Read This First

Recent Cisco IOS releases have changed the way an unconfigured access
point behaves when booted for the first time. This section describes this
behavior and provides instructions on how to open the access point’s
configuration pages.

Cisco IOS Release 12.2(15)JA and Earlier

Setting Default Remarks

Login/Password Cisco/Cisco Case-sensitive
SSID tsunami —
Radio status Enabled —
IP Address Assigned by DHCP If DHCP disabled, the default
IP address is 10.0.0.1. See the
“Configuring the Access Point”
section on page 25 for
additional information.

Quick Start Guide Cisco Aironet 1200 Series Access Points 1

Cisco IOS Release 12.3(2)JA

Setting Default Remarks

Login/Password Cisco/Cisco Case-sensitive
SSID tsunami Case-sensitive
Radio status Enabled —
IP Address Assigned by DHCP If DHCP disabled, the access
point continues to send DHCP
requests indefinitely. To assign
an IP address, you must access
the unit’s console port. See the
“Assigning an IP Address
Using the CLI” section on page
33 for additional information.

2 78-16238-04
Cisco IOS Release 12.3(4)JA and Later

Setting Default Remarks

Login/Password Cisco/Cisco Case-sensitive
SSID None assigned You must create an SSID. See
the “Assigning an IP Address
Using the CLI” section on page
33
Radio status disabled You must enable the radio
interfaces. “Enabling the Radio
Interfaces” section on page 4
for additional information.
IP Address Assigned by DHCP If DHCP disabled, the access
point continues to send DHCP
requests indefinitely. To assign
an IP address, you must access
the unit’s console port. See the
“Assigning an IP Address
Using the CLI” section on page
33 for additional information.

Quick Start Guide Cisco Aironet 1200 Series Access Points 3

Enabling the Radio Interfaces
In Cisco IOS Release 12.3(4)JA and later, the access point radios are disabled
by default, and there is no SSID. You must create an SSID and enable the
radios before the access point will allow wireless associations from other
devices. These changes to the default configuration improve the security of
newly installed access points.
To enable the radio interfaces using the access point’s graphical user interface
(GUI), follow these instructions:
1. Use your internet browser to access your access point. The default login
and password is Cisco. Both are case-sensitive.
2. When the Summary Status page displays, click Express > SSID
Manager. The Global SSID Manager page appears.
3. Create an SSID for each radio interface. An SSID can be any
alphanumeric, case-sensitive entry from 2 to 32 characters. The
following six characters are not allowed: ?, “, $. [. \, and +. In addition,
the following three characters cannot be the first character: !, #, and ;.
4. Click Apply.
5. Click Network Interfaces > Radio 802.11b or Network Interfaces >
Radio 802.11g and the Radio Status page appears.
6. Click Settings and the Radio Settings Page appears.
7. Click Enable in the Enable Radio field.

4 78-16238-04
8. Click Apply.
9. Click Radio1-802.11A and the Radio Status page appears.
10. Repeat Steps 3 to 5.
11. Close your internet browser.

Note You can enable the radios using the access point’s Command
Line Interface (CLI). See the Cisco IOS Software
Configuration Guide for Cisco Aironet Access Points for
additional information.

Preface
This guide is designed to help you install and minimally configure your
IOS-based Cisco Aironet 1200 Series Access Point in a wireless Local Area
Network (LAN). Detailed installation and configuration information can be
found in the following documents:
• Cisco IOS Software Configuration Guide for Cisco Aironet Access
Points
• Aironet 1200 Series Access Point Installation and Configuration Guide
• Cisco IOS Command Reference for Cisco Aironet Access Points and
Bridges

Quick Start Guide Cisco Aironet 1200 Series Access Points 5

These documents are on Cisco.com. Another document, Radio Upgrade
Instructions: Cisco Aironet 1200 Series Access Points, is shipped with radio
upgrade kits for 2.4- and 5-GHz radios.
Follow these steps to access these documents:
1. Browse to http://www.cisco.com.
2. Click Technical Support and Documentation. Click it again in the
pop-up window that appears. The Technical Support and Documentation
page appears.
3. Click Wireless. The Wireless Support Resources page appears.
4. In the Wireless LAN Access section, click Cisco Aironet 1200 Series.
The Cisco Aironet 1200 Series page appears.
5. Select the document type you want to download (for example,
Configuration Guides). A list of documents for the type you selected
appears.
6. Click on the link for the document you wish to view. The document you
selected appears.

