1 ID : 44100913915
Option 2 ID : 44100913917
Option 3 ID : 44100913918
Option 4 ID : 44100913916
Status : Answered
Chosen Option : 4

Q.66 What is the primary function of a strain gauge?

Ans 1. To measure temperature changes

2. To measure electrical resistance directly

3. To measure strain in a material

4. To measure pressure variations

Question ID : 44100943228
Option 1 ID : 441009172371
Option 2 ID : 441009172374
Option 3 ID : 441009172372
Option 4 ID : 441009172373
Status : Answered
Chosen Option : 3
Q.67 Which of the following factors does NOT affect fluid pressure?
Ans 1. Gravitational acceleration

2. Area of the surface

3. Density of the fluid

4. Depth of the fluid

Question ID : 4410092980
Option 1 ID : 44100911955
Option 2 ID : 44100911954
Option 3 ID : 44100911953
Option 4 ID : 44100911952
Status : Answered
Chosen Option : 1

Q.68 Observed time for a worker is 0.7 minutes and his performance rating is 80%. Calculate the
normal time taken by the worker.
Ans 1. 0.875 minutes

2. 0.95 minutes

3. 0.7 minutes

4. 0.56 minutes

Question ID : 441009882
Option 1 ID : 4410093517
Option 2 ID : 4410093518
Option 3 ID : 4410093516
Option 4 ID : 4410093515
Status : Answered
Chosen Option : 4

Q.69 In oxyacetylene welding, if acetylene is observed to be in excess, the flame is called as:
Ans 1. reducing flame

2. originating flame

3. neutral flame

4. oxidising flame

Question ID : 4410094899
Option 1 ID : 44100919428
Option 2 ID : 44100919429
Option 3 ID : 44100919426
Option 4 ID : 44100919427
Status : Answered
Chosen Option : 1
Q.70 According to the ASHRAE numbering system, which of the following correctly represents the
refrigerant R-134a?
Ans 1. 1 Carbon, 3 Hydrogen, 4 Fluorine atoms

2. 1 Carbon, 2 Hydrogen, 3 Fluorine, 1 Chlorine atom

3. 2 Carbon, 2 Hydrogen, 4 Fluorine atoms

4. 1 Carbon, 4 Hydrogen, 2 Fluorine atoms

Question ID : 44100941239
Option 1 ID : 441009164392
Option 2 ID : 441009164393
Option 3 ID : 441009164394
Option 4 ID : 441009164395
Status : Answered
Chosen Option : 3

Q.71 The atoms in a simple cubic unit cell touch along:

Ans 1. the face diagonal

2. the corner

3. the body diagonal

4. the edge

Question ID : 4410092576
Option 1 ID : 44100910349
Option 2 ID : 44100910351
Option 3 ID : 44100910348
Option 4 ID : 44100910350
Status : Not Answered
Chosen Option : --

Q.72 In oxyacetylene gas welding, the temperature at the inner cone of neutral flame is around:
Ans 1. 2600°C

2. 2300°C

3. 4000°C

4. 3200°C

Question ID : 4410094889
Option 1 ID : 44100919392
Option 2 ID : 44100919393
Option 3 ID : 44100919390
Option 4 ID : 44100919391
Status : Answered
Chosen Option : 4
Q.73 For a simply supported beam subjected to a uniformly distributed load (UDL) of intensity w
(force per unit length) over its entire length L, what is the reaction force at each support?
Ans 1. (wL)/4.

2. wL.

3. (wL)/2.

4. (wL)/8.

Question ID : 44100942025
Option 1 ID : 441009167630
Option 2 ID : 441009167629
Option 3 ID : 441009167628
Option 4 ID : 441009167631
Status : Answered
Chosen Option : 3

Q.74 Which of the following operations CANNOT be included between CNC machining centres?
Ans 1. Welding

2. Drilling

3. Milling

4. Tapping

Question ID : 4410094917
Option 1 ID : 44100919496
Option 2 ID : 44100919495
Option 3 ID : 44100919494
Option 4 ID : 44100919497
Status : Answered
Chosen Option : 1

Q.75 What is the primary function of a bevel protractor?