6 78-16238-04
Introduction to the Access Point
The Cisco Aironet 1200 Series Access Point delivers a high performance,
reliable, secure, and easily managed wireless LAN solution for enterprise
customers and for small- and medium-sized businesses. The access point is
designed to incorporate new technology enhancements as they become
available.
The 1200 series access point can contain two radios: a 2.4-GHz radio in an
internal mini-PCI slot and a 5-GHz radio module in an external, modified
cardbus slot. The access point supports one radio of each type, but does not
support two 2.4-GHz or two 5-GHz radios. You can configure the radios
separately, using different settings on each radio.
The access point can be configured from the factory for single-band
operation. You can field upgrade an access point preconfigured for
single-radio operation using a 5-GHz radio module or a 2.4-GHz radio card.
You can also order a preconfigured dual radio access point (1230AG series).
The 2.4-GHz mini-PCI radio card is available in two versions:
• IEEE 802.11b mini-PCI radio card (802.11b radio)
• IEEE 802.11g mini-PCI radio card (802.11g radio)
– Requires Cisco IOS Release 12.2 (13)JA or later

Quick Start Guide Cisco Aironet 1200 Series Access Points 7

The 5-GHz radio module connects to the access point’s modified card bus
connector and is available in three versions:
• Low power IEEE 802.11a radio module with integrated antenna (RM20A
radio module)
• Enhanced IEEE 802.11a radio module with dual integrated antennas
(RM21A radio module)
– Requires Cisco IOS Release 12.3(2)JA or later
• Enhanced IEEE 802.11a radio module with dual external RP-TNC
antenna connectors (RM22A radio module)
– Requires Cisco IOS Release 12.3 (2)JA or later

Tip If you are upgrading to an 802.11g radio or an RM21A or RM22A

radio module, make sure you are running the correct Cisco IOS
version before you install the radio or module. If your access point
is running an earlier version, it will not recognize the radio or
module and continually boot.

All 5-GHz radios incorporate an Unlicensed National Information Structure

(UNII) radio transceiver operating in the UNII 5-GHz frequency bands. The
RM20A and RM21A contain dual integrated omnidirectional antennas for

8 78-16238-04
diversity operation. In the graphical user interface (GUI) and the command
line interface (CLI), The 802.11b or 802.11g radio is referred to as Radio0
and the 802.11a radio is referred to as Radio1.
This guide provides information about the dual-band configuration running
the Cisco IOS operating system. Your access point configuration may vary
depending on the configuration you ordered.

Safety Information
The FCC with its action in ET Docket 96-8 has adopted a safety standard for
human exposure to radio frequency (RF) electromagnetic energy emitted by
FCC certified equipment. When used with approved Cisco Aironet antennas,
Cisco Aironet products meet the uncontrolled environmental limits found in
OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to
the instructions found in this manual and the Cisco Aironet 1200 Series
Access Point Hardware Installation Guide will result in user exposure that is
substantially below the FCC recommended limits.
• Do not touch or move antenna(s) while the unit is transmitting or
receiving.
• Do not hold any component containing a radio such that the antenna is
very close to or touching any exposed parts of the body, especially the
face and eyes, while transmitting.

Quick Start Guide Cisco Aironet 1200 Series Access Points 9

 • The use of wireless devices in hazardous locations is limited to the
constraints posed by the local codes, the national codes, and the safety
directors of such environments.

Warnings
Translated warnings of safety warnings are provided in a separate document
and in the Cisco Aironet 1200 Series Access Point Hardware Installation
Guide.

Warning Read the installation instructions before you connect the

system to its power source. Statement 1004

Warning This product relies on the building’s installation for

short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than 20A. Statement 1005

Warning Do not operate a portable transmitter near unshielded blasting

caps or in an explosive environment unless it is a type
especially qualified for such use. Statement 245B

10 78-16238-04
Warning Do not work on the system or connect or disconnect cables
during periods of lightning activity. Statement 1001

Warning In order to comply with FCC RF exposure limits, dipole

antennas should be located at a minimum of 7.9 in.
(20 cm) from the bodies of all persons. Statement 332

Unpacking the Access Point

Follow these steps to unpack the access point:
1. Open the shipping container and carefully remove the contents.
2. Return all packing materials to the shipping container and save it.
3. Ensure that all items listed in the “Package Contents” section are
included in the shipment. Check each item for damage. If any item is
missing or damaged, notify your authorized Cisco sales representative.

Note Antennas for the 2.4-GHz radio are not included in the shipping
container and must be ordered separately.

Quick Start Guide Cisco Aironet 1200 Series Access Points 11

Package Contents
Each access point package contains the following items:
• Cisco Aironet 1200 Series Access Point
• Cisco Aironet 1200 Series Power Module (Universal power supply)
• Cisco product registration and Cisco documentation feedback cards
• This guide

Installing the Access Point

Before you begin the installation process, please refer to the following
illustrations to familiarize yourself with the access point’s layout, features,
and connections.
This illustration shows the access point layout and connectors.

12 78-16238-04
 1 2 3 4 5 1 6 7

65850
1 2.4-GHz antenna connectors 5 Mode button
2 48-VDC power port 6 5-GHz antenna
3 Ethernet port (RJ-45) 7 Status LEDs
4 Console port (RJ-45)

Quick Start Guide Cisco Aironet 1200 Series Access Points 13

This illustration shows the access point with 5-GHz radio module (RM20A
or RM21A)

1 1 2 3

74631
1 Module mounting screws 3 Access point
2 Integrated antenna in patch
position (RM20A or RM21A
radio module)

14 78-16238-04
This illustration shows the RM22A radio module with external RP-TNC
antenna connectors.

1 Left RP-TNC antenna 4 Right/primary RP-TNC

connector antenna connector
2 5-Ghz RP-TNC label 5 5-GHz radio card
3 Module mounting screws

Quick Start Guide Cisco Aironet 1200 Series Access Points 15

Note See the Cisco Aironet 1200 Series Access Point Hardware
Installation Guide for a detailed description of the connections.

Additional Requirements
Before you install the access point, make sure you are using a computer
connected to the same network as the access point, and obtain the following
information from your system administrator:
• A host name (system name) for the access point
• The case-sensitive wireless service set identifier (SSID) for your radio
network
• If not connected to a DHCP server, a unique IP address for your access
point (such as 172.17.255.115)
• If the access point is not on the same subnet as your PC, a default
gateway address and subnet mask
• A Simple Network Management Protocol (SNMP) community name and
the SNMP file attribute (if SNMP is in use)

16 78-16238-04
Note Plan to configure the access point before mounting it in a relatively
inaccessible location. Some steps, such as those requiring a serial
cable, are easier to perform if the access point is accessible.

Attaching and Adjusting the Antennas

2.4-GHz Antennas
The access point supports single antenna or dual diversity antennas. Two
RP-TNC connectors are provided on the back of the unit for the 2.4-GHz
radio.
Attach the antennas to the RP-TNC connectors on the back of the access point
and hand tighten.
If you are using one antenna, attach the antenna or antenna cable to the
2.4-GHz Right/Primary RP-TNC connector.
If you are using two antennas for diversity coverage, attach the second
antenna or antenna cable to the 2.4-GHz Left RP-TNC antenna connector.

Quick Start Guide Cisco Aironet 1200 Series Access Points 17

If you are using a Cisco Aironet 2 dBi antenna, orient the antenna depending
on how you intend to mount the access point.
• On a table or desk, orient the antenna straight up.
• On a vertical surface, such as a wall, orient the antenna straight up.
• On a ceiling, orient the antenna straight down.
If you are using another Cisco Aironet antenna, refer to the antenna mounting
instructions that came with your antenna.