Ans 1. To measure linear dimensions with high accuracy

2. To measure and set angles precisely

3. To check the flatness of a surface

4. To measure the diameter of cylindrical objects

Question ID : 44100943143
Option 1 ID : 441009172043
Option 2 ID : 441009172044
Option 3 ID : 441009172045
Option 4 ID : 441009172046
Status : Answered
Chosen Option : 2
Q.76 A CAD object is rotated by 30° about the Z-axis. If the initial coordinates of a point are (4, 0),
what will be the new coordinates after the rotation?
Ans 1. (3.46, 2)

2. (4, 1)

3. (0, 4)

4. (4, 2)

Question ID : 4410091386
Option 1 ID : 4410095540
Option 2 ID : 4410095538
Option 3 ID : 4410095539
Option 4 ID : 4410095537
Status : Not Answered
Chosen Option : --

Q.77 In an eddy current dynamometer, eddy currents are produced in the ____________.
Ans 1. bearings

2. stator coils

3. cooling fins

4. rotating disc

Question ID : 44100913746
Option 1 ID : 44100954804
Option 2 ID : 44100954801
Option 3 ID : 44100954803
Option 4 ID : 44100954802
Status : Not Answered
Chosen Option : --

Q.78 Which of the following represents the relationship between hoop strain (ε_h) and longitudinal
strain (ε_l) in a thin cylinder?
Ans 1. ε_h = 2ε_l

2. ε_h = 1/4 ε_l

3. ε_h = ε_l

4. ε_h = 1/2 ε_l

Question ID : 44100942361
Option 1 ID : 441009168951
Option 2 ID : 441009168954
Option 3 ID : 441009168952
Option 4 ID : 441009168953
Status : Answered
Chosen Option : 1
Q.79 Which material is commonly used for strain gauge sensing elements?
Ans 1. Aluminium

2. Constantan

3. Copper

4. Silver

Question ID : 44100943232
Option 1 ID : 441009172389
Option 2 ID : 441009172388
Option 3 ID : 441009172387
Option 4 ID : 441009172390
Status : Answered
Chosen Option : 3

Q.80 Which of the following is a critical characteristic of a workpiece that influences process
engineering decisions?
Ans 1. The packaging method used for transportation

2. The colour of the workpiece

3. The machinability and hardness of the material

4. The brand name of the raw material supplier

Question ID : 4410099115
Option 1 ID : 44100936215
Option 2 ID : 44100936212
Option 3 ID : 44100936213
Option 4 ID : 44100936214
Status : Answered
Chosen Option : 3

Q.81 Slip and creep are related to the operation of:

Ans 1. all types of belt drive systems

2. V-belt drive systems only

3. gear drive systems

4. flat belt drive systems only

Question ID : 4410093635
Option 1 ID : 44100914538
Option 2 ID : 44100914535
Option 3 ID : 44100914537
Option 4 ID : 44100914536
Status : Answered
Chosen Option : 1
Q.82 Man machine chart is a special type of:
Ans 1. string diagram

2. chronocycle graph

3. flow process chart

4. multiple activity chart

Question ID : 4410091091
Option 1 ID : 4410094359
Option 2 ID : 4410094360
Option 3 ID : 4410094358
Option 4 ID : 4410094357
Status : Not Answered
Chosen Option : --

Q.83 The load in a hydraulic dynamometer is controlled by ____.

Ans 1. increasing the brake pedal force

2. changing the air pressure

3. varying the electrical resistance

4. adjusting the quantity of working fluid

Question ID : 44100913695
Option 1 ID : 44100954604
Option 2 ID : 44100954603
Option 3 ID : 44100954601
Option 4 ID : 44100954602
Status : Answered
Chosen Option : 1

Q.84 Which type of feed is needed in facing operation?

Ans 1. Parallel to the axis of rotation

2. Perpendicular to the axis of rotation

3. Both parallel and perpendicular to the axis of rotation

4. Neither parallel nor perpendicular to the axis of rotation

Question ID : 4410093236
Option 1 ID : 44100912951
Option 2 ID : 44100912952
Option 3 ID : 44100912953
Option 4 ID : 44100912954
Status : Answered
Chosen Option : 3
Q.85 How does throttle governing affect the efficiency of a steam turbine?
Ans 1. Does not affect efficiency

2. Increases efficiency by improving heat recovery

3. Reduces efficiency due to throttling losses

4. Increases efficiency by reducing steam pressure drop

Question ID : 44100941322
Option 1 ID : 441009164806
Option 2 ID : 441009164807
Option 3 ID : 441009164805
Option 4 ID : 441009164804
Status : Answered
Chosen Option : 4