5-GHz Integrated Antenna

The 5-GHz integrated antenna is already installed. Deploy the antenna
depending on how the access point is mounted:
• Unfold the antenna housing if the access point is mounted on a
horizontal surface, such as a ceiling or desktop.
• Leave the housing in the folded position if the access point is mounted
on a vertical surface, such as a wall.

5-GHz External Antenna

The access point supports an RM22A radio module for use with a single
antenna or dual diversity antennas. Two RP-TNC antenna connectors are
provided on the back of the module for the 5-GHz radio.

18 78-16238-04
Note Be sure to connect your 5-GHz antennas to the 5-GHz radio antenna
connectors. The Cisco Aironet antenna cables have a blue marker
label near the antenna connector and the radio module has a
corresponding label near its 5-GHz antenna connectors.

If you are using one antenna, attach the antenna or antenna cable to the
5-GHz Right/Primary RP-TNC connector and hand tighten.
If you are using two antennas for diversity coverage, attach the second
antenna or antenna cable to the 5-GHz Left RP-TNC antenna connector.
This illustration shows the labelling of the antenna connections.

Quick Start Guide Cisco Aironet 1200 Series Access Points 19

This illustration shows the connectorized version with external antennas
installed.

1
1

121692
2 3
2

1 RP-TNC antenna connector 3 5-Ghz radio module

2 5-GHz antenna identifier
label

20 78-16238-04
Connecting to an Ethernet Network with an Inline
Power Source
Follow these steps to connect the access point to the Ethernet LAN when you
have an inline power source:
1. Connect the Ethernet cable to the RJ-45 Ethernet connector labeled
Ethernet on the access point. Connect the other end of the cable to one
of the following:

Caution Both the Ethernet and console ports use RJ-45 connectors. Be
careful when connecting the Ethernet cable to avoid connecting
to the console port.

a. A switch with inline power, such as a Cisco Catalyst 3550-24 PWR.

b. An inline power switch panel, such as a Cisco Catalyst Inline Power
Patch Panel.
c. The end of a Cisco Aironet power injector labeled To AP/Bridge and
the other end labeled To Network to the 10/100 Ethernet LAN.

Quick Start Guide Cisco Aironet 1200 Series Access Points 21

Connecting to an Ethernet Network with Local
Power
Follow these steps to connect the access point to an Ethernet LAN when you
have a local power source:
1. Connect the Ethernet cable to the RJ-45 Ethernet connector labeled
Ethernet on the access point.

Caution Both the Ethernet and console ports use RJ-45 connectors.
Make sure that you connect the Ethernet cable to the Ethernet
port and not to the console port.

2. Connect the power pack’s power output connector to the 48-VDC power
port labeled 48VDC on the access point.
3. Plug the other end of the power pack into an approved 100 to 240 VAC
outlet.

Powering Up the Access Point

When power is applied to the access point, it begins a routine power-up
sequence that you can monitor by observing the three LEDs on top of the
access point. All three LEDs on the top of the access point (Radio, Status, and

22 78-16238-04
Infrastructure) slowly blink amber, red, and green in sequence; the sequence
takes a couple of minutes to complete. Because the radios are disabled, the
Radio LED is dark.

Note See the Cisco Aironet 1200 Series Access Point Hardware
Installation Guide for a detailed description of the LED displays.

When the sequence is complete, you are ready to associate an IP address with
the access point and perform an initial configuration.

Obtaining and Assigning an IP Address

To browse to the access point’s Express Setup page, you must either obtain or
assign the access point’s IP address using one of the following methods:
• Connect to the access point console port and assign a static IP address.
• Use a DHCP server (if available) to automatically assign an IP address.
You can find out the DHCP-assigned IP address using one of the
following methods:
– Connect to the access point console port and use the show ip
interface brief command to display the IP address.
– Query the DHCP server using the access point’s MAC address to
identify the IP address. Your network administrator can do this.

Quick Start Guide Cisco Aironet 1200 Series Access Points 23

Using the Access Point’s Console Port
You can identify or assign an IP address using the access point’s console port
and a terminal emulator for all operating systems. However, if your
computer’s operating system is Windows CE, Linux, or Mac OS, you must
use the access point’s command-line console.
To access the command-line console, connect a DB-9 to RJ-45 serial cable
(Cisco part number AIR-CONCAB-1200) from your PC to the RS-232
console port on the access point. Then open a terminal emulator to view the
express setup screen and identify the IP address. Use these port settings for
the terminal session: 9600 baud, no parity, 8 data bits, 1 stop bit, and no flow
control.

Caution Both the Ethernet and console ports use RJ-45 connectors. Be
careful when connecting the console cable to avoid connecting
to the Ethernet port.

Procedures for using the command-line console can be found in the Cisco
Aironet 1200 Series Access Point Hardware Installation Guide. The guide is
available on Cisco.com.

24 78-16238-04
Configuring the Access Point
After you have determined or assigned the access point’s IP address, you can
open the access point management pages and initially configure the access
point. The access point must be connected to your network and your PC must
be on the same subnet. Follow these steps.
1. Open your Internet browser. You must use Microsoft Internet Explorer
(version 4.0 or later) or Netscape Navigator/ Communicator (version 4.0
or later).
2. Enter the access point’s IP address in the browser address line and press
Enter. The Summary Status screen appears.
3. From the Summary Status screen, click Setup and Express Setup. The
Express Setup screen appears.

Quick Start Guide Cisco Aironet 1200 Series Access Points 25

26 78-16238-04
Quick Start Guide Cisco Aironet 1200 Series Access Points 27
4. Enter the configuration settings you obtained from your system
administrator. The configurable settings include:
a. Host Name—The host name helps identify the access point on your
network

Note When you change the host name, the access point resets
the radios, causing associated clients to disassociate and
quickly reassociate.

b. Configuration Server Protocol—Click the button that matches the

network’s method of IP address assignment: DHCP or Static IP.
c. IP Address—Use this setting to assign or change the access point’s
IP address. If DHCP is enabled for your network, leave this field
blank.
d. IP Subnet Mask—Enter the IP subnet mask provided by your
network administrator so the IP can be recognized on the LAN. If
DHCP is enabled, leave this field blank.
e. Default Gateway—Enter the default gateway IP address provided
by your network administrator. If DHCP is enabled, leave this field
blank.

28 78-16238-04
 f. SNMP Community—If your network uses SNMP, enter the SNMP
Community name provided by your network administrator and
select the attributes of the SNMP data (also provided by your
network administrator).
g. Role in Radio Network—Click the button that describes the role of
the access point in your network. Select Access Point (Root) if your
access point is connected to the wired LAN. Select Repeater
(Non-Root) if it is not connected to the wired LAN. Select
Workgroup Bridge if you desire the access point to become a
workgroup bridge.

Note Configuring the access point as a workgroup bridge has

restrictions. For more information, see the Cisco Aironet 1200
Series Access Point Hardware Installation Guide.

h. Optimize Radio Network for—Use this setting to select either

preconfigured or customized settings for the access point radio.
Throughput optimizes the data volume handled by the access point
but might reduce its range. Range maximizes range but might
reduce throughput. Default uses the settings shipped from Cisco.
Custom uses the settings you enter on the Network Interfaces:
Radio-801.11b Settings page.

Quick Start Guide Cisco Aironet 1200 Series Access Points 29

 i. Aironet Extensions—Enable this setting if there are only Cisco
Aironet devices on your wireless LAN.
5. Click Apply or OK to save your settings. If you changed the access
point’s IP address, you lose your connection to the access point. Browse
to the new IP address to reconnect.

Note You can restore the access point to its factory defaults by unplugging
the power jack and plugging it back in while holding down the Mode
button for a few seconds or until the Status LED turns amber.

Configuring Security Settings

Cisco IOS Release 12.2 (15)JA and later include an Express Security page.
After you assign basic settings to your access point, you must configure
security settings to prevent unauthorized access to your network. Because it
is a radio device, the access point can communicate beyond the physical
boundaries of your work site.
Just as you use the Express Setup page to assign basic settings, you can use
the Express Security page to create unique SSIDs and assign one of four
security types to them. The following illustration shows the Express Security
page for Cisco IOS Release 12.3(2)JA.

30 78-16238-04
Quick Start Guide Cisco Aironet 1200 Series Access Points 31
32 78-16238-04
The following table briefly describes the four security settings you can assign
to an SSID using the Express Security page. In Cisco IOS Release 12.3(4)JA
or later, you must assign an SSID.

Security Type Description

No Security The least secure option. Use this option only for SSIDs
used in a public space and assign it to a VLAN that
restricts access to your network.
Static WEP More secure than no security. However, static WEP keys
Key are vulnerable to attack.
EAP Enables 802.1x authentication. Requires an IP address
Authentication and shared secret for an authentication server on your
network (server authentication port 1645). You do not
need to enter a WEP key.
WPA Wi-Fi Protected Access (WPA) permits wireless access to
users authenticated against a database through the
services of an authentication server, then encrypts their IP
traffic with stronger algorithms than those used in WEP.
As with EAP authentication, you must enter the IP address
and shared secret for an authentication server on your
network (server authentication port 1645).

Quick Start Guide Cisco Aironet 1200 Series Access Points 33

Refer to the Aironet 1200 Series Access Points, Cisco IOS Release xx.x(x) for
complete security information and configuration procedures.

In Case of Difficulty
If you followed the instructions in previous sections of this guide, you should
have had no trouble getting your access point installed and running. However,
if you did experience difficulty, help is available from Cisco. Before
contacting Cisco, look for a solution to your problem in the following places:
• The troubleshooting section of the Cisco Aironet 1200 Series Access
Point Hardware Installation Guide or the Cisco Aironet 1200 Series
Access Point Software Configuration Guide
• The Technical Assistance Center’s list of top wireless technology issues.
Follow these steps to access this list:
1. Open your browser and go to http://www.cisco.com/.
2. Click Technical Support -- Cisco TAC.
3. Click Top Issues.
4. Scroll down and click Wireless Technologies.
5. Click on the subject that addresses the problem you are experiencing.

34 78-16238-04
Assigning an IP Address Using the CLI
When you connect the access point to the wired LAN, the access point links
to the network using a bridge virtual interface (BVI) that it creates
automatically. Instead of tracking separate IP addresses for the access point’s
Ethernet and radio ports, the network uses the BVI.
When you assign an IP address to the access point using the CLI, you must
assign the address to the BVI. Beginning in a privileged EXEC mode, follow
these steps to assign an IP address to the access point’s BVI:

Command Purpose
Step 1 configure terminal Enter global configuration mode.
Step 2 Interface bvi1 Enters interface configuration mode
for the BVI.
Step 3 ip address address mask Assigns an IP address and subnet mask
address to the BVI.

Note If you used a Telnet session to connect to the access point, you lose
your connection when you assign a new IP address to the BVI. If you
need to continue configuring the access point using Telnet, use the
new IP address to open another Telnet session to the access point.

Quick Start Guide Cisco Aironet 1200 Series Access Points 35

Using a Telnet Session to Access the CLI
Follow these steps to browse to access the CLI using a Telnet session. These
steps are for a PC running Microsoft Windows with a Telnet terminal
application. Check your PC operating instructions for detailed instructions.
1. Select Start > Programs > Accessories > Telnet.
If Telnet is not listed in your Accessories menu, select Start > Run, type
Telnet in the entry field, and press Enter.
2. When the Telnet window appears, click Connect and select Remote
System.
3. In the Host Name field, type the access point’s IP address and click
Connect.

Mounting Instructions
You can mount the access point on any of the following surfaces:
• Horizontal or vertical flat surfaces, such as walls or ceilings
• Suspended ceilings
The access point ships with a detachable mounting bracket and the necessary
mounting hardware. Because it is detachable, you can use the mounting
bracket as a template to mark the positions of the mounting holes for your

36 78-16238-04
installation. You then install the mounting bracket and attach the access point
when you are ready. Refer to the following illustration to locate the various
mounting holes for the method you intend to use.
If you plan to mount the access point in an area subject to environmental air
space, Cisco recommends that you mount the access point horizontally so that
its antennas are pointing down, which results in the access point complying
with regulatory requirements for environmental air space.

1 2 3 4

65863
2 8 3 7 6 4 5

1 Access point mount 5 Locking detent

2 Cable tie points 6 Security hasp
3 Ceiling mount holes 7 Cable access hole
4 Access point mounts

Quick Start Guide Cisco Aironet 1200 Series Access Points 37

A mounting hardware kit is provided that contains the hardware and fasteners
necessary to mount the access point. Refer to the following table to identify
the materials you need to mount your access point, then go to the section
containing the specific mounting procedure.

Mounting Method Materials Required In Kit

Horizontal or vertical Four #8 x 1 in. (25.4 mm) screws Yes
surface Four wall anchors Yes
3/16 in. (4.7 mm) or 3/32 in. No
(2.3 mm) drill bit
Drill No
Standard screwdriver No
Suspended ceiling Two rail clips with studs Yes
Two plastic spacers Yes
Two 1/4–20 nuts with built-in Yes
washers
Standard screwdriver No
Appropriate wrench or pliers No

38 78-16238-04
Mounting on a Horizontal or Vertical Surface
Follow these steps to mount the access point on a horizontal or vertical
surface.
1. Use the mounting bracket as a template to mark the locations of the four
mounting holes.
2. Drill one of the following sized holes at the locations you marked:
• 3/16 in. (4.7 mm) if you are using wall anchors
• 1/8 in. (6.3 mm) if you are not using wall anchors
3. Install the anchors into the wall if you are using them. Otherwise, go to
Step 4.
4. Secure the mounting bracket to the surface using the #8 fasteners.

Note On a vertical surface, be sure to mount the bracket with its

security hasp facing down.

5. Attach the access point to the mounting bracket.

Quick Start Guide Cisco Aironet 1200 Series Access Points 39

Mounting on a Suspended Ceiling
The 1200 series wireless devices provide adequate fire resistance and low
smoke-producing characteristics suitable for operation in a building's
environmental air space in accordance with Section 300-22(C) of the
National Electrical Code (NEC), such as above suspended ceilings.

Note To comply with NEC code, a #10-24 grounding lug is provided on

the mounting bracket.

Follow these steps to mount your access point on a suspended ceiling. It may
be helpful to refer to the following illustration before beginning the process.

40 78-16238-04
 1

2
2
3

5
5

74121
1 Suspended ceiling T-rail 4 Mounting bracket
2 Rail clip 5 1/4-20 nut with attached washer
3 Plastic spacer

Quick Start Guide Cisco Aironet 1200 Series Access Points 41

1. Decide where you want to mount the access point.
2. Attach two rail clips to the ceiling’s T-rail.
3. Use the mounting bracket to adjust the distance between the rail clips so
that they align with the holes in the mounting bracket.
4. Use a standard screwdriver to tighten the rail clip studs in place on the
T-rail. Do not overtighten.
5. Install a plastic spacer on each rail clip stud. The spacer’s legs should
contact the ceiling grid T-rail.
6. Attach the mounting bracket to the rail clip studs and start a 1/4-20 nut
with attached washer on each stud.
7. Use a wrench or pliers to tighten the nuts. Do not overtighten.
8. Attach the access point to the mounting bracket.

Attaching the Access Point to the Mounting Bracket

Follow these steps to attach the access point to the mounting bracket.
1. Line up the three mounting pins on the access point with the large ends
of the keyhole-shaped holes on the mounting bracket.
2. Insert the access point into the keyhole shaped holes and maintain a
slight pressure to hold it in place.

42 78-16238-04
3. Slide the access point’s mounting pins into the small ends of the
keyhole-shaped holes on the mounting bracket and apply a slight force
on the I/O panel end. You will hear a click when the locking detent
contacts the access point and locks it into place.
4. Attach and adjust the antenna(s).
5. Connect the Ethernet cable to the access point’s Ethernet port.
6. Insert the 48-VDC power output connector into the access point’s local
power plug (if you are using a local power source).

Securing the Access Point to the Mounting Bracket

The security hasp on the mounting bracket locks the access point to the
bracket to make it more secure. When the access point is properly installed
on the mounting bracket, the holes in the security hasps line up so you can
install a padlock.

Note Known compatible padlocks are Master Lock models 120T or 121T.

Quick Start Guide Cisco Aironet 1200 Series Access Points 43

Mounting in a Hazardous Location
If you intend to mount the access point in a Division 2 Hazardous Location,
it must be installed according to the following illustration.

Non-hazardous Division 2 hazardous

location location

Power
injector AP-1210 OR
(optional) AP1231G-A-K9

Power
supply

117266
Option for mounting in hazardous locations applicable for AIR-AP-1210
and AIR-AP1231G-A-K9 part numbers only.

44 78-16238-04
Compliance Information
This equipment has been tested and found to comply with the European
Telecommunications Standard ETS 300.328 (2.4-GHz version) and ETS
301.893 (5-Ghz version). This standard covers Wideband Data Transmission
Systems referred to in CEPT recommendation T/R 10.01.
This type-accepted equipment is designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed in accordance with the instruction manual, may
cause harmful interference to radio communications.

Quick Start Guide Cisco Aironet 1200 Series Access Points 45

Cisco One-Year Limited Hardware
Warranty Terms
There are special terms applicable to your hardware warranty and
various services that you can use during the warranty period. Your
formal Warranty Statement, including the warranties and license
agreements applicable to Cisco software, is available on Cisco.com.
Follow these steps to access and download the Cisco Information
Packet and your warranty and license agreements from Cisco.com.
1. Launch your browser, and go to this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm
The Warranties and License Agreements page appears.
2. To read the Cisco Information Packet, follow these steps:
a. Click the Information Packet Number field, and make sure that
the part number 78-5235-03A0 is highlighted.
b. Select the language in which you would like to read the document.
c. Click Go.
The Cisco Limited Warranty and Software License page from the
Information Packet appears.

46 78-16238-04
 d. Read the document online, or click the PDF icon to download and
print the document in Adobe Portable Document Format (PDF).

Note You must have Adobe Acrobat Reader to view and print
PDF files. You can download the reader from Adobe’s
website: http://www.adobe.com

3. To read translated and localized warranty information about your

product, follow these steps:
a. Enter this part number in the Warranty Document Number field:
78-10747-01C0
b. Select the language in which you would like to view the document.
c. Click Go.
The Cisco warranty page appears.
d. Read the document online, or click the PDF icon to download and
print the document in Adobe Portable Document Format (PDF).
You can also contact the Cisco service and support website for assistance:
http://www.cisco.com/public/Support_root.shtml.

Duration of Hardware Warranty

One (1) Year

Quick Start Guide Cisco Aironet 1200 Series Access Points 47

Replacement, Repair, or Refund Policy for Hardware
Cisco or its service center will use commercially reasonable efforts to ship a
replacement part within ten (10) working days after receipt of a Return
Materials Authorization (RMA) request. Actual delivery times can vary,
depending on the customer location.
Cisco reserves the right to refund the purchase price as its exclusive warranty
remedy.

To Receive a Return Materials Authorization (RMA) Number

Contact the company from whom you purchased the product. If you
purchased the product directly from Cisco, contact your Cisco Sales and
Service Representative.
Complete the information below, and keep it for reference.

Company product purchased from

Company telephone number
Product model number
Product serial number
Maintenance contract number

48 78-16238-04